Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/serial/pmac_zilog.h b/drivers/serial/pmac_zilog.h
new file mode 100644
index 0000000..c03f9bf
--- /dev/null
+++ b/drivers/serial/pmac_zilog.h
@@ -0,0 +1,382 @@
+#ifndef __PMAC_ZILOG_H__
+#define __PMAC_ZILOG_H__
+
+#define pmz_debug(fmt,arg...) dev_dbg(&uap->dev->ofdev.dev, fmt, ## arg)
+
+/*
+ * At most 2 ESCCs with 2 ports each
+ */
+#define MAX_ZS_PORTS 4
+
+/*
+ * We wrap our port structure around the generic uart_port.
+ */
+#define NUM_ZSREGS 17
+
+struct uart_pmac_port {
+ struct uart_port port;
+ struct uart_pmac_port *mate;
+
+ /* macio_dev for the escc holding this port (maybe be null on
+ * early inited port)
+ */
+ struct macio_dev *dev;
+ /* device node to this port, this points to one of 2 childs
+ * of "escc" node (ie. ch-a or ch-b)
+ */
+ struct device_node *node;
+
+ /* Port type as obtained from device tree (IRDA, modem, ...) */
+ int port_type;
+ u8 curregs[NUM_ZSREGS];
+
+ unsigned int flags;
+#define PMACZILOG_FLAG_IS_CONS 0x00000001
+#define PMACZILOG_FLAG_IS_KGDB 0x00000002
+#define PMACZILOG_FLAG_MODEM_STATUS 0x00000004
+#define PMACZILOG_FLAG_IS_CHANNEL_A 0x00000008
+#define PMACZILOG_FLAG_REGS_HELD 0x00000010
+#define PMACZILOG_FLAG_TX_STOPPED 0x00000020
+#define PMACZILOG_FLAG_TX_ACTIVE 0x00000040
+#define PMACZILOG_FLAG_ENABLED 0x00000080
+#define PMACZILOG_FLAG_IS_IRDA 0x00000100
+#define PMACZILOG_FLAG_IS_INTMODEM 0x00000200
+#define PMACZILOG_FLAG_HAS_DMA 0x00000400
+#define PMACZILOG_FLAG_RSRC_REQUESTED 0x00000800
+#define PMACZILOG_FLAG_IS_ASLEEP 0x00001000
+#define PMACZILOG_FLAG_IS_OPEN 0x00002000
+#define PMACZILOG_FLAG_IS_IRQ_ON 0x00004000
+#define PMACZILOG_FLAG_IS_EXTCLK 0x00008000
+#define PMACZILOG_FLAG_BREAK 0x00010000
+
+ unsigned char parity_mask;
+ unsigned char prev_status;
+
+ volatile u8 __iomem *control_reg;
+ volatile u8 __iomem *data_reg;
+
+ unsigned int tx_dma_irq;
+ unsigned int rx_dma_irq;
+ volatile struct dbdma_regs __iomem *tx_dma_regs;
+ volatile struct dbdma_regs __iomem *rx_dma_regs;
+
+ struct termios termios_cache;
+};
+
+#define to_pmz(p) ((struct uart_pmac_port *)(p))
+
+static inline struct uart_pmac_port *pmz_get_port_A(struct uart_pmac_port *uap)
+{
+ if (uap->flags & PMACZILOG_FLAG_IS_CHANNEL_A)
+ return uap;
+ return uap->mate;
+}
+
+/*
+ * Register acessors. Note that we don't need to enforce a recovery
+ * delay on PCI PowerMac hardware, it's dealt in HW by the MacIO chip,
+ * though if we try to use this driver on older machines, we might have
+ * to add it back
+ */
+static inline u8 read_zsreg(struct uart_pmac_port *port, u8 reg)
+{
+ if (reg != 0)
+ writeb(reg, port->control_reg);
+ return readb(port->control_reg);
+}
+
+static inline void write_zsreg(struct uart_pmac_port *port, u8 reg, u8 value)
+{
+ if (reg != 0)
+ writeb(reg, port->control_reg);
+ writeb(value, port->control_reg);
+}
+
+static inline u8 read_zsdata(struct uart_pmac_port *port)
+{
+ return readb(port->data_reg);
+}
+
+static inline void write_zsdata(struct uart_pmac_port *port, u8 data)
+{
+ writeb(data, port->data_reg);
+}
+
+static inline void zssync(struct uart_pmac_port *port)
+{
+ (void)readb(port->control_reg);
+}
+
+/* Conversion routines to/from brg time constants from/to bits
+ * per second.
+ */
+#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
+#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
+
+#define ZS_CLOCK 3686400 /* Z8530 RTxC input clock rate */
+
+/* The Zilog register set */
+
+#define FLAG 0x7e
+
+/* Write Register 0 */
+#define R0 0 /* Register selects */
+#define R1 1
+#define R2 2
+#define R3 3
+#define R4 4
+#define R5 5
+#define R6 6
+#define R7 7
+#define R8 8
+#define R9 9
+#define R10 10
+#define R11 11
+#define R12 12
+#define R13 13
+#define R14 14
+#define R15 15
+#define R7P 16
+
+#define NULLCODE 0 /* Null Code */
+#define POINT_HIGH 0x8 /* Select upper half of registers */
+#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
+#define SEND_ABORT 0x18 /* HDLC Abort */
+#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
+#define RES_Tx_P 0x28 /* Reset TxINT Pending */
+#define ERR_RES 0x30 /* Error Reset */
+#define RES_H_IUS 0x38 /* Reset highest IUS */
+
+#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
+#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
+#define RES_EOM_L 0xC0 /* Reset EOM latch */
+
+/* Write Register 1 */
+
+#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
+#define TxINT_ENAB 0x2 /* Tx Int Enable */
+#define PAR_SPEC 0x4 /* Parity is special condition */
+
+#define RxINT_DISAB 0 /* Rx Int Disable */
+#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
+#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
+#define INT_ERR_Rx 0x18 /* Int on error only */
+#define RxINT_MASK 0x18
+
+#define WT_RDY_RT 0x20 /* W/Req reflects recv if 1, xmit if 0 */
+#define WT_FN_RDYFN 0x40 /* W/Req pin is DMA request if 1, wait if 0 */
+#define WT_RDY_ENAB 0x80 /* Enable W/Req pin */
+
+/* Write Register #2 (Interrupt Vector) */
+
+/* Write Register 3 */
+
+#define RxENABLE 0x1 /* Rx Enable */
+#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
+#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
+#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
+#define ENT_HM 0x10 /* Enter Hunt Mode */
+#define AUTO_ENAB 0x20 /* Auto Enables */
+#define Rx5 0x0 /* Rx 5 Bits/Character */
+#define Rx7 0x40 /* Rx 7 Bits/Character */
+#define Rx6 0x80 /* Rx 6 Bits/Character */
+#define Rx8 0xc0 /* Rx 8 Bits/Character */
+#define RxN_MASK 0xc0
+
+/* Write Register 4 */
+
+#define PAR_ENAB 0x1 /* Parity Enable */
+#define PAR_EVEN 0x2 /* Parity Even/Odd* */
+
+#define SYNC_ENAB 0 /* Sync Modes Enable */
+#define SB1 0x4 /* 1 stop bit/char */
+#define SB15 0x8 /* 1.5 stop bits/char */
+#define SB2 0xc /* 2 stop bits/char */
+#define SB_MASK 0xc
+
+#define MONSYNC 0 /* 8 Bit Sync character */
+#define BISYNC 0x10 /* 16 bit sync character */
+#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
+#define EXTSYNC 0x30 /* External Sync Mode */
+
+#define X1CLK 0x0 /* x1 clock mode */
+#define X16CLK 0x40 /* x16 clock mode */
+#define X32CLK 0x80 /* x32 clock mode */
+#define X64CLK 0xC0 /* x64 clock mode */
+#define XCLK_MASK 0xC0
+
+/* Write Register 5 */
+
+#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
+#define RTS 0x2 /* RTS */
+#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
+#define TxENABLE 0x8 /* Tx Enable */
+#define SND_BRK 0x10 /* Send Break */
+#define Tx5 0x0 /* Tx 5 bits (or less)/character */
+#define Tx7 0x20 /* Tx 7 bits/character */
+#define Tx6 0x40 /* Tx 6 bits/character */
+#define Tx8 0x60 /* Tx 8 bits/character */
+#define TxN_MASK 0x60
+#define DTR 0x80 /* DTR */
+
+/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
+
+/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
+
+/* Write Register 7' (Some enhanced feature control) */
+#define ENEXREAD 0x40 /* Enable read of some write registers */
+
+/* Write Register 8 (transmit buffer) */
+
+/* Write Register 9 (Master interrupt control) */
+#define VIS 1 /* Vector Includes Status */
+#define NV 2 /* No Vector */
+#define DLC 4 /* Disable Lower Chain */
+#define MIE 8 /* Master Interrupt Enable */
+#define STATHI 0x10 /* Status high */
+#define NORESET 0 /* No reset on write to R9 */
+#define CHRB 0x40 /* Reset channel B */
+#define CHRA 0x80 /* Reset channel A */
+#define FHWRES 0xc0 /* Force hardware reset */
+
+/* Write Register 10 (misc control bits) */
+#define BIT6 1 /* 6 bit/8bit sync */
+#define LOOPMODE 2 /* SDLC Loop mode */
+#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
+#define MARKIDLE 8 /* Mark/flag on idle */
+#define GAOP 0x10 /* Go active on poll */
+#define NRZ 0 /* NRZ mode */
+#define NRZI 0x20 /* NRZI mode */
+#define FM1 0x40 /* FM1 (transition = 1) */
+#define FM0 0x60 /* FM0 (transition = 0) */
+#define CRCPS 0x80 /* CRC Preset I/O */
+
+/* Write Register 11 (Clock Mode control) */
+#define TRxCXT 0 /* TRxC = Xtal output */
+#define TRxCTC 1 /* TRxC = Transmit clock */
+#define TRxCBR 2 /* TRxC = BR Generator Output */
+#define TRxCDP 3 /* TRxC = DPLL output */
+#define TRxCOI 4 /* TRxC O/I */
+#define TCRTxCP 0 /* Transmit clock = RTxC pin */
+#define TCTRxCP 8 /* Transmit clock = TRxC pin */
+#define TCBR 0x10 /* Transmit clock = BR Generator output */
+#define TCDPLL 0x18 /* Transmit clock = DPLL output */
+#define RCRTxCP 0 /* Receive clock = RTxC pin */
+#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
+#define RCBR 0x40 /* Receive clock = BR Generator output */
+#define RCDPLL 0x60 /* Receive clock = DPLL output */
+#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
+
+/* Write Register 12 (lower byte of baud rate generator time constant) */
+
+/* Write Register 13 (upper byte of baud rate generator time constant) */
+
+/* Write Register 14 (Misc control bits) */
+#define BRENAB 1 /* Baud rate generator enable */
+#define BRSRC 2 /* Baud rate generator source */
+#define DTRREQ 4 /* DTR/Request function */
+#define AUTOECHO 8 /* Auto Echo */
+#define LOOPBAK 0x10 /* Local loopback */
+#define SEARCH 0x20 /* Enter search mode */
+#define RMC 0x40 /* Reset missing clock */
+#define DISDPLL 0x60 /* Disable DPLL */
+#define SSBR 0x80 /* Set DPLL source = BR generator */
+#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
+#define SFMM 0xc0 /* Set FM mode */
+#define SNRZI 0xe0 /* Set NRZI mode */
+
+/* Write Register 15 (external/status interrupt control) */
+#define EN85C30 1 /* Enable some 85c30-enhanced registers */
+#define ZCIE 2 /* Zero count IE */
+#define ENSTFIFO 4 /* Enable status FIFO (SDLC) */
+#define DCDIE 8 /* DCD IE */
+#define SYNCIE 0x10 /* Sync/hunt IE */
+#define CTSIE 0x20 /* CTS IE */
+#define TxUIE 0x40 /* Tx Underrun/EOM IE */
+#define BRKIE 0x80 /* Break/Abort IE */
+
+
+/* Read Register 0 */
+#define Rx_CH_AV 0x1 /* Rx Character Available */
+#define ZCOUNT 0x2 /* Zero count */
+#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
+#define DCD 0x8 /* DCD */
+#define SYNC_HUNT 0x10 /* Sync/hunt */
+#define CTS 0x20 /* CTS */
+#define TxEOM 0x40 /* Tx underrun */
+#define BRK_ABRT 0x80 /* Break/Abort */
+
+/* Read Register 1 */
+#define ALL_SNT 0x1 /* All sent */
+/* Residue Data for 8 Rx bits/char programmed */
+#define RES3 0x8 /* 0/3 */
+#define RES4 0x4 /* 0/4 */
+#define RES5 0xc /* 0/5 */
+#define RES6 0x2 /* 0/6 */
+#define RES7 0xa /* 0/7 */
+#define RES8 0x6 /* 0/8 */
+#define RES18 0xe /* 1/8 */
+#define RES28 0x0 /* 2/8 */
+/* Special Rx Condition Interrupts */
+#define PAR_ERR 0x10 /* Parity error */
+#define Rx_OVR 0x20 /* Rx Overrun Error */
+#define CRC_ERR 0x40 /* CRC/Framing Error */
+#define END_FR 0x80 /* End of Frame (SDLC) */
+
+/* Read Register 2 (channel b only) - Interrupt vector */
+#define CHB_Tx_EMPTY 0x00
+#define CHB_EXT_STAT 0x02
+#define CHB_Rx_AVAIL 0x04
+#define CHB_SPECIAL 0x06
+#define CHA_Tx_EMPTY 0x08
+#define CHA_EXT_STAT 0x0a
+#define CHA_Rx_AVAIL 0x0c
+#define CHA_SPECIAL 0x0e
+#define STATUS_MASK 0x06
+
+/* Read Register 3 (interrupt pending register) ch a only */
+#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
+#define CHBTxIP 0x2 /* Channel B Tx IP */
+#define CHBRxIP 0x4 /* Channel B Rx IP */
+#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
+#define CHATxIP 0x10 /* Channel A Tx IP */
+#define CHARxIP 0x20 /* Channel A Rx IP */
+
+/* Read Register 8 (receive data register) */
+
+/* Read Register 10 (misc status bits) */
+#define ONLOOP 2 /* On loop */
+#define LOOPSEND 0x10 /* Loop sending */
+#define CLK2MIS 0x40 /* Two clocks missing */
+#define CLK1MIS 0x80 /* One clock missing */
+
+/* Read Register 12 (lower byte of baud rate generator constant) */
+
+/* Read Register 13 (upper byte of baud rate generator constant) */
+
+/* Read Register 15 (value of WR 15) */
+
+/* Misc macros */
+#define ZS_CLEARERR(port) (write_zsreg(port, 0, ERR_RES))
+#define ZS_CLEARFIFO(port) do { volatile unsigned char garbage; \
+ garbage = read_zsdata(port); \
+ garbage = read_zsdata(port); \
+ garbage = read_zsdata(port); \
+ } while(0)
+
+#define ZS_IS_CONS(UP) ((UP)->flags & PMACZILOG_FLAG_IS_CONS)
+#define ZS_IS_KGDB(UP) ((UP)->flags & PMACZILOG_FLAG_IS_KGDB)
+#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & PMACZILOG_FLAG_IS_CHANNEL_A)
+#define ZS_REGS_HELD(UP) ((UP)->flags & PMACZILOG_FLAG_REGS_HELD)
+#define ZS_TX_STOPPED(UP) ((UP)->flags & PMACZILOG_FLAG_TX_STOPPED)
+#define ZS_TX_ACTIVE(UP) ((UP)->flags & PMACZILOG_FLAG_TX_ACTIVE)
+#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & PMACZILOG_FLAG_MODEM_STATUS)
+#define ZS_IS_IRDA(UP) ((UP)->flags & PMACZILOG_FLAG_IS_IRDA)
+#define ZS_IS_INTMODEM(UP) ((UP)->flags & PMACZILOG_FLAG_IS_INTMODEM)
+#define ZS_HAS_DMA(UP) ((UP)->flags & PMACZILOG_FLAG_HAS_DMA)
+#define ZS_IS_ASLEEP(UP) ((UP)->flags & PMACZILOG_FLAG_IS_ASLEEP)
+#define ZS_IS_OPEN(UP) ((UP)->flags & PMACZILOG_FLAG_IS_OPEN)
+#define ZS_IS_IRQ_ON(UP) ((UP)->flags & PMACZILOG_FLAG_IS_IRQ_ON)
+#define ZS_IS_EXTCLK(UP) ((UP)->flags & PMACZILOG_FLAG_IS_EXTCLK)
+
+#endif /* __PMAC_ZILOG_H__ */
