blob: 52160e3683049aa83e4c106e8506a04a87691fef [file] [log] [blame]
/*
* Copyright 2013 Oliver Schinagl
*
* Oliver Schinagl <oliver@schinagl.nl>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun7i-a20.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "Cubietech Cubietruck";
compatible = "cubietech,cubietruck", "allwinner,sun7i-a20";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
led-0 {
label = "cubietruck:blue:usr";
gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
};
led-1 {
label = "cubietruck:orange:usr";
gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
};
led-2 {
label = "cubietruck:white:usr";
gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>;
};
led-3 {
label = "cubietruck:green:usr";
gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>;
};
};
mmc3_pwrseq: mmc3_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
clocks = <&ccu CLK_OUT_A>;
clock-names = "ext_clock";
};
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "On-board SPDIF";
simple-audio-card,cpu {
sound-dai = <&spdif>;
};
simple-audio-card,codec {
sound-dai = <&spdif_out>;
};
};
spdif_out: spdif-out {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
};
};
&ahci {
target-supply = <&reg_ahci_5v>;
status = "okay";
};
&codec {
status = "okay";
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&gmac {
pinctrl-names = "default";
pinctrl-0 = <&gmac_rgmii_pins>;
phy-handle = <&phy1>;
phy-mode = "rgmii-id";
status = "okay";
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&i2c0 {
status = "okay";
axp209: pmic@34 {
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
};
};
&i2c1 {
pinctrl-names = "default";
status = "okay";
};
&i2c2 {
status = "okay";
};
&ir0 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&gmac_mdio {
phy1: ethernet-phy@1 {
reg = <1>;
};
};
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
&mmc3 {
vmmc-supply = <&reg_vcc3v3>;
mmc-pwrseq = <&mmc3_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
interrupts = <7 10 IRQ_TYPE_LEVEL_LOW>; /* PH10 / EINT10 */
interrupt-names = "host-wake";
};
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&otg_sram {
status = "okay";
};
&pio {
/* Pin outputs low power clock for WiFi and BT */
pinctrl-0 = <&clk_out_a_pin>;
pinctrl-names = "default";
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pin>, <&pwm1_pin>;
status = "okay";
};
&reg_ahci_5v {
gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
status = "okay";
};
#include "axp209.dtsi"
&ac_power_supply {
status = "okay";
};
&battery_power_supply {
status = "okay";
};
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1450000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-int-dll";
};
&reg_ldo1 {
regulator-name = "vdd-rtc";
};
&reg_ldo2 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
&reg_usb0_vbus {
gpio = <&pio 7 17 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&reg_usb1_vbus {
status = "okay";
};
&reg_usb2_vbus {
status = "okay";
};
&spdif {
pinctrl-names = "default";
pinctrl-0 = <&spdif_tx_pin>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pi_pins>, <&uart2_cts_rts_pi_pins>;
uart-has-rtscts;
status = "okay";
bluetooth {
compatible = "brcm,bcm20702a1";
clocks = <&ccu CLK_OUT_A>;
clock-names = "lpo";
device-wakeup-gpios = <&pio 7 24 GPIO_ACTIVE_LOW>; /* PH24 */
host-wakeup-gpios = <&pio 7 25 GPIO_ACTIVE_LOW>; /* PH25 */
shutdown-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
max-speed = <1500000>;
};
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usbphy {
usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <&reg_usb0_vbus>;
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};