# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/phy/socionext,uniphier-usb3hs-phy.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Socionext UniPhier USB3 High-Speed (HS) PHY

description: |
  This describes the devicetree bindings for PHY interfaces built into
  USB3 controller implemented on Socionext UniPhier SoCs.
  Although the controller includes High-Speed PHY and Super-Speed PHY,
  this describes about High-Speed PHY.

maintainers:
  - Kunihiko Hayashi <hayashi.kunihiko@socionext.com>

properties:
  compatible:
    enum:
      - socionext,uniphier-pro5-usb3-hsphy
      - socionext,uniphier-pxs2-usb3-hsphy
      - socionext,uniphier-ld20-usb3-hsphy
      - socionext,uniphier-pxs3-usb3-hsphy
      - socionext,uniphier-nx1-usb3-hsphy

  reg:
    maxItems: 1

  "#phy-cells":
    const: 0

  clocks:
    minItems: 2
    maxItems: 3

  clock-names: true

  resets:
    maxItems: 2

  reset-names: true

  vbus-supply:
    description: A phandle to the regulator for USB VBUS

  nvmem-cells:
    maxItems: 3
    description:
      Phandles to nvmem cell that contains the trimming data.
      Available only for HS-PHY implemented on LD20 and PXs3, and
      if unspecified, default value is used.

  nvmem-cell-names:
    items:
      - const: rterm
      - const: sel_t
      - const: hs_i
    description:
      Should be the following names, which correspond to each nvmem-cells.
      All of the 3 parameters associated with the above names are
      required for each port, if any one is omitted, the trimming data
      of the port will not be set at all.

allOf:
  - if:
      properties:
        compatible:
          contains:
            const: socionext,uniphier-pro5-usb3-hsphy
    then:
      properties:
        clocks:
          minItems: 2
          maxItems: 2
        clock-names:
          items:
            - const: gio
            - const: link
        resets:
          minItems: 2
          maxItems: 2
        reset-names:
          items:
            - const: gio
            - const: link
  - if:
      properties:
        compatible:
          contains:
            enum:
              - socionext,uniphier-pxs2-usb3-hsphy
              - socionext,uniphier-ld20-usb3-hsphy
    then:
      properties:
        clocks:
          minItems: 2
          maxItems: 2
        clock-names:
          items:
            - const: link
            - const: phy
        resets:
          minItems: 2
          maxItems: 2
        reset-names:
          items:
            - const: link
            - const: phy
  - if:
      properties:
        compatible:
          contains:
            enum:
              - socionext,uniphier-pxs3-usb3-hsphy
              - socionext,uniphier-nx1-usb3-hsphy
    then:
      properties:
        clocks:
          minItems: 2
          maxItems: 3
        clock-names:
          minItems: 2
          items:
            - const: link
            - const: phy
            - const: phy-ext
        resets:
          minItems: 2
          maxItems: 2
        reset-names:
          items:
            - const: link
            - const: phy

required:
  - compatible
  - reg
  - "#phy-cells"
  - clocks
  - clock-names
  - resets
  - reset-names

additionalProperties: false

examples:
  - |
    usb-glue@65b00000 {
        compatible = "socionext,uniphier-ld20-dwc3-glue", "simple-mfd";
        #address-cells = <1>;
        #size-cells = <1>;
        ranges = <0 0x65b00000 0x400>;

        usb_hsphy0: hs-phy@200 {
            compatible = "socionext,uniphier-ld20-usb3-hsphy";
            reg = <0x200 0x10>;
            #phy-cells = <0>;
            clock-names = "link", "phy";
            clocks = <&sys_clk 14>, <&sys_clk 16>;
            reset-names = "link", "phy";
            resets = <&sys_rst 14>, <&sys_rst 16>;
            vbus-supply = <&usb_vbus0>;
            nvmem-cell-names = "rterm", "sel_t", "hs_i";
            nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>, <&usb_hs_i0>;
        };
    };