diff --git a/arch/arm/boot/dts/iwg20d-q7-common.dtsi b/arch/arm/boot/dts/iwg20d-q7-common.dtsi
index ebbe151..63cafd2 100644
--- a/arch/arm/boot/dts/iwg20d-q7-common.dtsi
+++ b/arch/arm/boot/dts/iwg20d-q7-common.dtsi
@@ -57,7 +57,7 @@ lcd_backlight: backlight {
 
 	lvds-receiver {
 		compatible = "ti,ds90cf384a", "lvds-decoder";
-		powerdown-gpios = <&gpio7 25 GPIO_ACTIVE_LOW>;
+		power-supply = <&vcc_3v3_tft1>;
 
 		ports {
 			#address-cells = <1>;
@@ -81,6 +81,7 @@ lvds_receiver_out: endpoint {
 	panel {
 		compatible = "edt,etm0700g0dh6";
 		backlight = <&lcd_backlight>;
+		power-supply = <&vcc_3v3_tft1>;
 
 		port {
 			panel_in: endpoint {
@@ -113,6 +114,17 @@ sndcodec: simple-audio-card,codec {
 		};
 	};
 
+	vcc_3v3_tft1: regulator-panel {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vcc-3v3-tft1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		startup-delay-us = <500>;
+		gpio = <&gpio7 25 GPIO_ACTIVE_HIGH>;
+	};
+
 	vcc_sdhi1: regulator-vcc-sdhi1 {
 		compatible = "regulator-fixed";
 
@@ -207,6 +219,7 @@ touch: touchpanel@38 {
 		reg = <0x38>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&vcc_3v3_tft1>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
index 42d62d1..ea15073 100644
--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -223,16 +223,16 @@ &reg_aldo3 {
 };
 
 &reg_dc1sw {
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-gmac-phy";
 };
 
 &reg_dcdc1 {
 	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "vcc-3v0";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
 };
 
 &reg_dcdc2 {
diff --git a/arch/arm/mach-omap2/cpuidle44xx.c b/arch/arm/mach-omap2/cpuidle44xx.c
index 6f5f897..a92d277 100644
--- a/arch/arm/mach-omap2/cpuidle44xx.c
+++ b/arch/arm/mach-omap2/cpuidle44xx.c
@@ -174,8 +174,10 @@ static int omap_enter_idle_coupled(struct cpuidle_device *dev,
 		 */
 		if (mpuss_can_lose_context) {
 			error = cpu_cluster_pm_enter();
-			if (error)
+			if (error) {
+				omap_set_pwrdm_state(mpu_pd, PWRDM_POWER_ON);
 				goto cpu_cluster_pm_out;
+			}
 		}
 	}
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
index 6735e31..6c6053a 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -139,8 +139,7 @@ mali: gpu@1e80000 {
 				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "gp",
 					  "gpmmu",
 					  "pp",
@@ -151,8 +150,7 @@ mali: gpu@1e80000 {
 					  "pp2",
 					  "ppmmu2",
 					  "pp3",
-					  "ppmmu3",
-					  "pmu";
+					  "ppmmu3";
 			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
 			clock-names = "bus", "core";
 			resets = <&ccu RST_BUS_GPU>;
diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi
index 4032b74..791f254 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi
@@ -221,7 +221,12 @@ pmi8994_regulators: pmi8994-regulators {
 };
 
 &sdhc1 {
-	status = "okay";
+	/* There is an issue with the eMMC causing permanent
+	 * damage to the card if a quirk isn't addressed.
+	 * Until it's fixed, disable the MMC so as not to brick
+	 * devices.
+	 */
+	status = "disabled";
 
 	/* Downstream pushes 2.95V to the sdhci device,
 	 * but upstream driver REALLY wants to make vmmc 1.8v
diff --git a/arch/arm64/boot/dts/qcom/pm660.dtsi b/arch/arm64/boot/dts/qcom/pm660.dtsi
index ea0e955..2e6a6f6 100644
--- a/arch/arm64/boot/dts/qcom/pm660.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm660.dtsi
@@ -44,7 +44,7 @@ pm660_gpios: gpios@c000 {
 			gpio-ranges = <&pm660_gpios 0 0 13>;
 			#gpio-cells = <2>;
 			interrupt-controller;
-			interrupt-cells =<2>;
+			#interrupt-cells = <2>;
 		};
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi
index 88efe82..deb928d 100644
--- a/arch/arm64/boot/dts/qcom/sdm630.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi
@@ -518,6 +518,8 @@ anoc2_smmu: iommu@16c0000 {
 				<GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>;
+
+			status = "disabled";
 		};
 
 		tcsr_mutex_regs: syscon@1f40000 {
@@ -749,6 +751,8 @@ kgsl_smmu: iommu@5040000 {
 				<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>;
+
+			status = "disabled";
 		};
 
 		lpass_smmu: iommu@5100000 {
@@ -778,6 +782,8 @@ lpass_smmu: iommu@5100000 {
 				<GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>;
+
+			status = "disabled";
 		};
 
 		spmi_bus: spmi@800f000 {
@@ -1074,6 +1080,8 @@ mmss_smmu: iommu@cd00000 {
 				<GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>;
+
+			status = "disabled";
 		};
 
 		apcs_glb: mailbox@17911000 {
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index 2884577..eca81cf 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -1093,8 +1093,8 @@ rng: rng@793000 {
 		qup_opp_table: qup-opp-table {
 			compatible = "operating-points-v2";
 
-			opp-19200000 {
-				opp-hz = /bits/ 64 <19200000>;
+			opp-50000000 {
+				opp-hz = /bits/ 64 <50000000>;
 				required-opps = <&rpmhpd_opp_min_svs>;
 			};
 
@@ -1107,6 +1107,11 @@ opp-100000000 {
 				opp-hz = /bits/ 64 <100000000>;
 				required-opps = <&rpmhpd_opp_svs>;
 			};
+
+			opp-128000000 {
+				opp-hz = /bits/ 64 <128000000>;
+				required-opps = <&rpmhpd_opp_nom>;
+			};
 		};
 
 		qupv3_id_0: geniqup@8c0000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index e8fc01d..6f7490e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -404,11 +404,12 @@ &usb_serdes_mux {
 };
 
 &serdes_ln_ctrl {
-	idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
-		      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
-		      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
-		      <SERDES3_LANE0_USB3_0_SWAP>, <SERDES3_LANE1_USB3_0>,
-		      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+	idle-states = <J721E_SERDES0_LANE0_PCIE0_LANE0>, <J721E_SERDES0_LANE1_PCIE0_LANE1>,
+		      <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>,
+		      <J721E_SERDES2_LANE0_PCIE2_LANE0>, <J721E_SERDES2_LANE1_PCIE2_LANE1>,
+		      <J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
+		      <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
+		      <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
 };
 
 &serdes_wiz3 {
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 12ceea9..63d221a 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -6,7 +6,7 @@
  */
 #include <dt-bindings/phy/phy.h>
 #include <dt-bindings/mux/mux.h>
-#include <dt-bindings/mux/mux-j721e-wiz.h>
+#include <dt-bindings/mux/ti-serdes.h>
 
 &cbass_main {
 	msmc_ram: sram@70000000 {
@@ -38,11 +38,12 @@ serdes_ln_ctrl: serdes-ln-ctrl@4080 {
 					<0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
 					<0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
 					/* SERDES4 lane0/1/2/3 select */
-			idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
-				      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
-				      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
-				      <MUX_IDLE_AS_IS>, <SERDES3_LANE1_USB3_0>,
-				      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+			idle-states = <J721E_SERDES0_LANE0_PCIE0_LANE0>, <J721E_SERDES0_LANE1_PCIE0_LANE1>,
+				      <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>,
+				      <J721E_SERDES2_LANE0_PCIE2_LANE0>, <J721E_SERDES2_LANE1_PCIE2_LANE1>,
+				      <MUX_IDLE_AS_IS>, <J721E_SERDES3_LANE1_USB3_0>,
+				      <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
+				      <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
 		};
 
 		usb_serdes_mux: mux-controller@4000 {
diff --git a/drivers/soc/actions/owl-sps-helper.c b/drivers/soc/actions/owl-sps-helper.c
index 291a206..e3f3660 100644
--- a/drivers/soc/actions/owl-sps-helper.c
+++ b/drivers/soc/actions/owl-sps-helper.c
@@ -10,6 +10,7 @@
 
 #include <linux/delay.h>
 #include <linux/io.h>
+#include <linux/soc/actions/owl-sps.h>
 
 #define OWL_SPS_PG_CTL	0x0
 
diff --git a/drivers/soc/qcom/pdr_internal.h b/drivers/soc/qcom/pdr_internal.h
index 15b5002..ab9ae8c 100644
--- a/drivers/soc/qcom/pdr_internal.h
+++ b/drivers/soc/qcom/pdr_internal.h
@@ -185,7 +185,7 @@ struct qmi_elem_info servreg_get_domain_list_resp_ei[] = {
 		.data_type      = QMI_STRUCT,
 		.elem_len       = SERVREG_DOMAIN_LIST_LENGTH,
 		.elem_size      = sizeof(struct servreg_location_entry),
-		.array_type	= NO_ARRAY,
+		.array_type	= VAR_LEN_ARRAY,
 		.tlv_type       = 0x12,
 		.offset         = offsetof(struct servreg_get_domain_list_resp,
 					   domain_list),
diff --git a/drivers/soc/xilinx/zynqmp_power.c b/drivers/soc/xilinx/zynqmp_power.c
index 31ff49f..c556623 100644
--- a/drivers/soc/xilinx/zynqmp_power.c
+++ b/drivers/soc/xilinx/zynqmp_power.c
@@ -205,7 +205,7 @@ static int zynqmp_pm_probe(struct platform_device *pdev)
 		rx_chan = mbox_request_channel_byname(client, "rx");
 		if (IS_ERR(rx_chan)) {
 			dev_err(&pdev->dev, "Failed to request rx channel\n");
-			return IS_ERR(rx_chan);
+			return PTR_ERR(rx_chan);
 		}
 	} else if (of_find_property(pdev->dev.of_node, "interrupts", NULL)) {
 		irq = platform_get_irq(pdev, 0);
diff --git a/include/dt-bindings/mux/mux-j721e-wiz.h b/include/dt-bindings/mux/mux-j721e-wiz.h
deleted file mode 100644
index fd1c4ea..0000000
--- a/include/dt-bindings/mux/mux-j721e-wiz.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * This header provides constants for J721E WIZ.
- */
-
-#ifndef _DT_BINDINGS_J721E_WIZ
-#define _DT_BINDINGS_J721E_WIZ
-
-#define SERDES0_LANE0_QSGMII_LANE1	0x0
-#define SERDES0_LANE0_PCIE0_LANE0	0x1
-#define SERDES0_LANE0_USB3_0_SWAP	0x2
-
-#define SERDES0_LANE1_QSGMII_LANE2	0x0
-#define SERDES0_LANE1_PCIE0_LANE1	0x1
-#define SERDES0_LANE1_USB3_0		0x2
-
-#define SERDES1_LANE0_QSGMII_LANE3	0x0
-#define SERDES1_LANE0_PCIE1_LANE0	0x1
-#define SERDES1_LANE0_USB3_1_SWAP	0x2
-#define SERDES1_LANE0_SGMII_LANE0	0x3
-
-#define SERDES1_LANE1_QSGMII_LANE4	0x0
-#define SERDES1_LANE1_PCIE1_LANE1	0x1
-#define SERDES1_LANE1_USB3_1		0x2
-#define SERDES1_LANE1_SGMII_LANE1	0x3
-
-#define SERDES2_LANE0_PCIE2_LANE0	0x1
-#define SERDES2_LANE0_SGMII_LANE0	0x3
-#define SERDES2_LANE0_USB3_1_SWAP	0x2
-
-#define SERDES2_LANE1_PCIE2_LANE1	0x1
-#define SERDES2_LANE1_USB3_1		0x2
-#define SERDES2_LANE1_SGMII_LANE1	0x3
-
-#define SERDES3_LANE0_PCIE3_LANE0	0x1
-#define SERDES3_LANE0_USB3_0_SWAP	0x2
-
-#define SERDES3_LANE1_PCIE3_LANE1	0x1
-#define SERDES3_LANE1_USB3_0		0x2
-
-#define SERDES4_LANE0_EDP_LANE0		0x0
-#define SERDES4_LANE0_QSGMII_LANE5	0x2
-
-#define SERDES4_LANE1_EDP_LANE1		0x0
-#define SERDES4_LANE1_QSGMII_LANE6	0x2
-
-#define SERDES4_LANE2_EDP_LANE2		0x0
-#define SERDES4_LANE2_QSGMII_LANE7	0x2
-
-#define SERDES4_LANE3_EDP_LANE3		0x0
-#define SERDES4_LANE3_QSGMII_LANE8	0x2
-
-#endif /* _DT_BINDINGS_J721E_WIZ */
diff --git a/include/dt-bindings/mux/ti-serdes.h b/include/dt-bindings/mux/ti-serdes.h
new file mode 100644
index 0000000..146d068
--- /dev/null
+++ b/include/dt-bindings/mux/ti-serdes.h
@@ -0,0 +1,71 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides constants for SERDES MUX for TI SoCs
+ */
+
+#ifndef _DT_BINDINGS_MUX_TI_SERDES
+#define _DT_BINDINGS_MUX_TI_SERDES
+
+/* J721E */
+
+#define J721E_SERDES0_LANE0_QSGMII_LANE1	0x0
+#define J721E_SERDES0_LANE0_PCIE0_LANE0		0x1
+#define J721E_SERDES0_LANE0_USB3_0_SWAP		0x2
+#define J721E_SERDES0_LANE0_IP4_UNUSED		0x3
+
+#define J721E_SERDES0_LANE1_QSGMII_LANE2	0x0
+#define J721E_SERDES0_LANE1_PCIE0_LANE1		0x1
+#define J721E_SERDES0_LANE1_USB3_0		0x2
+#define J721E_SERDES0_LANE1_IP4_UNUSED		0x3
+
+#define J721E_SERDES1_LANE0_QSGMII_LANE3	0x0
+#define J721E_SERDES1_LANE0_PCIE1_LANE0		0x1
+#define J721E_SERDES1_LANE0_USB3_1_SWAP		0x2
+#define J721E_SERDES1_LANE0_SGMII_LANE0		0x3
+
+#define J721E_SERDES1_LANE1_QSGMII_LANE4	0x0
+#define J721E_SERDES1_LANE1_PCIE1_LANE1		0x1
+#define J721E_SERDES1_LANE1_USB3_1		0x2
+#define J721E_SERDES1_LANE1_SGMII_LANE1		0x3
+
+#define J721E_SERDES2_LANE0_IP1_UNUSED		0x0
+#define J721E_SERDES2_LANE0_PCIE2_LANE0		0x1
+#define J721E_SERDES2_LANE0_USB3_1_SWAP		0x2
+#define J721E_SERDES2_LANE0_SGMII_LANE0		0x3
+
+#define J721E_SERDES2_LANE1_IP1_UNUSED		0x0
+#define J721E_SERDES2_LANE1_PCIE2_LANE1		0x1
+#define J721E_SERDES2_LANE1_USB3_1		0x2
+#define J721E_SERDES2_LANE1_SGMII_LANE1		0x3
+
+#define J721E_SERDES3_LANE0_IP1_UNUSED		0x0
+#define J721E_SERDES3_LANE0_PCIE3_LANE0		0x1
+#define J721E_SERDES3_LANE0_USB3_0_SWAP		0x2
+#define J721E_SERDES3_LANE0_IP4_UNUSED		0x3
+
+#define J721E_SERDES3_LANE1_IP1_UNUSED		0x0
+#define J721E_SERDES3_LANE1_PCIE3_LANE1		0x1
+#define J721E_SERDES3_LANE1_USB3_0		0x2
+#define J721E_SERDES3_LANE1_IP4_UNUSED		0x3
+
+#define J721E_SERDES4_LANE0_EDP_LANE0		0x0
+#define J721E_SERDES4_LANE0_IP2_UNUSED		0x1
+#define J721E_SERDES4_LANE0_QSGMII_LANE5	0x2
+#define J721E_SERDES4_LANE0_IP4_UNUSED		0x3
+
+#define J721E_SERDES4_LANE1_EDP_LANE1		0x0
+#define J721E_SERDES4_LANE1_IP2_UNUSED		0x1
+#define J721E_SERDES4_LANE1_QSGMII_LANE6	0x2
+#define J721E_SERDES4_LANE1_IP4_UNUSED		0x3
+
+#define J721E_SERDES4_LANE2_EDP_LANE2		0x0
+#define J721E_SERDES4_LANE2_IP2_UNUSED		0x1
+#define J721E_SERDES4_LANE2_QSGMII_LANE7	0x2
+#define J721E_SERDES4_LANE2_IP4_UNUSED		0x3
+
+#define J721E_SERDES4_LANE3_EDP_LANE3		0x0
+#define J721E_SERDES4_LANE3_IP2_UNUSED		0x1
+#define J721E_SERDES4_LANE3_QSGMII_LANE8	0x2
+#define J721E_SERDES4_LANE3_IP4_UNUSED		0x3
+
+#endif /* _DT_BINDINGS_MUX_TI_SERDES */
diff --git a/include/dt-bindings/pinctrl/omap.h b/include/dt-bindings/pinctrl/omap.h
index 2d2a8c7..f48245f 100644
--- a/include/dt-bindings/pinctrl/omap.h
+++ b/include/dt-bindings/pinctrl/omap.h
@@ -64,7 +64,7 @@
 #define OMAP3_WKUP_IOPAD(pa, val)	OMAP_IOPAD_OFFSET((pa), 0x2a00) (val)
 #define DM814X_IOPAD(pa, val)		OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
 #define DM816X_IOPAD(pa, val)		OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
-#define AM33XX_IOPAD(pa, val)		OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
+#define AM33XX_IOPAD(pa, val)		OMAP_IOPAD_OFFSET((pa), 0x0800) (val) (0)
 #define AM33XX_PADCONF(pa, conf, mux)	OMAP_IOPAD_OFFSET((pa), 0x0800) (conf) (mux)
 
 /*