| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Support for CompuLab CM-T3530 |
| */ |
| /dts-v1/; |
| |
| #include "omap34xx.dtsi" |
| #include "omap3-cm-t3x30.dtsi" |
| |
| / { |
| model = "CompuLab CM-T3530"; |
| compatible = "compulab,omap3-cm-t3530", "ti,omap3430", "ti,omap34xx", "ti,omap3"; |
| |
| /* Regulator to trigger the reset signal of the Wifi module */ |
| mmc2_sdio_reset: regulator-mmc2-sdio-reset { |
| compatible = "regulator-fixed"; |
| regulator-name = "regulator-mmc2-sdio-reset"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| mmc2_pins: pinmux_mmc2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ |
| OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ |
| OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ |
| OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ |
| OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ |
| OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ |
| OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */ |
| OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */ |
| OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */ |
| OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ |
| >; |
| }; |
| }; |
| |
| &mmc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_pins>; |
| vmmc-supply = <&mmc2_sdio_reset>; |
| non-removable; |
| bus-width = <4>; |
| cap-power-off-card; |
| }; |
| |
| &dss { |
| status = "okay"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = < |
| &dss_dpi_pins_common |
| &dss_dpi_pins_cm_t35x |
| >; |
| }; |
| |
