spi/mcspi: allow configuration of pin directions
Allow D0 to be an input and D1 to be an output, configurable via
platform data and a new DT property.
Based on a patch from Matus Ujhelyi <matus.ujhelyi@streamunlimited.com>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 3542fdc..5104633 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -130,6 +130,7 @@
struct omap2_mcspi_dma *dma_channels;
struct device *dev;
struct omap2_mcspi_regs ctx;
+ unsigned int pin_dir:1;
};
struct omap2_mcspi_cs {
@@ -765,8 +766,15 @@
/* standard 4-wire master mode: SCK, MOSI/out, MISO/in, nCS
* REVISIT: this controller could support SPI_3WIRE mode.
*/
- l &= ~(OMAP2_MCSPI_CHCONF_IS|OMAP2_MCSPI_CHCONF_DPE1);
- l |= OMAP2_MCSPI_CHCONF_DPE0;
+ if (mcspi->pin_dir == MCSPI_PINDIR_D0_OUT_D1_IN) {
+ l &= ~OMAP2_MCSPI_CHCONF_IS;
+ l &= ~OMAP2_MCSPI_CHCONF_DPE1;
+ l |= OMAP2_MCSPI_CHCONF_DPE0;
+ } else {
+ l |= OMAP2_MCSPI_CHCONF_IS;
+ l |= OMAP2_MCSPI_CHCONF_DPE1;
+ l &= ~OMAP2_MCSPI_CHCONF_DPE0;
+ }
/* wordlength */
l &= ~OMAP2_MCSPI_CHCONF_WL_MASK;
@@ -1167,6 +1175,11 @@
master->cleanup = omap2_mcspi_cleanup;
master->dev.of_node = node;
+ dev_set_drvdata(&pdev->dev, master);
+
+ mcspi = spi_master_get_devdata(master);
+ mcspi->master = master;
+
match = of_match_device(omap_mcspi_of_match, &pdev->dev);
if (match) {
u32 num_cs = 1; /* default number of chipselect */
@@ -1175,19 +1188,17 @@
of_property_read_u32(node, "ti,spi-num-cs", &num_cs);
master->num_chipselect = num_cs;
master->bus_num = bus_num++;
+ if (of_get_property(node, "ti,pindir-d0-in-d1-out", NULL))
+ mcspi->pin_dir = MCSPI_PINDIR_D0_IN_D1_OUT;
} else {
pdata = pdev->dev.platform_data;
master->num_chipselect = pdata->num_cs;
if (pdev->id != -1)
master->bus_num = pdev->id;
+ mcspi->pin_dir = pdata->pin_dir;
}
regs_offset = pdata->regs_offset;
- dev_set_drvdata(&pdev->dev, master);
-
- mcspi = spi_master_get_devdata(master);
- mcspi->master = master;
-
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (r == NULL) {
status = -ENODEV;
