net: vxge: Fix some indentation issues
Some statements are not enough or too much indented.
Fix it to improve readalbility.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/neterion/vxge/vxge-main.c b/drivers/net/ethernet/neterion/vxge/vxge-main.c
index fe7e0e1..b2299f2 100644
--- a/drivers/net/ethernet/neterion/vxge/vxge-main.c
+++ b/drivers/net/ethernet/neterion/vxge/vxge-main.c
@@ -1530,7 +1530,7 @@ static int vxge_reset_vpath(struct vxgedev *vdev, int vp_id)
vxge_debug_init(VXGE_ERR,
"vxge_hw_vpath_reset failed for"
"vpath:%d", vp_id);
- return status;
+ return status;
}
} else
return VXGE_HW_FAIL;
@@ -1950,19 +1950,19 @@ static enum vxge_hw_status vxge_rth_configure(struct vxgedev *vdev)
* for all VPATHs. The h/w only uses the lowest numbered VPATH
* when steering frames.
*/
- for (index = 0; index < vdev->no_of_vpath; index++) {
+ for (index = 0; index < vdev->no_of_vpath; index++) {
status = vxge_hw_vpath_rts_rth_set(
vdev->vpaths[index].handle,
vdev->config.rth_algorithm,
&hash_types,
vdev->config.rth_bkt_sz);
- if (status != VXGE_HW_OK) {
+ if (status != VXGE_HW_OK) {
vxge_debug_init(VXGE_ERR,
"RTH configuration failed for vpath:%d",
vdev->vpaths[index].device_id);
return status;
- }
- }
+ }
+ }
return status;
}
@@ -1991,7 +1991,7 @@ static enum vxge_hw_status vxge_reset_all_vpaths(struct vxgedev *vdev)
vxge_debug_init(VXGE_ERR,
"vxge_hw_vpath_reset failed for "
"vpath:%d", i);
- return status;
+ return status;
}
}
}
@@ -2474,32 +2474,31 @@ static int vxge_add_isr(struct vxgedev *vdev)
switch (msix_idx) {
case 0:
snprintf(vdev->desc[intr_cnt], VXGE_INTR_STRLEN,
- "%s:vxge:MSI-X %d - Tx - fn:%d vpath:%d",
+ "%s:vxge:MSI-X %d - Tx - fn:%d vpath:%d",
vdev->ndev->name,
vdev->entries[intr_cnt].entry,
pci_fun, vp_idx);
ret = request_irq(
- vdev->entries[intr_cnt].vector,
+ vdev->entries[intr_cnt].vector,
vxge_tx_msix_handle, 0,
vdev->desc[intr_cnt],
&vdev->vpaths[vp_idx].fifo);
- vdev->vxge_entries[intr_cnt].arg =
+ vdev->vxge_entries[intr_cnt].arg =
&vdev->vpaths[vp_idx].fifo;
irq_req = 1;
break;
case 1:
snprintf(vdev->desc[intr_cnt], VXGE_INTR_STRLEN,
- "%s:vxge:MSI-X %d - Rx - fn:%d vpath:%d",
+ "%s:vxge:MSI-X %d - Rx - fn:%d vpath:%d",
vdev->ndev->name,
vdev->entries[intr_cnt].entry,
pci_fun, vp_idx);
ret = request_irq(
- vdev->entries[intr_cnt].vector,
- vxge_rx_msix_napi_handle,
- 0,
+ vdev->entries[intr_cnt].vector,
+ vxge_rx_msix_napi_handle, 0,
vdev->desc[intr_cnt],
&vdev->vpaths[vp_idx].ring);
- vdev->vxge_entries[intr_cnt].arg =
+ vdev->vxge_entries[intr_cnt].arg =
&vdev->vpaths[vp_idx].ring;
irq_req = 1;
break;
@@ -2512,9 +2511,9 @@ static int vxge_add_isr(struct vxgedev *vdev)
vxge_rem_msix_isr(vdev);
vdev->config.intr_type = INTA;
vxge_debug_init(VXGE_ERR,
- "%s: Defaulting to INTA"
- , vdev->ndev->name);
- goto INTA_MODE;
+ "%s: Defaulting to INTA",
+ vdev->ndev->name);
+ goto INTA_MODE;
}
if (irq_req) {
@@ -4505,8 +4504,8 @@ vxge_probe(struct pci_dev *pdev, const struct pci_device_id *pre)
if (status != VXGE_HW_OK) {
vxge_debug_init(VXGE_ERR,
"Failed to initialize device (%d)", status);
- ret = -EINVAL;
- goto _exit3;
+ ret = -EINVAL;
+ goto _exit3;
}
if (VXGE_FW_VER(ll_config->device_hw_info.fw_version.major,
