/*
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 *
 * Clean ups from Moschip version and a few ioctl implementations by:
 *	Paul B Schroeder <pschroeder "at" uplogix "dot" com>
 *
 * Originally based on drivers/usb/serial/io_edgeport.c which is:
 *      Copyright (C) 2000 Inside Out Networks, All rights reserved.
 *      Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
 *
 */

#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/serial.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>
#include <linux/uaccess.h>

/*
 * Version Information
 */
#define DRIVER_VERSION "1.3.2"
#define DRIVER_DESC "Moschip 7840/7820 USB Serial Driver"

/*
 * 16C50 UART register defines
 */

#define LCR_BITS_5             0x00	/* 5 bits/char */
#define LCR_BITS_6             0x01	/* 6 bits/char */
#define LCR_BITS_7             0x02	/* 7 bits/char */
#define LCR_BITS_8             0x03	/* 8 bits/char */
#define LCR_BITS_MASK          0x03	/* Mask for bits/char field */

#define LCR_STOP_1             0x00	/* 1 stop bit */
#define LCR_STOP_1_5           0x04	/* 1.5 stop bits (if 5   bits/char) */
#define LCR_STOP_2             0x04	/* 2 stop bits   (if 6-8 bits/char) */
#define LCR_STOP_MASK          0x04	/* Mask for stop bits field */

#define LCR_PAR_NONE           0x00	/* No parity */
#define LCR_PAR_ODD            0x08	/* Odd parity */
#define LCR_PAR_EVEN           0x18	/* Even parity */
#define LCR_PAR_MARK           0x28	/* Force parity bit to 1 */
#define LCR_PAR_SPACE          0x38	/* Force parity bit to 0 */
#define LCR_PAR_MASK           0x38	/* Mask for parity field */

#define LCR_SET_BREAK          0x40	/* Set Break condition */
#define LCR_DL_ENABLE          0x80	/* Enable access to divisor latch */

#define MCR_DTR                0x01	/* Assert DTR */
#define MCR_RTS                0x02	/* Assert RTS */
#define MCR_OUT1               0x04	/* Loopback only: Sets state of RI */
#define MCR_MASTER_IE          0x08	/* Enable interrupt outputs */
#define MCR_LOOPBACK           0x10	/* Set internal (digital) loopback mode */
#define MCR_XON_ANY            0x20	/* Enable any char to exit XOFF mode */

#define MOS7840_MSR_CTS        0x10	/* Current state of CTS */
#define MOS7840_MSR_DSR        0x20	/* Current state of DSR */
#define MOS7840_MSR_RI         0x40	/* Current state of RI */
#define MOS7840_MSR_CD         0x80	/* Current state of CD */

/*
 * Defines used for sending commands to port
 */

#define WAIT_FOR_EVER   (HZ * 0)	/* timeout urb is wait for ever */
#define MOS_WDR_TIMEOUT (HZ * 5)	/* default urb timeout */

#define MOS_PORT1       0x0200
#define MOS_PORT2       0x0300
#define MOS_VENREG      0x0000
#define MOS_MAX_PORT	0x02
#define MOS_WRITE       0x0E
#define MOS_READ        0x0D

/* Requests */
#define MCS_RD_RTYPE    0xC0
#define MCS_WR_RTYPE    0x40
#define MCS_RDREQ       0x0D
#define MCS_WRREQ       0x0E
#define MCS_CTRL_TIMEOUT        500
#define VENDOR_READ_LENGTH      (0x01)

#define MAX_NAME_LEN    64

#define ZLP_REG1  0x3A		/* Zero_Flag_Reg1    58 */
#define ZLP_REG5  0x3E		/* Zero_Flag_Reg5    62 */

/* For higher baud Rates use TIOCEXBAUD */
#define TIOCEXBAUD     0x5462

/* vendor id and device id defines */

/* The native mos7840/7820 component */
#define USB_VENDOR_ID_MOSCHIP           0x9710
#define MOSCHIP_DEVICE_ID_7840          0x7840
#define MOSCHIP_DEVICE_ID_7820          0x7820
/* The native component can have its vendor/device id's overridden
 * in vendor-specific implementations.  Such devices can be handled
 * by making a change here, in moschip_port_id_table, and in
 * moschip_id_table_combined
 */
#define USB_VENDOR_ID_BANDB              0x0856
#define BANDB_DEVICE_ID_USO9ML2_2        0xAC22
#define BANDB_DEVICE_ID_USO9ML2_2P       0xBC00
#define BANDB_DEVICE_ID_USO9ML2_4        0xAC24
#define BANDB_DEVICE_ID_USO9ML2_4P       0xBC01
#define BANDB_DEVICE_ID_US9ML2_2         0xAC29
#define BANDB_DEVICE_ID_US9ML2_4         0xAC30
#define BANDB_DEVICE_ID_USPTL4_2         0xAC31
#define BANDB_DEVICE_ID_USPTL4_4         0xAC32
#define BANDB_DEVICE_ID_USOPTL4_2        0xAC42
#define BANDB_DEVICE_ID_USOPTL4_2P       0xBC02
#define BANDB_DEVICE_ID_USOPTL4_4        0xAC44
#define BANDB_DEVICE_ID_USOPTL4_4P       0xBC03
#define BANDB_DEVICE_ID_USOPTL2_4        0xAC24

/* This driver also supports
 * ATEN UC2324 device using Moschip MCS7840
 * ATEN UC2322 device using Moschip MCS7820
 */
#define USB_VENDOR_ID_ATENINTL		0x0557
#define ATENINTL_DEVICE_ID_UC2324	0x2011
#define ATENINTL_DEVICE_ID_UC2322	0x7820

/* Interrupt Routine Defines    */

#define SERIAL_IIR_RLS      0x06
#define SERIAL_IIR_MS       0x00

/*
 *  Emulation of the bit mask on the LINE STATUS REGISTER.
 */
#define SERIAL_LSR_DR       0x0001
#define SERIAL_LSR_OE       0x0002
#define SERIAL_LSR_PE       0x0004
#define SERIAL_LSR_FE       0x0008
#define SERIAL_LSR_BI       0x0010

#define MOS_MSR_DELTA_CTS   0x10
#define MOS_MSR_DELTA_DSR   0x20
#define MOS_MSR_DELTA_RI    0x40
#define MOS_MSR_DELTA_CD    0x80

/* Serial Port register Address */
#define INTERRUPT_ENABLE_REGISTER  ((__u16)(0x01))
#define FIFO_CONTROL_REGISTER      ((__u16)(0x02))
#define LINE_CONTROL_REGISTER      ((__u16)(0x03))
#define MODEM_CONTROL_REGISTER     ((__u16)(0x04))
#define LINE_STATUS_REGISTER       ((__u16)(0x05))
#define MODEM_STATUS_REGISTER      ((__u16)(0x06))
#define SCRATCH_PAD_REGISTER       ((__u16)(0x07))
#define DIVISOR_LATCH_LSB          ((__u16)(0x00))
#define DIVISOR_LATCH_MSB          ((__u16)(0x01))

#define CLK_MULTI_REGISTER         ((__u16)(0x02))
#define CLK_START_VALUE_REGISTER   ((__u16)(0x03))
#define GPIO_REGISTER              ((__u16)(0x07))

#define SERIAL_LCR_DLAB            ((__u16)(0x0080))

/*
 * URB POOL related defines
 */
#define NUM_URBS                        16	/* URB Count */
#define URB_TRANSFER_BUFFER_SIZE        32	/* URB Size  */


static const struct usb_device_id moschip_port_id_table[] = {
	{USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7840)},
	{USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7820)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2P)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4P)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_2)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_4)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_2)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_4)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2P)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4P)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL2_4)},
	{USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)},
	{USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)},
	{}			/* terminating entry */
};

static const struct usb_device_id moschip_id_table_combined[] __devinitconst = {
	{USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7840)},
	{USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7820)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2P)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4P)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_2)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_4)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_2)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_4)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2P)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4P)},
	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL2_4)},
	{USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)},
	{USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)},
	{}			/* terminating entry */
};

MODULE_DEVICE_TABLE(usb, moschip_id_table_combined);

/* This structure holds all of the local port information */

struct moschip_port {
	int port_num;		/*Actual port number in the device(1,2,etc) */
	struct urb *write_urb;	/* write URB for this port */
	struct urb *read_urb;	/* read URB for this port */
	struct urb *int_urb;
	__u8 shadowLCR;		/* last LCR value received */
	__u8 shadowMCR;		/* last MCR value received */
	char open;
	char open_ports;
	char zombie;
	wait_queue_head_t wait_chase;	/* for handling sleeping while waiting for chase to finish */
	wait_queue_head_t delta_msr_wait;	/* for handling sleeping while waiting for msr change to happen */
	int delta_msr_cond;
	struct async_icount icount;
	struct usb_serial_port *port;	/* loop back to the owner of this object */

	/* Offsets */
	__u8 SpRegOffset;
	__u8 ControlRegOffset;
	__u8 DcrRegOffset;
	/* for processing control URBS in interrupt context */
	struct urb *control_urb;
	struct usb_ctrlrequest *dr;
	char *ctrl_buf;
	int MsrLsr;

	spinlock_t pool_lock;
	struct urb *write_urb_pool[NUM_URBS];
	char busy[NUM_URBS];
	bool read_urb_busy;
};


static bool debug;

/*
 * mos7840_set_reg_sync
 * 	To set the Control register by calling usb_fill_control_urb function
 *	by passing usb_sndctrlpipe function as parameter.
 */

static int mos7840_set_reg_sync(struct usb_serial_port *port, __u16 reg,
				__u16 val)
{
	struct usb_device *dev = port->serial->dev;
	val = val & 0x00ff;
	dbg("mos7840_set_reg_sync offset is %x, value %x", reg, val);

	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ,
			       MCS_WR_RTYPE, val, reg, NULL, 0,
			       MOS_WDR_TIMEOUT);
}

/*
 * mos7840_get_reg_sync
 * 	To set the Uart register by calling usb_fill_control_urb function by
 *	passing usb_rcvctrlpipe function as parameter.
 */

static int mos7840_get_reg_sync(struct usb_serial_port *port, __u16 reg,
				__u16 *val)
{
	struct usb_device *dev = port->serial->dev;
	int ret = 0;
	u8 *buf;

	buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
	if (!buf)
		return -ENOMEM;

	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ,
			      MCS_RD_RTYPE, 0, reg, buf, VENDOR_READ_LENGTH,
			      MOS_WDR_TIMEOUT);
	*val = buf[0];
	dbg("mos7840_get_reg_sync offset is %x, return val %x", reg, *val);

	kfree(buf);
	return ret;
}

/*
 * mos7840_set_uart_reg
 *	To set the Uart register by calling usb_fill_control_urb function by
 *	passing usb_sndctrlpipe function as parameter.
 */

static int mos7840_set_uart_reg(struct usb_serial_port *port, __u16 reg,
				__u16 val)
{

	struct usb_device *dev = port->serial->dev;
	val = val & 0x00ff;
	/* For the UART control registers, the application number need
	   to be Or'ed */
	if (port->serial->num_ports == 4) {
		val |= (((__u16) port->number -
				(__u16) (port->serial->minor)) + 1) << 8;
		dbg("mos7840_set_uart_reg application number is %x", val);
	} else {
		if (((__u16) port->number - (__u16) (port->serial->minor)) == 0) {
			val |= (((__u16) port->number -
			      (__u16) (port->serial->minor)) + 1) << 8;
			dbg("mos7840_set_uart_reg application number is %x",
			    val);
		} else {
			val |=
			    (((__u16) port->number -
			      (__u16) (port->serial->minor)) + 2) << 8;
			dbg("mos7840_set_uart_reg application number is %x",
			    val);
		}
	}
	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ,
			       MCS_WR_RTYPE, val, reg, NULL, 0,
			       MOS_WDR_TIMEOUT);

}

/*
 * mos7840_get_uart_reg
 *	To set the Control register by calling usb_fill_control_urb function
 *	by passing usb_rcvctrlpipe function as parameter.
 */
static int mos7840_get_uart_reg(struct usb_serial_port *port, __u16 reg,
				__u16 *val)
{
	struct usb_device *dev = port->serial->dev;
	int ret = 0;
	__u16 Wval;
	u8 *buf;

	buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
	if (!buf)
		return -ENOMEM;

	/* dbg("application number is %4x",
	    (((__u16)port->number - (__u16)(port->serial->minor))+1)<<8); */
	/* Wval  is same as application number */
	if (port->serial->num_ports == 4) {
		Wval =
		    (((__u16) port->number - (__u16) (port->serial->minor)) +
		     1) << 8;
		dbg("mos7840_get_uart_reg application number is %x", Wval);
	} else {
		if (((__u16) port->number - (__u16) (port->serial->minor)) == 0) {
			Wval = (((__u16) port->number -
			      (__u16) (port->serial->minor)) + 1) << 8;
			dbg("mos7840_get_uart_reg application number is %x",
			    Wval);
		} else {
			Wval = (((__u16) port->number -
			      (__u16) (port->serial->minor)) + 2) << 8;
			dbg("mos7840_get_uart_reg application number is %x",
			    Wval);
		}
	}
	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ,
			      MCS_RD_RTYPE, Wval, reg, buf, VENDOR_READ_LENGTH,
			      MOS_WDR_TIMEOUT);
	*val = buf[0];

	kfree(buf);
	return ret;
}

static void mos7840_dump_serial_port(struct moschip_port *mos7840_port)
{

	dbg("***************************************");
	dbg("SpRegOffset is %2x", mos7840_port->SpRegOffset);
	dbg("ControlRegOffset is %2x", mos7840_port->ControlRegOffset);
	dbg("DCRRegOffset is %2x", mos7840_port->DcrRegOffset);
	dbg("***************************************");

}

/************************************************************************/
/************************************************************************/
/*             I N T E R F A C E   F U N C T I O N S			*/
/*             I N T E R F A C E   F U N C T I O N S			*/
/************************************************************************/
/************************************************************************/

static inline void mos7840_set_port_private(struct usb_serial_port *port,
					    struct moschip_port *data)
{
	usb_set_serial_port_data(port, (void *)data);
}

static inline struct moschip_port *mos7840_get_port_private(struct
							    usb_serial_port
							    *port)
{
	return (struct moschip_port *)usb_get_serial_port_data(port);
}

static void mos7840_handle_new_msr(struct moschip_port *port, __u8 new_msr)
{
	struct moschip_port *mos7840_port;
	struct async_icount *icount;
	mos7840_port = port;
	icount = &mos7840_port->icount;
	if (new_msr &
	    (MOS_MSR_DELTA_CTS | MOS_MSR_DELTA_DSR | MOS_MSR_DELTA_RI |
	     MOS_MSR_DELTA_CD)) {
		icount = &mos7840_port->icount;

		/* update input line counters */
		if (new_msr & MOS_MSR_DELTA_CTS) {
			icount->cts++;
			smp_wmb();
		}
		if (new_msr & MOS_MSR_DELTA_DSR) {
			icount->dsr++;
			smp_wmb();
		}
		if (new_msr & MOS_MSR_DELTA_CD) {
			icount->dcd++;
			smp_wmb();
		}
		if (new_msr & MOS_MSR_DELTA_RI) {
			icount->rng++;
			smp_wmb();
		}
	}
}

static void mos7840_handle_new_lsr(struct moschip_port *port, __u8 new_lsr)
{
	struct async_icount *icount;

	dbg("%s - %02x", __func__, new_lsr);

	if (new_lsr & SERIAL_LSR_BI) {
		/*
		 * Parity and Framing errors only count if they
		 * occur exclusive of a break being
		 * received.
		 */
		new_lsr &= (__u8) (SERIAL_LSR_OE | SERIAL_LSR_BI);
	}

	/* update input line counters */
	icount = &port->icount;
	if (new_lsr & SERIAL_LSR_BI) {
		icount->brk++;
		smp_wmb();
	}
	if (new_lsr & SERIAL_LSR_OE) {
		icount->overrun++;
		smp_wmb();
	}
	if (new_lsr & SERIAL_LSR_PE) {
		icount->parity++;
		smp_wmb();
	}
	if (new_lsr & SERIAL_LSR_FE) {
		icount->frame++;
		smp_wmb();
	}
}

/************************************************************************/
/************************************************************************/
/*            U S B  C A L L B A C K   F U N C T I O N S                */
/*            U S B  C A L L B A C K   F U N C T I O N S                */
/************************************************************************/
/************************************************************************/

static void mos7840_control_callback(struct urb *urb)
{
	unsigned char *data;
	struct moschip_port *mos7840_port;
	__u8 regval = 0x0;
	int result = 0;
	int status = urb->status;

	mos7840_port = urb->context;

	switch (status) {
	case 0:
		/* success */
		break;
	case -ECONNRESET:
	case -ENOENT:
	case -ESHUTDOWN:
		/* this urb is terminated, clean up */
		dbg("%s - urb shutting down with status: %d", __func__,
		    status);
		return;
	default:
		dbg("%s - nonzero urb status received: %d", __func__,
		    status);
		goto exit;
	}

	dbg("%s urb buffer size is %d", __func__, urb->actual_length);
	dbg("%s mos7840_port->MsrLsr is %d port %d", __func__,
	    mos7840_port->MsrLsr, mos7840_port->port_num);
	data = urb->transfer_buffer;
	regval = (__u8) data[0];
	dbg("%s data is %x", __func__, regval);
	if (mos7840_port->MsrLsr == 0)
		mos7840_handle_new_msr(mos7840_port, regval);
	else if (mos7840_port->MsrLsr == 1)
		mos7840_handle_new_lsr(mos7840_port, regval);

exit:
	spin_lock(&mos7840_port->pool_lock);
	if (!mos7840_port->zombie)
		result = usb_submit_urb(mos7840_port->int_urb, GFP_ATOMIC);
	spin_unlock(&mos7840_port->pool_lock);
	if (result) {
		dev_err(&urb->dev->dev,
			"%s - Error %d submitting interrupt urb\n",
			__func__, result);
	}
}

static int mos7840_get_reg(struct moschip_port *mcs, __u16 Wval, __u16 reg,
			   __u16 *val)
{
	struct usb_device *dev = mcs->port->serial->dev;
	struct usb_ctrlrequest *dr = mcs->dr;
	unsigned char *buffer = mcs->ctrl_buf;
	int ret;

	dr->bRequestType = MCS_RD_RTYPE;
	dr->bRequest = MCS_RDREQ;
	dr->wValue = cpu_to_le16(Wval);	/* 0 */
	dr->wIndex = cpu_to_le16(reg);
	dr->wLength = cpu_to_le16(2);

	usb_fill_control_urb(mcs->control_urb, dev, usb_rcvctrlpipe(dev, 0),
			     (unsigned char *)dr, buffer, 2,
			     mos7840_control_callback, mcs);
	mcs->control_urb->transfer_buffer_length = 2;
	ret = usb_submit_urb(mcs->control_urb, GFP_ATOMIC);
	return ret;
}

/*****************************************************************************
 * mos7840_interrupt_callback
 *	this is the callback function for when we have received data on the
 *	interrupt endpoint.
 *****************************************************************************/

static void mos7840_interrupt_callback(struct urb *urb)
{
	int result;
	int length;
	struct moschip_port *mos7840_port;
	struct usb_serial *serial;
	__u16 Data;
	unsigned char *data;
	__u8 sp[5], st;
	int i, rv = 0;
	__u16 wval, wreg = 0;
	int status = urb->status;

	dbg("%s", " : Entering");

	switch (status) {
	case 0:
		/* success */
		break;
	case -ECONNRESET:
	case -ENOENT:
	case -ESHUTDOWN:
		/* this urb is terminated, clean up */
		dbg("%s - urb shutting down with status: %d", __func__,
		    status);
		return;
	default:
		dbg("%s - nonzero urb status received: %d", __func__,
		    status);
		goto exit;
	}

	length = urb->actual_length;
	data = urb->transfer_buffer;

	serial = urb->context;

	/* Moschip get 5 bytes
	 * Byte 1 IIR Port 1 (port.number is 0)
	 * Byte 2 IIR Port 2 (port.number is 1)
	 * Byte 3 IIR Port 3 (port.number is 2)
	 * Byte 4 IIR Port 4 (port.number is 3)
	 * Byte 5 FIFO status for both */

	if (length && length > 5) {
		dbg("%s", "Wrong data !!!");
		return;
	}

	sp[0] = (__u8) data[0];
	sp[1] = (__u8) data[1];
	sp[2] = (__u8) data[2];
	sp[3] = (__u8) data[3];
	st = (__u8) data[4];

	for (i = 0; i < serial->num_ports; i++) {
		mos7840_port = mos7840_get_port_private(serial->port[i]);
		wval =
		    (((__u16) serial->port[i]->number -
		      (__u16) (serial->minor)) + 1) << 8;
		if (mos7840_port->open) {
			if (sp[i] & 0x01) {
				dbg("SP%d No Interrupt !!!", i);
			} else {
				switch (sp[i] & 0x0f) {
				case SERIAL_IIR_RLS:
					dbg("Serial Port %d: Receiver status error or ", i);
					dbg("address bit detected in 9-bit mode");
					mos7840_port->MsrLsr = 1;
					wreg = LINE_STATUS_REGISTER;
					break;
				case SERIAL_IIR_MS:
					dbg("Serial Port %d: Modem status change", i);
					mos7840_port->MsrLsr = 0;
					wreg = MODEM_STATUS_REGISTER;
					break;
				}
				spin_lock(&mos7840_port->pool_lock);
				if (!mos7840_port->zombie) {
					rv = mos7840_get_reg(mos7840_port, wval, wreg, &Data);
				} else {
					spin_unlock(&mos7840_port->pool_lock);
					return;
				}
				spin_unlock(&mos7840_port->pool_lock);
			}
		}
	}
	if (!(rv < 0))
		/* the completion handler for the control urb will resubmit */
		return;
exit:
	result = usb_submit_urb(urb, GFP_ATOMIC);
	if (result) {
		dev_err(&urb->dev->dev,
			"%s - Error %d submitting interrupt urb\n",
			__func__, result);
	}
}

static int mos7840_port_paranoia_check(struct usb_serial_port *port,
				       const char *function)
{
	if (!port) {
		dbg("%s - port == NULL", function);
		return -1;
	}
	if (!port->serial) {
		dbg("%s - port->serial == NULL", function);
		return -1;
	}

	return 0;
}

/* Inline functions to check the sanity of a pointer that is passed to us */
static int mos7840_serial_paranoia_check(struct usb_serial *serial,
					 const char *function)
{
	if (!serial) {
		dbg("%s - serial == NULL", function);
		return -1;
	}
	if (!serial->type) {
		dbg("%s - serial->type == NULL!", function);
		return -1;
	}

	return 0;
}

static struct usb_serial *mos7840_get_usb_serial(struct usb_serial_port *port,
						 const char *function)
{
	/* if no port was specified, or it fails a paranoia check */
	if (!port ||
	    mos7840_port_paranoia_check(port, function) ||
	    mos7840_serial_paranoia_check(port->serial, function)) {
		/* then say that we don't have a valid usb_serial thing,
		 * which will end up genrating -ENODEV return values */
		return NULL;
	}

	return port->serial;
}

/*****************************************************************************
 * mos7840_bulk_in_callback
 *	this is the callback function for when we have received data on the
 *	bulk in endpoint.
 *****************************************************************************/

static void mos7840_bulk_in_callback(struct urb *urb)
{
	int retval;
	unsigned char *data;
	struct usb_serial *serial;
	struct usb_serial_port *port;
	struct moschip_port *mos7840_port;
	struct tty_struct *tty;
	int status = urb->status;

	mos7840_port = urb->context;
	if (!mos7840_port) {
		dbg("%s", "NULL mos7840_port pointer");
		return;
	}

	if (status) {
		dbg("nonzero read bulk status received: %d", status);
		mos7840_port->read_urb_busy = false;
		return;
	}

	port = (struct usb_serial_port *)mos7840_port->port;
	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Port Paranoia failed");
		mos7840_port->read_urb_busy = false;
		return;
	}

	serial = mos7840_get_usb_serial(port, __func__);
	if (!serial) {
		dbg("%s", "Bad serial pointer");
		mos7840_port->read_urb_busy = false;
		return;
	}

	dbg("%s", "Entering... ");

	data = urb->transfer_buffer;

	dbg("%s", "Entering ...........");

	if (urb->actual_length) {
		tty = tty_port_tty_get(&mos7840_port->port->port);
		if (tty) {
			tty_insert_flip_string(tty, data, urb->actual_length);
			dbg(" %s ", data);
			tty_flip_buffer_push(tty);
			tty_kref_put(tty);
		}
		mos7840_port->icount.rx += urb->actual_length;
		smp_wmb();
		dbg("mos7840_port->icount.rx is %d:",
		    mos7840_port->icount.rx);
	}

	if (!mos7840_port->read_urb) {
		dbg("%s", "URB KILLED !!!");
		mos7840_port->read_urb_busy = false;
		return;
	}


	mos7840_port->read_urb_busy = true;
	retval = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC);

	if (retval) {
		dbg("usb_submit_urb(read bulk) failed, retval = %d", retval);
		mos7840_port->read_urb_busy = false;
	}
}

/*****************************************************************************
 * mos7840_bulk_out_data_callback
 *	this is the callback function for when we have finished sending
 *	serial data on the bulk out endpoint.
 *****************************************************************************/

static void mos7840_bulk_out_data_callback(struct urb *urb)
{
	struct moschip_port *mos7840_port;
	struct tty_struct *tty;
	int status = urb->status;
	int i;

	mos7840_port = urb->context;
	spin_lock(&mos7840_port->pool_lock);
	for (i = 0; i < NUM_URBS; i++) {
		if (urb == mos7840_port->write_urb_pool[i]) {
			mos7840_port->busy[i] = 0;
			break;
		}
	}
	spin_unlock(&mos7840_port->pool_lock);

	if (status) {
		dbg("nonzero write bulk status received:%d", status);
		return;
	}

	if (mos7840_port_paranoia_check(mos7840_port->port, __func__)) {
		dbg("%s", "Port Paranoia failed");
		return;
	}

	dbg("%s", "Entering .........");

	tty = tty_port_tty_get(&mos7840_port->port->port);
	if (tty && mos7840_port->open)
		tty_wakeup(tty);
	tty_kref_put(tty);

}

/************************************************************************/
/*       D R I V E R  T T Y  I N T E R F A C E  F U N C T I O N S       */
/************************************************************************/
#ifdef MCSSerialProbe
static int mos7840_serial_probe(struct usb_serial *serial,
				const struct usb_device_id *id)
{

	/*need to implement the mode_reg reading and updating\
	   structures usb_serial_ device_type\
	   (i.e num_ports, num_bulkin,bulkout etc) */
	/* Also we can update the changes  attach */
	return 1;
}
#endif

/*****************************************************************************
 * mos7840_open
 *	this function is called by the tty driver when a port is opened
 *	If successful, we return 0
 *	Otherwise we return a negative error number.
 *****************************************************************************/

static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
{
	int response;
	int j;
	struct usb_serial *serial;
	struct urb *urb;
	__u16 Data;
	int status;
	struct moschip_port *mos7840_port;
	struct moschip_port *port0;

	dbg ("%s enter", __func__);

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Port Paranoia failed");
		return -ENODEV;
	}

	serial = port->serial;

	if (mos7840_serial_paranoia_check(serial, __func__)) {
		dbg("%s", "Serial Paranoia failed");
		return -ENODEV;
	}

	mos7840_port = mos7840_get_port_private(port);
	port0 = mos7840_get_port_private(serial->port[0]);

	if (mos7840_port == NULL || port0 == NULL)
		return -ENODEV;

	usb_clear_halt(serial->dev, port->write_urb->pipe);
	usb_clear_halt(serial->dev, port->read_urb->pipe);
	port0->open_ports++;

	/* Initialising the write urb pool */
	for (j = 0; j < NUM_URBS; ++j) {
		urb = usb_alloc_urb(0, GFP_KERNEL);
		mos7840_port->write_urb_pool[j] = urb;

		if (urb == NULL) {
			dev_err(&port->dev, "No more urbs???\n");
			continue;
		}

		urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE,
								GFP_KERNEL);
		if (!urb->transfer_buffer) {
			usb_free_urb(urb);
			mos7840_port->write_urb_pool[j] = NULL;
			dev_err(&port->dev,
				"%s-out of memory for urb buffers.\n",
				__func__);
			continue;
		}
	}

/*****************************************************************************
 * Initialize MCS7840 -- Write Init values to corresponding Registers
 *
 * Register Index
 * 1 : IER
 * 2 : FCR
 * 3 : LCR
 * 4 : MCR
 *
 * 0x08 : SP1/2 Control Reg
 *****************************************************************************/

	/* NEED to check the following Block */

	Data = 0x0;
	status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data);
	if (status < 0) {
		dbg("Reading Spreg failed");
		return -1;
	}
	Data |= 0x80;
	status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
	if (status < 0) {
		dbg("writing Spreg failed");
		return -1;
	}

	Data &= ~0x80;
	status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
	if (status < 0) {
		dbg("writing Spreg failed");
		return -1;
	}
	/* End of block to be checked */

	Data = 0x0;
	status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
									&Data);
	if (status < 0) {
		dbg("Reading Controlreg failed");
		return -1;
	}
	Data |= 0x08;		/* Driver done bit */
	Data |= 0x20;		/* rx_disable */
	status = mos7840_set_reg_sync(port,
				mos7840_port->ControlRegOffset, Data);
	if (status < 0) {
		dbg("writing Controlreg failed");
		return -1;
	}
	/* do register settings here */
	/* Set all regs to the device default values. */
	/***********************************
	 * First Disable all interrupts.
	 ***********************************/
	Data = 0x00;
	status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
	if (status < 0) {
		dbg("disabling interrupts failed");
		return -1;
	}
	/* Set FIFO_CONTROL_REGISTER to the default value */
	Data = 0x00;
	status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
	if (status < 0) {
		dbg("Writing FIFO_CONTROL_REGISTER  failed");
		return -1;
	}

	Data = 0xcf;
	status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
	if (status < 0) {
		dbg("Writing FIFO_CONTROL_REGISTER  failed");
		return -1;
	}

	Data = 0x03;
	status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
	mos7840_port->shadowLCR = Data;

	Data = 0x0b;
	status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
	mos7840_port->shadowMCR = Data;

	Data = 0x00;
	status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
	mos7840_port->shadowLCR = Data;

	Data |= SERIAL_LCR_DLAB;	/* data latch enable in LCR 0x80 */
	status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);

	Data = 0x0c;
	status = mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data);

	Data = 0x0;
	status = mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data);

	Data = 0x00;
	status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);

	Data = Data & ~SERIAL_LCR_DLAB;
	status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
	mos7840_port->shadowLCR = Data;

	/* clearing Bulkin and Bulkout Fifo */
	Data = 0x0;
	status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data);

	Data = Data | 0x0c;
	status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);

	Data = Data & ~0x0c;
	status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
	/* Finally enable all interrupts */
	Data = 0x0c;
	status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);

	/* clearing rx_disable */
	Data = 0x0;
	status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
									&Data);
	Data = Data & ~0x20;
	status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset,
									Data);

	/* rx_negate */
	Data = 0x0;
	status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
									&Data);
	Data = Data | 0x10;
	status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset,
									Data);

	/* Check to see if we've set up our endpoint info yet    *
	 * (can't set it up in mos7840_startup as the structures *
	 * were not set up at that time.)                        */
	if (port0->open_ports == 1) {
		if (serial->port[0]->interrupt_in_buffer == NULL) {
			/* set up interrupt urb */
			usb_fill_int_urb(serial->port[0]->interrupt_in_urb,
				serial->dev,
				usb_rcvintpipe(serial->dev,
				serial->port[0]->interrupt_in_endpointAddress),
				serial->port[0]->interrupt_in_buffer,
				serial->port[0]->interrupt_in_urb->
				transfer_buffer_length,
				mos7840_interrupt_callback,
				serial,
				serial->port[0]->interrupt_in_urb->interval);

			/* start interrupt read for mos7840               *
			 * will continue as long as mos7840 is connected  */

			response =
			    usb_submit_urb(serial->port[0]->interrupt_in_urb,
					   GFP_KERNEL);
			if (response) {
				dev_err(&port->dev, "%s - Error %d submitting "
					"interrupt urb\n", __func__, response);
			}

		}

	}

	/* see if we've set up our endpoint info yet   *
	 * (can't set it up in mos7840_startup as the  *
	 * structures were not set up at that time.)   */

	dbg("port number is %d", port->number);
	dbg("serial number is %d", port->serial->minor);
	dbg("Bulkin endpoint is %d", port->bulk_in_endpointAddress);
	dbg("BulkOut endpoint is %d", port->bulk_out_endpointAddress);
	dbg("Interrupt endpoint is %d", port->interrupt_in_endpointAddress);
	dbg("port's number in the device is %d", mos7840_port->port_num);
	mos7840_port->read_urb = port->read_urb;

	/* set up our bulk in urb */
	if ((serial->num_ports == 2)
		&& ((((__u16)port->number -
			(__u16)(port->serial->minor)) % 2) != 0)) {
		usb_fill_bulk_urb(mos7840_port->read_urb,
			serial->dev,
			usb_rcvbulkpipe(serial->dev,
				(port->bulk_in_endpointAddress) + 2),
			port->bulk_in_buffer,
			mos7840_port->read_urb->transfer_buffer_length,
			mos7840_bulk_in_callback, mos7840_port);
	} else {
		usb_fill_bulk_urb(mos7840_port->read_urb,
			serial->dev,
			usb_rcvbulkpipe(serial->dev,
				port->bulk_in_endpointAddress),
			port->bulk_in_buffer,
			mos7840_port->read_urb->transfer_buffer_length,
			mos7840_bulk_in_callback, mos7840_port);
	}

	dbg("mos7840_open: bulkin endpoint is %d",
	    port->bulk_in_endpointAddress);
	mos7840_port->read_urb_busy = true;
	response = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL);
	if (response) {
		dev_err(&port->dev, "%s - Error %d submitting control urb\n",
			__func__, response);
		mos7840_port->read_urb_busy = false;
	}

	/* initialize our wait queues */
	init_waitqueue_head(&mos7840_port->wait_chase);
	init_waitqueue_head(&mos7840_port->delta_msr_wait);

	/* initialize our icount structure */
	memset(&(mos7840_port->icount), 0x00, sizeof(mos7840_port->icount));

	/* initialize our port settings */
	/* Must set to enable ints! */
	mos7840_port->shadowMCR = MCR_MASTER_IE;
	/* send a open port command */
	mos7840_port->open = 1;
	/* mos7840_change_port_settings(mos7840_port,old_termios); */
	mos7840_port->icount.tx = 0;
	mos7840_port->icount.rx = 0;

	dbg("usb_serial serial:%p       mos7840_port:%p\n      usb_serial_port port:%p",
				serial, mos7840_port, port);

	dbg ("%s leave", __func__);

	return 0;

}

/*****************************************************************************
 * mos7840_chars_in_buffer
 *	this function is called by the tty driver when it wants to know how many
 *	bytes of data we currently have outstanding in the port (data that has
 *	been written, but hasn't made it out the port yet)
 *	If successful, we return the number of bytes left to be written in the
 *	system,
 *	Otherwise we return zero.
 *****************************************************************************/

static int mos7840_chars_in_buffer(struct tty_struct *tty)
{
	struct usb_serial_port *port = tty->driver_data;
	int i;
	int chars = 0;
	unsigned long flags;
	struct moschip_port *mos7840_port;

	dbg("%s", " mos7840_chars_in_buffer:entering ...........");

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Invalid port");
		return 0;
	}

	mos7840_port = mos7840_get_port_private(port);
	if (mos7840_port == NULL) {
		dbg("%s", "mos7840_break:leaving ...........");
		return 0;
	}

	spin_lock_irqsave(&mos7840_port->pool_lock, flags);
	for (i = 0; i < NUM_URBS; ++i)
		if (mos7840_port->busy[i])
			chars += URB_TRANSFER_BUFFER_SIZE;
	spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
	dbg("%s - returns %d", __func__, chars);
	return chars;

}

/*****************************************************************************
 * mos7840_close
 *	this function is called by the tty driver when a port is closed
 *****************************************************************************/

static void mos7840_close(struct usb_serial_port *port)
{
	struct usb_serial *serial;
	struct moschip_port *mos7840_port;
	struct moschip_port *port0;
	int j;
	__u16 Data;

	dbg("%s", "mos7840_close:entering...");

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Port Paranoia failed");
		return;
	}

	serial = mos7840_get_usb_serial(port, __func__);
	if (!serial) {
		dbg("%s", "Serial Paranoia failed");
		return;
	}

	mos7840_port = mos7840_get_port_private(port);
	port0 = mos7840_get_port_private(serial->port[0]);

	if (mos7840_port == NULL || port0 == NULL)
		return;

	for (j = 0; j < NUM_URBS; ++j)
		usb_kill_urb(mos7840_port->write_urb_pool[j]);

	/* Freeing Write URBs */
	for (j = 0; j < NUM_URBS; ++j) {
		if (mos7840_port->write_urb_pool[j]) {
			if (mos7840_port->write_urb_pool[j]->transfer_buffer)
				kfree(mos7840_port->write_urb_pool[j]->
				      transfer_buffer);

			usb_free_urb(mos7840_port->write_urb_pool[j]);
		}
	}

	/* While closing port, shutdown all bulk read, write  *
	 * and interrupt read if they exists                  */
	if (serial->dev) {
		if (mos7840_port->write_urb) {
			dbg("%s", "Shutdown bulk write");
			usb_kill_urb(mos7840_port->write_urb);
		}
		if (mos7840_port->read_urb) {
			dbg("%s", "Shutdown bulk read");
			usb_kill_urb(mos7840_port->read_urb);
			mos7840_port->read_urb_busy = false;
		}
		if ((&mos7840_port->control_urb)) {
			dbg("%s", "Shutdown control read");
			/*/      usb_kill_urb (mos7840_port->control_urb); */
		}
	}
/*      if(mos7840_port->ctrl_buf != NULL) */
/*              kfree(mos7840_port->ctrl_buf); */
	port0->open_ports--;
	dbg("mos7840_num_open_ports in close%d:in port%d",
	    port0->open_ports, port->number);
	if (port0->open_ports == 0) {
		if (serial->port[0]->interrupt_in_urb) {
			dbg("%s", "Shutdown interrupt_in_urb");
			usb_kill_urb(serial->port[0]->interrupt_in_urb);
		}
	}

	if (mos7840_port->write_urb) {
		/* if this urb had a transfer buffer already (old tx) free it */
		if (mos7840_port->write_urb->transfer_buffer != NULL)
			kfree(mos7840_port->write_urb->transfer_buffer);
		usb_free_urb(mos7840_port->write_urb);
	}

	Data = 0x0;
	mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);

	Data = 0x00;
	mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);

	mos7840_port->open = 0;

	dbg("%s", "Leaving ............");
}

/************************************************************************
 *
 * mos7840_block_until_chase_response
 *
 *	This function will block the close until one of the following:
 *		1. Response to our Chase comes from mos7840
 *		2. A timeout of 10 seconds without activity has expired
 *		   (1K of mos7840 data @ 2400 baud ==> 4 sec to empty)
 *
 ************************************************************************/

static void mos7840_block_until_chase_response(struct tty_struct *tty,
					struct moschip_port *mos7840_port)
{
	int timeout = 1 * HZ;
	int wait = 10;
	int count;

	while (1) {
		count = mos7840_chars_in_buffer(tty);

		/* Check for Buffer status */
		if (count <= 0)
			return;

		/* Block the thread for a while */
		interruptible_sleep_on_timeout(&mos7840_port->wait_chase,
					       timeout);
		/* No activity.. count down section */
		wait--;
		if (wait == 0) {
			dbg("%s - TIMEOUT", __func__);
			return;
		} else {
			/* Reset timeout value back to seconds */
			wait = 10;
		}
	}

}

/*****************************************************************************
 * mos7840_break
 *	this function sends a break to the port
 *****************************************************************************/
static void mos7840_break(struct tty_struct *tty, int break_state)
{
	struct usb_serial_port *port = tty->driver_data;
	unsigned char data;
	struct usb_serial *serial;
	struct moschip_port *mos7840_port;

	dbg("%s", "Entering ...........");
	dbg("mos7840_break: Start");

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Port Paranoia failed");
		return;
	}

	serial = mos7840_get_usb_serial(port, __func__);
	if (!serial) {
		dbg("%s", "Serial Paranoia failed");
		return;
	}

	mos7840_port = mos7840_get_port_private(port);

	if (mos7840_port == NULL)
		return;

	if (serial->dev)
		/* flush and block until tx is empty */
		mos7840_block_until_chase_response(tty, mos7840_port);

	if (break_state == -1)
		data = mos7840_port->shadowLCR | LCR_SET_BREAK;
	else
		data = mos7840_port->shadowLCR & ~LCR_SET_BREAK;

	/* FIXME: no locking on shadowLCR anywhere in driver */
	mos7840_port->shadowLCR = data;
	dbg("mcs7840_break mos7840_port->shadowLCR is %x",
	    mos7840_port->shadowLCR);
	mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER,
			     mos7840_port->shadowLCR);
}

/*****************************************************************************
 * mos7840_write_room
 *	this function is called by the tty driver when it wants to know how many
 *	bytes of data we can accept for a specific port.
 *	If successful, we return the amount of room that we have for this port
 *	Otherwise we return a negative error number.
 *****************************************************************************/

static int mos7840_write_room(struct tty_struct *tty)
{
	struct usb_serial_port *port = tty->driver_data;
	int i;
	int room = 0;
	unsigned long flags;
	struct moschip_port *mos7840_port;

	dbg("%s", " mos7840_write_room:entering ...........");

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Invalid port");
		dbg("%s", " mos7840_write_room:leaving ...........");
		return -1;
	}

	mos7840_port = mos7840_get_port_private(port);
	if (mos7840_port == NULL) {
		dbg("%s", "mos7840_break:leaving ...........");
		return -1;
	}

	spin_lock_irqsave(&mos7840_port->pool_lock, flags);
	for (i = 0; i < NUM_URBS; ++i) {
		if (!mos7840_port->busy[i])
			room += URB_TRANSFER_BUFFER_SIZE;
	}
	spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);

	room = (room == 0) ? 0 : room - URB_TRANSFER_BUFFER_SIZE + 1;
	dbg("%s - returns %d", __func__, room);
	return room;

}

/*****************************************************************************
 * mos7840_write
 *	this function is called by the tty driver when data should be written to
 *	the port.
 *	If successful, we return the number of bytes written, otherwise we
 *      return a negative error number.
 *****************************************************************************/

static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
			 const unsigned char *data, int count)
{
	int status;
	int i;
	int bytes_sent = 0;
	int transfer_size;
	unsigned long flags;

	struct moschip_port *mos7840_port;
	struct usb_serial *serial;
	struct urb *urb;
	/* __u16 Data; */
	const unsigned char *current_position = data;
	unsigned char *data1;
	dbg("%s", "entering ...........");
	/* dbg("mos7840_write: mos7840_port->shadowLCR is %x",
					mos7840_port->shadowLCR); */

#ifdef NOTMOS7840
	Data = 0x00;
	status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
	mos7840_port->shadowLCR = Data;
	dbg("mos7840_write: LINE_CONTROL_REGISTER is %x", Data);
	dbg("mos7840_write: mos7840_port->shadowLCR is %x",
	    mos7840_port->shadowLCR);

	/* Data = 0x03; */
	/* status = mos7840_set_uart_reg(port,LINE_CONTROL_REGISTER,Data); */
	/* mos7840_port->shadowLCR=Data;//Need to add later */

	Data |= SERIAL_LCR_DLAB;	/* data latch enable in LCR 0x80 */
	status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);

	/* Data = 0x0c; */
	/* status = mos7840_set_uart_reg(port,DIVISOR_LATCH_LSB,Data); */
	Data = 0x00;
	status = mos7840_get_uart_reg(port, DIVISOR_LATCH_LSB, &Data);
	dbg("mos7840_write:DLL value is %x", Data);

	Data = 0x0;
	status = mos7840_get_uart_reg(port, DIVISOR_LATCH_MSB, &Data);
	dbg("mos7840_write:DLM value is %x", Data);

	Data = Data & ~SERIAL_LCR_DLAB;
	dbg("mos7840_write: mos7840_port->shadowLCR is %x",
	    mos7840_port->shadowLCR);
	status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
#endif

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Port Paranoia failed");
		return -1;
	}

	serial = port->serial;
	if (mos7840_serial_paranoia_check(serial, __func__)) {
		dbg("%s", "Serial Paranoia failed");
		return -1;
	}

	mos7840_port = mos7840_get_port_private(port);
	if (mos7840_port == NULL) {
		dbg("%s", "mos7840_port is NULL");
		return -1;
	}

	/* try to find a free urb in the list */
	urb = NULL;

	spin_lock_irqsave(&mos7840_port->pool_lock, flags);
	for (i = 0; i < NUM_URBS; ++i) {
		if (!mos7840_port->busy[i]) {
			mos7840_port->busy[i] = 1;
			urb = mos7840_port->write_urb_pool[i];
			dbg("URB:%d", i);
			break;
		}
	}
	spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);

	if (urb == NULL) {
		dbg("%s - no more free urbs", __func__);
		goto exit;
	}

	if (urb->transfer_buffer == NULL) {
		urb->transfer_buffer =
		    kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL);

		if (urb->transfer_buffer == NULL) {
			dev_err_console(port, "%s no more kernel memory...\n",
				__func__);
			goto exit;
		}
	}
	transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE);

	memcpy(urb->transfer_buffer, current_position, transfer_size);

	/* fill urb with data and submit  */
	if ((serial->num_ports == 2)
		&& ((((__u16)port->number -
			(__u16)(port->serial->minor)) % 2) != 0)) {
		usb_fill_bulk_urb(urb,
			serial->dev,
			usb_sndbulkpipe(serial->dev,
				(port->bulk_out_endpointAddress) + 2),
			urb->transfer_buffer,
			transfer_size,
			mos7840_bulk_out_data_callback, mos7840_port);
	} else {
		usb_fill_bulk_urb(urb,
			serial->dev,
			usb_sndbulkpipe(serial->dev,
				port->bulk_out_endpointAddress),
			urb->transfer_buffer,
			transfer_size,
			mos7840_bulk_out_data_callback, mos7840_port);
	}

	data1 = urb->transfer_buffer;
	dbg("bulkout endpoint is %d", port->bulk_out_endpointAddress);

	/* send it down the pipe */
	status = usb_submit_urb(urb, GFP_ATOMIC);

	if (status) {
		mos7840_port->busy[i] = 0;
		dev_err_console(port, "%s - usb_submit_urb(write bulk) failed "
			"with status = %d\n", __func__, status);
		bytes_sent = status;
		goto exit;
	}
	bytes_sent = transfer_size;
	mos7840_port->icount.tx += transfer_size;
	smp_wmb();
	dbg("mos7840_port->icount.tx is %d:", mos7840_port->icount.tx);
exit:
	return bytes_sent;

}

/*****************************************************************************
 * mos7840_throttle
 *	this function is called by the tty driver when it wants to stop the data
 *	being read from the port.
 *****************************************************************************/

static void mos7840_throttle(struct tty_struct *tty)
{
	struct usb_serial_port *port = tty->driver_data;
	struct moschip_port *mos7840_port;
	int status;

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Invalid port");
		return;
	}

	dbg("- port %d", port->number);

	mos7840_port = mos7840_get_port_private(port);

	if (mos7840_port == NULL)
		return;

	if (!mos7840_port->open) {
		dbg("%s", "port not opened");
		return;
	}

	dbg("%s", "Entering ..........");

	/* if we are implementing XON/XOFF, send the stop character */
	if (I_IXOFF(tty)) {
		unsigned char stop_char = STOP_CHAR(tty);
		status = mos7840_write(tty, port, &stop_char, 1);
		if (status <= 0)
			return;
	}
	/* if we are implementing RTS/CTS, toggle that line */
	if (tty->termios->c_cflag & CRTSCTS) {
		mos7840_port->shadowMCR &= ~MCR_RTS;
		status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
					 mos7840_port->shadowMCR);
		if (status < 0)
			return;
	}
}

/*****************************************************************************
 * mos7840_unthrottle
 *	this function is called by the tty driver when it wants to resume
 *	the data being read from the port (called after mos7840_throttle is
 *	called)
 *****************************************************************************/
static void mos7840_unthrottle(struct tty_struct *tty)
{
	struct usb_serial_port *port = tty->driver_data;
	int status;
	struct moschip_port *mos7840_port = mos7840_get_port_private(port);

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Invalid port");
		return;
	}

	if (mos7840_port == NULL)
		return;

	if (!mos7840_port->open) {
		dbg("%s - port not opened", __func__);
		return;
	}

	dbg("%s", "Entering ..........");

	/* if we are implementing XON/XOFF, send the start character */
	if (I_IXOFF(tty)) {
		unsigned char start_char = START_CHAR(tty);
		status = mos7840_write(tty, port, &start_char, 1);
		if (status <= 0)
			return;
	}

	/* if we are implementing RTS/CTS, toggle that line */
	if (tty->termios->c_cflag & CRTSCTS) {
		mos7840_port->shadowMCR |= MCR_RTS;
		status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
					 mos7840_port->shadowMCR);
		if (status < 0)
			return;
	}
}

static int mos7840_tiocmget(struct tty_struct *tty)
{
	struct usb_serial_port *port = tty->driver_data;
	struct moschip_port *mos7840_port;
	unsigned int result;
	__u16 msr;
	__u16 mcr;
	int status;
	mos7840_port = mos7840_get_port_private(port);

	dbg("%s - port %d", __func__, port->number);

	if (mos7840_port == NULL)
		return -ENODEV;

	status = mos7840_get_uart_reg(port, MODEM_STATUS_REGISTER, &msr);
	status = mos7840_get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr);
	result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0)
	    | ((mcr & MCR_RTS) ? TIOCM_RTS : 0)
	    | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0)
	    | ((msr & MOS7840_MSR_CTS) ? TIOCM_CTS : 0)
	    | ((msr & MOS7840_MSR_CD) ? TIOCM_CAR : 0)
	    | ((msr & MOS7840_MSR_RI) ? TIOCM_RI : 0)
	    | ((msr & MOS7840_MSR_DSR) ? TIOCM_DSR : 0);

	dbg("%s - 0x%04X", __func__, result);

	return result;
}

static int mos7840_tiocmset(struct tty_struct *tty,
			    unsigned int set, unsigned int clear)
{
	struct usb_serial_port *port = tty->driver_data;
	struct moschip_port *mos7840_port;
	unsigned int mcr;
	int status;

	dbg("%s - port %d", __func__, port->number);

	mos7840_port = mos7840_get_port_private(port);

	if (mos7840_port == NULL)
		return -ENODEV;

	/* FIXME: What locks the port registers ? */
	mcr = mos7840_port->shadowMCR;
	if (clear & TIOCM_RTS)
		mcr &= ~MCR_RTS;
	if (clear & TIOCM_DTR)
		mcr &= ~MCR_DTR;
	if (clear & TIOCM_LOOP)
		mcr &= ~MCR_LOOPBACK;

	if (set & TIOCM_RTS)
		mcr |= MCR_RTS;
	if (set & TIOCM_DTR)
		mcr |= MCR_DTR;
	if (set & TIOCM_LOOP)
		mcr |= MCR_LOOPBACK;

	mos7840_port->shadowMCR = mcr;

	status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr);
	if (status < 0) {
		dbg("setting MODEM_CONTROL_REGISTER Failed");
		return status;
	}

	return 0;
}

/*****************************************************************************
 * mos7840_calc_baud_rate_divisor
 *	this function calculates the proper baud rate divisor for the specified
 *	baud rate.
 *****************************************************************************/
static int mos7840_calc_baud_rate_divisor(int baudRate, int *divisor,
					  __u16 *clk_sel_val)
{

	dbg("%s - %d", __func__, baudRate);

	if (baudRate <= 115200) {
		*divisor = 115200 / baudRate;
		*clk_sel_val = 0x0;
	}
	if ((baudRate > 115200) && (baudRate <= 230400)) {
		*divisor = 230400 / baudRate;
		*clk_sel_val = 0x10;
	} else if ((baudRate > 230400) && (baudRate <= 403200)) {
		*divisor = 403200 / baudRate;
		*clk_sel_val = 0x20;
	} else if ((baudRate > 403200) && (baudRate <= 460800)) {
		*divisor = 460800 / baudRate;
		*clk_sel_val = 0x30;
	} else if ((baudRate > 460800) && (baudRate <= 806400)) {
		*divisor = 806400 / baudRate;
		*clk_sel_val = 0x40;
	} else if ((baudRate > 806400) && (baudRate <= 921600)) {
		*divisor = 921600 / baudRate;
		*clk_sel_val = 0x50;
	} else if ((baudRate > 921600) && (baudRate <= 1572864)) {
		*divisor = 1572864 / baudRate;
		*clk_sel_val = 0x60;
	} else if ((baudRate > 1572864) && (baudRate <= 3145728)) {
		*divisor = 3145728 / baudRate;
		*clk_sel_val = 0x70;
	}
	return 0;

#ifdef NOTMCS7840

	for (i = 0; i < ARRAY_SIZE(mos7840_divisor_table); i++) {
		if (mos7840_divisor_table[i].BaudRate == baudrate) {
			*divisor = mos7840_divisor_table[i].Divisor;
			return 0;
		}
	}

	/* After trying for all the standard baud rates    *
	 * Try calculating the divisor for this baud rate  */

	if (baudrate > 75 && baudrate < 230400) {
		/* get the divisor */
		custom = (__u16) (230400L / baudrate);

		/* Check for round off */
		round1 = (__u16) (2304000L / baudrate);
		round = (__u16) (round1 - (custom * 10));
		if (round > 4)
			custom++;
		*divisor = custom;

		dbg(" Baud %d = %d", baudrate, custom);
		return 0;
	}

	dbg("%s", " Baud calculation Failed...");
	return -1;
#endif
}

/*****************************************************************************
 * mos7840_send_cmd_write_baud_rate
 *	this function sends the proper command to change the baud rate of the
 *	specified port.
 *****************************************************************************/

static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port,
					    int baudRate)
{
	int divisor = 0;
	int status;
	__u16 Data;
	unsigned char number;
	__u16 clk_sel_val;
	struct usb_serial_port *port;

	if (mos7840_port == NULL)
		return -1;

	port = (struct usb_serial_port *)mos7840_port->port;
	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Invalid port");
		return -1;
	}

	if (mos7840_serial_paranoia_check(port->serial, __func__)) {
		dbg("%s", "Invalid Serial");
		return -1;
	}

	dbg("%s", "Entering ..........");

	number = mos7840_port->port->number - mos7840_port->port->serial->minor;

	dbg("%s - port = %d, baud = %d", __func__,
	    mos7840_port->port->number, baudRate);
	/* reset clk_uart_sel in spregOffset */
	if (baudRate > 115200) {
#ifdef HW_flow_control
		/* NOTE: need to see the pther register to modify */
		/* setting h/w flow control bit to 1 */
		Data = 0x2b;
		mos7840_port->shadowMCR = Data;
		status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
									Data);
		if (status < 0) {
			dbg("Writing spreg failed in set_serial_baud");
			return -1;
		}
#endif

	} else {
#ifdef HW_flow_control
		/* setting h/w flow control bit to 0 */
		Data = 0xb;
		mos7840_port->shadowMCR = Data;
		status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
									Data);
		if (status < 0) {
			dbg("Writing spreg failed in set_serial_baud");
			return -1;
		}
#endif

	}

	if (1) {		/* baudRate <= 115200) */
		clk_sel_val = 0x0;
		Data = 0x0;
		status = mos7840_calc_baud_rate_divisor(baudRate, &divisor,
						   &clk_sel_val);
		status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset,
								 &Data);
		if (status < 0) {
			dbg("reading spreg failed in set_serial_baud");
			return -1;
		}
		Data = (Data & 0x8f) | clk_sel_val;
		status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset,
								Data);
		if (status < 0) {
			dbg("Writing spreg failed in set_serial_baud");
			return -1;
		}
		/* Calculate the Divisor */

		if (status) {
			dev_err(&port->dev, "%s - bad baud rate\n", __func__);
			return status;
		}
		/* Enable access to divisor latch */
		Data = mos7840_port->shadowLCR | SERIAL_LCR_DLAB;
		mos7840_port->shadowLCR = Data;
		mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);

		/* Write the divisor */
		Data = (unsigned char)(divisor & 0xff);
		dbg("set_serial_baud Value to write DLL is %x", Data);
		mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data);

		Data = (unsigned char)((divisor & 0xff00) >> 8);
		dbg("set_serial_baud Value to write DLM is %x", Data);
		mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data);

		/* Disable access to divisor latch */
		Data = mos7840_port->shadowLCR & ~SERIAL_LCR_DLAB;
		mos7840_port->shadowLCR = Data;
		mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);

	}
	return status;
}

/*****************************************************************************
 * mos7840_change_port_settings
 *	This routine is called to set the UART on the device to match
 *      the specified new settings.
 *****************************************************************************/

static void mos7840_change_port_settings(struct tty_struct *tty,
	struct moschip_port *mos7840_port, struct ktermios *old_termios)
{
	int baud;
	unsigned cflag;
	unsigned iflag;
	__u8 lData;
	__u8 lParity;
	__u8 lStop;
	int status;
	__u16 Data;
	struct usb_serial_port *port;
	struct usb_serial *serial;

	if (mos7840_port == NULL)
		return;

	port = (struct usb_serial_port *)mos7840_port->port;

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Invalid port");
		return;
	}

	if (mos7840_serial_paranoia_check(port->serial, __func__)) {
		dbg("%s", "Invalid Serial");
		return;
	}

	serial = port->serial;

	dbg("%s - port %d", __func__, mos7840_port->port->number);

	if (!mos7840_port->open) {
		dbg("%s - port not opened", __func__);
		return;
	}

	dbg("%s", "Entering ..........");

	lData = LCR_BITS_8;
	lStop = LCR_STOP_1;
	lParity = LCR_PAR_NONE;

	cflag = tty->termios->c_cflag;
	iflag = tty->termios->c_iflag;

	/* Change the number of bits */
	if (cflag & CSIZE) {
		switch (cflag & CSIZE) {
		case CS5:
			lData = LCR_BITS_5;
			break;

		case CS6:
			lData = LCR_BITS_6;
			break;

		case CS7:
			lData = LCR_BITS_7;
			break;
		default:
		case CS8:
			lData = LCR_BITS_8;
			break;
		}
	}
	/* Change the Parity bit */
	if (cflag & PARENB) {
		if (cflag & PARODD) {
			lParity = LCR_PAR_ODD;
			dbg("%s - parity = odd", __func__);
		} else {
			lParity = LCR_PAR_EVEN;
			dbg("%s - parity = even", __func__);
		}

	} else {
		dbg("%s - parity = none", __func__);
	}

	if (cflag & CMSPAR)
		lParity = lParity | 0x20;

	/* Change the Stop bit */
	if (cflag & CSTOPB) {
		lStop = LCR_STOP_2;
		dbg("%s - stop bits = 2", __func__);
	} else {
		lStop = LCR_STOP_1;
		dbg("%s - stop bits = 1", __func__);
	}

	/* Update the LCR with the correct value */
	mos7840_port->shadowLCR &=
	    ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
	mos7840_port->shadowLCR |= (lData | lParity | lStop);

	dbg("mos7840_change_port_settings mos7840_port->shadowLCR is %x",
	    mos7840_port->shadowLCR);
	/* Disable Interrupts */
	Data = 0x00;
	mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);

	Data = 0x00;
	mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);

	Data = 0xcf;
	mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);

	/* Send the updated LCR value to the mos7840 */
	Data = mos7840_port->shadowLCR;

	mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);

	Data = 0x00b;
	mos7840_port->shadowMCR = Data;
	mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
	Data = 0x00b;
	mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);

	/* set up the MCR register and send it to the mos7840 */

	mos7840_port->shadowMCR = MCR_MASTER_IE;
	if (cflag & CBAUD)
		mos7840_port->shadowMCR |= (MCR_DTR | MCR_RTS);

	if (cflag & CRTSCTS)
		mos7840_port->shadowMCR |= (MCR_XON_ANY);
	else
		mos7840_port->shadowMCR &= ~(MCR_XON_ANY);

	Data = mos7840_port->shadowMCR;
	mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);

	/* Determine divisor based on baud rate */
	baud = tty_get_baud_rate(tty);

	if (!baud) {
		/* pick a default, any default... */
		dbg("%s", "Picked default baud...");
		baud = 9600;
	}

	dbg("%s - baud rate = %d", __func__, baud);
	status = mos7840_send_cmd_write_baud_rate(mos7840_port, baud);

	/* Enable Interrupts */
	Data = 0x0c;
	mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);

	if (mos7840_port->read_urb_busy == false) {
		mos7840_port->read_urb_busy = true;
		status = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC);
		if (status) {
			dbg("usb_submit_urb(read bulk) failed, status = %d",
			    status);
			mos7840_port->read_urb_busy = false;
		}
	}
	wake_up(&mos7840_port->delta_msr_wait);
	mos7840_port->delta_msr_cond = 1;
	dbg("mos7840_change_port_settings mos7840_port->shadowLCR is End %x",
	    mos7840_port->shadowLCR);
}

/*****************************************************************************
 * mos7840_set_termios
 *	this function is called by the tty driver when it wants to change
 *	the termios structure
 *****************************************************************************/

static void mos7840_set_termios(struct tty_struct *tty,
				struct usb_serial_port *port,
				struct ktermios *old_termios)
{
	int status;
	unsigned int cflag;
	struct usb_serial *serial;
	struct moschip_port *mos7840_port;
	dbg("mos7840_set_termios: START");
	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Invalid port");
		return;
	}

	serial = port->serial;

	if (mos7840_serial_paranoia_check(serial, __func__)) {
		dbg("%s", "Invalid Serial");
		return;
	}

	mos7840_port = mos7840_get_port_private(port);

	if (mos7840_port == NULL)
		return;

	if (!mos7840_port->open) {
		dbg("%s - port not opened", __func__);
		return;
	}

	dbg("%s", "setting termios - ");

	cflag = tty->termios->c_cflag;

	dbg("%s - clfag %08x iflag %08x", __func__,
	    tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
	dbg("%s - old clfag %08x old iflag %08x", __func__,
	    old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
	dbg("%s - port %d", __func__, port->number);

	/* change the port settings to the new ones specified */

	mos7840_change_port_settings(tty, mos7840_port, old_termios);

	if (!mos7840_port->read_urb) {
		dbg("%s", "URB KILLED !!!!!");
		return;
	}

	if (mos7840_port->read_urb_busy == false) {
		mos7840_port->read_urb_busy = true;
		status = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC);
		if (status) {
			dbg("usb_submit_urb(read bulk) failed, status = %d",
			    status);
			mos7840_port->read_urb_busy = false;
		}
	}
}

/*****************************************************************************
 * mos7840_get_lsr_info - get line status register info
 *
 * Purpose: Let user call ioctl() to get info when the UART physically
 * 	    is emptied.  On bus types like RS485, the transmitter must
 * 	    release the bus after transmitting. This must be done when
 * 	    the transmit shift register is empty, not be done when the
 * 	    transmit holding register is empty.  This functionality
 * 	    allows an RS485 driver to be written in user space.
 *****************************************************************************/

static int mos7840_get_lsr_info(struct tty_struct *tty,
				unsigned int __user *value)
{
	int count;
	unsigned int result = 0;

	count = mos7840_chars_in_buffer(tty);
	if (count == 0) {
		dbg("%s -- Empty", __func__);
		result = TIOCSER_TEMT;
	}

	if (copy_to_user(value, &result, sizeof(int)))
		return -EFAULT;
	return 0;
}

/*****************************************************************************
 * mos7840_get_serial_info
 *      function to get information about serial port
 *****************************************************************************/

static int mos7840_get_serial_info(struct moschip_port *mos7840_port,
				   struct serial_struct __user *retinfo)
{
	struct serial_struct tmp;

	if (mos7840_port == NULL)
		return -1;

	if (!retinfo)
		return -EFAULT;

	memset(&tmp, 0, sizeof(tmp));

	tmp.type = PORT_16550A;
	tmp.line = mos7840_port->port->serial->minor;
	tmp.port = mos7840_port->port->number;
	tmp.irq = 0;
	tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
	tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE;
	tmp.baud_base = 9600;
	tmp.close_delay = 5 * HZ;
	tmp.closing_wait = 30 * HZ;

	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
		return -EFAULT;
	return 0;
}

static int mos7840_get_icount(struct tty_struct *tty,
			struct serial_icounter_struct *icount)
{
	struct usb_serial_port *port = tty->driver_data;
	struct moschip_port *mos7840_port;
	struct async_icount cnow;

	mos7840_port = mos7840_get_port_private(port);
	cnow = mos7840_port->icount;

	smp_rmb();
	icount->cts = cnow.cts;
	icount->dsr = cnow.dsr;
	icount->rng = cnow.rng;
	icount->dcd = cnow.dcd;
	icount->rx = cnow.rx;
	icount->tx = cnow.tx;
	icount->frame = cnow.frame;
	icount->overrun = cnow.overrun;
	icount->parity = cnow.parity;
	icount->brk = cnow.brk;
	icount->buf_overrun = cnow.buf_overrun;

	dbg("%s (%d) TIOCGICOUNT RX=%d, TX=%d", __func__,
		port->number, icount->rx, icount->tx);
	return 0;
}

/*****************************************************************************
 * SerialIoctl
 *	this function handles any ioctl calls to the driver
 *****************************************************************************/

static int mos7840_ioctl(struct tty_struct *tty,
			 unsigned int cmd, unsigned long arg)
{
	struct usb_serial_port *port = tty->driver_data;
	void __user *argp = (void __user *)arg;
	struct moschip_port *mos7840_port;

	struct async_icount cnow;
	struct async_icount cprev;

	if (mos7840_port_paranoia_check(port, __func__)) {
		dbg("%s", "Invalid port");
		return -1;
	}

	mos7840_port = mos7840_get_port_private(port);

	if (mos7840_port == NULL)
		return -1;

	dbg("%s - port %d, cmd = 0x%x", __func__, port->number, cmd);

	switch (cmd) {
		/* return number of bytes available */

	case TIOCSERGETLSR:
		dbg("%s (%d) TIOCSERGETLSR", __func__, port->number);
		return mos7840_get_lsr_info(tty, argp);

	case TIOCGSERIAL:
		dbg("%s (%d) TIOCGSERIAL", __func__, port->number);
		return mos7840_get_serial_info(mos7840_port, argp);

	case TIOCSSERIAL:
		dbg("%s (%d) TIOCSSERIAL", __func__, port->number);
		break;

	case TIOCMIWAIT:
		dbg("%s (%d) TIOCMIWAIT", __func__, port->number);
		cprev = mos7840_port->icount;
		while (1) {
			/* interruptible_sleep_on(&mos7840_port->delta_msr_wait); */
			mos7840_port->delta_msr_cond = 0;
			wait_event_interruptible(mos7840_port->delta_msr_wait,
						 (mos7840_port->
						  delta_msr_cond == 1));

			/* see if a signal did it */
			if (signal_pending(current))
				return -ERESTARTSYS;
			cnow = mos7840_port->icount;
			smp_rmb();
			if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
			    cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
				return -EIO;	/* no change => error */
			if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
			    ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
			    ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) ||
			    ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) {
				return 0;
			}
			cprev = cnow;
		}
		/* NOTREACHED */
		break;

	default:
		break;
	}
	return -ENOIOCTLCMD;
}

static int mos7840_calc_num_ports(struct usb_serial *serial)
{
	__u16 Data = 0x00;
	int ret = 0;
	int mos7840_num_ports;

	ret = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
		MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, &Data,
		VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);

	if ((Data & 0x01) == 0) {
		mos7840_num_ports = 2;
		serial->num_bulk_in = 2;
		serial->num_bulk_out = 2;
		serial->num_ports = 2;
	} else {
		mos7840_num_ports = 4;
		serial->num_bulk_in = 4;
		serial->num_bulk_out = 4;
		serial->num_ports = 4;
	}

	return mos7840_num_ports;
}

/****************************************************************************
 * mos7840_startup
 ****************************************************************************/

static int mos7840_startup(struct usb_serial *serial)
{
	struct moschip_port *mos7840_port;
	struct usb_device *dev;
	int i, status;

	__u16 Data;
	dbg("%s", "mos7840_startup :Entering..........");

	if (!serial) {
		dbg("%s", "Invalid Handler");
		return -1;
	}

	dev = serial->dev;

	dbg("%s", "Entering...");
	dbg ("mos7840_startup: serial = %p", serial);

	/* we set up the pointers to the endpoints in the mos7840_open *
	 * function, as the structures aren't created yet.             */

	/* set up port private structures */
	for (i = 0; i < serial->num_ports; ++i) {
		dbg ("mos7840_startup: configuring port %d............", i);
		mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL);
		if (mos7840_port == NULL) {
			dev_err(&dev->dev, "%s - Out of memory\n", __func__);
			status = -ENOMEM;
			i--; /* don't follow NULL pointer cleaning up */
			goto error;
		}

		/* Initialize all port interrupt end point to port 0 int
		 * endpoint. Our device has only one interrupt end point
		 * common to all port */

		mos7840_port->port = serial->port[i];
		mos7840_set_port_private(serial->port[i], mos7840_port);
		spin_lock_init(&mos7840_port->pool_lock);

		/* minor is not initialised until later by
		 * usb-serial.c:get_free_serial() and cannot therefore be used
		 * to index device instances */
		mos7840_port->port_num = i + 1;
		dbg ("serial->port[i]->number = %d", serial->port[i]->number);
		dbg ("serial->port[i]->serial->minor = %d", serial->port[i]->serial->minor);
		dbg ("mos7840_port->port_num = %d", mos7840_port->port_num);
		dbg ("serial->minor = %d", serial->minor);

		if (mos7840_port->port_num == 1) {
			mos7840_port->SpRegOffset = 0x0;
			mos7840_port->ControlRegOffset = 0x1;
			mos7840_port->DcrRegOffset = 0x4;
		} else if ((mos7840_port->port_num == 2)
			   && (serial->num_ports == 4)) {
			mos7840_port->SpRegOffset = 0x8;
			mos7840_port->ControlRegOffset = 0x9;
			mos7840_port->DcrRegOffset = 0x16;
		} else if ((mos7840_port->port_num == 2)
			   && (serial->num_ports == 2)) {
			mos7840_port->SpRegOffset = 0xa;
			mos7840_port->ControlRegOffset = 0xb;
			mos7840_port->DcrRegOffset = 0x19;
		} else if ((mos7840_port->port_num == 3)
			   && (serial->num_ports == 4)) {
			mos7840_port->SpRegOffset = 0xa;
			mos7840_port->ControlRegOffset = 0xb;
			mos7840_port->DcrRegOffset = 0x19;
		} else if ((mos7840_port->port_num == 4)
			   && (serial->num_ports == 4)) {
			mos7840_port->SpRegOffset = 0xc;
			mos7840_port->ControlRegOffset = 0xd;
			mos7840_port->DcrRegOffset = 0x1c;
		}
		mos7840_dump_serial_port(mos7840_port);
		mos7840_set_port_private(serial->port[i], mos7840_port);

		/* enable rx_disable bit in control register */
		status = mos7840_get_reg_sync(serial->port[i],
				 mos7840_port->ControlRegOffset, &Data);
		if (status < 0) {
			dbg("Reading ControlReg failed status-0x%x", status);
			break;
		} else
			dbg("ControlReg Reading success val is %x, status%d",
			    Data, status);
		Data |= 0x08;	/* setting driver done bit */
		Data |= 0x04;	/* sp1_bit to have cts change reflect in
				   modem status reg */

		/* Data |= 0x20; //rx_disable bit */
		status = mos7840_set_reg_sync(serial->port[i],
					 mos7840_port->ControlRegOffset, Data);
		if (status < 0) {
			dbg("Writing ControlReg failed(rx_disable) status-0x%x", status);
			break;
		} else
			dbg("ControlReg Writing success(rx_disable) status%d",
			    status);

		/* Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2
		   and 0x24 in DCR3 */
		Data = 0x01;
		status = mos7840_set_reg_sync(serial->port[i],
			 (__u16) (mos7840_port->DcrRegOffset + 0), Data);
		if (status < 0) {
			dbg("Writing DCR0 failed status-0x%x", status);
			break;
		} else
			dbg("DCR0 Writing success status%d", status);

		Data = 0x05;
		status = mos7840_set_reg_sync(serial->port[i],
			 (__u16) (mos7840_port->DcrRegOffset + 1), Data);
		if (status < 0) {
			dbg("Writing DCR1 failed status-0x%x", status);
			break;
		} else
			dbg("DCR1 Writing success status%d", status);

		Data = 0x24;
		status = mos7840_set_reg_sync(serial->port[i],
			 (__u16) (mos7840_port->DcrRegOffset + 2), Data);
		if (status < 0) {
			dbg("Writing DCR2 failed status-0x%x", status);
			break;
		} else
			dbg("DCR2 Writing success status%d", status);

		/* write values in clkstart0x0 and clkmulti 0x20 */
		Data = 0x0;
		status = mos7840_set_reg_sync(serial->port[i],
					 CLK_START_VALUE_REGISTER, Data);
		if (status < 0) {
			dbg("Writing CLK_START_VALUE_REGISTER failed status-0x%x", status);
			break;
		} else
			dbg("CLK_START_VALUE_REGISTER Writing success status%d", status);

		Data = 0x20;
		status = mos7840_set_reg_sync(serial->port[i],
					CLK_MULTI_REGISTER, Data);
		if (status < 0) {
			dbg("Writing CLK_MULTI_REGISTER failed status-0x%x",
			    status);
			goto error;
		} else
			dbg("CLK_MULTI_REGISTER Writing success status%d",
			    status);

		/* write value 0x0 to scratchpad register */
		Data = 0x00;
		status = mos7840_set_uart_reg(serial->port[i],
						SCRATCH_PAD_REGISTER, Data);
		if (status < 0) {
			dbg("Writing SCRATCH_PAD_REGISTER failed status-0x%x",
			    status);
			break;
		} else
			dbg("SCRATCH_PAD_REGISTER Writing success status%d",
			    status);

		/* Zero Length flag register */
		if ((mos7840_port->port_num != 1)
		    && (serial->num_ports == 2)) {

			Data = 0xff;
			status = mos7840_set_reg_sync(serial->port[i],
				      (__u16) (ZLP_REG1 +
				      ((__u16)mos7840_port->port_num)), Data);
			dbg("ZLIP offset %x",
			    (__u16) (ZLP_REG1 +
					((__u16) mos7840_port->port_num)));
			if (status < 0) {
				dbg("Writing ZLP_REG%d failed status-0x%x",
				    i + 2, status);
				break;
			} else
				dbg("ZLP_REG%d Writing success status%d",
				    i + 2, status);
		} else {
			Data = 0xff;
			status = mos7840_set_reg_sync(serial->port[i],
			      (__u16) (ZLP_REG1 +
			      ((__u16)mos7840_port->port_num) - 0x1), Data);
			dbg("ZLIP offset %x",
			    (__u16) (ZLP_REG1 +
				     ((__u16) mos7840_port->port_num) - 0x1));
			if (status < 0) {
				dbg("Writing ZLP_REG%d failed status-0x%x",
				    i + 1, status);
				break;
			} else
				dbg("ZLP_REG%d Writing success status%d",
				    i + 1, status);

		}
		mos7840_port->control_urb = usb_alloc_urb(0, GFP_KERNEL);
		mos7840_port->ctrl_buf = kmalloc(16, GFP_KERNEL);
		mos7840_port->dr = kmalloc(sizeof(struct usb_ctrlrequest),
								GFP_KERNEL);
		if (!mos7840_port->control_urb || !mos7840_port->ctrl_buf ||
							!mos7840_port->dr) {
			status = -ENOMEM;
			goto error;
		}
	}
	dbg ("mos7840_startup: all ports configured...........");

	/* Zero Length flag enable */
	Data = 0x0f;
	status = mos7840_set_reg_sync(serial->port[0], ZLP_REG5, Data);
	if (status < 0) {
		dbg("Writing ZLP_REG5 failed status-0x%x", status);
		goto error;
	} else
		dbg("ZLP_REG5 Writing success status%d", status);

	/* setting configuration feature to one */
	usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
			(__u8) 0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5 * HZ);
	return 0;
error:
	for (/* nothing */; i >= 0; i--) {
		mos7840_port = mos7840_get_port_private(serial->port[i]);

		kfree(mos7840_port->dr);
		kfree(mos7840_port->ctrl_buf);
		usb_free_urb(mos7840_port->control_urb);
		kfree(mos7840_port);
		serial->port[i] = NULL;
	}
	return status;
}

/****************************************************************************
 * mos7840_disconnect
 *	This function is called whenever the device is removed from the usb bus.
 ****************************************************************************/

static void mos7840_disconnect(struct usb_serial *serial)
{
	int i;
	unsigned long flags;
	struct moschip_port *mos7840_port;
	dbg("%s", " disconnect :entering..........");

	if (!serial) {
		dbg("%s", "Invalid Handler");
		return;
	}

	/* check for the ports to be closed,close the ports and disconnect */

	/* free private structure allocated for serial port  *
	 * stop reads and writes on all ports                */

	for (i = 0; i < serial->num_ports; ++i) {
		mos7840_port = mos7840_get_port_private(serial->port[i]);
		dbg ("mos7840_port %d = %p", i, mos7840_port);
		if (mos7840_port) {
			spin_lock_irqsave(&mos7840_port->pool_lock, flags);
			mos7840_port->zombie = 1;
			spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
			usb_kill_urb(mos7840_port->control_urb);
		}
	}

	dbg("%s", "Thank u :: ");

}

/****************************************************************************
 * mos7840_release
 *	This function is called when the usb_serial structure is freed.
 ****************************************************************************/

static void mos7840_release(struct usb_serial *serial)
{
	int i;
	struct moschip_port *mos7840_port;
	dbg("%s", " release :entering..........");

	if (!serial) {
		dbg("%s", "Invalid Handler");
		return;
	}

	/* check for the ports to be closed,close the ports and disconnect */

	/* free private structure allocated for serial port  *
	 * stop reads and writes on all ports                */

	for (i = 0; i < serial->num_ports; ++i) {
		mos7840_port = mos7840_get_port_private(serial->port[i]);
		dbg("mos7840_port %d = %p", i, mos7840_port);
		if (mos7840_port) {
			kfree(mos7840_port->ctrl_buf);
			kfree(mos7840_port->dr);
			kfree(mos7840_port);
		}
	}

	dbg("%s", "Thank u :: ");

}

static struct usb_driver io_driver = {
	.name = "mos7840",
	.probe = usb_serial_probe,
	.disconnect = usb_serial_disconnect,
	.id_table = moschip_id_table_combined,
};

static struct usb_serial_driver moschip7840_4port_device = {
	.driver = {
		   .owner = THIS_MODULE,
		   .name = "mos7840",
		   },
	.description = DRIVER_DESC,
	.id_table = moschip_port_id_table,
	.num_ports = 4,
	.open = mos7840_open,
	.close = mos7840_close,
	.write = mos7840_write,
	.write_room = mos7840_write_room,
	.chars_in_buffer = mos7840_chars_in_buffer,
	.throttle = mos7840_throttle,
	.unthrottle = mos7840_unthrottle,
	.calc_num_ports = mos7840_calc_num_ports,
#ifdef MCSSerialProbe
	.probe = mos7840_serial_probe,
#endif
	.ioctl = mos7840_ioctl,
	.set_termios = mos7840_set_termios,
	.break_ctl = mos7840_break,
	.tiocmget = mos7840_tiocmget,
	.tiocmset = mos7840_tiocmset,
	.get_icount = mos7840_get_icount,
	.attach = mos7840_startup,
	.disconnect = mos7840_disconnect,
	.release = mos7840_release,
	.read_bulk_callback = mos7840_bulk_in_callback,
	.read_int_callback = mos7840_interrupt_callback,
};

static struct usb_serial_driver * const serial_drivers[] = {
	&moschip7840_4port_device, NULL
};

module_usb_serial_driver(io_driver, serial_drivers);

MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");

module_param(debug, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(debug, "Debug enabled or not");