s2io: convert to net_device_ops
Convert this driver to network device ops. Compile teseted only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c
index 6236934..a464205 100644
--- a/drivers/net/s2io.c
+++ b/drivers/net/s2io.c
@@ -352,9 +352,10 @@
sp->def_mac_addr[offset].mac_addr[1] = (u8) (mac_addr >> 32);
sp->def_mac_addr[offset].mac_addr[0] = (u8) (mac_addr >> 40);
}
+
/* Add the vlan */
static void s2io_vlan_rx_register(struct net_device *dev,
- struct vlan_group *grp)
+ struct vlan_group *grp)
{
int i;
struct s2io_nic *nic = netdev_priv(dev);
@@ -372,7 +373,7 @@
}
/* Unregister the vlan */
-static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned long vid)
+static void s2io_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
{
int i;
struct s2io_nic *nic = netdev_priv(dev);
@@ -7717,6 +7718,24 @@
S2IO_BIT_RESET);
}
+static const struct net_device_ops s2io_netdev_ops = {
+ .ndo_open = s2io_open,
+ .ndo_stop = s2io_close,
+ .ndo_get_stats = s2io_get_stats,
+ .ndo_start_xmit = s2io_xmit,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_multicast_list = s2io_set_multicast,
+ .ndo_do_ioctl = s2io_ioctl,
+ .ndo_set_mac_address = s2io_set_mac_addr,
+ .ndo_change_mtu = s2io_change_mtu,
+ .ndo_vlan_rx_register = s2io_vlan_rx_register,
+ .ndo_vlan_rx_kill_vid = s2io_vlan_rx_kill_vid,
+ .ndo_tx_timeout = s2io_tx_watchdog,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = s2io_netpoll,
+#endif
+};
+
/**
* s2io_init_nic - Initialization of the adapter .
* @pdev : structure containing the PCI related information of the device.
@@ -7942,26 +7961,9 @@
}
/* Driver entry points */
- dev->open = &s2io_open;
- dev->stop = &s2io_close;
- dev->hard_start_xmit = &s2io_xmit;
- dev->get_stats = &s2io_get_stats;
- dev->set_multicast_list = &s2io_set_multicast;
- dev->do_ioctl = &s2io_ioctl;
- dev->set_mac_address = &s2io_set_mac_addr;
- dev->change_mtu = &s2io_change_mtu;
+ dev->netdev_ops = &s2io_netdev_ops;
SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
- dev->vlan_rx_register = s2io_vlan_rx_register;
- dev->vlan_rx_kill_vid = (void *)s2io_vlan_rx_kill_vid;
-
- /*
- * will use eth_mac_addr() for dev->set_mac_address
- * mac address will be set every time dev->open() is called
- */
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = s2io_netpoll;
-#endif
dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
if (sp->high_dma_flag == TRUE)
@@ -7972,7 +7974,6 @@
dev->features |= NETIF_F_UFO;
dev->features |= NETIF_F_HW_CSUM;
}
- dev->tx_timeout = &s2io_tx_watchdog;
dev->watchdog_timeo = WATCH_DOG_TIMEOUT;
INIT_WORK(&sp->rst_timer_task, s2io_restart_nic);
INIT_WORK(&sp->set_link_task, s2io_set_link);
