// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/*
 * Copyright (C) 2021 MediaTek Inc.
 */

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/spmi/spmi.h>
#include "mt8195.dtsi"
#include "mt6359.dtsi"

/ {
	aliases {
		i2c0 = &i2c0;
		i2c1 = &i2c1;
		i2c2 = &i2c2;
		i2c3 = &i2c3;
		i2c4 = &i2c4;
		i2c5 = &i2c5;
		i2c7 = &i2c7;
		mmc0 = &mmc0;
		mmc1 = &mmc1;
		serial0 = &uart0;
	};

	backlight_lcd0: backlight-lcd0 {
		compatible = "pwm-backlight";
		brightness-levels = <0 1023>;
		default-brightness-level = <576>;
		enable-gpios = <&pio 82 GPIO_ACTIVE_HIGH>;
		num-interpolated-steps = <1023>;
		pwms = <&disp_pwm0 0 500000>;
		power-supply = <&ppvar_sys>;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	dmic-codec {
		compatible = "dmic-codec";
		num-channels = <2>;
		wakeup-delay-ms = <50>;
	};

	memory@40000000 {
		device_type = "memory";
		reg = <0 0x40000000 0 0x80000000>;
	};

	pp3300_disp_x: regulator-pp3300-disp-x {
		compatible = "regulator-fixed";
		regulator-name = "pp3300_disp_x";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-enable-ramp-delay = <2500>;
		enable-active-high;
		gpio = <&pio 55 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&panel_fixed_pins>;
		vin-supply = <&pp3300_z2>;
	};

	/* system wide LDO 3.3V power rail */
	pp3300_z5: regulator-pp3300-ldo-z5 {
		compatible = "regulator-fixed";
		regulator-name = "pp3300_ldo_z5";
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		vin-supply = <&ppvar_sys>;
	};

	/* separately switched 3.3V power rail */
	pp3300_s3: regulator-pp3300-s3 {
		compatible = "regulator-fixed";
		regulator-name = "pp3300_s3";
		/* automatically sequenced by PMIC EXT_PMIC_EN2 */
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		vin-supply = <&pp3300_z2>;
	};

	/* system wide 3.3V power rail */
	pp3300_z2: regulator-pp3300-z2 {
		compatible = "regulator-fixed";
		regulator-name = "pp3300_z2";
		/* EN pin tied to pp4200_z2, which is controlled by EC */
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		vin-supply = <&ppvar_sys>;
	};

	/* system wide 4.2V power rail */
	pp4200_z2: regulator-pp4200-z2 {
		compatible = "regulator-fixed";
		regulator-name = "pp4200_z2";
		/* controlled by EC */
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <4200000>;
		regulator-max-microvolt = <4200000>;
		vin-supply = <&ppvar_sys>;
	};

	/* system wide switching 5.0V power rail */
	pp5000_s5: regulator-pp5000-s5 {
		compatible = "regulator-fixed";
		regulator-name = "pp5000_s5";
		/* controlled by EC */
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		vin-supply = <&ppvar_sys>;
	};

	/* system wide semi-regulated power rail from battery or USB */
	ppvar_sys: regulator-ppvar-sys {
		compatible = "regulator-fixed";
		regulator-name = "ppvar_sys";
		regulator-always-on;
		regulator-boot-on;
	};

	/* Murata NCP03WF104F05RL */
	tboard_thermistor1: thermal-sensor-t1 {
		compatible = "generic-adc-thermal";
		#thermal-sensor-cells = <0>;
		io-channels = <&auxadc 0>;
		io-channel-names = "sensor-channel";
		temperature-lookup-table = <	(-10000) 1553
						(-5000) 1485
						0 1406
						5000 1317
						10000 1219
						15000 1115
						20000 1007
						25000 900
						30000 796
						35000 697
						40000 605
						45000 523
						50000 449
						55000 384
						60000 327
						65000 279
						70000 237
						75000 202
						80000 172
						85000 147
						90000 125
						95000 107
						100000 92
						105000 79
						110000 68
						115000 59
						120000 51
						125000 44>;
	};

	tboard_thermistor2: thermal-sensor-t2 {
		compatible = "generic-adc-thermal";
		#thermal-sensor-cells = <0>;
		io-channels = <&auxadc 1>;
		io-channel-names = "sensor-channel";
		temperature-lookup-table = <	(-10000) 1553
						(-5000) 1485
						0 1406
						5000 1317
						10000 1219
						15000 1115
						20000 1007
						25000 900
						30000 796
						35000 697
						40000 605
						45000 523
						50000 449
						55000 384
						60000 327
						65000 279
						70000 237
						75000 202
						80000 172
						85000 147
						90000 125
						95000 107
						100000 92
						105000 79
						110000 68
						115000 59
						120000 51
						125000 44>;
	};

	usb_vbus: regulator-5v0-usb-vbus {
		compatible = "regulator-fixed";
		regulator-name = "usb-vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;
		regulator-always-on;
	};

	reserved_memory: reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		scp_mem: memory@50000000 {
			compatible = "shared-dma-pool";
			reg = <0 0x50000000 0 0x2900000>;
			no-map;
		};

		adsp_mem: memory@60000000 {
			compatible = "shared-dma-pool";
			reg = <0 0x60000000 0 0xd80000>;
			no-map;
		};

		afe_mem: memory@60d80000 {
			compatible = "shared-dma-pool";
			reg = <0 0x60d80000 0 0x100000>;
			no-map;
		};

		adsp_device_mem: memory@60e80000 {
			compatible = "shared-dma-pool";
			reg = <0 0x60e80000 0 0x280000>;
			no-map;
		};
	};

	spk_amplifier: rt1019p {
		compatible = "realtek,rt1019p";
		label = "rt1019p";
		pinctrl-names = "default";
		pinctrl-0 = <&rt1019p_pins_default>;
		sdb-gpios = <&pio 100 GPIO_ACTIVE_HIGH>;
	};
};

&adsp {
	status = "okay";

	memory-region = <&adsp_device_mem>, <&adsp_mem>;
};

&afe {
	status = "okay";

	mediatek,etdm-in2-cowork-source = <2>;
	mediatek,etdm-out2-cowork-source = <0>;
	memory-region = <&afe_mem>;
};

&auxadc {
	status = "okay";
};

&dp_intf0 {
	status = "okay";

	port {
		dp_intf0_out: endpoint {
			remote-endpoint = <&edp_in>;
		};
	};
};

&dp_intf1 {
	status = "okay";

	port {
		dp_intf1_out: endpoint {
			remote-endpoint = <&dptx_in>;
		};
	};
};

&edp_tx {
	status = "okay";

	pinctrl-names = "default";
	pinctrl-0 = <&edptx_pins_default>;

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
			reg = <0>;
			edp_in: endpoint {
				remote-endpoint = <&dp_intf0_out>;
			};
		};

		port@1 {
			reg = <1>;
			edp_out: endpoint {
				data-lanes = <0 1 2 3>;
				remote-endpoint = <&panel_in>;
			};
		};
	};

	aux-bus {
		panel {
			compatible = "edp-panel";
			power-supply = <&pp3300_disp_x>;
			backlight = <&backlight_lcd0>;
			port {
				panel_in: endpoint {
					remote-endpoint = <&edp_out>;
				};
			};
		};
	};
};

&disp_pwm0 {
	status = "okay";

	pinctrl-names = "default";
	pinctrl-0 = <&disp_pwm0_pin_default>;
};

&dp_tx {
	status = "okay";

	pinctrl-names = "default";
	pinctrl-0 = <&dptx_pin>;

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
			reg = <0>;
			dptx_in: endpoint {
				remote-endpoint = <&dp_intf1_out>;
			};
		};

		port@1 {
			reg = <1>;
			dptx_out: endpoint {
				data-lanes = <0 1 2 3>;
			};
		};
	};
};

&gic {
	mediatek,broken-save-restore-fw;
};

&gpu {
	status = "okay";
	mali-supply = <&mt6315_7_vbuck1>;
};

&i2c0 {
	status = "okay";

	clock-frequency = <400000>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c0_pins>;
};

&i2c1 {
	status = "okay";

	clock-frequency = <400000>;
	i2c-scl-internal-delay-ns = <12500>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_pins>;

	trackpad@15 {
		compatible = "elan,ekth3000";
		reg = <0x15>;
		interrupts-extended = <&pio 6 IRQ_TYPE_LEVEL_LOW>;
		pinctrl-names = "default";
		pinctrl-0 = <&trackpad_pins>;
		vcc-supply = <&pp3300_s3>;
		wakeup-source;
	};
};

&i2c2 {
	status = "okay";

	clock-frequency = <400000>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c2_pins>;

	audio_codec: codec@1a {
		/* Realtek RT5682i or RT5682s, sharing the same configuration */
		reg = <0x1a>;
		interrupts-extended = <&pio 89 IRQ_TYPE_EDGE_BOTH>;
		realtek,jd-src = <1>;

		AVDD-supply = <&mt6359_vio18_ldo_reg>;
		MICVDD-supply = <&pp3300_z2>;
		VBAT-supply = <&pp3300_z5>;
	};
};

&i2c3 {
	status = "okay";

	clock-frequency = <400000>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c3_pins>;

	tpm@50 {
		compatible = "google,cr50";
		reg = <0x50>;
		interrupts-extended = <&pio 88 IRQ_TYPE_EDGE_FALLING>;
		pinctrl-names = "default";
		pinctrl-0 = <&cr50_int>;
	};
};

&i2c4 {
	status = "okay";

	clock-frequency = <400000>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c4_pins>;

	ts_10: touchscreen@10 {
		compatible = "hid-over-i2c";
		reg = <0x10>;
		hid-descr-addr = <0x0001>;
		interrupts-extended = <&pio 92 IRQ_TYPE_LEVEL_LOW>;
		pinctrl-names = "default";
		pinctrl-0 = <&touchscreen_pins>;
		post-power-on-delay-ms = <10>;
		vdd-supply = <&pp3300_s3>;
		status = "disabled";
	};
};

&i2c5 {
	status = "okay";

	clock-frequency = <400000>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c5_pins>;
};

&i2c7 {
	status = "okay";

	clock-frequency = <400000>;
	pinctrl-names = "default";
	pinctrl-0 = <&i2c7_pins>;

	pmic@34 {
		#interrupt-cells = <2>;
		compatible = "mediatek,mt6360";
		reg = <0x34>;
		interrupt-controller;
		interrupts-extended = <&pio 130 IRQ_TYPE_EDGE_FALLING>;
		interrupt-names = "IRQB";
		pinctrl-names = "default";
		pinctrl-0 = <&subpmic_default>;
		wakeup-source;
	};
};

&mfg0 {
	domain-supply = <&mt6315_7_vbuck1>;
};

&mfg1 {
	domain-supply = <&mt6359_vsram_others_ldo_reg>;
};

&mmc0 {
	status = "okay";

	bus-width = <8>;
	cap-mmc-highspeed;
	cap-mmc-hw-reset;
	hs400-ds-delay = <0x14c11>;
	max-frequency = <200000000>;
	mmc-hs200-1_8v;
	mmc-hs400-1_8v;
	no-sdio;
	no-sd;
	non-removable;
	pinctrl-names = "default", "state_uhs";
	pinctrl-0 = <&mmc0_pins_default>;
	pinctrl-1 = <&mmc0_pins_uhs>;
	vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
	vqmmc-supply = <&mt6359_vufs_ldo_reg>;
};

&mmc1 {
	status = "okay";

	bus-width = <4>;
	cap-sd-highspeed;
	cd-gpios = <&pio 54 GPIO_ACTIVE_LOW>;
	max-frequency = <200000000>;
	no-mmc;
	no-sdio;
	pinctrl-names = "default", "state_uhs";
	pinctrl-0 = <&mmc1_pins_default>, <&mmc1_pins_detect>;
	pinctrl-1 = <&mmc1_pins_default>;
	sd-uhs-sdr50;
	sd-uhs-sdr104;
	vmmc-supply = <&mt_pmic_vmch_ldo_reg>;
	vqmmc-supply = <&mt_pmic_vmc_ldo_reg>;
};

&mt6359codec {
	mediatek,dmic-mode = <1>;  /* one-wire */
	mediatek,mic-type-0 = <2>; /* DMIC */
};

/* for CPU-L */
&mt6359_vcore_buck_reg {
	regulator-always-on;
};

/* for CORE */
&mt6359_vgpu11_buck_reg {
	regulator-always-on;
};

&mt6359_vgpu11_sshub_buck_reg {
	regulator-always-on;
	regulator-min-microvolt = <550000>;
	regulator-max-microvolt = <550000>;
};

/* for CORE SRAM */
&mt6359_vpu_buck_reg {
	regulator-always-on;
};

&mt6359_vrf12_ldo_reg {
	regulator-always-on;
};

/* for GPU SRAM */
&mt6359_vsram_others_ldo_reg {
	regulator-min-microvolt = <750000>;
	regulator-max-microvolt = <750000>;
};

&mt6359_vufs_ldo_reg {
	regulator-always-on;
};

&nor_flash {
	status = "okay";

	pinctrl-names = "default";
	pinctrl-0 = <&nor_pins_default>;

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <52000000>;
		spi-rx-bus-width = <2>;
		spi-tx-bus-width = <2>;
	};
};

&pcie1 {
	status = "okay";

	pinctrl-names = "default";
	pinctrl-0 = <&pcie1_pins_default>;
};

&pio {
	mediatek,rsel-resistance-in-si-unit;
	pinctrl-names = "default";
	pinctrl-0 = <&pio_default>;

	/* 144 lines */
	gpio-line-names =
		"I2S_SPKR_MCLK",
		"I2S_SPKR_DATAIN",
		"I2S_SPKR_LRCK",
		"I2S_SPKR_BCLK",
		"EC_AP_INT_ODL",
		/*
		 * AP_FLASH_WP_L is crossystem ABI. Schematics
		 * call it AP_FLASH_WP_ODL.
		 */
		"AP_FLASH_WP_L",
		"TCHPAD_INT_ODL",
		"EDP_HPD_1V8",
		"AP_I2C_CAM_SDA",
		"AP_I2C_CAM_SCL",
		"AP_I2C_TCHPAD_SDA_1V8",
		"AP_I2C_TCHPAD_SCL_1V8",
		"AP_I2C_AUD_SDA",
		"AP_I2C_AUD_SCL",
		"AP_I2C_TPM_SDA_1V8",
		"AP_I2C_TPM_SCL_1V8",
		"AP_I2C_TCHSCR_SDA_1V8",
		"AP_I2C_TCHSCR_SCL_1V8",
		"EC_AP_HPD_OD",
		"",
		"PCIE_NVME_RST_L",
		"PCIE_NVME_CLKREQ_ODL",
		"PCIE_RST_1V8_L",
		"PCIE_CLKREQ_1V8_ODL",
		"PCIE_WAKE_1V8_ODL",
		"CLK_24M_CAM0",
		"CAM1_SEN_EN",
		"AP_I2C_PWR_SCL_1V8",
		"AP_I2C_PWR_SDA_1V8",
		"AP_I2C_MISC_SCL",
		"AP_I2C_MISC_SDA",
		"EN_PP5000_HDMI_X",
		"AP_HDMITX_HTPLG",
		"",
		"AP_HDMITX_SCL_1V8",
		"AP_HDMITX_SDA_1V8",
		"AP_RTC_CLK32K",
		"AP_EC_WATCHDOG_L",
		"SRCLKENA0",
		"SRCLKENA1",
		"PWRAP_SPI0_CS_L",
		"PWRAP_SPI0_CK",
		"PWRAP_SPI0_MOSI",
		"PWRAP_SPI0_MISO",
		"SPMI_SCL",
		"SPMI_SDA",
		"",
		"",
		"",
		"I2S_HP_DATAIN",
		"I2S_HP_MCLK",
		"I2S_HP_BCK",
		"I2S_HP_LRCK",
		"I2S_HP_DATAOUT",
		"SD_CD_ODL",
		"EN_PP3300_DISP_X",
		"TCHSCR_RST_1V8_L",
		"TCHSCR_REPORT_DISABLE",
		"EN_PP3300_WLAN_X",
		"BT_KILL_1V8_L",
		"I2S_SPKR_DATAOUT",
		"WIFI_KILL_1V8_L",
		"BEEP_ON",
		"SCP_I2C_SENSOR_SCL_1V8",
		"SCP_I2C_SENSOR_SDA_1V8",
		"",
		"",
		"",
		"",
		"AUD_CLK_MOSI",
		"AUD_SYNC_MOSI",
		"AUD_DAT_MOSI0",
		"AUD_DAT_MOSI1",
		"AUD_DAT_MISO0",
		"AUD_DAT_MISO1",
		"AUD_DAT_MISO2",
		"SCP_VREQ_VAO",
		"AP_SPI_GSC_TPM_CLK",
		"AP_SPI_GSC_TPM_MOSI",
		"AP_SPI_GSC_TPM_CS_L",
		"AP_SPI_GSC_TPM_MISO",
		"EN_PP1000_CAM_X",
		"AP_EDP_BKLTEN",
		"",
		"USB3_HUB_RST_L",
		"",
		"WLAN_ALERT_ODL",
		"EC_IN_RW_ODL",
		"GSC_AP_INT_ODL",
		"HP_INT_ODL",
		"CAM0_RST_L",
		"CAM1_RST_L",
		"TCHSCR_INT_1V8_L",
		"CAM1_DET_L",
		"RST_ALC1011_L",
		"",
		"",
		"BL_PWM_1V8",
		"UART_AP_TX_DBG_RX",
		"UART_DBG_TX_AP_RX",
		"EN_SPKR",
		"AP_EC_WARM_RST_REQ",
		"UART_SCP_TX_DBGCON_RX",
		"UART_DBGCON_TX_SCP_RX",
		"",
		"",
		"KPCOL0",
		"",
		"MT6315_GPU_INT",
		"MT6315_PROC_BC_INT",
		"SD_CMD",
		"SD_CLK",
		"SD_DAT0",
		"SD_DAT1",
		"SD_DAT2",
		"SD_DAT3",
		"EMMC_DAT7",
		"EMMC_DAT6",
		"EMMC_DAT5",
		"EMMC_DAT4",
		"EMMC_RSTB",
		"EMMC_CMD",
		"EMMC_CLK",
		"EMMC_DAT3",
		"EMMC_DAT2",
		"EMMC_DAT1",
		"EMMC_DAT0",
		"EMMC_DSL",
		"",
		"",
		"MT6360_INT_ODL",
		"SCP_JTAG0_TRSTN",
		"AP_SPI_EC_CS_L",
		"AP_SPI_EC_CLK",
		"AP_SPI_EC_MOSI",
		"AP_SPI_EC_MISO",
		"SCP_JTAG0_TMS",
		"SCP_JTAG0_TCK",
		"SCP_JTAG0_TDO",
		"SCP_JTAG0_TDI",
		"AP_SPI_FLASH_CS_L",
		"AP_SPI_FLASH_CLK",
		"AP_SPI_FLASH_MOSI",
		"AP_SPI_FLASH_MISO";

	aud_pins_default: audio-default-pins {
		pins-cmd-dat {
		    pinmux = <PINMUX_GPIO69__FUNC_AUD_CLK_MOSI>,
			     <PINMUX_GPIO70__FUNC_AUD_SYNC_MOSI>,
			     <PINMUX_GPIO71__FUNC_AUD_DAT_MOSI0>,
			     <PINMUX_GPIO72__FUNC_AUD_DAT_MOSI1>,
			     <PINMUX_GPIO73__FUNC_AUD_DAT_MISO0>,
			     <PINMUX_GPIO74__FUNC_AUD_DAT_MISO1>,
			     <PINMUX_GPIO75__FUNC_AUD_DAT_MISO2>,
			     <PINMUX_GPIO0__FUNC_TDMIN_MCK>,
			     <PINMUX_GPIO1__FUNC_TDMIN_DI>,
			     <PINMUX_GPIO2__FUNC_TDMIN_LRCK>,
			     <PINMUX_GPIO3__FUNC_TDMIN_BCK>,
			     <PINMUX_GPIO60__FUNC_I2SO2_D0>,
			     <PINMUX_GPIO49__FUNC_I2SIN_D0>,
			     <PINMUX_GPIO50__FUNC_I2SO1_MCK>,
			     <PINMUX_GPIO51__FUNC_I2SO1_BCK>,
			     <PINMUX_GPIO52__FUNC_I2SO1_WS>,
			     <PINMUX_GPIO53__FUNC_I2SO1_D0>;
		};

		pins-hp-jack-int-odl {
			pinmux = <PINMUX_GPIO89__FUNC_GPIO89>;
			input-enable;
			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
		};
	};

	cr50_int: cr50-irq-default-pins {
		pins-gsc-ap-int-odl {
			pinmux = <PINMUX_GPIO88__FUNC_GPIO88>;
			input-enable;
		};
	};

	cros_ec_int: cros-ec-irq-default-pins {
		pins-ec-ap-int-odl {
			pinmux = <PINMUX_GPIO4__FUNC_GPIO4>;
			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
			input-enable;
		};
	};

	edptx_pins_default: edptx-default-pins {
		pins-cmd-dat {
			pinmux = <PINMUX_GPIO7__FUNC_EDP_TX_HPD>;
			bias-pull-up;
		};
	};

	disp_pwm0_pin_default: disp-pwm0-default-pins {
		pins-disp-pwm {
			pinmux = <PINMUX_GPIO82__FUNC_GPIO82>,
				 <PINMUX_GPIO97__FUNC_DISP_PWM0>;
		};
	};

	dptx_pin: dptx-default-pins {
		pins-cmd-dat {
			pinmux = <PINMUX_GPIO18__FUNC_DP_TX_HPD>;
			bias-pull-up;
		};
	};

	i2c0_pins: i2c0-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO8__FUNC_SDA0>,
				 <PINMUX_GPIO9__FUNC_SCL0>;
			bias-disable;
			drive-strength-microamp = <1000>;
		};
	};

	i2c1_pins: i2c1-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO10__FUNC_SDA1>,
				 <PINMUX_GPIO11__FUNC_SCL1>;
			bias-pull-up = <1000>;
			drive-strength-microamp = <1000>;
		};
	};

	i2c2_pins: i2c2-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO12__FUNC_SDA2>,
				 <PINMUX_GPIO13__FUNC_SCL2>;
			bias-disable;
			drive-strength-microamp = <1000>;
		};
	};

	i2c3_pins: i2c3-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO14__FUNC_SDA3>,
				 <PINMUX_GPIO15__FUNC_SCL3>;
			bias-pull-up = <1000>;
			drive-strength-microamp = <1000>;
		};
	};

	i2c4_pins: i2c4-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO16__FUNC_SDA4>,
				 <PINMUX_GPIO17__FUNC_SCL4>;
			bias-pull-up = <1000>;
			drive-strength = <4>;
		};
	};

	i2c5_pins: i2c5-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO29__FUNC_SCL5>,
				 <PINMUX_GPIO30__FUNC_SDA5>;
			bias-disable;
			drive-strength-microamp = <1000>;
		};
	};

	i2c7_pins: i2c7-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO27__FUNC_SCL7>,
				 <PINMUX_GPIO28__FUNC_SDA7>;
			bias-disable;
		};
	};

	mmc0_pins_default: mmc0-default-pins {
		pins-cmd-dat {
			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
			input-enable;
			drive-strength = <6>;
			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
		};

		pins-clk {
			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
			drive-strength = <6>;
			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
		};

		pins-rst {
			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
			drive-strength = <6>;
			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
		};
	};

	mmc0_pins_uhs: mmc0-uhs-pins {
		pins-cmd-dat {
			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
			input-enable;
			drive-strength = <8>;
			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
		};

		pins-clk {
			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
			drive-strength = <8>;
			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
		};

		pins-ds {
			pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
			drive-strength = <8>;
			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
		};

		pins-rst {
			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
			drive-strength = <8>;
			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
		};
	};

	mmc1_pins_detect: mmc1-detect-pins {
		pins-insert {
			pinmux = <PINMUX_GPIO54__FUNC_GPIO54>;
			bias-pull-up;
		};
	};

	mmc1_pins_default: mmc1-default-pins {
		pins-cmd-dat {
			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
			input-enable;
			drive-strength = <8>;
			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
		};

		pins-clk {
			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
			drive-strength = <8>;
			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
		};
	};

	nor_pins_default: nor-default-pins {
		pins-ck-io {
			pinmux = <PINMUX_GPIO142__FUNC_SPINOR_IO0>,
				 <PINMUX_GPIO141__FUNC_SPINOR_CK>,
				 <PINMUX_GPIO143__FUNC_SPINOR_IO1>;
			drive-strength = <6>;
			bias-pull-down;
		};

		pins-cs {
			pinmux = <PINMUX_GPIO140__FUNC_SPINOR_CS>;
			drive-strength = <6>;
			bias-pull-up;
		};
	};

	pcie0_pins_default: pcie0-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO19__FUNC_WAKEN>,
				 <PINMUX_GPIO20__FUNC_PERSTN>,
				 <PINMUX_GPIO21__FUNC_CLKREQN>;
				 bias-pull-up;
		};
	};

	pcie1_pins_default: pcie1-default-pins {
		pins-bus {
			pinmux = <PINMUX_GPIO22__FUNC_PERSTN_1>,
				 <PINMUX_GPIO23__FUNC_CLKREQN_1>,
				 <PINMUX_GPIO24__FUNC_WAKEN_1>;
				 bias-pull-up;
		};
	};

	panel_fixed_pins: panel-pwr-default-pins {
		pins-vreg-en {
			pinmux = <PINMUX_GPIO55__FUNC_GPIO55>;
		};
	};

	pio_default: pio-default-pins {
		pins-wifi-enable {
			pinmux = <PINMUX_GPIO58__FUNC_GPIO58>;
			output-high;
			drive-strength = <14>;
		};

		pins-low-power-pd {
			pinmux = <PINMUX_GPIO25__FUNC_GPIO25>,
				 <PINMUX_GPIO26__FUNC_GPIO26>,
				 <PINMUX_GPIO46__FUNC_GPIO46>,
				 <PINMUX_GPIO47__FUNC_GPIO47>,
				 <PINMUX_GPIO48__FUNC_GPIO48>,
				 <PINMUX_GPIO65__FUNC_GPIO65>,
				 <PINMUX_GPIO66__FUNC_GPIO66>,
				 <PINMUX_GPIO67__FUNC_GPIO67>,
				 <PINMUX_GPIO68__FUNC_GPIO68>,
				 <PINMUX_GPIO128__FUNC_GPIO128>,
				 <PINMUX_GPIO129__FUNC_GPIO129>;
			input-enable;
			bias-pull-down;
		};

		pins-low-power-pupd {
			pinmux = <PINMUX_GPIO77__FUNC_GPIO77>,
				 <PINMUX_GPIO78__FUNC_GPIO78>,
				 <PINMUX_GPIO79__FUNC_GPIO79>,
				 <PINMUX_GPIO80__FUNC_GPIO80>,
				 <PINMUX_GPIO83__FUNC_GPIO83>,
				 <PINMUX_GPIO85__FUNC_GPIO85>,
				 <PINMUX_GPIO90__FUNC_GPIO90>,
				 <PINMUX_GPIO91__FUNC_GPIO91>,
				 <PINMUX_GPIO93__FUNC_GPIO93>,
				 <PINMUX_GPIO94__FUNC_GPIO94>,
				 <PINMUX_GPIO95__FUNC_GPIO95>,
				 <PINMUX_GPIO96__FUNC_GPIO96>,
				 <PINMUX_GPIO104__FUNC_GPIO104>,
				 <PINMUX_GPIO105__FUNC_GPIO105>,
				 <PINMUX_GPIO107__FUNC_GPIO107>;
			input-enable;
			bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
		};
	};

	rt1019p_pins_default: rt1019p-default-pins {
		pins-amp-sdb {
			pinmux = <PINMUX_GPIO100__FUNC_GPIO100>;
			output-low;
		};
	};

	scp_pins: scp-default-pins {
		pins-vreq {
			pinmux = <PINMUX_GPIO76__FUNC_SCP_VREQ_VAO>;
			bias-disable;
			input-enable;
		};
	};

	spi0_pins: spi0-default-pins {
		pins-cs-mosi-clk {
			pinmux = <PINMUX_GPIO132__FUNC_SPIM0_CSB>,
				 <PINMUX_GPIO134__FUNC_SPIM0_MO>,
				 <PINMUX_GPIO133__FUNC_SPIM0_CLK>;
			bias-disable;
		};

		pins-miso {
			pinmux = <PINMUX_GPIO135__FUNC_SPIM0_MI>;
			bias-pull-down;
		};
	};

	subpmic_default: subpmic-default-pins {
		subpmic_pin_irq: pins-subpmic-int-n {
			pinmux = <PINMUX_GPIO130__FUNC_GPIO130>;
			input-enable;
			bias-pull-up;
		};
	};

	trackpad_pins: trackpad-default-pins {
		pins-int-n {
			pinmux = <PINMUX_GPIO6__FUNC_GPIO6>;
			input-enable;
			bias-pull-up;
		};
	};

	touchscreen_pins: touchscreen-default-pins {
		pins-int-n {
			pinmux = <PINMUX_GPIO92__FUNC_GPIO92>;
			input-enable;
			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
		};
		pins-rst {
			pinmux = <PINMUX_GPIO56__FUNC_GPIO56>;
			output-high;
		};
		pins-report-sw {
			pinmux = <PINMUX_GPIO57__FUNC_GPIO57>;
			output-low;
		};
	};
};

&pmic {
	interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
};

&scp {
	status = "okay";

	firmware-name = "mediatek/mt8195/scp.img";
	memory-region = <&scp_mem>;
	pinctrl-names = "default";
	pinctrl-0 = <&scp_pins>;

	cros-ec-rpmsg {
		compatible = "google,cros-ec-rpmsg";
		mediatek,rpmsg-name = "cros-ec-rpmsg";
	};
};

&sound {
	status = "okay";

	mediatek,adsp = <&adsp>;
	mediatek,dai-link =
		"DL10_FE", "DPTX_BE", "ETDM1_IN_BE", "ETDM2_IN_BE",
		"ETDM1_OUT_BE", "ETDM2_OUT_BE","UL_SRC1_BE",
		"AFE_SOF_DL2", "AFE_SOF_DL3", "AFE_SOF_UL4", "AFE_SOF_UL5";
	pinctrl-names = "default";
	pinctrl-0 = <&aud_pins_default>;
};

&spi0 {
	status = "okay";

	pinctrl-names = "default";
	pinctrl-0 = <&spi0_pins>;
	mediatek,pad-select = <0>;

	cros_ec: ec@0 {
		#address-cells = <1>;
		#size-cells = <0>;

		compatible = "google,cros-ec-spi";
		reg = <0>;
		interrupts-extended = <&pio 4 IRQ_TYPE_LEVEL_LOW>;
		pinctrl-names = "default";
		pinctrl-0 = <&cros_ec_int>;
		spi-max-frequency = <3000000>;
		wakeup-source;

		keyboard-backlight {
			compatible = "google,cros-kbd-led-backlight";
		};

		i2c_tunnel: i2c-tunnel {
			compatible = "google,cros-ec-i2c-tunnel";
			google,remote-bus = <0>;
			#address-cells = <1>;
			#size-cells = <0>;
		};

		mt_pmic_vmc_ldo_reg: regulator@0 {
			compatible = "google,cros-ec-regulator";
			reg = <0>;
			regulator-name = "mt_pmic_vmc_ldo";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <3600000>;
		};

		mt_pmic_vmch_ldo_reg: regulator@1 {
			compatible = "google,cros-ec-regulator";
			reg = <1>;
			regulator-name = "mt_pmic_vmch_ldo";
			regulator-min-microvolt = <2700000>;
			regulator-max-microvolt = <3600000>;
		};

		typec {
			compatible = "google,cros-ec-typec";
			#address-cells = <1>;
			#size-cells = <0>;

			usb_c0: connector@0 {
				compatible = "usb-c-connector";
				reg = <0>;
				power-role = "dual";
				data-role = "host";
				try-power-role = "source";
			};

			usb_c1: connector@1 {
				compatible = "usb-c-connector";
				reg = <1>;
				power-role = "dual";
				data-role = "host";
				try-power-role = "source";
			};
		};
	};
};

&spmi {
	#address-cells = <2>;
	#size-cells = <0>;

	mt6315@6 {
		compatible = "mediatek,mt6315-regulator";
		reg = <0x6 SPMI_USID>;

		regulators {
			mt6315_6_vbuck1: vbuck1 {
				regulator-compatible = "vbuck1";
				regulator-name = "Vbcpu";
				regulator-min-microvolt = <300000>;
				regulator-max-microvolt = <1193750>;
				regulator-enable-ramp-delay = <256>;
				regulator-ramp-delay = <6250>;
				regulator-allowed-modes = <0 1 2>;
				regulator-always-on;
			};
		};
	};

	mt6315@7 {
		compatible = "mediatek,mt6315-regulator";
		reg = <0x7 SPMI_USID>;

		regulators {
			mt6315_7_vbuck1: vbuck1 {
				regulator-compatible = "vbuck1";
				regulator-name = "Vgpu";
				regulator-min-microvolt = <625000>;
				regulator-max-microvolt = <1193750>;
				regulator-enable-ramp-delay = <256>;
				regulator-ramp-delay = <6250>;
				regulator-allowed-modes = <0 1 2>;
			};
		};
	};
};

&thermal_zones {
	soc-area-thermal {
		polling-delay = <1000>;
		polling-delay-passive = <250>;
		thermal-sensors = <&tboard_thermistor1>;

		trips {
			trip-crit {
				temperature = <84000>;
				hysteresis = <1000>;
				type = "critical";
			};
		};
	};

	pmic-area-thermal {
		polling-delay = <1000>;
		polling-delay-passive = <0>;
		thermal-sensors = <&tboard_thermistor2>;

		trips {
			trip-crit {
				temperature = <84000>;
				hysteresis = <1000>;
				type = "critical";
			};
		};
	};
};

&u3phy0 {
	status = "okay";
};

&u3phy1 {
	status = "okay";
};

&u3phy2 {
	status = "okay";
};

&u3phy3 {
	status = "okay";
};

&uart0 {
	status = "okay";
};

/*
 * For the USB Type-C ports the role and alternate modes switching is
 * done by the EC so we set dr_mode to host to avoid interfering.
 */
&ssusb0 {
	dr_mode = "host";
	vusb33-supply = <&mt6359_vusb_ldo_reg>;
	status = "okay";
};

&ssusb2 {
	dr_mode = "host";
	vusb33-supply = <&mt6359_vusb_ldo_reg>;
	status = "okay";
};

&ssusb3 {
	dr_mode = "host";
	vusb33-supply = <&mt6359_vusb_ldo_reg>;
	status = "okay";
};

&xhci0 {
	status = "okay";

	rx-fifo-depth = <3072>;
	vbus-supply = <&usb_vbus>;
};

&xhci1 {
	status = "okay";

	rx-fifo-depth = <3072>;
	vusb33-supply = <&mt6359_vusb_ldo_reg>;
	vbus-supply = <&usb_vbus>;
};

&xhci2 {
	status = "okay";
	vbus-supply = <&usb_vbus>;
};

&xhci3 {
	status = "okay";

	/* MT7921's USB Bluetooth has issues with USB2 LPM */
	usb2-lpm-disable;
	vbus-supply = <&usb_vbus>;
};

#include <arm/cros-ec-keyboard.dtsi>
#include <arm/cros-ec-sbs.dtsi>

&keyboard_controller {
	function-row-physmap = <
		MATRIX_KEY(0x00, 0x02, 0)	/* T1 */
		MATRIX_KEY(0x03, 0x02, 0)	/* T2 */
		MATRIX_KEY(0x02, 0x02, 0)	/* T3 */
		MATRIX_KEY(0x01, 0x02, 0)	/* T4 */
		MATRIX_KEY(0x03, 0x04, 0)	/* T5 */
		MATRIX_KEY(0x02, 0x04, 0)	/* T6 */
		MATRIX_KEY(0x01, 0x04, 0)	/* T7 */
		MATRIX_KEY(0x02, 0x09, 0)	/* T8 */
		MATRIX_KEY(0x01, 0x09, 0)	/* T9 */
		MATRIX_KEY(0x00, 0x04, 0)	/* T10 */
	>;

	linux,keymap = <
		MATRIX_KEY(0x00, 0x02, KEY_BACK)
		MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
		MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
		MATRIX_KEY(0x01, 0x02, KEY_SCALE)
		MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
		MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
		MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
		MATRIX_KEY(0x02, 0x09, KEY_MUTE)
		MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
		MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)

		CROS_STD_MAIN_KEYMAP
	>;
};