ide: add ide_set{_max}_pio() (take 4)
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index 37ecd72..005402a 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -283,17 +283,14 @@
#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
/**
- * ali15x3_tune_pio - set up chipset for PIO mode
- * @drive: drive to tune
- * @pio: desired mode
+ * ali_tune_pio - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
- * Select the best PIO mode for the drive in question.
- * Then program the controller for this mode.
- *
- * Returns the PIO mode programmed.
+ * Program the controller for the given PIO mode.
*/
-
-static u8 ali15x3_tune_pio (ide_drive_t *drive, u8 pio)
+
+static void ali_tune_pio(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -306,7 +303,6 @@
u8 cd_dma_fifo = 0;
int unit = drive->select.b.unit & 1;
- pio = ide_get_best_pio_mode(drive, pio, 5);
s_time = ide_pio_timings[pio].setup_time;
a_time = ide_pio_timings[pio].active_time;
if ((s_clc = (s_time * bus_speed + 999) / 1000) >= 8)
@@ -359,22 +355,20 @@
* { 25, 70, 25 }, PIO Mode 4 with IORDY ns
* { 20, 50, 30 } PIO Mode 5 with IORDY (nonstandard)
*/
-
- return pio;
}
/**
- * ali15x3_tune_drive - set up drive for PIO mode
+ * ali_set_pio_mode - set up drive for PIO mode
* @drive: drive to tune
* @pio: desired mode
*
- * Program the controller with the best PIO timing for the given drive.
+ * Program the controller with the desired PIO timing for the given drive.
* Then set up the drive itself.
*/
-static void ali15x3_tune_drive (ide_drive_t *drive, u8 pio)
+static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pio = ali15x3_tune_pio(drive, pio);
+ ali_tune_pio(drive, pio);
(void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
@@ -437,7 +431,7 @@
pci_write_config_byte(dev, m5229_udma, tmpbyte);
if (speed < XFER_SW_DMA_0)
- (void) ali15x3_tune_pio(drive, speed - XFER_PIO_0);
+ ali_tune_pio(drive, speed - XFER_PIO_0);
} else {
pci_read_config_byte(dev, m5229_udma, &tmpbyte);
tmpbyte &= (0x0f << ((1-unit) << 2));
@@ -470,7 +464,7 @@
if (ide_tune_dma(drive))
return 0;
- ali15x3_tune_drive(drive, 255);
+ ide_set_max_pio(drive);
return -1;
}
@@ -700,7 +694,7 @@
static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
{
hwif->autodma = 0;
- hwif->tuneproc = &ali15x3_tune_drive;
+ hwif->set_pio_mode = &ali_set_pio_mode;
hwif->speedproc = &ali15x3_tune_chipset;
hwif->udma_filter = &ali_udma_filter;
