#
# Multifunction miscellaneous devices
#

if HAS_IOMEM
menu "Multifunction device drivers"

config MFD_CORE
	tristate
	select IRQ_DOMAIN
	default n

config MFD_CS5535
	tristate "AMD CS5535 and CS5536 southbridge core functions"
	select MFD_CORE
	depends on PCI && (X86_32 || (X86 && COMPILE_TEST))
	---help---
	  This is the core driver for CS5535/CS5536 MFD functions.  This is
          necessary for using the board's GPIO and MFGPT functionality.

config MFD_ALTERA_A10SR
	bool "Altera Arria10 DevKit System Resource chip"
	depends on ARCH_SOCFPGA && SPI_MASTER=y && OF
	select REGMAP_SPI
	select MFD_CORE
	help
	  Support for the Altera Arria10 DevKit MAX5 System Resource chip
	  using the SPI interface. This driver provides common support for
	  accessing the external gpio extender (LEDs & buttons) and
	  power supply alarms (hwmon).

config MFD_ACT8945A
	tristate "Active-semi ACT8945A"
	select MFD_CORE
	select REGMAP_I2C
	depends on I2C && OF
	help
	  Support for the ACT8945A PMIC from Active-semi. This device
	  features three step-down DC/DC converters and four low-dropout
	  linear regulators, along with a complete ActivePath battery
	  charger.

config MFD_SUN4I_GPADC
	tristate "Allwinner sunxi platforms' GPADC MFD driver"
	select MFD_CORE
	select REGMAP_MMIO
	select REGMAP_IRQ
	depends on ARCH_SUNXI || COMPILE_TEST
	depends on !TOUCHSCREEN_SUN4I
	help
	  Select this to get support for Allwinner SoCs (A10, A13 and A31) ADC.
	  This driver will only map the hardware interrupt and registers, you
	  have to select individual drivers based on this MFD to be able to use
	  the ADC or the thermal sensor. This will try to probe the ADC driver
	  sun4i-gpadc-iio and the hwmon driver iio_hwmon.

	  To compile this driver as a module, choose M here: the module will be
	  called sun4i-gpadc.

config MFD_AS3711
	bool "AMS AS3711"
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	depends on I2C=y
	help
	  Support for the AS3711 PMIC from AMS

config MFD_AS3722
	tristate "ams AS3722 Power Management IC"
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	depends on I2C=y && OF
	help
	  The ams AS3722 is a compact system PMU suitable for mobile phones,
	  tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down
	  controllers, 11 LDOs, RTC, automatic battery, temperature and
	  over current monitoring, GPIOs, ADC and a watchdog.

config PMIC_ADP5520
	bool "Analog Devices ADP5520/01 MFD PMIC Core Support"
	depends on I2C=y
	help
	  Say yes here to add support for Analog Devices AD5520 and ADP5501,
	  Multifunction Power Management IC. This includes
	  the I2C driver and the core APIs _only_, you have to select
	  individual components like LCD backlight, LEDs, GPIOs and Kepad
	  under the corresponding menus.

config MFD_AAT2870_CORE
	bool "AnalogicTech AAT2870"
	select MFD_CORE
	depends on I2C=y
	depends on GPIOLIB || COMPILE_TEST
	help
	  If you say yes here you get support for the AAT2870.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

config MFD_AT91_USART
	tristate "AT91 USART Driver"
	select MFD_CORE
	depends on ARCH_AT91 || COMPILE_TEST
	help
	  Select this to get support for AT91 USART IP. This is a wrapper
	  over at91-usart-serial driver and usart-spi-driver. Only one function
	  can be used at a time. The choice is done at boot time by the probe
	  function of this MFD driver according to a device tree property.

config MFD_ATMEL_FLEXCOM
	tristate "Atmel Flexcom (Flexible Serial Communication Unit)"
	select MFD_CORE
	depends on OF
	help
	  Select this to get support for Atmel Flexcom. This is a wrapper
	  which embeds a SPI controller, a I2C controller and a USART. Only
	  one function can be used at a time. The choice is done at boot time
	  by the probe function of this MFD driver according to a device tree
	  property.

config MFD_ATMEL_HLCDC
	tristate "Atmel HLCDC (High-end LCD Controller)"
	select MFD_CORE
	select REGMAP_MMIO
	depends on OF
	help
	  If you say yes here you get support for the HLCDC block.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

config MFD_ATMEL_SMC
	bool
	select MFD_SYSCON

config MFD_BCM590XX
	tristate "Broadcom BCM590xx PMUs"
	select MFD_CORE
	select REGMAP_I2C
	depends on I2C
	help
	  Support for the BCM590xx PMUs from Broadcom

config MFD_BD9571MWV
	tristate "ROHM BD9571MWV PMIC"
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	depends on I2C
	help
	  Support for the ROHM BD9571MWV PMIC, which contains single
	  voltage regulator, voltage sampling units, GPIO block and
	  watchdog block.

	  This driver can also be built as a module. If so, the module
	  will be called bd9571mwv.

config MFD_AC100
	tristate "X-Powers AC100"
	select MFD_CORE
	depends on SUNXI_RSB
	help
	  If you say Y here you get support for the X-Powers AC100 audio codec
	  IC.
	  This driver include only the core APIs. You have to select individual
	  components like codecs or RTC under the corresponding menus.

config MFD_AXP20X
	tristate
	select MFD_CORE
	select REGMAP_IRQ

config MFD_AXP20X_I2C
	tristate "X-Powers AXP series PMICs with I2C"
	select MFD_AXP20X
	select REGMAP_I2C
	depends on I2C
	help
	  If you say Y here you get support for the X-Powers AXP series power
	  management ICs (PMICs) controlled with I2C.
	  This driver include only the core APIs. You have to select individual
	  components like regulators or the PEK (Power Enable Key) under the
	  corresponding menus.

	  Note on x86 this provides an ACPI OpRegion, so this must be 'y'
	  (builtin) and not a module, as the OpRegion must be available as
	  soon as possible. For the same reason the I2C bus driver options
	  I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_BAYTRAIL must be 'y' too.

config MFD_AXP20X_RSB
	tristate "X-Powers AXP series PMICs with RSB"
	select MFD_AXP20X
	depends on SUNXI_RSB
	help
	  If you say Y here you get support for the X-Powers AXP series power
	  management ICs (PMICs) controlled with RSB.
	  This driver include only the core APIs. You have to select individual
	  components like regulators or the PEK (Power Enable Key) under the
	  corresponding menus.

config MFD_CROS_EC
	tristate "ChromeOS Embedded Controller"
	select MFD_CORE
	select CHROME_PLATFORMS
	select CROS_EC_PROTO
	depends on X86 || ARM || ARM64 || COMPILE_TEST
	help
	  If you say Y here you get support for the ChromeOS Embedded
	  Controller (EC) providing keyboard, battery and power services.
	  You also need to enable the driver for the bus you are using. The
	  protocol for talking to the EC is defined by the bus driver.

config MFD_CROS_EC_CHARDEV
        tristate "Chrome OS Embedded Controller userspace device interface"
        depends on MFD_CROS_EC
        ---help---
          This driver adds support to talk with the ChromeOS EC from userspace.

          If you have a supported Chromebook, choose Y or M here.
          The module will be called cros_ec_dev.

config MFD_MADERA
	tristate "Cirrus Logic Madera codecs"
	select MFD_CORE
	select REGMAP
	select REGMAP_IRQ
	select MADERA_IRQ
	select PINCTRL
	select PINCTRL_MADERA
	help
	  Support for the Cirrus Logic Madera platform audio codecs

config MFD_MADERA_I2C
	tristate "Cirrus Logic Madera codecs with I2C"
	depends on MFD_MADERA
	depends on I2C
	select REGMAP_I2C
	help
	  Support for the Cirrus Logic Madera platform audio SoC
	  core functionality controlled via I2C.

config MFD_MADERA_SPI
	tristate "Cirrus Logic Madera codecs with SPI"
	depends on MFD_MADERA
	depends on SPI_MASTER
	select REGMAP_SPI
	help
	  Support for the Cirrus Logic Madera platform audio SoC
	  core functionality controlled via SPI.

config MFD_CS47L35
	bool "Cirrus Logic CS47L35"
	select PINCTRL_CS47L35
	depends on MFD_MADERA
	help
	  Support for Cirrus Logic CS47L35 Smart Codec

config MFD_CS47L85
	bool "Cirrus Logic CS47L85"
	select PINCTRL_CS47L85
	depends on MFD_MADERA
	help
	  Support for Cirrus Logic CS47L85 Smart Codec

config MFD_CS47L90
	bool "Cirrus Logic CS47L90/91"
	select PINCTRL_CS47L90
	depends on MFD_MADERA
	help
	  Support for Cirrus Logic CS47L90 and CS47L91 Smart Codecs

config MFD_ASIC3
	bool "Compaq ASIC3"
	depends on GPIOLIB && ARM
	select MFD_CORE
	 ---help---
	  This driver supports the ASIC3 multifunction chip found on many
	  PDAs (mainly iPAQ and HTC based ones)

config PMIC_DA903X
	bool "Dialog Semiconductor DA9030/DA9034 PMIC Support"
	depends on I2C=y
	help
	  Say yes here to add support for Dialog Semiconductor DA9030 (a.k.a
	  ARAVA) and DA9034 (a.k.a MICCO), these are Power Management IC
	  usually found on PXA processors-based platforms. This includes
	  the I2C driver and the core APIs _only_, you have to select
	  individual components like LCD backlight, voltage regulators,
	  LEDs and battery-charger under the corresponding menus.

config PMIC_DA9052
	bool
	select MFD_CORE

config MFD_DA9052_SPI
	bool "Dialog Semiconductor DA9052/53 PMIC variants with SPI"
	select REGMAP_SPI
	select REGMAP_IRQ
	select PMIC_DA9052
	depends on SPI_MASTER=y
	help
	  Support for the Dialog Semiconductor DA9052 PMIC
	  when controlled using SPI. This driver provides common support
	  for accessing the device, additional drivers must be enabled in
	  order to use the functionality of the device.

config MFD_DA9052_I2C
	bool "Dialog Semiconductor DA9052/53 PMIC variants with I2C"
	select REGMAP_I2C
	select REGMAP_IRQ
	select PMIC_DA9052
	depends on I2C=y
	help
	  Support for the Dialog Semiconductor DA9052 PMIC
	  when controlled using I2C. This driver provides common support
	  for accessing the device, additional drivers must be enabled in
	  order to use the functionality of the device.

config MFD_DA9055
	bool "Dialog Semiconductor DA9055 PMIC Support"
	select REGMAP_I2C
	select REGMAP_IRQ
	select MFD_CORE
	depends on I2C=y
	help
	  Say yes here for support of Dialog Semiconductor DA9055. This is
	  a Power Management IC. This driver provides common support for
	  accessing the device as well as the I2C interface to the chip itself.
	  Additional drivers must be enabled in order to use the functionality
	  of the device.

	  This driver can be built as a module. If built as a module it will be
	  called "da9055"

config MFD_DA9062
	tristate "Dialog Semiconductor DA9062/61 PMIC Support"
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	depends on I2C
	help
	  Say yes here for support for the Dialog Semiconductor DA9061 and
	  DA9062 PMICs.
	  This includes the I2C driver and core APIs.
	  Additional drivers must be enabled in order to use the functionality
	  of the device.

config MFD_DA9063
	tristate "Dialog Semiconductor DA9063 PMIC Support"
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	depends on I2C
	help
	  Say yes here for support for the Dialog Semiconductor DA9063 PMIC.
	  This includes the I2C driver and core APIs.
	  Additional drivers must be enabled in order to use the functionality
	  of the device.

config MFD_DA9150
	tristate "Dialog Semiconductor DA9150 Charger Fuel-Gauge chip"
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  This adds support for the DA9150 integrated charger and fuel-gauge
	  chip. This driver provides common support for accessing the device.
	  Additional drivers must be enabled in order to use the specific
	  features of the device.

config MFD_DLN2
	tristate "Diolan DLN2 support"
	select MFD_CORE
	depends on USB
	help
	  This adds support for Diolan USB-I2C/SPI/GPIO Master Adapter
	  DLN-2. Additional drivers such as I2C_DLN2, GPIO_DLN2,
	  etc. must be enabled in order to use the functionality of
	  the device.

config MFD_EXYNOS_LPASS
	tristate "Samsung Exynos SoC Low Power Audio Subsystem"
	depends on ARCH_EXYNOS || COMPILE_TEST
	select MFD_CORE
	select REGMAP_MMIO
	help
	  Select this option to enable support for Samsung Exynos Low Power
	  Audio Subsystem.

config MFD_MC13XXX
	tristate
	depends on (SPI_MASTER || I2C)
	select MFD_CORE
	select REGMAP_IRQ
	help
	  Enable support for the Freescale MC13783 and MC13892 PMICs.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

config MFD_MC13XXX_SPI
	tristate "Freescale MC13783 and MC13892 SPI interface"
	depends on SPI_MASTER
	select REGMAP_SPI
	select MFD_MC13XXX
	help
	  Select this if your MC13xxx is connected via an SPI bus.

config MFD_MC13XXX_I2C
	tristate "Freescale MC13892 I2C interface"
	depends on I2C
	select REGMAP_I2C
	select MFD_MC13XXX
	help
	  Select this if your MC13xxx is connected via an I2C bus.

config MFD_MXS_LRADC
	tristate "Freescale i.MX23/i.MX28 LRADC"
	depends on ARCH_MXS || COMPILE_TEST
	select MFD_CORE
	select STMP_DEVICE
	help
	  Say yes here to build support for the Low Resolution
	  Analog-to-Digital Converter (LRADC) found on the i.MX23 and i.MX28
	  processors. This driver provides common support for accessing the
	  device, additional drivers must be enabled in order to use the
	  functionality of the device:
		mxs-lradc-adc for ADC readings
		mxs-lradc-ts  for touchscreen support

	  This driver can also be built as a module. If so, the module will be
	  called mxs-lradc.

config MFD_MX25_TSADC
	tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
	select REGMAP_MMIO
	depends on (SOC_IMX25 && OF) || COMPILE_TEST
	help
	  Enable support for the integrated Touchscreen and ADC unit of the
	  i.MX25 processors. They consist of a conversion queue for general
	  purpose ADC and a queue for Touchscreens.

config MFD_HI6421_PMIC
	tristate "HiSilicon Hi6421 PMU/Codec IC"
	depends on OF
	select MFD_CORE
	select REGMAP_MMIO
	help
	  Add support for HiSilicon Hi6421 PMIC. Hi6421 includes multi-
	  functions, such as regulators, RTC, codec, Coulomb counter, etc.
	  This driver includes core APIs _only_. You have to select
	  individul components like voltage regulators under corresponding
	  menus in order to enable them.
	  We communicate with the Hi6421 via memory-mapped I/O.

config MFD_HI655X_PMIC
	tristate "HiSilicon Hi655X series PMU/Codec IC"
	depends on ARCH_HISI || COMPILE_TEST
	depends on OF
	select MFD_CORE
	select REGMAP_MMIO
	select REGMAP_IRQ
	help
	  Select this option to enable Hisilicon hi655x series pmic driver.

config HTC_PASIC3
	tristate "HTC PASIC3 LED/DS1WM chip support"
	select MFD_CORE
	help
	  This core driver provides register access for the LED/DS1WM
	  chips labeled "AIC2" and "AIC3", found on HTC Blueangel and
	  HTC Magician devices, respectively. Actual functionality is
	  handled by the leds-pasic3 and ds1wm drivers.

config HTC_I2CPLD
	bool "HTC I2C PLD chip support"
	depends on I2C=y && GPIOLIB
	help
	  If you say yes here you get support for the supposed CPLD
	  found on omap850 HTC devices like the HTC Wizard and HTC Herald.
	  This device provides input and output GPIOs through an I2C
	  interface to one or more sub-chips.

config MFD_INTEL_QUARK_I2C_GPIO
	tristate "Intel Quark MFD I2C GPIO"
	depends on PCI
	depends on X86
	depends on COMMON_CLK
	select MFD_CORE
	help
	  This MFD provides support for I2C and GPIO that exist only
	  in a single PCI device. It splits the 2 IO devices to
	  their respective IO driver.
	  The GPIO exports a total amount of 8 interrupt-capable GPIOs.

config LPC_ICH
	tristate "Intel ICH LPC"
	depends on PCI
	select MFD_CORE
	help
	  The LPC bridge function of the Intel ICH provides support for
	  many functional units. This driver provides needed support for
	  other drivers to control these functions, currently GPIO and
	  watchdog.

config LPC_SCH
	tristate "Intel SCH LPC"
	depends on PCI
	select MFD_CORE
	help
	  LPC bridge function of the Intel SCH provides support for
	  System Management Bus and General Purpose I/O.

config INTEL_SOC_PMIC
	bool "Support for Crystal Cove PMIC"
	depends on ACPI && HAS_IOMEM && I2C=y && GPIOLIB && COMMON_CLK
	depends on X86 || COMPILE_TEST
	depends on I2C_DESIGNWARE_PLATFORM=y
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  Select this option to enable support for Crystal Cove PMIC
	  on some Intel SoC systems. The PMIC provides ADC, GPIO,
	  thermal, charger and related power management functions
	  on these systems.

	  This option is a bool as it provides an ACPI OpRegion which must be
	  available before any devices using it are probed. This option also
	  causes the designware-i2c driver to be builtin for the same reason.

config INTEL_SOC_PMIC_BXTWC
	tristate "Support for Intel Broxton Whiskey Cove PMIC"
	depends on INTEL_PMC_IPC
	select MFD_CORE
	select REGMAP_IRQ
	help
	  Select this option to enable support for Whiskey Cove PMIC
	  on Intel Broxton systems. The PMIC provides ADC, GPIO,
	  thermal, charger and related power management functions
	  on these systems.

config INTEL_SOC_PMIC_CHTWC
	bool "Support for Intel Cherry Trail Whiskey Cove PMIC"
	depends on ACPI && HAS_IOMEM && I2C=y && COMMON_CLK
	depends on X86 || COMPILE_TEST
	depends on I2C_DESIGNWARE_PLATFORM=y
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  Select this option to enable support for the Intel Cherry Trail
	  Whiskey Cove PMIC found on some Intel Cherry Trail systems.

	  This option is a bool as it provides an ACPI OpRegion which must be
	  available before any devices using it are probed. This option also
	  causes the designware-i2c driver to be builtin for the same reason.

config INTEL_SOC_PMIC_CHTDC_TI
	tristate "Support for Intel Cherry Trail Dollar Cove TI PMIC"
	depends on GPIOLIB
	depends on I2C
	depends on ACPI
	depends on X86
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  Select this option for supporting Dollar Cove (TI version) PMIC
	  device that is found on some Intel Cherry Trail systems.

config MFD_INTEL_LPSS
	tristate
	select COMMON_CLK
	select MFD_CORE

config MFD_INTEL_LPSS_ACPI
	tristate "Intel Low Power Subsystem support in ACPI mode"
	select MFD_INTEL_LPSS
	depends on X86 && ACPI
	help
	  This driver supports Intel Low Power Subsystem (LPSS) devices such as
	  I2C, SPI and HS-UART starting from Intel Sunrisepoint (Intel Skylake
	  PCH) in ACPI mode.

config MFD_INTEL_LPSS_PCI
	tristate "Intel Low Power Subsystem support in PCI mode"
	select MFD_INTEL_LPSS
	depends on X86 && PCI
	help
	  This driver supports Intel Low Power Subsystem (LPSS) devices such as
	  I2C, SPI and HS-UART starting from Intel Sunrisepoint (Intel Skylake
	  PCH) in PCI mode.

config MFD_INTEL_MSIC
	bool "Intel MSIC"
	depends on INTEL_SCU_IPC
	select MFD_CORE
	help
	  Select this option to enable access to Intel MSIC (Avatele
	  Passage) chip. This chip embeds audio, battery, GPIO, etc.
	  devices used in Intel Medfield platforms.

config MFD_IPAQ_MICRO
	bool "Atmel Micro ASIC (iPAQ h3100/h3600/h3700) Support"
	depends on SA1100_H3100 || SA1100_H3600
	select MFD_CORE
	help
	  Select this to get support for the Microcontroller found in
	  the Compaq iPAQ handheld computers. This is an Atmel
	  AT90LS8535 microcontroller flashed with a special iPAQ
	  firmware using the custom protocol implemented in this driver.

config MFD_JANZ_CMODIO
	tristate "Janz CMOD-IO PCI MODULbus Carrier Board"
	select MFD_CORE
	depends on PCI
	help
	  This is the core driver for the Janz CMOD-IO PCI MODULbus
	  carrier board. This device is a PCI to MODULbus bridge which may
	  host many different types of MODULbus daughterboards, including
	  CAN and GPIO controllers.

config MFD_JZ4740_ADC
	bool "Janz JZ4740 ADC core"
	select MFD_CORE
	select GENERIC_IRQ_CHIP
	depends on MACH_JZ4740
	help
	  Say yes here if you want support for the ADC unit in the JZ4740 SoC.
	  This driver is necessary for jz4740-battery and jz4740-hwmon driver.

config MFD_KEMPLD
	tristate "Kontron module PLD device"
	select MFD_CORE
	help
	  This is the core driver for the PLD (Programmable Logic Device) found
	  on some Kontron ETX and COMexpress (ETXexpress) modules. The PLD
	  device may provide functions like watchdog, GPIO, UART and I2C bus.

	  The following modules are supported:
		* COMe-bBD#
		* COMe-bBL6
		* COMe-bHL6
		* COMe-bSL6
		* COMe-bIP#
		* COMe-bKL6
		* COMe-bPC2 (ETXexpress-PC)
		* COMe-bSC# (ETXexpress-SC T#)
		* COMe-cAL6
		* COMe-cBL6
		* COMe-cBT6
		* COMe-cBW6
		* COMe-cCT6
		* COMe-cDC2 (microETXexpress-DC)
		* COMe-cHL6
		* COMe-cKL6
		* COMe-cPC2 (microETXexpress-PC)
		* COMe-cSL6
		* COMe-mAL10
		* COMe-mBT10
		* COMe-mCT10
		* COMe-mTT10 (nanoETXexpress-TT)
		* ETX-OH

	  This driver can also be built as a module. If so, the module
	  will be called kempld-core.

config MFD_88PM800
	tristate "Marvell 88PM800"
	depends on I2C
	select REGMAP_I2C
	select REGMAP_IRQ
	select MFD_CORE
	help
	  This supports for Marvell 88PM800 Power Management IC.
	  This includes the I2C driver and the core APIs _only_, you have to
	  select individual components like voltage regulators, RTC and
	  battery-charger under the corresponding menus.

config MFD_88PM805
	tristate "Marvell 88PM805"
	depends on I2C
	select REGMAP_I2C
	select REGMAP_IRQ
	select MFD_CORE
	help
	  This supports for Marvell 88PM805 Power Management IC. This includes
	  the I2C driver and the core APIs _only_, you have to select individual
	  components like codec device, headset/Mic device under the
	  corresponding menus.

config MFD_88PM860X
	bool "Marvell 88PM8606/88PM8607"
	depends on I2C=y
	select REGMAP_I2C
	select MFD_CORE
	help
	  This supports for Marvell 88PM8606/88PM8607 Power Management IC.
	  This includes the I2C driver and the core APIs _only_, you have to
	  select individual components like voltage regulators, RTC and
	  battery-charger under the corresponding menus.

config MFD_MAX14577
	tristate "Maxim Semiconductor MAX14577/77836 MUIC + Charger Support"
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	select IRQ_DOMAIN
	help
	  Say yes here to add support for Maxim Semiconductor MAX14577 and
	  MAX77836 Micro-USB ICs with battery charger.
	  This driver provides common support for accessing the device;
	  additional drivers must be enabled in order to use the functionality
	  of the device.

config MFD_MAX77620
	bool "Maxim Semiconductor MAX77620 and MAX20024 PMIC Support"
	depends on I2C=y
	depends on OF || COMPILE_TEST
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	select IRQ_DOMAIN
	help
	  Say yes here to add support for Maxim Semiconductor MAX77620 and
	  MAX20024 which are Power Management IC with General purpose pins,
	  RTC, regulators, clock generator, watchdog etc. This driver
	  provides common support for accessing the device; additional drivers
	  must be enabled in order to use the functionality of the device.

config MFD_MAX77686
	tristate "Maxim Semiconductor MAX77686/802 PMIC Support"
	depends on I2C
	depends on OF || COMPILE_TEST
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	select IRQ_DOMAIN
	help
	  Say yes here to add support for Maxim Semiconductor MAX77686 and
	  MAX77802 which are Power Management IC with an RTC on chip.
	  This driver provides common support for accessing the device;
	  additional drivers must be enabled in order to use the functionality
	  of the device.

config MFD_MAX77693
	tristate "Maxim Semiconductor MAX77693 PMIC Support"
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  Say yes here to add support for Maxim Semiconductor MAX77693.
	  This is a companion Power Management IC with Flash, Haptic, Charger,
	  and MUIC(Micro USB Interface Controller) controls on chip.
	  This driver provides common support for accessing the device;
	  additional drivers must be enabled in order to use the functionality
	  of the device.

config MFD_MAX77843
	bool "Maxim Semiconductor MAX77843 PMIC Support"
	depends on I2C=y
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  Say yes here to add support for Maxim Semiconductor MAX77843.
	  This is companion Power Management IC with LEDs, Haptic, Charger,
	  Fuel Gauge, MUIC(Micro USB Interface Controller) controls on chip.
	  This driver provides common support for accessing the device;
	  additional drivers must be enabled in order to use the functionality
	  of the device.

config MFD_MAX8907
	tristate "Maxim Semiconductor MAX8907 PMIC Support"
	select MFD_CORE
	depends on I2C
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  Say yes here to add support for Maxim Semiconductor MAX8907. This is
	  a Power Management IC. This driver provides common support for
	  accessing the device; additional drivers must be enabled in order
	  to use the functionality of the device.

config MFD_MAX8925
	bool "Maxim Semiconductor MAX8925 PMIC Support"
	depends on I2C=y
	select MFD_CORE
	help
	  Say yes here to add support for Maxim Semiconductor MAX8925. This is
	  a Power Management IC. This driver provides common support for
	  accessing the device, additional drivers must be enabled in order
	  to use the functionality of the device.

config MFD_MAX8997
	bool "Maxim Semiconductor MAX8997/8966 PMIC Support"
	depends on I2C=y
	select MFD_CORE
	select IRQ_DOMAIN
	help
	  Say yes here to add support for Maxim Semiconductor MAX8997/8966.
	  This is a Power Management IC with RTC, Flash, Fuel Gauge, Haptic,
	  MUIC controls on chip.
	  This driver provides common support for accessing the device;
	  additional drivers must be enabled in order to use the functionality
	  of the device.

config MFD_MAX8998
	bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support"
	depends on I2C=y
	select MFD_CORE
	select IRQ_DOMAIN
	help
	  Say yes here to add support for Maxim Semiconductor MAX8998 and
	  National Semiconductor LP3974. This is a Power Management IC.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the functionality
	  of the device.

config MFD_MT6397
	tristate "MediaTek MT6397 PMIC Support"
	select MFD_CORE
	select IRQ_DOMAIN
	help
	  Say yes here to add support for MediaTek MT6397 PMIC. This is
	  a Power Management IC. This driver provides common support for
	  accessing the device; additional drivers must be enabled in order
	  to use the functionality of the device.

config MFD_MENF21BMC
	tristate "MEN 14F021P00 Board Management Controller Support"
	depends on I2C
	select MFD_CORE
	help
	  Say yes here to add support for the MEN 14F021P00 BMC
	  which is a Board Management Controller connected to the I2C bus.
	  The device supports multiple sub-devices like LED, HWMON and WDT.
	  This driver provides common support for accessing the devices;
	  additional drivers must be enabled in order to use the
	  functionality of the BMC device.

	  This driver can also be built as a module. If so the module
	  will be called menf21bmc.

config EZX_PCAP
	bool "Motorola EZXPCAP Support"
	depends on SPI_MASTER
	help
	  This enables the PCAP ASIC present on EZX Phones. This is
	  needed for MMC, TouchScreen, Sound, USB, etc..

config MFD_CPCAP
	tristate "Support for Motorola CPCAP"
	depends on SPI
	depends on OF || COMPILE_TEST
	select REGMAP_SPI
	select REGMAP_IRQ
	help
	  Say yes here if you want to include driver for CPCAP.
	  It is used on many Motorola phones and tablets as a PMIC.
	  At least Motorola Droid 4 is known to use CPCAP.

config MFD_VIPERBOARD
        tristate "Nano River Technologies Viperboard"
	select MFD_CORE
	depends on USB
	default n
	help
	  Say yes here if you want support for Nano River Technologies
	  Viperboard.
	  There are mfd cell drivers available for i2c master, adc and
	  both gpios found on the board. The spi part does not yet
	  have a driver.
	  You need to select the mfd cell drivers separately.
	  The drivers do not support all features the board exposes.

config MFD_RETU
	tristate "Nokia Retu and Tahvo multi-function device"
	select MFD_CORE
	depends on I2C
	select REGMAP_IRQ
	help
	  Retu and Tahvo are a multi-function devices found on Nokia
	  Internet Tablets (770, N800 and N810).

config MFD_PCF50633
	tristate "NXP PCF50633"
	depends on I2C
	select REGMAP_I2C
	help
	  Say yes here if you have NXP PCF50633 chip on your board.
	  This core driver provides register access and IRQ handling
	  facilities, and registers devices for the various functions
	  so that function-specific drivers can bind to them.

config PCF50633_ADC
	tristate "NXP PCF50633 ADC"
	depends on MFD_PCF50633
	help
	 Say yes here if you want to include support for ADC in the
	 NXP PCF50633 chip.

config PCF50633_GPIO
	tristate "NXP PCF50633 GPIO"
	depends on MFD_PCF50633
	help
	 Say yes here if you want to include support GPIO for pins on
	 the PCF50633 chip.

config UCB1400_CORE
	tristate "Philips UCB1400 Core driver"
	depends on AC97_BUS
	depends on GPIOLIB
	help
	  This enables support for the Philips UCB1400 core functions.
	  The UCB1400 is an AC97 audio codec.

	  To compile this driver as a module, choose M here: the
	  module will be called ucb1400_core.

config MFD_PM8XXX
	tristate "Qualcomm PM8xxx PMIC chips driver"
	depends on (ARM || HEXAGON || COMPILE_TEST)
	select IRQ_DOMAIN
	select MFD_CORE
	select REGMAP
	help
	  If you say yes to this option, support will be included for the
	  built-in PM8xxx PMIC chips.

	  This is required if your board has a PM8xxx and uses its features,
	  such as: MPPs, GPIOs, regulators, interrupts, and PWM.

	  Say M here if you want to include support for PM8xxx chips as a
	  module. This will build a module called "pm8xxx-core".

config MFD_QCOM_RPM
	tristate "Qualcomm Resource Power Manager (RPM)"
	depends on ARCH_QCOM && OF
	help
	  If you say yes to this option, support will be included for the
	  Resource Power Manager system found in the Qualcomm 8660, 8960 and
	  8064 based devices.

	  This is required to access many regulators, clocks and bus
	  frequencies controlled by the RPM on these devices.

	  Say M here if you want to include support for the Qualcomm RPM as a
	  module. This will build a module called "qcom_rpm".

config MFD_SPMI_PMIC
	tristate "Qualcomm SPMI PMICs"
	depends on ARCH_QCOM || COMPILE_TEST
	depends on OF
	depends on SPMI
	select REGMAP_SPMI
	help
	  This enables support for the Qualcomm SPMI PMICs.
	  These PMICs are currently used with the Snapdragon 800 series of
	  SoCs.  Note, that this will only be useful paired with descriptions
	  of the independent functions as children nodes in the device tree.

	  Say M here if you want to include support for the SPMI PMIC
	  series as a module.  The module will be called "qcom-spmi-pmic".

config MFD_RDC321X
	tristate "RDC R-321x southbridge"
	select MFD_CORE
	depends on PCI
	help
	  Say yes here if you want to have support for the RDC R-321x SoC
	  southbridge which provides access to GPIOs and Watchdog using the
	  southbridge PCI device configuration space.

config MFD_RT5033
	tristate "Richtek RT5033 Power Management IC"
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  This driver provides for the Richtek RT5033 Power Management IC,
	  which includes the I2C driver and the Core APIs. This driver provides
	  common support for accessing the device. The device supports multiple
	  sub-devices like charger, fuel gauge, flash LED, current source,
	  LDO and Buck.

config MFD_RC5T583
	bool "Ricoh RC5T583 Power Management system device"
	depends on I2C=y
	select MFD_CORE
	select REGMAP_I2C
	help
	  Select this option to get support for the RICOH583 Power
	  Management system device.
	  This driver provides common support for accessing the device
	  through i2c interface. The device supports multiple sub-devices
	  like GPIO, interrupts, RTC, LDO and DCDC regulators, onkey.
	  Additional drivers must be enabled in order to use the
	  different functionality of the device.

config MFD_RK808
	tristate "Rockchip RK805/RK808/RK818 Power Management Chip"
	depends on I2C && OF
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  If you say yes here you get support for the RK805, RK808 and RK818
	  Power Management chips.
	  This driver provides common support for accessing the device
	  through I2C interface. The device supports multiple sub-devices
	  including interrupts, RTC, LDO & DCDC regulators, and onkey.

config MFD_RN5T618
	tristate "Ricoh RN5T567/618 PMIC"
	depends on I2C
	depends on OF
	select MFD_CORE
	select REGMAP_I2C
	help
	  Say yes here to add support for the Ricoh RN5T567,
          RN5T618, RC5T619 PMIC.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

config MFD_SEC_CORE
	tristate "SAMSUNG Electronics PMIC Series Support"
	depends on I2C=y
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  Support for the Samsung Electronics PMIC devices coming
	  usually along with Samsung Exynos SoC chipset.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the functionality
	  of the device

	  To compile this driver as a module, choose M here: the
	  module will be called sec-core.
	  Have in mind that important core drivers (like regulators) depend
	  on this driver so building this as a module might require proper
	  initial ramdisk or might not boot up as well in certain scenarios.

config MFD_SI476X_CORE
	tristate "Silicon Laboratories 4761/64/68 AM/FM radio."
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	help
	  This is the core driver for the SI476x series of AM/FM
	  radio. This MFD driver connects the radio-si476x V4L2 module
	  and the si476x audio codec.

	  To compile this driver as a module, choose M here: the
	  module will be called si476x-core.

config MFD_SM501
	tristate "Silicon Motion SM501"
	 ---help---
	  This is the core driver for the Silicon Motion SM501 multimedia
	  companion chip. This device is a multifunction device which may
	  provide numerous interfaces including USB host controller, USB gadget,
	  asynchronous serial ports, audio functions, and a dual display video
	  interface. The device may be connected by PCI or local bus with
	  varying functions enabled.

config MFD_SM501_GPIO
	bool "Export GPIO via GPIO layer"
	depends on MFD_SM501 && GPIOLIB
	 ---help---
	 This option uses the gpio library layer to export the 64 GPIO
	 lines on the SM501. The platform data is used to supply the
	 base number for the first GPIO line to register.

config MFD_SKY81452
	tristate "Skyworks Solutions SKY81452"
	select MFD_CORE
	select REGMAP_I2C
	depends on I2C
	help
	  This is the core driver for the Skyworks SKY81452 backlight and
	  voltage regulator device.

	  This driver can also be built as a module.  If so, the module
	  will be called sky81452.

config MFD_SMSC
       bool "SMSC ECE1099 series chips"
       depends on I2C=y
       select MFD_CORE
       select REGMAP_I2C
       help
        If you say yes here you get support for the
        ece1099 chips from SMSC.

        To compile this driver as a module, choose M here: the
        module will be called smsc.

config MFD_SC27XX_PMIC
	tristate "Spreadtrum SC27xx PMICs"
	depends on ARCH_SPRD || COMPILE_TEST
	depends on SPI_MASTER
	select MFD_CORE
	select REGMAP_SPI
	select REGMAP_IRQ
	help
	  This enables support for the Spreadtrum SC27xx PMICs with SPI
	  interface. The SC27xx series PMICs integrate power management,
	  audio codec, battery management and user interface support
	  function (such as RTC, Typec, indicator and so on) in a single chip.

	  This driver provides common support for accessing the SC27xx PMICs,
	  and it also adds the irq_chip parts for handling the PMIC chip events.

config ABX500_CORE
	bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"
	default y if ARCH_U300 || ARCH_U8500 || COMPILE_TEST
	help
	  Say yes here if you have the ABX500 Mixed Signal IC family
	  chips. This core driver expose register access functions.
	  Functionality specific drivers using these functions can
	  remain unchanged when IC changes. Binding of the functions to
	  actual register access is done by the IC core driver.

config AB3100_CORE
	bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
	depends on I2C=y && ABX500_CORE
	select MFD_CORE
	default y if ARCH_U300
	help
	  Select this to enable the AB3100 Mixed Signal IC core
	  functionality. This connects to a AB3100 on the I2C bus
	  and expose a number of symbols needed for dependent devices
	  to read and write registers and subscribe to events from
	  this multi-functional IC. This is needed to use other features
	  of the AB3100 such as battery-backed RTC, charging control,
	  LEDs, vibrator, system power and temperature, power management
	  and ALSA sound.

config AB3100_OTP
	tristate "ST-Ericsson AB3100 OTP functions"
	depends on AB3100_CORE
	default y if AB3100_CORE
	help
	  Select this to enable the AB3100 Mixed Signal IC OTP (one-time
	  programmable memory) support. This exposes a sysfs file to read
	  out OTP values.

config AB8500_CORE
	bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
	depends on ABX500_CORE && MFD_DB8500_PRCMU
	select POWER_SUPPLY
	select MFD_CORE
	select IRQ_DOMAIN
	help
	  Select this option to enable access to AB8500 power management
	  chip. This connects to U8500 either on the SSP/SPI bus (deprecated
	  since hardware version v1.0) or the I2C bus via PRCMU. It also adds
	  the irq_chip parts for handling the Mixed Signal chip events.
	  This chip embeds various other multimedia funtionalities as well.

config AB8500_DEBUG
       bool "Enable debug info via debugfs"
       depends on AB8500_GPADC && DEBUG_FS
       default y if DEBUG_FS
       help
         Select this option if you want debug information using the debug
         filesystem, debugfs.

config AB8500_GPADC
	bool "ST-Ericsson AB8500 GPADC driver"
	depends on AB8500_CORE && REGULATOR_AB8500
	default y
	help
	  AB8500 GPADC driver used to convert Acc and battery/ac/usb voltage

config MFD_DB8500_PRCMU
	bool "ST-Ericsson DB8500 Power Reset Control Management Unit"
	depends on UX500_SOC_DB8500
	select MFD_CORE
	help
	  Select this option to enable support for the DB8500 Power Reset
	  and Control Management Unit. This is basically an autonomous
	  system controller running an XP70 microprocessor, which is accessed
	  through a register map.

config MFD_STMPE
	bool "STMicroelectronics STMPE"
	depends on (I2C=y || SPI_MASTER=y)
	depends on OF
	select MFD_CORE
	help
	  Support for the STMPE family of I/O Expanders from
	  STMicroelectronics.

	  Currently supported devices are:

		STMPE811: GPIO, Touchscreen, ADC
		STMPE1601: GPIO, Keypad
		STMPE1801: GPIO, Keypad
		STMPE2401: GPIO, Keypad
		STMPE2403: GPIO, Keypad

	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the functionality
	  of the device.  Currently available sub drivers are:

		GPIO: stmpe-gpio
		Keypad: stmpe-keypad
		Touchscreen: stmpe-ts
		ADC: stmpe-adc

menu "STMicroelectronics STMPE Interface Drivers"
depends on MFD_STMPE

config STMPE_I2C
	bool "STMicroelectronics STMPE I2C Interface"
	depends on I2C=y
	default y
	help
	  This is used to enable I2C interface of STMPE

config STMPE_SPI
	bool "STMicroelectronics STMPE SPI Interface"
	depends on SPI_MASTER
	help
	  This is used to enable SPI interface of STMPE
endmenu

config MFD_STA2X11
	bool "STMicroelectronics STA2X11"
	depends on STA2X11
	select MFD_CORE
	select REGMAP_MMIO

config MFD_SUN6I_PRCM
	bool "Allwinner A31 PRCM controller"
	depends on ARCH_SUNXI
	select MFD_CORE
	help
	  Support for the PRCM (Power/Reset/Clock Management) unit available
	  in A31 SoC.

config MFD_SYSCON
	bool "System Controller Register R/W Based on Regmap"
	select REGMAP_MMIO
	help
	  Select this option to enable accessing system control registers
	  via regmap.

config MFD_DAVINCI_VOICECODEC
	tristate
	select MFD_CORE
	select REGMAP_MMIO

config MFD_TI_AM335X_TSCADC
	tristate "TI ADC / Touch Screen chip support"
	select MFD_CORE
	select REGMAP
	select REGMAP_MMIO
	help
	  If you say yes here you get support for Texas Instruments series
	  of Touch Screen /ADC chips.
	  To compile this driver as a module, choose M here: the
	  module will be called ti_am335x_tscadc.

config MFD_DM355EVM_MSP
	bool "TI DaVinci DM355 EVM microcontroller"
	depends on I2C=y && MACH_DAVINCI_DM355_EVM
	help
	  This driver supports the MSP430 microcontroller used on these
	  boards.  MSP430 firmware manages resets and power sequencing,
	  inputs from buttons and the IR remote, LEDs, an RTC, and more.

config MFD_LP3943
	tristate "TI/National Semiconductor LP3943 MFD Driver"
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	help
	  Support for the TI/National Semiconductor LP3943.
	  This driver consists of GPIO and PWM drivers.
	  With these functionalities, it can be used for LED string control or
	  general usage such like a GPIO controller and a PWM controller.

config MFD_LP8788
	bool "TI LP8788 Power Management Unit Driver"
	depends on I2C=y
	select MFD_CORE
	select REGMAP_I2C
	select IRQ_DOMAIN
	help
	  TI LP8788 PMU supports regulators, battery charger, RTC,
	  ADC, backlight driver and current sinks.

config MFD_TI_LMU
	tristate "TI Lighting Management Unit driver"
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	help
	  Say yes here to enable support for TI LMU chips.

	  TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
	  It consists of backlight, LED and regulator driver.
	  It provides consistent device controls for lighting functions.

config MFD_OMAP_USB_HOST
	bool "TI OMAP USBHS core and TLL driver"
	depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3
	default y
	help
	  This is the core driver for the OAMP EHCI and OHCI drivers.
	  This MFD driver does the required setup functionalities for
	  OMAP USB Host drivers.

config MFD_PALMAS
	bool "TI Palmas series chips"
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	depends on I2C=y
	help
	  If you say yes here you get support for the Palmas
	  series of PMIC chips from Texas Instruments.

config TPS6105X
	tristate "TI TPS61050/61052 Boost Converters"
	depends on I2C
	select REGMAP_I2C
	select REGULATOR
	select MFD_CORE
	select REGULATOR_FIXED_VOLTAGE
	help
	  This option enables a driver for the TP61050/TPS61052
	  high-power "white LED driver". This boost converter is
	  sometimes used for other things than white LEDs, and
	  also contains a GPIO pin.

config TPS65010
	tristate "TI TPS6501x Power Management chips"
	depends on I2C && GPIOLIB
	default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK
	help
	  If you say yes here you get support for the TPS6501x series of
	  Power Management chips.  These include voltage regulators,
	  lithium ion/polymer battery charging, and other features that
	  are often used in portable devices like cell phones and cameras.

	  This driver can also be built as a module.  If so, the module
	  will be called tps65010.

config TPS6507X
	tristate "TI TPS6507x Power Management / Touch Screen chips"
	select MFD_CORE
	depends on I2C
	help
	  If you say yes here you get support for the TPS6507x series of
	  Power Management / Touch Screen chips.  These include voltage
	  regulators, lithium ion/polymer battery charging, touch screen
	  and other features that are often used in portable devices.
	  This driver can also be built as a module.  If so, the module
	  will be called tps6507x.

config MFD_TPS65086
	tristate "TI TPS65086 Power Management Integrated Chips (PMICs)"
	select MFD_CORE
	select REGMAP
	select REGMAP_IRQ
	select REGMAP_I2C
	depends on I2C
	help
	  If you say yes here you get support for the TPS65086 series of
	  Power Management chips.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

config TPS65911_COMPARATOR
	tristate

config MFD_TPS65090
	bool "TI TPS65090 Power Management chips"
	depends on I2C=y
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  If you say yes here you get support for the TPS65090 series of
	  Power Management chips.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

config MFD_TPS65217
	tristate "TI TPS65217 Power Management / White LED chips"
	depends on I2C && OF
	select MFD_CORE
	select REGMAP_I2C
	select IRQ_DOMAIN
	help
	  If you say yes here you get support for the TPS65217 series of
	  Power Management / White LED chips.
	  These include voltage regulators, lithium ion/polymer battery
	  charger, wled and other features that are often used in portable
	  devices.

	  This driver can also be built as a module.  If so, the module
	  will be called tps65217.

config MFD_TPS68470
	bool "TI TPS68470 Power Management / LED chips"
	depends on ACPI && I2C=y
	depends on I2C_DESIGNWARE_PLATFORM=y
	select MFD_CORE
	select REGMAP_I2C
	help
	  If you say yes here you get support for the TPS68470 series of
	  Power Management / LED chips.

	  These include voltage regulators, LEDs and other features
	  that are often used in portable devices.

	  This option is a bool as it provides an ACPI operation
	  region, which must be available before any of the devices
	  using this are probed. This option also configures the
	  designware-i2c driver to be built-in, for the same reason.

config MFD_TI_LP873X
	tristate "TI LP873X Power Management IC"
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	help
	  If you say yes here then you get support for the LP873X series of
	  Power Management Integrated Circuits (PMIC).
	  These include voltage regulators, thermal protection, configurable
	  General Purpose Outputs (GPO) that are used in portable devices.

	  This driver can also be built as a module. If so, the module
	  will be called lp873x.

config MFD_TI_LP87565
	tristate "TI LP87565 Power Management IC"
	depends on I2C && OF
	select MFD_CORE
	select REGMAP_I2C
	help
	  If you say yes here then you get support for the LP87565 series of
	  Power Management Integrated Circuits (PMIC).
	  These include voltage regulators, thermal protection, configurable
	  General Purpose Outputs (GPO) that are used in portable devices.

	  This driver can also be built as a module. If so, the module
	  will be called lp87565.

config MFD_TPS65218
	tristate "TI TPS65218 Power Management chips"
	depends on I2C && OF
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  If you say yes here you get support for the TPS65218 series of
	  Power Management chips.
	  These include voltage regulators, gpio and other features
	  that are often used in portable devices.

	  This driver can also be built as a module.  If so, the module
	  will be called tps65218.

config MFD_TPS6586X
	bool "TI TPS6586x Power Management chips"
	depends on I2C=y
	select MFD_CORE
	select REGMAP_I2C
	help
	  If you say yes here you get support for the TPS6586X series of
	  Power Management chips.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

	  This driver can also be built as a module.  If so, the module
	  will be called tps6586x.

config MFD_TPS65910
	bool "TI TPS65910 Power Management chip"
	depends on I2C=y
	depends on GPIOLIB || COMPILE_TEST
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	select IRQ_DOMAIN
	help
	  if you say yes here you get support for the TPS65910 series of
	  Power Management chips.

config MFD_TPS65912
	tristate
	select MFD_CORE
	select REGMAP
	select REGMAP_IRQ

config MFD_TPS65912_I2C
	tristate "TI TPS65912 Power Management chip with I2C"
	select MFD_TPS65912
	select REGMAP_I2C
	depends on I2C
	help
	  If you say yes here you get support for the TPS65912 series of
	  PM chips with I2C interface.

config MFD_TPS65912_SPI
	tristate "TI TPS65912 Power Management chip with SPI"
	select MFD_TPS65912
	select REGMAP_SPI
	depends on SPI_MASTER
	help
	  If you say yes here you get support for the TPS65912 series of
	  PM chips with SPI interface.

config MFD_TPS80031
	bool "TI TPS80031/TPS80032 Power Management chips"
	depends on I2C=y
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	help
	  If you say yes here you get support for the Texas Instruments
	  TPS80031/ TPS80032 Fully Integrated Power Management with Power
	  Path and Battery Charger. The device provides five configurable
	  step-down converters, 11 general purpose LDOs, USB OTG Module,
	  ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with
	  Power Path from USB, 32K clock generator.

config TWL4030_CORE
	bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 Support"
	depends on I2C=y
	select IRQ_DOMAIN
	select REGMAP_I2C
	help
	  Say yes here if you have TWL4030 / TWL6030 family chip on your board.
	  This core driver provides register access and IRQ handling
	  facilities, and registers devices for the various functions
	  so that function-specific drivers can bind to them.

	  These multi-function chips are found on many OMAP2 and OMAP3
	  boards, providing power management, RTC, GPIO, keypad, a
	  high speed USB OTG transceiver, an audio codec (on most
	  versions) and many other features.

config TWL4030_POWER
	bool "TI TWL4030 power resources"
	depends on TWL4030_CORE && ARM
	help
	  Say yes here if you want to use the power resources on the
	  TWL4030 family chips.  Most of these resources are regulators,
	  which have a separate driver; some are control signals, such
	  as clock request handshaking.

	  This driver uses board-specific data to initialize the resources
	  and load scripts controlling which resources are switched off/on
	  or reset when a sleep, wakeup or warm reset event occurs.

config MFD_TWL4030_AUDIO
	bool "TI TWL4030 Audio"
	depends on TWL4030_CORE
	select MFD_CORE
	default n

config TWL6040_CORE
	bool "TI TWL6040 audio codec"
	depends on I2C=y
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	default n
	help
	  Say yes here if you want support for Texas Instruments TWL6040 audio
	  codec.
	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device (audio, vibra).

config MENELAUS
	bool "TI TWL92330/Menelaus PM chip"
	depends on I2C=y && ARCH_OMAP2
	help
	  If you say yes here you get support for the Texas Instruments
	  TWL92330/Menelaus Power Management chip. This include voltage
	  regulators, Dual slot memory card transceivers, real-time clock
	  and other features that are often used in portable devices like
	  cell phones and PDAs.

config MFD_WL1273_CORE
	tristate "TI WL1273 FM radio"
	depends on I2C
	select MFD_CORE
	default n
	help
	  This is the core driver for the TI WL1273 FM radio. This MFD
	  driver connects the radio-wl1273 V4L2 module and the wl1273
	  audio codec.

config MFD_LM3533
	tristate "TI/National Semiconductor LM3533 Lighting Power chip"
	depends on I2C
	select MFD_CORE
	select REGMAP_I2C
	help
	  Say yes here to enable support for National Semiconductor / TI
	  LM3533 Lighting Power chips.

	  This driver provides common support for accessing the device;
	  additional drivers must be enabled in order to use the LED,
	  backlight or ambient-light-sensor functionality of the device.

config MFD_TIMBERDALE
	tristate "Timberdale FPGA"
	select MFD_CORE
	depends on PCI && GPIOLIB && (X86_32 || COMPILE_TEST)
	---help---
	This is the core driver for the timberdale FPGA. This device is a
	multifunction device which exposes numerous platform devices.

	The timberdale FPGA can be found on the Intel Atom development board
	for in-vehicle infontainment, called Russellville.

config MFD_TC3589X
	bool "Toshiba TC35892 and variants"
	depends on I2C=y
	depends on OF
	select MFD_CORE
	help
	  Support for the Toshiba TC35892 and variants I/O Expander.

	  This driver provides common support for accessing the device,
	  additional drivers must be enabled in order to use the
	  functionality of the device.

config MFD_TMIO
	bool
	default n

config MFD_T7L66XB
	bool "Toshiba T7L66XB"
	depends on ARM && HAVE_CLK
	select MFD_CORE
	select MFD_TMIO
	help
	  Support for Toshiba Mobile IO Controller T7L66XB

config MFD_TC6387XB
	bool "Toshiba TC6387XB"
	depends on ARM && HAVE_CLK
	select MFD_CORE
	select MFD_TMIO
	help
	  Support for Toshiba Mobile IO Controller TC6387XB

config MFD_TC6393XB
	bool "Toshiba TC6393XB"
	depends on ARM && HAVE_CLK
	select GPIOLIB
	select MFD_CORE
	select MFD_TMIO
	help
	  Support for Toshiba Mobile IO Controller TC6393XB

config MFD_VX855
	tristate "VIA VX855/VX875 integrated south bridge"
	depends on PCI
	select MFD_CORE
	help
	  Say yes here to enable support for various functions of the
	  VIA VX855/VX875 south bridge. You will need to enable the vx855_spi
	  and/or vx855_gpio drivers for this to do anything useful.

config MFD_LOCHNAGAR
	bool "Cirrus Logic Lochnagar Audio Development Board"
	select MFD_CORE
	select REGMAP_I2C
	depends on I2C=y && OF
	help
	  Support for Cirrus Logic Lochnagar audio development board.

config MFD_ARIZONA
	select REGMAP
	select REGMAP_IRQ
	select MFD_CORE
	bool

config MFD_ARIZONA_I2C
	tristate "Cirrus Logic/Wolfson Microelectronics Arizona platform with I2C"
	select MFD_ARIZONA
	select REGMAP_I2C
	depends on I2C
	help
	  Support for the Cirrus Logic/Wolfson Microelectronics Arizona platform
	  audio SoC core functionality controlled via I2C.

config MFD_ARIZONA_SPI
	tristate "Cirrus Logic/Wolfson Microelectronics Arizona platform with SPI"
	select MFD_ARIZONA
	select REGMAP_SPI
	depends on SPI_MASTER
	help
	  Support for the Cirrus Logic/Wolfson Microelectronics Arizona platform
	  audio SoC core functionality controlled via SPI.

config MFD_CS47L24
	bool "Cirrus Logic CS47L24 and WM1831"
	depends on MFD_ARIZONA
	help
	  Support for Cirrus Logic CS47L24 and WM1831 low power audio SoC

config MFD_WM5102
	bool "Wolfson Microelectronics WM5102"
	depends on MFD_ARIZONA
	help
	  Support for Wolfson Microelectronics WM5102 low power audio SoC

config MFD_WM5110
	bool "Wolfson Microelectronics WM5110 and WM8280/WM8281"
	depends on MFD_ARIZONA
	help
	  Support for Wolfson Microelectronics WM5110 and WM8280/WM8281
	  low power audio SoC

config MFD_WM8997
	bool "Wolfson Microelectronics WM8997"
	depends on MFD_ARIZONA
	help
	  Support for Wolfson Microelectronics WM8997 low power audio SoC

config MFD_WM8998
	bool "Wolfson Microelectronics WM8998"
	depends on MFD_ARIZONA
	help
	  Support for Wolfson Microelectronics WM8998 low power audio SoC

config MFD_WM8400
	bool "Wolfson Microelectronics WM8400"
	select MFD_CORE
	depends on I2C=y
	select REGMAP_I2C
	help
	  Support for the Wolfson Microelecronics WM8400 PMIC and audio
	  CODEC.  This driver provides common support for accessing
	  the device, additional drivers must be enabled in order to use
	  the functionality of the device.

config MFD_WM831X
	bool

config MFD_WM831X_I2C
	bool "Wolfson Microelectronics WM831x/2x PMICs with I2C"
	select MFD_CORE
	select MFD_WM831X
	select REGMAP_I2C
	select IRQ_DOMAIN
	depends on I2C=y
	help
	  Support for the Wolfson Microelecronics WM831x and WM832x PMICs
	  when controlled using I2C.  This driver provides common support
	  for accessing the device, additional drivers must be enabled in
	  order to use the functionality of the device.

config MFD_WM831X_SPI
	bool "Wolfson Microelectronics WM831x/2x PMICs with SPI"
	select MFD_CORE
	select MFD_WM831X
	select REGMAP_SPI
	select IRQ_DOMAIN
	depends on SPI_MASTER
	help
	  Support for the Wolfson Microelecronics WM831x and WM832x PMICs
	  when controlled using SPI.  This driver provides common support
	  for accessing the device, additional drivers must be enabled in
	  order to use the functionality of the device.

config MFD_WM8350
	bool

config MFD_WM8350_I2C
	bool "Wolfson Microelectronics WM8350 with I2C"
	select MFD_WM8350
	select REGMAP_I2C
	depends on I2C=y
	help
	  The WM8350 is an integrated audio and power management
	  subsystem with watchdog and RTC functionality for embedded
	  systems.  This option enables core support for the WM8350 with
	  I2C as the control interface.  Additional options must be
	  selected to enable support for the functionality of the chip.

config MFD_WM8994
	tristate "Wolfson Microelectronics WM8994"
	select MFD_CORE
	select REGMAP_I2C
	select REGMAP_IRQ
	depends on I2C
	help
	  The WM8994 is a highly integrated hi-fi CODEC designed for
	  smartphone applications.  As well as audio functionality it
	  has on board GPIO and regulator functionality which is
	  supported via the relevant subsystems.  This driver provides
	  core support for the WM8994, in order to use the actual
	  functionaltiy of the device other drivers must be enabled.

config MFD_WM97xx
	tristate "Wolfson Microelectronics WM97xx"
	select MFD_CORE
	select REGMAP_AC97
	select AC97_BUS_COMPAT
	depends on AC97_BUS_NEW
	help
	  The WM9705, WM9712 and WM9713 is a highly integrated hi-fi CODEC
	  designed for smartphone applications.  As well as audio functionality
	  it has on board GPIO and a touchscreen functionality which is
	  supported via the relevant subsystems.  This driver provides core
	  support for the WM97xx, in order to use the actual functionaltiy of
	  the device other drivers must be enabled.

config MFD_STW481X
	tristate "Support for ST Microelectronics STw481x"
	depends on I2C && (ARCH_NOMADIK || COMPILE_TEST)
	select REGMAP_I2C
	select MFD_CORE
	help
	  Select this option to enable the STw481x chip driver used
	  in various ST Microelectronics and ST-Ericsson embedded
	  Nomadik series.

config MFD_ROHM_BD718XX
	tristate "ROHM BD71837 Power Management IC"
	depends on I2C=y
	depends on OF
	select REGMAP_I2C
	select REGMAP_IRQ
	select MFD_CORE
	help
	  Select this option to get support for the ROHM BD71837
	  Power Management ICs. BD71837 is designed to power processors like
	  NXP i.MX8. It contains 8 BUCK outputs and 7 LDOs, voltage monitoring
	  and emergency shut down as well as 32,768KHz clock output.

config MFD_STM32_LPTIMER
	tristate "Support for STM32 Low-Power Timer"
	depends on (ARCH_STM32 && OF) || COMPILE_TEST
	select MFD_CORE
	select REGMAP
	select REGMAP_MMIO
	help
	  Select this option to enable STM32 Low-Power Timer driver
	  used for PWM, IIO Trigger, IIO Encoder and Counter. Shared
	  resources are also dealt with here.

	  To compile this driver as a module, choose M here: the
	  module will be called stm32-lptimer.

config MFD_STM32_TIMERS
	tristate "Support for STM32 Timers"
	depends on (ARCH_STM32 && OF) || COMPILE_TEST
	select MFD_CORE
	select REGMAP
	select REGMAP_MMIO
	help
	  Select this option to enable STM32 timers driver used
	  for PWM and IIO Timer. This driver allow to share the
	  registers between the others drivers.

config MFD_STPMIC1
	tristate "Support for STPMIC1 PMIC"
	depends on (I2C=y && OF)
	select REGMAP_I2C
	select REGMAP_IRQ
	select MFD_CORE
	help
	  Support for ST Microelectronics STPMIC1 PMIC. STPMIC1 has power on
	  key, watchdog and regulator functionalities which are supported via
	  the relevant subsystems. This driver provides core support for the
	  STPMIC1. In order to use the actual functionaltiy of the device other
	  drivers must be enabled.

	  To compile this driver as a module, choose M here: the
	  module will be called stpmic1.

menu "Multimedia Capabilities Port drivers"
	depends on ARCH_SA1100

config MCP
	tristate

# Interface drivers
config MCP_SA11X0
	tristate "Support SA11x0 MCP interface"
	depends on ARCH_SA1100
	select MCP

# Chip drivers
config MCP_UCB1200
	tristate "Support for UCB1200 / UCB1300"
	depends on MCP_SA11X0
	select MCP

config MCP_UCB1200_TS
	tristate "Touchscreen interface support"
	depends on MCP_UCB1200 && INPUT

endmenu

config MFD_VEXPRESS_SYSREG
	bool "Versatile Express System Registers"
	depends on VEXPRESS_CONFIG && GPIOLIB && !ARCH_USES_GETTIMEOFFSET
	default y
	select CLKSRC_MMIO
	select GPIO_GENERIC_PLATFORM
	select MFD_CORE
	select MFD_SYSCON
	help
	  System Registers are the platform configuration block
	  on the ARM Ltd. Versatile Express board.

config RAVE_SP_CORE
	tristate "RAVE SP MCU core driver"
	depends on SERIAL_DEV_BUS
	select CRC_CCITT
	help
	  Select this to get support for the Supervisory Processor
	  device found on several devices in RAVE line of hardware.

endmenu
endif