Merge branches 'ib-mfd-gpio-4.12', 'ib-mfd-iio-input-4.12', 'ib-mfd-input-4.12', 'ib-mfd-leds-4.12', 'ib-mfd-phy-4.12' and 'ib-mfd-pinctrl-samsung-4.12' into ibs-for-mfd-merged
diff --git a/Documentation/devicetree/bindings/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/mfd/mxs-lradc.txt
similarity index 100%
rename from Documentation/devicetree/bindings/iio/adc/mxs-lradc.txt
rename to Documentation/devicetree/bindings/mfd/mxs-lradc.txt
diff --git a/Documentation/devicetree/bindings/mfd/wm831x.txt b/Documentation/devicetree/bindings/mfd/wm831x.txt
new file mode 100644
index 0000000..9f8b743
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/wm831x.txt
@@ -0,0 +1,81 @@
+Cirrus Logic/Wolfson Microelectronics wm831x PMICs
+
+System PMICs with a wide range of additional features.
+
+Required properties:
+
+ - compatible : One of the following chip-specific strings:
+ "wlf,wm8310"
+ "wlf,wm8311"
+ "wlf,wm8312"
+ "wlf,wm8320"
+ "wlf,wm8321"
+ "wlf,wm8325"
+ "wlf,wm8326"
+
+ - reg : I2C slave address when connected using I2C, chip select number
+ when using SPI.
+
+ - gpio-controller : Indicates this device is a GPIO controller.
+ - #gpio-cells : Must be 2. The first cell is the pin number and the
+ second cell is used to specify optional parameters (currently unused).
+
+ - interrupts : The interrupt line the IRQ signal for the device is
+ connected to.
+ - interrupt-parent : The parent interrupt controller.
+
+ - interrupt-controller : wm831x devices contain interrupt controllers and
+ may provide interrupt services to other devices.
+ - #interrupt-cells: Must be 2. The first cell is the IRQ number, and the
+ second cell is the flags, encoded as the trigger masks from
+ ../interrupt-controller/interrupts.txt
+
+Optional sub-nodes:
+ - regulators : Contains sub-nodes for each of the regulators supplied by
+ the device. The regulators are bound using their names listed below:
+
+ dcdc1 : DCDC1
+ dcdc2 : DCDC2
+ dcdc3 : DCDC3
+ dcdc4 : DCDC3
+ isink1 : ISINK1
+ isink2 : ISINK2
+ ldo1 : LDO1
+ ldo2 : LDO2
+ ldo3 : LDO3
+ ldo4 : LDO4
+ ldo5 : LDO5
+ ldo7 : LDO7
+ ldo11 : LDO11
+
+ The bindings details of each regulator can be found in:
+ ../regulator/regulator.txt
+
+Example:
+
+wm8310: pmic@36 {
+ compatible = "wlf,wm8310";
+ reg = <0x36>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupts = <347>;
+ interrupt-parent = <&gic>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ regulators {
+ dcdc1: dcdc1 {
+ regulator-name = "DCDC1";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <600000>;
+ };
+ ldo1: ldo1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1700000>;
+ };
+ };
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index c265a5f..dfe761b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13600,6 +13600,7 @@
F: Documentation/devicetree/bindings/extcon/extcon-arizona.txt
F: Documentation/devicetree/bindings/regulator/arizona-regulator.txt
F: Documentation/devicetree/bindings/mfd/arizona.txt
+F: Documentation/devicetree/bindings/mfd/wm831x.txt
F: arch/arm/mach-s3c64xx/mach-crag6410*
F: drivers/clk/clk-wm83*.c
F: drivers/extcon/extcon-arizona.c
diff --git a/drivers/gpio/gpio-wm831x.c b/drivers/gpio/gpio-wm831x.c
index 00e3839..938bbe3 100644
--- a/drivers/gpio/gpio-wm831x.c
+++ b/drivers/gpio/gpio-wm831x.c
@@ -263,7 +263,7 @@ static const struct gpio_chip template_chip = {
static int wm831x_gpio_probe(struct platform_device *pdev)
{
struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent);
- struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev);
+ struct wm831x_pdata *pdata = &wm831x->pdata;
struct wm831x_gpio *wm831x_gpio;
int ret;
@@ -280,6 +280,9 @@ static int wm831x_gpio_probe(struct platform_device *pdev)
wm831x_gpio->gpio_chip.base = pdata->gpio_base;
else
wm831x_gpio->gpio_chip.base = -1;
+#ifdef CONFIG_OF_GPIO
+ wm831x_gpio->gpio_chip.of_node = wm831x->dev->of_node;
+#endif
ret = devm_gpiochip_add_data(&pdev->dev, &wm831x_gpio->gpio_chip,
wm831x_gpio);
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index dedae7a..5d13405 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -229,6 +229,19 @@
To compile this driver as a module, choose M here: the module will be
called exynos_adc.
+config MXS_LRADC_ADC
+ tristate "Freescale i.MX23/i.MX28 LRADC ADC"
+ depends on MFD_MXS_LRADC
+ select IIO_BUFFER
+ select IIO_TRIGGERED_BUFFER
+ help
+ Say yes here to build support for the ADC functions of the
+ i.MX23/i.MX28 LRADC. This includes general-purpose ADC readings,
+ battery voltage measurement, and die temperature measurement.
+
+ This driver can also be built as a module. If so, the module will be
+ called mxs-lradc-adc.
+
config FSL_MX25_ADC
tristate "Freescale MX25 ADC driver"
depends on MFD_MX25_TSADC
@@ -411,20 +424,6 @@
To compile this driver as a module, choose M here: the
module will be called meson_saradc.
-config MXS_LRADC
- tristate "Freescale i.MX23/i.MX28 LRADC"
- depends on (ARCH_MXS || COMPILE_TEST) && HAS_IOMEM
- depends on INPUT
- select STMP_DEVICE
- select IIO_BUFFER
- select IIO_TRIGGERED_BUFFER
- help
- Say yes here to build support for i.MX23/i.MX28 LRADC convertor
- built into these chips.
-
- To compile this driver as a module, choose M here: the
- module will be called mxs-lradc.
-
config NAU7802
tristate "Nuvoton NAU7802 ADC driver"
depends on I2C
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index d001262..54b5f72 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -39,7 +39,7 @@
obj-$(CONFIG_MEDIATEK_MT6577_AUXADC) += mt6577_auxadc.o
obj-$(CONFIG_MEN_Z188_ADC) += men_z188_adc.o
obj-$(CONFIG_MESON_SARADC) += meson_saradc.o
-obj-$(CONFIG_MXS_LRADC) += mxs-lradc.o
+obj-$(CONFIG_MXS_LRADC_ADC) += mxs-lradc-adc.o
obj-$(CONFIG_NAU7802) += nau7802.o
obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
diff --git a/drivers/iio/adc/mxs-lradc-adc.c b/drivers/iio/adc/mxs-lradc-adc.c
new file mode 100644
index 0000000..b0c7d8e
--- /dev/null
+++ b/drivers/iio/adc/mxs-lradc-adc.c
@@ -0,0 +1,843 @@
+/*
+ * Freescale MXS LRADC ADC driver
+ *
+ * Copyright (c) 2012 DENX Software Engineering, GmbH.
+ * Copyright (c) 2017 Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
+ *
+ * Authors:
+ * Marek Vasut <marex@denx.de>
+ * Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/mxs-lradc.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/sysfs.h>
+
+#include <linux/iio/buffer.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/sysfs.h>
+
+/*
+ * Make this runtime configurable if necessary. Currently, if the buffered mode
+ * is enabled, the LRADC takes LRADC_DELAY_TIMER_LOOP samples of data before
+ * triggering IRQ. The sampling happens every (LRADC_DELAY_TIMER_PER / 2000)
+ * seconds. The result is that the samples arrive every 500mS.
+ */
+#define LRADC_DELAY_TIMER_PER 200
+#define LRADC_DELAY_TIMER_LOOP 5
+
+#define VREF_MV_BASE 1850
+
+const char *mx23_lradc_adc_irq_names[] = {
+ "mxs-lradc-channel0",
+ "mxs-lradc-channel1",
+ "mxs-lradc-channel2",
+ "mxs-lradc-channel3",
+ "mxs-lradc-channel4",
+ "mxs-lradc-channel5",
+};
+
+const char *mx28_lradc_adc_irq_names[] = {
+ "mxs-lradc-thresh0",
+ "mxs-lradc-thresh1",
+ "mxs-lradc-channel0",
+ "mxs-lradc-channel1",
+ "mxs-lradc-channel2",
+ "mxs-lradc-channel3",
+ "mxs-lradc-channel4",
+ "mxs-lradc-channel5",
+ "mxs-lradc-button0",
+ "mxs-lradc-button1",
+};
+
+static const u32 mxs_lradc_adc_vref_mv[][LRADC_MAX_TOTAL_CHANS] = {
+ [IMX23_LRADC] = {
+ VREF_MV_BASE, /* CH0 */
+ VREF_MV_BASE, /* CH1 */
+ VREF_MV_BASE, /* CH2 */
+ VREF_MV_BASE, /* CH3 */
+ VREF_MV_BASE, /* CH4 */
+ VREF_MV_BASE, /* CH5 */
+ VREF_MV_BASE * 2, /* CH6 VDDIO */
+ VREF_MV_BASE * 4, /* CH7 VBATT */
+ VREF_MV_BASE, /* CH8 Temp sense 0 */
+ VREF_MV_BASE, /* CH9 Temp sense 1 */
+ VREF_MV_BASE, /* CH10 */
+ VREF_MV_BASE, /* CH11 */
+ VREF_MV_BASE, /* CH12 USB_DP */
+ VREF_MV_BASE, /* CH13 USB_DN */
+ VREF_MV_BASE, /* CH14 VBG */
+ VREF_MV_BASE * 4, /* CH15 VDD5V */
+ },
+ [IMX28_LRADC] = {
+ VREF_MV_BASE, /* CH0 */
+ VREF_MV_BASE, /* CH1 */
+ VREF_MV_BASE, /* CH2 */
+ VREF_MV_BASE, /* CH3 */
+ VREF_MV_BASE, /* CH4 */
+ VREF_MV_BASE, /* CH5 */
+ VREF_MV_BASE, /* CH6 */
+ VREF_MV_BASE * 4, /* CH7 VBATT */
+ VREF_MV_BASE, /* CH8 Temp sense 0 */
+ VREF_MV_BASE, /* CH9 Temp sense 1 */
+ VREF_MV_BASE * 2, /* CH10 VDDIO */
+ VREF_MV_BASE, /* CH11 VTH */
+ VREF_MV_BASE * 2, /* CH12 VDDA */
+ VREF_MV_BASE, /* CH13 VDDD */
+ VREF_MV_BASE, /* CH14 VBG */
+ VREF_MV_BASE * 4, /* CH15 VDD5V */
+ },
+};
+
+enum mxs_lradc_divbytwo {
+ MXS_LRADC_DIV_DISABLED = 0,
+ MXS_LRADC_DIV_ENABLED,
+};
+
+struct mxs_lradc_scale {
+ unsigned int integer;
+ unsigned int nano;
+};
+
+struct mxs_lradc_adc {
+ struct mxs_lradc *lradc;
+ struct device *dev;
+
+ void __iomem *base;
+ u32 buffer[10];
+ struct iio_trigger *trig;
+ struct completion completion;
+ spinlock_t lock;
+
+ const u32 *vref_mv;
+ struct mxs_lradc_scale scale_avail[LRADC_MAX_TOTAL_CHANS][2];
+ unsigned long is_divided;
+};
+
+
+/* Raw I/O operations */
+static int mxs_lradc_adc_read_single(struct iio_dev *iio_dev, int chan,
+ int *val)
+{
+ struct mxs_lradc_adc *adc = iio_priv(iio_dev);
+ struct mxs_lradc *lradc = adc->lradc;
+ int ret;
+
+ /*
+ * See if there is no buffered operation in progress. If there is simply
+ * bail out. This can be improved to support both buffered and raw IO at
+ * the same time, yet the code becomes horribly complicated. Therefore I
+ * applied KISS principle here.
+ */
+ ret = iio_device_claim_direct_mode(iio_dev);
+ if (ret)
+ return ret;
+
+ reinit_completion(&adc->completion);
+
+ /*
+ * No buffered operation in progress, map the channel and trigger it.
+ * Virtual channel 0 is always used here as the others are always not
+ * used if doing raw sampling.
+ */
+ if (lradc->soc == IMX28_LRADC)
+ writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
+ adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+ writel(0x1, adc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+
+ /* Enable / disable the divider per requirement */
+ if (test_bit(chan, &adc->is_divided))
+ writel(1 << LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET,
+ adc->base + LRADC_CTRL2 + STMP_OFFSET_REG_SET);
+ else
+ writel(1 << LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET,
+ adc->base + LRADC_CTRL2 + STMP_OFFSET_REG_CLR);
+
+ /* Clean the slot's previous content, then set new one. */
+ writel(LRADC_CTRL4_LRADCSELECT_MASK(0),
+ adc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
+ writel(chan, adc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+
+ writel(0, adc->base + LRADC_CH(0));
+
+ /* Enable the IRQ and start sampling the channel. */
+ writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
+ adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+ writel(BIT(0), adc->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+
+ /* Wait for completion on the channel, 1 second max. */
+ ret = wait_for_completion_killable_timeout(&adc->completion, HZ);
+ if (!ret)
+ ret = -ETIMEDOUT;
+ if (ret < 0)
+ goto err;
+
+ /* Read the data. */
+ *val = readl(adc->base + LRADC_CH(0)) & LRADC_CH_VALUE_MASK;
+ ret = IIO_VAL_INT;
+
+err:
+ writel(LRADC_CTRL1_LRADC_IRQ_EN(0),
+ adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+
+ iio_device_release_direct_mode(iio_dev);
+
+ return ret;
+}
+
+static int mxs_lradc_adc_read_temp(struct iio_dev *iio_dev, int *val)
+{
+ int ret, min, max;
+
+ ret = mxs_lradc_adc_read_single(iio_dev, 8, &min);
+ if (ret != IIO_VAL_INT)
+ return ret;
+
+ ret = mxs_lradc_adc_read_single(iio_dev, 9, &max);
+ if (ret != IIO_VAL_INT)
+ return ret;
+
+ *val = max - min;
+
+ return IIO_VAL_INT;
+}
+
+static int mxs_lradc_adc_read_raw(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
+ int *val, int *val2, long m)
+{
+ struct mxs_lradc_adc *adc = iio_priv(iio_dev);
+
+ switch (m) {
+ case IIO_CHAN_INFO_RAW:
+ if (chan->type == IIO_TEMP)
+ return mxs_lradc_adc_read_temp(iio_dev, val);
+
+ return mxs_lradc_adc_read_single(iio_dev, chan->channel, val);
+
+ case IIO_CHAN_INFO_SCALE:
+ if (chan->type == IIO_TEMP) {
+ /*
+ * From the datasheet, we have to multiply by 1.012 and
+ * divide by 4
+ */
+ *val = 0;
+ *val2 = 253000;
+ return IIO_VAL_INT_PLUS_MICRO;
+ }
+
+ *val = adc->vref_mv[chan->channel];
+ *val2 = chan->scan_type.realbits -
+ test_bit(chan->channel, &adc->is_divided);
+ return IIO_VAL_FRACTIONAL_LOG2;
+
+ case IIO_CHAN_INFO_OFFSET:
+ if (chan->type == IIO_TEMP) {
+ /*
+ * The calculated value from the ADC is in Kelvin, we
+ * want Celsius for hwmon so the offset is -273.15
+ * The offset is applied before scaling so it is
+ * actually -213.15 * 4 / 1.012 = -1079.644268
+ */
+ *val = -1079;
+ *val2 = 644268;
+
+ return IIO_VAL_INT_PLUS_MICRO;
+ }
+
+ return -EINVAL;
+
+ default:
+ break;
+ }
+
+ return -EINVAL;
+}
+
+static int mxs_lradc_adc_write_raw(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
+ int val, int val2, long m)
+{
+ struct mxs_lradc_adc *adc = iio_priv(iio_dev);
+ struct mxs_lradc_scale *scale_avail =
+ adc->scale_avail[chan->channel];
+ int ret;
+
+ ret = iio_device_claim_direct_mode(iio_dev);
+ if (ret)
+ return ret;
+
+ switch (m) {
+ case IIO_CHAN_INFO_SCALE:
+ ret = -EINVAL;
+ if (val == scale_avail[MXS_LRADC_DIV_DISABLED].integer &&
+ val2 == scale_avail[MXS_LRADC_DIV_DISABLED].nano) {
+ /* divider by two disabled */
+ clear_bit(chan->channel, &adc->is_divided);
+ ret = 0;
+ } else if (val == scale_avail[MXS_LRADC_DIV_ENABLED].integer &&
+ val2 == scale_avail[MXS_LRADC_DIV_ENABLED].nano) {
+ /* divider by two enabled */
+ set_bit(chan->channel, &adc->is_divided);
+ ret = 0;
+ }
+
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ iio_device_release_direct_mode(iio_dev);
+
+ return ret;
+}
+
+static int mxs_lradc_adc_write_raw_get_fmt(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
+ long m)
+{
+ return IIO_VAL_INT_PLUS_NANO;
+}
+
+static ssize_t mxs_lradc_adc_show_scale_avail(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct iio_dev *iio = dev_to_iio_dev(dev);
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+ struct iio_dev_attr *iio_attr = to_iio_dev_attr(attr);
+ int i, ch, len = 0;
+
+ ch = iio_attr->address;
+ for (i = 0; i < ARRAY_SIZE(adc->scale_avail[ch]); i++)
+ len += sprintf(buf + len, "%u.%09u ",
+ adc->scale_avail[ch][i].integer,
+ adc->scale_avail[ch][i].nano);
+
+ len += sprintf(buf + len, "\n");
+
+ return len;
+}
+
+#define SHOW_SCALE_AVAILABLE_ATTR(ch)\
+ IIO_DEVICE_ATTR(in_voltage##ch##_scale_available, 0444,\
+ mxs_lradc_adc_show_scale_avail, NULL, ch)
+
+SHOW_SCALE_AVAILABLE_ATTR(0);
+SHOW_SCALE_AVAILABLE_ATTR(1);
+SHOW_SCALE_AVAILABLE_ATTR(2);
+SHOW_SCALE_AVAILABLE_ATTR(3);
+SHOW_SCALE_AVAILABLE_ATTR(4);
+SHOW_SCALE_AVAILABLE_ATTR(5);
+SHOW_SCALE_AVAILABLE_ATTR(6);
+SHOW_SCALE_AVAILABLE_ATTR(7);
+SHOW_SCALE_AVAILABLE_ATTR(10);
+SHOW_SCALE_AVAILABLE_ATTR(11);
+SHOW_SCALE_AVAILABLE_ATTR(12);
+SHOW_SCALE_AVAILABLE_ATTR(13);
+SHOW_SCALE_AVAILABLE_ATTR(14);
+SHOW_SCALE_AVAILABLE_ATTR(15);
+
+static struct attribute *mxs_lradc_adc_attributes[] = {
+ &iio_dev_attr_in_voltage0_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage1_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage2_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage3_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage4_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage5_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage6_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage7_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage10_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage11_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage12_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage13_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage14_scale_available.dev_attr.attr,
+ &iio_dev_attr_in_voltage15_scale_available.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group mxs_lradc_adc_attribute_group = {
+ .attrs = mxs_lradc_adc_attributes,
+};
+
+static const struct iio_info mxs_lradc_adc_iio_info = {
+ .driver_module = THIS_MODULE,
+ .read_raw = mxs_lradc_adc_read_raw,
+ .write_raw = mxs_lradc_adc_write_raw,
+ .write_raw_get_fmt = mxs_lradc_adc_write_raw_get_fmt,
+ .attrs = &mxs_lradc_adc_attribute_group,
+};
+
+/* IRQ Handling */
+static irqreturn_t mxs_lradc_adc_handle_irq(int irq, void *data)
+{
+ struct iio_dev *iio = data;
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+ struct mxs_lradc *lradc = adc->lradc;
+ unsigned long reg = readl(adc->base + LRADC_CTRL1);
+ unsigned long flags;
+
+ if (!(reg & mxs_lradc_irq_mask(lradc)))
+ return IRQ_NONE;
+
+ if (iio_buffer_enabled(iio)) {
+ if (reg & lradc->buffer_vchans) {
+ spin_lock_irqsave(&adc->lock, flags);
+ iio_trigger_poll(iio->trig);
+ spin_unlock_irqrestore(&adc->lock, flags);
+ }
+ } else if (reg & LRADC_CTRL1_LRADC_IRQ(0)) {
+ complete(&adc->completion);
+ }
+
+ writel(reg & mxs_lradc_irq_mask(lradc),
+ adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+
+ return IRQ_HANDLED;
+}
+
+
+/* Trigger handling */
+static irqreturn_t mxs_lradc_adc_trigger_handler(int irq, void *p)
+{
+ struct iio_poll_func *pf = p;
+ struct iio_dev *iio = pf->indio_dev;
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+ const u32 chan_value = LRADC_CH_ACCUMULATE |
+ ((LRADC_DELAY_TIMER_LOOP - 1) << LRADC_CH_NUM_SAMPLES_OFFSET);
+ unsigned int i, j = 0;
+
+ for_each_set_bit(i, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
+ adc->buffer[j] = readl(adc->base + LRADC_CH(j));
+ writel(chan_value, adc->base + LRADC_CH(j));
+ adc->buffer[j] &= LRADC_CH_VALUE_MASK;
+ adc->buffer[j] /= LRADC_DELAY_TIMER_LOOP;
+ j++;
+ }
+
+ iio_push_to_buffers_with_timestamp(iio, adc->buffer, pf->timestamp);
+
+ iio_trigger_notify_done(iio->trig);
+
+ return IRQ_HANDLED;
+}
+
+static int mxs_lradc_adc_configure_trigger(struct iio_trigger *trig, bool state)
+{
+ struct iio_dev *iio = iio_trigger_get_drvdata(trig);
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+ const u32 st = state ? STMP_OFFSET_REG_SET : STMP_OFFSET_REG_CLR;
+
+ writel(LRADC_DELAY_KICK, adc->base + (LRADC_DELAY(0) + st));
+
+ return 0;
+}
+
+static const struct iio_trigger_ops mxs_lradc_adc_trigger_ops = {
+ .owner = THIS_MODULE,
+ .set_trigger_state = &mxs_lradc_adc_configure_trigger,
+};
+
+static int mxs_lradc_adc_trigger_init(struct iio_dev *iio)
+{
+ int ret;
+ struct iio_trigger *trig;
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+
+ trig = devm_iio_trigger_alloc(&iio->dev, "%s-dev%i", iio->name,
+ iio->id);
+
+ trig->dev.parent = adc->dev;
+ iio_trigger_set_drvdata(trig, iio);
+ trig->ops = &mxs_lradc_adc_trigger_ops;
+
+ ret = iio_trigger_register(trig);
+ if (ret)
+ return ret;
+
+ adc->trig = trig;
+
+ return 0;
+}
+
+static void mxs_lradc_adc_trigger_remove(struct iio_dev *iio)
+{
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+
+ iio_trigger_unregister(adc->trig);
+}
+
+static int mxs_lradc_adc_buffer_preenable(struct iio_dev *iio)
+{
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+ struct mxs_lradc *lradc = adc->lradc;
+ int chan, ofs = 0;
+ unsigned long enable = 0;
+ u32 ctrl4_set = 0;
+ u32 ctrl4_clr = 0;
+ u32 ctrl1_irq = 0;
+ const u32 chan_value = LRADC_CH_ACCUMULATE |
+ ((LRADC_DELAY_TIMER_LOOP - 1) << LRADC_CH_NUM_SAMPLES_OFFSET);
+
+ if (lradc->soc == IMX28_LRADC)
+ writel(lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
+ adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+ writel(lradc->buffer_vchans,
+ adc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+
+ for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
+ ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs);
+ ctrl4_clr |= LRADC_CTRL4_LRADCSELECT_MASK(ofs);
+ ctrl1_irq |= LRADC_CTRL1_LRADC_IRQ_EN(ofs);
+ writel(chan_value, adc->base + LRADC_CH(ofs));
+ bitmap_set(&enable, ofs, 1);
+ ofs++;
+ }
+
+ writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
+ adc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
+ writel(ctrl4_clr, adc->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
+ writel(ctrl4_set, adc->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+ writel(ctrl1_irq, adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+ writel(enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
+ adc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_SET);
+
+ return 0;
+}
+
+static int mxs_lradc_adc_buffer_postdisable(struct iio_dev *iio)
+{
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+ struct mxs_lradc *lradc = adc->lradc;
+
+ writel(LRADC_DELAY_TRIGGER_LRADCS_MASK | LRADC_DELAY_KICK,
+ adc->base + LRADC_DELAY(0) + STMP_OFFSET_REG_CLR);
+
+ writel(lradc->buffer_vchans,
+ adc->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+ if (lradc->soc == IMX28_LRADC)
+ writel(lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
+ adc->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+
+ return 0;
+}
+
+static bool mxs_lradc_adc_validate_scan_mask(struct iio_dev *iio,
+ const unsigned long *mask)
+{
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+ struct mxs_lradc *lradc = adc->lradc;
+ const int map_chans = bitmap_weight(mask, LRADC_MAX_TOTAL_CHANS);
+ int rsvd_chans = 0;
+ unsigned long rsvd_mask = 0;
+
+ if (lradc->use_touchbutton)
+ rsvd_mask |= CHAN_MASK_TOUCHBUTTON;
+ if (lradc->touchscreen_wire == MXS_LRADC_TOUCHSCREEN_4WIRE)
+ rsvd_mask |= CHAN_MASK_TOUCHSCREEN_4WIRE;
+ if (lradc->touchscreen_wire == MXS_LRADC_TOUCHSCREEN_5WIRE)
+ rsvd_mask |= CHAN_MASK_TOUCHSCREEN_5WIRE;
+
+ if (lradc->use_touchbutton)
+ rsvd_chans++;
+ if (lradc->touchscreen_wire)
+ rsvd_chans += 2;
+
+ /* Test for attempts to map channels with special mode of operation. */
+ if (bitmap_intersects(mask, &rsvd_mask, LRADC_MAX_TOTAL_CHANS))
+ return false;
+
+ /* Test for attempts to map more channels then available slots. */
+ if (map_chans + rsvd_chans > LRADC_MAX_MAPPED_CHANS)
+ return false;
+
+ return true;
+}
+
+static const struct iio_buffer_setup_ops mxs_lradc_adc_buffer_ops = {
+ .preenable = &mxs_lradc_adc_buffer_preenable,
+ .postenable = &iio_triggered_buffer_postenable,
+ .predisable = &iio_triggered_buffer_predisable,
+ .postdisable = &mxs_lradc_adc_buffer_postdisable,
+ .validate_scan_mask = &mxs_lradc_adc_validate_scan_mask,
+};
+
+/* Driver initialization */
+#define MXS_ADC_CHAN(idx, chan_type, name) { \
+ .type = (chan_type), \
+ .indexed = 1, \
+ .scan_index = (idx), \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+ BIT(IIO_CHAN_INFO_SCALE), \
+ .channel = (idx), \
+ .address = (idx), \
+ .scan_type = { \
+ .sign = 'u', \
+ .realbits = LRADC_RESOLUTION, \
+ .storagebits = 32, \
+ }, \
+ .datasheet_name = (name), \
+}
+
+static const struct iio_chan_spec mx23_lradc_chan_spec[] = {
+ MXS_ADC_CHAN(0, IIO_VOLTAGE, "LRADC0"),
+ MXS_ADC_CHAN(1, IIO_VOLTAGE, "LRADC1"),
+ MXS_ADC_CHAN(2, IIO_VOLTAGE, "LRADC2"),
+ MXS_ADC_CHAN(3, IIO_VOLTAGE, "LRADC3"),
+ MXS_ADC_CHAN(4, IIO_VOLTAGE, "LRADC4"),
+ MXS_ADC_CHAN(5, IIO_VOLTAGE, "LRADC5"),
+ MXS_ADC_CHAN(6, IIO_VOLTAGE, "VDDIO"),
+ MXS_ADC_CHAN(7, IIO_VOLTAGE, "VBATT"),
+ /* Combined Temperature sensors */
+ {
+ .type = IIO_TEMP,
+ .indexed = 1,
+ .scan_index = 8,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_OFFSET) |
+ BIT(IIO_CHAN_INFO_SCALE),
+ .channel = 8,
+ .scan_type = {.sign = 'u', .realbits = 18, .storagebits = 32,},
+ .datasheet_name = "TEMP_DIE",
+ },
+ /* Hidden channel to keep indexes */
+ {
+ .type = IIO_TEMP,
+ .indexed = 1,
+ .scan_index = -1,
+ .channel = 9,
+ },
+ MXS_ADC_CHAN(10, IIO_VOLTAGE, NULL),
+ MXS_ADC_CHAN(11, IIO_VOLTAGE, NULL),
+ MXS_ADC_CHAN(12, IIO_VOLTAGE, "USB_DP"),
+ MXS_ADC_CHAN(13, IIO_VOLTAGE, "USB_DN"),
+ MXS_ADC_CHAN(14, IIO_VOLTAGE, "VBG"),
+ MXS_ADC_CHAN(15, IIO_VOLTAGE, "VDD5V"),
+};
+
+static const struct iio_chan_spec mx28_lradc_chan_spec[] = {
+ MXS_ADC_CHAN(0, IIO_VOLTAGE, "LRADC0"),
+ MXS_ADC_CHAN(1, IIO_VOLTAGE, "LRADC1"),
+ MXS_ADC_CHAN(2, IIO_VOLTAGE, "LRADC2"),
+ MXS_ADC_CHAN(3, IIO_VOLTAGE, "LRADC3"),
+ MXS_ADC_CHAN(4, IIO_VOLTAGE, "LRADC4"),
+ MXS_ADC_CHAN(5, IIO_VOLTAGE, "LRADC5"),
+ MXS_ADC_CHAN(6, IIO_VOLTAGE, "LRADC6"),
+ MXS_ADC_CHAN(7, IIO_VOLTAGE, "VBATT"),
+ /* Combined Temperature sensors */
+ {
+ .type = IIO_TEMP,
+ .indexed = 1,
+ .scan_index = 8,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_OFFSET) |
+ BIT(IIO_CHAN_INFO_SCALE),
+ .channel = 8,
+ .scan_type = {.sign = 'u', .realbits = 18, .storagebits = 32,},
+ .datasheet_name = "TEMP_DIE",
+ },
+ /* Hidden channel to keep indexes */
+ {
+ .type = IIO_TEMP,
+ .indexed = 1,
+ .scan_index = -1,
+ .channel = 9,
+ },
+ MXS_ADC_CHAN(10, IIO_VOLTAGE, "VDDIO"),
+ MXS_ADC_CHAN(11, IIO_VOLTAGE, "VTH"),
+ MXS_ADC_CHAN(12, IIO_VOLTAGE, "VDDA"),
+ MXS_ADC_CHAN(13, IIO_VOLTAGE, "VDDD"),
+ MXS_ADC_CHAN(14, IIO_VOLTAGE, "VBG"),
+ MXS_ADC_CHAN(15, IIO_VOLTAGE, "VDD5V"),
+};
+
+static void mxs_lradc_adc_hw_init(struct mxs_lradc_adc *adc)
+{
+ /* The ADC always uses DELAY CHANNEL 0. */
+ const u32 adc_cfg =
+ (1 << (LRADC_DELAY_TRIGGER_DELAYS_OFFSET + 0)) |
+ (LRADC_DELAY_TIMER_PER << LRADC_DELAY_DELAY_OFFSET);
+
+ /* Configure DELAY CHANNEL 0 for generic ADC sampling. */
+ writel(adc_cfg, adc->base + LRADC_DELAY(0));
+
+ /*
+ * Start internal temperature sensing by clearing bit
+ * HW_LRADC_CTRL2_TEMPSENSE_PWD. This bit can be left cleared
+ * after power up.
+ */
+ writel(0, adc->base + LRADC_CTRL2);
+}
+
+static void mxs_lradc_adc_hw_stop(struct mxs_lradc_adc *adc)
+{
+ writel(0, adc->base + LRADC_DELAY(0));
+}
+
+static int mxs_lradc_adc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct mxs_lradc *lradc = dev_get_drvdata(dev->parent);
+ struct mxs_lradc_adc *adc;
+ struct iio_dev *iio;
+ struct resource *iores;
+ int ret, irq, virq, i, s, n;
+ u64 scale_uv;
+ const char **irq_name;
+
+ /* Allocate the IIO device. */
+ iio = devm_iio_device_alloc(dev, sizeof(*adc));
+ if (!iio) {
+ dev_err(dev, "Failed to allocate IIO device\n");
+ return -ENOMEM;
+ }
+
+ adc = iio_priv(iio);
+ adc->lradc = lradc;
+ adc->dev = dev;
+
+ iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ adc->base = devm_ioremap(dev, iores->start, resource_size(iores));
+ if (IS_ERR(adc->base))
+ return PTR_ERR(adc->base);
+
+ init_completion(&adc->completion);
+ spin_lock_init(&adc->lock);
+
+ platform_set_drvdata(pdev, iio);
+
+ iio->name = pdev->name;
+ iio->dev.parent = dev;
+ iio->dev.of_node = dev->parent->of_node;
+ iio->info = &mxs_lradc_adc_iio_info;
+ iio->modes = INDIO_DIRECT_MODE;
+ iio->masklength = LRADC_MAX_TOTAL_CHANS;
+
+ if (lradc->soc == IMX23_LRADC) {
+ iio->channels = mx23_lradc_chan_spec;
+ iio->num_channels = ARRAY_SIZE(mx23_lradc_chan_spec);
+ irq_name = mx23_lradc_adc_irq_names;
+ n = ARRAY_SIZE(mx23_lradc_adc_irq_names);
+ } else {
+ iio->channels = mx28_lradc_chan_spec;
+ iio->num_channels = ARRAY_SIZE(mx28_lradc_chan_spec);
+ irq_name = mx28_lradc_adc_irq_names;
+ n = ARRAY_SIZE(mx28_lradc_adc_irq_names);
+ }
+
+ ret = stmp_reset_block(adc->base);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < n; i++) {
+ irq = platform_get_irq_byname(pdev, irq_name[i]);
+ if (irq < 0)
+ return irq;
+
+ virq = irq_of_parse_and_map(dev->parent->of_node, irq);
+
+ ret = devm_request_irq(dev, virq, mxs_lradc_adc_handle_irq,
+ 0, irq_name[i], iio);
+ if (ret)
+ return ret;
+ }
+
+ ret = mxs_lradc_adc_trigger_init(iio);
+ if (ret)
+ goto err_trig;
+
+ ret = iio_triggered_buffer_setup(iio, &iio_pollfunc_store_time,
+ &mxs_lradc_adc_trigger_handler,
+ &mxs_lradc_adc_buffer_ops);
+ if (ret)
+ return ret;
+
+ adc->vref_mv = mxs_lradc_adc_vref_mv[lradc->soc];
+
+ /* Populate available ADC input ranges */
+ for (i = 0; i < LRADC_MAX_TOTAL_CHANS; i++) {
+ for (s = 0; s < ARRAY_SIZE(adc->scale_avail[i]); s++) {
+ /*
+ * [s=0] = optional divider by two disabled (default)
+ * [s=1] = optional divider by two enabled
+ *
+ * The scale is calculated by doing:
+ * Vref >> (realbits - s)
+ * which multiplies by two on the second component
+ * of the array.
+ */
+ scale_uv = ((u64)adc->vref_mv[i] * 100000000) >>
+ (LRADC_RESOLUTION - s);
+ adc->scale_avail[i][s].nano =
+ do_div(scale_uv, 100000000) * 10;
+ adc->scale_avail[i][s].integer = scale_uv;
+ }
+ }
+
+ /* Configure the hardware. */
+ mxs_lradc_adc_hw_init(adc);
+
+ /* Register IIO device. */
+ ret = iio_device_register(iio);
+ if (ret) {
+ dev_err(dev, "Failed to register IIO device\n");
+ goto err_dev;
+ }
+
+ return 0;
+
+err_dev:
+ mxs_lradc_adc_hw_stop(adc);
+ mxs_lradc_adc_trigger_remove(iio);
+err_trig:
+ iio_triggered_buffer_cleanup(iio);
+ return ret;
+}
+
+static int mxs_lradc_adc_remove(struct platform_device *pdev)
+{
+ struct iio_dev *iio = platform_get_drvdata(pdev);
+ struct mxs_lradc_adc *adc = iio_priv(iio);
+
+ iio_device_unregister(iio);
+ mxs_lradc_adc_hw_stop(adc);
+ mxs_lradc_adc_trigger_remove(iio);
+ iio_triggered_buffer_cleanup(iio);
+
+ return 0;
+}
+
+static struct platform_driver mxs_lradc_adc_driver = {
+ .driver = {
+ .name = "mxs-lradc-adc",
+ },
+ .probe = mxs_lradc_adc_probe,
+ .remove = mxs_lradc_adc_remove,
+};
+module_platform_driver(mxs_lradc_adc_driver);
+
+MODULE_AUTHOR("Marek Vasut <marex@denx.de>");
+MODULE_DESCRIPTION("Freescale MXS LRADC driver general purpose ADC driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:mxs-lradc-adc");
diff --git a/drivers/iio/adc/mxs-lradc.c b/drivers/iio/adc/mxs-lradc.c
deleted file mode 100644
index b84d37c..0000000
--- a/drivers/iio/adc/mxs-lradc.c
+++ /dev/null
@@ -1,1750 +0,0 @@
-/*
- * Freescale MXS LRADC driver
- *
- * Copyright (c) 2012 DENX Software Engineering, GmbH.
- * Marek Vasut <marex@denx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/bitops.h>
-#include <linux/clk.h>
-#include <linux/completion.h>
-#include <linux/device.h>
-#include <linux/err.h>
-#include <linux/input.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/mutex.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-#include <linux/stmp_device.h>
-#include <linux/sysfs.h>
-
-#include <linux/iio/buffer.h>
-#include <linux/iio/iio.h>
-#include <linux/iio/trigger.h>
-#include <linux/iio/trigger_consumer.h>
-#include <linux/iio/triggered_buffer.h>
-#include <linux/iio/sysfs.h>
-
-#define DRIVER_NAME "mxs-lradc"
-
-#define LRADC_MAX_DELAY_CHANS 4
-#define LRADC_MAX_MAPPED_CHANS 8
-#define LRADC_MAX_TOTAL_CHANS 16
-
-#define LRADC_DELAY_TIMER_HZ 2000
-
-/*
- * Make this runtime configurable if necessary. Currently, if the buffered mode
- * is enabled, the LRADC takes LRADC_DELAY_TIMER_LOOP samples of data before
- * triggering IRQ. The sampling happens every (LRADC_DELAY_TIMER_PER / 2000)
- * seconds. The result is that the samples arrive every 500mS.
- */
-#define LRADC_DELAY_TIMER_PER 200
-#define LRADC_DELAY_TIMER_LOOP 5
-
-/*
- * Once the pen touches the touchscreen, the touchscreen switches from
- * IRQ-driven mode to polling mode to prevent interrupt storm. The polling
- * is realized by worker thread, which is called every 20 or so milliseconds.
- * This gives the touchscreen enough fluency and does not strain the system
- * too much.
- */
-#define LRADC_TS_SAMPLE_DELAY_MS 5
-
-/*
- * The LRADC reads the following amount of samples from each touchscreen
- * channel and the driver then computes average of these.
- */
-#define LRADC_TS_SAMPLE_AMOUNT 4
-
-enum mxs_lradc_id {
- IMX23_LRADC,
- IMX28_LRADC,
-};
-
-static const char * const mx23_lradc_irq_names[] = {
- "mxs-lradc-touchscreen",
- "mxs-lradc-channel0",
- "mxs-lradc-channel1",
- "mxs-lradc-channel2",
- "mxs-lradc-channel3",
- "mxs-lradc-channel4",
- "mxs-lradc-channel5",
- "mxs-lradc-channel6",
- "mxs-lradc-channel7",
-};
-
-static const char * const mx28_lradc_irq_names[] = {
- "mxs-lradc-touchscreen",
- "mxs-lradc-thresh0",
- "mxs-lradc-thresh1",
- "mxs-lradc-channel0",
- "mxs-lradc-channel1",
- "mxs-lradc-channel2",
- "mxs-lradc-channel3",
- "mxs-lradc-channel4",
- "mxs-lradc-channel5",
- "mxs-lradc-channel6",
- "mxs-lradc-channel7",
- "mxs-lradc-button0",
- "mxs-lradc-button1",
-};
-
-struct mxs_lradc_of_config {
- const int irq_count;
- const char * const *irq_name;
- const u32 *vref_mv;
-};
-
-#define VREF_MV_BASE 1850
-
-static const u32 mx23_vref_mv[LRADC_MAX_TOTAL_CHANS] = {
- VREF_MV_BASE, /* CH0 */
- VREF_MV_BASE, /* CH1 */
- VREF_MV_BASE, /* CH2 */
- VREF_MV_BASE, /* CH3 */
- VREF_MV_BASE, /* CH4 */
- VREF_MV_BASE, /* CH5 */
- VREF_MV_BASE * 2, /* CH6 VDDIO */
- VREF_MV_BASE * 4, /* CH7 VBATT */
- VREF_MV_BASE, /* CH8 Temp sense 0 */
- VREF_MV_BASE, /* CH9 Temp sense 1 */
- VREF_MV_BASE, /* CH10 */
- VREF_MV_BASE, /* CH11 */
- VREF_MV_BASE, /* CH12 USB_DP */
- VREF_MV_BASE, /* CH13 USB_DN */
- VREF_MV_BASE, /* CH14 VBG */
- VREF_MV_BASE * 4, /* CH15 VDD5V */
-};
-
-static const u32 mx28_vref_mv[LRADC_MAX_TOTAL_CHANS] = {
- VREF_MV_BASE, /* CH0 */
- VREF_MV_BASE, /* CH1 */
- VREF_MV_BASE, /* CH2 */
- VREF_MV_BASE, /* CH3 */
- VREF_MV_BASE, /* CH4 */
- VREF_MV_BASE, /* CH5 */
- VREF_MV_BASE, /* CH6 */
- VREF_MV_BASE * 4, /* CH7 VBATT */
- VREF_MV_BASE, /* CH8 Temp sense 0 */
- VREF_MV_BASE, /* CH9 Temp sense 1 */
- VREF_MV_BASE * 2, /* CH10 VDDIO */
- VREF_MV_BASE, /* CH11 VTH */
- VREF_MV_BASE * 2, /* CH12 VDDA */
- VREF_MV_BASE, /* CH13 VDDD */
- VREF_MV_BASE, /* CH14 VBG */
- VREF_MV_BASE * 4, /* CH15 VDD5V */
-};
-
-static const struct mxs_lradc_of_config mxs_lradc_of_config[] = {
- [IMX23_LRADC] = {
- .irq_count = ARRAY_SIZE(mx23_lradc_irq_names),
- .irq_name = mx23_lradc_irq_names,
- .vref_mv = mx23_vref_mv,
- },
- [IMX28_LRADC] = {
- .irq_count = ARRAY_SIZE(mx28_lradc_irq_names),
- .irq_name = mx28_lradc_irq_names,
- .vref_mv = mx28_vref_mv,
- },
-};
-
-enum mxs_lradc_ts {
- MXS_LRADC_TOUCHSCREEN_NONE = 0,
- MXS_LRADC_TOUCHSCREEN_4WIRE,
- MXS_LRADC_TOUCHSCREEN_5WIRE,
-};
-
-/*
- * Touchscreen handling
- */
-enum lradc_ts_plate {
- LRADC_TOUCH = 0,
- LRADC_SAMPLE_X,
- LRADC_SAMPLE_Y,
- LRADC_SAMPLE_PRESSURE,
- LRADC_SAMPLE_VALID,
-};
-
-enum mxs_lradc_divbytwo {
- MXS_LRADC_DIV_DISABLED = 0,
- MXS_LRADC_DIV_ENABLED,
-};
-
-struct mxs_lradc_scale {
- unsigned int integer;
- unsigned int nano;
-};
-
-struct mxs_lradc {
- struct device *dev;
- void __iomem *base;
- int irq[13];
-
- struct clk *clk;
-
- u32 *buffer;
- struct iio_trigger *trig;
-
- struct mutex lock;
-
- struct completion completion;
-
- const u32 *vref_mv;
- struct mxs_lradc_scale scale_avail[LRADC_MAX_TOTAL_CHANS][2];
- unsigned long is_divided;
-
- /*
- * When the touchscreen is enabled, we give it two private virtual
- * channels: #6 and #7. This means that only 6 virtual channels (instead
- * of 8) will be available for buffered capture.
- */
-#define TOUCHSCREEN_VCHANNEL1 7
-#define TOUCHSCREEN_VCHANNEL2 6
-#define BUFFER_VCHANS_LIMITED 0x3f
-#define BUFFER_VCHANS_ALL 0xff
- u8 buffer_vchans;
-
- /*
- * Furthermore, certain LRADC channels are shared between touchscreen
- * and/or touch-buttons and generic LRADC block. Therefore when using
- * either of these, these channels are not available for the regular
- * sampling. The shared channels are as follows:
- *
- * CH0 -- Touch button #0
- * CH1 -- Touch button #1
- * CH2 -- Touch screen XPUL
- * CH3 -- Touch screen YPLL
- * CH4 -- Touch screen XNUL
- * CH5 -- Touch screen YNLR
- * CH6 -- Touch screen WIPER (5-wire only)
- *
- * The bit fields below represents which parts of the LRADC block are
- * switched into special mode of operation. These channels can not
- * be sampled as regular LRADC channels. The driver will refuse any
- * attempt to sample these channels.
- */
-#define CHAN_MASK_TOUCHBUTTON (BIT(1) | BIT(0))
-#define CHAN_MASK_TOUCHSCREEN_4WIRE (0xf << 2)
-#define CHAN_MASK_TOUCHSCREEN_5WIRE (0x1f << 2)
- enum mxs_lradc_ts use_touchscreen;
- bool use_touchbutton;
-
- struct input_dev *ts_input;
-
- enum mxs_lradc_id soc;
- enum lradc_ts_plate cur_plate; /* state machine */
- bool ts_valid;
- unsigned ts_x_pos;
- unsigned ts_y_pos;
- unsigned ts_pressure;
-
- /* handle touchscreen's physical behaviour */
- /* samples per coordinate */
- unsigned over_sample_cnt;
- /* time clocks between samples */
- unsigned over_sample_delay;
- /* time in clocks to wait after the plates where switched */
- unsigned settling_delay;
-};
-
-#define LRADC_CTRL0 0x00
-# define LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE BIT(23)
-# define LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE BIT(22)
-# define LRADC_CTRL0_MX28_YNNSW /* YM */ BIT(21)
-# define LRADC_CTRL0_MX28_YPNSW /* YP */ BIT(20)
-# define LRADC_CTRL0_MX28_YPPSW /* YP */ BIT(19)
-# define LRADC_CTRL0_MX28_XNNSW /* XM */ BIT(18)
-# define LRADC_CTRL0_MX28_XNPSW /* XM */ BIT(17)
-# define LRADC_CTRL0_MX28_XPPSW /* XP */ BIT(16)
-
-# define LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE BIT(20)
-# define LRADC_CTRL0_MX23_YM BIT(19)
-# define LRADC_CTRL0_MX23_XM BIT(18)
-# define LRADC_CTRL0_MX23_YP BIT(17)
-# define LRADC_CTRL0_MX23_XP BIT(16)
-
-# define LRADC_CTRL0_MX28_PLATE_MASK \
- (LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
- LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
- LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
- LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
-
-# define LRADC_CTRL0_MX23_PLATE_MASK \
- (LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE | \
- LRADC_CTRL0_MX23_YM | LRADC_CTRL0_MX23_XM | \
- LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XP)
-
-#define LRADC_CTRL1 0x10
-#define LRADC_CTRL1_TOUCH_DETECT_IRQ_EN BIT(24)
-#define LRADC_CTRL1_LRADC_IRQ_EN(n) (1 << ((n) + 16))
-#define LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK (0x1fff << 16)
-#define LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK (0x01ff << 16)
-#define LRADC_CTRL1_LRADC_IRQ_EN_OFFSET 16
-#define LRADC_CTRL1_TOUCH_DETECT_IRQ BIT(8)
-#define LRADC_CTRL1_LRADC_IRQ(n) (1 << (n))
-#define LRADC_CTRL1_MX28_LRADC_IRQ_MASK 0x1fff
-#define LRADC_CTRL1_MX23_LRADC_IRQ_MASK 0x01ff
-#define LRADC_CTRL1_LRADC_IRQ_OFFSET 0
-
-#define LRADC_CTRL2 0x20
-#define LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET 24
-#define LRADC_CTRL2_TEMPSENSE_PWD BIT(15)
-
-#define LRADC_STATUS 0x40
-#define LRADC_STATUS_TOUCH_DETECT_RAW BIT(0)
-
-#define LRADC_CH(n) (0x50 + (0x10 * (n)))
-#define LRADC_CH_ACCUMULATE BIT(29)
-#define LRADC_CH_NUM_SAMPLES_MASK (0x1f << 24)
-#define LRADC_CH_NUM_SAMPLES_OFFSET 24
-#define LRADC_CH_NUM_SAMPLES(x) \
- ((x) << LRADC_CH_NUM_SAMPLES_OFFSET)
-#define LRADC_CH_VALUE_MASK 0x3ffff
-#define LRADC_CH_VALUE_OFFSET 0
-
-#define LRADC_DELAY(n) (0xd0 + (0x10 * (n)))
-#define LRADC_DELAY_TRIGGER_LRADCS_MASK (0xffUL << 24)
-#define LRADC_DELAY_TRIGGER_LRADCS_OFFSET 24
-#define LRADC_DELAY_TRIGGER(x) \
- (((x) << LRADC_DELAY_TRIGGER_LRADCS_OFFSET) & \
- LRADC_DELAY_TRIGGER_LRADCS_MASK)
-#define LRADC_DELAY_KICK BIT(20)
-#define LRADC_DELAY_TRIGGER_DELAYS_MASK (0xf << 16)
-#define LRADC_DELAY_TRIGGER_DELAYS_OFFSET 16
-#define LRADC_DELAY_TRIGGER_DELAYS(x) \
- (((x) << LRADC_DELAY_TRIGGER_DELAYS_OFFSET) & \
- LRADC_DELAY_TRIGGER_DELAYS_MASK)
-#define LRADC_DELAY_LOOP_COUNT_MASK (0x1f << 11)
-#define LRADC_DELAY_LOOP_COUNT_OFFSET 11
-#define LRADC_DELAY_LOOP(x) \
- (((x) << LRADC_DELAY_LOOP_COUNT_OFFSET) & \
- LRADC_DELAY_LOOP_COUNT_MASK)
-#define LRADC_DELAY_DELAY_MASK 0x7ff
-#define LRADC_DELAY_DELAY_OFFSET 0
-#define LRADC_DELAY_DELAY(x) \
- (((x) << LRADC_DELAY_DELAY_OFFSET) & \
- LRADC_DELAY_DELAY_MASK)
-
-#define LRADC_CTRL4 0x140
-#define LRADC_CTRL4_LRADCSELECT_MASK(n) (0xf << ((n) * 4))
-#define LRADC_CTRL4_LRADCSELECT_OFFSET(n) ((n) * 4)
-#define LRADC_CTRL4_LRADCSELECT(n, x) \
- (((x) << LRADC_CTRL4_LRADCSELECT_OFFSET(n)) & \
- LRADC_CTRL4_LRADCSELECT_MASK(n))
-
-#define LRADC_RESOLUTION 12
-#define LRADC_SINGLE_SAMPLE_MASK ((1 << LRADC_RESOLUTION) - 1)
-
-static void mxs_lradc_reg_set(struct mxs_lradc *lradc, u32 val, u32 reg)
-{
- writel(val, lradc->base + reg + STMP_OFFSET_REG_SET);
-}
-
-static void mxs_lradc_reg_clear(struct mxs_lradc *lradc, u32 val, u32 reg)
-{
- writel(val, lradc->base + reg + STMP_OFFSET_REG_CLR);
-}
-
-static void mxs_lradc_reg_wrt(struct mxs_lradc *lradc, u32 val, u32 reg)
-{
- writel(val, lradc->base + reg);
-}
-
-static u32 mxs_lradc_plate_mask(struct mxs_lradc *lradc)
-{
- if (lradc->soc == IMX23_LRADC)
- return LRADC_CTRL0_MX23_PLATE_MASK;
- return LRADC_CTRL0_MX28_PLATE_MASK;
-}
-
-static u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
-{
- if (lradc->soc == IMX23_LRADC)
- return LRADC_CTRL1_MX23_LRADC_IRQ_MASK;
- return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
-}
-
-static u32 mxs_lradc_touch_detect_bit(struct mxs_lradc *lradc)
-{
- if (lradc->soc == IMX23_LRADC)
- return LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE;
- return LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE;
-}
-
-static u32 mxs_lradc_drive_x_plate(struct mxs_lradc *lradc)
-{
- if (lradc->soc == IMX23_LRADC)
- return LRADC_CTRL0_MX23_XP | LRADC_CTRL0_MX23_XM;
- return LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW;
-}
-
-static u32 mxs_lradc_drive_y_plate(struct mxs_lradc *lradc)
-{
- if (lradc->soc == IMX23_LRADC)
- return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_YM;
- return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW;
-}
-
-static u32 mxs_lradc_drive_pressure(struct mxs_lradc *lradc)
-{
- if (lradc->soc == IMX23_LRADC)
- return LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM;
- return LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW;
-}
-
-static bool mxs_lradc_check_touch_event(struct mxs_lradc *lradc)
-{
- return !!(readl(lradc->base + LRADC_STATUS) &
- LRADC_STATUS_TOUCH_DETECT_RAW);
-}
-
-static void mxs_lradc_map_channel(struct mxs_lradc *lradc, unsigned vch,
- unsigned ch)
-{
- mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(vch),
- LRADC_CTRL4);
- mxs_lradc_reg_set(lradc, LRADC_CTRL4_LRADCSELECT(vch, ch), LRADC_CTRL4);
-}
-
-static void mxs_lradc_setup_ts_channel(struct mxs_lradc *lradc, unsigned ch)
-{
- /*
- * prepare for oversampling conversion
- *
- * from the datasheet:
- * "The ACCUMULATE bit in the appropriate channel register
- * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
- * otherwise, the IRQs will not fire."
- */
- mxs_lradc_reg_wrt(lradc, LRADC_CH_ACCUMULATE |
- LRADC_CH_NUM_SAMPLES(lradc->over_sample_cnt - 1),
- LRADC_CH(ch));
-
- /*
- * from the datasheet:
- * "Software must clear this register in preparation for a
- * multi-cycle accumulation.
- */
- mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch));
-
- /*
- * prepare the delay/loop unit according to the oversampling count
- *
- * from the datasheet:
- * "The DELAY fields in HW_LRADC_DELAY0, HW_LRADC_DELAY1,
- * HW_LRADC_DELAY2, and HW_LRADC_DELAY3 must be non-zero; otherwise,
- * the LRADC will not trigger the delay group."
- */
- mxs_lradc_reg_wrt(lradc, LRADC_DELAY_TRIGGER(1 << ch) |
- LRADC_DELAY_TRIGGER_DELAYS(0) |
- LRADC_DELAY_LOOP(lradc->over_sample_cnt - 1) |
- LRADC_DELAY_DELAY(lradc->over_sample_delay - 1),
- LRADC_DELAY(3));
-
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(ch), LRADC_CTRL1);
-
- /*
- * after changing the touchscreen plates setting
- * the signals need some initial time to settle. Start the
- * SoC's delay unit and start the conversion later
- * and automatically.
- */
- mxs_lradc_reg_wrt(
- lradc,
- LRADC_DELAY_TRIGGER(0) | /* don't trigger ADC */
- LRADC_DELAY_TRIGGER_DELAYS(BIT(3)) | /* trigger DELAY unit#3 */
- LRADC_DELAY_KICK |
- LRADC_DELAY_DELAY(lradc->settling_delay),
- LRADC_DELAY(2));
-}
-
-/*
- * Pressure detection is special:
- * We want to do both required measurements for the pressure detection in
- * one turn. Use the hardware features to chain both conversions and let the
- * hardware report one interrupt if both conversions are done
- */
-static void mxs_lradc_setup_ts_pressure(struct mxs_lradc *lradc, unsigned ch1,
- unsigned ch2)
-{
- u32 reg;
-
- /*
- * prepare for oversampling conversion
- *
- * from the datasheet:
- * "The ACCUMULATE bit in the appropriate channel register
- * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
- * otherwise, the IRQs will not fire."
- */
- reg = LRADC_CH_ACCUMULATE |
- LRADC_CH_NUM_SAMPLES(lradc->over_sample_cnt - 1);
- mxs_lradc_reg_wrt(lradc, reg, LRADC_CH(ch1));
- mxs_lradc_reg_wrt(lradc, reg, LRADC_CH(ch2));
-
- /*
- * from the datasheet:
- * "Software must clear this register in preparation for a
- * multi-cycle accumulation.
- */
- mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch1));
- mxs_lradc_reg_clear(lradc, LRADC_CH_VALUE_MASK, LRADC_CH(ch2));
-
- /* prepare the delay/loop unit according to the oversampling count */
- mxs_lradc_reg_wrt(
- lradc,
- LRADC_DELAY_TRIGGER(1 << ch1) |
- LRADC_DELAY_TRIGGER(1 << ch2) | /* start both channels */
- LRADC_DELAY_TRIGGER_DELAYS(0) |
- LRADC_DELAY_LOOP(lradc->over_sample_cnt - 1) |
- LRADC_DELAY_DELAY(lradc->over_sample_delay - 1),
- LRADC_DELAY(3));
-
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ(ch2), LRADC_CTRL1);
-
- /*
- * after changing the touchscreen plates setting
- * the signals need some initial time to settle. Start the
- * SoC's delay unit and start the conversion later
- * and automatically.
- */
- mxs_lradc_reg_wrt(
- lradc,
- LRADC_DELAY_TRIGGER(0) | /* don't trigger ADC */
- LRADC_DELAY_TRIGGER_DELAYS(BIT(3)) | /* trigger DELAY unit#3 */
- LRADC_DELAY_KICK |
- LRADC_DELAY_DELAY(lradc->settling_delay), LRADC_DELAY(2));
-}
-
-static unsigned mxs_lradc_read_raw_channel(struct mxs_lradc *lradc,
- unsigned channel)
-{
- u32 reg;
- unsigned num_samples, val;
-
- reg = readl(lradc->base + LRADC_CH(channel));
- if (reg & LRADC_CH_ACCUMULATE)
- num_samples = lradc->over_sample_cnt;
- else
- num_samples = 1;
-
- val = (reg & LRADC_CH_VALUE_MASK) >> LRADC_CH_VALUE_OFFSET;
- return val / num_samples;
-}
-
-static unsigned mxs_lradc_read_ts_pressure(struct mxs_lradc *lradc,
- unsigned ch1, unsigned ch2)
-{
- u32 reg, mask;
- unsigned pressure, m1, m2;
-
- mask = LRADC_CTRL1_LRADC_IRQ(ch1) | LRADC_CTRL1_LRADC_IRQ(ch2);
- reg = readl(lradc->base + LRADC_CTRL1) & mask;
-
- while (reg != mask) {
- reg = readl(lradc->base + LRADC_CTRL1) & mask;
- dev_dbg(lradc->dev, "One channel is still busy: %X\n", reg);
- }
-
- m1 = mxs_lradc_read_raw_channel(lradc, ch1);
- m2 = mxs_lradc_read_raw_channel(lradc, ch2);
-
- if (m2 == 0) {
- dev_warn(lradc->dev, "Cannot calculate pressure\n");
- return 1 << (LRADC_RESOLUTION - 1);
- }
-
- /* simply scale the value from 0 ... max ADC resolution */
- pressure = m1;
- pressure *= (1 << LRADC_RESOLUTION);
- pressure /= m2;
-
- dev_dbg(lradc->dev, "Pressure = %u\n", pressure);
- return pressure;
-}
-
-#define TS_CH_XP 2
-#define TS_CH_YP 3
-#define TS_CH_XM 4
-#define TS_CH_YM 5
-
-/*
- * YP(open)--+-------------+
- * | |--+
- * | | |
- * YM(-)--+-------------+ |
- * +--------------+
- * | |
- * XP(weak+) XM(open)
- *
- * "weak+" means 200k Ohm VDDIO
- * (-) means GND
- */
-static void mxs_lradc_setup_touch_detection(struct mxs_lradc *lradc)
-{
- /*
- * In order to detect a touch event the 'touch detect enable' bit
- * enables:
- * - a weak pullup to the X+ connector
- * - a strong ground at the Y- connector
- */
- mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
- mxs_lradc_reg_set(lradc, mxs_lradc_touch_detect_bit(lradc),
- LRADC_CTRL0);
-}
-
-/*
- * YP(meas)--+-------------+
- * | |--+
- * | | |
- * YM(open)--+-------------+ |
- * +--------------+
- * | |
- * XP(+) XM(-)
- *
- * (+) means here 1.85 V
- * (-) means here GND
- */
-static void mxs_lradc_prepare_x_pos(struct mxs_lradc *lradc)
-{
- mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
- mxs_lradc_reg_set(lradc, mxs_lradc_drive_x_plate(lradc), LRADC_CTRL0);
-
- lradc->cur_plate = LRADC_SAMPLE_X;
- mxs_lradc_map_channel(lradc, TOUCHSCREEN_VCHANNEL1, TS_CH_YP);
- mxs_lradc_setup_ts_channel(lradc, TOUCHSCREEN_VCHANNEL1);
-}
-
-/*
- * YP(+)--+-------------+
- * | |--+
- * | | |
- * YM(-)--+-------------+ |
- * +--------------+
- * | |
- * XP(open) XM(meas)
- *
- * (+) means here 1.85 V
- * (-) means here GND
- */
-static void mxs_lradc_prepare_y_pos(struct mxs_lradc *lradc)
-{
- mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
- mxs_lradc_reg_set(lradc, mxs_lradc_drive_y_plate(lradc), LRADC_CTRL0);
-
- lradc->cur_plate = LRADC_SAMPLE_Y;
- mxs_lradc_map_channel(lradc, TOUCHSCREEN_VCHANNEL1, TS_CH_XM);
- mxs_lradc_setup_ts_channel(lradc, TOUCHSCREEN_VCHANNEL1);
-}
-
-/*
- * YP(+)--+-------------+
- * | |--+
- * | | |
- * YM(meas)--+-------------+ |
- * +--------------+
- * | |
- * XP(meas) XM(-)
- *
- * (+) means here 1.85 V
- * (-) means here GND
- */
-static void mxs_lradc_prepare_pressure(struct mxs_lradc *lradc)
-{
- mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
- mxs_lradc_reg_set(lradc, mxs_lradc_drive_pressure(lradc), LRADC_CTRL0);
-
- lradc->cur_plate = LRADC_SAMPLE_PRESSURE;
- mxs_lradc_map_channel(lradc, TOUCHSCREEN_VCHANNEL1, TS_CH_YM);
- mxs_lradc_map_channel(lradc, TOUCHSCREEN_VCHANNEL2, TS_CH_XP);
- mxs_lradc_setup_ts_pressure(lradc, TOUCHSCREEN_VCHANNEL2,
- TOUCHSCREEN_VCHANNEL1);
-}
-
-static void mxs_lradc_enable_touch_detection(struct mxs_lradc *lradc)
-{
- /* Configure the touchscreen type */
- if (lradc->soc == IMX28_LRADC) {
- mxs_lradc_reg_clear(lradc, LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
- LRADC_CTRL0);
-
- if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
- mxs_lradc_reg_set(lradc,
- LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
- LRADC_CTRL0);
- }
-
- mxs_lradc_setup_touch_detection(lradc);
-
- lradc->cur_plate = LRADC_TOUCH;
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ |
- LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
- mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
-}
-
-static void mxs_lradc_start_touch_event(struct mxs_lradc *lradc)
-{
- mxs_lradc_reg_clear(lradc,
- LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
- LRADC_CTRL1);
- mxs_lradc_reg_set(lradc,
- LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1),
- LRADC_CTRL1);
- /*
- * start with the Y-pos, because it uses nearly the same plate
- * settings like the touch detection
- */
- mxs_lradc_prepare_y_pos(lradc);
-}
-
-static void mxs_lradc_report_ts_event(struct mxs_lradc *lradc)
-{
- input_report_abs(lradc->ts_input, ABS_X, lradc->ts_x_pos);
- input_report_abs(lradc->ts_input, ABS_Y, lradc->ts_y_pos);
- input_report_abs(lradc->ts_input, ABS_PRESSURE, lradc->ts_pressure);
- input_report_key(lradc->ts_input, BTN_TOUCH, 1);
- input_sync(lradc->ts_input);
-}
-
-static void mxs_lradc_complete_touch_event(struct mxs_lradc *lradc)
-{
- mxs_lradc_setup_touch_detection(lradc);
- lradc->cur_plate = LRADC_SAMPLE_VALID;
- /*
- * start a dummy conversion to burn time to settle the signals
- * note: we are not interested in the conversion's value
- */
- mxs_lradc_reg_wrt(lradc, 0, LRADC_CH(TOUCHSCREEN_VCHANNEL1));
- mxs_lradc_reg_clear(lradc,
- LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
- LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2),
- LRADC_CTRL1);
- mxs_lradc_reg_wrt(
- lradc,
- LRADC_DELAY_TRIGGER(1 << TOUCHSCREEN_VCHANNEL1) |
- LRADC_DELAY_KICK | LRADC_DELAY_DELAY(10), /* waste 5 ms */
- LRADC_DELAY(2));
-}
-
-/*
- * in order to avoid false measurements, report only samples where
- * the surface is still touched after the position measurement
- */
-static void mxs_lradc_finish_touch_event(struct mxs_lradc *lradc, bool valid)
-{
- /* if it is still touched, report the sample */
- if (valid && mxs_lradc_check_touch_event(lradc)) {
- lradc->ts_valid = true;
- mxs_lradc_report_ts_event(lradc);
- }
-
- /* if it is even still touched, continue with the next measurement */
- if (mxs_lradc_check_touch_event(lradc)) {
- mxs_lradc_prepare_y_pos(lradc);
- return;
- }
-
- if (lradc->ts_valid) {
- /* signal the release */
- lradc->ts_valid = false;
- input_report_key(lradc->ts_input, BTN_TOUCH, 0);
- input_sync(lradc->ts_input);
- }
-
- /* if it is released, wait for the next touch via IRQ */
- lradc->cur_plate = LRADC_TOUCH;
- mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(2));
- mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3));
- mxs_lradc_reg_clear(lradc,
- LRADC_CTRL1_TOUCH_DETECT_IRQ |
- LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1) |
- LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1),
- LRADC_CTRL1);
- mxs_lradc_reg_set(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN, LRADC_CTRL1);
-}
-
-/* touchscreen's state machine */
-static void mxs_lradc_handle_touch(struct mxs_lradc *lradc)
-{
- switch (lradc->cur_plate) {
- case LRADC_TOUCH:
- if (mxs_lradc_check_touch_event(lradc))
- mxs_lradc_start_touch_event(lradc);
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ,
- LRADC_CTRL1);
- return;
-
- case LRADC_SAMPLE_Y:
- lradc->ts_y_pos =
- mxs_lradc_read_raw_channel(lradc,
- TOUCHSCREEN_VCHANNEL1);
- mxs_lradc_prepare_x_pos(lradc);
- return;
-
- case LRADC_SAMPLE_X:
- lradc->ts_x_pos =
- mxs_lradc_read_raw_channel(lradc,
- TOUCHSCREEN_VCHANNEL1);
- mxs_lradc_prepare_pressure(lradc);
- return;
-
- case LRADC_SAMPLE_PRESSURE:
- lradc->ts_pressure =
- mxs_lradc_read_ts_pressure(lradc,
- TOUCHSCREEN_VCHANNEL2,
- TOUCHSCREEN_VCHANNEL1);
- mxs_lradc_complete_touch_event(lradc);
- return;
-
- case LRADC_SAMPLE_VALID:
- mxs_lradc_finish_touch_event(lradc, 1);
- break;
- }
-}
-
-/*
- * Raw I/O operations
- */
-static int mxs_lradc_read_single(struct iio_dev *iio_dev, int chan, int *val)
-{
- struct mxs_lradc *lradc = iio_priv(iio_dev);
- int ret;
-
- /*
- * See if there is no buffered operation in progress. If there is, simply
- * bail out. This can be improved to support both buffered and raw IO at
- * the same time, yet the code becomes horribly complicated. Therefore I
- * applied KISS principle here.
- */
- ret = mutex_trylock(&lradc->lock);
- if (!ret)
- return -EBUSY;
-
- reinit_completion(&lradc->completion);
-
- /*
- * No buffered operation in progress, map the channel and trigger it.
- * Virtual channel 0 is always used here as the others are always not
- * used if doing raw sampling.
- */
- if (lradc->soc == IMX28_LRADC)
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0),
- LRADC_CTRL1);
- mxs_lradc_reg_clear(lradc, 0x1, LRADC_CTRL0);
-
- /* Enable / disable the divider per requirement */
- if (test_bit(chan, &lradc->is_divided))
- mxs_lradc_reg_set(lradc,
- 1 << LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET,
- LRADC_CTRL2);
- else
- mxs_lradc_reg_clear(lradc,
- 1 << LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET,
- LRADC_CTRL2);
-
- /* Clean the slot's previous content, then set new one. */
- mxs_lradc_reg_clear(lradc, LRADC_CTRL4_LRADCSELECT_MASK(0),
- LRADC_CTRL4);
- mxs_lradc_reg_set(lradc, chan, LRADC_CTRL4);
-
- mxs_lradc_reg_wrt(lradc, 0, LRADC_CH(0));
-
- /* Enable the IRQ and start sampling the channel. */
- mxs_lradc_reg_set(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1);
- mxs_lradc_reg_set(lradc, BIT(0), LRADC_CTRL0);
-
- /* Wait for completion on the channel, 1 second max. */
- ret = wait_for_completion_killable_timeout(&lradc->completion, HZ);
- if (!ret)
- ret = -ETIMEDOUT;
- if (ret < 0)
- goto err;
-
- /* Read the data. */
- *val = readl(lradc->base + LRADC_CH(0)) & LRADC_CH_VALUE_MASK;
- ret = IIO_VAL_INT;
-
-err:
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_LRADC_IRQ_EN(0), LRADC_CTRL1);
-
- mutex_unlock(&lradc->lock);
-
- return ret;
-}
-
-static int mxs_lradc_read_temp(struct iio_dev *iio_dev, int *val)
-{
- int ret, min, max;
-
- ret = mxs_lradc_read_single(iio_dev, 8, &min);
- if (ret != IIO_VAL_INT)
- return ret;
-
- ret = mxs_lradc_read_single(iio_dev, 9, &max);
- if (ret != IIO_VAL_INT)
- return ret;
-
- *val = max - min;
-
- return IIO_VAL_INT;
-}
-
-static int mxs_lradc_read_raw(struct iio_dev *iio_dev,
- const struct iio_chan_spec *chan,
- int *val, int *val2, long m)
-{
- struct mxs_lradc *lradc = iio_priv(iio_dev);
-
- switch (m) {
- case IIO_CHAN_INFO_RAW:
- if (chan->type == IIO_TEMP)
- return mxs_lradc_read_temp(iio_dev, val);
-
- return mxs_lradc_read_single(iio_dev, chan->channel, val);
-
- case IIO_CHAN_INFO_SCALE:
- if (chan->type == IIO_TEMP) {
- /*
- * From the datasheet, we have to multiply by 1.012 and
- * divide by 4
- */
- *val = 0;
- *val2 = 253000;
- return IIO_VAL_INT_PLUS_MICRO;
- }
-
- *val = lradc->vref_mv[chan->channel];
- *val2 = chan->scan_type.realbits -
- test_bit(chan->channel, &lradc->is_divided);
- return IIO_VAL_FRACTIONAL_LOG2;
-
- case IIO_CHAN_INFO_OFFSET:
- if (chan->type == IIO_TEMP) {
- /*
- * The calculated value from the ADC is in Kelvin, we
- * want Celsius for hwmon so the offset is -273.15
- * The offset is applied before scaling so it is
- * actually -213.15 * 4 / 1.012 = -1079.644268
- */
- *val = -1079;
- *val2 = 644268;
-
- return IIO_VAL_INT_PLUS_MICRO;
- }
-
- return -EINVAL;
-
- default:
- break;
- }
-
- return -EINVAL;
-}
-
-static int mxs_lradc_write_raw(struct iio_dev *iio_dev,
- const struct iio_chan_spec *chan,
- int val, int val2, long m)
-{
- struct mxs_lradc *lradc = iio_priv(iio_dev);
- struct mxs_lradc_scale *scale_avail =
- lradc->scale_avail[chan->channel];
- int ret;
-
- ret = mutex_trylock(&lradc->lock);
- if (!ret)
- return -EBUSY;
-
- switch (m) {
- case IIO_CHAN_INFO_SCALE:
- ret = -EINVAL;
- if (val == scale_avail[MXS_LRADC_DIV_DISABLED].integer &&
- val2 == scale_avail[MXS_LRADC_DIV_DISABLED].nano) {
- /* divider by two disabled */
- clear_bit(chan->channel, &lradc->is_divided);
- ret = 0;
- } else if (val == scale_avail[MXS_LRADC_DIV_ENABLED].integer &&
- val2 == scale_avail[MXS_LRADC_DIV_ENABLED].nano) {
- /* divider by two enabled */
- set_bit(chan->channel, &lradc->is_divided);
- ret = 0;
- }
-
- break;
- default:
- ret = -EINVAL;
- break;
- }
-
- mutex_unlock(&lradc->lock);
-
- return ret;
-}
-
-static int mxs_lradc_write_raw_get_fmt(struct iio_dev *iio_dev,
- const struct iio_chan_spec *chan,
- long m)
-{
- return IIO_VAL_INT_PLUS_NANO;
-}
-
-static ssize_t mxs_lradc_show_scale_available_ch(struct device *dev,
- struct device_attribute *attr,
- char *buf,
- int ch)
-{
- struct iio_dev *iio = dev_to_iio_dev(dev);
- struct mxs_lradc *lradc = iio_priv(iio);
- int i, len = 0;
-
- for (i = 0; i < ARRAY_SIZE(lradc->scale_avail[ch]); i++)
- len += sprintf(buf + len, "%u.%09u ",
- lradc->scale_avail[ch][i].integer,
- lradc->scale_avail[ch][i].nano);
-
- len += sprintf(buf + len, "\n");
-
- return len;
-}
-
-static ssize_t mxs_lradc_show_scale_available(struct device *dev,
- struct device_attribute *attr,
- char *buf)
-{
- struct iio_dev_attr *iio_attr = to_iio_dev_attr(attr);
-
- return mxs_lradc_show_scale_available_ch(dev, attr, buf,
- iio_attr->address);
-}
-
-#define SHOW_SCALE_AVAILABLE_ATTR(ch) \
-static IIO_DEVICE_ATTR(in_voltage##ch##_scale_available, S_IRUGO, \
- mxs_lradc_show_scale_available, NULL, ch)
-
-SHOW_SCALE_AVAILABLE_ATTR(0);
-SHOW_SCALE_AVAILABLE_ATTR(1);
-SHOW_SCALE_AVAILABLE_ATTR(2);
-SHOW_SCALE_AVAILABLE_ATTR(3);
-SHOW_SCALE_AVAILABLE_ATTR(4);
-SHOW_SCALE_AVAILABLE_ATTR(5);
-SHOW_SCALE_AVAILABLE_ATTR(6);
-SHOW_SCALE_AVAILABLE_ATTR(7);
-SHOW_SCALE_AVAILABLE_ATTR(10);
-SHOW_SCALE_AVAILABLE_ATTR(11);
-SHOW_SCALE_AVAILABLE_ATTR(12);
-SHOW_SCALE_AVAILABLE_ATTR(13);
-SHOW_SCALE_AVAILABLE_ATTR(14);
-SHOW_SCALE_AVAILABLE_ATTR(15);
-
-static struct attribute *mxs_lradc_attributes[] = {
- &iio_dev_attr_in_voltage0_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage1_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage2_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage3_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage4_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage5_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage6_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage7_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage10_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage11_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage12_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage13_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage14_scale_available.dev_attr.attr,
- &iio_dev_attr_in_voltage15_scale_available.dev_attr.attr,
- NULL
-};
-
-static const struct attribute_group mxs_lradc_attribute_group = {
- .attrs = mxs_lradc_attributes,
-};
-
-static const struct iio_info mxs_lradc_iio_info = {
- .driver_module = THIS_MODULE,
- .read_raw = mxs_lradc_read_raw,
- .write_raw = mxs_lradc_write_raw,
- .write_raw_get_fmt = mxs_lradc_write_raw_get_fmt,
- .attrs = &mxs_lradc_attribute_group,
-};
-
-static int mxs_lradc_ts_open(struct input_dev *dev)
-{
- struct mxs_lradc *lradc = input_get_drvdata(dev);
-
- /* Enable the touch-detect circuitry. */
- mxs_lradc_enable_touch_detection(lradc);
-
- return 0;
-}
-
-static void mxs_lradc_disable_ts(struct mxs_lradc *lradc)
-{
- /* stop all interrupts from firing */
- mxs_lradc_reg_clear(lradc, LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
- LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1) |
- LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL2), LRADC_CTRL1);
-
- /* Power-down touchscreen touch-detect circuitry. */
- mxs_lradc_reg_clear(lradc, mxs_lradc_plate_mask(lradc), LRADC_CTRL0);
-}
-
-static void mxs_lradc_ts_close(struct input_dev *dev)
-{
- struct mxs_lradc *lradc = input_get_drvdata(dev);
-
- mxs_lradc_disable_ts(lradc);
-}
-
-static int mxs_lradc_ts_register(struct mxs_lradc *lradc)
-{
- struct input_dev *input;
- struct device *dev = lradc->dev;
-
- if (!lradc->use_touchscreen)
- return 0;
-
- input = devm_input_allocate_device(dev);
- if (!input)
- return -ENOMEM;
-
- input->name = DRIVER_NAME;
- input->id.bustype = BUS_HOST;
- input->open = mxs_lradc_ts_open;
- input->close = mxs_lradc_ts_close;
-
- __set_bit(EV_ABS, input->evbit);
- __set_bit(EV_KEY, input->evbit);
- __set_bit(BTN_TOUCH, input->keybit);
- __set_bit(INPUT_PROP_DIRECT, input->propbit);
- input_set_abs_params(input, ABS_X, 0, LRADC_SINGLE_SAMPLE_MASK, 0, 0);
- input_set_abs_params(input, ABS_Y, 0, LRADC_SINGLE_SAMPLE_MASK, 0, 0);
- input_set_abs_params(input, ABS_PRESSURE, 0, LRADC_SINGLE_SAMPLE_MASK,
- 0, 0);
-
- lradc->ts_input = input;
- input_set_drvdata(input, lradc);
-
- return input_register_device(input);
-}
-
-/*
- * IRQ Handling
- */
-static irqreturn_t mxs_lradc_handle_irq(int irq, void *data)
-{
- struct iio_dev *iio = data;
- struct mxs_lradc *lradc = iio_priv(iio);
- unsigned long reg = readl(lradc->base + LRADC_CTRL1);
- u32 clr_irq = mxs_lradc_irq_mask(lradc);
- const u32 ts_irq_mask =
- LRADC_CTRL1_TOUCH_DETECT_IRQ |
- LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
- LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2);
-
- if (!(reg & mxs_lradc_irq_mask(lradc)))
- return IRQ_NONE;
-
- if (lradc->use_touchscreen && (reg & ts_irq_mask)) {
- mxs_lradc_handle_touch(lradc);
-
- /* Make sure we don't clear the next conversion's interrupt. */
- clr_irq &= ~(LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
- LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2));
- }
-
- if (iio_buffer_enabled(iio)) {
- if (reg & lradc->buffer_vchans)
- iio_trigger_poll(iio->trig);
- } else if (reg & LRADC_CTRL1_LRADC_IRQ(0)) {
- complete(&lradc->completion);
- }
-
- mxs_lradc_reg_clear(lradc, reg & clr_irq, LRADC_CTRL1);
-
- return IRQ_HANDLED;
-}
-
-/*
- * Trigger handling
- */
-static irqreturn_t mxs_lradc_trigger_handler(int irq, void *p)
-{
- struct iio_poll_func *pf = p;
- struct iio_dev *iio = pf->indio_dev;
- struct mxs_lradc *lradc = iio_priv(iio);
- const u32 chan_value = LRADC_CH_ACCUMULATE |
- ((LRADC_DELAY_TIMER_LOOP - 1) << LRADC_CH_NUM_SAMPLES_OFFSET);
- unsigned int i, j = 0;
-
- for_each_set_bit(i, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
- lradc->buffer[j] = readl(lradc->base + LRADC_CH(j));
- mxs_lradc_reg_wrt(lradc, chan_value, LRADC_CH(j));
- lradc->buffer[j] &= LRADC_CH_VALUE_MASK;
- lradc->buffer[j] /= LRADC_DELAY_TIMER_LOOP;
- j++;
- }
-
- iio_push_to_buffers_with_timestamp(iio, lradc->buffer, pf->timestamp);
-
- iio_trigger_notify_done(iio->trig);
-
- return IRQ_HANDLED;
-}
-
-static int mxs_lradc_configure_trigger(struct iio_trigger *trig, bool state)
-{
- struct iio_dev *iio = iio_trigger_get_drvdata(trig);
- struct mxs_lradc *lradc = iio_priv(iio);
- const u32 st = state ? STMP_OFFSET_REG_SET : STMP_OFFSET_REG_CLR;
-
- mxs_lradc_reg_wrt(lradc, LRADC_DELAY_KICK, LRADC_DELAY(0) + st);
-
- return 0;
-}
-
-static const struct iio_trigger_ops mxs_lradc_trigger_ops = {
- .owner = THIS_MODULE,
- .set_trigger_state = &mxs_lradc_configure_trigger,
-};
-
-static int mxs_lradc_trigger_init(struct iio_dev *iio)
-{
- int ret;
- struct iio_trigger *trig;
- struct mxs_lradc *lradc = iio_priv(iio);
-
- trig = iio_trigger_alloc("%s-dev%i", iio->name, iio->id);
- if (!trig)
- return -ENOMEM;
-
- trig->dev.parent = lradc->dev;
- iio_trigger_set_drvdata(trig, iio);
- trig->ops = &mxs_lradc_trigger_ops;
-
- ret = iio_trigger_register(trig);
- if (ret) {
- iio_trigger_free(trig);
- return ret;
- }
-
- lradc->trig = trig;
-
- return 0;
-}
-
-static void mxs_lradc_trigger_remove(struct iio_dev *iio)
-{
- struct mxs_lradc *lradc = iio_priv(iio);
-
- iio_trigger_unregister(lradc->trig);
- iio_trigger_free(lradc->trig);
-}
-
-static int mxs_lradc_buffer_preenable(struct iio_dev *iio)
-{
- struct mxs_lradc *lradc = iio_priv(iio);
- int ret = 0, chan, ofs = 0;
- unsigned long enable = 0;
- u32 ctrl4_set = 0;
- u32 ctrl4_clr = 0;
- u32 ctrl1_irq = 0;
- const u32 chan_value = LRADC_CH_ACCUMULATE |
- ((LRADC_DELAY_TIMER_LOOP - 1) << LRADC_CH_NUM_SAMPLES_OFFSET);
- const int len = bitmap_weight(iio->active_scan_mask,
- LRADC_MAX_TOTAL_CHANS);
-
- if (!len)
- return -EINVAL;
-
- /*
- * Lock the driver so raw access can not be done during buffered
- * operation. This simplifies the code a lot.
- */
- ret = mutex_trylock(&lradc->lock);
- if (!ret)
- return -EBUSY;
-
- lradc->buffer = kmalloc_array(len, sizeof(*lradc->buffer), GFP_KERNEL);
- if (!lradc->buffer) {
- ret = -ENOMEM;
- goto err_mem;
- }
-
- if (lradc->soc == IMX28_LRADC)
- mxs_lradc_reg_clear(
- lradc,
- lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
- LRADC_CTRL1);
- mxs_lradc_reg_clear(lradc, lradc->buffer_vchans, LRADC_CTRL0);
-
- for_each_set_bit(chan, iio->active_scan_mask, LRADC_MAX_TOTAL_CHANS) {
- ctrl4_set |= chan << LRADC_CTRL4_LRADCSELECT_OFFSET(ofs);
- ctrl4_clr |= LRADC_CTRL4_LRADCSELECT_MASK(ofs);
- ctrl1_irq |= LRADC_CTRL1_LRADC_IRQ_EN(ofs);
- mxs_lradc_reg_wrt(lradc, chan_value, LRADC_CH(ofs));
- bitmap_set(&enable, ofs, 1);
- ofs++;
- }
-
- mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK |
- LRADC_DELAY_KICK, LRADC_DELAY(0));
- mxs_lradc_reg_clear(lradc, ctrl4_clr, LRADC_CTRL4);
- mxs_lradc_reg_set(lradc, ctrl4_set, LRADC_CTRL4);
- mxs_lradc_reg_set(lradc, ctrl1_irq, LRADC_CTRL1);
- mxs_lradc_reg_set(lradc, enable << LRADC_DELAY_TRIGGER_LRADCS_OFFSET,
- LRADC_DELAY(0));
-
- return 0;
-
-err_mem:
- mutex_unlock(&lradc->lock);
- return ret;
-}
-
-static int mxs_lradc_buffer_postdisable(struct iio_dev *iio)
-{
- struct mxs_lradc *lradc = iio_priv(iio);
-
- mxs_lradc_reg_clear(lradc, LRADC_DELAY_TRIGGER_LRADCS_MASK |
- LRADC_DELAY_KICK, LRADC_DELAY(0));
-
- mxs_lradc_reg_clear(lradc, lradc->buffer_vchans, LRADC_CTRL0);
- if (lradc->soc == IMX28_LRADC)
- mxs_lradc_reg_clear(
- lradc,
- lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
- LRADC_CTRL1);
-
- kfree(lradc->buffer);
- mutex_unlock(&lradc->lock);
-
- return 0;
-}
-
-static bool mxs_lradc_validate_scan_mask(struct iio_dev *iio,
- const unsigned long *mask)
-{
- struct mxs_lradc *lradc = iio_priv(iio);
- const int map_chans = bitmap_weight(mask, LRADC_MAX_TOTAL_CHANS);
- int rsvd_chans = 0;
- unsigned long rsvd_mask = 0;
-
- if (lradc->use_touchbutton)
- rsvd_mask |= CHAN_MASK_TOUCHBUTTON;
- if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_4WIRE)
- rsvd_mask |= CHAN_MASK_TOUCHSCREEN_4WIRE;
- if (lradc->use_touchscreen == MXS_LRADC_TOUCHSCREEN_5WIRE)
- rsvd_mask |= CHAN_MASK_TOUCHSCREEN_5WIRE;
-
- if (lradc->use_touchbutton)
- rsvd_chans++;
- if (lradc->use_touchscreen)
- rsvd_chans += 2;
-
- /* Test for attempts to map channels with special mode of operation. */
- if (bitmap_intersects(mask, &rsvd_mask, LRADC_MAX_TOTAL_CHANS))
- return false;
-
- /* Test for attempts to map more channels then available slots. */
- if (map_chans + rsvd_chans > LRADC_MAX_MAPPED_CHANS)
- return false;
-
- return true;
-}
-
-static const struct iio_buffer_setup_ops mxs_lradc_buffer_ops = {
- .preenable = &mxs_lradc_buffer_preenable,
- .postenable = &iio_triggered_buffer_postenable,
- .predisable = &iio_triggered_buffer_predisable,
- .postdisable = &mxs_lradc_buffer_postdisable,
- .validate_scan_mask = &mxs_lradc_validate_scan_mask,
-};
-
-/*
- * Driver initialization
- */
-
-#define MXS_ADC_CHAN(idx, chan_type, name) { \
- .type = (chan_type), \
- .indexed = 1, \
- .scan_index = (idx), \
- .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
- BIT(IIO_CHAN_INFO_SCALE), \
- .channel = (idx), \
- .address = (idx), \
- .scan_type = { \
- .sign = 'u', \
- .realbits = LRADC_RESOLUTION, \
- .storagebits = 32, \
- }, \
- .datasheet_name = (name), \
-}
-
-static const struct iio_chan_spec mx23_lradc_chan_spec[] = {
- MXS_ADC_CHAN(0, IIO_VOLTAGE, "LRADC0"),
- MXS_ADC_CHAN(1, IIO_VOLTAGE, "LRADC1"),
- MXS_ADC_CHAN(2, IIO_VOLTAGE, "LRADC2"),
- MXS_ADC_CHAN(3, IIO_VOLTAGE, "LRADC3"),
- MXS_ADC_CHAN(4, IIO_VOLTAGE, "LRADC4"),
- MXS_ADC_CHAN(5, IIO_VOLTAGE, "LRADC5"),
- MXS_ADC_CHAN(6, IIO_VOLTAGE, "VDDIO"),
- MXS_ADC_CHAN(7, IIO_VOLTAGE, "VBATT"),
- /* Combined Temperature sensors */
- {
- .type = IIO_TEMP,
- .indexed = 1,
- .scan_index = 8,
- .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
- BIT(IIO_CHAN_INFO_OFFSET) |
- BIT(IIO_CHAN_INFO_SCALE),
- .channel = 8,
- .scan_type = {.sign = 'u', .realbits = 18, .storagebits = 32,},
- .datasheet_name = "TEMP_DIE",
- },
- /* Hidden channel to keep indexes */
- {
- .type = IIO_TEMP,
- .indexed = 1,
- .scan_index = -1,
- .channel = 9,
- },
- MXS_ADC_CHAN(10, IIO_VOLTAGE, NULL),
- MXS_ADC_CHAN(11, IIO_VOLTAGE, NULL),
- MXS_ADC_CHAN(12, IIO_VOLTAGE, "USB_DP"),
- MXS_ADC_CHAN(13, IIO_VOLTAGE, "USB_DN"),
- MXS_ADC_CHAN(14, IIO_VOLTAGE, "VBG"),
- MXS_ADC_CHAN(15, IIO_VOLTAGE, "VDD5V"),
-};
-
-static const struct iio_chan_spec mx28_lradc_chan_spec[] = {
- MXS_ADC_CHAN(0, IIO_VOLTAGE, "LRADC0"),
- MXS_ADC_CHAN(1, IIO_VOLTAGE, "LRADC1"),
- MXS_ADC_CHAN(2, IIO_VOLTAGE, "LRADC2"),
- MXS_ADC_CHAN(3, IIO_VOLTAGE, "LRADC3"),
- MXS_ADC_CHAN(4, IIO_VOLTAGE, "LRADC4"),
- MXS_ADC_CHAN(5, IIO_VOLTAGE, "LRADC5"),
- MXS_ADC_CHAN(6, IIO_VOLTAGE, "LRADC6"),
- MXS_ADC_CHAN(7, IIO_VOLTAGE, "VBATT"),
- /* Combined Temperature sensors */
- {
- .type = IIO_TEMP,
- .indexed = 1,
- .scan_index = 8,
- .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
- BIT(IIO_CHAN_INFO_OFFSET) |
- BIT(IIO_CHAN_INFO_SCALE),
- .channel = 8,
- .scan_type = {.sign = 'u', .realbits = 18, .storagebits = 32,},
- .datasheet_name = "TEMP_DIE",
- },
- /* Hidden channel to keep indexes */
- {
- .type = IIO_TEMP,
- .indexed = 1,
- .scan_index = -1,
- .channel = 9,
- },
- MXS_ADC_CHAN(10, IIO_VOLTAGE, "VDDIO"),
- MXS_ADC_CHAN(11, IIO_VOLTAGE, "VTH"),
- MXS_ADC_CHAN(12, IIO_VOLTAGE, "VDDA"),
- MXS_ADC_CHAN(13, IIO_VOLTAGE, "VDDD"),
- MXS_ADC_CHAN(14, IIO_VOLTAGE, "VBG"),
- MXS_ADC_CHAN(15, IIO_VOLTAGE, "VDD5V"),
-};
-
-static void mxs_lradc_hw_init(struct mxs_lradc *lradc)
-{
- /* The ADC always uses DELAY CHANNEL 0. */
- const u32 adc_cfg =
- (1 << (LRADC_DELAY_TRIGGER_DELAYS_OFFSET + 0)) |
- (LRADC_DELAY_TIMER_PER << LRADC_DELAY_DELAY_OFFSET);
-
- /* Configure DELAY CHANNEL 0 for generic ADC sampling. */
- mxs_lradc_reg_wrt(lradc, adc_cfg, LRADC_DELAY(0));
-
- /* Disable remaining DELAY CHANNELs */
- mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(1));
- mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(2));
- mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(3));
-
- /* Start internal temperature sensing. */
- mxs_lradc_reg_wrt(lradc, 0, LRADC_CTRL2);
-}
-
-static void mxs_lradc_hw_stop(struct mxs_lradc *lradc)
-{
- int i;
-
- mxs_lradc_reg_clear(lradc,
- lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
- LRADC_CTRL1);
-
- for (i = 0; i < LRADC_MAX_DELAY_CHANS; i++)
- mxs_lradc_reg_wrt(lradc, 0, LRADC_DELAY(i));
-}
-
-static const struct of_device_id mxs_lradc_dt_ids[] = {
- { .compatible = "fsl,imx23-lradc", .data = (void *)IMX23_LRADC, },
- { .compatible = "fsl,imx28-lradc", .data = (void *)IMX28_LRADC, },
- { /* sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, mxs_lradc_dt_ids);
-
-static int mxs_lradc_probe_touchscreen(struct mxs_lradc *lradc,
- struct device_node *lradc_node)
-{
- int ret;
- u32 ts_wires = 0, adapt;
-
- ret = of_property_read_u32(lradc_node, "fsl,lradc-touchscreen-wires",
- &ts_wires);
- if (ret)
- return -ENODEV; /* touchscreen feature disabled */
-
- switch (ts_wires) {
- case 4:
- lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_4WIRE;
- break;
- case 5:
- if (lradc->soc == IMX28_LRADC) {
- lradc->use_touchscreen = MXS_LRADC_TOUCHSCREEN_5WIRE;
- break;
- }
- /* fall through an error message for i.MX23 */
- default:
- dev_err(lradc->dev,
- "Unsupported number of touchscreen wires (%d)\n",
- ts_wires);
- return -EINVAL;
- }
-
- if (of_property_read_u32(lradc_node, "fsl,ave-ctrl", &adapt)) {
- lradc->over_sample_cnt = 4;
- } else {
- if (adapt < 1 || adapt > 32) {
- dev_err(lradc->dev, "Invalid sample count (%u)\n",
- adapt);
- return -EINVAL;
- }
- lradc->over_sample_cnt = adapt;
- }
-
- if (of_property_read_u32(lradc_node, "fsl,ave-delay", &adapt)) {
- lradc->over_sample_delay = 2;
- } else {
- if (adapt < 2 || adapt > LRADC_DELAY_DELAY_MASK + 1) {
- dev_err(lradc->dev, "Invalid sample delay (%u)\n",
- adapt);
- return -EINVAL;
- }
- lradc->over_sample_delay = adapt;
- }
-
- if (of_property_read_u32(lradc_node, "fsl,settling", &adapt)) {
- lradc->settling_delay = 10;
- } else {
- if (adapt < 1 || adapt > LRADC_DELAY_DELAY_MASK) {
- dev_err(lradc->dev, "Invalid settling delay (%u)\n",
- adapt);
- return -EINVAL;
- }
- lradc->settling_delay = adapt;
- }
-
- return 0;
-}
-
-static int mxs_lradc_probe(struct platform_device *pdev)
-{
- const struct of_device_id *of_id =
- of_match_device(mxs_lradc_dt_ids, &pdev->dev);
- const struct mxs_lradc_of_config *of_cfg =
- &mxs_lradc_of_config[(enum mxs_lradc_id)of_id->data];
- struct device *dev = &pdev->dev;
- struct device_node *node = dev->of_node;
- struct mxs_lradc *lradc;
- struct iio_dev *iio;
- struct resource *iores;
- int ret = 0, touch_ret;
- int i, s;
- u64 scale_uv;
-
- /* Allocate the IIO device. */
- iio = devm_iio_device_alloc(dev, sizeof(*lradc));
- if (!iio) {
- dev_err(dev, "Failed to allocate IIO device\n");
- return -ENOMEM;
- }
-
- lradc = iio_priv(iio);
- lradc->soc = (enum mxs_lradc_id)of_id->data;
-
- /* Grab the memory area */
- iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- lradc->dev = &pdev->dev;
- lradc->base = devm_ioremap_resource(dev, iores);
- if (IS_ERR(lradc->base))
- return PTR_ERR(lradc->base);
-
- lradc->clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(lradc->clk)) {
- dev_err(dev, "Failed to get the delay unit clock\n");
- return PTR_ERR(lradc->clk);
- }
- ret = clk_prepare_enable(lradc->clk);
- if (ret != 0) {
- dev_err(dev, "Failed to enable the delay unit clock\n");
- return ret;
- }
-
- touch_ret = mxs_lradc_probe_touchscreen(lradc, node);
-
- if (touch_ret == 0)
- lradc->buffer_vchans = BUFFER_VCHANS_LIMITED;
- else
- lradc->buffer_vchans = BUFFER_VCHANS_ALL;
-
- /* Grab all IRQ sources */
- for (i = 0; i < of_cfg->irq_count; i++) {
- lradc->irq[i] = platform_get_irq(pdev, i);
- if (lradc->irq[i] < 0) {
- ret = lradc->irq[i];
- goto err_clk;
- }
-
- ret = devm_request_irq(dev, lradc->irq[i],
- mxs_lradc_handle_irq, 0,
- of_cfg->irq_name[i], iio);
- if (ret)
- goto err_clk;
- }
-
- lradc->vref_mv = of_cfg->vref_mv;
-
- platform_set_drvdata(pdev, iio);
-
- init_completion(&lradc->completion);
- mutex_init(&lradc->lock);
-
- iio->name = pdev->name;
- iio->dev.parent = &pdev->dev;
- iio->info = &mxs_lradc_iio_info;
- iio->modes = INDIO_DIRECT_MODE;
- iio->masklength = LRADC_MAX_TOTAL_CHANS;
-
- if (lradc->soc == IMX23_LRADC) {
- iio->channels = mx23_lradc_chan_spec;
- iio->num_channels = ARRAY_SIZE(mx23_lradc_chan_spec);
- } else {
- iio->channels = mx28_lradc_chan_spec;
- iio->num_channels = ARRAY_SIZE(mx28_lradc_chan_spec);
- }
-
- ret = iio_triggered_buffer_setup(iio, &iio_pollfunc_store_time,
- &mxs_lradc_trigger_handler,
- &mxs_lradc_buffer_ops);
- if (ret)
- goto err_clk;
-
- ret = mxs_lradc_trigger_init(iio);
- if (ret)
- goto err_trig;
-
- /* Populate available ADC input ranges */
- for (i = 0; i < LRADC_MAX_TOTAL_CHANS; i++) {
- for (s = 0; s < ARRAY_SIZE(lradc->scale_avail[i]); s++) {
- /*
- * [s=0] = optional divider by two disabled (default)
- * [s=1] = optional divider by two enabled
- *
- * The scale is calculated by doing:
- * Vref >> (realbits - s)
- * which multiplies by two on the second component
- * of the array.
- */
- scale_uv = ((u64)lradc->vref_mv[i] * 100000000) >>
- (LRADC_RESOLUTION - s);
- lradc->scale_avail[i][s].nano =
- do_div(scale_uv, 100000000) * 10;
- lradc->scale_avail[i][s].integer = scale_uv;
- }
- }
-
- ret = stmp_reset_block(lradc->base);
- if (ret)
- goto err_dev;
-
- /* Configure the hardware. */
- mxs_lradc_hw_init(lradc);
-
- /* Register the touchscreen input device. */
- if (touch_ret == 0) {
- ret = mxs_lradc_ts_register(lradc);
- if (ret)
- goto err_ts_register;
- }
-
- /* Register IIO device. */
- ret = iio_device_register(iio);
- if (ret) {
- dev_err(dev, "Failed to register IIO device\n");
- return ret;
- }
-
- return 0;
-
-err_ts_register:
- mxs_lradc_hw_stop(lradc);
-err_dev:
- mxs_lradc_trigger_remove(iio);
-err_trig:
- iio_triggered_buffer_cleanup(iio);
-err_clk:
- clk_disable_unprepare(lradc->clk);
- return ret;
-}
-
-static int mxs_lradc_remove(struct platform_device *pdev)
-{
- struct iio_dev *iio = platform_get_drvdata(pdev);
- struct mxs_lradc *lradc = iio_priv(iio);
-
- iio_device_unregister(iio);
- mxs_lradc_hw_stop(lradc);
- mxs_lradc_trigger_remove(iio);
- iio_triggered_buffer_cleanup(iio);
-
- clk_disable_unprepare(lradc->clk);
-
- return 0;
-}
-
-static struct platform_driver mxs_lradc_driver = {
- .driver = {
- .name = DRIVER_NAME,
- .of_match_table = mxs_lradc_dt_ids,
- },
- .probe = mxs_lradc_probe,
- .remove = mxs_lradc_remove,
-};
-
-module_platform_driver(mxs_lradc_driver);
-
-MODULE_AUTHOR("Marek Vasut <marex@denx.de>");
-MODULE_DESCRIPTION("Freescale MXS LRADC driver");
-MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:" DRIVER_NAME);
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 0335997..52458cf 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -829,6 +829,16 @@
To compile this driver as a module, choose M here: the
module will be called usbtouchscreen.
+config TOUCHSCREEN_MXS_LRADC
+ tristate "Freescale i.MX23/i.MX28 LRADC touchscreen"
+ depends on MFD_MXS_LRADC
+ help
+ Say Y here if you have a touchscreen connected to the low-resolution
+ analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor.
+
+ To compile this driver as a module, choose M here: the module will be
+ called mxs-lradc-ts.
+
config TOUCHSCREEN_MX25
tristate "Freescale i.MX25 touchscreen input driver"
depends on MFD_MX25_TSADC
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index b622e53..96761ce 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -45,6 +45,7 @@
obj-$(CONFIG_TOUCHSCREEN_IPROC) += bcm_iproc_tsc.o
obj-$(CONFIG_TOUCHSCREEN_LPC32XX) += lpc32xx_ts.o
obj-$(CONFIG_TOUCHSCREEN_MAX11801) += max11801_ts.o
+obj-$(CONFIG_TOUCHSCREEN_MXS_LRADC) += mxs-lradc-ts.o
obj-$(CONFIG_TOUCHSCREEN_MX25) += fsl-imx25-tcq.o
obj-$(CONFIG_TOUCHSCREEN_MC13783) += mc13783_ts.o
obj-$(CONFIG_TOUCHSCREEN_MCS5000) += mcs5000_ts.o
diff --git a/drivers/input/touchscreen/mxs-lradc-ts.c b/drivers/input/touchscreen/mxs-lradc-ts.c
new file mode 100644
index 0000000..4b4aebf
--- /dev/null
+++ b/drivers/input/touchscreen/mxs-lradc-ts.c
@@ -0,0 +1,714 @@
+/*
+ * Freescale MXS LRADC touchscreen driver
+ *
+ * Copyright (c) 2012 DENX Software Engineering, GmbH.
+ * Copyright (c) 2017 Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
+ *
+ * Authors:
+ * Marek Vasut <marex@denx.de>
+ * Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/mxs-lradc.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+
+const char *mxs_lradc_ts_irq_names[] = {
+ "mxs-lradc-touchscreen",
+ "mxs-lradc-channel6",
+ "mxs-lradc-channel7",
+};
+
+/*
+ * Touchscreen handling
+ */
+enum mxs_lradc_ts_plate {
+ LRADC_TOUCH = 0,
+ LRADC_SAMPLE_X,
+ LRADC_SAMPLE_Y,
+ LRADC_SAMPLE_PRESSURE,
+ LRADC_SAMPLE_VALID,
+};
+
+struct mxs_lradc_ts {
+ struct mxs_lradc *lradc;
+ struct device *dev;
+
+ void __iomem *base;
+ /*
+ * When the touchscreen is enabled, we give it two private virtual
+ * channels: #6 and #7. This means that only 6 virtual channels (instead
+ * of 8) will be available for buffered capture.
+ */
+#define TOUCHSCREEN_VCHANNEL1 7
+#define TOUCHSCREEN_VCHANNEL2 6
+
+ struct input_dev *ts_input;
+
+ enum mxs_lradc_ts_plate cur_plate; /* state machine */
+ bool ts_valid;
+ unsigned int ts_x_pos;
+ unsigned int ts_y_pos;
+ unsigned int ts_pressure;
+
+ /* handle touchscreen's physical behaviour */
+ /* samples per coordinate */
+ unsigned int over_sample_cnt;
+ /* time clocks between samples */
+ unsigned int over_sample_delay;
+ /* time in clocks to wait after the plates where switched */
+ unsigned int settling_delay;
+ spinlock_t lock;
+};
+
+struct state_info {
+ u32 mask;
+ u32 bit;
+ u32 x_plate;
+ u32 y_plate;
+ u32 pressure;
+};
+
+static struct state_info info[] = {
+ {LRADC_CTRL0_MX23_PLATE_MASK, LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE,
+ LRADC_CTRL0_MX23_XP | LRADC_CTRL0_MX23_XM,
+ LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_YM,
+ LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XM},
+ {LRADC_CTRL0_MX28_PLATE_MASK, LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE,
+ LRADC_CTRL0_MX28_XPPSW | LRADC_CTRL0_MX28_XNNSW,
+ LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_YNNSW,
+ LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW}
+};
+
+static bool mxs_lradc_check_touch_event(struct mxs_lradc_ts *ts)
+{
+ return !!(readl(ts->base + LRADC_STATUS) &
+ LRADC_STATUS_TOUCH_DETECT_RAW);
+}
+
+static void mxs_lradc_map_ts_channel(struct mxs_lradc_ts *ts, unsigned int vch,
+ unsigned int ch)
+{
+ writel(LRADC_CTRL4_LRADCSELECT_MASK(vch),
+ ts->base + LRADC_CTRL4 + STMP_OFFSET_REG_CLR);
+ writel(LRADC_CTRL4_LRADCSELECT(vch, ch),
+ ts->base + LRADC_CTRL4 + STMP_OFFSET_REG_SET);
+}
+
+static void mxs_lradc_setup_ts_channel(struct mxs_lradc_ts *ts, unsigned int ch)
+{
+ /*
+ * prepare for oversampling conversion
+ *
+ * from the datasheet:
+ * "The ACCUMULATE bit in the appropriate channel register
+ * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
+ * otherwise, the IRQs will not fire."
+ */
+ writel(LRADC_CH_ACCUMULATE |
+ LRADC_CH_NUM_SAMPLES(ts->over_sample_cnt - 1),
+ ts->base + LRADC_CH(ch));
+
+ /* from the datasheet:
+ * "Software must clear this register in preparation for a
+ * multi-cycle accumulation.
+ */
+ writel(LRADC_CH_VALUE_MASK,
+ ts->base + LRADC_CH(ch) + STMP_OFFSET_REG_CLR);
+
+ /*
+ * prepare the delay/loop unit according to the oversampling count
+ *
+ * from the datasheet:
+ * "The DELAY fields in HW_LRADC_DELAY0, HW_LRADC_DELAY1,
+ * HW_LRADC_DELAY2, and HW_LRADC_DELAY3 must be non-zero; otherwise,
+ * the LRADC will not trigger the delay group."
+ */
+ writel(LRADC_DELAY_TRIGGER(1 << ch) | LRADC_DELAY_TRIGGER_DELAYS(0) |
+ LRADC_DELAY_LOOP(ts->over_sample_cnt - 1) |
+ LRADC_DELAY_DELAY(ts->over_sample_delay - 1),
+ ts->base + LRADC_DELAY(3));
+
+ writel(LRADC_CTRL1_LRADC_IRQ(ch),
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+
+ /*
+ * after changing the touchscreen plates setting
+ * the signals need some initial time to settle. Start the
+ * SoC's delay unit and start the conversion later
+ * and automatically.
+ */
+ writel(LRADC_DELAY_TRIGGER(0) | LRADC_DELAY_TRIGGER_DELAYS(BIT(3)) |
+ LRADC_DELAY_KICK | LRADC_DELAY_DELAY(ts->settling_delay),
+ ts->base + LRADC_DELAY(2));
+}
+
+/*
+ * Pressure detection is special:
+ * We want to do both required measurements for the pressure detection in
+ * one turn. Use the hardware features to chain both conversions and let the
+ * hardware report one interrupt if both conversions are done
+ */
+static void mxs_lradc_setup_ts_pressure(struct mxs_lradc_ts *ts,
+ unsigned int ch1, unsigned int ch2)
+{
+ u32 reg;
+
+ /*
+ * prepare for oversampling conversion
+ *
+ * from the datasheet:
+ * "The ACCUMULATE bit in the appropriate channel register
+ * HW_LRADC_CHn must be set to 1 if NUM_SAMPLES is greater then 0;
+ * otherwise, the IRQs will not fire."
+ */
+ reg = LRADC_CH_ACCUMULATE |
+ LRADC_CH_NUM_SAMPLES(ts->over_sample_cnt - 1);
+ writel(reg, ts->base + LRADC_CH(ch1));
+ writel(reg, ts->base + LRADC_CH(ch2));
+
+ /* from the datasheet:
+ * "Software must clear this register in preparation for a
+ * multi-cycle accumulation.
+ */
+ writel(LRADC_CH_VALUE_MASK,
+ ts->base + LRADC_CH(ch1) + STMP_OFFSET_REG_CLR);
+ writel(LRADC_CH_VALUE_MASK,
+ ts->base + LRADC_CH(ch2) + STMP_OFFSET_REG_CLR);
+
+ /* prepare the delay/loop unit according to the oversampling count */
+ writel(LRADC_DELAY_TRIGGER(1 << ch1) | LRADC_DELAY_TRIGGER(1 << ch2) |
+ LRADC_DELAY_TRIGGER_DELAYS(0) |
+ LRADC_DELAY_LOOP(ts->over_sample_cnt - 1) |
+ LRADC_DELAY_DELAY(ts->over_sample_delay - 1),
+ ts->base + LRADC_DELAY(3));
+
+ writel(LRADC_CTRL1_LRADC_IRQ(ch2),
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+
+ /*
+ * after changing the touchscreen plates setting
+ * the signals need some initial time to settle. Start the
+ * SoC's delay unit and start the conversion later
+ * and automatically.
+ */
+ writel(LRADC_DELAY_TRIGGER(0) | LRADC_DELAY_TRIGGER_DELAYS(BIT(3)) |
+ LRADC_DELAY_KICK | LRADC_DELAY_DELAY(ts->settling_delay),
+ ts->base + LRADC_DELAY(2));
+}
+
+static unsigned int mxs_lradc_ts_read_raw_channel(struct mxs_lradc_ts *ts,
+ unsigned int channel)
+{
+ u32 reg;
+ unsigned int num_samples, val;
+
+ reg = readl(ts->base + LRADC_CH(channel));
+ if (reg & LRADC_CH_ACCUMULATE)
+ num_samples = ts->over_sample_cnt;
+ else
+ num_samples = 1;
+
+ val = (reg & LRADC_CH_VALUE_MASK) >> LRADC_CH_VALUE_OFFSET;
+ return val / num_samples;
+}
+
+static unsigned int mxs_lradc_read_ts_pressure(struct mxs_lradc_ts *ts,
+ unsigned int ch1, unsigned int ch2)
+{
+ u32 reg, mask;
+ unsigned int pressure, m1, m2;
+
+ mask = LRADC_CTRL1_LRADC_IRQ(ch1) | LRADC_CTRL1_LRADC_IRQ(ch2);
+ reg = readl(ts->base + LRADC_CTRL1) & mask;
+
+ while (reg != mask) {
+ reg = readl(ts->base + LRADC_CTRL1) & mask;
+ dev_dbg(ts->dev, "One channel is still busy: %X\n", reg);
+ }
+
+ m1 = mxs_lradc_ts_read_raw_channel(ts, ch1);
+ m2 = mxs_lradc_ts_read_raw_channel(ts, ch2);
+
+ if (m2 == 0) {
+ dev_warn(ts->dev, "Cannot calculate pressure\n");
+ return 1 << (LRADC_RESOLUTION - 1);
+ }
+
+ /* simply scale the value from 0 ... max ADC resolution */
+ pressure = m1;
+ pressure *= (1 << LRADC_RESOLUTION);
+ pressure /= m2;
+
+ dev_dbg(ts->dev, "Pressure = %u\n", pressure);
+ return pressure;
+}
+
+#define TS_CH_XP 2
+#define TS_CH_YP 3
+#define TS_CH_XM 4
+#define TS_CH_YM 5
+
+/*
+ * YP(open)--+-------------+
+ * | |--+
+ * | | |
+ * YM(-)--+-------------+ |
+ * +--------------+
+ * | |
+ * XP(weak+) XM(open)
+ *
+ * "weak+" means 200k Ohm VDDIO
+ * (-) means GND
+ */
+static void mxs_lradc_setup_touch_detection(struct mxs_lradc_ts *ts)
+{
+ struct mxs_lradc *lradc = ts->lradc;
+
+ /*
+ * In order to detect a touch event the 'touch detect enable' bit
+ * enables:
+ * - a weak pullup to the X+ connector
+ * - a strong ground at the Y- connector
+ */
+ writel(info[lradc->soc].mask,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+ writel(info[lradc->soc].bit,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+}
+
+/*
+ * YP(meas)--+-------------+
+ * | |--+
+ * | | |
+ * YM(open)--+-------------+ |
+ * +--------------+
+ * | |
+ * XP(+) XM(-)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_x_pos(struct mxs_lradc_ts *ts)
+{
+ struct mxs_lradc *lradc = ts->lradc;
+
+ writel(info[lradc->soc].mask,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+ writel(info[lradc->soc].x_plate,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+
+ ts->cur_plate = LRADC_SAMPLE_X;
+ mxs_lradc_map_ts_channel(ts, TOUCHSCREEN_VCHANNEL1, TS_CH_YP);
+ mxs_lradc_setup_ts_channel(ts, TOUCHSCREEN_VCHANNEL1);
+}
+
+/*
+ * YP(+)--+-------------+
+ * | |--+
+ * | | |
+ * YM(-)--+-------------+ |
+ * +--------------+
+ * | |
+ * XP(open) XM(meas)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_y_pos(struct mxs_lradc_ts *ts)
+{
+ struct mxs_lradc *lradc = ts->lradc;
+
+ writel(info[lradc->soc].mask,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+ writel(info[lradc->soc].y_plate,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+
+ ts->cur_plate = LRADC_SAMPLE_Y;
+ mxs_lradc_map_ts_channel(ts, TOUCHSCREEN_VCHANNEL1, TS_CH_XM);
+ mxs_lradc_setup_ts_channel(ts, TOUCHSCREEN_VCHANNEL1);
+}
+
+/*
+ * YP(+)--+-------------+
+ * | |--+
+ * | | |
+ * YM(meas)--+-------------+ |
+ * +--------------+
+ * | |
+ * XP(meas) XM(-)
+ *
+ * (+) means here 1.85 V
+ * (-) means here GND
+ */
+static void mxs_lradc_prepare_pressure(struct mxs_lradc_ts *ts)
+{
+ struct mxs_lradc *lradc = ts->lradc;
+
+ writel(info[lradc->soc].mask,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+ writel(info[lradc->soc].pressure,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+
+ ts->cur_plate = LRADC_SAMPLE_PRESSURE;
+ mxs_lradc_map_ts_channel(ts, TOUCHSCREEN_VCHANNEL1, TS_CH_YM);
+ mxs_lradc_map_ts_channel(ts, TOUCHSCREEN_VCHANNEL2, TS_CH_XP);
+ mxs_lradc_setup_ts_pressure(ts, TOUCHSCREEN_VCHANNEL2,
+ TOUCHSCREEN_VCHANNEL1);
+}
+
+static void mxs_lradc_enable_touch_detection(struct mxs_lradc_ts *ts)
+{
+ mxs_lradc_setup_touch_detection(ts);
+
+ ts->cur_plate = LRADC_TOUCH;
+ writel(LRADC_CTRL1_TOUCH_DETECT_IRQ | LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+ writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+}
+
+static void mxs_lradc_start_touch_event(struct mxs_lradc_ts *ts)
+{
+ writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+ writel(LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1),
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+ /*
+ * start with the Y-pos, because it uses nearly the same plate
+ * settings like the touch detection
+ */
+ mxs_lradc_prepare_y_pos(ts);
+}
+
+static void mxs_lradc_report_ts_event(struct mxs_lradc_ts *ts)
+{
+ input_report_abs(ts->ts_input, ABS_X, ts->ts_x_pos);
+ input_report_abs(ts->ts_input, ABS_Y, ts->ts_y_pos);
+ input_report_abs(ts->ts_input, ABS_PRESSURE, ts->ts_pressure);
+ input_report_key(ts->ts_input, BTN_TOUCH, 1);
+ input_sync(ts->ts_input);
+}
+
+static void mxs_lradc_complete_touch_event(struct mxs_lradc_ts *ts)
+{
+ mxs_lradc_setup_touch_detection(ts);
+ ts->cur_plate = LRADC_SAMPLE_VALID;
+ /*
+ * start a dummy conversion to burn time to settle the signals
+ * note: we are not interested in the conversion's value
+ */
+ writel(0, ts->base + LRADC_CH(TOUCHSCREEN_VCHANNEL1));
+ writel(LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
+ LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2),
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+ writel(LRADC_DELAY_TRIGGER(1 << TOUCHSCREEN_VCHANNEL1) |
+ LRADC_DELAY_KICK | LRADC_DELAY_DELAY(10),
+ ts->base + LRADC_DELAY(2));
+}
+
+/*
+ * in order to avoid false measurements, report only samples where
+ * the surface is still touched after the position measurement
+ */
+static void mxs_lradc_finish_touch_event(struct mxs_lradc_ts *ts, bool valid)
+{
+ /* if it is still touched, report the sample */
+ if (valid && mxs_lradc_check_touch_event(ts)) {
+ ts->ts_valid = true;
+ mxs_lradc_report_ts_event(ts);
+ }
+
+ /* if it is even still touched, continue with the next measurement */
+ if (mxs_lradc_check_touch_event(ts)) {
+ mxs_lradc_prepare_y_pos(ts);
+ return;
+ }
+
+ if (ts->ts_valid) {
+ /* signal the release */
+ ts->ts_valid = false;
+ input_report_key(ts->ts_input, BTN_TOUCH, 0);
+ input_sync(ts->ts_input);
+ }
+
+ /* if it is released, wait for the next touch via IRQ */
+ ts->cur_plate = LRADC_TOUCH;
+ writel(0, ts->base + LRADC_DELAY(2));
+ writel(0, ts->base + LRADC_DELAY(3));
+ writel(LRADC_CTRL1_TOUCH_DETECT_IRQ |
+ LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1) |
+ LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1),
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+ writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN,
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_SET);
+}
+
+/* touchscreen's state machine */
+static void mxs_lradc_handle_touch(struct mxs_lradc_ts *ts)
+{
+ switch (ts->cur_plate) {
+ case LRADC_TOUCH:
+ if (mxs_lradc_check_touch_event(ts))
+ mxs_lradc_start_touch_event(ts);
+ writel(LRADC_CTRL1_TOUCH_DETECT_IRQ,
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+ return;
+
+ case LRADC_SAMPLE_Y:
+ ts->ts_y_pos =
+ mxs_lradc_ts_read_raw_channel(ts, TOUCHSCREEN_VCHANNEL1);
+ mxs_lradc_prepare_x_pos(ts);
+ return;
+
+ case LRADC_SAMPLE_X:
+ ts->ts_x_pos =
+ mxs_lradc_ts_read_raw_channel(ts, TOUCHSCREEN_VCHANNEL1);
+ mxs_lradc_prepare_pressure(ts);
+ return;
+
+ case LRADC_SAMPLE_PRESSURE:
+ ts->ts_pressure =
+ mxs_lradc_read_ts_pressure(ts,
+ TOUCHSCREEN_VCHANNEL2,
+ TOUCHSCREEN_VCHANNEL1);
+ mxs_lradc_complete_touch_event(ts);
+ return;
+
+ case LRADC_SAMPLE_VALID:
+ mxs_lradc_finish_touch_event(ts, 1);
+ break;
+ }
+}
+
+/* IRQ Handling */
+static irqreturn_t mxs_lradc_ts_handle_irq(int irq, void *data)
+{
+ struct mxs_lradc_ts *ts = data;
+ struct mxs_lradc *lradc = ts->lradc;
+ unsigned long reg = readl(ts->base + LRADC_CTRL1);
+ u32 clr_irq = mxs_lradc_irq_mask(lradc);
+ const u32 ts_irq_mask =
+ LRADC_CTRL1_TOUCH_DETECT_IRQ |
+ LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
+ LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2);
+ unsigned long flags;
+
+ if (!(reg & mxs_lradc_irq_mask(lradc)))
+ return IRQ_NONE;
+
+ if (reg & ts_irq_mask) {
+ spin_lock_irqsave(&ts->lock, flags);
+ mxs_lradc_handle_touch(ts);
+ spin_unlock_irqrestore(&ts->lock, flags);
+ /* Make sure we don't clear the next conversion's interrupt. */
+ clr_irq &= ~(LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL1) |
+ LRADC_CTRL1_LRADC_IRQ(TOUCHSCREEN_VCHANNEL2));
+ writel(reg & clr_irq,
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int mxs_lradc_ts_open(struct input_dev *dev)
+{
+ struct mxs_lradc_ts *ts = input_get_drvdata(dev);
+
+ /* Enable the touch-detect circuitry. */
+ mxs_lradc_enable_touch_detection(ts);
+
+ return 0;
+}
+
+static void mxs_lradc_ts_stop(struct mxs_lradc_ts *ts)
+{
+ int i;
+ struct mxs_lradc *lradc = ts->lradc;
+
+ /* stop all interrupts from firing */
+ writel(LRADC_CTRL1_TOUCH_DETECT_IRQ_EN |
+ LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL1) |
+ LRADC_CTRL1_LRADC_IRQ_EN(TOUCHSCREEN_VCHANNEL2),
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+
+ /* Power-down touchscreen touch-detect circuitry. */
+ writel(info[lradc->soc].mask,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+
+ writel(lradc->buffer_vchans << LRADC_CTRL1_LRADC_IRQ_EN_OFFSET,
+ ts->base + LRADC_CTRL1 + STMP_OFFSET_REG_CLR);
+
+ for (i = 1; i < LRADC_MAX_DELAY_CHANS; i++)
+ writel(0, ts->base + LRADC_DELAY(i));
+}
+
+static void mxs_lradc_ts_close(struct input_dev *dev)
+{
+ struct mxs_lradc_ts *ts = input_get_drvdata(dev);
+
+ mxs_lradc_ts_stop(ts);
+}
+
+static void mxs_lradc_ts_hw_init(struct mxs_lradc_ts *ts)
+{
+ struct mxs_lradc *lradc = ts->lradc;
+
+ /* Configure the touchscreen type */
+ if (lradc->soc == IMX28_LRADC) {
+ writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_CLR);
+
+ if (lradc->touchscreen_wire == MXS_LRADC_TOUCHSCREEN_5WIRE)
+ writel(LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE,
+ ts->base + LRADC_CTRL0 + STMP_OFFSET_REG_SET);
+ }
+}
+
+static int mxs_lradc_ts_register(struct mxs_lradc_ts *ts)
+{
+ struct input_dev *input = ts->ts_input;
+ struct device *dev = ts->dev;
+
+ input = devm_input_allocate_device(dev);
+ if (!input)
+ return -ENOMEM;
+
+ input->name = "mxs-lradc-ts";
+ input->id.bustype = BUS_HOST;
+ input->open = mxs_lradc_ts_open;
+ input->close = mxs_lradc_ts_close;
+
+ __set_bit(INPUT_PROP_DIRECT, input->propbit);
+ input_set_capability(input, EV_KEY, BTN_TOUCH);
+ input_set_abs_params(input, ABS_X, 0, LRADC_SINGLE_SAMPLE_MASK, 0, 0);
+ input_set_abs_params(input, ABS_Y, 0, LRADC_SINGLE_SAMPLE_MASK, 0, 0);
+ input_set_abs_params(input, ABS_PRESSURE, 0, LRADC_SINGLE_SAMPLE_MASK,
+ 0, 0);
+
+ ts->ts_input = input;
+ input_set_drvdata(input, ts);
+
+ return input_register_device(input);
+}
+
+static int mxs_lradc_ts_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *node = dev->parent->of_node;
+ struct mxs_lradc *lradc = dev_get_drvdata(dev->parent);
+ struct mxs_lradc_ts *ts;
+ struct resource *iores;
+ int ret, irq, virq, i;
+ u32 ts_wires = 0, adapt;
+
+ ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
+ if (!ts)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, ts);
+
+ ts->lradc = lradc;
+ ts->dev = dev;
+ spin_lock_init(&ts->lock);
+
+ iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ts->base = devm_ioremap(dev, iores->start, resource_size(iores));
+ if (IS_ERR(ts->base))
+ return PTR_ERR(ts->base);
+
+ ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
+ &ts_wires);
+ if (ret)
+ return ret;
+
+ if (of_property_read_u32(node, "fsl,ave-ctrl", &adapt)) {
+ ts->over_sample_cnt = 4;
+ } else {
+ if (adapt >= 1 || adapt <= 32) {
+ ts->over_sample_cnt = adapt;
+ } else {
+ dev_err(ts->dev, "Invalid sample count (%u)\n",
+ adapt);
+ return -EINVAL;
+ }
+ }
+
+ if (of_property_read_u32(node, "fsl,ave-delay", &adapt)) {
+ ts->over_sample_delay = 2;
+ } else {
+ if (adapt >= 2 || adapt <= LRADC_DELAY_DELAY_MASK + 1) {
+ ts->over_sample_delay = adapt;
+ } else {
+ dev_err(ts->dev, "Invalid sample delay (%u)\n",
+ adapt);
+ return -EINVAL;
+ }
+ }
+
+ if (of_property_read_u32(node, "fsl,settling", &adapt)) {
+ ts->settling_delay = 10;
+ } else {
+ if (adapt >= 1 || adapt <= LRADC_DELAY_DELAY_MASK) {
+ ts->settling_delay = adapt;
+ } else {
+ dev_err(ts->dev, "Invalid settling delay (%u)\n",
+ adapt);
+ return -EINVAL;
+ }
+ }
+
+ ret = stmp_reset_block(ts->base);
+ if (ret)
+ return ret;
+
+ mxs_lradc_ts_hw_init(ts);
+
+ for (i = 0; i < 3; i++) {
+ irq = platform_get_irq_byname(pdev, mxs_lradc_ts_irq_names[i]);
+ if (irq < 0)
+ return irq;
+
+ virq = irq_of_parse_and_map(node, irq);
+
+ mxs_lradc_ts_stop(ts);
+
+ ret = devm_request_irq(dev, virq,
+ mxs_lradc_ts_handle_irq,
+ 0, mxs_lradc_ts_irq_names[i], ts);
+ if (ret)
+ return ret;
+ }
+
+ return mxs_lradc_ts_register(ts);
+}
+
+static struct platform_driver mxs_lradc_ts_driver = {
+ .driver = {
+ .name = "mxs-lradc-ts",
+ },
+ .probe = mxs_lradc_ts_probe,
+};
+module_platform_driver(mxs_lradc_ts_driver);
+
+MODULE_AUTHOR("Marek Vasut <marex@denx.de>");
+MODULE_DESCRIPTION("Freescale MXS LRADC touchscreen driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:mxs-lradc-ts");
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 55ecdfb..8bbc91b 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -344,6 +344,23 @@
help
Select this if your MC13xxx is connected via an I2C bus.
+config MFD_MXS_LRADC
+ tristate "Freescale i.MX23/i.MX28 LRADC"
+ depends on ARCH_MXS || COMPILE_TEST
+ select MFD_CORE
+ select STMP_DEVICE
+ help
+ Say yes here to build support for the Low Resolution
+ Analog-to-Digital Converter (LRADC) found on the i.MX23 and i.MX28
+ processors. This driver provides common support for accessing the
+ device, additional drivers must be enabled in order to use the
+ functionality of the device:
+ mxs-lradc-adc for ADC readings
+ mxs-lradc-ts for touchscreen support
+
+ This driver can also be built as a module. If so, the module will be
+ called mxs-lradc.
+
config MFD_MX25_TSADC
tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
select REGMAP_MMIO
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 31ce076..790698a 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -215,3 +215,4 @@
obj-$(CONFIG_MFD_SUN4I_GPADC) += sun4i-gpadc.o
obj-$(CONFIG_MFD_STM32_TIMERS) += stm32-timers.o
+obj-$(CONFIG_MFD_MXS_LRADC) += mxs-lradc.o
diff --git a/drivers/mfd/exynos-lpass.c b/drivers/mfd/exynos-lpass.c
index 2e064fb..8bebad9 100644
--- a/drivers/mfd/exynos-lpass.c
+++ b/drivers/mfd/exynos-lpass.c
@@ -18,11 +18,11 @@
#include <linux/io.h>
#include <linux/module.h>
#include <linux/mfd/syscon.h>
-#include <linux/mfd/syscon/exynos5-pmu.h>
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
+#include <linux/soc/samsung/exynos-regs-pmu.h>
#include <linux/types.h>
/* LPASS Top register definitions */
@@ -83,7 +83,7 @@ static void exynos_lpass_enable(struct exynos_lpass *lpass)
/* Activate related PADs from retention state */
regmap_write(lpass->pmu, EXYNOS5433_PAD_RETENTION_AUD_OPTION,
- EXYNOS5433_PAD_INITIATE_WAKEUP_FROM_LOWPWR);
+ EXYNOS_WAKEUP_FROM_LOWPWR);
exynos_lpass_core_sw_reset(lpass, LPASS_I2S_SW_RESET);
exynos_lpass_core_sw_reset(lpass, LPASS_DMA_SW_RESET);
diff --git a/drivers/mfd/mxs-lradc.c b/drivers/mfd/mxs-lradc.c
new file mode 100644
index 0000000..630bd19
--- /dev/null
+++ b/drivers/mfd/mxs-lradc.c
@@ -0,0 +1,267 @@
+/*
+ * Freescale MXS Low Resolution Analog-to-Digital Converter driver
+ *
+ * Copyright (c) 2012 DENX Software Engineering, GmbH.
+ * Copyright (c) 2017 Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
+ *
+ * Authors:
+ * Marek Vasut <marex@denx.de>
+ * Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/mxs-lradc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define ADC_CELL 0
+#define TSC_CELL 1
+#define RES_MEM 0
+
+enum mx23_lradc_irqs {
+ MX23_LRADC_TS_IRQ = 0,
+ MX23_LRADC_CH0_IRQ,
+ MX23_LRADC_CH1_IRQ,
+ MX23_LRADC_CH2_IRQ,
+ MX23_LRADC_CH3_IRQ,
+ MX23_LRADC_CH4_IRQ,
+ MX23_LRADC_CH5_IRQ,
+ MX23_LRADC_CH6_IRQ,
+ MX23_LRADC_CH7_IRQ,
+};
+
+enum mx28_lradc_irqs {
+ MX28_LRADC_TS_IRQ = 0,
+ MX28_LRADC_TRESH0_IRQ,
+ MX28_LRADC_TRESH1_IRQ,
+ MX28_LRADC_CH0_IRQ,
+ MX28_LRADC_CH1_IRQ,
+ MX28_LRADC_CH2_IRQ,
+ MX28_LRADC_CH3_IRQ,
+ MX28_LRADC_CH4_IRQ,
+ MX28_LRADC_CH5_IRQ,
+ MX28_LRADC_CH6_IRQ,
+ MX28_LRADC_CH7_IRQ,
+ MX28_LRADC_BUTTON0_IRQ,
+ MX28_LRADC_BUTTON1_IRQ,
+};
+
+static struct resource mx23_adc_resources[] = {
+ DEFINE_RES_MEM(0x0, 0x0),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH0_IRQ, "mxs-lradc-channel0"),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH1_IRQ, "mxs-lradc-channel1"),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH2_IRQ, "mxs-lradc-channel2"),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH3_IRQ, "mxs-lradc-channel3"),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH4_IRQ, "mxs-lradc-channel4"),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH5_IRQ, "mxs-lradc-channel5"),
+};
+
+static struct resource mx23_touchscreen_resources[] = {
+ DEFINE_RES_MEM(0x0, 0x0),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_TS_IRQ, "mxs-lradc-touchscreen"),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH6_IRQ, "mxs-lradc-channel6"),
+ DEFINE_RES_IRQ_NAMED(MX23_LRADC_CH7_IRQ, "mxs-lradc-channel7"),
+};
+
+static struct resource mx28_adc_resources[] = {
+ DEFINE_RES_MEM(0x0, 0x0),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_TRESH0_IRQ, "mxs-lradc-thresh0"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_TRESH1_IRQ, "mxs-lradc-thresh1"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH0_IRQ, "mxs-lradc-channel0"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH1_IRQ, "mxs-lradc-channel1"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH2_IRQ, "mxs-lradc-channel2"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH3_IRQ, "mxs-lradc-channel3"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH4_IRQ, "mxs-lradc-channel4"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH5_IRQ, "mxs-lradc-channel5"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_BUTTON0_IRQ, "mxs-lradc-button0"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_BUTTON1_IRQ, "mxs-lradc-button1"),
+};
+
+static struct resource mx28_touchscreen_resources[] = {
+ DEFINE_RES_MEM(0x0, 0x0),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_TS_IRQ, "mxs-lradc-touchscreen"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH6_IRQ, "mxs-lradc-channel6"),
+ DEFINE_RES_IRQ_NAMED(MX28_LRADC_CH7_IRQ, "mxs-lradc-channel7"),
+};
+
+static struct mfd_cell mx23_cells[] = {
+ {
+ .name = "mxs-lradc-adc",
+ .resources = mx23_adc_resources,
+ .num_resources = ARRAY_SIZE(mx23_adc_resources),
+ },
+ {
+ .name = "mxs-lradc-ts",
+ .resources = mx23_touchscreen_resources,
+ .num_resources = ARRAY_SIZE(mx23_touchscreen_resources),
+ },
+};
+
+static struct mfd_cell mx28_cells[] = {
+ {
+ .name = "mxs-lradc-adc",
+ .resources = mx28_adc_resources,
+ .num_resources = ARRAY_SIZE(mx28_adc_resources),
+ },
+ {
+ .name = "mxs-lradc-ts",
+ .resources = mx28_touchscreen_resources,
+ .num_resources = ARRAY_SIZE(mx28_touchscreen_resources),
+ }
+};
+
+static const struct of_device_id mxs_lradc_dt_ids[] = {
+ { .compatible = "fsl,imx23-lradc", .data = (void *)IMX23_LRADC, },
+ { .compatible = "fsl,imx28-lradc", .data = (void *)IMX28_LRADC, },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_lradc_dt_ids);
+
+static int mxs_lradc_probe(struct platform_device *pdev)
+{
+ const struct of_device_id *of_id;
+ struct device *dev = &pdev->dev;
+ struct device_node *node = dev->of_node;
+ struct mxs_lradc *lradc;
+ struct mfd_cell *cells = NULL;
+ struct resource *res;
+ int ret = 0;
+ u32 ts_wires = 0;
+
+ lradc = devm_kzalloc(&pdev->dev, sizeof(*lradc), GFP_KERNEL);
+ if (!lradc)
+ return -ENOMEM;
+
+ of_id = of_match_device(mxs_lradc_dt_ids, &pdev->dev);
+ if (!of_id)
+ return -EINVAL;
+
+ lradc->soc = (enum mxs_lradc_id)of_id->data;
+
+ lradc->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(lradc->clk)) {
+ dev_err(dev, "Failed to get the delay unit clock\n");
+ return PTR_ERR(lradc->clk);
+ }
+
+ ret = clk_prepare_enable(lradc->clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable the delay unit clock\n");
+ return ret;
+ }
+
+ ret = of_property_read_u32(node, "fsl,lradc-touchscreen-wires",
+ &ts_wires);
+
+ if (!ret) {
+ lradc->buffer_vchans = BUFFER_VCHANS_LIMITED;
+
+ switch (ts_wires) {
+ case 4:
+ lradc->touchscreen_wire = MXS_LRADC_TOUCHSCREEN_4WIRE;
+ break;
+ case 5:
+ if (lradc->soc == IMX28_LRADC) {
+ lradc->touchscreen_wire =
+ MXS_LRADC_TOUCHSCREEN_5WIRE;
+ break;
+ }
+ /* fall through to an error message for i.MX23 */
+ default:
+ dev_err(&pdev->dev,
+ "Unsupported number of touchscreen wires (%d)\n"
+ , ts_wires);
+ ret = -EINVAL;
+ goto err_clk;
+ }
+ } else {
+ lradc->buffer_vchans = BUFFER_VCHANS_ALL;
+ }
+
+ platform_set_drvdata(pdev, lradc);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENOMEM;
+
+ switch (lradc->soc) {
+ case IMX23_LRADC:
+ mx23_adc_resources[RES_MEM] = *res;
+ mx23_touchscreen_resources[RES_MEM] = *res;
+ cells = mx23_cells;
+ break;
+ case IMX28_LRADC:
+ mx28_adc_resources[RES_MEM] = *res;
+ mx28_touchscreen_resources[RES_MEM] = *res;
+ cells = mx28_cells;
+ break;
+ default:
+ dev_err(dev, "Unsupported SoC\n");
+ ret = -ENODEV;
+ goto err_clk;
+ }
+
+ ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE,
+ &cells[ADC_CELL], 1, NULL, 0, NULL);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to add the ADC subdevice\n");
+ goto err_clk;
+ }
+
+ if (!lradc->touchscreen_wire)
+ return 0;
+
+ ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE,
+ &cells[TSC_CELL], 1, NULL, 0, NULL);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Failed to add the touchscreen subdevice\n");
+ goto err_clk;
+ }
+
+ return 0;
+
+err_clk:
+ clk_disable_unprepare(lradc->clk);
+
+ return ret;
+}
+
+static int mxs_lradc_remove(struct platform_device *pdev)
+{
+ struct mxs_lradc *lradc = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(lradc->clk);
+
+ return 0;
+}
+
+static struct platform_driver mxs_lradc_driver = {
+ .driver = {
+ .name = "mxs-lradc",
+ .of_match_table = mxs_lradc_dt_ids,
+ },
+ .probe = mxs_lradc_probe,
+ .remove = mxs_lradc_remove,
+};
+module_platform_driver(mxs_lradc_driver);
+
+MODULE_AUTHOR("Ksenija Stanojevic <ksenija.stanojevic@gmail.com>");
+MODULE_DESCRIPTION("Freescale i.MX23/i.MX28 LRADC driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:mxs-lradc");
diff --git a/drivers/mfd/wm831x-core.c b/drivers/mfd/wm831x-core.c
index 3e0e99e..13a4c11 100644
--- a/drivers/mfd/wm831x-core.c
+++ b/drivers/mfd/wm831x-core.c
@@ -19,6 +19,8 @@
#include <linux/mfd/core.h>
#include <linux/slab.h>
#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/mfd/wm831x/core.h>
#include <linux/mfd/wm831x/pdata.h>
@@ -1613,12 +1615,24 @@ struct regmap_config wm831x_regmap_config = {
};
EXPORT_SYMBOL_GPL(wm831x_regmap_config);
+const struct of_device_id wm831x_of_match[] = {
+ { .compatible = "wlf,wm8310", .data = (void *)WM8310 },
+ { .compatible = "wlf,wm8311", .data = (void *)WM8311 },
+ { .compatible = "wlf,wm8312", .data = (void *)WM8312 },
+ { .compatible = "wlf,wm8320", .data = (void *)WM8320 },
+ { .compatible = "wlf,wm8321", .data = (void *)WM8321 },
+ { .compatible = "wlf,wm8325", .data = (void *)WM8325 },
+ { .compatible = "wlf,wm8326", .data = (void *)WM8326 },
+ { },
+};
+EXPORT_SYMBOL_GPL(wm831x_of_match);
+
/*
* Instantiate the generic non-control parts of the device.
*/
-int wm831x_device_init(struct wm831x *wm831x, unsigned long id, int irq)
+int wm831x_device_init(struct wm831x *wm831x, int irq)
{
- struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev);
+ struct wm831x_pdata *pdata = &wm831x->pdata;
int rev, wm831x_num;
enum wm831x_parent parent;
int ret, i;
@@ -1627,8 +1641,7 @@ int wm831x_device_init(struct wm831x *wm831x, unsigned long id, int irq)
mutex_init(&wm831x->key_lock);
dev_set_drvdata(wm831x->dev, wm831x);
- if (pdata)
- wm831x->soft_shutdown = pdata->soft_shutdown;
+ wm831x->soft_shutdown = pdata->soft_shutdown;
ret = wm831x_reg_read(wm831x, WM831X_PARENT_ID);
if (ret < 0) {
@@ -1663,7 +1676,7 @@ int wm831x_device_init(struct wm831x *wm831x, unsigned long id, int irq)
*/
if (ret == 0) {
dev_info(wm831x->dev, "Device is an engineering sample\n");
- ret = id;
+ ret = wm831x->type;
}
switch (ret) {
@@ -1736,9 +1749,9 @@ int wm831x_device_init(struct wm831x *wm831x, unsigned long id, int irq)
/* This will need revisiting in future but is OK for all
* current parts.
*/
- if (parent != id)
- dev_warn(wm831x->dev, "Device was registered as a WM%lx\n",
- id);
+ if (parent != wm831x->type)
+ dev_warn(wm831x->dev, "Device was registered as a WM%x\n",
+ wm831x->type);
/* Bootstrap the user key */
ret = wm831x_reg_read(wm831x, WM831X_SECURITY_KEY);
diff --git a/drivers/mfd/wm831x-i2c.c b/drivers/mfd/wm831x-i2c.c
index 824bcba..781af06 100644
--- a/drivers/mfd/wm831x-i2c.c
+++ b/drivers/mfd/wm831x-i2c.c
@@ -19,6 +19,8 @@
#include <linux/mfd/core.h>
#include <linux/slab.h>
#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/regmap.h>
#include <linux/mfd/wm831x/core.h>
@@ -27,15 +29,26 @@
static int wm831x_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
+ struct wm831x_pdata *pdata = dev_get_platdata(&i2c->dev);
+ const struct of_device_id *of_id;
struct wm831x *wm831x;
+ enum wm831x_parent type;
int ret;
+ if (i2c->dev.of_node) {
+ of_id = of_match_device(wm831x_of_match, &i2c->dev);
+ type = (enum wm831x_parent)of_id->data;
+ } else {
+ type = (enum wm831x_parent)id->driver_data;
+ }
+
wm831x = devm_kzalloc(&i2c->dev, sizeof(struct wm831x), GFP_KERNEL);
if (wm831x == NULL)
return -ENOMEM;
i2c_set_clientdata(i2c, wm831x);
wm831x->dev = &i2c->dev;
+ wm831x->type = type;
wm831x->regmap = devm_regmap_init_i2c(i2c, &wm831x_regmap_config);
if (IS_ERR(wm831x->regmap)) {
@@ -45,7 +58,10 @@ static int wm831x_i2c_probe(struct i2c_client *i2c,
return ret;
}
- return wm831x_device_init(wm831x, id->driver_data, i2c->irq);
+ if (pdata)
+ memcpy(&wm831x->pdata, pdata, sizeof(*pdata));
+
+ return wm831x_device_init(wm831x, i2c->irq);
}
static int wm831x_i2c_remove(struct i2c_client *i2c)
@@ -94,6 +110,7 @@ static struct i2c_driver wm831x_i2c_driver = {
.driver = {
.name = "wm831x",
.pm = &wm831x_pm_ops,
+ .of_match_table = of_match_ptr(wm831x_of_match),
},
.probe = wm831x_i2c_probe,
.remove = wm831x_i2c_remove,
diff --git a/drivers/mfd/wm831x-irq.c b/drivers/mfd/wm831x-irq.c
index dfea8b9..c01239a 100644
--- a/drivers/mfd/wm831x-irq.c
+++ b/drivers/mfd/wm831x-irq.c
@@ -564,7 +564,7 @@ static const struct irq_domain_ops wm831x_irq_domain_ops = {
int wm831x_irq_init(struct wm831x *wm831x, int irq)
{
- struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev);
+ struct wm831x_pdata *pdata = &wm831x->pdata;
struct irq_domain *domain;
int i, ret, irq_base;
@@ -579,7 +579,7 @@ int wm831x_irq_init(struct wm831x *wm831x, int irq)
}
/* Try to dynamically allocate IRQs if no base is specified */
- if (pdata && pdata->irq_base) {
+ if (pdata->irq_base) {
irq_base = irq_alloc_descs(pdata->irq_base, 0,
WM831X_NUM_IRQS, 0);
if (irq_base < 0) {
@@ -608,7 +608,7 @@ int wm831x_irq_init(struct wm831x *wm831x, int irq)
return -EINVAL;
}
- if (pdata && pdata->irq_cmos)
+ if (pdata->irq_cmos)
i = 0;
else
i = WM831X_IRQ_OD;
diff --git a/drivers/mfd/wm831x-spi.c b/drivers/mfd/wm831x-spi.c
index 80482ae..c332e28 100644
--- a/drivers/mfd/wm831x-spi.c
+++ b/drivers/mfd/wm831x-spi.c
@@ -14,6 +14,8 @@
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/pm.h>
#include <linux/spi/spi.h>
#include <linux/regmap.h>
@@ -23,12 +25,19 @@
static int wm831x_spi_probe(struct spi_device *spi)
{
+ struct wm831x_pdata *pdata = dev_get_platdata(&spi->dev);
const struct spi_device_id *id = spi_get_device_id(spi);
+ const struct of_device_id *of_id;
struct wm831x *wm831x;
enum wm831x_parent type;
int ret;
- type = (enum wm831x_parent)id->driver_data;
+ if (spi->dev.of_node) {
+ of_id = of_match_device(wm831x_of_match, &spi->dev);
+ type = (enum wm831x_parent)of_id->data;
+ } else {
+ type = (enum wm831x_parent)id->driver_data;
+ }
wm831x = devm_kzalloc(&spi->dev, sizeof(struct wm831x), GFP_KERNEL);
if (wm831x == NULL)
@@ -38,6 +47,7 @@ static int wm831x_spi_probe(struct spi_device *spi)
spi_set_drvdata(spi, wm831x);
wm831x->dev = &spi->dev;
+ wm831x->type = type;
wm831x->regmap = devm_regmap_init_spi(spi, &wm831x_regmap_config);
if (IS_ERR(wm831x->regmap)) {
@@ -47,7 +57,10 @@ static int wm831x_spi_probe(struct spi_device *spi)
return ret;
}
- return wm831x_device_init(wm831x, type, spi->irq);
+ if (pdata)
+ memcpy(&wm831x->pdata, pdata, sizeof(*pdata));
+
+ return wm831x_device_init(wm831x, spi->irq);
}
static int wm831x_spi_remove(struct spi_device *spi)
@@ -97,6 +110,7 @@ static struct spi_driver wm831x_spi_driver = {
.driver = {
.name = "wm831x",
.pm = &wm831x_spi_pm,
+ .of_match_table = of_match_ptr(wm831x_of_match),
},
.id_table = wm831x_spi_ids,
.probe = wm831x_spi_probe,
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index f9b4996..c0dfd31 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -777,6 +777,7 @@ exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
{
struct samsung_retention_ctrl *ctrl;
struct regmap *pmu_regs;
+ int i;
ctrl = devm_kzalloc(drvdata->dev, sizeof(*ctrl), GFP_KERNEL);
if (!ctrl)
@@ -794,6 +795,10 @@ exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
ctrl->enable = exynos_retention_enable;
ctrl->disable = exynos_retention_disable;
+ /* Ensure that retention is disabled on driver init */
+ for (i = 0; i < ctrl->nr_regs; i++)
+ regmap_write(pmu_regs, ctrl->regs[i], ctrl->value);
+
return ctrl;
}
@@ -1546,6 +1551,54 @@ static const struct samsung_pin_bank_data exynos5433_pin_banks9[] __initconst =
EXYNOS_PIN_BANK_EINTG(3, 0x000, "gpj1", 0x00),
};
+/* PMU pin retention groups registers for Exynos5433 (without audio & fsys) */
+static const u32 exynos5433_retention_regs[] = {
+ EXYNOS5433_PAD_RETENTION_TOP_OPTION,
+ EXYNOS5433_PAD_RETENTION_UART_OPTION,
+ EXYNOS5433_PAD_RETENTION_EBIA_OPTION,
+ EXYNOS5433_PAD_RETENTION_EBIB_OPTION,
+ EXYNOS5433_PAD_RETENTION_SPI_OPTION,
+ EXYNOS5433_PAD_RETENTION_MIF_OPTION,
+ EXYNOS5433_PAD_RETENTION_USBXTI_OPTION,
+ EXYNOS5433_PAD_RETENTION_BOOTLDO_OPTION,
+ EXYNOS5433_PAD_RETENTION_UFS_OPTION,
+ EXYNOS5433_PAD_RETENTION_FSYSGENIO_OPTION,
+};
+
+static const struct samsung_retention_data exynos5433_retention_data __initconst = {
+ .regs = exynos5433_retention_regs,
+ .nr_regs = ARRAY_SIZE(exynos5433_retention_regs),
+ .value = EXYNOS_WAKEUP_FROM_LOWPWR,
+ .refcnt = &exynos_shared_retention_refcnt,
+ .init = exynos_retention_init,
+};
+
+/* PMU retention control for audio pins can be tied to audio pin bank */
+static const u32 exynos5433_audio_retention_regs[] = {
+ EXYNOS5433_PAD_RETENTION_AUD_OPTION,
+};
+
+static const struct samsung_retention_data exynos5433_audio_retention_data __initconst = {
+ .regs = exynos5433_audio_retention_regs,
+ .nr_regs = ARRAY_SIZE(exynos5433_audio_retention_regs),
+ .value = EXYNOS_WAKEUP_FROM_LOWPWR,
+ .init = exynos_retention_init,
+};
+
+/* PMU retention control for mmc pins can be tied to fsys pin bank */
+static const u32 exynos5433_fsys_retention_regs[] = {
+ EXYNOS5433_PAD_RETENTION_MMC0_OPTION,
+ EXYNOS5433_PAD_RETENTION_MMC1_OPTION,
+ EXYNOS5433_PAD_RETENTION_MMC2_OPTION,
+};
+
+static const struct samsung_retention_data exynos5433_fsys_retention_data __initconst = {
+ .regs = exynos5433_fsys_retention_regs,
+ .nr_regs = ARRAY_SIZE(exynos5433_fsys_retention_regs),
+ .value = EXYNOS_WAKEUP_FROM_LOWPWR,
+ .init = exynos_retention_init,
+};
+
/*
* Samsung pinctrl driver data for Exynos5433 SoC. Exynos5433 SoC includes
* ten gpio/pin-mux/pinconfig controllers.
@@ -1559,6 +1612,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
.nr_ext_resources = 1,
+ .retention_data = &exynos5433_retention_data,
}, {
/* pin-controller instance 1 data */
.pin_banks = exynos5433_pin_banks1,
@@ -1566,6 +1620,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_audio_retention_data,
}, {
/* pin-controller instance 2 data */
.pin_banks = exynos5433_pin_banks2,
@@ -1573,6 +1628,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_retention_data,
}, {
/* pin-controller instance 3 data */
.pin_banks = exynos5433_pin_banks3,
@@ -1580,6 +1636,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_retention_data,
}, {
/* pin-controller instance 4 data */
.pin_banks = exynos5433_pin_banks4,
@@ -1587,6 +1644,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_retention_data,
}, {
/* pin-controller instance 5 data */
.pin_banks = exynos5433_pin_banks5,
@@ -1594,6 +1652,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_fsys_retention_data,
}, {
/* pin-controller instance 6 data */
.pin_banks = exynos5433_pin_banks6,
@@ -1601,6 +1660,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_retention_data,
}, {
/* pin-controller instance 7 data */
.pin_banks = exynos5433_pin_banks7,
@@ -1608,6 +1668,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_retention_data,
}, {
/* pin-controller instance 8 data */
.pin_banks = exynos5433_pin_banks8,
@@ -1615,6 +1676,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_retention_data,
}, {
/* pin-controller instance 9 data */
.pin_banks = exynos5433_pin_banks9,
@@ -1622,6 +1684,7 @@ const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
.eint_gpio_init = exynos_eint_gpio_init,
.suspend = exynos_pinctrl_suspend,
.resume = exynos_pinctrl_resume,
+ .retention_data = &exynos5433_retention_data,
},
};
diff --git a/include/linux/mfd/motorola-cpcap.h b/include/linux/mfd/motorola-cpcap.h
index 793aa69..aefc49c 100644
--- a/include/linux/mfd/motorola-cpcap.h
+++ b/include/linux/mfd/motorola-cpcap.h
@@ -14,6 +14,9 @@
* published by the Free Software Foundation.
*/
+#include <linux/device.h>
+#include <linux/regmap.h>
+
#define CPCAP_VENDOR_ST 0
#define CPCAP_VENDOR_TI 1
diff --git a/include/linux/mfd/mxs-lradc.h b/include/linux/mfd/mxs-lradc.h
new file mode 100644
index 0000000..661a452
--- /dev/null
+++ b/include/linux/mfd/mxs-lradc.h
@@ -0,0 +1,187 @@
+/*
+ * Freescale MXS Low Resolution Analog-to-Digital Converter driver
+ *
+ * Copyright (c) 2012 DENX Software Engineering, GmbH.
+ * Copyright (c) 2016 Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
+ *
+ * Author: Marek Vasut <marex@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MFD_MXS_LRADC_H
+#define __MFD_MXS_LRADC_H
+
+#include <linux/bitops.h>
+#include <linux/io.h>
+#include <linux/stmp_device.h>
+
+#define LRADC_MAX_DELAY_CHANS 4
+#define LRADC_MAX_MAPPED_CHANS 8
+#define LRADC_MAX_TOTAL_CHANS 16
+
+#define LRADC_DELAY_TIMER_HZ 2000
+
+#define LRADC_CTRL0 0x00
+# define LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE BIT(23)
+# define LRADC_CTRL0_MX28_TOUCH_SCREEN_TYPE BIT(22)
+# define LRADC_CTRL0_MX28_YNNSW /* YM */ BIT(21)
+# define LRADC_CTRL0_MX28_YPNSW /* YP */ BIT(20)
+# define LRADC_CTRL0_MX28_YPPSW /* YP */ BIT(19)
+# define LRADC_CTRL0_MX28_XNNSW /* XM */ BIT(18)
+# define LRADC_CTRL0_MX28_XNPSW /* XM */ BIT(17)
+# define LRADC_CTRL0_MX28_XPPSW /* XP */ BIT(16)
+
+# define LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE BIT(20)
+# define LRADC_CTRL0_MX23_YM BIT(19)
+# define LRADC_CTRL0_MX23_XM BIT(18)
+# define LRADC_CTRL0_MX23_YP BIT(17)
+# define LRADC_CTRL0_MX23_XP BIT(16)
+
+# define LRADC_CTRL0_MX28_PLATE_MASK \
+ (LRADC_CTRL0_MX28_TOUCH_DETECT_ENABLE | \
+ LRADC_CTRL0_MX28_YNNSW | LRADC_CTRL0_MX28_YPNSW | \
+ LRADC_CTRL0_MX28_YPPSW | LRADC_CTRL0_MX28_XNNSW | \
+ LRADC_CTRL0_MX28_XNPSW | LRADC_CTRL0_MX28_XPPSW)
+
+# define LRADC_CTRL0_MX23_PLATE_MASK \
+ (LRADC_CTRL0_MX23_TOUCH_DETECT_ENABLE | \
+ LRADC_CTRL0_MX23_YM | LRADC_CTRL0_MX23_XM | \
+ LRADC_CTRL0_MX23_YP | LRADC_CTRL0_MX23_XP)
+
+#define LRADC_CTRL1 0x10
+#define LRADC_CTRL1_TOUCH_DETECT_IRQ_EN BIT(24)
+#define LRADC_CTRL1_LRADC_IRQ_EN(n) (1 << ((n) + 16))
+#define LRADC_CTRL1_MX28_LRADC_IRQ_EN_MASK (0x1fff << 16)
+#define LRADC_CTRL1_MX23_LRADC_IRQ_EN_MASK (0x01ff << 16)
+#define LRADC_CTRL1_LRADC_IRQ_EN_OFFSET 16
+#define LRADC_CTRL1_TOUCH_DETECT_IRQ BIT(8)
+#define LRADC_CTRL1_LRADC_IRQ(n) BIT(n)
+#define LRADC_CTRL1_MX28_LRADC_IRQ_MASK 0x1fff
+#define LRADC_CTRL1_MX23_LRADC_IRQ_MASK 0x01ff
+#define LRADC_CTRL1_LRADC_IRQ_OFFSET 0
+
+#define LRADC_CTRL2 0x20
+#define LRADC_CTRL2_DIVIDE_BY_TWO_OFFSET 24
+#define LRADC_CTRL2_TEMPSENSE_PWD BIT(15)
+
+#define LRADC_STATUS 0x40
+#define LRADC_STATUS_TOUCH_DETECT_RAW BIT(0)
+
+#define LRADC_CH(n) (0x50 + (0x10 * (n)))
+#define LRADC_CH_ACCUMULATE BIT(29)
+#define LRADC_CH_NUM_SAMPLES_MASK (0x1f << 24)
+#define LRADC_CH_NUM_SAMPLES_OFFSET 24
+#define LRADC_CH_NUM_SAMPLES(x) \
+ ((x) << LRADC_CH_NUM_SAMPLES_OFFSET)
+#define LRADC_CH_VALUE_MASK 0x3ffff
+#define LRADC_CH_VALUE_OFFSET 0
+
+#define LRADC_DELAY(n) (0xd0 + (0x10 * (n)))
+#define LRADC_DELAY_TRIGGER_LRADCS_MASK (0xffUL << 24)
+#define LRADC_DELAY_TRIGGER_LRADCS_OFFSET 24
+#define LRADC_DELAY_TRIGGER(x) \
+ (((x) << LRADC_DELAY_TRIGGER_LRADCS_OFFSET) & \
+ LRADC_DELAY_TRIGGER_LRADCS_MASK)
+#define LRADC_DELAY_KICK BIT(20)
+#define LRADC_DELAY_TRIGGER_DELAYS_MASK (0xf << 16)
+#define LRADC_DELAY_TRIGGER_DELAYS_OFFSET 16
+#define LRADC_DELAY_TRIGGER_DELAYS(x) \
+ (((x) << LRADC_DELAY_TRIGGER_DELAYS_OFFSET) & \
+ LRADC_DELAY_TRIGGER_DELAYS_MASK)
+#define LRADC_DELAY_LOOP_COUNT_MASK (0x1f << 11)
+#define LRADC_DELAY_LOOP_COUNT_OFFSET 11
+#define LRADC_DELAY_LOOP(x) \
+ (((x) << LRADC_DELAY_LOOP_COUNT_OFFSET) & \
+ LRADC_DELAY_LOOP_COUNT_MASK)
+#define LRADC_DELAY_DELAY_MASK 0x7ff
+#define LRADC_DELAY_DELAY_OFFSET 0
+#define LRADC_DELAY_DELAY(x) \
+ (((x) << LRADC_DELAY_DELAY_OFFSET) & \
+ LRADC_DELAY_DELAY_MASK)
+
+#define LRADC_CTRL4 0x140
+#define LRADC_CTRL4_LRADCSELECT_MASK(n) (0xf << ((n) * 4))
+#define LRADC_CTRL4_LRADCSELECT_OFFSET(n) ((n) * 4)
+#define LRADC_CTRL4_LRADCSELECT(n, x) \
+ (((x) << LRADC_CTRL4_LRADCSELECT_OFFSET(n)) & \
+ LRADC_CTRL4_LRADCSELECT_MASK(n))
+
+#define LRADC_RESOLUTION 12
+#define LRADC_SINGLE_SAMPLE_MASK ((1 << LRADC_RESOLUTION) - 1)
+
+#define BUFFER_VCHANS_LIMITED 0x3f
+#define BUFFER_VCHANS_ALL 0xff
+
+ /*
+ * Certain LRADC channels are shared between touchscreen
+ * and/or touch-buttons and generic LRADC block. Therefore when using
+ * either of these, these channels are not available for the regular
+ * sampling. The shared channels are as follows:
+ *
+ * CH0 -- Touch button #0
+ * CH1 -- Touch button #1
+ * CH2 -- Touch screen XPUL
+ * CH3 -- Touch screen YPLL
+ * CH4 -- Touch screen XNUL
+ * CH5 -- Touch screen YNLR
+ * CH6 -- Touch screen WIPER (5-wire only)
+ *
+ * The bit fields below represents which parts of the LRADC block are
+ * switched into special mode of operation. These channels can not
+ * be sampled as regular LRADC channels. The driver will refuse any
+ * attempt to sample these channels.
+ */
+#define CHAN_MASK_TOUCHBUTTON (BIT(1) | BIT(0))
+#define CHAN_MASK_TOUCHSCREEN_4WIRE (0xf << 2)
+#define CHAN_MASK_TOUCHSCREEN_5WIRE (0x1f << 2)
+
+enum mxs_lradc_id {
+ IMX23_LRADC,
+ IMX28_LRADC,
+};
+
+enum mxs_lradc_ts_wires {
+ MXS_LRADC_TOUCHSCREEN_NONE = 0,
+ MXS_LRADC_TOUCHSCREEN_4WIRE,
+ MXS_LRADC_TOUCHSCREEN_5WIRE,
+};
+
+/**
+ * struct mxs_lradc
+ * @soc: soc type (IMX23 or IMX28)
+ * @clk: 2 kHz clock for delay units
+ * @buffer_vchans: channels that can be used during buffered capture
+ * @touchscreen_wire: touchscreen type (4-wire or 5-wire)
+ * @use_touchbutton: button state (on or off)
+ */
+struct mxs_lradc {
+ enum mxs_lradc_id soc;
+ struct clk *clk;
+ u8 buffer_vchans;
+
+ enum mxs_lradc_ts_wires touchscreen_wire;
+ bool use_touchbutton;
+};
+
+static inline u32 mxs_lradc_irq_mask(struct mxs_lradc *lradc)
+{
+ switch (lradc->soc) {
+ case IMX23_LRADC:
+ return LRADC_CTRL1_MX23_LRADC_IRQ_MASK;
+ case IMX28_LRADC:
+ return LRADC_CTRL1_MX28_LRADC_IRQ_MASK;
+ default:
+ return 0;
+ }
+}
+
+#endif /* __MXS_LRADC_H */
diff --git a/include/linux/mfd/wm831x/core.h b/include/linux/mfd/wm831x/core.h
index 76c2264..b49fa676 100644
--- a/include/linux/mfd/wm831x/core.h
+++ b/include/linux/mfd/wm831x/core.h
@@ -21,6 +21,8 @@
#include <linux/list.h>
#include <linux/regmap.h>
#include <linux/mfd/wm831x/auxadc.h>
+#include <linux/mfd/wm831x/pdata.h>
+#include <linux/of.h>
/*
* Register values.
@@ -367,6 +369,9 @@ struct wm831x {
struct regmap *regmap;
+ struct wm831x_pdata pdata;
+ enum wm831x_parent type;
+
int irq; /* Our chip IRQ */
struct mutex irq_lock;
struct irq_domain *irq_domain;
@@ -412,7 +417,7 @@ int wm831x_set_bits(struct wm831x *wm831x, unsigned short reg,
int wm831x_bulk_read(struct wm831x *wm831x, unsigned short reg,
int count, u16 *buf);
-int wm831x_device_init(struct wm831x *wm831x, unsigned long id, int irq);
+int wm831x_device_init(struct wm831x *wm831x, int irq);
void wm831x_device_exit(struct wm831x *wm831x);
int wm831x_device_suspend(struct wm831x *wm831x);
void wm831x_device_shutdown(struct wm831x *wm831x);
@@ -427,4 +432,6 @@ static inline int wm831x_irq(struct wm831x *wm831x, int irq)
extern struct regmap_config wm831x_regmap_config;
+extern const struct of_device_id wm831x_of_match[];
+
#endif
