ice: Use the proto argument for VLAN ops
Currently the proto argument is unused. This is because the driver only
supports 802.1Q VLAN filtering. This policy is enforced via netdev
features that the driver sets up when configuring the netdev, so the
proto argument won't ever be anything other than 802.1Q. However, this
will allow for future iterations of the driver to seemlessly support
802.1ad filtering. Begin using the proto argument and extend the related
structures to support its use.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
diff --git a/drivers/net/ethernet/intel/ice/ice_main.c b/drivers/net/ethernet/intel/ice/ice_main.c
index cc13943..8ec36bd 100644
--- a/drivers/net/ethernet/intel/ice/ice_main.c
+++ b/drivers/net/ethernet/intel/ice/ice_main.c
@@ -3402,14 +3402,13 @@ ice_lb_vsi_setup(struct ice_pf *pf, struct ice_port_info *pi)
/**
* ice_vlan_rx_add_vid - Add a VLAN ID filter to HW offload
* @netdev: network interface to be adjusted
- * @proto: unused protocol
+ * @proto: VLAN TPID
* @vid: VLAN ID to be added
*
* net_device_ops implementation for adding VLAN IDs
*/
static int
-ice_vlan_rx_add_vid(struct net_device *netdev, __always_unused __be16 proto,
- u16 vid)
+ice_vlan_rx_add_vid(struct net_device *netdev, __be16 proto, u16 vid)
{
struct ice_netdev_priv *np = netdev_priv(netdev);
struct ice_vsi *vsi = np->vsi;
@@ -3430,7 +3429,7 @@ ice_vlan_rx_add_vid(struct net_device *netdev, __always_unused __be16 proto,
/* Add a switch rule for this VLAN ID so its corresponding VLAN tagged
* packets aren't pruned by the device's internal switch on Rx
*/
- vlan = ICE_VLAN(vid, 0);
+ vlan = ICE_VLAN(be16_to_cpu(proto), vid, 0);
ret = vsi->vlan_ops.add_vlan(vsi, &vlan);
if (!ret)
set_bit(ICE_VSI_VLAN_FLTR_CHANGED, vsi->state);
@@ -3441,14 +3440,13 @@ ice_vlan_rx_add_vid(struct net_device *netdev, __always_unused __be16 proto,
/**
* ice_vlan_rx_kill_vid - Remove a VLAN ID filter from HW offload
* @netdev: network interface to be adjusted
- * @proto: unused protocol
+ * @proto: VLAN TPID
* @vid: VLAN ID to be removed
*
* net_device_ops implementation for removing VLAN IDs
*/
static int
-ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto,
- u16 vid)
+ice_vlan_rx_kill_vid(struct net_device *netdev, __be16 proto, u16 vid)
{
struct ice_netdev_priv *np = netdev_priv(netdev);
struct ice_vsi *vsi = np->vsi;
@@ -3462,7 +3460,7 @@ ice_vlan_rx_kill_vid(struct net_device *netdev, __always_unused __be16 proto,
/* Make sure VLAN delete is successful before updating VLAN
* information
*/
- vlan = ICE_VLAN(vid, 0);
+ vlan = ICE_VLAN(be16_to_cpu(proto), vid, 0);
ret = vsi->vlan_ops.del_vlan(vsi, &vlan);
if (ret)
return ret;
@@ -5608,14 +5606,14 @@ ice_set_features(struct net_device *netdev, netdev_features_t features)
if ((features & NETIF_F_HW_VLAN_CTAG_RX) &&
!(netdev->features & NETIF_F_HW_VLAN_CTAG_RX))
- ret = vsi->vlan_ops.ena_stripping(vsi);
+ ret = vsi->vlan_ops.ena_stripping(vsi, ETH_P_8021Q);
else if (!(features & NETIF_F_HW_VLAN_CTAG_RX) &&
(netdev->features & NETIF_F_HW_VLAN_CTAG_RX))
ret = vsi->vlan_ops.dis_stripping(vsi);
if ((features & NETIF_F_HW_VLAN_CTAG_TX) &&
!(netdev->features & NETIF_F_HW_VLAN_CTAG_TX))
- ret = vsi->vlan_ops.ena_insertion(vsi);
+ ret = vsi->vlan_ops.ena_insertion(vsi, ETH_P_8021Q);
else if (!(features & NETIF_F_HW_VLAN_CTAG_TX) &&
(netdev->features & NETIF_F_HW_VLAN_CTAG_TX))
ret = vsi->vlan_ops.dis_insertion(vsi);
@@ -5661,9 +5659,9 @@ static int ice_vsi_vlan_setup(struct ice_vsi *vsi)
int ret = 0;
if (vsi->netdev->features & NETIF_F_HW_VLAN_CTAG_RX)
- ret = vsi->vlan_ops.ena_stripping(vsi);
+ ret = vsi->vlan_ops.ena_stripping(vsi, ETH_P_8021Q);
if (vsi->netdev->features & NETIF_F_HW_VLAN_CTAG_TX)
- ret = vsi->vlan_ops.ena_insertion(vsi);
+ ret = vsi->vlan_ops.ena_insertion(vsi, ETH_P_8021Q);
return ret;
}
