[PATCH] S3C24XX: GPIO based SPI driver
SPI driver for SPI by GPIO on the Samsung S3C24XX series of SoC processors.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 3867c6e..c60dacf 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -95,6 +95,14 @@
The driver can be configured to use any SSP port and additional
documentation can be found a Documentation/spi/pxa2xx.
+config SPI_S3C24XX_GPIO
+ tristate "Samsung S3C24XX series SPI by GPIO"
+ depends on SPI_MASTER && ARCH_S3C2410 && SPI_BITBANG && EXPERIMENTAL
+ help
+ SPI driver for Samsung S3C24XX series ARM SoCs using
+ GPIO lines to provide the SPI bus. This can be used where
+ the inbuilt hardware cannot provide the transfer mode, or
+ where the board is using non hardware connected pins.
#
# Add new SPI master controllers in alphabetical order above this line
#
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 5a410ca..4dc82c9 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -15,6 +15,7 @@
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
obj-$(CONFIG_SPI_MPC83xx) += spi_mpc83xx.o
+obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
# ... add above this line ...
# SPI protocol drivers (device/link on bus)
diff --git a/drivers/spi/spi_butterfly.c b/drivers/spi/spi_butterfly.c
index ff9e5fa..a006a1e 100644
--- a/drivers/spi/spi_butterfly.c
+++ b/drivers/spi/spi_butterfly.c
@@ -321,6 +321,7 @@
* (firmware resets at45, acts as spi slave) or neither (we ignore
* both, AVR uses AT45). Here we expect firmware for the first option.
*/
+
pp->info[0].max_speed_hz = 15 * 1000 * 1000;
strcpy(pp->info[0].modalias, "mtd_dataflash");
pp->info[0].platform_data = &flash;
diff --git a/drivers/spi/spi_s3c24xx_gpio.c b/drivers/spi/spi_s3c24xx_gpio.c
new file mode 100644
index 0000000..aacdceb
--- /dev/null
+++ b/drivers/spi/spi_s3c24xx_gpio.c
@@ -0,0 +1,188 @@
+/* linux/drivers/spi/spi_s3c24xx_gpio.c
+ *
+ * Copyright (c) 2006 Ben Dooks
+ * Copyright (c) 2006 Simtec Electronics
+ *
+ * S3C24XX GPIO based SPI driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/platform_device.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+
+#include <asm/arch/regs-gpio.h>
+#include <asm/arch/spi-gpio.h>
+#include <asm/arch/hardware.h>
+
+struct s3c2410_spigpio {
+ struct spi_bitbang bitbang;
+
+ struct s3c2410_spigpio_info *info;
+ struct platform_device *dev;
+};
+
+static inline struct s3c2410_spigpio *spidev_to_sg(struct spi_device *spi)
+{
+ return spi->controller_data;
+}
+
+static inline void setsck(struct spi_device *dev, int on)
+{
+ struct s3c2410_spigpio *sg = spidev_to_sg(dev);
+ s3c2410_gpio_setpin(sg->info->pin_clk, on ? 1 : 0);
+}
+
+static inline void setmosi(struct spi_device *dev, int on)
+{
+ struct s3c2410_spigpio *sg = spidev_to_sg(dev);
+ s3c2410_gpio_setpin(sg->info->pin_mosi, on ? 1 : 0);
+}
+
+static inline u32 getmiso(struct spi_device *dev)
+{
+ struct s3c2410_spigpio *sg = spidev_to_sg(dev);
+ return s3c2410_gpio_getpin(sg->info->pin_miso) ? 1 : 0;
+}
+
+#define spidelay(x) ndelay(x)
+
+#define EXPAND_BITBANG_TXRX
+#include <linux/spi/spi_bitbang.h>
+
+
+static u32 s3c2410_spigpio_txrx_mode0(struct spi_device *spi,
+ unsigned nsecs, u32 word, u8 bits)
+{
+ return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, bits);
+}
+
+static u32 s3c2410_spigpio_txrx_mode1(struct spi_device *spi,
+ unsigned nsecs, u32 word, u8 bits)
+{
+ return bitbang_txrx_be_cpha1(spi, nsecs, 0, word, bits);
+}
+
+static void s3c2410_spigpio_chipselect(struct spi_device *dev, int value)
+{
+ struct s3c2410_spigpio *sg = spidev_to_sg(dev);
+
+ if (sg->info && sg->info->chip_select)
+ (sg->info->chip_select)(sg->info, value);
+}
+
+static int s3c2410_spigpio_probe(struct platform_device *dev)
+{
+ struct spi_master *master;
+ struct s3c2410_spigpio *sp;
+ int ret;
+ int i;
+
+ master = spi_alloc_master(&dev->dev, sizeof(struct s3c2410_spigpio));
+ if (master == NULL) {
+ dev_err(&dev->dev, "failed to allocate spi master\n");
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ sp = spi_master_get_devdata(master);
+
+ platform_set_drvdata(dev, sp);
+
+ /* copy in the plkatform data */
+ sp->info = dev->dev.platform_data;
+
+ /* setup spi bitbang adaptor */
+ sp->bitbang.master = spi_master_get(master);
+ sp->bitbang.chipselect = s3c2410_spigpio_chipselect;
+
+ sp->bitbang.txrx_word[SPI_MODE_0] = s3c2410_spigpio_txrx_mode0;
+ sp->bitbang.txrx_word[SPI_MODE_1] = s3c2410_spigpio_txrx_mode1;
+
+ /* set state of spi pins */
+ s3c2410_gpio_setpin(sp->info->pin_clk, 0);
+ s3c2410_gpio_setpin(sp->info->pin_mosi, 0);
+
+ s3c2410_gpio_cfgpin(sp->info->pin_clk, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_cfgpin(sp->info->pin_mosi, S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_cfgpin(sp->info->pin_miso, S3C2410_GPIO_INPUT);
+
+ ret = spi_bitbang_start(&sp->bitbang);
+ if (ret)
+ goto err_no_bitbang;
+
+ /* register the chips to go with the board */
+
+ for (i = 0; i < sp->info->board_size; i++) {
+ dev_info(&dev->dev, "registering %p: %s\n",
+ &sp->info->board_info[i],
+ sp->info->board_info[i].modalias);
+
+ sp->info->board_info[i].controller_data = sp;
+ spi_new_device(master, sp->info->board_info + i);
+ }
+
+ return 0;
+
+ err_no_bitbang:
+ spi_master_put(sp->bitbang.master);
+ err:
+ return ret;
+
+}
+
+static int s3c2410_spigpio_remove(struct platform_device *dev)
+{
+ struct s3c2410_spigpio *sp = platform_get_drvdata(dev);
+
+ spi_bitbang_stop(&sp->bitbang);
+ spi_master_put(sp->bitbang.master);
+
+ return 0;
+}
+
+/* all gpio should be held over suspend/resume, so we should
+ * not need to deal with this
+*/
+
+#define s3c2410_spigpio_suspend NULL
+#define s3c2410_spigpio_resume NULL
+
+
+static struct platform_driver s3c2410_spigpio_drv = {
+ .probe = s3c2410_spigpio_probe,
+ .remove = s3c2410_spigpio_remove,
+ .suspend = s3c2410_spigpio_suspend,
+ .resume = s3c2410_spigpio_resume,
+ .driver = {
+ .name = "s3c24xx-spi-gpio",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init s3c2410_spigpio_init(void)
+{
+ return platform_driver_register(&s3c2410_spigpio_drv);
+}
+
+static void __exit s3c2410_spigpio_exit(void)
+{
+ platform_driver_unregister(&s3c2410_spigpio_drv);
+}
+
+module_init(s3c2410_spigpio_init);
+module_exit(s3c2410_spigpio_exit);
+
+MODULE_DESCRIPTION("S3C24XX SPI Driver");
+MODULE_AUTHOR("Ben Dooks, <ben@simtec.co.uk>");
+MODULE_LICENSE("GPL");
