[ARM] pxa: move AC97 register definitions into dedicated regs-ac97.h
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h
index cb9b46d..a565028 100644
--- a/arch/arm/mach-pxa/include/mach/pxa-regs.h
+++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h
@@ -132,102 +132,6 @@
*/
/*
- * AC97 Controller registers
- */
-
-#define POCR __REG(0x40500000) /* PCM Out Control Register */
-#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
-#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
-
-#define PICR __REG(0x40500004) /* PCM In Control Register */
-#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
-#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
-
-#define MCCR __REG(0x40500008) /* Mic In Control Register */
-#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
-#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
-
-#define GCR __REG(0x4050000C) /* Global Control Register */
-#ifdef CONFIG_PXA3xx
-#define GCR_CLKBPB (1 << 31) /* Internal clock enable */
-#endif
-#define GCR_nDMAEN (1 << 24) /* non DMA Enable */
-#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
-#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
-#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */
-#define GCR_PRIRDY_IEN (1 << 8) /* Primary Ready Interrupt Enable */
-#define GCR_SECRES_IEN (1 << 5) /* Secondary Resume Interrupt Enable */
-#define GCR_PRIRES_IEN (1 << 4) /* Primary Resume Interrupt Enable */
-#define GCR_ACLINK_OFF (1 << 3) /* AC-link Shut Off */
-#define GCR_WARM_RST (1 << 2) /* AC97 Warm Reset */
-#define GCR_COLD_RST (1 << 1) /* AC'97 Cold Reset (0 = active) */
-#define GCR_GIE (1 << 0) /* Codec GPI Interrupt Enable */
-
-#define POSR __REG(0x40500010) /* PCM Out Status Register */
-#define POSR_FIFOE (1 << 4) /* FIFO error */
-#define POSR_FSR (1 << 2) /* FIFO Service Request */
-
-#define PISR __REG(0x40500014) /* PCM In Status Register */
-#define PISR_FIFOE (1 << 4) /* FIFO error */
-#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
-#define PISR_FSR (1 << 2) /* FIFO Service Request */
-
-#define MCSR __REG(0x40500018) /* Mic In Status Register */
-#define MCSR_FIFOE (1 << 4) /* FIFO error */
-#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
-#define MCSR_FSR (1 << 2) /* FIFO Service Request */
-
-#define GSR __REG(0x4050001C) /* Global Status Register */
-#define GSR_CDONE (1 << 19) /* Command Done */
-#define GSR_SDONE (1 << 18) /* Status Done */
-#define GSR_RDCS (1 << 15) /* Read Completion Status */
-#define GSR_BIT3SLT12 (1 << 14) /* Bit 3 of slot 12 */
-#define GSR_BIT2SLT12 (1 << 13) /* Bit 2 of slot 12 */
-#define GSR_BIT1SLT12 (1 << 12) /* Bit 1 of slot 12 */
-#define GSR_SECRES (1 << 11) /* Secondary Resume Interrupt */
-#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */
-#define GSR_SCR (1 << 9) /* Secondary Codec Ready */
-#define GSR_PCR (1 << 8) /* Primary Codec Ready */
-#define GSR_MCINT (1 << 7) /* Mic In Interrupt */
-#define GSR_POINT (1 << 6) /* PCM Out Interrupt */
-#define GSR_PIINT (1 << 5) /* PCM In Interrupt */
-#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */
-#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */
-#define GSR_MIINT (1 << 1) /* Modem In Interrupt */
-#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */
-
-#define CAR __REG(0x40500020) /* CODEC Access Register */
-#define CAR_CAIP (1 << 0) /* Codec Access In Progress */
-
-#define PCDR __REG(0x40500040) /* PCM FIFO Data Register */
-#define MCDR __REG(0x40500060) /* Mic-in FIFO Data Register */
-
-#define MOCR __REG(0x40500100) /* Modem Out Control Register */
-#define MOCR_FEIE (1 << 3) /* FIFO Error */
-#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
-
-#define MICR __REG(0x40500108) /* Modem In Control Register */
-#define MICR_FEIE (1 << 3) /* FIFO Error */
-#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
-
-#define MOSR __REG(0x40500110) /* Modem Out Status Register */
-#define MOSR_FIFOE (1 << 4) /* FIFO error */
-#define MOSR_FSR (1 << 2) /* FIFO Service Request */
-
-#define MISR __REG(0x40500118) /* Modem In Status Register */
-#define MISR_FIFOE (1 << 4) /* FIFO error */
-#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
-#define MISR_FSR (1 << 2) /* FIFO Service Request */
-
-#define MODR __REG(0x40500140) /* Modem FIFO Data Register */
-
-#define PAC_REG_BASE __REG(0x40500200) /* Primary Audio Codec */
-#define SAC_REG_BASE __REG(0x40500300) /* Secondary Audio Codec */
-#define PMC_REG_BASE __REG(0x40500400) /* Primary Modem Codec */
-#define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */
-
-
-/*
* Fast Infrared Communication Port - moved into drivers/net/irda/pxaficp_ir.c
*/
diff --git a/arch/arm/mach-pxa/include/mach/regs-ac97.h b/arch/arm/mach-pxa/include/mach/regs-ac97.h
new file mode 100644
index 0000000..e41b9d2
--- /dev/null
+++ b/arch/arm/mach-pxa/include/mach/regs-ac97.h
@@ -0,0 +1,99 @@
+#ifndef __ASM_ARCH_REGS_AC97_H
+#define __ASM_ARCH_REGS_AC97_H
+
+/*
+ * AC97 Controller registers
+ */
+
+#define POCR __REG(0x40500000) /* PCM Out Control Register */
+#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
+
+#define PICR __REG(0x40500004) /* PCM In Control Register */
+#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
+
+#define MCCR __REG(0x40500008) /* Mic In Control Register */
+#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */
+#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
+
+#define GCR __REG(0x4050000C) /* Global Control Register */
+#ifdef CONFIG_PXA3xx
+#define GCR_CLKBPB (1 << 31) /* Internal clock enable */
+#endif
+#define GCR_nDMAEN (1 << 24) /* non DMA Enable */
+#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */
+#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */
+#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */
+#define GCR_PRIRDY_IEN (1 << 8) /* Primary Ready Interrupt Enable */
+#define GCR_SECRES_IEN (1 << 5) /* Secondary Resume Interrupt Enable */
+#define GCR_PRIRES_IEN (1 << 4) /* Primary Resume Interrupt Enable */
+#define GCR_ACLINK_OFF (1 << 3) /* AC-link Shut Off */
+#define GCR_WARM_RST (1 << 2) /* AC97 Warm Reset */
+#define GCR_COLD_RST (1 << 1) /* AC'97 Cold Reset (0 = active) */
+#define GCR_GIE (1 << 0) /* Codec GPI Interrupt Enable */
+
+#define POSR __REG(0x40500010) /* PCM Out Status Register */
+#define POSR_FIFOE (1 << 4) /* FIFO error */
+#define POSR_FSR (1 << 2) /* FIFO Service Request */
+
+#define PISR __REG(0x40500014) /* PCM In Status Register */
+#define PISR_FIFOE (1 << 4) /* FIFO error */
+#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define PISR_FSR (1 << 2) /* FIFO Service Request */
+
+#define MCSR __REG(0x40500018) /* Mic In Status Register */
+#define MCSR_FIFOE (1 << 4) /* FIFO error */
+#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MCSR_FSR (1 << 2) /* FIFO Service Request */
+
+#define GSR __REG(0x4050001C) /* Global Status Register */
+#define GSR_CDONE (1 << 19) /* Command Done */
+#define GSR_SDONE (1 << 18) /* Status Done */
+#define GSR_RDCS (1 << 15) /* Read Completion Status */
+#define GSR_BIT3SLT12 (1 << 14) /* Bit 3 of slot 12 */
+#define GSR_BIT2SLT12 (1 << 13) /* Bit 2 of slot 12 */
+#define GSR_BIT1SLT12 (1 << 12) /* Bit 1 of slot 12 */
+#define GSR_SECRES (1 << 11) /* Secondary Resume Interrupt */
+#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */
+#define GSR_SCR (1 << 9) /* Secondary Codec Ready */
+#define GSR_PCR (1 << 8) /* Primary Codec Ready */
+#define GSR_MCINT (1 << 7) /* Mic In Interrupt */
+#define GSR_POINT (1 << 6) /* PCM Out Interrupt */
+#define GSR_PIINT (1 << 5) /* PCM In Interrupt */
+#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */
+#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */
+#define GSR_MIINT (1 << 1) /* Modem In Interrupt */
+#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */
+
+#define CAR __REG(0x40500020) /* CODEC Access Register */
+#define CAR_CAIP (1 << 0) /* Codec Access In Progress */
+
+#define PCDR __REG(0x40500040) /* PCM FIFO Data Register */
+#define MCDR __REG(0x40500060) /* Mic-in FIFO Data Register */
+
+#define MOCR __REG(0x40500100) /* Modem Out Control Register */
+#define MOCR_FEIE (1 << 3) /* FIFO Error */
+#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
+
+#define MICR __REG(0x40500108) /* Modem In Control Register */
+#define MICR_FEIE (1 << 3) /* FIFO Error */
+#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */
+
+#define MOSR __REG(0x40500110) /* Modem Out Status Register */
+#define MOSR_FIFOE (1 << 4) /* FIFO error */
+#define MOSR_FSR (1 << 2) /* FIFO Service Request */
+
+#define MISR __REG(0x40500118) /* Modem In Status Register */
+#define MISR_FIFOE (1 << 4) /* FIFO error */
+#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */
+#define MISR_FSR (1 << 2) /* FIFO Service Request */
+
+#define MODR __REG(0x40500140) /* Modem FIFO Data Register */
+
+#define PAC_REG_BASE __REG(0x40500200) /* Primary Audio Codec */
+#define SAC_REG_BASE __REG(0x40500300) /* Secondary Audio Codec */
+#define PMC_REG_BASE __REG(0x40500400) /* Primary Modem Codec */
+#define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */
+
+#endif /* __ASM_ARCH_REGS_AC97_H */
diff --git a/drivers/input/touchscreen/mainstone-wm97xx.c b/drivers/input/touchscreen/mainstone-wm97xx.c
index ba64875..1d11e2b 100644
--- a/drivers/input/touchscreen/mainstone-wm97xx.c
+++ b/drivers/input/touchscreen/mainstone-wm97xx.c
@@ -31,7 +31,7 @@
#include <linux/interrupt.h>
#include <linux/wm97xx.h>
#include <linux/io.h>
-#include <mach/pxa-regs.h>
+#include <mach/regs-ac97.h>
#define VERSION "0.13"
diff --git a/sound/arm/pxa2xx-ac97-lib.c b/sound/arm/pxa2xx-ac97-lib.c
index 34c1d94..ef6539e 100644
--- a/sound/arm/pxa2xx-ac97-lib.c
+++ b/sound/arm/pxa2xx-ac97-lib.c
@@ -22,7 +22,7 @@
#include <asm/irq.h>
#include <mach/hardware.h>
-#include <mach/pxa-regs.h>
+#include <mach/regs-ac97.h>
#include <mach/pxa2xx-gpio.h>
#include <mach/audio.h>
diff --git a/sound/arm/pxa2xx-ac97.c b/sound/arm/pxa2xx-ac97.c
index c2635be..85cf591 100644
--- a/sound/arm/pxa2xx-ac97.c
+++ b/sound/arm/pxa2xx-ac97.c
@@ -22,6 +22,7 @@
#include <mach/hardware.h>
#include <mach/pxa-regs.h>
+#include <mach/regs-ac97.h>
#include <mach/audio.h>
#include "pxa2xx-pcm.h"
diff --git a/sound/soc/pxa/pxa2xx-ac97.c b/sound/soc/pxa/pxa2xx-ac97.c
index a7a3a9c..5e72739 100644
--- a/sound/soc/pxa/pxa2xx-ac97.c
+++ b/sound/soc/pxa/pxa2xx-ac97.c
@@ -21,6 +21,7 @@
#include <mach/hardware.h>
#include <mach/pxa-regs.h>
+#include <mach/regs-ac97.h>
#include "pxa2xx-pcm.h"
#include "pxa2xx-ac97.h"
