blob: 422958d13d42f1f5033b96ef65254e8d2ab882fa [file] [log] [blame]
/*
* Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
* Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "orion5x-mv88f5182.dtsi"
/ {
model = "LaCie d2 Network";
compatible = "lacie,d2-network", "marvell,orion5x-88f5182", "marvell,orion5x";
memory {
device_type = "memory";
reg = <0x00000000 0x4000000>; /* 64 MB */
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
stdout-path = &uart0;
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
<MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
<MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>;
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&pmx_buttons>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
front_button {
label = "Front Push Button";
linux,code = <KEY_POWER>;
gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
};
power_rocker_sw_on {
label = "Power rocker switch (on|auto)";
linux,input-type = <5>; /* EV_SW */
linux,code = <1>; /* D2NET_SWITCH_POWER_ON */
gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
};
power_rocker_sw_off {
label = "Power rocker switch (auto|off)";
linux,input-type = <5>; /* EV_SW */
linux,code = <2>; /* D2NET_SWITCH_POWER_OFF */
gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&pmx_sata0_power &pmx_sata1_power>;
pinctrl-names = "default";
sata0_power: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "SATA0 Power";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
regulator-boot-on;
gpio = <&gpio0 3 GPIO_ACTIVE_HIGH>;
};
sata1_power: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "SATA1 Power";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
regulator-boot-on;
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
};
};
};
&devbus_bootcs {
status = "okay";
devbus,keep-config;
/*
* Currently the MTD code does not recognize the MX29LV400CBCT
* as a bottom-type device. This could cause risks of
* accidentally erasing critical flash sectors. We thus define
* a single, write-protected partition covering the whole
* flash. TODO: once the flash part TOP/BOTTOM detection
* issue is sorted out in the MTD code, break this into at
* least three partitions: 'u-boot code', 'u-boot environment'
* and 'whatever is left'.
*/
flash@0 {
compatible = "cfi-flash";
reg = <0 0x80000>;
bank-width = <1>;
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "Full512Kb";
reg = <0 0x80000>;
read-only;
};
};
};
&mdio {
status = "okay";
ethphy: ethernet-phy {
reg = <8>;
};
};
&ehci0 {
status = "okay";
};
&eth {
status = "okay";
ethernet-port@0 {
phy-handle = <&ethphy>;
};
};
&i2c {
status = "okay";
clock-frequency = <100000>;
#address-cells = <1>;
rtc@32 {
compatible = "ricoh,rs5c372b";
reg = <0x32>;
};
fan@3e {
compatible = "gmt,g762";
reg = <0x3e>;
/* Not enough HW info */
status = "disabled";
};
eeprom@50 {
compatible = "atmel,24c08";
reg = <0x50>;
};
};
&pinctrl {
pinctrl-0 = <&pmx_leds &pmx_board_id &pmx_fan_fail>;
pinctrl-names = "default";
pmx_board_id: pmx-board-id {
marvell,pins = "mpp0", "mpp1", "mpp2";
marvell,function = "gpio";
};
pmx_buttons: pmx-buttons {
marvell,pins = "mpp8", "mpp9", "mpp18";
marvell,function = "gpio";
};
pmx_fan_fail: pmx-fan-fail {
marvell,pins = "mpp5";
marvell,function = "gpio";
};
/*
* MPP6: Red front LED
* MPP16: Blue front LED blink control
*/
pmx_leds: pmx-leds {
marvell,pins = "mpp6", "mpp16";
marvell,function = "gpio";
};
pmx_sata0_led_active: pmx-sata0-led-active {
marvell,pins = "mpp14";
marvell,function = "sata0";
};
pmx_sata0_power: pmx-sata0-power {
marvell,pins = "mpp3";
marvell,function = "gpio";
};
pmx_sata1_led_active: pmx-sata1-led-active {
marvell,pins = "mpp15";
marvell,function = "sata1";
};
pmx_sata1_power: pmx-sata1-power {
marvell,pins = "mpp12";
marvell,function = "gpio";
};
/*
* Non MPP GPIOs:
* GPIO 22: USB port 1 fuse (0 = Fail, 1 = Ok)
* GPIO 23: Blue front LED off
* GPIO 24: Inhibit board power off (0 = Disabled, 1 = Enabled)
*/
};
&sata {
pinctrl-0 = <&pmx_sata0_led_active
&pmx_sata1_led_active>;
pinctrl-names = "default";
status = "okay";
nr-ports = <2>;
};
&uart0 {
status = "okay";
};