// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2021, The Linux Foundation. All rights reserved.
 * Copyright (c) 2022, Linaro Limited
 */

#include <dt-bindings/clock/qcom,gcc-sc8280xp.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/interconnect/qcom,sc8280xp.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/phy/phy-qcom-qmp.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/thermal/thermal.h>

/ {
	interrupt-parent = <&intc>;

	#address-cells = <2>;
	#size-cells = <2>;

	clocks {
		xo_board_clk: xo-board-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <32764>;
		};
	};

	cpu0_opp_table: cpu0-opp-table {
		compatible = "operating-points-v2";
		opp-shared;

		opp-300000000 {
			opp-hz = /bits/ 64 <300000000>;
			opp-peak-kBps = <(300000 * 32)>;
		};
		opp-403200000 {
			opp-hz = /bits/ 64 <403200000>;
			opp-peak-kBps = <(384000 * 32)>;
		};
		opp-499200000 {
			opp-hz = /bits/ 64 <499200000>;
			opp-peak-kBps = <(480000 * 32)>;
		};
		opp-595200000 {
			opp-hz = /bits/ 64 <595200000>;
			opp-peak-kBps = <(576000 * 32)>;
		};
		opp-691200000 {
			opp-hz = /bits/ 64 <691200000>;
			opp-peak-kBps = <(672000 * 32)>;
		};
		opp-806400000 {
			opp-hz = /bits/ 64 <806400000>;
			opp-peak-kBps = <(768000 * 32)>;
		};
		opp-902400000 {
			opp-hz = /bits/ 64 <902400000>;
			opp-peak-kBps = <(864000 * 32)>;
		};
		opp-1017600000 {
			opp-hz = /bits/ 64 <1017600000>;
			opp-peak-kBps = <(960000 * 32)>;
		};
		opp-1113600000 {
			opp-hz = /bits/ 64 <1113600000>;
			opp-peak-kBps = <(1075200 * 32)>;
		};
		opp-1209600000 {
			opp-hz = /bits/ 64 <1209600000>;
			opp-peak-kBps = <(1171200 * 32)>;
		};
		opp-1324800000 {
			opp-hz = /bits/ 64 <1324800000>;
			opp-peak-kBps = <(1267200 * 32)>;
		};
		opp-1440000000 {
			opp-hz = /bits/ 64 <1440000000>;
			opp-peak-kBps = <(1363200 * 32)>;
		};
		opp-1555200000 {
			opp-hz = /bits/ 64 <1555200000>;
			opp-peak-kBps = <(1536000 * 32)>;
		};
		opp-1670400000 {
			opp-hz = /bits/ 64 <1670400000>;
			opp-peak-kBps = <(1612800 * 32)>;
		};
		opp-1785600000 {
			opp-hz = /bits/ 64 <1785600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-1881600000 {
			opp-hz = /bits/ 64 <1881600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-1996800000 {
			opp-hz = /bits/ 64 <1996800000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2112000000 {
			opp-hz = /bits/ 64 <2112000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2227200000 {
			opp-hz = /bits/ 64 <2227200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2342400000 {
			opp-hz = /bits/ 64 <2342400000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2438400000 {
			opp-hz = /bits/ 64 <2438400000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
	};

	cpu4_opp_table: cpu4-opp-table {
		compatible = "operating-points-v2";
		opp-shared;

		opp-825600000 {
			opp-hz = /bits/ 64 <825600000>;
			opp-peak-kBps = <(768000 * 32)>;
		};
		opp-940800000 {
			opp-hz = /bits/ 64 <940800000>;
			opp-peak-kBps = <(864000 * 32)>;
		};
		opp-1056000000 {
			opp-hz = /bits/ 64 <1056000000>;
			opp-peak-kBps = <(960000 * 32)>;
		};
		opp-1171200000 {
			opp-hz = /bits/ 64 <1171200000>;
			opp-peak-kBps = <(1171200 * 32)>;
		};
		opp-1286400000 {
			opp-hz = /bits/ 64 <1286400000>;
			opp-peak-kBps = <(1267200 * 32)>;
		};
		opp-1401600000 {
			opp-hz = /bits/ 64 <1401600000>;
			opp-peak-kBps = <(1363200 * 32)>;
		};
		opp-1516800000 {
			opp-hz = /bits/ 64 <1516800000>;
			opp-peak-kBps = <(1459200 * 32)>;
		};
		opp-1632000000 {
			opp-hz = /bits/ 64 <1632000000>;
			opp-peak-kBps = <(1612800 * 32)>;
		};
		opp-1747200000 {
			opp-hz = /bits/ 64 <1747200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-1862400000 {
			opp-hz = /bits/ 64 <1862400000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-1977600000 {
			opp-hz = /bits/ 64 <1977600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2073600000 {
			opp-hz = /bits/ 64 <2073600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2169600000 {
			opp-hz = /bits/ 64 <2169600000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2284800000 {
			opp-hz = /bits/ 64 <2284800000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2400000000 {
			opp-hz = /bits/ 64 <2400000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2496000000 {
			opp-hz = /bits/ 64 <2496000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2592000000 {
			opp-hz = /bits/ 64 <2592000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2688000000 {
			opp-hz = /bits/ 64 <2688000000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2803200000 {
			opp-hz = /bits/ 64 <2803200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2899200000 {
			opp-hz = /bits/ 64 <2899200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
		opp-2995200000 {
			opp-hz = /bits/ 64 <2995200000>;
			opp-peak-kBps = <(1689600 * 32)>;
		};
	};

	cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x0>;
			enable-method = "psci";
			capacity-dmips-mhz = <602>;
			next-level-cache = <&L2_0>;
			power-domains = <&CPU_PD0>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_0: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
				L3_0: l3-cache {
				      compatible = "cache";
				};
			};
		};

		CPU1: cpu@100 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x100>;
			enable-method = "psci";
			capacity-dmips-mhz = <602>;
			next-level-cache = <&L2_100>;
			power-domains = <&CPU_PD1>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_100: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU2: cpu@200 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x200>;
			enable-method = "psci";
			capacity-dmips-mhz = <602>;
			next-level-cache = <&L2_200>;
			power-domains = <&CPU_PD2>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_200: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU3: cpu@300 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x300>;
			enable-method = "psci";
			capacity-dmips-mhz = <602>;
			next-level-cache = <&L2_300>;
			power-domains = <&CPU_PD3>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_300: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU4: cpu@400 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x400>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			next-level-cache = <&L2_400>;
			power-domains = <&CPU_PD4>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_400: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU5: cpu@500 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x500>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			next-level-cache = <&L2_500>;
			power-domains = <&CPU_PD5>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_500: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU6: cpu@600 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x600>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			next-level-cache = <&L2_600>;
			power-domains = <&CPU_PD6>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_600: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		CPU7: cpu@700 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x700>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			next-level-cache = <&L2_700>;
			power-domains = <&CPU_PD7>;
			power-domain-names = "psci";
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
			#cooling-cells = <2>;
			L2_700: l2-cache {
				compatible = "cache";
				next-level-cache = <&L3_0>;
			};
		};

		cpu-map {
			cluster0 {
				core0 {
					cpu = <&CPU0>;
				};

				core1 {
					cpu = <&CPU1>;
				};

				core2 {
					cpu = <&CPU2>;
				};

				core3 {
					cpu = <&CPU3>;
				};

				core4 {
					cpu = <&CPU4>;
				};

				core5 {
					cpu = <&CPU5>;
				};

				core6 {
					cpu = <&CPU6>;
				};

				core7 {
					cpu = <&CPU7>;
				};
			};
		};

		idle-states {
			entry-method = "psci";

			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
				compatible = "arm,idle-state";
				idle-state-name = "little-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <355>;
				exit-latency-us = <909>;
				min-residency-us = <3934>;
				local-timer-stop;
			};

			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
				compatible = "arm,idle-state";
				idle-state-name = "big-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <241>;
				exit-latency-us = <1461>;
				min-residency-us = <4488>;
				local-timer-stop;
			};
		};

		domain-idle-states {
			CLUSTER_SLEEP_0: cluster-sleep-0 {
				compatible = "domain-idle-state";
				idle-state-name = "cluster-power-collapse";
				arm,psci-suspend-param = <0x4100c344>;
				entry-latency-us = <3263>;
				exit-latency-us = <6562>;
				min-residency-us = <9987>;
			};
		};
	};

	firmware {
		scm: scm {
			compatible = "qcom,scm-sc8280xp", "qcom,scm";
		};
	};

	aggre1_noc: interconnect-aggre1-noc {
		compatible = "qcom,sc8280xp-aggre1-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	aggre2_noc: interconnect-aggre2-noc {
		compatible = "qcom,sc8280xp-aggre2-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	clk_virt: interconnect-clk-virt {
		compatible = "qcom,sc8280xp-clk-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	config_noc: interconnect-config-noc {
		compatible = "qcom,sc8280xp-config-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	dc_noc: interconnect-dc-noc {
		compatible = "qcom,sc8280xp-dc-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	gem_noc: interconnect-gem-noc {
		compatible = "qcom,sc8280xp-gem-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	lpass_noc: interconnect-lpass-ag-noc {
		compatible = "qcom,sc8280xp-lpass-ag-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	mc_virt: interconnect-mc-virt {
		compatible = "qcom,sc8280xp-mc-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	mmss_noc: interconnect-mmss-noc {
		compatible = "qcom,sc8280xp-mmss-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	nspa_noc: interconnect-nspa-noc {
		compatible = "qcom,sc8280xp-nspa-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	nspb_noc: interconnect-nspb-noc {
		compatible = "qcom,sc8280xp-nspb-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	system_noc: interconnect-system-noc {
		compatible = "qcom,sc8280xp-system-noc";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	memory@80000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the size */
		reg = <0x0 0x80000000 0x0 0x0>;
	};

	pmu {
		compatible = "arm,armv8-pmuv3";
		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";

		CPU_PD0: cpu0 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD1: cpu1 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD2: cpu2 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD3: cpu3 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD4: cpu4 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD5: cpu5 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD6: cpu6 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD7: cpu7 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CLUSTER_PD: cpu-cluster0 {
			#power-domain-cells = <0>;
			domain-idle-states = <&CLUSTER_SLEEP_0>;
		};
	};

	qup_opp_table_100mhz: qup-100mhz-opp-table {
		compatible = "operating-points-v2";

		opp-75000000 {
			opp-hz = /bits/ 64 <75000000>;
			required-opps = <&rpmhpd_opp_low_svs>;
		};

		opp-100000000 {
			opp-hz = /bits/ 64 <100000000>;
			required-opps = <&rpmhpd_opp_svs>;
		};
	};

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		reserved-region@80000000 {
			reg = <0 0x80000000 0 0x860000>;
			no-map;
		};

		cmd_db: cmd-db-region@80860000 {
			compatible = "qcom,cmd-db";
			reg = <0 0x80860000 0 0x20000>;
			no-map;
		};

		reserved-region@80880000 {
			reg = <0 0x80880000 0 0x80000>;
			no-map;
		};

		smem_mem: smem-region@80900000 {
			compatible = "qcom,smem";
			reg = <0 0x80900000 0 0x200000>;
			no-map;
			hwlocks = <&tcsr_mutex 3>;
		};

		reserved-region@80b00000 {
			reg = <0 0x80b00000 0 0x100000>;
			no-map;
		};

		reserved-region@83b00000 {
			reg = <0 0x83b00000 0 0x1700000>;
			no-map;
		};

		reserved-region@85b00000 {
			reg = <0 0x85b00000 0 0xc00000>;
			no-map;
		};

		pil_adsp_mem: adsp-region@86c00000 {
			reg = <0 0x86c00000 0 0x2000000>;
			no-map;
		};

		pil_nsp0_mem: cdsp0-region@8a100000 {
			reg = <0 0x8a100000 0 0x1e00000>;
			no-map;
		};

		pil_nsp1_mem: cdsp1-region@8c600000 {
			reg = <0 0x8c600000 0 0x1e00000>;
			no-map;
		};

		reserved-region@aeb00000 {
			reg = <0 0xaeb00000 0 0x16600000>;
			no-map;
		};
	};

	smp2p-adsp {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;
		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_LPASS
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		smp2p_adsp_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_adsp_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-nsp0 {
		compatible = "qcom,smp2p";
		qcom,smem = <94>, <432>;
		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_CDSP
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <5>;

		smp2p_nsp0_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_nsp0_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-nsp1 {
		compatible = "qcom,smp2p";
		qcom,smem = <617>, <616>;
		interrupts-extended = <&ipcc IPCC_CLIENT_NSP1
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_NSP1
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <12>;

		smp2p_nsp1_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_nsp1_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc@0 {
		compatible = "simple-bus";
		#address-cells = <2>;
		#size-cells = <2>;
		ranges = <0 0 0 0 0x10 0>;
		dma-ranges = <0 0 0 0 0x10 0>;

		gcc: clock-controller@100000 {
			compatible = "qcom,gcc-sc8280xp";
			reg = <0x0 0x00100000 0x0 0x1f0000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&sleep_clk>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <&usb_0_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <&usb_1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <0>,
				 <&pcie2a_phy>,
				 <&pcie2b_phy>,
				 <&pcie3a_phy>,
				 <&pcie3b_phy>,
				 <&pcie4_phy>,
				 <0>,
				 <0>;
			power-domains = <&rpmhpd SC8280XP_CX>;
		};

		ipcc: mailbox@408000 {
			compatible = "qcom,sc8280xp-ipcc", "qcom,ipcc";
			reg = <0 0x00408000 0 0x1000>;
			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <3>;
			#mbox-cells = <2>;
		};

		qup2: geniqup@8c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x008c0000 0 0x2000>;
			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			iommus = <&apps_smmu 0xa3 0>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			qup2_uart17: serial@884000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00884000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			qup2_i2c5: i2c@894000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};
		};

		qup0: geniqup@9c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x009c0000 0 0x6000>;
			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			iommus = <&apps_smmu 0x563 0>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			qup0_i2c4: i2c@990000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00990000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				#address-cells = <1>;
				#size-cells = <0>;
				power-domains = <&rpmhpd SC8280XP_CX>;
				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				status = "disabled";
			};
		};

		qup1: geniqup@ac0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x00ac0000 0 0x6000>;
			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			iommus = <&apps_smmu 0x83 0>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";
		};

		pcie4: pcie@1c00000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c00000 0x0 0x3000>,
			      <0x0 0x30000000 0x0 0xf1d>,
			      <0x0 0x30000f20 0x0 0xa8>,
			      <0x0 0x30001000 0x0 0x1000>,
			      <0x0 0x30100000 0x0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x30200000 0x0 0x30200000 0x0 0x100000>,
				 <0x02000000 0x0 0x30300000 0x0 0x30300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <6>;
			num-lanes = <1>;

			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_4_AUX_CLK>,
				 <&gcc GCC_PCIE_4_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_4_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_4_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_4_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>,
				 <&gcc GCC_CNOC_PCIE4_QX_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf",
				      "cnoc_qx";

			assigned-clocks = <&gcc GCC_PCIE_4_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_4 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_4 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_4_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_4_GDSC>;

			phys = <&pcie4_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie4_phy: phy@1c06000 {
			compatible = "qcom,sc8280xp-qmp-gen3x1-pcie-phy";
			reg = <0x0 0x01c06000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_4_AUX_CLK>,
				 <&gcc GCC_PCIE_4_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_4_CLKREF_CLK>,
				 <&gcc GCC_PCIE4_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_4_PIPE_CLK>,
				 <&gcc GCC_PCIE_4_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE4_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_4_GDSC>;

			resets = <&gcc GCC_PCIE_4_PHY_BCR>;
			reset-names = "phy";

			#clock-cells = <0>;
			clock-output-names = "pcie_4_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie3b: pcie@1c08000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c08000 0x0 0x3000>,
			      <0x0 0x32000000 0x0 0xf1d>,
			      <0x0 0x32000f20 0x0 0xa8>,
			      <0x0 0x32001000 0x0 0x1000>,
			      <0x0 0x32100000 0x0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x32200000 0x0 0x32200000 0x0 0x100000>,
				 <0x02000000 0x0 0x32300000 0x0 0x32300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <5>;
			num-lanes = <2>;

			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 526 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 527 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 528 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 529 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_3B_AUX_CLK>,
				 <&gcc GCC_PCIE_3B_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3B_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_3B_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_3B_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf";

			assigned-clocks = <&gcc GCC_PCIE_3B_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_3B 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_3B 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_3B_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_3B_GDSC>;

			phys = <&pcie3b_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie3b_phy: phy@1c0e000 {
			compatible = "qcom,sc8280xp-qmp-gen3x2-pcie-phy";
			reg = <0x0 0x01c0e000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_3B_AUX_CLK>,
				 <&gcc GCC_PCIE_3B_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3A3B_CLKREF_CLK>,
				 <&gcc GCC_PCIE3B_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_3B_PIPE_CLK>,
				 <&gcc GCC_PCIE_3B_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE3B_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_3B_GDSC>;

			resets = <&gcc GCC_PCIE_3B_PHY_BCR>;
			reset-names = "phy";

			#clock-cells = <0>;
			clock-output-names = "pcie_3b_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie3a: pcie@1c10000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c10000 0x0 0x3000>,
			      <0x0 0x34000000 0x0 0xf1d>,
			      <0x0 0x34000f20 0x0 0xa8>,
			      <0x0 0x34001000 0x0 0x1000>,
			      <0x0 0x34100000 0x0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x34200000 0x0 0x34200000 0x0 0x100000>,
				 <0x02000000 0x0 0x34300000 0x0 0x34300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <4>;
			num-lanes = <4>;

			interrupts = <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 499 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 542 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 543 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 544 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_3A_AUX_CLK>,
				 <&gcc GCC_PCIE_3A_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3A_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_3A_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_3A_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf";

			assigned-clocks = <&gcc GCC_PCIE_3A_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_3A 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_3A 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_3A_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_3A_GDSC>;

			phys = <&pcie3a_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie3a_phy: phy@1c14000 {
			compatible = "qcom,sc8280xp-qmp-gen3x4-pcie-phy";
			reg = <0x0 0x01c14000 0x0 0x2000>,
			      <0x0 0x01c16000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_3A_AUX_CLK>,
				 <&gcc GCC_PCIE_3A_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3A3B_CLKREF_CLK>,
				 <&gcc GCC_PCIE3A_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_3A_PIPE_CLK>,
				 <&gcc GCC_PCIE_3A_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE3A_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_3A_GDSC>;

			resets = <&gcc GCC_PCIE_3A_PHY_BCR>;
			reset-names = "phy";

			qcom,4ln-config-sel = <&tcsr 0xa044 1>;

			#clock-cells = <0>;
			clock-output-names = "pcie_3a_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie2b: pcie@1c18000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c18000 0x0 0x3000>,
			      <0x0 0x38000000 0x0 0xf1d>,
			      <0x0 0x38000f20 0x0 0xa8>,
			      <0x0 0x38001000 0x0 0x1000>,
			      <0x0 0x38100000 0x0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x38200000 0x0 0x38200000 0x0 0x100000>,
				 <0x02000000 0x0 0x38300000 0x0 0x38300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <3>;
			num-lanes = <2>;

			interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 434 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_2B_AUX_CLK>,
				 <&gcc GCC_PCIE_2B_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2B_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_2B_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_2B_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf";

			assigned-clocks = <&gcc GCC_PCIE_2B_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_2B 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_2B 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_2B_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_2B_GDSC>;

			phys = <&pcie2b_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie2b_phy: phy@1c1e000 {
			compatible = "qcom,sc8280xp-qmp-gen3x2-pcie-phy";
			reg = <0x0 0x01c1e000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_2B_AUX_CLK>,
				 <&gcc GCC_PCIE_2B_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2A2B_CLKREF_CLK>,
				 <&gcc GCC_PCIE2B_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_2B_PIPE_CLK>,
				 <&gcc GCC_PCIE_2B_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE2B_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_2B_GDSC>;

			resets = <&gcc GCC_PCIE_2B_PHY_BCR>;
			reset-names = "phy";

			#clock-cells = <0>;
			clock-output-names = "pcie_2b_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie2a: pcie@1c20000 {
			device_type = "pci";
			compatible = "qcom,pcie-sc8280xp";
			reg = <0x0 0x01c20000 0x0 0x3000>,
			      <0x0 0x3c000000 0x0 0xf1d>,
			      <0x0 0x3c000f20 0x0 0xa8>,
			      <0x0 0x3c001000 0x0 0x1000>,
			      <0x0 0x3c100000 0x0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			#address-cells = <3>;
			#size-cells = <2>;
			ranges = <0x01000000 0x0 0x3c200000 0x0 0x3c200000 0x0 0x100000>,
				 <0x02000000 0x0 0x3c300000 0x0 0x3c300000 0x0 0x1d00000>;
			bus-range = <0x00 0xff>;

			dma-coherent;

			linux,pci-domain = <2>;
			num-lanes = <4>;

			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 523 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 524 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 525 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 2 &intc 0 0 GIC_SPI 531 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 3 &intc 0 0 GIC_SPI 532 IRQ_TYPE_LEVEL_HIGH>,
					<0 0 0 4 &intc 0 0 GIC_SPI 533 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_PCIE_2A_AUX_CLK>,
				 <&gcc GCC_PCIE_2A_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2A_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_2A_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_2A_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_4_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_SOUTH_SF_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ddrss_sf_tbu",
				      "noc_aggr_4",
				      "noc_aggr_south_sf";

			assigned-clocks = <&gcc GCC_PCIE_2A_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			interconnects = <&aggre2_noc MASTER_PCIE_2A 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_2A 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			resets = <&gcc GCC_PCIE_2A_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_2A_GDSC>;

			phys = <&pcie2a_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie2a_phy: phy@1c24000 {
			compatible = "qcom,sc8280xp-qmp-gen3x4-pcie-phy";
			reg = <0x0 0x01c24000 0x0 0x2000>,
			      <0x0 0x01c26000 0x0 0x2000>;

			clocks = <&gcc GCC_PCIE_2A_AUX_CLK>,
				 <&gcc GCC_PCIE_2A_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2A2B_CLKREF_CLK>,
				 <&gcc GCC_PCIE2A_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_2A_PIPE_CLK>,
				 <&gcc GCC_PCIE_2A_PIPEDIV2_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng",
				      "pipe", "pipediv2";

			assigned-clocks = <&gcc GCC_PCIE2A_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			power-domains = <&gcc PCIE_2A_GDSC>;

			resets = <&gcc GCC_PCIE_2A_PHY_BCR>;
			reset-names = "phy";

			qcom,4ln-config-sel = <&tcsr 0xa044 0>;

			#clock-cells = <0>;
			clock-output-names = "pcie_2a_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		ufs_mem_hc: ufs@1d84000 {
			compatible = "qcom,sc8280xp-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0 0x01d84000 0 0x3000>;
			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_mem_phy>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_PHY_BCR>;
			reset-names = "rst";

			power-domains = <&gcc UFS_PHY_GDSC>;
			required-opps = <&rpmhpd_opp_nom>;

			iommus = <&apps_smmu 0xe0 0x0>;
			dma-coherent;

			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_UFS_PHY_AHB_CLK>,
				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
				 <&gcc GCC_UFS_REF_CLKREF_CLK>,
				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
			clock-names = "core_clk",
				      "bus_aggr_clk",
				      "iface_clk",
				      "core_clk_unipro",
				      "ref_clk",
				      "tx_lane0_sync_clk",
				      "rx_lane0_sync_clk",
				      "rx_lane1_sync_clk";
			freq-table-hz = <75000000 300000000>,
					<0 0>,
					<0 0>,
					<75000000 300000000>,
					<0 0>,
					<0 0>,
					<0 0>,
					<0 0>;
			status = "disabled";
		};

		ufs_mem_phy: phy@1d87000 {
			compatible = "qcom,sc8280xp-qmp-ufs-phy";
			reg = <0 0x01d87000 0 0x1000>;

			clocks = <&gcc GCC_UFS_CARD_CLKREF_CLK>,
				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
			clock-names = "ref", "ref_aux";

			power-domains = <&gcc UFS_PHY_GDSC>;

			resets = <&ufs_mem_hc 0>;
			reset-names = "ufsphy";

			#phy-cells = <0>;

			status = "disabled";
		};

		ufs_card_hc: ufs@1da4000 {
			compatible = "qcom,sc8280xp-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0 0x01da4000 0 0x3000>;
			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_card_phy>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_CARD_BCR>;
			reset-names = "rst";

			power-domains = <&gcc UFS_CARD_GDSC>;

			iommus = <&apps_smmu 0x4a0 0x0>;
			dma-coherent;

			clocks = <&gcc GCC_UFS_CARD_AXI_CLK>,
				 <&gcc GCC_AGGRE_UFS_CARD_AXI_CLK>,
				 <&gcc GCC_UFS_CARD_AHB_CLK>,
				 <&gcc GCC_UFS_CARD_UNIPRO_CORE_CLK>,
				 <&gcc GCC_UFS_REF_CLKREF_CLK>,
				 <&gcc GCC_UFS_CARD_TX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_CARD_RX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_CARD_RX_SYMBOL_1_CLK>;
			clock-names = "core_clk",
				      "bus_aggr_clk",
				      "iface_clk",
				      "core_clk_unipro",
				      "ref_clk",
				      "tx_lane0_sync_clk",
				      "rx_lane0_sync_clk",
				      "rx_lane1_sync_clk";
			freq-table-hz = <75000000 300000000>,
					<0 0>,
					<0 0>,
					<75000000 300000000>,
					<0 0>,
					<0 0>,
					<0 0>,
					<0 0>;
			status = "disabled";
		};

		ufs_card_phy: phy@1da7000 {
			compatible = "qcom,sc8280xp-qmp-ufs-phy";
			reg = <0 0x01da7000 0 0x1000>;

			clocks = <&gcc GCC_UFS_1_CARD_CLKREF_CLK>,
				 <&gcc GCC_UFS_CARD_PHY_AUX_CLK>;
			clock-names = "ref", "ref_aux";

			power-domains = <&gcc UFS_CARD_GDSC>;

			resets = <&ufs_card_hc 0>;
			reset-names = "ufsphy";

			#phy-cells = <0>;

			status = "disabled";
		};

		tcsr_mutex: hwlock@1f40000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0x0 0x01f40000 0x0 0x20000>;
			#hwlock-cells = <1>;
		};

		tcsr: syscon@1fc0000 {
			compatible = "qcom,sc8280xp-tcsr", "syscon";
			reg = <0x0 0x01fc0000 0x0 0x30000>;
		};

		usb_0_hsphy: phy@88e5000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088e5000 0 0x400>;
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_hsphy0: phy@88e7000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088e7000 0 0x400>;
			clocks = <&gcc GCC_USB2_HS0_CLKREF_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_HS0_MP_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_hsphy1: phy@88e8000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088e8000 0 0x400>;
			clocks = <&gcc GCC_USB2_HS1_CLKREF_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_HS1_MP_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_hsphy2: phy@88e9000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088e9000 0 0x400>;
			clocks = <&gcc GCC_USB2_HS2_CLKREF_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_HS2_MP_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_hsphy3: phy@88ea000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x088ea000 0 0x400>;
			clocks = <&gcc GCC_USB2_HS3_CLKREF_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_HS3_MP_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_qmpphy0: phy@88ef000 {
			compatible = "qcom,sc8280xp-qmp-usb3-uni-phy";
			reg = <0 0x088ef000 0 0x2000>;

			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
				 <&gcc GCC_USB3_MP0_CLKREF_CLK>,
				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>;
			clock-names = "aux", "ref", "com_aux", "pipe";

			resets = <&gcc GCC_USB3_UNIPHY_MP0_BCR>,
				 <&gcc GCC_USB3UNIPHY_PHY_MP0_BCR>;
			reset-names = "phy", "phy_phy";

			power-domains = <&gcc USB30_MP_GDSC>;

			#clock-cells = <0>;
			clock-output-names = "usb2_phy0_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_2_qmpphy1: phy@88f1000 {
			compatible = "qcom,sc8280xp-qmp-usb3-uni-phy";
			reg = <0 0x088f1000 0 0x2000>;

			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
				 <&gcc GCC_USB3_MP1_CLKREF_CLK>,
				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_MP_PHY_PIPE_1_CLK>;
			clock-names = "aux", "ref", "com_aux", "pipe";

			resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>,
				 <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>;
			reset-names = "phy", "phy_phy";

			power-domains = <&gcc USB30_MP_GDSC>;

			#clock-cells = <0>;
			clock-output-names = "usb2_phy1_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		remoteproc_adsp: remoteproc@3000000 {
			compatible = "qcom,sc8280xp-adsp-pas";
			reg = <0 0x03000000 0 0x100>;

			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 7 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack", "shutdown-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8280XP_LCX>,
					<&rpmhpd SC8280XP_LMX>;
			power-domain-names = "lcx", "lmx";

			memory-region = <&pil_adsp_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_adsp_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			remoteproc_adsp_glink: glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_LPASS
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "lpass";
				qcom,remote-pid = <2>;
			};
		};

		usb_0_qmpphy: phy@88eb000 {
			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
			reg = <0 0x088eb000 0 0x4000>;

			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
				 <&gcc GCC_USB4_EUD_CLKREF_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
			clock-names = "aux", "ref", "com_aux", "usb3_pipe";

			power-domains = <&gcc USB30_PRIM_GDSC>;

			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
				 <&gcc GCC_USB4_DP_PHY_PRIM_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#phy-cells = <1>;

			status = "disabled";
		};

		usb_1_hsphy: phy@8902000 {
			compatible = "qcom,sc8280xp-usb-hs-phy",
				     "qcom,usb-snps-hs-5nm-phy";
			reg = <0 0x08902000 0 0x400>;
			#phy-cells = <0>;

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";

			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;

			status = "disabled";
		};

		usb_1_qmpphy: phy@8903000 {
			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
			reg = <0 0x08903000 0 0x4000>;

			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
				 <&gcc GCC_USB4_CLKREF_CLK>,
				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
			clock-names = "aux", "ref", "com_aux", "usb3_pipe";

			power-domains = <&gcc USB30_SEC_GDSC>;

			resets = <&gcc GCC_USB3_PHY_SEC_BCR>,
				 <&gcc GCC_USB4_1_DP_PHY_PRIM_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#phy-cells = <1>;

			status = "disabled";
		};

		pmu@9091000 {
			compatible = "qcom,sc8280xp-llcc-bwmon", "qcom,sc7280-llcc-bwmon";
			reg = <0 0x9091000 0 0x1000>;

			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;

			interconnects = <&mc_virt MASTER_LLCC 3 &mc_virt SLAVE_EBI1 3>;

			operating-points-v2 = <&llcc_bwmon_opp_table>;

			llcc_bwmon_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-0 {
					opp-peak-kBps = <762000>;
				};
				opp-1 {
					opp-peak-kBps = <1720000>;
				};
				opp-2 {
					opp-peak-kBps = <2086000>;
				};
				opp-3 {
					opp-peak-kBps = <2597000>;
				};
				opp-4 {
					opp-peak-kBps = <2929000>;
				};
				opp-5 {
					opp-peak-kBps = <3879000>;
				};
				opp-6 {
					opp-peak-kBps = <5161000>;
				};
				opp-7 {
					opp-peak-kBps = <5931000>;
				};
				opp-8 {
					opp-peak-kBps = <6515000>;
				};
				opp-9 {
					opp-peak-kBps = <7980000>;
				};
				opp-10 {
					opp-peak-kBps = <8136000>;
				};
				opp-11 {
					opp-peak-kBps = <10437000>;
				};
				opp-12 {
					opp-peak-kBps = <12191000>;
				};
			};
		};

		pmu@90b6400 {
			compatible = "qcom,sc8280xp-cpu-bwmon", "qcom,msm8998-bwmon";
			reg = <0 0x090b6400 0 0x600>;

			interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;

			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &gem_noc SLAVE_LLCC 3>;
			operating-points-v2 = <&cpu_bwmon_opp_table>;

			cpu_bwmon_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-0 {
					opp-peak-kBps = <2288000>;
				};
				opp-1 {
					opp-peak-kBps = <4577000>;
				};
				opp-2 {
					opp-peak-kBps = <7110000>;
				};
				opp-3 {
					opp-peak-kBps = <9155000>;
				};
				opp-4 {
					opp-peak-kBps = <12298000>;
				};
				opp-5 {
					opp-peak-kBps = <14236000>;
				};
				opp-6 {
					opp-peak-kBps = <15258001>;
				};
			};
		};

		system-cache-controller@9200000 {
			compatible = "qcom,sc8280xp-llcc";
			reg = <0 0x09200000 0 0x58000>, <0 0x09600000 0 0x58000>;
			reg-names = "llcc_base", "llcc_broadcast_base";
			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
		};

		usb_0: usb@a6f8800 {
			compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
			reg = <0 0x0a6f8800 0 0x400>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";

			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 804 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 138 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "pwr_event",
					  "dp_hs_phy_irq",
					  "dm_hs_phy_irq",
					  "ss_phy_irq";

			power-domains = <&gcc USB30_PRIM_GDSC>;

			resets = <&gcc GCC_USB30_PRIM_BCR>;

			interconnects = <&aggre1_noc MASTER_USB3_0 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			wakeup-source;

			status = "disabled";

			usb_0_dwc3: usb@a600000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a600000 0 0xcd00>;
				interrupts = <GIC_SPI 803 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x820 0x0>;
				phys = <&usb_0_hsphy>, <&usb_0_qmpphy QMP_USB43DP_USB3_PHY>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		usb_1: usb@a8f8800 {
			compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
			reg = <0 0x0a8f8800 0 0x400>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
				 <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";

			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 811 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 136 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "pwr_event",
					  "dp_hs_phy_irq",
					  "dm_hs_phy_irq",
					  "ss_phy_irq";

			power-domains = <&gcc USB30_SEC_GDSC>;

			resets = <&gcc GCC_USB30_SEC_BCR>;

			interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			wakeup-source;

			status = "disabled";

			usb_1_dwc3: usb@a800000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a800000 0 0xcd00>;
				interrupts = <GIC_SPI 810 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x860 0x0>;
				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		pdc: interrupt-controller@b220000 {
			compatible = "qcom,sc8280xp-pdc", "qcom,pdc";
			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
			qcom,pdc-ranges = <0 480 40>,
					  <40 140 14>,
					  <54 263 1>,
					  <55 306 4>,
					  <59 312 3>,
					  <62 374 2>,
					  <64 434 2>,
					  <66 438 3>,
					  <69 86 1>,
					  <70 520 54>,
					  <124 609 28>,
					  <159 638 1>,
					  <160 720 8>,
					  <168 801 1>,
					  <169 728 30>,
					  <199 416 2>,
					  <201 449 1>,
					  <202 89 1>,
					  <203 451 1>,
					  <204 462 1>,
					  <205 264 1>,
					  <206 579 1>,
					  <207 653 1>,
					  <208 656 1>,
					  <209 659 1>,
					  <210 122 1>,
					  <211 699 1>,
					  <212 705 1>,
					  <213 450 1>,
					  <214 643 1>,
					  <216 646 5>,
					  <221 390 5>,
					  <226 700 3>,
					  <229 240 3>,
					  <232 269 1>,
					  <233 377 1>,
					  <234 372 1>,
					  <235 138 1>,
					  <236 857 1>,
					  <237 860 1>,
					  <238 137 1>,
					  <239 668 1>,
					  <240 366 1>,
					  <241 949 1>,
					  <242 815 5>,
					  <247 769 1>,
					  <248 768 1>,
					  <249 663 1>,
					  <250 799 2>,
					  <252 798 1>,
					  <253 765 1>,
					  <254 763 1>,
					  <255 454 1>,
					  <258 139 1>,
					  <259 786 2>,
					  <261 370 2>,
					  <263 158 2>;
			#interrupt-cells = <2>;
			interrupt-parent = <&intc>;
			interrupt-controller;
		};

		tsens0: thermal-sensor@c263000 {
			compatible = "qcom,sc8280xp-tsens", "qcom,tsens-v2";
			reg = <0 0x0c263000 0 0x1ff>, /* TM */
			      <0 0x0c222000 0 0x8>; /* SROT */
			#qcom,sensors = <14>;
			interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens1: thermal-sensor@c265000 {
			compatible = "qcom,sc8280xp-tsens", "qcom,tsens-v2";
			reg = <0 0x0c265000 0 0x1ff>, /* TM */
			      <0 0x0c223000 0 0x8>; /* SROT */
			#qcom,sensors = <16>;
			interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		aoss_qmp: power-controller@c300000 {
			compatible = "qcom,sc8280xp-aoss-qmp", "qcom,aoss-qmp";
			reg = <0 0x0c300000 0 0x400>;
			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP IRQ_TYPE_EDGE_RISING>;
			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;

			#clock-cells = <0>;
		};

		sram@c3f0000 {
			compatible = "qcom,rpmh-stats";
			reg = <0 0x0c3f0000 0 0x400>;
		};

		spmi_bus: spmi@c440000 {
			compatible = "qcom,spmi-pmic-arb";
			reg = <0 0x0c440000 0 0x1100>,
			      <0 0x0c600000 0 0x2000000>,
			      <0 0x0e600000 0 0x100000>,
			      <0 0x0e700000 0 0xa0000>,
			      <0 0x0c40a000 0 0x26000>;
			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
			interrupt-names = "periph_irq";
			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			#address-cells = <1>;
			#size-cells = <1>;
			interrupt-controller;
			#interrupt-cells = <4>;
		};

		tlmm: pinctrl@f100000 {
			compatible = "qcom,sc8280xp-tlmm";
			reg = <0 0x0f100000 0 0x300000>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			gpio-ranges = <&tlmm 0 0 230>;
		};

		apps_smmu: iommu@15000000 {
			compatible = "qcom,sc8280xp-smmu-500", "arm,mmu-500";
			reg = <0 0x15000000 0 0x100000>;
			#iommu-cells = <2>;
			#global-interrupts = <2>;
			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 706 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 689 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 708 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 709 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 710 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 711 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 712 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 713 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 714 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 715 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 912 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 911 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 910 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 909 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 908 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 907 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 906 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 905 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 904 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 903 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 902 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 901 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 900 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 899 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 898 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 895 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 894 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 893 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 892 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 891 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 890 IRQ_TYPE_LEVEL_HIGH>;
		};

		intc: interrupt-controller@17a00000 {
			compatible = "arm,gic-v3";
			interrupt-controller;
			#interrupt-cells = <3>;
			reg = <0x0 0x17a00000 0x0 0x10000>,	/* GICD */
			      <0x0 0x17a60000 0x0 0x100000>;	/* GICR * 8 */
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
			#redistributor-regions = <1>;
			redistributor-stride = <0 0x20000>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			gic-its@17a40000 {
				compatible = "arm,gic-v3-its";
				reg = <0 0x17a40000 0 0x20000>;
				msi-controller;
				#msi-cells = <1>;
			};
		};

		watchdog@17c10000 {
			compatible = "qcom,apss-wdt-sc8280xp", "qcom,kpss-wdt";
			reg = <0 0x17c10000 0 0x1000>;
			clocks = <&sleep_clk>;
			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
		};

		timer@17c20000 {
			compatible = "arm,armv7-timer-mem";
			reg = <0x0 0x17c20000 0x0 0x1000>;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x0 0x0 0x20000000>;

			frame@17c21000 {
				frame-number = <0>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c21000 0x1000>,
				      <0x17c22000 0x1000>;
			};

			frame@17c23000 {
				frame-number = <1>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c23000 0x1000>;
				status = "disabled";
			};

			frame@17c25000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c25000 0x1000>;
				status = "disabled";
			};

			frame@17c27000 {
				frame-number = <3>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c26000 0x1000>;
				status = "disabled";
			};

			frame@17c29000 {
				frame-number = <4>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c29000 0x1000>;
				status = "disabled";
			};

			frame@17c2b000 {
				frame-number = <5>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c2b000 0x1000>;
				status = "disabled";
			};

			frame@17c2d000 {
				frame-number = <6>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c2d000 0x1000>;
				status = "disabled";
			};
		};

		apps_rsc: rsc@18200000 {
			compatible = "qcom,rpmh-rsc";
			reg = <0x0 0x18200000 0x0 0x10000>,
				<0x0 0x18210000 0x0 0x10000>,
				<0x0 0x18220000 0x0 0x10000>;
			reg-names = "drv-0", "drv-1", "drv-2";
			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0xd00>;
			qcom,drv-id = <2>;
			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   3>,
					  <WAKE_TCS    3>, <CONTROL_TCS 1>;
			label = "apps_rsc";

			apps_bcm_voter: bcm-voter {
				compatible = "qcom,bcm-voter";
			};

			rpmhcc: clock-controller {
				compatible = "qcom,sc8280xp-rpmh-clk";
				#clock-cells = <1>;
				clock-names = "xo";
				clocks = <&xo_board_clk>;
			};

			rpmhpd: power-controller {
				compatible = "qcom,sc8280xp-rpmhpd";
				#power-domain-cells = <1>;
				operating-points-v2 = <&rpmhpd_opp_table>;

				rpmhpd_opp_table: opp-table {
					compatible = "operating-points-v2";

					rpmhpd_opp_ret: opp1 {
						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
					};

					rpmhpd_opp_min_svs: opp2 {
						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
					};

					rpmhpd_opp_low_svs: opp3 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					};

					rpmhpd_opp_svs: opp4 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					};

					rpmhpd_opp_svs_l1: opp5 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					};

					rpmhpd_opp_nom: opp6 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					};

					rpmhpd_opp_nom_l1: opp7 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					};

					rpmhpd_opp_nom_l2: opp8 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
					};

					rpmhpd_opp_turbo: opp9 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					};

					rpmhpd_opp_turbo_l1: opp10 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					};
				};
			};
		};

		epss_l3: interconnect@18590000 {
			compatible = "qcom,sc8280xp-epss-l3", "qcom,epss-l3";
			reg = <0 0x18590000 0 0x1000>;

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
			clock-names = "xo", "alternate";

			#interconnect-cells = <1>;
		};

		cpufreq_hw: cpufreq@18591000 {
			compatible = "qcom,sc8280xp-cpufreq-epss", "qcom,cpufreq-epss";
			reg = <0 0x18591000 0 0x1000>,
			      <0 0x18592000 0 0x1000>;
			reg-names = "freq-domain0", "freq-domain1";

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
			clock-names = "xo", "alternate";

			#freq-domain-cells = <1>;
		};

		remoteproc_nsp0: remoteproc@1b300000 {
			compatible = "qcom,sc8280xp-nsp0-pas";
			reg = <0 0x1b300000 0 0x100>;

			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_nsp0_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp0_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp0_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp0_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8280XP_NSP>;
			power-domain-names = "nsp";

			memory-region = <&pil_nsp0_mem>;

			qcom,smem-states = <&smp2p_nsp0_out 0>;
			qcom,smem-state-names = "stop";

			interconnects = <&nspa_noc MASTER_CDSP_PROC 0 &mc_virt SLAVE_EBI1 0>;

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_CDSP
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "nsp0";
				qcom,remote-pid = <5>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "cdsp";
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@1 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <1>;
						iommus = <&apps_smmu 0x3181 0x0420>;
					};

					compute-cb@2 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <2>;
						iommus = <&apps_smmu 0x3182 0x0420>;
					};

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x3183 0x0420>;
					};

					compute-cb@4 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <4>;
						iommus = <&apps_smmu 0x3184 0x0420>;
					};

					compute-cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&apps_smmu 0x3185 0x0420>;
					};

					compute-cb@6 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <6>;
						iommus = <&apps_smmu 0x3186 0x0420>;
					};

					compute-cb@7 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <7>;
						iommus = <&apps_smmu 0x3187 0x0420>;
					};

					compute-cb@8 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <8>;
						iommus = <&apps_smmu 0x3188 0x0420>;
					};

					compute-cb@9 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <9>;
						iommus = <&apps_smmu 0x318b 0x0420>;
					};

					compute-cb@10 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <10>;
						iommus = <&apps_smmu 0x318b 0x0420>;
					};

					compute-cb@11 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <11>;
						iommus = <&apps_smmu 0x318c 0x0420>;
					};

					compute-cb@12 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <12>;
						iommus = <&apps_smmu 0x318d 0x0420>;
					};

					compute-cb@13 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <13>;
						iommus = <&apps_smmu 0x318e 0x0420>;
					};

					compute-cb@14 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <14>;
						iommus = <&apps_smmu 0x318f 0x0420>;
					};
				};
			};
		};

		remoteproc_nsp1: remoteproc@21300000 {
			compatible = "qcom,sc8280xp-nsp1-pas";
			reg = <0 0x21300000 0 0x100>;

			interrupts-extended = <&intc GIC_SPI 887 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_nsp1_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp1_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp1_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_nsp1_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8280XP_NSP>;
			power-domain-names = "nsp";

			memory-region = <&pil_nsp1_mem>;

			qcom,smem-states = <&smp2p_nsp1_out 0>;
			qcom,smem-state-names = "stop";

			interconnects = <&nspb_noc MASTER_CDSP_PROC_B 0 &mc_virt SLAVE_EBI1 0>;

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_NSP1
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_NSP1
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "nsp1";
				qcom,remote-pid = <12>;
			};
		};
	};

	thermal-zones {
		cpu0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 1>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 2>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 3>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu3-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 4>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu4-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 5>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu5-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 6>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu6-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 7>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu7-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 8>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cluster0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 9>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		mem-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 15>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
	};
};