// SPDX-License-Identifier: ISC
/*
 * Device Tree file for Netgear WG302v2 based on IXP422BB
 * Derived from boardfiles written by Imre Kaloz
 */

/dts-v1/;

#include "intel-ixp42x.dtsi"
#include <dt-bindings/input/input.h>

/ {
	model = "Netgear WG302 v2";
	compatible = "netgear,wg302v2", "intel,ixp42x";
	#address-cells = <1>;
	#size-cells = <1>;

	memory@0 {
		/* 16 MB SDRAM according to OpenWrt database */
		device_type = "memory";
		reg = <0x00000000 0x01000000>;
	};

	chosen {
		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
		stdout-path = "uart1:115200n8";
	};

	aliases {
		/* These are switched around */
		serial0 = &uart1;
		serial1 = &uart0;
	};

	soc {
		bus@c4000000 {
			flash@0,0 {
				compatible = "intel,ixp4xx-flash", "cfi-flash";
				bank-width = <2>;
				/*
				 * 32 MB of Flash in 128 0x20000 sized blocks
				 * mapped in at CS0 and CS1
				 */
				reg = <0 0x00000000 0x2000000>;

				/* Configure expansion bus to allow writes */
				intel,ixp4xx-eb-write-enable = <1>;

				partitions {
					compatible = "redboot-fis";
					/* CHECKME: guess this is Redboot FIS */
					fis-index-block = <0xff>;
				};
			};
		};

		pci@c0000000 {
			status = "ok";

			/*
			 * Taken from WG302 v2 PCI boardfile (wg302v2-pci.c)
			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
			 * each handling all IRQs.
			 */
			#interrupt-cells = <1>;
			interrupt-map-mask = <0xf800 0 0 7>;
			interrupt-map =
			/* IDSEL 1 */
			<0x0800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 8 */
			<0x0800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 8 */
			<0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */
			<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
			/* IDSEL 2 */
			<0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */
			<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
			<0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */
			<0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */
		};

		ethernet@c8009000 {
			status = "ok";
			queue-rx = <&qmgr 3>;
			queue-txready = <&qmgr 20>;
			phy-mode = "rgmii";
			phy-handle = <&phy8>;

			mdio {
				#address-cells = <1>;
				#size-cells = <0>;

				phy8: ethernet-phy@8 {
					reg = <8>;
				};
			};
		};
	};
};