# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/dsa/realtek.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Realtek switches for unmanaged switches

allOf:
  - $ref: dsa.yaml#/$defs/ethernet-ports

maintainers:
  - Linus Walleij <linus.walleij@linaro.org>

description:
  Realtek advertises these chips as fast/gigabit switches or unmanaged
  switches. They can be controlled using different interfaces, like SMI,
  MDIO or SPI.

  The SMI "Simple Management Interface" is a two-wire protocol using
  bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
  not use the MDIO protocol. This binding defines how to specify the
  SMI-based Realtek devices. The realtek-smi driver is a platform driver
  and it must be inserted inside a platform node.

  The MDIO-connected switches use MDIO protocol to access their registers.
  The realtek-mdio driver is an MDIO driver and it must be inserted inside
  an MDIO node.

  The compatible string is only used to identify which (silicon) family the
  switch belongs to. Roughly speaking, a family is any set of Realtek switches
  whose chip identification register(s) have a common location and semantics.
  The different models in a given family can be automatically disambiguated by
  parsing the chip identification register(s) according to the given family,
  avoiding the need for a unique compatible string for each model.

properties:
  compatible:
    enum:
      - realtek,rtl8365mb
      - realtek,rtl8366rb
    description: |
      realtek,rtl8365mb:
        Use with models RTL8363NB, RTL8363NB-VB, RTL8363SC, RTL8363SC-VB,
        RTL8364NB, RTL8364NB-VB, RTL8365MB, RTL8366SC, RTL8367RB-VB, RTL8367S,
        RTL8367SB, RTL8370MB, RTL8310SR
      realtek,rtl8366rb:
        Use with models RTL8366RB, RTL8366S

  mdc-gpios:
    description: GPIO line for the MDC clock line.
    maxItems: 1

  mdio-gpios:
    description: GPIO line for the MDIO data line.
    maxItems: 1

  reset-gpios:
    description: GPIO to be used to reset the whole device
    maxItems: 1

  resets:
    maxItems: 1

  realtek,disable-leds:
    type: boolean
    description: |
      if the LED drivers are not used in the hardware design,
      this will disable them so they are not turned on
      and wasting power.

  interrupt-controller:
    type: object
    additionalProperties: false

    description: |
      This defines an interrupt controller with an IRQ line (typically
      a GPIO) that will demultiplex and handle the interrupt from the single
      interrupt line coming out of one of the Realtek switch chips. It most
      importantly provides link up/down interrupts to the PHY blocks inside
      the ASIC.

    properties:

      interrupt-controller: true

      interrupts:
        maxItems: 1
        description:
          A single IRQ line from the switch, either active LOW or HIGH

      '#address-cells':
        const: 0

      '#interrupt-cells':
        const: 1

    required:
      - interrupt-controller
      - '#address-cells'
      - '#interrupt-cells'

  mdio:
    $ref: /schemas/net/mdio.yaml#
    unevaluatedProperties: false

    properties:
      compatible:
        const: realtek,smi-mdio

if:
  required:
    - reg

then:
  $ref: /schemas/spi/spi-peripheral-props.yaml#
  not:
    required:
      - mdc-gpios
      - mdio-gpios
      - mdio

  properties:
    mdc-gpios: false
    mdio-gpios: false
    mdio: false

else:
  required:
    - mdc-gpios
    - mdio-gpios
    - mdio

required:
  - compatible

    #  - mdc-gpios
    #  - mdio-gpios
    #  - reset-gpios
    #  - mdio

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/gpio/gpio.h>
    #include <dt-bindings/interrupt-controller/irq.h>

    platform {
            switch {
                    compatible = "realtek,rtl8366rb";
                    /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
                    mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
                    mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
                    reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;

                    switch_intc1: interrupt-controller {
                            /* GPIO 15 provides the interrupt */
                            interrupt-parent = <&gpio0>;
                            interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
                            interrupt-controller;
                            #address-cells = <0>;
                            #interrupt-cells = <1>;
                    };

                    ports {
                            #address-cells = <1>;
                            #size-cells = <0>;
                            port@0 {
                                    reg = <0>;
                                    label = "lan0";
                                    phy-handle = <&phy0>;
                            };
                            port@1 {
                                    reg = <1>;
                                    label = "lan1";
                                    phy-handle = <&phy1>;
                            };
                            port@2 {
                                    reg = <2>;
                                    label = "lan2";
                                    phy-handle = <&phy2>;
                            };
                            port@3 {
                                    reg = <3>;
                                    label = "lan3";
                                    phy-handle = <&phy3>;
                            };
                            port@4 {
                                    reg = <4>;
                                    label = "wan";
                                    phy-handle = <&phy4>;
                            };
                            port@5 {
                                    reg = <5>;
                                    ethernet = <&gmac0>;
                                    phy-mode = "rgmii";
                                    fixed-link {
                                            speed = <1000>;
                                            full-duplex;
                                    };
                            };
                    };

                    mdio {
                            compatible = "realtek,smi-mdio";
                            #address-cells = <1>;
                            #size-cells = <0>;

                            phy0: ethernet-phy@0 {
                                    reg = <0>;
                                    interrupt-parent = <&switch_intc1>;
                                    interrupts = <0>;
                            };
                            phy1: ethernet-phy@1 {
                                    reg = <1>;
                                    interrupt-parent = <&switch_intc1>;
                                    interrupts = <1>;
                            };
                            phy2: ethernet-phy@2 {
                                    reg = <2>;
                                    interrupt-parent = <&switch_intc1>;
                                    interrupts = <2>;
                            };
                            phy3: ethernet-phy@3 {
                                    reg = <3>;
                                    interrupt-parent = <&switch_intc1>;
                                    interrupts = <3>;
                            };
                            phy4: ethernet-phy@4 {
                                    reg = <4>;
                                    interrupt-parent = <&switch_intc1>;
                                    interrupts = <12>;
                            };
                    };
            };
    };

  - |
    #include <dt-bindings/gpio/gpio.h>
    #include <dt-bindings/interrupt-controller/irq.h>

    platform {
            switch {
                    compatible = "realtek,rtl8365mb";
                    mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
                    mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
                    reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;

                    switch_intc2: interrupt-controller {
                            interrupt-parent = <&gpio5>;
                            interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
                            interrupt-controller;
                            #address-cells = <0>;
                            #interrupt-cells = <1>;
                    };

                    ports {
                            #address-cells = <1>;
                            #size-cells = <0>;
                            port@0 {
                                    reg = <0>;
                                    label = "swp0";
                                    phy-handle = <&ethphy0>;
                            };
                            port@1 {
                                    reg = <1>;
                                    label = "swp1";
                                    phy-handle = <&ethphy1>;
                            };
                            port@2 {
                                    reg = <2>;
                                    label = "swp2";
                                    phy-handle = <&ethphy2>;
                            };
                            port@3 {
                                    reg = <3>;
                                    label = "swp3";
                                    phy-handle = <&ethphy3>;
                            };
                            port@6 {
                                    reg = <6>;
                                    ethernet = <&fec1>;
                                    phy-mode = "rgmii";
                                    tx-internal-delay-ps = <2000>;
                                    rx-internal-delay-ps = <2000>;

                                    fixed-link {
                                            speed = <1000>;
                                            full-duplex;
                                            pause;
                                    };
                            };
                    };

                    mdio {
                            compatible = "realtek,smi-mdio";
                            #address-cells = <1>;
                            #size-cells = <0>;

                            ethphy0: ethernet-phy@0 {
                                    reg = <0>;
                                    interrupt-parent = <&switch_intc2>;
                                    interrupts = <0>;
                            };
                            ethphy1: ethernet-phy@1 {
                                    reg = <1>;
                                    interrupt-parent = <&switch_intc2>;
                                    interrupts = <1>;
                            };
                            ethphy2: ethernet-phy@2 {
                                    reg = <2>;
                                    interrupt-parent = <&switch_intc2>;
                                    interrupts = <2>;
                            };
                            ethphy3: ethernet-phy@3 {
                                    reg = <3>;
                                    interrupt-parent = <&switch_intc2>;
                                    interrupts = <3>;
                            };
                    };
            };
    };

  - |
    #include <dt-bindings/gpio/gpio.h>
    #include <dt-bindings/interrupt-controller/irq.h>

    mdio {
            #address-cells = <1>;
            #size-cells = <0>;

            switch@29 {
                    compatible = "realtek,rtl8365mb";
                    reg = <29>;

                    reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;

                    switch_intc3: interrupt-controller {
                            interrupt-parent = <&gpio0>;
                            interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
                            interrupt-controller;
                            #address-cells = <0>;
                            #interrupt-cells = <1>;
                    };

                    ports {
                            #address-cells = <1>;
                            #size-cells = <0>;

                            port@0 {
                                    reg = <0>;
                                    label = "lan4";
                            };

                            port@1 {
                                    reg = <1>;
                                    label = "lan3";
                            };

                            port@2 {
                                    reg = <2>;
                                    label = "lan2";
                            };

                            port@3 {
                                    reg = <3>;
                                    label = "lan1";
                            };

                            port@4 {
                                    reg = <4>;
                                    label = "wan";
                            };

                            port@7 {
                                    reg = <7>;
                                    ethernet = <&ethernet>;
                                    phy-mode = "rgmii";
                                    tx-internal-delay-ps = <2000>;
                                    rx-internal-delay-ps = <0>;

                                    fixed-link {
                                            speed = <1000>;
                                            full-duplex;
                                    };
                            };
                    };
            };
      };