diff --git a/arch/powerpc/platforms/chrp/gg2.h b/arch/powerpc/platforms/chrp/gg2.h
new file mode 100644
index 0000000..341ae55
--- /dev/null
+++ b/arch/powerpc/platforms/chrp/gg2.h
@@ -0,0 +1,61 @@
+/*
+ *  include/asm-ppc/gg2.h -- VLSI VAS96011/12 `Golden Gate 2' register definitions
+ *
+ *  Copyright (C) 1997 Geert Uytterhoeven
+ *
+ *  This file is based on the following documentation:
+ *
+ *	The VAS96011/12 Chipset, Data Book, Edition 1.0
+ *	VLSI Technology, Inc.
+ *
+ *  This file is subject to the terms and conditions of the GNU General Public
+ *  License.  See the file COPYING in the main directory of this archive
+ *  for more details.
+ */
+
+#ifndef _ASMPPC_GG2_H
+#define _ASMPPC_GG2_H
+
+    /*
+     *  Memory Map (CHRP mode)
+     */
+
+#define GG2_PCI_MEM_BASE	0xc0000000	/* Peripheral memory space */
+#define GG2_ISA_MEM_BASE	0xf7000000	/* Peripheral memory alias */
+#define GG2_ISA_IO_BASE		0xf8000000	/* Peripheral I/O space */
+#define GG2_PCI_CONFIG_BASE	0xfec00000	/* PCI configuration space */
+#define GG2_INT_ACK_SPECIAL	0xfec80000	/* Interrupt acknowledge and */
+						/* special PCI cycles */
+#define GG2_ROM_BASE0		0xff000000	/* ROM bank 0 */
+#define GG2_ROM_BASE1		0xff800000	/* ROM bank 1 */
+
+
+    /*
+     *  GG2 specific PCI Registers
+     */
+
+extern void __iomem *gg2_pci_config_base;	/* kernel virtual address */
+
+#define GG2_PCI_BUSNO		0x40	/* Bus number */
+#define GG2_PCI_SUBBUSNO	0x41	/* Subordinate bus number */
+#define GG2_PCI_DISCCTR		0x42	/* Disconnect counter */
+#define GG2_PCI_PPC_CTRL	0x50	/* PowerPC interface control register */
+#define GG2_PCI_ADDR_MAP	0x5c	/* Address map */
+#define GG2_PCI_PCI_CTRL	0x60	/* PCI interface control register */
+#define GG2_PCI_ROM_CTRL	0x70	/* ROM interface control register */
+#define GG2_PCI_ROM_TIME	0x74	/* ROM timing */
+#define GG2_PCI_CC_CTRL		0x80	/* Cache controller control register */
+#define GG2_PCI_DRAM_BANK0	0x90	/* Control register for DRAM bank #0 */
+#define GG2_PCI_DRAM_BANK1	0x94	/* Control register for DRAM bank #1 */
+#define GG2_PCI_DRAM_BANK2	0x98	/* Control register for DRAM bank #2 */
+#define GG2_PCI_DRAM_BANK3	0x9c	/* Control register for DRAM bank #3 */
+#define GG2_PCI_DRAM_BANK4	0xa0	/* Control register for DRAM bank #4 */
+#define GG2_PCI_DRAM_BANK5	0xa4	/* Control register for DRAM bank #5 */
+#define GG2_PCI_DRAM_TIME0	0xb0	/* Timing parameters set #0 */
+#define GG2_PCI_DRAM_TIME1	0xb4	/* Timing parameters set #1 */
+#define GG2_PCI_DRAM_CTRL	0xc0	/* DRAM control */
+#define GG2_PCI_ERR_CTRL	0xd0	/* Error control register */
+#define GG2_PCI_ERR_STATUS	0xd4	/* Error status register */
+					/* Cleared when read */
+
+#endif /* _ASMPPC_GG2_H */
diff --git a/arch/powerpc/platforms/chrp/pci.c b/arch/powerpc/platforms/chrp/pci.c
index 974952e..e43465d 100644
--- a/arch/powerpc/platforms/chrp/pci.c
+++ b/arch/powerpc/platforms/chrp/pci.c
@@ -13,7 +13,6 @@
 #include <asm/irq.h>
 #include <asm/hydra.h>
 #include <asm/prom.h>
-#include <asm/gg2.h>
 #include <asm/machdep.h>
 #include <asm/sections.h>
 #include <asm/pci-bridge.h>
@@ -21,6 +20,7 @@
 #include <asm/rtas.h>
 
 #include "chrp.h"
+#include "gg2.h"
 
 /* LongTrail */
 void __iomem *gg2_pci_config_base;
diff --git a/arch/powerpc/platforms/chrp/setup.c b/arch/powerpc/platforms/chrp/setup.c
index dde5ef4..96498ad 100644
--- a/arch/powerpc/platforms/chrp/setup.c
+++ b/arch/powerpc/platforms/chrp/setup.c
@@ -37,7 +37,6 @@
 #include <asm/io.h>
 #include <asm/pgtable.h>
 #include <asm/prom.h>
-#include <asm/gg2.h>
 #include <asm/pci-bridge.h>
 #include <asm/dma.h>
 #include <asm/machdep.h>
@@ -51,6 +50,7 @@
 #include <asm/xmon.h>
 
 #include "chrp.h"
+#include "gg2.h"
 
 void rtas_indicator_progress(char *, unsigned short);
 
diff --git a/arch/powerpc/platforms/embedded6xx/linkstation.c b/arch/powerpc/platforms/embedded6xx/linkstation.c
index 8c60e02..61ca02c 100644
--- a/arch/powerpc/platforms/embedded6xx/linkstation.c
+++ b/arch/powerpc/platforms/embedded6xx/linkstation.c
@@ -18,9 +18,10 @@
 #include <asm/time.h>
 #include <asm/prom.h>
 #include <asm/mpic.h>
-#include <asm/mpc10x.h>
 #include <asm/pci-bridge.h>
 
+#include "mpc10x.h"
+
 static struct mtd_partition linkstation_physmap_partitions[] = {
 	{
 		.name   = "mtd_firmimg",
diff --git a/arch/powerpc/platforms/embedded6xx/ls_uart.c b/arch/powerpc/platforms/embedded6xx/ls_uart.c
index f7a4def..0d9f150 100644
--- a/arch/powerpc/platforms/embedded6xx/ls_uart.c
+++ b/arch/powerpc/platforms/embedded6xx/ls_uart.c
@@ -4,10 +4,11 @@
 #include <linux/serial_reg.h>
 #include <linux/serial_8250.h>
 #include <asm/io.h>
-#include <asm/mpc10x.h>
 #include <asm/prom.h>
 #include <asm/termbits.h>
 
+#include "mpc10x.h"
+
 static void __iomem *avr_addr;
 static unsigned long avr_clock;
 
diff --git a/arch/powerpc/platforms/embedded6xx/mpc10x.h b/arch/powerpc/platforms/embedded6xx/mpc10x.h
new file mode 100644
index 0000000..b30a6a3
--- /dev/null
+++ b/arch/powerpc/platforms/embedded6xx/mpc10x.h
@@ -0,0 +1,180 @@
+/*
+ * Common routines for the Motorola SPS MPC106/8240/107 Host bridge/Mem
+ * ctlr/EPIC/etc.
+ *
+ * Author: Mark A. Greer
+ *         mgreer@mvista.com
+ *
+ * 2001 (c) MontaVista, Software, Inc.  This file is licensed under
+ * the terms of the GNU General Public License version 2.  This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#ifndef __PPC_KERNEL_MPC10X_H
+#define __PPC_KERNEL_MPC10X_H
+
+#include <linux/pci_ids.h>
+#include <asm/pci-bridge.h>
+
+/*
+ * The values here don't completely map everything but should work in most
+ * cases.
+ *
+ * MAP A (PReP Map)
+ *   Processor: 0x80000000 - 0x807fffff -> PCI I/O: 0x00000000 - 0x007fffff
+ *   Processor: 0xc0000000 - 0xdfffffff -> PCI MEM: 0x00000000 - 0x1fffffff
+ *   PCI MEM:   0x80000000 -> Processor System Memory: 0x00000000
+ *   EUMB mapped to: ioremap_base - 0x00100000 (ioremap_base - 1 MB)
+ *
+ * MAP B (CHRP Map)
+ *   Processor: 0xfe000000 - 0xfebfffff -> PCI I/O: 0x00000000 - 0x00bfffff
+ *   Processor: 0x80000000 - 0xbfffffff -> PCI MEM: 0x80000000 - 0xbfffffff
+ *   PCI MEM:   0x00000000 -> Processor System Memory: 0x00000000
+ *   EUMB mapped to: ioremap_base - 0x00100000 (ioremap_base - 1 MB)
+ */
+
+/*
+ * Define the vendor/device IDs for the various bridges--should be added to
+ * <linux/pci_ids.h>
+ */
+#define	MPC10X_BRIDGE_106	((PCI_DEVICE_ID_MOTOROLA_MPC106 << 16) |  \
+				  PCI_VENDOR_ID_MOTOROLA)
+#define	MPC10X_BRIDGE_8240	((0x0003 << 16) | PCI_VENDOR_ID_MOTOROLA)
+#define	MPC10X_BRIDGE_107	((0x0004 << 16) | PCI_VENDOR_ID_MOTOROLA)
+#define	MPC10X_BRIDGE_8245	((0x0006 << 16) | PCI_VENDOR_ID_MOTOROLA)
+
+/* Define the type of map to use */
+#define	MPC10X_MEM_MAP_A		1
+#define	MPC10X_MEM_MAP_B		2
+
+/* Map A (PReP Map) Defines */
+#define	MPC10X_MAPA_CNFG_ADDR		0x80000cf8
+#define	MPC10X_MAPA_CNFG_DATA		0x80000cfc
+
+#define MPC10X_MAPA_ISA_IO_BASE		0x80000000
+#define MPC10X_MAPA_ISA_MEM_BASE	0xc0000000
+#define	MPC10X_MAPA_DRAM_OFFSET		0x80000000
+
+#define	MPC10X_MAPA_PCI_INTACK_ADDR	0xbffffff0
+#define	MPC10X_MAPA_PCI_IO_START	0x00000000
+#define	MPC10X_MAPA_PCI_IO_END	       (0x00800000 - 1)
+#define	MPC10X_MAPA_PCI_MEM_START	0x00000000
+#define	MPC10X_MAPA_PCI_MEM_END	       (0x20000000 - 1)
+
+#define	MPC10X_MAPA_PCI_MEM_OFFSET	(MPC10X_MAPA_ISA_MEM_BASE -	\
+					 MPC10X_MAPA_PCI_MEM_START)
+
+/* Map B (CHRP Map) Defines */
+#define	MPC10X_MAPB_CNFG_ADDR		0xfec00000
+#define	MPC10X_MAPB_CNFG_DATA		0xfee00000
+
+#define MPC10X_MAPB_ISA_IO_BASE		0xfe000000
+#define MPC10X_MAPB_ISA_MEM_BASE	0x80000000
+#define	MPC10X_MAPB_DRAM_OFFSET		0x00000000
+
+#define	MPC10X_MAPB_PCI_INTACK_ADDR	0xfef00000
+#define	MPC10X_MAPB_PCI_IO_START	0x00000000
+#define	MPC10X_MAPB_PCI_IO_END	       (0x00c00000 - 1)
+#define	MPC10X_MAPB_PCI_MEM_START	0x80000000
+#define	MPC10X_MAPB_PCI_MEM_END	       (0xc0000000 - 1)
+
+#define	MPC10X_MAPB_PCI_MEM_OFFSET	(MPC10X_MAPB_ISA_MEM_BASE -	\
+					 MPC10X_MAPB_PCI_MEM_START)
+
+/* Set hose members to values appropriate for the mem map used */
+#define	MPC10X_SETUP_HOSE(hose, map) {					\
+	(hose)->pci_mem_offset = MPC10X_MAP##map##_PCI_MEM_OFFSET;	\
+	(hose)->io_space.start = MPC10X_MAP##map##_PCI_IO_START;	\
+	(hose)->io_space.end = MPC10X_MAP##map##_PCI_IO_END;		\
+	(hose)->mem_space.start = MPC10X_MAP##map##_PCI_MEM_START;	\
+	(hose)->mem_space.end = MPC10X_MAP##map##_PCI_MEM_END;		\
+	(hose)->io_base_virt = (void *)MPC10X_MAP##map##_ISA_IO_BASE;	\
+}
+
+
+/* Miscellaneous Configuration register offsets */
+#define	MPC10X_CFG_PIR_REG		0x09
+#define	MPC10X_CFG_PIR_HOST_BRIDGE	0x00
+#define	MPC10X_CFG_PIR_AGENT		0x01
+
+#define	MPC10X_CFG_EUMBBAR		0x78
+
+#define	MPC10X_CFG_PICR1_REG		0xa8
+#define	MPC10X_CFG_PICR1_ADDR_MAP_MASK	0x00010000
+#define	MPC10X_CFG_PICR1_ADDR_MAP_A	0x00010000
+#define	MPC10X_CFG_PICR1_ADDR_MAP_B	0x00000000
+#define	MPC10X_CFG_PICR1_SPEC_PCI_RD	0x00000004
+#define	MPC10X_CFG_PICR1_ST_GATH_EN	0x00000040
+
+#define	MPC10X_CFG_PICR2_REG		0xac
+#define	MPC10X_CFG_PICR2_COPYBACK_OPT	0x00000001
+
+#define	MPC10X_CFG_MAPB_OPTIONS_REG	0xe0
+#define	MPC10X_CFG_MAPB_OPTIONS_CFAE	0x80	/* CPU_FD_ALIAS_EN */
+#define	MPC10X_CFG_MAPB_OPTIONS_PFAE	0x40	/* PCI_FD_ALIAS_EN */
+#define	MPC10X_CFG_MAPB_OPTIONS_DR	0x20	/* DLL_RESET */
+#define	MPC10X_CFG_MAPB_OPTIONS_PCICH	0x08	/* PCI_COMPATIBILITY_HOLE */
+#define	MPC10X_CFG_MAPB_OPTIONS_PROCCH	0x04	/* PROC_COMPATIBILITY_HOLE */
+
+/* Define offsets for the memory controller registers in the config space */
+#define MPC10X_MCTLR_MEM_START_1	0x80	/* Banks 0-3 */
+#define MPC10X_MCTLR_MEM_START_2	0x84	/* Banks 4-7 */
+#define MPC10X_MCTLR_EXT_MEM_START_1	0x88	/* Banks 0-3 */
+#define MPC10X_MCTLR_EXT_MEM_START_2	0x8c	/* Banks 4-7 */
+
+#define MPC10X_MCTLR_MEM_END_1		0x90	/* Banks 0-3 */
+#define MPC10X_MCTLR_MEM_END_2		0x94	/* Banks 4-7 */
+#define MPC10X_MCTLR_EXT_MEM_END_1	0x98	/* Banks 0-3 */
+#define MPC10X_MCTLR_EXT_MEM_END_2	0x9c	/* Banks 4-7 */
+
+#define MPC10X_MCTLR_MEM_BANK_ENABLES	0xa0
+
+/* Define some offset in the EUMB */
+#define	MPC10X_EUMB_SIZE		0x00100000 /* Total EUMB size (1MB) */
+
+#define MPC10X_EUMB_MU_OFFSET		0x00000000 /* Msg Unit reg offset */
+#define MPC10X_EUMB_MU_SIZE		0x00001000 /* Msg Unit reg size */
+#define MPC10X_EUMB_DMA_OFFSET		0x00001000 /* DMA Unit reg offset */
+#define MPC10X_EUMB_DMA_SIZE		0x00001000 /* DMA Unit reg size  */
+#define MPC10X_EUMB_ATU_OFFSET		0x00002000 /* Addr xlate reg offset */
+#define MPC10X_EUMB_ATU_SIZE		0x00001000 /* Addr xlate reg size  */
+#define MPC10X_EUMB_I2C_OFFSET		0x00003000 /* I2C Unit reg offset */
+#define MPC10X_EUMB_I2C_SIZE		0x00001000 /* I2C Unit reg size  */
+#define MPC10X_EUMB_DUART_OFFSET	0x00004000 /* DUART Unit reg offset (8245) */
+#define MPC10X_EUMB_DUART_SIZE		0x00001000 /* DUART Unit reg size (8245) */
+#define	MPC10X_EUMB_EPIC_OFFSET		0x00040000 /* EPIC offset in EUMB */
+#define	MPC10X_EUMB_EPIC_SIZE		0x00030000 /* EPIC size */
+#define MPC10X_EUMB_PM_OFFSET		0x000fe000 /* Performance Monitor reg offset (8245) */
+#define MPC10X_EUMB_PM_SIZE		0x00001000 /* Performance Monitor reg size (8245) */
+#define MPC10X_EUMB_WP_OFFSET		0x000ff000 /* Data path diagnostic, watchpoint reg offset */
+#define MPC10X_EUMB_WP_SIZE		0x00001000 /* Data path diagnostic, watchpoint reg size */
+
+/*
+ * Define some recommended places to put the EUMB regs.
+ * For both maps, recommend putting the EUMB from 0xeff00000 to 0xefffffff.
+ */
+extern unsigned long			ioremap_base;
+#define	MPC10X_MAPA_EUMB_BASE		(ioremap_base - MPC10X_EUMB_SIZE)
+#define	MPC10X_MAPB_EUMB_BASE		MPC10X_MAPA_EUMB_BASE
+
+enum ppc_sys_devices {
+	MPC10X_IIC1,
+	MPC10X_DMA0,
+	MPC10X_DMA1,
+	MPC10X_UART0,
+	MPC10X_UART1,
+	NUM_PPC_SYS_DEVS,
+};
+
+int mpc10x_bridge_init(struct pci_controller *hose,
+		       uint current_map,
+		       uint new_map,
+		       uint phys_eumb_base);
+unsigned long mpc10x_get_mem_size(uint mem_map);
+int mpc10x_enable_store_gathering(struct pci_controller *hose);
+int mpc10x_disable_store_gathering(struct pci_controller *hose);
+
+/* For MPC107 boards that use the built-in openpic */
+void mpc10x_set_openpic(void);
+
+#endif	/* __PPC_KERNEL_MPC10X_H */
diff --git a/drivers/macintosh/ans-lcd.c b/drivers/macintosh/ans-lcd.c
index e54c4d9..73c50bc 100644
--- a/drivers/macintosh/ans-lcd.c
+++ b/drivers/macintosh/ans-lcd.c
@@ -14,9 +14,10 @@
 #include <asm/uaccess.h>
 #include <asm/sections.h>
 #include <asm/prom.h>
-#include <asm/ans-lcd.h>
 #include <asm/io.h>
 
+#include "ans-lcd.h"
+
 #define ANSLCD_ADDR		0xf301c000
 #define ANSLCD_CTRL_IX 0x00
 #define ANSLCD_DATA_IX 0x10
diff --git a/include/asm-ppc/ans-lcd.h b/drivers/macintosh/ans-lcd.h
similarity index 100%
rename from include/asm-ppc/ans-lcd.h
rename to drivers/macintosh/ans-lcd.h
diff --git a/include/asm-powerpc/8xx_immap.h b/include/asm-powerpc/8xx_immap.h
new file mode 100644
index 0000000..1311cef
--- /dev/null
+++ b/include/asm-powerpc/8xx_immap.h
@@ -0,0 +1,564 @@
+/*
+ * MPC8xx Internal Memory Map
+ * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+ *
+ * The I/O on the MPC860 is comprised of blocks of special registers
+ * and the dual port ram for the Communication Processor Module.
+ * Within this space are functional units such as the SIU, memory
+ * controller, system timers, and other control functions.  It is
+ * a combination that I found difficult to separate into logical
+ * functional files.....but anyone else is welcome to try.  -- Dan
+ */
+#ifdef __KERNEL__
+#ifndef __IMMAP_8XX__
+#define __IMMAP_8XX__
+
+/* System configuration registers.
+*/
+typedef	struct sys_conf {
+	uint	sc_siumcr;
+	uint	sc_sypcr;
+	uint	sc_swt;
+	char	res1[2];
+	ushort	sc_swsr;
+	uint	sc_sipend;
+	uint	sc_simask;
+	uint	sc_siel;
+	uint	sc_sivec;
+	uint	sc_tesr;
+	char	res2[0xc];
+	uint	sc_sdcr;
+	char	res3[0x4c];
+} sysconf8xx_t;
+
+/* PCMCIA configuration registers.
+*/
+typedef struct pcmcia_conf {
+	uint	pcmc_pbr0;
+	uint	pcmc_por0;
+	uint	pcmc_pbr1;
+	uint	pcmc_por1;
+	uint	pcmc_pbr2;
+	uint	pcmc_por2;
+	uint	pcmc_pbr3;
+	uint	pcmc_por3;
+	uint	pcmc_pbr4;
+	uint	pcmc_por4;
+	uint	pcmc_pbr5;
+	uint	pcmc_por5;
+	uint	pcmc_pbr6;
+	uint	pcmc_por6;
+	uint	pcmc_pbr7;
+	uint	pcmc_por7;
+	char	res1[0x20];
+	uint	pcmc_pgcra;
+	uint	pcmc_pgcrb;
+	uint	pcmc_pscr;
+	char	res2[4];
+	uint	pcmc_pipr;
+	char	res3[4];
+	uint	pcmc_per;
+	char	res4[4];
+} pcmconf8xx_t;
+
+/* Memory controller registers.
+*/
+typedef struct	mem_ctlr {
+	uint	memc_br0;
+	uint	memc_or0;
+	uint	memc_br1;
+	uint	memc_or1;
+	uint	memc_br2;
+	uint	memc_or2;
+	uint	memc_br3;
+	uint	memc_or3;
+	uint	memc_br4;
+	uint	memc_or4;
+	uint	memc_br5;
+	uint	memc_or5;
+	uint	memc_br6;
+	uint	memc_or6;
+	uint	memc_br7;
+	uint	memc_or7;
+	char	res1[0x24];
+	uint	memc_mar;
+	uint	memc_mcr;
+	char	res2[4];
+	uint	memc_mamr;
+	uint	memc_mbmr;
+	ushort	memc_mstat;
+	ushort	memc_mptpr;
+	uint	memc_mdr;
+	char	res3[0x80];
+} memctl8xx_t;
+
+/*-----------------------------------------------------------------------
+ * BR - Memory Controler: Base Register					16-9
+ */
+#define BR_BA_MSK	0xffff8000	/* Base Address Mask			*/
+#define BR_AT_MSK	0x00007000	/* Address Type Mask			*/
+#define BR_PS_MSK	0x00000c00	/* Port Size Mask			*/
+#define BR_PS_32	0x00000000	/* 32 bit port size			*/
+#define BR_PS_16	0x00000800	/* 16 bit port size			*/
+#define BR_PS_8		0x00000400	/*  8 bit port size			*/
+#define BR_PARE		0x00000200	/* Parity Enable			*/
+#define BR_WP		0x00000100	/* Write Protect			*/
+#define BR_MS_MSK	0x000000c0	/* Machine Select Mask			*/
+#define BR_MS_GPCM	0x00000000	/* G.P.C.M. Machine Select		*/
+#define BR_MS_UPMA	0x00000080	/* U.P.M.A Machine Select		*/
+#define BR_MS_UPMB	0x000000c0	/* U.P.M.B Machine Select		*/
+#define BR_V		0x00000001	/* Bank Valid				*/
+
+/*-----------------------------------------------------------------------
+ * OR - Memory Controler: Option Register				16-11
+ */
+#define OR_AM_MSK	0xffff8000	/* Address Mask Mask			*/
+#define OR_ATM_MSK	0x00007000	/* Address Type Mask Mask		*/
+#define OR_CSNT_SAM	0x00000800	/* Chip Select Negation Time/ Start	*/
+					/* Address Multiplex			*/
+#define OR_ACS_MSK	0x00000600	/* Address to Chip Select Setup mask	*/
+#define OR_ACS_DIV1	0x00000000	/* CS is output at the same time	*/
+#define OR_ACS_DIV4	0x00000400	/* CS is output 1/4 a clock later	*/
+#define OR_ACS_DIV2	0x00000600	/* CS is output 1/2 a clock later	*/
+#define OR_G5LA		0x00000400	/* Output #GPL5 on #GPL_A5		*/
+#define OR_G5LS		0x00000200	/* Drive #GPL high on falling edge of...*/
+#define OR_BI		0x00000100	/* Burst inhibit			*/
+#define OR_SCY_MSK	0x000000f0	/* Cycle Lenght in Clocks		*/
+#define OR_SCY_0_CLK	0x00000000	/* 0 clock cycles wait states		*/
+#define OR_SCY_1_CLK	0x00000010	/* 1 clock cycles wait states		*/
+#define OR_SCY_2_CLK	0x00000020	/* 2 clock cycles wait states		*/
+#define OR_SCY_3_CLK	0x00000030	/* 3 clock cycles wait states		*/
+#define OR_SCY_4_CLK	0x00000040	/* 4 clock cycles wait states		*/
+#define OR_SCY_5_CLK	0x00000050	/* 5 clock cycles wait states		*/
+#define OR_SCY_6_CLK	0x00000060	/* 6 clock cycles wait states		*/
+#define OR_SCY_7_CLK	0x00000070	/* 7 clock cycles wait states		*/
+#define OR_SCY_8_CLK	0x00000080	/* 8 clock cycles wait states		*/
+#define OR_SCY_9_CLK	0x00000090	/* 9 clock cycles wait states		*/
+#define OR_SCY_10_CLK	0x000000a0	/* 10 clock cycles wait states		*/
+#define OR_SCY_11_CLK	0x000000b0	/* 11 clock cycles wait states		*/
+#define OR_SCY_12_CLK	0x000000c0	/* 12 clock cycles wait states		*/
+#define OR_SCY_13_CLK	0x000000d0	/* 13 clock cycles wait states		*/
+#define OR_SCY_14_CLK	0x000000e0	/* 14 clock cycles wait states		*/
+#define OR_SCY_15_CLK	0x000000f0	/* 15 clock cycles wait states		*/
+#define OR_SETA		0x00000008	/* External Transfer Acknowledge	*/
+#define OR_TRLX		0x00000004	/* Timing Relaxed			*/
+#define OR_EHTR		0x00000002	/* Extended Hold Time on Read		*/
+
+/* System Integration Timers.
+*/
+typedef struct	sys_int_timers {
+	ushort	sit_tbscr;
+	char	res0[0x02];
+	uint	sit_tbreff0;
+	uint	sit_tbreff1;
+	char	res1[0x14];
+	ushort	sit_rtcsc;
+	char	res2[0x02];
+	uint	sit_rtc;
+	uint	sit_rtsec;
+	uint	sit_rtcal;
+	char	res3[0x10];
+	ushort	sit_piscr;
+	char	res4[2];
+	uint	sit_pitc;
+	uint	sit_pitr;
+	char	res5[0x34];
+} sit8xx_t;
+
+#define TBSCR_TBIRQ_MASK	((ushort)0xff00)
+#define TBSCR_REFA		((ushort)0x0080)
+#define TBSCR_REFB		((ushort)0x0040)
+#define TBSCR_REFAE		((ushort)0x0008)
+#define TBSCR_REFBE		((ushort)0x0004)
+#define TBSCR_TBF		((ushort)0x0002)
+#define TBSCR_TBE		((ushort)0x0001)
+
+#define RTCSC_RTCIRQ_MASK	((ushort)0xff00)
+#define RTCSC_SEC		((ushort)0x0080)
+#define RTCSC_ALR		((ushort)0x0040)
+#define RTCSC_38K		((ushort)0x0010)
+#define RTCSC_SIE		((ushort)0x0008)
+#define RTCSC_ALE		((ushort)0x0004)
+#define RTCSC_RTF		((ushort)0x0002)
+#define RTCSC_RTE		((ushort)0x0001)
+
+#define PISCR_PIRQ_MASK		((ushort)0xff00)
+#define PISCR_PS		((ushort)0x0080)
+#define PISCR_PIE		((ushort)0x0004)
+#define PISCR_PTF		((ushort)0x0002)
+#define PISCR_PTE		((ushort)0x0001)
+
+/* Clocks and Reset.
+*/
+typedef struct clk_and_reset {
+	uint	car_sccr;
+	uint	car_plprcr;
+	uint	car_rsr;
+	char	res[0x74];        /* Reserved area                  */
+} car8xx_t;
+
+/* System Integration Timers keys.
+*/
+typedef struct sitk {
+	uint	sitk_tbscrk;
+	uint	sitk_tbreff0k;
+	uint	sitk_tbreff1k;
+	uint	sitk_tbk;
+	char	res1[0x10];
+	uint	sitk_rtcsck;
+	uint	sitk_rtck;
+	uint	sitk_rtseck;
+	uint	sitk_rtcalk;
+	char	res2[0x10];
+	uint	sitk_piscrk;
+	uint	sitk_pitck;
+	char	res3[0x38];
+} sitk8xx_t;
+
+/* Clocks and reset keys.
+*/
+typedef struct cark {
+	uint	cark_sccrk;
+	uint	cark_plprcrk;
+	uint	cark_rsrk;
+	char	res[0x474];
+} cark8xx_t;
+
+/* The key to unlock registers maintained by keep-alive power.
+*/
+#define KAPWR_KEY	((unsigned int)0x55ccaa33)
+
+/* Video interface.  MPC823 Only.
+*/
+typedef struct vid823 {
+	ushort	vid_vccr;
+	ushort	res1;
+	u_char	vid_vsr;
+	u_char	res2;
+	u_char	vid_vcmr;
+	u_char	res3;
+	uint	vid_vbcb;
+	uint	res4;
+	uint	vid_vfcr0;
+	uint	vid_vfaa0;
+	uint	vid_vfba0;
+	uint	vid_vfcr1;
+	uint	vid_vfaa1;
+	uint	vid_vfba1;
+	u_char	res5[0x18];
+} vid823_t;
+
+/* LCD interface.  823 Only.
+*/
+typedef struct lcd {
+	uint	lcd_lccr;
+	uint	lcd_lchcr;
+	uint	lcd_lcvcr;
+	char	res1[4];
+	uint	lcd_lcfaa;
+	uint	lcd_lcfba;
+	char	lcd_lcsr;
+	char	res2[0x7];
+} lcd823_t;
+
+/* I2C
+*/
+typedef struct i2c {
+	u_char	i2c_i2mod;
+	char	res1[3];
+	u_char	i2c_i2add;
+	char	res2[3];
+	u_char	i2c_i2brg;
+	char	res3[3];
+	u_char	i2c_i2com;
+	char	res4[3];
+	u_char	i2c_i2cer;
+	char	res5[3];
+	u_char	i2c_i2cmr;
+	char	res6[0x8b];
+} i2c8xx_t;
+
+/* DMA control/status registers.
+*/
+typedef struct sdma_csr {
+	char	res1[4];
+	uint	sdma_sdar;
+	u_char	sdma_sdsr;
+	char	res3[3];
+	u_char	sdma_sdmr;
+	char	res4[3];
+	u_char	sdma_idsr1;
+	char	res5[3];
+	u_char	sdma_idmr1;
+	char	res6[3];
+	u_char	sdma_idsr2;
+	char	res7[3];
+	u_char	sdma_idmr2;
+	char	res8[0x13];
+} sdma8xx_t;
+
+/* Communication Processor Module Interrupt Controller.
+*/
+typedef struct cpm_ic {
+	ushort	cpic_civr;
+	char	res[0xe];
+	uint	cpic_cicr;
+	uint	cpic_cipr;
+	uint	cpic_cimr;
+	uint	cpic_cisr;
+} cpic8xx_t;
+
+/* Input/Output Port control/status registers.
+*/
+typedef struct io_port {
+	ushort	iop_padir;
+	ushort	iop_papar;
+	ushort	iop_paodr;
+	ushort	iop_padat;
+	char	res1[8];
+	ushort	iop_pcdir;
+	ushort	iop_pcpar;
+	ushort	iop_pcso;
+	ushort	iop_pcdat;
+	ushort	iop_pcint;
+	char	res2[6];
+	ushort	iop_pddir;
+	ushort	iop_pdpar;
+	char	res3[2];
+	ushort	iop_pddat;
+	uint	utmode;
+	char	res4[4];
+} iop8xx_t;
+
+/* Communication Processor Module Timers
+*/
+typedef struct cpm_timers {
+	ushort	cpmt_tgcr;
+	char	res1[0xe];
+	ushort	cpmt_tmr1;
+	ushort	cpmt_tmr2;
+	ushort	cpmt_trr1;
+	ushort	cpmt_trr2;
+	ushort	cpmt_tcr1;
+	ushort	cpmt_tcr2;
+	ushort	cpmt_tcn1;
+	ushort	cpmt_tcn2;
+	ushort	cpmt_tmr3;
+	ushort	cpmt_tmr4;
+	ushort	cpmt_trr3;
+	ushort	cpmt_trr4;
+	ushort	cpmt_tcr3;
+	ushort	cpmt_tcr4;
+	ushort	cpmt_tcn3;
+	ushort	cpmt_tcn4;
+	ushort	cpmt_ter1;
+	ushort	cpmt_ter2;
+	ushort	cpmt_ter3;
+	ushort	cpmt_ter4;
+	char	res2[8];
+} cpmtimer8xx_t;
+
+/* Finally, the Communication Processor stuff.....
+*/
+typedef struct scc {		/* Serial communication channels */
+	uint	scc_gsmrl;
+	uint	scc_gsmrh;
+	ushort	scc_psmr;
+	char	res1[2];
+	ushort	scc_todr;
+	ushort	scc_dsr;
+	ushort	scc_scce;
+	char	res2[2];
+	ushort	scc_sccm;
+	char	res3;
+	u_char	scc_sccs;
+	char	res4[8];
+} scc_t;
+
+typedef struct smc {		/* Serial management channels */
+	char	res1[2];
+	ushort	smc_smcmr;
+	char	res2[2];
+	u_char	smc_smce;
+	char	res3[3];
+	u_char	smc_smcm;
+	char	res4[5];
+} smc_t;
+
+/* MPC860T Fast Ethernet Controller.  It isn't part of the CPM, but
+ * it fits within the address space.
+ */
+
+typedef struct fec {
+	uint	fec_addr_low;		/* lower 32 bits of station address	*/
+	ushort	fec_addr_high;		/* upper 16 bits of station address	*/
+	ushort	res1;			/* reserved				*/
+	uint	fec_hash_table_high;	/* upper 32-bits of hash table		*/
+	uint	fec_hash_table_low;	/* lower 32-bits of hash table		*/
+	uint	fec_r_des_start;	/* beginning of Rx descriptor ring	*/
+	uint	fec_x_des_start;	/* beginning of Tx descriptor ring	*/
+	uint	fec_r_buff_size;	/* Rx buffer size			*/
+	uint	res2[9];		/* reserved				*/
+	uint	fec_ecntrl;		/* ethernet control register		*/
+	uint	fec_ievent;		/* interrupt event register		*/
+	uint	fec_imask;		/* interrupt mask register		*/
+	uint	fec_ivec;		/* interrupt level and vector status	*/
+	uint	fec_r_des_active;	/* Rx ring updated flag			*/
+	uint	fec_x_des_active;	/* Tx ring updated flag			*/
+	uint	res3[10];		/* reserved				*/
+	uint	fec_mii_data;		/* MII data register			*/
+	uint	fec_mii_speed;		/* MII speed control register		*/
+	uint	res4[17];		/* reserved				*/
+	uint	fec_r_bound;		/* end of RAM (read-only)		*/
+	uint	fec_r_fstart;		/* Rx FIFO start address		*/
+	uint	res5[6];		/* reserved				*/
+	uint	fec_x_fstart;		/* Tx FIFO start address		*/
+	uint	res6[17];		/* reserved				*/
+	uint	fec_fun_code;		/* fec SDMA function code		*/
+	uint	res7[3];		/* reserved				*/
+	uint	fec_r_cntrl;		/* Rx control register			*/
+	uint	fec_r_hash;		/* Rx hash register			*/
+	uint	res8[14];		/* reserved				*/
+	uint	fec_x_cntrl;		/* Tx control register			*/
+	uint	res9[0x1e];		/* reserved				*/
+} fec_t;
+
+/* The FEC and LCD color map share the same address space....
+ * I guess we will never see an 823T :-).
+ */
+union fec_lcd {
+	fec_t	fl_un_fec;
+	u_char	fl_un_cmap[0x200];
+};
+
+typedef struct comm_proc {
+	/* General control and status registers.
+	*/
+	ushort	cp_cpcr;
+	u_char	res1[2];
+	ushort	cp_rccr;
+	u_char	res2;
+	u_char	cp_rmds;
+	u_char	res3[4];
+	ushort	cp_cpmcr1;
+	ushort	cp_cpmcr2;
+	ushort	cp_cpmcr3;
+	ushort	cp_cpmcr4;
+	u_char	res4[2];
+	ushort	cp_rter;
+	u_char	res5[2];
+	ushort	cp_rtmr;
+	u_char	res6[0x14];
+
+	/* Baud rate generators.
+	*/
+	uint	cp_brgc1;
+	uint	cp_brgc2;
+	uint	cp_brgc3;
+	uint	cp_brgc4;
+
+	/* Serial Communication Channels.
+	*/
+	scc_t	cp_scc[4];
+
+	/* Serial Management Channels.
+	*/
+	smc_t	cp_smc[2];
+
+	/* Serial Peripheral Interface.
+	*/
+	ushort	cp_spmode;
+	u_char	res7[4];
+	u_char	cp_spie;
+	u_char	res8[3];
+	u_char	cp_spim;
+	u_char	res9[2];
+	u_char	cp_spcom;
+	u_char	res10[2];
+
+	/* Parallel Interface Port.
+	*/
+	u_char	res11[2];
+	ushort	cp_pipc;
+	u_char	res12[2];
+	ushort	cp_ptpr;
+	uint	cp_pbdir;
+	uint	cp_pbpar;
+	u_char	res13[2];
+	ushort	cp_pbodr;
+	uint	cp_pbdat;
+
+	/* Port E - MPC87x/88x only.
+	 */
+	uint	cp_pedir;
+	uint	cp_pepar;
+	uint	cp_peso;
+	uint	cp_peodr;
+	uint	cp_pedat;
+
+	/* Communications Processor Timing Register -
+	   Contains RMII Timing for the FECs on MPC87x/88x only.
+	*/
+	uint	cp_cptr;
+
+	/* Serial Interface and Time Slot Assignment.
+	*/
+	uint	cp_simode;
+	u_char	cp_sigmr;
+	u_char	res15;
+	u_char	cp_sistr;
+	u_char	cp_sicmr;
+	u_char	res16[4];
+	uint	cp_sicr;
+	uint	cp_sirp;
+	u_char	res17[0xc];
+
+	/* 256 bytes of MPC823 video controller RAM array.
+	*/
+	u_char	cp_vcram[0x100];
+	u_char	cp_siram[0x200];
+
+	/* The fast ethernet controller is not really part of the CPM,
+	 * but it resides in the address space.
+	 * The LCD color map is also here.
+	 */
+	union	fec_lcd	fl_un;
+#define cp_fec		fl_un.fl_un_fec
+#define lcd_cmap	fl_un.fl_un_cmap
+	char	res18[0xE00];
+
+	/* The DUET family has a second FEC here */
+	fec_t	cp_fec2;
+#define cp_fec1	cp_fec	/* consistency macro */
+
+	/* Dual Ported RAM follows.
+	 * There are many different formats for this memory area
+	 * depending upon the devices used and options chosen.
+	 * Some processors don't have all of it populated.
+	 */
+	u_char	cp_dpmem[0x1C00];	/* BD / Data / ucode */
+	u_char	cp_dparam[0x400];	/* Parameter RAM */
+} cpm8xx_t;
+
+/* Internal memory map.
+*/
+typedef struct immap {
+	sysconf8xx_t	im_siu_conf;	/* SIU Configuration */
+	pcmconf8xx_t	im_pcmcia;	/* PCMCIA Configuration */
+	memctl8xx_t	im_memctl;	/* Memory Controller */
+	sit8xx_t	im_sit;		/* System integration timers */
+	car8xx_t	im_clkrst;	/* Clocks and reset */
+	sitk8xx_t	im_sitk;	/* Sys int timer keys */
+	cark8xx_t	im_clkrstk;	/* Clocks and reset keys */
+	vid823_t	im_vid;		/* Video (823 only) */
+	lcd823_t	im_lcd;		/* LCD (823 only) */
+	i2c8xx_t	im_i2c;		/* I2C control/status */
+	sdma8xx_t	im_sdma;	/* SDMA control/status */
+	cpic8xx_t	im_cpic;	/* CPM Interrupt Controller */
+	iop8xx_t	im_ioport;	/* IO Port control/status */
+	cpmtimer8xx_t	im_cpmtimer;	/* CPM timers */
+	cpm8xx_t	im_cpm;		/* Communication processor */
+} immap_t;
+
+#endif /* __IMMAP_8XX__ */
+#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/commproc.h b/include/asm-powerpc/commproc.h
new file mode 100644
index 0000000..3972487
--- /dev/null
+++ b/include/asm-powerpc/commproc.h
@@ -0,0 +1,692 @@
+/*
+ * MPC8xx Communication Processor Module.
+ * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+ *
+ * This file contains structures and information for the communication
+ * processor channels.  Some CPM control and status is available
+ * throught the MPC8xx internal memory map.  See immap.h for details.
+ * This file only contains what I need for the moment, not the total
+ * CPM capabilities.  I (or someone else) will add definitions as they
+ * are needed.  -- Dan
+ *
+ * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
+ * bytes of the DP RAM and relocates the I2C parameter area to the
+ * IDMA1 space.  The remaining DP RAM is available for buffer descriptors
+ * or other use.
+ */
+#ifndef __CPM_8XX__
+#define __CPM_8XX__
+
+#include <asm/8xx_immap.h>
+#include <asm/ptrace.h>
+
+/* CPM Command register.
+*/
+#define CPM_CR_RST	((ushort)0x8000)
+#define CPM_CR_OPCODE	((ushort)0x0f00)
+#define CPM_CR_CHAN	((ushort)0x00f0)
+#define CPM_CR_FLG	((ushort)0x0001)
+
+/* Some commands (there are more...later)
+*/
+#define CPM_CR_INIT_TRX		((ushort)0x0000)
+#define CPM_CR_INIT_RX		((ushort)0x0001)
+#define CPM_CR_INIT_TX		((ushort)0x0002)
+#define CPM_CR_HUNT_MODE	((ushort)0x0003)
+#define CPM_CR_STOP_TX		((ushort)0x0004)
+#define CPM_CR_GRA_STOP_TX	((ushort)0x0005)
+#define CPM_CR_RESTART_TX	((ushort)0x0006)
+#define CPM_CR_CLOSE_RX_BD	((ushort)0x0007)
+#define CPM_CR_SET_GADDR	((ushort)0x0008)
+#define CPM_CR_SET_TIMER	CPM_CR_SET_GADDR
+
+/* Channel numbers.
+*/
+#define CPM_CR_CH_SCC1		((ushort)0x0000)
+#define CPM_CR_CH_I2C		((ushort)0x0001)	/* I2C and IDMA1 */
+#define CPM_CR_CH_SCC2		((ushort)0x0004)
+#define CPM_CR_CH_SPI		((ushort)0x0005)	/* SPI / IDMA2 / Timers */
+#define CPM_CR_CH_TIMER		CPM_CR_CH_SPI
+#define CPM_CR_CH_SCC3		((ushort)0x0008)
+#define CPM_CR_CH_SMC1		((ushort)0x0009)	/* SMC1 / DSP1 */
+#define CPM_CR_CH_SCC4		((ushort)0x000c)
+#define CPM_CR_CH_SMC2		((ushort)0x000d)	/* SMC2 / DSP2 */
+
+#define mk_cr_cmd(CH, CMD)	((CMD << 8) | (CH << 4))
+
+/* The dual ported RAM is multi-functional.  Some areas can be (and are
+ * being) used for microcode.  There is an area that can only be used
+ * as data ram for buffer descriptors, which is all we use right now.
+ * Currently the first 512 and last 256 bytes are used for microcode.
+ */
+#define CPM_DATAONLY_BASE	((uint)0x0800)
+#define CPM_DATAONLY_SIZE	((uint)0x0700)
+#define CPM_DP_NOSPACE		((uint)0x7fffffff)
+
+/* Export the base address of the communication processor registers
+ * and dual port ram.
+ */
+extern	cpm8xx_t	*cpmp;		/* Pointer to comm processor */
+extern unsigned long cpm_dpalloc(uint size, uint align);
+extern int cpm_dpfree(unsigned long offset);
+extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
+extern void cpm_dpdump(void);
+extern void *cpm_dpram_addr(unsigned long offset);
+extern uint cpm_dpram_phys(u8* addr);
+extern void cpm_setbrg(uint brg, uint rate);
+
+extern uint m8xx_cpm_hostalloc(uint size);
+extern int  m8xx_cpm_hostfree(uint start);
+extern void m8xx_cpm_hostdump(void);
+
+extern void cpm_load_patch(volatile immap_t *immr);
+
+/* Buffer descriptors used by many of the CPM protocols.
+*/
+typedef struct cpm_buf_desc {
+	ushort	cbd_sc;		/* Status and Control */
+	ushort	cbd_datlen;	/* Data length in buffer */
+	uint	cbd_bufaddr;	/* Buffer address in host memory */
+} cbd_t;
+
+#define BD_SC_EMPTY	((ushort)0x8000)	/* Receive is empty */
+#define BD_SC_READY	((ushort)0x8000)	/* Transmit is ready */
+#define BD_SC_WRAP	((ushort)0x2000)	/* Last buffer descriptor */
+#define BD_SC_INTRPT	((ushort)0x1000)	/* Interrupt on change */
+#define BD_SC_LAST	((ushort)0x0800)	/* Last buffer in frame */
+#define BD_SC_TC	((ushort)0x0400)	/* Transmit CRC */
+#define BD_SC_CM	((ushort)0x0200)	/* Continous mode */
+#define BD_SC_ID	((ushort)0x0100)	/* Rec'd too many idles */
+#define BD_SC_P		((ushort)0x0100)	/* xmt preamble */
+#define BD_SC_BR	((ushort)0x0020)	/* Break received */
+#define BD_SC_FR	((ushort)0x0010)	/* Framing error */
+#define BD_SC_PR	((ushort)0x0008)	/* Parity error */
+#define BD_SC_NAK	((ushort)0x0004)	/* NAK - did not respond */
+#define BD_SC_OV	((ushort)0x0002)	/* Overrun */
+#define BD_SC_UN	((ushort)0x0002)	/* Underrun */
+#define BD_SC_CD	((ushort)0x0001)	/* ?? */
+#define BD_SC_CL	((ushort)0x0001)	/* Collision */
+
+/* Parameter RAM offsets.
+*/
+#define PROFF_SCC1	((uint)0x0000)
+#define PROFF_IIC	((uint)0x0080)
+#define PROFF_SCC2	((uint)0x0100)
+#define PROFF_SPI	((uint)0x0180)
+#define PROFF_SCC3	((uint)0x0200)
+#define PROFF_SMC1	((uint)0x0280)
+#define PROFF_SCC4	((uint)0x0300)
+#define PROFF_SMC2	((uint)0x0380)
+
+/* Define enough so I can at least use the serial port as a UART.
+ * The MBX uses SMC1 as the host serial port.
+ */
+typedef struct smc_uart {
+	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	smc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	smc_rfcr;	/* Rx function code */
+	u_char	smc_tfcr;	/* Tx function code */
+	ushort	smc_mrblr;	/* Max receive buffer length */
+	uint	smc_rstate;	/* Internal */
+	uint	smc_idp;	/* Internal */
+	ushort	smc_rbptr;	/* Internal */
+	ushort	smc_ibc;	/* Internal */
+	uint	smc_rxtmp;	/* Internal */
+	uint	smc_tstate;	/* Internal */
+	uint	smc_tdp;	/* Internal */
+	ushort	smc_tbptr;	/* Internal */
+	ushort	smc_tbc;	/* Internal */
+	uint	smc_txtmp;	/* Internal */
+	ushort	smc_maxidl;	/* Maximum idle characters */
+	ushort	smc_tmpidl;	/* Temporary idle counter */
+	ushort	smc_brklen;	/* Last received break length */
+	ushort	smc_brkec;	/* rcv'd break condition counter */
+	ushort	smc_brkcr;	/* xmt break count register */
+	ushort	smc_rmask;	/* Temporary bit mask */
+	char	res1[8];	/* Reserved */
+	ushort	smc_rpbase;	/* Relocation pointer */
+} smc_uart_t;
+
+/* Function code bits.
+*/
+#define SMC_EB	((u_char)0x10)	/* Set big endian byte order */
+
+/* SMC uart mode register.
+*/
+#define	SMCMR_REN	((ushort)0x0001)
+#define SMCMR_TEN	((ushort)0x0002)
+#define SMCMR_DM	((ushort)0x000c)
+#define SMCMR_SM_GCI	((ushort)0x0000)
+#define SMCMR_SM_UART	((ushort)0x0020)
+#define SMCMR_SM_TRANS	((ushort)0x0030)
+#define SMCMR_SM_MASK	((ushort)0x0030)
+#define SMCMR_PM_EVEN	((ushort)0x0100)	/* Even parity, else odd */
+#define SMCMR_REVD	SMCMR_PM_EVEN
+#define SMCMR_PEN	((ushort)0x0200)	/* Parity enable */
+#define SMCMR_BS	SMCMR_PEN
+#define SMCMR_SL	((ushort)0x0400)	/* Two stops, else one */
+#define SMCR_CLEN_MASK	((ushort)0x7800)	/* Character length */
+#define smcr_mk_clen(C)	(((C) << 11) & SMCR_CLEN_MASK)
+
+/* SMC2 as Centronics parallel printer.  It is half duplex, in that
+ * it can only receive or transmit.  The parameter ram values for
+ * each direction are either unique or properly overlap, so we can
+ * include them in one structure.
+ */
+typedef struct smc_centronics {
+	ushort	scent_rbase;
+	ushort	scent_tbase;
+	u_char	scent_cfcr;
+	u_char	scent_smask;
+	ushort	scent_mrblr;
+	uint	scent_rstate;
+	uint	scent_r_ptr;
+	ushort	scent_rbptr;
+	ushort	scent_r_cnt;
+	uint	scent_rtemp;
+	uint	scent_tstate;
+	uint	scent_t_ptr;
+	ushort	scent_tbptr;
+	ushort	scent_t_cnt;
+	uint	scent_ttemp;
+	ushort	scent_max_sl;
+	ushort	scent_sl_cnt;
+	ushort	scent_character1;
+	ushort	scent_character2;
+	ushort	scent_character3;
+	ushort	scent_character4;
+	ushort	scent_character5;
+	ushort	scent_character6;
+	ushort	scent_character7;
+	ushort	scent_character8;
+	ushort	scent_rccm;
+	ushort	scent_rccr;
+} smc_cent_t;
+
+/* Centronics Status Mask Register.
+*/
+#define SMC_CENT_F	((u_char)0x08)
+#define SMC_CENT_PE	((u_char)0x04)
+#define SMC_CENT_S	((u_char)0x02)
+
+/* SMC Event and Mask register.
+*/
+#define	SMCM_BRKE	((unsigned char)0x40)	/* When in UART Mode */
+#define	SMCM_BRK	((unsigned char)0x10)	/* When in UART Mode */
+#define	SMCM_TXE	((unsigned char)0x10)	/* When in Transparent Mode */
+#define	SMCM_BSY	((unsigned char)0x04)
+#define	SMCM_TX		((unsigned char)0x02)
+#define	SMCM_RX		((unsigned char)0x01)
+
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST		((uint)0x00020000)
+#define CPM_BRG_EN		((uint)0x00010000)
+#define CPM_BRG_EXTC_INT	((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK2	((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK6	((uint)0x00008000)
+#define CPM_BRG_ATB		((uint)0x00002000)
+#define CPM_BRG_CD_MASK		((uint)0x00001ffe)
+#define CPM_BRG_DIV16		((uint)0x00000001)
+
+/* SI Clock Route Register
+*/
+#define SICR_RCLK_SCC1_BRG1	((uint)0x00000000)
+#define SICR_TCLK_SCC1_BRG1	((uint)0x00000000)
+#define SICR_RCLK_SCC2_BRG2	((uint)0x00000800)
+#define SICR_TCLK_SCC2_BRG2	((uint)0x00000100)
+#define SICR_RCLK_SCC3_BRG3	((uint)0x00100000)
+#define SICR_TCLK_SCC3_BRG3	((uint)0x00020000)
+#define SICR_RCLK_SCC4_BRG4	((uint)0x18000000)
+#define SICR_TCLK_SCC4_BRG4	((uint)0x03000000)
+
+/* SCCs.
+*/
+#define SCC_GSMRH_IRP		((uint)0x00040000)
+#define SCC_GSMRH_GDE		((uint)0x00010000)
+#define SCC_GSMRH_TCRC_CCITT	((uint)0x00008000)
+#define SCC_GSMRH_TCRC_BISYNC	((uint)0x00004000)
+#define SCC_GSMRH_TCRC_HDLC	((uint)0x00000000)
+#define SCC_GSMRH_REVD		((uint)0x00002000)
+#define SCC_GSMRH_TRX		((uint)0x00001000)
+#define SCC_GSMRH_TTX		((uint)0x00000800)
+#define SCC_GSMRH_CDP		((uint)0x00000400)
+#define SCC_GSMRH_CTSP		((uint)0x00000200)
+#define SCC_GSMRH_CDS		((uint)0x00000100)
+#define SCC_GSMRH_CTSS		((uint)0x00000080)
+#define SCC_GSMRH_TFL		((uint)0x00000040)
+#define SCC_GSMRH_RFW		((uint)0x00000020)
+#define SCC_GSMRH_TXSY		((uint)0x00000010)
+#define SCC_GSMRH_SYNL16	((uint)0x0000000c)
+#define SCC_GSMRH_SYNL8		((uint)0x00000008)
+#define SCC_GSMRH_SYNL4		((uint)0x00000004)
+#define SCC_GSMRH_RTSM		((uint)0x00000002)
+#define SCC_GSMRH_RSYN		((uint)0x00000001)
+
+#define SCC_GSMRL_SIR		((uint)0x80000000)	/* SCC2 only */
+#define SCC_GSMRL_EDGE_NONE	((uint)0x60000000)
+#define SCC_GSMRL_EDGE_NEG	((uint)0x40000000)
+#define SCC_GSMRL_EDGE_POS	((uint)0x20000000)
+#define SCC_GSMRL_EDGE_BOTH	((uint)0x00000000)
+#define SCC_GSMRL_TCI		((uint)0x10000000)
+#define SCC_GSMRL_TSNC_3	((uint)0x0c000000)
+#define SCC_GSMRL_TSNC_4	((uint)0x08000000)
+#define SCC_GSMRL_TSNC_14	((uint)0x04000000)
+#define SCC_GSMRL_TSNC_INF	((uint)0x00000000)
+#define SCC_GSMRL_RINV		((uint)0x02000000)
+#define SCC_GSMRL_TINV		((uint)0x01000000)
+#define SCC_GSMRL_TPL_128	((uint)0x00c00000)
+#define SCC_GSMRL_TPL_64	((uint)0x00a00000)
+#define SCC_GSMRL_TPL_48	((uint)0x00800000)
+#define SCC_GSMRL_TPL_32	((uint)0x00600000)
+#define SCC_GSMRL_TPL_16	((uint)0x00400000)
+#define SCC_GSMRL_TPL_8		((uint)0x00200000)
+#define SCC_GSMRL_TPL_NONE	((uint)0x00000000)
+#define SCC_GSMRL_TPP_ALL1	((uint)0x00180000)
+#define SCC_GSMRL_TPP_01	((uint)0x00100000)
+#define SCC_GSMRL_TPP_10	((uint)0x00080000)
+#define SCC_GSMRL_TPP_ZEROS	((uint)0x00000000)
+#define SCC_GSMRL_TEND		((uint)0x00040000)
+#define SCC_GSMRL_TDCR_32	((uint)0x00030000)
+#define SCC_GSMRL_TDCR_16	((uint)0x00020000)
+#define SCC_GSMRL_TDCR_8	((uint)0x00010000)
+#define SCC_GSMRL_TDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RDCR_32	((uint)0x0000c000)
+#define SCC_GSMRL_RDCR_16	((uint)0x00008000)
+#define SCC_GSMRL_RDCR_8	((uint)0x00004000)
+#define SCC_GSMRL_RDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RENC_DFMAN	((uint)0x00003000)
+#define SCC_GSMRL_RENC_MANCH	((uint)0x00002000)
+#define SCC_GSMRL_RENC_FM0	((uint)0x00001000)
+#define SCC_GSMRL_RENC_NRZI	((uint)0x00000800)
+#define SCC_GSMRL_RENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_TENC_DFMAN	((uint)0x00000600)
+#define SCC_GSMRL_TENC_MANCH	((uint)0x00000400)
+#define SCC_GSMRL_TENC_FM0	((uint)0x00000200)
+#define SCC_GSMRL_TENC_NRZI	((uint)0x00000100)
+#define SCC_GSMRL_TENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_DIAG_LE	((uint)0x000000c0)	/* Loop and echo */
+#define SCC_GSMRL_DIAG_ECHO	((uint)0x00000080)
+#define SCC_GSMRL_DIAG_LOOP	((uint)0x00000040)
+#define SCC_GSMRL_DIAG_NORM	((uint)0x00000000)
+#define SCC_GSMRL_ENR		((uint)0x00000020)
+#define SCC_GSMRL_ENT		((uint)0x00000010)
+#define SCC_GSMRL_MODE_ENET	((uint)0x0000000c)
+#define SCC_GSMRL_MODE_QMC	((uint)0x0000000a)
+#define SCC_GSMRL_MODE_DDCMP	((uint)0x00000009)
+#define SCC_GSMRL_MODE_BISYNC	((uint)0x00000008)
+#define SCC_GSMRL_MODE_V14	((uint)0x00000007)
+#define SCC_GSMRL_MODE_AHDLC	((uint)0x00000006)
+#define SCC_GSMRL_MODE_PROFIBUS	((uint)0x00000005)
+#define SCC_GSMRL_MODE_UART	((uint)0x00000004)
+#define SCC_GSMRL_MODE_SS7	((uint)0x00000003)
+#define SCC_GSMRL_MODE_ATALK	((uint)0x00000002)
+#define SCC_GSMRL_MODE_HDLC	((uint)0x00000000)
+
+#define SCC_TODR_TOD		((ushort)0x8000)
+
+/* SCC Event and Mask register.
+*/
+#define	SCCM_TXE	((unsigned char)0x10)
+#define	SCCM_BSY	((unsigned char)0x04)
+#define	SCCM_TX		((unsigned char)0x02)
+#define	SCCM_RX		((unsigned char)0x01)
+
+typedef struct scc_param {
+	ushort	scc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	scc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	scc_rfcr;	/* Rx function code */
+	u_char	scc_tfcr;	/* Tx function code */
+	ushort	scc_mrblr;	/* Max receive buffer length */
+	uint	scc_rstate;	/* Internal */
+	uint	scc_idp;	/* Internal */
+	ushort	scc_rbptr;	/* Internal */
+	ushort	scc_ibc;	/* Internal */
+	uint	scc_rxtmp;	/* Internal */
+	uint	scc_tstate;	/* Internal */
+	uint	scc_tdp;	/* Internal */
+	ushort	scc_tbptr;	/* Internal */
+	ushort	scc_tbc;	/* Internal */
+	uint	scc_txtmp;	/* Internal */
+	uint	scc_rcrc;	/* Internal */
+	uint	scc_tcrc;	/* Internal */
+} sccp_t;
+
+/* Function code bits.
+*/
+#define SCC_EB	((u_char)0x10)	/* Set big endian byte order */
+
+/* CPM Ethernet through SCCx.
+ */
+typedef struct scc_enet {
+	sccp_t	sen_genscc;
+	uint	sen_cpres;	/* Preset CRC */
+	uint	sen_cmask;	/* Constant mask for CRC */
+	uint	sen_crcec;	/* CRC Error counter */
+	uint	sen_alec;	/* alignment error counter */
+	uint	sen_disfc;	/* discard frame counter */
+	ushort	sen_pads;	/* Tx short frame pad character */
+	ushort	sen_retlim;	/* Retry limit threshold */
+	ushort	sen_retcnt;	/* Retry limit counter */
+	ushort	sen_maxflr;	/* maximum frame length register */
+	ushort	sen_minflr;	/* minimum frame length register */
+	ushort	sen_maxd1;	/* maximum DMA1 length */
+	ushort	sen_maxd2;	/* maximum DMA2 length */
+	ushort	sen_maxd;	/* Rx max DMA */
+	ushort	sen_dmacnt;	/* Rx DMA counter */
+	ushort	sen_maxb;	/* Max BD byte count */
+	ushort	sen_gaddr1;	/* Group address filter */
+	ushort	sen_gaddr2;
+	ushort	sen_gaddr3;
+	ushort	sen_gaddr4;
+	uint	sen_tbuf0data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf0data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf0rba;	/* Internal */
+	uint	sen_tbuf0crc;	/* Internal */
+	ushort	sen_tbuf0bcnt;	/* Internal */
+	ushort	sen_paddrh;	/* physical address (MSB) */
+	ushort	sen_paddrm;
+	ushort	sen_paddrl;	/* physical address (LSB) */
+	ushort	sen_pper;	/* persistence */
+	ushort	sen_rfbdptr;	/* Rx first BD pointer */
+	ushort	sen_tfbdptr;	/* Tx first BD pointer */
+	ushort	sen_tlbdptr;	/* Tx last BD pointer */
+	uint	sen_tbuf1data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf1data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf1rba;	/* Internal */
+	uint	sen_tbuf1crc;	/* Internal */
+	ushort	sen_tbuf1bcnt;	/* Internal */
+	ushort	sen_txlen;	/* Tx Frame length counter */
+	ushort	sen_iaddr1;	/* Individual address filter */
+	ushort	sen_iaddr2;
+	ushort	sen_iaddr3;
+	ushort	sen_iaddr4;
+	ushort	sen_boffcnt;	/* Backoff counter */
+
+	/* NOTE: Some versions of the manual have the following items
+	 * incorrectly documented.  Below is the proper order.
+	 */
+	ushort	sen_taddrh;	/* temp address (MSB) */
+	ushort	sen_taddrm;
+	ushort	sen_taddrl;	/* temp address (LSB) */
+} scc_enet_t;
+
+/* SCC Event register as used by Ethernet.
+*/
+#define SCCE_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
+#define SCCE_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
+#define SCCE_ENET_RXF	((ushort)0x0008)	/* Full frame received */
+#define SCCE_ENET_BSY	((ushort)0x0004)	/* All incoming buffers full */
+#define SCCE_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
+#define SCCE_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
+
+/* SCC Mode Register (PMSR) as used by Ethernet.
+*/
+#define SCC_PSMR_HBC	((ushort)0x8000)	/* Enable heartbeat */
+#define SCC_PSMR_FC	((ushort)0x4000)	/* Force collision */
+#define SCC_PSMR_RSH	((ushort)0x2000)	/* Receive short frames */
+#define SCC_PSMR_IAM	((ushort)0x1000)	/* Check individual hash */
+#define SCC_PSMR_ENCRC	((ushort)0x0800)	/* Ethernet CRC mode */
+#define SCC_PSMR_PRO	((ushort)0x0200)	/* Promiscuous mode */
+#define SCC_PSMR_BRO	((ushort)0x0100)	/* Catch broadcast pkts */
+#define SCC_PSMR_SBT	((ushort)0x0080)	/* Special backoff timer */
+#define SCC_PSMR_LPB	((ushort)0x0040)	/* Set Loopback mode */
+#define SCC_PSMR_SIP	((ushort)0x0020)	/* Sample Input Pins */
+#define SCC_PSMR_LCW	((ushort)0x0010)	/* Late collision window */
+#define SCC_PSMR_NIB22	((ushort)0x000a)	/* Start frame search */
+#define SCC_PSMR_FDE	((ushort)0x0001)	/* Full duplex enable */
+
+/* Buffer descriptor control/status used by Ethernet receive.
+*/
+#define BD_ENET_RX_EMPTY	((ushort)0x8000)
+#define BD_ENET_RX_WRAP		((ushort)0x2000)
+#define BD_ENET_RX_INTR		((ushort)0x1000)
+#define BD_ENET_RX_LAST		((ushort)0x0800)
+#define BD_ENET_RX_FIRST	((ushort)0x0400)
+#define BD_ENET_RX_MISS		((ushort)0x0100)
+#define BD_ENET_RX_LG		((ushort)0x0020)
+#define BD_ENET_RX_NO		((ushort)0x0010)
+#define BD_ENET_RX_SH		((ushort)0x0008)
+#define BD_ENET_RX_CR		((ushort)0x0004)
+#define BD_ENET_RX_OV		((ushort)0x0002)
+#define BD_ENET_RX_CL		((ushort)0x0001)
+#define BD_ENET_RX_BC		((ushort)0x0080)	/* DA is Broadcast */
+#define BD_ENET_RX_MC		((ushort)0x0040)	/* DA is Multicast */
+#define BD_ENET_RX_STATS	((ushort)0x013f)	/* All status bits */
+
+/* Buffer descriptor control/status used by Ethernet transmit.
+*/
+#define BD_ENET_TX_READY	((ushort)0x8000)
+#define BD_ENET_TX_PAD		((ushort)0x4000)
+#define BD_ENET_TX_WRAP		((ushort)0x2000)
+#define BD_ENET_TX_INTR		((ushort)0x1000)
+#define BD_ENET_TX_LAST		((ushort)0x0800)
+#define BD_ENET_TX_TC		((ushort)0x0400)
+#define BD_ENET_TX_DEF		((ushort)0x0200)
+#define BD_ENET_TX_HB		((ushort)0x0100)
+#define BD_ENET_TX_LC		((ushort)0x0080)
+#define BD_ENET_TX_RL		((ushort)0x0040)
+#define BD_ENET_TX_RCMASK	((ushort)0x003c)
+#define BD_ENET_TX_UN		((ushort)0x0002)
+#define BD_ENET_TX_CSL		((ushort)0x0001)
+#define BD_ENET_TX_STATS	((ushort)0x03ff)	/* All status bits */
+
+/* SCC as UART
+*/
+typedef struct scc_uart {
+	sccp_t	scc_genscc;
+	char	res1[8];	/* Reserved */
+	ushort	scc_maxidl;	/* Maximum idle chars */
+	ushort	scc_idlc;	/* temp idle counter */
+	ushort	scc_brkcr;	/* Break count register */
+	ushort	scc_parec;	/* receive parity error counter */
+	ushort	scc_frmec;	/* receive framing error counter */
+	ushort	scc_nosec;	/* receive noise counter */
+	ushort	scc_brkec;	/* receive break condition counter */
+	ushort	scc_brkln;	/* last received break length */
+	ushort	scc_uaddr1;	/* UART address character 1 */
+	ushort	scc_uaddr2;	/* UART address character 2 */
+	ushort	scc_rtemp;	/* Temp storage */
+	ushort	scc_toseq;	/* Transmit out of sequence char */
+	ushort	scc_char1;	/* control character 1 */
+	ushort	scc_char2;	/* control character 2 */
+	ushort	scc_char3;	/* control character 3 */
+	ushort	scc_char4;	/* control character 4 */
+	ushort	scc_char5;	/* control character 5 */
+	ushort	scc_char6;	/* control character 6 */
+	ushort	scc_char7;	/* control character 7 */
+	ushort	scc_char8;	/* control character 8 */
+	ushort	scc_rccm;	/* receive control character mask */
+	ushort	scc_rccr;	/* receive control character register */
+	ushort	scc_rlbc;	/* receive last break character */
+} scc_uart_t;
+
+/* SCC Event and Mask registers when it is used as a UART.
+*/
+#define UART_SCCM_GLR		((ushort)0x1000)
+#define UART_SCCM_GLT		((ushort)0x0800)
+#define UART_SCCM_AB		((ushort)0x0200)
+#define UART_SCCM_IDL		((ushort)0x0100)
+#define UART_SCCM_GRA		((ushort)0x0080)
+#define UART_SCCM_BRKE		((ushort)0x0040)
+#define UART_SCCM_BRKS		((ushort)0x0020)
+#define UART_SCCM_CCR		((ushort)0x0008)
+#define UART_SCCM_BSY		((ushort)0x0004)
+#define UART_SCCM_TX		((ushort)0x0002)
+#define UART_SCCM_RX		((ushort)0x0001)
+
+/* The SCC PMSR when used as a UART.
+*/
+#define SCU_PSMR_FLC		((ushort)0x8000)
+#define SCU_PSMR_SL		((ushort)0x4000)
+#define SCU_PSMR_CL		((ushort)0x3000)
+#define SCU_PSMR_UM		((ushort)0x0c00)
+#define SCU_PSMR_FRZ		((ushort)0x0200)
+#define SCU_PSMR_RZS		((ushort)0x0100)
+#define SCU_PSMR_SYN		((ushort)0x0080)
+#define SCU_PSMR_DRT		((ushort)0x0040)
+#define SCU_PSMR_PEN		((ushort)0x0010)
+#define SCU_PSMR_RPM		((ushort)0x000c)
+#define SCU_PSMR_REVP		((ushort)0x0008)
+#define SCU_PSMR_TPM		((ushort)0x0003)
+#define SCU_PSMR_TEVP		((ushort)0x0002)
+
+/* CPM Transparent mode SCC.
+ */
+typedef struct scc_trans {
+	sccp_t	st_genscc;
+	uint	st_cpres;	/* Preset CRC */
+	uint	st_cmask;	/* Constant mask for CRC */
+} scc_trans_t;
+
+#define BD_SCC_TX_LAST		((ushort)0x0800)
+
+/* IIC parameter RAM.
+*/
+typedef struct iic {
+	ushort	iic_rbase;	/* Rx Buffer descriptor base address */
+	ushort	iic_tbase;	/* Tx Buffer descriptor base address */
+	u_char	iic_rfcr;	/* Rx function code */
+	u_char	iic_tfcr;	/* Tx function code */
+	ushort	iic_mrblr;	/* Max receive buffer length */
+	uint	iic_rstate;	/* Internal */
+	uint	iic_rdp;	/* Internal */
+	ushort	iic_rbptr;	/* Internal */
+	ushort	iic_rbc;	/* Internal */
+	uint	iic_rxtmp;	/* Internal */
+	uint	iic_tstate;	/* Internal */
+	uint	iic_tdp;	/* Internal */
+	ushort	iic_tbptr;	/* Internal */
+	ushort	iic_tbc;	/* Internal */
+	uint	iic_txtmp;	/* Internal */
+	char	res1[4];	/* Reserved */
+	ushort	iic_rpbase;	/* Relocation pointer */
+	char	res2[2];	/* Reserved */
+} iic_t;
+
+#define BD_IIC_START		((ushort)0x0400)
+
+/* SPI parameter RAM.
+*/
+typedef struct spi {
+	ushort	spi_rbase;	/* Rx Buffer descriptor base address */
+	ushort	spi_tbase;	/* Tx Buffer descriptor base address */
+	u_char	spi_rfcr;	/* Rx function code */
+	u_char	spi_tfcr;	/* Tx function code */
+	ushort	spi_mrblr;	/* Max receive buffer length */
+	uint	spi_rstate;	/* Internal */
+	uint	spi_rdp;	/* Internal */
+	ushort	spi_rbptr;	/* Internal */
+	ushort	spi_rbc;	/* Internal */
+	uint	spi_rxtmp;	/* Internal */
+	uint	spi_tstate;	/* Internal */
+	uint	spi_tdp;	/* Internal */
+	ushort	spi_tbptr;	/* Internal */
+	ushort	spi_tbc;	/* Internal */
+	uint	spi_txtmp;	/* Internal */
+	uint	spi_res;
+	ushort	spi_rpbase;	/* Relocation pointer */
+	ushort	spi_res2;
+} spi_t;
+
+/* SPI Mode register.
+*/
+#define SPMODE_LOOP	((ushort)0x4000)	/* Loopback */
+#define SPMODE_CI	((ushort)0x2000)	/* Clock Invert */
+#define SPMODE_CP	((ushort)0x1000)	/* Clock Phase */
+#define SPMODE_DIV16	((ushort)0x0800)	/* BRG/16 mode */
+#define SPMODE_REV	((ushort)0x0400)	/* Reversed Data */
+#define SPMODE_MSTR	((ushort)0x0200)	/* SPI Master */
+#define SPMODE_EN	((ushort)0x0100)	/* Enable */
+#define SPMODE_LENMSK	((ushort)0x00f0)	/* character length */
+#define SPMODE_LEN4	((ushort)0x0030)	/*  4 bits per char */
+#define SPMODE_LEN8	((ushort)0x0070)	/*  8 bits per char */
+#define SPMODE_LEN16	((ushort)0x00f0)	/* 16 bits per char */
+#define SPMODE_PMMSK	((ushort)0x000f)	/* prescale modulus */
+
+/* SPIE fields */
+#define SPIE_MME	0x20
+#define SPIE_TXE	0x10
+#define SPIE_BSY	0x04
+#define SPIE_TXB	0x02
+#define SPIE_RXB	0x01
+
+/*
+ * RISC Controller Configuration Register definitons
+ */
+#define RCCR_TIME	0x8000			/* RISC Timer Enable */
+#define RCCR_TIMEP(t)	(((t) & 0x3F)<<8)	/* RISC Timer Period */
+#define RCCR_TIME_MASK	0x00FF			/* not RISC Timer related bits */
+
+/* RISC Timer Parameter RAM offset */
+#define PROFF_RTMR	((uint)0x01B0)
+
+typedef struct risc_timer_pram {
+	unsigned short	tm_base;	/* RISC Timer Table Base Address */
+	unsigned short	tm_ptr;		/* RISC Timer Table Pointer (internal) */
+	unsigned short	r_tmr;		/* RISC Timer Mode Register */
+	unsigned short	r_tmv;		/* RISC Timer Valid Register */
+	unsigned long	tm_cmd;		/* RISC Timer Command Register */
+	unsigned long	tm_cnt;		/* RISC Timer Internal Count */
+} rt_pram_t;
+
+/* Bits in RISC Timer Command Register */
+#define TM_CMD_VALID	0x80000000	/* Valid - Enables the timer */
+#define TM_CMD_RESTART	0x40000000	/* Restart - for automatic restart */
+#define TM_CMD_PWM	0x20000000	/* Run in Pulse Width Modulation Mode */
+#define TM_CMD_NUM(n)	(((n)&0xF)<<16)	/* Timer Number */
+#define TM_CMD_PERIOD(p) ((p)&0xFFFF)	/* Timer Period */
+
+/* CPM interrupts.  There are nearly 32 interrupts generated by CPM
+ * channels or devices.  All of these are presented to the PPC core
+ * as a single interrupt.  The CPM interrupt handler dispatches its
+ * own handlers, in a similar fashion to the PPC core handler.  We
+ * use the table as defined in the manuals (i.e. no special high
+ * priority and SCC1 == SCCa, etc...).
+ */
+#define CPMVEC_NR		32
+#define	CPMVEC_PIO_PC15		((ushort)0x1f)
+#define	CPMVEC_SCC1		((ushort)0x1e)
+#define	CPMVEC_SCC2		((ushort)0x1d)
+#define	CPMVEC_SCC3		((ushort)0x1c)
+#define	CPMVEC_SCC4		((ushort)0x1b)
+#define	CPMVEC_PIO_PC14		((ushort)0x1a)
+#define	CPMVEC_TIMER1		((ushort)0x19)
+#define	CPMVEC_PIO_PC13		((ushort)0x18)
+#define	CPMVEC_PIO_PC12		((ushort)0x17)
+#define	CPMVEC_SDMA_CB_ERR	((ushort)0x16)
+#define CPMVEC_IDMA1		((ushort)0x15)
+#define CPMVEC_IDMA2		((ushort)0x14)
+#define CPMVEC_TIMER2		((ushort)0x12)
+#define CPMVEC_RISCTIMER	((ushort)0x11)
+#define CPMVEC_I2C		((ushort)0x10)
+#define	CPMVEC_PIO_PC11		((ushort)0x0f)
+#define	CPMVEC_PIO_PC10		((ushort)0x0e)
+#define CPMVEC_TIMER3		((ushort)0x0c)
+#define	CPMVEC_PIO_PC9		((ushort)0x0b)
+#define	CPMVEC_PIO_PC8		((ushort)0x0a)
+#define	CPMVEC_PIO_PC7		((ushort)0x09)
+#define CPMVEC_TIMER4		((ushort)0x07)
+#define	CPMVEC_PIO_PC6		((ushort)0x06)
+#define	CPMVEC_SPI		((ushort)0x05)
+#define	CPMVEC_SMC1		((ushort)0x04)
+#define	CPMVEC_SMC2		((ushort)0x03)
+#define	CPMVEC_PIO_PC5		((ushort)0x02)
+#define	CPMVEC_PIO_PC4		((ushort)0x01)
+#define	CPMVEC_ERROR		((ushort)0x00)
+
+/* CPM interrupt configuration vector.
+*/
+#define	CICR_SCD_SCC4		((uint)0x00c00000)	/* SCC4 @ SCCd */
+#define	CICR_SCC_SCC3		((uint)0x00200000)	/* SCC3 @ SCCc */
+#define	CICR_SCB_SCC2		((uint)0x00040000)	/* SCC2 @ SCCb */
+#define	CICR_SCA_SCC1		((uint)0x00000000)	/* SCC1 @ SCCa */
+#define CICR_IRL_MASK		((uint)0x0000e000)	/* Core interrrupt */
+#define CICR_HP_MASK		((uint)0x00001f00)	/* Hi-pri int. */
+#define CICR_IEN		((uint)0x00000080)	/* Int. enable */
+#define CICR_SPS		((uint)0x00000001)	/* SCC Spread */
+
+extern void cpm_install_handler(int vec, void (*handler)(void *), void *dev_id);
+extern void cpm_free_handler(int vec);
+
+#endif /* __CPM_8XX__ */
diff --git a/include/asm-powerpc/cpm2.h b/include/asm-powerpc/cpm2.h
new file mode 100644
index 0000000..12a2860
--- /dev/null
+++ b/include/asm-powerpc/cpm2.h
@@ -0,0 +1,1248 @@
+/*
+ * Communication Processor Module v2.
+ *
+ * This file contains structures and information for the communication
+ * processor channels found in the dual port RAM or parameter RAM.
+ * All CPM control and status is available through the CPM2 internal
+ * memory map.  See immap_cpm2.h for details.
+ */
+#ifdef __KERNEL__
+#ifndef __CPM2__
+#define __CPM2__
+
+#include <asm/immap_cpm2.h>
+
+/* CPM Command register.
+*/
+#define CPM_CR_RST	((uint)0x80000000)
+#define CPM_CR_PAGE	((uint)0x7c000000)
+#define CPM_CR_SBLOCK	((uint)0x03e00000)
+#define CPM_CR_FLG	((uint)0x00010000)
+#define CPM_CR_MCN	((uint)0x00003fc0)
+#define CPM_CR_OPCODE	((uint)0x0000000f)
+
+/* Device sub-block and page codes.
+*/
+#define CPM_CR_SCC1_SBLOCK	(0x04)
+#define CPM_CR_SCC2_SBLOCK	(0x05)
+#define CPM_CR_SCC3_SBLOCK	(0x06)
+#define CPM_CR_SCC4_SBLOCK	(0x07)
+#define CPM_CR_SMC1_SBLOCK	(0x08)
+#define CPM_CR_SMC2_SBLOCK	(0x09)
+#define CPM_CR_SPI_SBLOCK	(0x0a)
+#define CPM_CR_I2C_SBLOCK	(0x0b)
+#define CPM_CR_TIMER_SBLOCK	(0x0f)
+#define CPM_CR_RAND_SBLOCK	(0x0e)
+#define CPM_CR_FCC1_SBLOCK	(0x10)
+#define CPM_CR_FCC2_SBLOCK	(0x11)
+#define CPM_CR_FCC3_SBLOCK	(0x12)
+#define CPM_CR_IDMA1_SBLOCK	(0x14)
+#define CPM_CR_IDMA2_SBLOCK	(0x15)
+#define CPM_CR_IDMA3_SBLOCK	(0x16)
+#define CPM_CR_IDMA4_SBLOCK	(0x17)
+#define CPM_CR_MCC1_SBLOCK	(0x1c)
+
+#define CPM_CR_FCC_SBLOCK(x)	(x + 0x10)
+
+#define CPM_CR_SCC1_PAGE	(0x00)
+#define CPM_CR_SCC2_PAGE	(0x01)
+#define CPM_CR_SCC3_PAGE	(0x02)
+#define CPM_CR_SCC4_PAGE	(0x03)
+#define CPM_CR_SMC1_PAGE	(0x07)
+#define CPM_CR_SMC2_PAGE	(0x08)
+#define CPM_CR_SPI_PAGE		(0x09)
+#define CPM_CR_I2C_PAGE		(0x0a)
+#define CPM_CR_TIMER_PAGE	(0x0a)
+#define CPM_CR_RAND_PAGE	(0x0a)
+#define CPM_CR_FCC1_PAGE	(0x04)
+#define CPM_CR_FCC2_PAGE	(0x05)
+#define CPM_CR_FCC3_PAGE	(0x06)
+#define CPM_CR_IDMA1_PAGE	(0x07)
+#define CPM_CR_IDMA2_PAGE	(0x08)
+#define CPM_CR_IDMA3_PAGE	(0x09)
+#define CPM_CR_IDMA4_PAGE	(0x0a)
+#define CPM_CR_MCC1_PAGE	(0x07)
+#define CPM_CR_MCC2_PAGE	(0x08)
+
+#define CPM_CR_FCC_PAGE(x)	(x + 0x04)
+
+/* Some opcodes (there are more...later)
+*/
+#define CPM_CR_INIT_TRX		((ushort)0x0000)
+#define CPM_CR_INIT_RX		((ushort)0x0001)
+#define CPM_CR_INIT_TX		((ushort)0x0002)
+#define CPM_CR_HUNT_MODE	((ushort)0x0003)
+#define CPM_CR_STOP_TX		((ushort)0x0004)
+#define CPM_CR_GRA_STOP_TX	((ushort)0x0005)
+#define CPM_CR_RESTART_TX	((ushort)0x0006)
+#define CPM_CR_SET_GADDR	((ushort)0x0008)
+#define CPM_CR_START_IDMA	((ushort)0x0009)
+#define CPM_CR_STOP_IDMA	((ushort)0x000b)
+
+#define mk_cr_cmd(PG, SBC, MCN, OP) \
+	((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
+
+/* Dual Port RAM addresses.  The first 16K is available for almost
+ * any CPM use, so we put the BDs there.  The first 128 bytes are
+ * used for SMC1 and SMC2 parameter RAM, so we start allocating
+ * BDs above that.  All of this must change when we start
+ * downloading RAM microcode.
+ */
+#define CPM_DATAONLY_BASE	((uint)128)
+#define CPM_DP_NOSPACE		((uint)0x7fffffff)
+#if defined(CONFIG_8272) || defined(CONFIG_MPC8555)
+#define CPM_DATAONLY_SIZE	((uint)(8 * 1024) - CPM_DATAONLY_BASE)
+#define CPM_FCC_SPECIAL_BASE	((uint)0x00009000)
+#else
+#define CPM_DATAONLY_SIZE	((uint)(16 * 1024) - CPM_DATAONLY_BASE)
+#define CPM_FCC_SPECIAL_BASE	((uint)0x0000b000)
+#endif
+
+/* The number of pages of host memory we allocate for CPM.  This is
+ * done early in kernel initialization to get physically contiguous
+ * pages.
+ */
+#define NUM_CPM_HOST_PAGES	2
+
+/* Export the base address of the communication processor registers
+ * and dual port ram.
+ */
+extern		cpm_cpm2_t	*cpmp;	 /* Pointer to comm processor */
+
+extern unsigned long cpm_dpalloc(uint size, uint align);
+extern int cpm_dpfree(unsigned long offset);
+extern unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align);
+extern void cpm_dpdump(void);
+extern void *cpm_dpram_addr(unsigned long offset);
+extern void cpm_setbrg(uint brg, uint rate);
+extern void cpm2_fastbrg(uint brg, uint rate, int div16);
+extern void cpm2_reset(void);
+
+
+/* Buffer descriptors used by many of the CPM protocols.
+*/
+typedef struct cpm_buf_desc {
+	ushort	cbd_sc;		/* Status and Control */
+	ushort	cbd_datlen;	/* Data length in buffer */
+	uint	cbd_bufaddr;	/* Buffer address in host memory */
+} cbd_t;
+
+#define BD_SC_EMPTY	((ushort)0x8000)	/* Receive is empty */
+#define BD_SC_READY	((ushort)0x8000)	/* Transmit is ready */
+#define BD_SC_WRAP	((ushort)0x2000)	/* Last buffer descriptor */
+#define BD_SC_INTRPT	((ushort)0x1000)	/* Interrupt on change */
+#define BD_SC_LAST	((ushort)0x0800)	/* Last buffer in frame */
+#define BD_SC_CM	((ushort)0x0200)	/* Continous mode */
+#define BD_SC_ID	((ushort)0x0100)	/* Rec'd too many idles */
+#define BD_SC_P		((ushort)0x0100)	/* xmt preamble */
+#define BD_SC_BR	((ushort)0x0020)	/* Break received */
+#define BD_SC_FR	((ushort)0x0010)	/* Framing error */
+#define BD_SC_PR	((ushort)0x0008)	/* Parity error */
+#define BD_SC_OV	((ushort)0x0002)	/* Overrun */
+#define BD_SC_CD	((ushort)0x0001)	/* ?? */
+
+/* Function code bits, usually generic to devices.
+*/
+#define CPMFCR_GBL	((u_char)0x20)	/* Set memory snooping */
+#define CPMFCR_EB	((u_char)0x10)	/* Set big endian byte order */
+#define CPMFCR_TC2	((u_char)0x04)	/* Transfer code 2 value */
+#define CPMFCR_DTB	((u_char)0x02)	/* Use local bus for data when set */
+#define CPMFCR_BDB	((u_char)0x01)	/* Use local bus for BD when set */
+
+/* Parameter RAM offsets from the base.
+*/
+#define PROFF_SCC1		((uint)0x8000)
+#define PROFF_SCC2		((uint)0x8100)
+#define PROFF_SCC3		((uint)0x8200)
+#define PROFF_SCC4		((uint)0x8300)
+#define PROFF_FCC1		((uint)0x8400)
+#define PROFF_FCC2		((uint)0x8500)
+#define PROFF_FCC3		((uint)0x8600)
+#define PROFF_MCC1		((uint)0x8700)
+#define PROFF_SMC1_BASE		((uint)0x87fc)
+#define PROFF_IDMA1_BASE	((uint)0x87fe)
+#define PROFF_MCC2		((uint)0x8800)
+#define PROFF_SMC2_BASE		((uint)0x88fc)
+#define PROFF_IDMA2_BASE	((uint)0x88fe)
+#define PROFF_SPI_BASE		((uint)0x89fc)
+#define PROFF_IDMA3_BASE	((uint)0x89fe)
+#define PROFF_TIMERS		((uint)0x8ae0)
+#define PROFF_REVNUM		((uint)0x8af0)
+#define PROFF_RAND		((uint)0x8af8)
+#define PROFF_I2C_BASE		((uint)0x8afc)
+#define PROFF_IDMA4_BASE	((uint)0x8afe)
+
+#define PROFF_SCC_SIZE		((uint)0x100)
+#define PROFF_FCC_SIZE		((uint)0x100)
+#define PROFF_SMC_SIZE		((uint)64)
+
+/* The SMCs are relocated to any of the first eight DPRAM pages.
+ * We will fix these at the first locations of DPRAM, until we
+ * get some microcode patches :-).
+ * The parameter ram space for the SMCs is fifty-some bytes, and
+ * they are required to start on a 64 byte boundary.
+ */
+#define PROFF_SMC1	(0)
+#define PROFF_SMC2	(64)
+
+
+/* Define enough so I can at least use the serial port as a UART.
+ */
+typedef struct smc_uart {
+	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	smc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	smc_rfcr;	/* Rx function code */
+	u_char	smc_tfcr;	/* Tx function code */
+	ushort	smc_mrblr;	/* Max receive buffer length */
+	uint	smc_rstate;	/* Internal */
+	uint	smc_idp;	/* Internal */
+	ushort	smc_rbptr;	/* Internal */
+	ushort	smc_ibc;	/* Internal */
+	uint	smc_rxtmp;	/* Internal */
+	uint	smc_tstate;	/* Internal */
+	uint	smc_tdp;	/* Internal */
+	ushort	smc_tbptr;	/* Internal */
+	ushort	smc_tbc;	/* Internal */
+	uint	smc_txtmp;	/* Internal */
+	ushort	smc_maxidl;	/* Maximum idle characters */
+	ushort	smc_tmpidl;	/* Temporary idle counter */
+	ushort	smc_brklen;	/* Last received break length */
+	ushort	smc_brkec;	/* rcv'd break condition counter */
+	ushort	smc_brkcr;	/* xmt break count register */
+	ushort	smc_rmask;	/* Temporary bit mask */
+	uint	smc_stmp;	/* SDMA Temp */
+} smc_uart_t;
+
+/* SMC uart mode register (Internal memory map).
+*/
+#define SMCMR_REN	((ushort)0x0001)
+#define SMCMR_TEN	((ushort)0x0002)
+#define SMCMR_DM	((ushort)0x000c)
+#define SMCMR_SM_GCI	((ushort)0x0000)
+#define SMCMR_SM_UART	((ushort)0x0020)
+#define SMCMR_SM_TRANS	((ushort)0x0030)
+#define SMCMR_SM_MASK	((ushort)0x0030)
+#define SMCMR_PM_EVEN	((ushort)0x0100)	/* Even parity, else odd */
+#define SMCMR_REVD	SMCMR_PM_EVEN
+#define SMCMR_PEN	((ushort)0x0200)	/* Parity enable */
+#define SMCMR_BS	SMCMR_PEN
+#define SMCMR_SL	((ushort)0x0400)	/* Two stops, else one */
+#define SMCR_CLEN_MASK	((ushort)0x7800)	/* Character length */
+#define smcr_mk_clen(C)	(((C) << 11) & SMCR_CLEN_MASK)
+
+/* SMC Event and Mask register.
+*/
+#define SMCM_BRKE       ((unsigned char)0x40)   /* When in UART Mode */
+#define SMCM_BRK        ((unsigned char)0x10)   /* When in UART Mode */
+#define SMCM_TXE	((unsigned char)0x10)
+#define SMCM_BSY	((unsigned char)0x04)
+#define SMCM_TX		((unsigned char)0x02)
+#define SMCM_RX		((unsigned char)0x01)
+
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST		((uint)0x00020000)
+#define CPM_BRG_EN		((uint)0x00010000)
+#define CPM_BRG_EXTC_INT	((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK3_9	((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK5_15	((uint)0x00008000)
+#define CPM_BRG_ATB		((uint)0x00002000)
+#define CPM_BRG_CD_MASK		((uint)0x00001ffe)
+#define CPM_BRG_DIV16		((uint)0x00000001)
+
+/* SCCs.
+*/
+#define SCC_GSMRH_IRP		((uint)0x00040000)
+#define SCC_GSMRH_GDE		((uint)0x00010000)
+#define SCC_GSMRH_TCRC_CCITT	((uint)0x00008000)
+#define SCC_GSMRH_TCRC_BISYNC	((uint)0x00004000)
+#define SCC_GSMRH_TCRC_HDLC	((uint)0x00000000)
+#define SCC_GSMRH_REVD		((uint)0x00002000)
+#define SCC_GSMRH_TRX		((uint)0x00001000)
+#define SCC_GSMRH_TTX		((uint)0x00000800)
+#define SCC_GSMRH_CDP		((uint)0x00000400)
+#define SCC_GSMRH_CTSP		((uint)0x00000200)
+#define SCC_GSMRH_CDS		((uint)0x00000100)
+#define SCC_GSMRH_CTSS		((uint)0x00000080)
+#define SCC_GSMRH_TFL		((uint)0x00000040)
+#define SCC_GSMRH_RFW		((uint)0x00000020)
+#define SCC_GSMRH_TXSY		((uint)0x00000010)
+#define SCC_GSMRH_SYNL16	((uint)0x0000000c)
+#define SCC_GSMRH_SYNL8		((uint)0x00000008)
+#define SCC_GSMRH_SYNL4		((uint)0x00000004)
+#define SCC_GSMRH_RTSM		((uint)0x00000002)
+#define SCC_GSMRH_RSYN		((uint)0x00000001)
+
+#define SCC_GSMRL_SIR		((uint)0x80000000)	/* SCC2 only */
+#define SCC_GSMRL_EDGE_NONE	((uint)0x60000000)
+#define SCC_GSMRL_EDGE_NEG	((uint)0x40000000)
+#define SCC_GSMRL_EDGE_POS	((uint)0x20000000)
+#define SCC_GSMRL_EDGE_BOTH	((uint)0x00000000)
+#define SCC_GSMRL_TCI		((uint)0x10000000)
+#define SCC_GSMRL_TSNC_3	((uint)0x0c000000)
+#define SCC_GSMRL_TSNC_4	((uint)0x08000000)
+#define SCC_GSMRL_TSNC_14	((uint)0x04000000)
+#define SCC_GSMRL_TSNC_INF	((uint)0x00000000)
+#define SCC_GSMRL_RINV		((uint)0x02000000)
+#define SCC_GSMRL_TINV		((uint)0x01000000)
+#define SCC_GSMRL_TPL_128	((uint)0x00c00000)
+#define SCC_GSMRL_TPL_64	((uint)0x00a00000)
+#define SCC_GSMRL_TPL_48	((uint)0x00800000)
+#define SCC_GSMRL_TPL_32	((uint)0x00600000)
+#define SCC_GSMRL_TPL_16	((uint)0x00400000)
+#define SCC_GSMRL_TPL_8		((uint)0x00200000)
+#define SCC_GSMRL_TPL_NONE	((uint)0x00000000)
+#define SCC_GSMRL_TPP_ALL1	((uint)0x00180000)
+#define SCC_GSMRL_TPP_01	((uint)0x00100000)
+#define SCC_GSMRL_TPP_10	((uint)0x00080000)
+#define SCC_GSMRL_TPP_ZEROS	((uint)0x00000000)
+#define SCC_GSMRL_TEND		((uint)0x00040000)
+#define SCC_GSMRL_TDCR_32	((uint)0x00030000)
+#define SCC_GSMRL_TDCR_16	((uint)0x00020000)
+#define SCC_GSMRL_TDCR_8	((uint)0x00010000)
+#define SCC_GSMRL_TDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RDCR_32	((uint)0x0000c000)
+#define SCC_GSMRL_RDCR_16	((uint)0x00008000)
+#define SCC_GSMRL_RDCR_8	((uint)0x00004000)
+#define SCC_GSMRL_RDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RENC_DFMAN	((uint)0x00003000)
+#define SCC_GSMRL_RENC_MANCH	((uint)0x00002000)
+#define SCC_GSMRL_RENC_FM0	((uint)0x00001000)
+#define SCC_GSMRL_RENC_NRZI	((uint)0x00000800)
+#define SCC_GSMRL_RENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_TENC_DFMAN	((uint)0x00000600)
+#define SCC_GSMRL_TENC_MANCH	((uint)0x00000400)
+#define SCC_GSMRL_TENC_FM0	((uint)0x00000200)
+#define SCC_GSMRL_TENC_NRZI	((uint)0x00000100)
+#define SCC_GSMRL_TENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_DIAG_LE	((uint)0x000000c0)	/* Loop and echo */
+#define SCC_GSMRL_DIAG_ECHO	((uint)0x00000080)
+#define SCC_GSMRL_DIAG_LOOP	((uint)0x00000040)
+#define SCC_GSMRL_DIAG_NORM	((uint)0x00000000)
+#define SCC_GSMRL_ENR		((uint)0x00000020)
+#define SCC_GSMRL_ENT		((uint)0x00000010)
+#define SCC_GSMRL_MODE_ENET	((uint)0x0000000c)
+#define SCC_GSMRL_MODE_DDCMP	((uint)0x00000009)
+#define SCC_GSMRL_MODE_BISYNC	((uint)0x00000008)
+#define SCC_GSMRL_MODE_V14	((uint)0x00000007)
+#define SCC_GSMRL_MODE_AHDLC	((uint)0x00000006)
+#define SCC_GSMRL_MODE_PROFIBUS	((uint)0x00000005)
+#define SCC_GSMRL_MODE_UART	((uint)0x00000004)
+#define SCC_GSMRL_MODE_SS7	((uint)0x00000003)
+#define SCC_GSMRL_MODE_ATALK	((uint)0x00000002)
+#define SCC_GSMRL_MODE_HDLC	((uint)0x00000000)
+
+#define SCC_TODR_TOD		((ushort)0x8000)
+
+/* SCC Event and Mask register.
+*/
+#define SCCM_TXE	((unsigned char)0x10)
+#define SCCM_BSY	((unsigned char)0x04)
+#define SCCM_TX		((unsigned char)0x02)
+#define SCCM_RX		((unsigned char)0x01)
+
+typedef struct scc_param {
+	ushort	scc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	scc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	scc_rfcr;	/* Rx function code */
+	u_char	scc_tfcr;	/* Tx function code */
+	ushort	scc_mrblr;	/* Max receive buffer length */
+	uint	scc_rstate;	/* Internal */
+	uint	scc_idp;	/* Internal */
+	ushort	scc_rbptr;	/* Internal */
+	ushort	scc_ibc;	/* Internal */
+	uint	scc_rxtmp;	/* Internal */
+	uint	scc_tstate;	/* Internal */
+	uint	scc_tdp;	/* Internal */
+	ushort	scc_tbptr;	/* Internal */
+	ushort	scc_tbc;	/* Internal */
+	uint	scc_txtmp;	/* Internal */
+	uint	scc_rcrc;	/* Internal */
+	uint	scc_tcrc;	/* Internal */
+} sccp_t;
+
+/* CPM Ethernet through SCC1.
+ */
+typedef struct scc_enet {
+	sccp_t	sen_genscc;
+	uint	sen_cpres;	/* Preset CRC */
+	uint	sen_cmask;	/* Constant mask for CRC */
+	uint	sen_crcec;	/* CRC Error counter */
+	uint	sen_alec;	/* alignment error counter */
+	uint	sen_disfc;	/* discard frame counter */
+	ushort	sen_pads;	/* Tx short frame pad character */
+	ushort	sen_retlim;	/* Retry limit threshold */
+	ushort	sen_retcnt;	/* Retry limit counter */
+	ushort	sen_maxflr;	/* maximum frame length register */
+	ushort	sen_minflr;	/* minimum frame length register */
+	ushort	sen_maxd1;	/* maximum DMA1 length */
+	ushort	sen_maxd2;	/* maximum DMA2 length */
+	ushort	sen_maxd;	/* Rx max DMA */
+	ushort	sen_dmacnt;	/* Rx DMA counter */
+	ushort	sen_maxb;	/* Max BD byte count */
+	ushort	sen_gaddr1;	/* Group address filter */
+	ushort	sen_gaddr2;
+	ushort	sen_gaddr3;
+	ushort	sen_gaddr4;
+	uint	sen_tbuf0data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf0data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf0rba;	/* Internal */
+	uint	sen_tbuf0crc;	/* Internal */
+	ushort	sen_tbuf0bcnt;	/* Internal */
+	ushort	sen_paddrh;	/* physical address (MSB) */
+	ushort	sen_paddrm;
+	ushort	sen_paddrl;	/* physical address (LSB) */
+	ushort	sen_pper;	/* persistence */
+	ushort	sen_rfbdptr;	/* Rx first BD pointer */
+	ushort	sen_tfbdptr;	/* Tx first BD pointer */
+	ushort	sen_tlbdptr;	/* Tx last BD pointer */
+	uint	sen_tbuf1data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf1data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf1rba;	/* Internal */
+	uint	sen_tbuf1crc;	/* Internal */
+	ushort	sen_tbuf1bcnt;	/* Internal */
+	ushort	sen_txlen;	/* Tx Frame length counter */
+	ushort	sen_iaddr1;	/* Individual address filter */
+	ushort	sen_iaddr2;
+	ushort	sen_iaddr3;
+	ushort	sen_iaddr4;
+	ushort	sen_boffcnt;	/* Backoff counter */
+
+	/* NOTE: Some versions of the manual have the following items
+	 * incorrectly documented.  Below is the proper order.
+	 */
+	ushort	sen_taddrh;	/* temp address (MSB) */
+	ushort	sen_taddrm;
+	ushort	sen_taddrl;	/* temp address (LSB) */
+} scc_enet_t;
+
+
+/* SCC Event register as used by Ethernet.
+*/
+#define SCCE_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
+#define SCCE_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
+#define SCCE_ENET_RXF	((ushort)0x0008)	/* Full frame received */
+#define SCCE_ENET_BSY	((ushort)0x0004)	/* All incoming buffers full */
+#define SCCE_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
+#define SCCE_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
+
+/* SCC Mode Register (PSMR) as used by Ethernet.
+*/
+#define SCC_PSMR_HBC	((ushort)0x8000)	/* Enable heartbeat */
+#define SCC_PSMR_FC	((ushort)0x4000)	/* Force collision */
+#define SCC_PSMR_RSH	((ushort)0x2000)	/* Receive short frames */
+#define SCC_PSMR_IAM	((ushort)0x1000)	/* Check individual hash */
+#define SCC_PSMR_ENCRC	((ushort)0x0800)	/* Ethernet CRC mode */
+#define SCC_PSMR_PRO	((ushort)0x0200)	/* Promiscuous mode */
+#define SCC_PSMR_BRO	((ushort)0x0100)	/* Catch broadcast pkts */
+#define SCC_PSMR_SBT	((ushort)0x0080)	/* Special backoff timer */
+#define SCC_PSMR_LPB	((ushort)0x0040)	/* Set Loopback mode */
+#define SCC_PSMR_SIP	((ushort)0x0020)	/* Sample Input Pins */
+#define SCC_PSMR_LCW	((ushort)0x0010)	/* Late collision window */
+#define SCC_PSMR_NIB22	((ushort)0x000a)	/* Start frame search */
+#define SCC_PSMR_FDE	((ushort)0x0001)	/* Full duplex enable */
+
+/* Buffer descriptor control/status used by Ethernet receive.
+ * Common to SCC and FCC.
+ */
+#define BD_ENET_RX_EMPTY	((ushort)0x8000)
+#define BD_ENET_RX_WRAP		((ushort)0x2000)
+#define BD_ENET_RX_INTR		((ushort)0x1000)
+#define BD_ENET_RX_LAST		((ushort)0x0800)
+#define BD_ENET_RX_FIRST	((ushort)0x0400)
+#define BD_ENET_RX_MISS		((ushort)0x0100)
+#define BD_ENET_RX_BC		((ushort)0x0080)	/* FCC Only */
+#define BD_ENET_RX_MC		((ushort)0x0040)	/* FCC Only */
+#define BD_ENET_RX_LG		((ushort)0x0020)
+#define BD_ENET_RX_NO		((ushort)0x0010)
+#define BD_ENET_RX_SH		((ushort)0x0008)
+#define BD_ENET_RX_CR		((ushort)0x0004)
+#define BD_ENET_RX_OV		((ushort)0x0002)
+#define BD_ENET_RX_CL		((ushort)0x0001)
+#define BD_ENET_RX_STATS	((ushort)0x01ff)	/* All status bits */
+
+/* Buffer descriptor control/status used by Ethernet transmit.
+ * Common to SCC and FCC.
+ */
+#define BD_ENET_TX_READY	((ushort)0x8000)
+#define BD_ENET_TX_PAD		((ushort)0x4000)
+#define BD_ENET_TX_WRAP		((ushort)0x2000)
+#define BD_ENET_TX_INTR		((ushort)0x1000)
+#define BD_ENET_TX_LAST		((ushort)0x0800)
+#define BD_ENET_TX_TC		((ushort)0x0400)
+#define BD_ENET_TX_DEF		((ushort)0x0200)
+#define BD_ENET_TX_HB		((ushort)0x0100)
+#define BD_ENET_TX_LC		((ushort)0x0080)
+#define BD_ENET_TX_RL		((ushort)0x0040)
+#define BD_ENET_TX_RCMASK	((ushort)0x003c)
+#define BD_ENET_TX_UN		((ushort)0x0002)
+#define BD_ENET_TX_CSL		((ushort)0x0001)
+#define BD_ENET_TX_STATS	((ushort)0x03ff)	/* All status bits */
+
+/* SCC as UART
+*/
+typedef struct scc_uart {
+	sccp_t	scc_genscc;
+	uint	scc_res1;	/* Reserved */
+	uint	scc_res2;	/* Reserved */
+	ushort	scc_maxidl;	/* Maximum idle chars */
+	ushort	scc_idlc;	/* temp idle counter */
+	ushort	scc_brkcr;	/* Break count register */
+	ushort	scc_parec;	/* receive parity error counter */
+	ushort	scc_frmec;	/* receive framing error counter */
+	ushort	scc_nosec;	/* receive noise counter */
+	ushort	scc_brkec;	/* receive break condition counter */
+	ushort	scc_brkln;	/* last received break length */
+	ushort	scc_uaddr1;	/* UART address character 1 */
+	ushort	scc_uaddr2;	/* UART address character 2 */
+	ushort	scc_rtemp;	/* Temp storage */
+	ushort	scc_toseq;	/* Transmit out of sequence char */
+	ushort	scc_char1;	/* control character 1 */
+	ushort	scc_char2;	/* control character 2 */
+	ushort	scc_char3;	/* control character 3 */
+	ushort	scc_char4;	/* control character 4 */
+	ushort	scc_char5;	/* control character 5 */
+	ushort	scc_char6;	/* control character 6 */
+	ushort	scc_char7;	/* control character 7 */
+	ushort	scc_char8;	/* control character 8 */
+	ushort	scc_rccm;	/* receive control character mask */
+	ushort	scc_rccr;	/* receive control character register */
+	ushort	scc_rlbc;	/* receive last break character */
+} scc_uart_t;
+
+/* SCC Event and Mask registers when it is used as a UART.
+*/
+#define UART_SCCM_GLR		((ushort)0x1000)
+#define UART_SCCM_GLT		((ushort)0x0800)
+#define UART_SCCM_AB		((ushort)0x0200)
+#define UART_SCCM_IDL		((ushort)0x0100)
+#define UART_SCCM_GRA		((ushort)0x0080)
+#define UART_SCCM_BRKE		((ushort)0x0040)
+#define UART_SCCM_BRKS		((ushort)0x0020)
+#define UART_SCCM_CCR		((ushort)0x0008)
+#define UART_SCCM_BSY		((ushort)0x0004)
+#define UART_SCCM_TX		((ushort)0x0002)
+#define UART_SCCM_RX		((ushort)0x0001)
+
+/* The SCC PSMR when used as a UART.
+*/
+#define SCU_PSMR_FLC		((ushort)0x8000)
+#define SCU_PSMR_SL		((ushort)0x4000)
+#define SCU_PSMR_CL		((ushort)0x3000)
+#define SCU_PSMR_UM		((ushort)0x0c00)
+#define SCU_PSMR_FRZ		((ushort)0x0200)
+#define SCU_PSMR_RZS		((ushort)0x0100)
+#define SCU_PSMR_SYN		((ushort)0x0080)
+#define SCU_PSMR_DRT		((ushort)0x0040)
+#define SCU_PSMR_PEN		((ushort)0x0010)
+#define SCU_PSMR_RPM		((ushort)0x000c)
+#define SCU_PSMR_REVP		((ushort)0x0008)
+#define SCU_PSMR_TPM		((ushort)0x0003)
+#define SCU_PSMR_TEVP		((ushort)0x0002)
+
+/* CPM Transparent mode SCC.
+ */
+typedef struct scc_trans {
+	sccp_t	st_genscc;
+	uint	st_cpres;	/* Preset CRC */
+	uint	st_cmask;	/* Constant mask for CRC */
+} scc_trans_t;
+
+#define BD_SCC_TX_LAST		((ushort)0x0800)
+
+/* How about some FCCs.....
+*/
+#define FCC_GFMR_DIAG_NORM	((uint)0x00000000)
+#define FCC_GFMR_DIAG_LE	((uint)0x40000000)
+#define FCC_GFMR_DIAG_AE	((uint)0x80000000)
+#define FCC_GFMR_DIAG_ALE	((uint)0xc0000000)
+#define FCC_GFMR_TCI		((uint)0x20000000)
+#define FCC_GFMR_TRX		((uint)0x10000000)
+#define FCC_GFMR_TTX		((uint)0x08000000)
+#define FCC_GFMR_TTX		((uint)0x08000000)
+#define FCC_GFMR_CDP		((uint)0x04000000)
+#define FCC_GFMR_CTSP		((uint)0x02000000)
+#define FCC_GFMR_CDS		((uint)0x01000000)
+#define FCC_GFMR_CTSS		((uint)0x00800000)
+#define FCC_GFMR_SYNL_NONE	((uint)0x00000000)
+#define FCC_GFMR_SYNL_AUTO	((uint)0x00004000)
+#define FCC_GFMR_SYNL_8		((uint)0x00008000)
+#define FCC_GFMR_SYNL_16	((uint)0x0000c000)
+#define FCC_GFMR_RTSM		((uint)0x00002000)
+#define FCC_GFMR_RENC_NRZ	((uint)0x00000000)
+#define FCC_GFMR_RENC_NRZI	((uint)0x00000800)
+#define FCC_GFMR_REVD		((uint)0x00000400)
+#define FCC_GFMR_TENC_NRZ	((uint)0x00000000)
+#define FCC_GFMR_TENC_NRZI	((uint)0x00000100)
+#define FCC_GFMR_TCRC_16	((uint)0x00000000)
+#define FCC_GFMR_TCRC_32	((uint)0x00000080)
+#define FCC_GFMR_ENR		((uint)0x00000020)
+#define FCC_GFMR_ENT		((uint)0x00000010)
+#define FCC_GFMR_MODE_ENET	((uint)0x0000000c)
+#define FCC_GFMR_MODE_ATM	((uint)0x0000000a)
+#define FCC_GFMR_MODE_HDLC	((uint)0x00000000)
+
+/* Generic FCC parameter ram.
+*/
+typedef struct fcc_param {
+	ushort	fcc_riptr;	/* Rx Internal temp pointer */
+	ushort	fcc_tiptr;	/* Tx Internal temp pointer */
+	ushort	fcc_res1;
+	ushort	fcc_mrblr;	/* Max receive buffer length, mod 32 bytes */
+	uint	fcc_rstate;	/* Upper byte is Func code, must be set */
+	uint	fcc_rbase;	/* Receive BD base */
+	ushort	fcc_rbdstat;	/* RxBD status */
+	ushort	fcc_rbdlen;	/* RxBD down counter */
+	uint	fcc_rdptr;	/* RxBD internal data pointer */
+	uint	fcc_tstate;	/* Upper byte is Func code, must be set */
+	uint	fcc_tbase;	/* Transmit BD base */
+	ushort	fcc_tbdstat;	/* TxBD status */
+	ushort	fcc_tbdlen;	/* TxBD down counter */
+	uint	fcc_tdptr;	/* TxBD internal data pointer */
+	uint	fcc_rbptr;	/* Rx BD Internal buf pointer */
+	uint	fcc_tbptr;	/* Tx BD Internal buf pointer */
+	uint	fcc_rcrc;	/* Rx temp CRC */
+	uint	fcc_res2;
+	uint	fcc_tcrc;	/* Tx temp CRC */
+} fccp_t;
+
+
+/* Ethernet controller through FCC.
+*/
+typedef struct fcc_enet {
+	fccp_t	fen_genfcc;
+	uint	fen_statbuf;	/* Internal status buffer */
+	uint	fen_camptr;	/* CAM address */
+	uint	fen_cmask;	/* Constant mask for CRC */
+	uint	fen_cpres;	/* Preset CRC */
+	uint	fen_crcec;	/* CRC Error counter */
+	uint	fen_alec;	/* alignment error counter */
+	uint	fen_disfc;	/* discard frame counter */
+	ushort	fen_retlim;	/* Retry limit */
+	ushort	fen_retcnt;	/* Retry counter */
+	ushort	fen_pper;	/* Persistence */
+	ushort	fen_boffcnt;	/* backoff counter */
+	uint	fen_gaddrh;	/* Group address filter, high 32-bits */
+	uint	fen_gaddrl;	/* Group address filter, low 32-bits */
+	ushort	fen_tfcstat;	/* out of sequence TxBD */
+	ushort	fen_tfclen;
+	uint	fen_tfcptr;
+	ushort	fen_mflr;	/* Maximum frame length (1518) */
+	ushort	fen_paddrh;	/* MAC address */
+	ushort	fen_paddrm;
+	ushort	fen_paddrl;
+	ushort	fen_ibdcount;	/* Internal BD counter */
+	ushort	fen_ibdstart;	/* Internal BD start pointer */
+	ushort	fen_ibdend;	/* Internal BD end pointer */
+	ushort	fen_txlen;	/* Internal Tx frame length counter */
+	uint	fen_ibdbase[8]; /* Internal use */
+	uint	fen_iaddrh;	/* Individual address filter */
+	uint	fen_iaddrl;
+	ushort	fen_minflr;	/* Minimum frame length (64) */
+	ushort	fen_taddrh;	/* Filter transfer MAC address */
+	ushort	fen_taddrm;
+	ushort	fen_taddrl;
+	ushort	fen_padptr;	/* Pointer to pad byte buffer */
+	ushort	fen_cftype;	/* control frame type */
+	ushort	fen_cfrange;	/* control frame range */
+	ushort	fen_maxb;	/* maximum BD count */
+	ushort	fen_maxd1;	/* Max DMA1 length (1520) */
+	ushort	fen_maxd2;	/* Max DMA2 length (1520) */
+	ushort	fen_maxd;	/* internal max DMA count */
+	ushort	fen_dmacnt;	/* internal DMA counter */
+	uint	fen_octc;	/* Total octect counter */
+	uint	fen_colc;	/* Total collision counter */
+	uint	fen_broc;	/* Total broadcast packet counter */
+	uint	fen_mulc;	/* Total multicast packet count */
+	uint	fen_uspc;	/* Total packets < 64 bytes */
+	uint	fen_frgc;	/* Total packets < 64 bytes with errors */
+	uint	fen_ospc;	/* Total packets > 1518 */
+	uint	fen_jbrc;	/* Total packets > 1518 with errors */
+	uint	fen_p64c;	/* Total packets == 64 bytes */
+	uint	fen_p65c;	/* Total packets 64 < bytes <= 127 */
+	uint	fen_p128c;	/* Total packets 127 < bytes <= 255 */
+	uint	fen_p256c;	/* Total packets 256 < bytes <= 511 */
+	uint	fen_p512c;	/* Total packets 512 < bytes <= 1023 */
+	uint	fen_p1024c;	/* Total packets 1024 < bytes <= 1518 */
+	uint	fen_cambuf;	/* Internal CAM buffer poiner */
+	ushort	fen_rfthr;	/* Received frames threshold */
+	ushort	fen_rfcnt;	/* Received frames count */
+} fcc_enet_t;
+
+/* FCC Event/Mask register as used by Ethernet.
+*/
+#define FCC_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
+#define FCC_ENET_RXC	((ushort)0x0040)	/* Control Frame Received */
+#define FCC_ENET_TXC	((ushort)0x0020)	/* Out of seq. Tx sent */
+#define FCC_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
+#define FCC_ENET_RXF	((ushort)0x0008)	/* Full frame received */
+#define FCC_ENET_BSY	((ushort)0x0004)	/* Busy.  Rx Frame dropped */
+#define FCC_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
+#define FCC_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
+
+/* FCC Mode Register (FPSMR) as used by Ethernet.
+*/
+#define FCC_PSMR_HBC	((uint)0x80000000)	/* Enable heartbeat */
+#define FCC_PSMR_FC	((uint)0x40000000)	/* Force Collision */
+#define FCC_PSMR_SBT	((uint)0x20000000)	/* Stop backoff timer */
+#define FCC_PSMR_LPB	((uint)0x10000000)	/* Local protect. 1 = FDX */
+#define FCC_PSMR_LCW	((uint)0x08000000)	/* Late collision select */
+#define FCC_PSMR_FDE	((uint)0x04000000)	/* Full Duplex Enable */
+#define FCC_PSMR_MON	((uint)0x02000000)	/* RMON Enable */
+#define FCC_PSMR_PRO	((uint)0x00400000)	/* Promiscuous Enable */
+#define FCC_PSMR_FCE	((uint)0x00200000)	/* Flow Control Enable */
+#define FCC_PSMR_RSH	((uint)0x00100000)	/* Receive Short Frames */
+#define FCC_PSMR_CAM	((uint)0x00000400)	/* CAM enable */
+#define FCC_PSMR_BRO	((uint)0x00000200)	/* Broadcast pkt discard */
+#define FCC_PSMR_ENCRC	((uint)0x00000080)	/* Use 32-bit CRC */
+
+/* IIC parameter RAM.
+*/
+typedef struct iic {
+	ushort	iic_rbase;	/* Rx Buffer descriptor base address */
+	ushort	iic_tbase;	/* Tx Buffer descriptor base address */
+	u_char	iic_rfcr;	/* Rx function code */
+	u_char	iic_tfcr;	/* Tx function code */
+	ushort	iic_mrblr;	/* Max receive buffer length */
+	uint	iic_rstate;	/* Internal */
+	uint	iic_rdp;	/* Internal */
+	ushort	iic_rbptr;	/* Internal */
+	ushort	iic_rbc;	/* Internal */
+	uint	iic_rxtmp;	/* Internal */
+	uint	iic_tstate;	/* Internal */
+	uint	iic_tdp;	/* Internal */
+	ushort	iic_tbptr;	/* Internal */
+	ushort	iic_tbc;	/* Internal */
+	uint	iic_txtmp;	/* Internal */
+} iic_t;
+
+/* SPI parameter RAM.
+*/
+typedef struct spi {
+	ushort	spi_rbase;	/* Rx Buffer descriptor base address */
+	ushort	spi_tbase;	/* Tx Buffer descriptor base address */
+	u_char	spi_rfcr;	/* Rx function code */
+	u_char	spi_tfcr;	/* Tx function code */
+	ushort	spi_mrblr;	/* Max receive buffer length */
+	uint	spi_rstate;	/* Internal */
+	uint	spi_rdp;	/* Internal */
+	ushort	spi_rbptr;	/* Internal */
+	ushort	spi_rbc;	/* Internal */
+	uint	spi_rxtmp;	/* Internal */
+	uint	spi_tstate;	/* Internal */
+	uint	spi_tdp;	/* Internal */
+	ushort	spi_tbptr;	/* Internal */
+	ushort	spi_tbc;	/* Internal */
+	uint	spi_txtmp;	/* Internal */
+	uint	spi_res;	/* Tx temp. */
+	uint	spi_res1[4];	/* SDMA temp. */
+} spi_t;
+
+/* SPI Mode register.
+*/
+#define SPMODE_LOOP	((ushort)0x4000)	/* Loopback */
+#define SPMODE_CI	((ushort)0x2000)	/* Clock Invert */
+#define SPMODE_CP	((ushort)0x1000)	/* Clock Phase */
+#define SPMODE_DIV16	((ushort)0x0800)	/* BRG/16 mode */
+#define SPMODE_REV	((ushort)0x0400)	/* Reversed Data */
+#define SPMODE_MSTR	((ushort)0x0200)	/* SPI Master */
+#define SPMODE_EN	((ushort)0x0100)	/* Enable */
+#define SPMODE_LENMSK	((ushort)0x00f0)	/* character length */
+#define SPMODE_PMMSK	((ushort)0x000f)	/* prescale modulus */
+
+#define SPMODE_LEN(x)	((((x)-1)&0xF)<<4)
+#define SPMODE_PM(x)	((x) &0xF)
+
+#define SPI_EB		((u_char)0x10)		/* big endian byte order */
+
+#define BD_IIC_START		((ushort)0x0400)
+
+/* IDMA parameter RAM
+*/
+typedef struct idma {
+	ushort ibase;		/* IDMA buffer descriptor table base address */
+	ushort dcm;		/* DMA channel mode */
+	ushort ibdptr;		/* IDMA current buffer descriptor pointer */
+	ushort dpr_buf;		/* IDMA transfer buffer base address */
+	ushort buf_inv;		/* internal buffer inventory */
+	ushort ss_max;		/* steady-state maximum transfer size */
+	ushort dpr_in_ptr;	/* write pointer inside the internal buffer */
+	ushort sts;		/* source transfer size */
+	ushort dpr_out_ptr;	/* read pointer inside the internal buffer */
+	ushort seob;		/* source end of burst */
+	ushort deob;		/* destination end of burst */
+	ushort dts;		/* destination transfer size */
+	ushort ret_add;		/* return address when working in ERM=1 mode */
+	ushort res0;		/* reserved */
+	uint   bd_cnt;		/* internal byte count */
+	uint   s_ptr;		/* source internal data pointer */
+	uint   d_ptr;		/* destination internal data pointer */
+	uint   istate;		/* internal state */
+	u_char res1[20];	/* pad to 64-byte length */
+} idma_t;
+
+/* DMA channel mode bit fields
+*/
+#define IDMA_DCM_FB		((ushort)0x8000) /* fly-by mode */
+#define IDMA_DCM_LP		((ushort)0x4000) /* low priority */
+#define IDMA_DCM_TC2		((ushort)0x0400) /* value driven on TC[2] */
+#define IDMA_DCM_DMA_WRAP_MASK	((ushort)0x01c0) /* mask for DMA wrap */
+#define IDMA_DCM_DMA_WRAP_64	((ushort)0x0000) /* 64-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_128	((ushort)0x0040) /* 128-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_256	((ushort)0x0080) /* 256-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_512	((ushort)0x00c0) /* 512-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_1024	((ushort)0x0100) /* 1024-byte DMA xfer buffer */
+#define IDMA_DCM_DMA_WRAP_2048	((ushort)0x0140) /* 2048-byte DMA xfer buffer */
+#define IDMA_DCM_SINC		((ushort)0x0020) /* source inc addr */
+#define IDMA_DCM_DINC		((ushort)0x0010) /* destination inc addr */
+#define IDMA_DCM_ERM		((ushort)0x0008) /* external request mode */
+#define IDMA_DCM_DT		((ushort)0x0004) /* DONE treatment */
+#define IDMA_DCM_SD_MASK	((ushort)0x0003) /* mask for SD bit field */
+#define IDMA_DCM_SD_MEM2MEM	((ushort)0x0000) /* memory-to-memory xfer */
+#define IDMA_DCM_SD_PER2MEM	((ushort)0x0002) /* peripheral-to-memory xfer */
+#define IDMA_DCM_SD_MEM2PER	((ushort)0x0001) /* memory-to-peripheral xfer */
+
+/* IDMA Buffer Descriptors
+*/
+typedef struct idma_bd {
+	uint flags;
+	uint len;	/* data length */
+	uint src;	/* source data buffer pointer */
+	uint dst;	/* destination data buffer pointer */
+} idma_bd_t;
+
+/* IDMA buffer descriptor flag bit fields
+*/
+#define IDMA_BD_V	((uint)0x80000000)	/* valid */
+#define IDMA_BD_W	((uint)0x20000000)	/* wrap */
+#define IDMA_BD_I	((uint)0x10000000)	/* interrupt */
+#define IDMA_BD_L	((uint)0x08000000)	/* last */
+#define IDMA_BD_CM	((uint)0x02000000)	/* continuous mode */
+#define IDMA_BD_SDN	((uint)0x00400000)	/* source done */
+#define IDMA_BD_DDN	((uint)0x00200000)	/* destination done */
+#define IDMA_BD_DGBL	((uint)0x00100000)	/* destination global */
+#define IDMA_BD_DBO_LE	((uint)0x00040000)	/* little-end dest byte order */
+#define IDMA_BD_DBO_BE	((uint)0x00080000)	/* big-end dest byte order */
+#define IDMA_BD_DDTB	((uint)0x00010000)	/* destination data bus */
+#define IDMA_BD_SGBL	((uint)0x00002000)	/* source global */
+#define IDMA_BD_SBO_LE	((uint)0x00000800)	/* little-end src byte order */
+#define IDMA_BD_SBO_BE	((uint)0x00001000)	/* big-end src byte order */
+#define IDMA_BD_SDTB	((uint)0x00000200)	/* source data bus */
+
+/* per-channel IDMA registers
+*/
+typedef struct im_idma {
+	u_char idsr;			/* IDMAn event status register */
+	u_char res0[3];
+	u_char idmr;			/* IDMAn event mask register */
+	u_char res1[3];
+} im_idma_t;
+
+/* IDMA event register bit fields
+*/
+#define IDMA_EVENT_SC	((unsigned char)0x08)	/* stop completed */
+#define IDMA_EVENT_OB	((unsigned char)0x04)	/* out of buffers */
+#define IDMA_EVENT_EDN	((unsigned char)0x02)	/* external DONE asserted */
+#define IDMA_EVENT_BC	((unsigned char)0x01)	/* buffer descriptor complete */
+
+/* RISC Controller Configuration Register (RCCR) bit fields
+*/
+#define RCCR_TIME	((uint)0x80000000) /* timer enable */
+#define RCCR_TIMEP_MASK	((uint)0x3f000000) /* mask for timer period bit field */
+#define RCCR_DR0M	((uint)0x00800000) /* IDMA0 request mode */
+#define RCCR_DR1M	((uint)0x00400000) /* IDMA1 request mode */
+#define RCCR_DR2M	((uint)0x00000080) /* IDMA2 request mode */
+#define RCCR_DR3M	((uint)0x00000040) /* IDMA3 request mode */
+#define RCCR_DR0QP_MASK	((uint)0x00300000) /* mask for IDMA0 req priority */
+#define RCCR_DR0QP_HIGH ((uint)0x00000000) /* IDMA0 has high req priority */
+#define RCCR_DR0QP_MED	((uint)0x00100000) /* IDMA0 has medium req priority */
+#define RCCR_DR0QP_LOW	((uint)0x00200000) /* IDMA0 has low req priority */
+#define RCCR_DR1QP_MASK	((uint)0x00030000) /* mask for IDMA1 req priority */
+#define RCCR_DR1QP_HIGH ((uint)0x00000000) /* IDMA1 has high req priority */
+#define RCCR_DR1QP_MED	((uint)0x00010000) /* IDMA1 has medium req priority */
+#define RCCR_DR1QP_LOW	((uint)0x00020000) /* IDMA1 has low req priority */
+#define RCCR_DR2QP_MASK	((uint)0x00000030) /* mask for IDMA2 req priority */
+#define RCCR_DR2QP_HIGH ((uint)0x00000000) /* IDMA2 has high req priority */
+#define RCCR_DR2QP_MED	((uint)0x00000010) /* IDMA2 has medium req priority */
+#define RCCR_DR2QP_LOW	((uint)0x00000020) /* IDMA2 has low req priority */
+#define RCCR_DR3QP_MASK	((uint)0x00000003) /* mask for IDMA3 req priority */
+#define RCCR_DR3QP_HIGH ((uint)0x00000000) /* IDMA3 has high req priority */
+#define RCCR_DR3QP_MED	((uint)0x00000001) /* IDMA3 has medium req priority */
+#define RCCR_DR3QP_LOW	((uint)0x00000002) /* IDMA3 has low req priority */
+#define RCCR_EIE	((uint)0x00080000) /* external interrupt enable */
+#define RCCR_SCD	((uint)0x00040000) /* scheduler configuration */
+#define RCCR_ERAM_MASK	((uint)0x0000e000) /* mask for enable RAM microcode */
+#define RCCR_ERAM_0KB	((uint)0x00000000) /* use 0KB of dpram for microcode */
+#define RCCR_ERAM_2KB	((uint)0x00002000) /* use 2KB of dpram for microcode */
+#define RCCR_ERAM_4KB	((uint)0x00004000) /* use 4KB of dpram for microcode */
+#define RCCR_ERAM_6KB	((uint)0x00006000) /* use 6KB of dpram for microcode */
+#define RCCR_ERAM_8KB	((uint)0x00008000) /* use 8KB of dpram for microcode */
+#define RCCR_ERAM_10KB	((uint)0x0000a000) /* use 10KB of dpram for microcode */
+#define RCCR_ERAM_12KB	((uint)0x0000c000) /* use 12KB of dpram for microcode */
+#define RCCR_EDM0	((uint)0x00000800) /* DREQ0 edge detect mode */
+#define RCCR_EDM1	((uint)0x00000400) /* DREQ1 edge detect mode */
+#define RCCR_EDM2	((uint)0x00000200) /* DREQ2 edge detect mode */
+#define RCCR_EDM3	((uint)0x00000100) /* DREQ3 edge detect mode */
+#define RCCR_DEM01	((uint)0x00000008) /* DONE0/DONE1 edge detect mode */
+#define RCCR_DEM23	((uint)0x00000004) /* DONE2/DONE3 edge detect mode */
+
+/*-----------------------------------------------------------------------
+ * CMXFCR - CMX FCC Clock Route Register
+ */
+#define CMXFCR_FC1         0x40000000   /* FCC1 connection              */
+#define CMXFCR_RF1CS_MSK   0x38000000   /* Receive FCC1 Clock Source Mask */
+#define CMXFCR_TF1CS_MSK   0x07000000   /* Transmit FCC1 Clock Source Mask */
+#define CMXFCR_FC2         0x00400000   /* FCC2 connection              */
+#define CMXFCR_RF2CS_MSK   0x00380000   /* Receive FCC2 Clock Source Mask */
+#define CMXFCR_TF2CS_MSK   0x00070000   /* Transmit FCC2 Clock Source Mask */
+#define CMXFCR_FC3         0x00004000   /* FCC3 connection              */
+#define CMXFCR_RF3CS_MSK   0x00003800   /* Receive FCC3 Clock Source Mask */
+#define CMXFCR_TF3CS_MSK   0x00000700   /* Transmit FCC3 Clock Source Mask */
+
+#define CMXFCR_RF1CS_BRG5  0x00000000   /* Receive FCC1 Clock Source is BRG5 */
+#define CMXFCR_RF1CS_BRG6  0x08000000   /* Receive FCC1 Clock Source is BRG6 */
+#define CMXFCR_RF1CS_BRG7  0x10000000   /* Receive FCC1 Clock Source is BRG7 */
+#define CMXFCR_RF1CS_BRG8  0x18000000   /* Receive FCC1 Clock Source is BRG8 */
+#define CMXFCR_RF1CS_CLK9  0x20000000   /* Receive FCC1 Clock Source is CLK9 */
+#define CMXFCR_RF1CS_CLK10 0x28000000   /* Receive FCC1 Clock Source is CLK10 */
+#define CMXFCR_RF1CS_CLK11 0x30000000   /* Receive FCC1 Clock Source is CLK11 */
+#define CMXFCR_RF1CS_CLK12 0x38000000   /* Receive FCC1 Clock Source is CLK12 */
+
+#define CMXFCR_TF1CS_BRG5  0x00000000   /* Transmit FCC1 Clock Source is BRG5 */
+#define CMXFCR_TF1CS_BRG6  0x01000000   /* Transmit FCC1 Clock Source is BRG6 */
+#define CMXFCR_TF1CS_BRG7  0x02000000   /* Transmit FCC1 Clock Source is BRG7 */
+#define CMXFCR_TF1CS_BRG8  0x03000000   /* Transmit FCC1 Clock Source is BRG8 */
+#define CMXFCR_TF1CS_CLK9  0x04000000   /* Transmit FCC1 Clock Source is CLK9 */
+#define CMXFCR_TF1CS_CLK10 0x05000000   /* Transmit FCC1 Clock Source is CLK10 */
+#define CMXFCR_TF1CS_CLK11 0x06000000   /* Transmit FCC1 Clock Source is CLK11 */
+#define CMXFCR_TF1CS_CLK12 0x07000000   /* Transmit FCC1 Clock Source is CLK12 */
+
+#define CMXFCR_RF2CS_BRG5  0x00000000   /* Receive FCC2 Clock Source is BRG5 */
+#define CMXFCR_RF2CS_BRG6  0x00080000   /* Receive FCC2 Clock Source is BRG6 */
+#define CMXFCR_RF2CS_BRG7  0x00100000   /* Receive FCC2 Clock Source is BRG7 */
+#define CMXFCR_RF2CS_BRG8  0x00180000   /* Receive FCC2 Clock Source is BRG8 */
+#define CMXFCR_RF2CS_CLK13 0x00200000   /* Receive FCC2 Clock Source is CLK13 */
+#define CMXFCR_RF2CS_CLK14 0x00280000   /* Receive FCC2 Clock Source is CLK14 */
+#define CMXFCR_RF2CS_CLK15 0x00300000   /* Receive FCC2 Clock Source is CLK15 */
+#define CMXFCR_RF2CS_CLK16 0x00380000   /* Receive FCC2 Clock Source is CLK16 */
+
+#define CMXFCR_TF2CS_BRG5  0x00000000   /* Transmit FCC2 Clock Source is BRG5 */
+#define CMXFCR_TF2CS_BRG6  0x00010000   /* Transmit FCC2 Clock Source is BRG6 */
+#define CMXFCR_TF2CS_BRG7  0x00020000   /* Transmit FCC2 Clock Source is BRG7 */
+#define CMXFCR_TF2CS_BRG8  0x00030000   /* Transmit FCC2 Clock Source is BRG8 */
+#define CMXFCR_TF2CS_CLK13 0x00040000   /* Transmit FCC2 Clock Source is CLK13 */
+#define CMXFCR_TF2CS_CLK14 0x00050000   /* Transmit FCC2 Clock Source is CLK14 */
+#define CMXFCR_TF2CS_CLK15 0x00060000   /* Transmit FCC2 Clock Source is CLK15 */
+#define CMXFCR_TF2CS_CLK16 0x00070000   /* Transmit FCC2 Clock Source is CLK16 */
+
+#define CMXFCR_RF3CS_BRG5  0x00000000   /* Receive FCC3 Clock Source is BRG5 */
+#define CMXFCR_RF3CS_BRG6  0x00000800   /* Receive FCC3 Clock Source is BRG6 */
+#define CMXFCR_RF3CS_BRG7  0x00001000   /* Receive FCC3 Clock Source is BRG7 */
+#define CMXFCR_RF3CS_BRG8  0x00001800   /* Receive FCC3 Clock Source is BRG8 */
+#define CMXFCR_RF3CS_CLK13 0x00002000   /* Receive FCC3 Clock Source is CLK13 */
+#define CMXFCR_RF3CS_CLK14 0x00002800   /* Receive FCC3 Clock Source is CLK14 */
+#define CMXFCR_RF3CS_CLK15 0x00003000   /* Receive FCC3 Clock Source is CLK15 */
+#define CMXFCR_RF3CS_CLK16 0x00003800   /* Receive FCC3 Clock Source is CLK16 */
+
+#define CMXFCR_TF3CS_BRG5  0x00000000   /* Transmit FCC3 Clock Source is BRG5 */
+#define CMXFCR_TF3CS_BRG6  0x00000100   /* Transmit FCC3 Clock Source is BRG6 */
+#define CMXFCR_TF3CS_BRG7  0x00000200   /* Transmit FCC3 Clock Source is BRG7 */
+#define CMXFCR_TF3CS_BRG8  0x00000300   /* Transmit FCC3 Clock Source is BRG8 */
+#define CMXFCR_TF3CS_CLK13 0x00000400   /* Transmit FCC3 Clock Source is CLK13 */
+#define CMXFCR_TF3CS_CLK14 0x00000500   /* Transmit FCC3 Clock Source is CLK14 */
+#define CMXFCR_TF3CS_CLK15 0x00000600   /* Transmit FCC3 Clock Source is CLK15 */
+#define CMXFCR_TF3CS_CLK16 0x00000700   /* Transmit FCC3 Clock Source is CLK16 */
+
+/*-----------------------------------------------------------------------
+ * CMXSCR - CMX SCC Clock Route Register
+ */
+#define CMXSCR_GR1         0x80000000   /* Grant Support of SCC1        */
+#define CMXSCR_SC1         0x40000000   /* SCC1 connection              */
+#define CMXSCR_RS1CS_MSK   0x38000000   /* Receive SCC1 Clock Source Mask */
+#define CMXSCR_TS1CS_MSK   0x07000000   /* Transmit SCC1 Clock Source Mask */
+#define CMXSCR_GR2         0x00800000   /* Grant Support of SCC2        */
+#define CMXSCR_SC2         0x00400000   /* SCC2 connection              */
+#define CMXSCR_RS2CS_MSK   0x00380000   /* Receive SCC2 Clock Source Mask */
+#define CMXSCR_TS2CS_MSK   0x00070000   /* Transmit SCC2 Clock Source Mask */
+#define CMXSCR_GR3         0x00008000   /* Grant Support of SCC3        */
+#define CMXSCR_SC3         0x00004000   /* SCC3 connection              */
+#define CMXSCR_RS3CS_MSK   0x00003800   /* Receive SCC3 Clock Source Mask */
+#define CMXSCR_TS3CS_MSK   0x00000700   /* Transmit SCC3 Clock Source Mask */
+#define CMXSCR_GR4         0x00000080   /* Grant Support of SCC4        */
+#define CMXSCR_SC4         0x00000040   /* SCC4 connection              */
+#define CMXSCR_RS4CS_MSK   0x00000038   /* Receive SCC4 Clock Source Mask */
+#define CMXSCR_TS4CS_MSK   0x00000007   /* Transmit SCC4 Clock Source Mask */
+
+#define CMXSCR_RS1CS_BRG1  0x00000000   /* SCC1 Rx Clock Source is BRG1 */
+#define CMXSCR_RS1CS_BRG2  0x08000000   /* SCC1 Rx Clock Source is BRG2 */
+#define CMXSCR_RS1CS_BRG3  0x10000000   /* SCC1 Rx Clock Source is BRG3 */
+#define CMXSCR_RS1CS_BRG4  0x18000000   /* SCC1 Rx Clock Source is BRG4 */
+#define CMXSCR_RS1CS_CLK11 0x20000000   /* SCC1 Rx Clock Source is CLK11 */
+#define CMXSCR_RS1CS_CLK12 0x28000000   /* SCC1 Rx Clock Source is CLK12 */
+#define CMXSCR_RS1CS_CLK3  0x30000000   /* SCC1 Rx Clock Source is CLK3 */
+#define CMXSCR_RS1CS_CLK4  0x38000000   /* SCC1 Rx Clock Source is CLK4 */
+
+#define CMXSCR_TS1CS_BRG1  0x00000000   /* SCC1 Tx Clock Source is BRG1 */
+#define CMXSCR_TS1CS_BRG2  0x01000000   /* SCC1 Tx Clock Source is BRG2 */
+#define CMXSCR_TS1CS_BRG3  0x02000000   /* SCC1 Tx Clock Source is BRG3 */
+#define CMXSCR_TS1CS_BRG4  0x03000000   /* SCC1 Tx Clock Source is BRG4 */
+#define CMXSCR_TS1CS_CLK11 0x04000000   /* SCC1 Tx Clock Source is CLK11 */
+#define CMXSCR_TS1CS_CLK12 0x05000000   /* SCC1 Tx Clock Source is CLK12 */
+#define CMXSCR_TS1CS_CLK3  0x06000000   /* SCC1 Tx Clock Source is CLK3 */
+#define CMXSCR_TS1CS_CLK4  0x07000000   /* SCC1 Tx Clock Source is CLK4 */
+
+#define CMXSCR_RS2CS_BRG1  0x00000000   /* SCC2 Rx Clock Source is BRG1 */
+#define CMXSCR_RS2CS_BRG2  0x00080000   /* SCC2 Rx Clock Source is BRG2 */
+#define CMXSCR_RS2CS_BRG3  0x00100000   /* SCC2 Rx Clock Source is BRG3 */
+#define CMXSCR_RS2CS_BRG4  0x00180000   /* SCC2 Rx Clock Source is BRG4 */
+#define CMXSCR_RS2CS_CLK11 0x00200000   /* SCC2 Rx Clock Source is CLK11 */
+#define CMXSCR_RS2CS_CLK12 0x00280000   /* SCC2 Rx Clock Source is CLK12 */
+#define CMXSCR_RS2CS_CLK3  0x00300000   /* SCC2 Rx Clock Source is CLK3 */
+#define CMXSCR_RS2CS_CLK4  0x00380000   /* SCC2 Rx Clock Source is CLK4 */
+
+#define CMXSCR_TS2CS_BRG1  0x00000000   /* SCC2 Tx Clock Source is BRG1 */
+#define CMXSCR_TS2CS_BRG2  0x00010000   /* SCC2 Tx Clock Source is BRG2 */
+#define CMXSCR_TS2CS_BRG3  0x00020000   /* SCC2 Tx Clock Source is BRG3 */
+#define CMXSCR_TS2CS_BRG4  0x00030000   /* SCC2 Tx Clock Source is BRG4 */
+#define CMXSCR_TS2CS_CLK11 0x00040000   /* SCC2 Tx Clock Source is CLK11 */
+#define CMXSCR_TS2CS_CLK12 0x00050000   /* SCC2 Tx Clock Source is CLK12 */
+#define CMXSCR_TS2CS_CLK3  0x00060000   /* SCC2 Tx Clock Source is CLK3 */
+#define CMXSCR_TS2CS_CLK4  0x00070000   /* SCC2 Tx Clock Source is CLK4 */
+
+#define CMXSCR_RS3CS_BRG1  0x00000000   /* SCC3 Rx Clock Source is BRG1 */
+#define CMXSCR_RS3CS_BRG2  0x00000800   /* SCC3 Rx Clock Source is BRG2 */
+#define CMXSCR_RS3CS_BRG3  0x00001000   /* SCC3 Rx Clock Source is BRG3 */
+#define CMXSCR_RS3CS_BRG4  0x00001800   /* SCC3 Rx Clock Source is BRG4 */
+#define CMXSCR_RS3CS_CLK5  0x00002000   /* SCC3 Rx Clock Source is CLK5 */
+#define CMXSCR_RS3CS_CLK6  0x00002800   /* SCC3 Rx Clock Source is CLK6 */
+#define CMXSCR_RS3CS_CLK7  0x00003000   /* SCC3 Rx Clock Source is CLK7 */
+#define CMXSCR_RS3CS_CLK8  0x00003800   /* SCC3 Rx Clock Source is CLK8 */
+
+#define CMXSCR_TS3CS_BRG1  0x00000000   /* SCC3 Tx Clock Source is BRG1 */
+#define CMXSCR_TS3CS_BRG2  0x00000100   /* SCC3 Tx Clock Source is BRG2 */
+#define CMXSCR_TS3CS_BRG3  0x00000200   /* SCC3 Tx Clock Source is BRG3 */
+#define CMXSCR_TS3CS_BRG4  0x00000300   /* SCC3 Tx Clock Source is BRG4 */
+#define CMXSCR_TS3CS_CLK5  0x00000400   /* SCC3 Tx Clock Source is CLK5 */
+#define CMXSCR_TS3CS_CLK6  0x00000500   /* SCC3 Tx Clock Source is CLK6 */
+#define CMXSCR_TS3CS_CLK7  0x00000600   /* SCC3 Tx Clock Source is CLK7 */
+#define CMXSCR_TS3CS_CLK8  0x00000700   /* SCC3 Tx Clock Source is CLK8 */
+
+#define CMXSCR_RS4CS_BRG1  0x00000000   /* SCC4 Rx Clock Source is BRG1 */
+#define CMXSCR_RS4CS_BRG2  0x00000008   /* SCC4 Rx Clock Source is BRG2 */
+#define CMXSCR_RS4CS_BRG3  0x00000010   /* SCC4 Rx Clock Source is BRG3 */
+#define CMXSCR_RS4CS_BRG4  0x00000018   /* SCC4 Rx Clock Source is BRG4 */
+#define CMXSCR_RS4CS_CLK5  0x00000020   /* SCC4 Rx Clock Source is CLK5 */
+#define CMXSCR_RS4CS_CLK6  0x00000028   /* SCC4 Rx Clock Source is CLK6 */
+#define CMXSCR_RS4CS_CLK7  0x00000030   /* SCC4 Rx Clock Source is CLK7 */
+#define CMXSCR_RS4CS_CLK8  0x00000038   /* SCC4 Rx Clock Source is CLK8 */
+
+#define CMXSCR_TS4CS_BRG1  0x00000000   /* SCC4 Tx Clock Source is BRG1 */
+#define CMXSCR_TS4CS_BRG2  0x00000001   /* SCC4 Tx Clock Source is BRG2 */
+#define CMXSCR_TS4CS_BRG3  0x00000002   /* SCC4 Tx Clock Source is BRG3 */
+#define CMXSCR_TS4CS_BRG4  0x00000003   /* SCC4 Tx Clock Source is BRG4 */
+#define CMXSCR_TS4CS_CLK5  0x00000004   /* SCC4 Tx Clock Source is CLK5 */
+#define CMXSCR_TS4CS_CLK6  0x00000005   /* SCC4 Tx Clock Source is CLK6 */
+#define CMXSCR_TS4CS_CLK7  0x00000006   /* SCC4 Tx Clock Source is CLK7 */
+#define CMXSCR_TS4CS_CLK8  0x00000007   /* SCC4 Tx Clock Source is CLK8 */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration Register				 4-31
+ */
+#define SIUMCR_BBD	0x80000000	/* Bus Busy Disable		*/
+#define SIUMCR_ESE	0x40000000	/* External Snoop Enable	*/
+#define SIUMCR_PBSE	0x20000000	/* Parity Byte Select Enable	*/
+#define SIUMCR_CDIS	0x10000000	/* Core Disable			*/
+#define SIUMCR_DPPC00	0x00000000	/* Data Parity Pins Configuration*/
+#define SIUMCR_DPPC01	0x04000000	/* - " -			*/
+#define SIUMCR_DPPC10	0x08000000	/* - " -			*/
+#define SIUMCR_DPPC11	0x0c000000	/* - " -			*/
+#define SIUMCR_L2CPC00	0x00000000	/* L2 Cache Pins Configuration	*/
+#define SIUMCR_L2CPC01	0x01000000	/* - " -			*/
+#define SIUMCR_L2CPC10	0x02000000	/* - " -			*/
+#define SIUMCR_L2CPC11	0x03000000	/* - " -			*/
+#define SIUMCR_LBPC00	0x00000000	/* Local Bus Pins Configuration	*/
+#define SIUMCR_LBPC01	0x00400000	/* - " -			*/
+#define SIUMCR_LBPC10	0x00800000	/* - " -			*/
+#define SIUMCR_LBPC11	0x00c00000	/* - " -			*/
+#define SIUMCR_APPC00	0x00000000	/* Address Parity Pins Configuration*/
+#define SIUMCR_APPC01	0x00100000	/* - " -			*/
+#define SIUMCR_APPC10	0x00200000	/* - " -			*/
+#define SIUMCR_APPC11	0x00300000	/* - " -			*/
+#define SIUMCR_CS10PC00	0x00000000	/* CS10 Pin Configuration	*/
+#define SIUMCR_CS10PC01	0x00040000	/* - " -			*/
+#define SIUMCR_CS10PC10	0x00080000	/* - " -			*/
+#define SIUMCR_CS10PC11	0x000c0000	/* - " -			*/
+#define SIUMCR_BCTLC00	0x00000000	/* Buffer Control Configuration	*/
+#define SIUMCR_BCTLC01	0x00010000	/* - " -			*/
+#define SIUMCR_BCTLC10	0x00020000	/* - " -			*/
+#define SIUMCR_BCTLC11	0x00030000	/* - " -			*/
+#define SIUMCR_MMR00	0x00000000	/* Mask Masters Requests	*/
+#define SIUMCR_MMR01	0x00004000	/* - " -			*/
+#define SIUMCR_MMR10	0x00008000	/* - " -			*/
+#define SIUMCR_MMR11	0x0000c000	/* - " -			*/
+#define SIUMCR_LPBSE	0x00002000	/* LocalBus Parity Byte Select Enable*/
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control Register					 9-8
+*/
+#define SCCR_PCI_MODE	0x00000100	/* PCI Mode	*/
+#define SCCR_PCI_MODCK	0x00000080	/* Value of PCI_MODCK pin	*/
+#define SCCR_PCIDF_MSK	0x00000078	/* PCI division factor	*/
+#define SCCR_PCIDF_SHIFT 3
+
+#ifndef CPM_IMMR_OFFSET
+#define CPM_IMMR_OFFSET	0x101a8
+#endif
+
+#define FCC_PSMR_RMII	((uint)0x00020000)	/* Use RMII interface */
+
+/* FCC iop & clock configuration. BSP code is responsible to define Fx_RXCLK & Fx_TXCLK
+ * in order to use clock-computing stuff below for the FCC x
+ */
+
+/* Automatically generates register configurations */
+#define PC_CLK(x)	((uint)(1<<(x-1)))	/* FCC CLK I/O ports */
+
+#define CMXFCR_RF1CS(x)	((uint)((x-5)<<27))	/* FCC1 Receive Clock Source */
+#define CMXFCR_TF1CS(x)	((uint)((x-5)<<24))	/* FCC1 Transmit Clock Source */
+#define CMXFCR_RF2CS(x)	((uint)((x-9)<<19))	/* FCC2 Receive Clock Source */
+#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16))	/* FCC2 Transmit Clock Source */
+#define CMXFCR_RF3CS(x)	((uint)((x-9)<<11))	/* FCC3 Receive Clock Source */
+#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8))	/* FCC3 Transmit Clock Source */
+
+#define PC_F1RXCLK	PC_CLK(F1_RXCLK)
+#define PC_F1TXCLK	PC_CLK(F1_TXCLK)
+#define CMX1_CLK_ROUTE	(CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
+#define CMX1_CLK_MASK	((uint)0xff000000)
+
+#define PC_F2RXCLK	PC_CLK(F2_RXCLK)
+#define PC_F2TXCLK	PC_CLK(F2_TXCLK)
+#define CMX2_CLK_ROUTE	(CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
+#define CMX2_CLK_MASK	((uint)0x00ff0000)
+
+#define PC_F3RXCLK	PC_CLK(F3_RXCLK)
+#define PC_F3TXCLK	PC_CLK(F3_TXCLK)
+#define CMX3_CLK_ROUTE	(CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
+#define CMX3_CLK_MASK	((uint)0x0000ff00)
+
+#define CPMUX_CLK_MASK (CMX3_CLK_MASK | CMX2_CLK_MASK)
+#define CPMUX_CLK_ROUTE (CMX3_CLK_ROUTE | CMX2_CLK_ROUTE)
+
+#define CLK_TRX (PC_F3TXCLK | PC_F3RXCLK | PC_F2TXCLK | PC_F2RXCLK)
+
+/* I/O Pin assignment for FCC1.  I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PA1_COL		0x00000001U
+#define PA1_CRS		0x00000002U
+#define PA1_TXER	0x00000004U
+#define PA1_TXEN	0x00000008U
+#define PA1_RXDV	0x00000010U
+#define PA1_RXER	0x00000020U
+#define PA1_TXDAT	0x00003c00U
+#define PA1_RXDAT	0x0003c000U
+#define PA1_PSORA0	(PA1_RXDAT | PA1_TXDAT)
+#define PA1_PSORA1	(PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
+		PA1_RXDV | PA1_RXER)
+#define PA1_DIRA0	(PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
+#define PA1_DIRA1	(PA1_TXDAT | PA1_TXEN | PA1_TXER)
+
+
+/* I/O Pin assignment for FCC2.  I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB2_TXER	0x00000001U
+#define PB2_RXDV	0x00000002U
+#define PB2_TXEN	0x00000004U
+#define PB2_RXER	0x00000008U
+#define PB2_COL		0x00000010U
+#define PB2_CRS		0x00000020U
+#define PB2_TXDAT	0x000003c0U
+#define PB2_RXDAT	0x00003c00U
+#define PB2_PSORB0	(PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
+		PB2_RXER | PB2_RXDV | PB2_TXER)
+#define PB2_PSORB1	(PB2_TXEN)
+#define PB2_DIRB0	(PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
+#define PB2_DIRB1	(PB2_TXDAT | PB2_TXEN | PB2_TXER)
+
+
+/* I/O Pin assignment for FCC3.  I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB3_RXDV	0x00004000U
+#define PB3_RXER	0x00008000U
+#define PB3_TXER	0x00010000U
+#define PB3_TXEN	0x00020000U
+#define PB3_COL		0x00040000U
+#define PB3_CRS		0x00080000U
+#define PB3_TXDAT	0x0f000000U
+#define PC3_TXDAT	0x00000010U
+#define PB3_RXDAT	0x00f00000U
+#define PB3_PSORB0	(PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
+		PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
+#define PB3_PSORB1	0
+#define PB3_DIRB0	(PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
+#define PB3_DIRB1	(PB3_TXDAT | PB3_TXEN | PB3_TXER)
+#define PC3_DIRC1	(PC3_TXDAT)
+
+/* Handy macro to specify mem for FCCs*/
+#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
+#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
+#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
+#define FCC3_MEM_OFFSET FCC_MEM_OFFSET(2)
+
+/* Clocks and GRG's */
+
+enum cpm_clk_dir {
+	CPM_CLK_RX,
+	CPM_CLK_TX,
+	CPM_CLK_RTX
+};
+
+enum cpm_clk_target {
+	CPM_CLK_SCC1,
+	CPM_CLK_SCC2,
+	CPM_CLK_SCC3,
+	CPM_CLK_SCC4,
+	CPM_CLK_FCC1,
+	CPM_CLK_FCC2,
+	CPM_CLK_FCC3
+};
+
+enum cpm_clk {
+	CPM_CLK_NONE = 0,
+	CPM_BRG1,	/* Baud Rate Generator  1 */
+	CPM_BRG2,	/* Baud Rate Generator  2 */
+	CPM_BRG3,	/* Baud Rate Generator  3 */
+	CPM_BRG4,	/* Baud Rate Generator  4 */
+	CPM_BRG5,	/* Baud Rate Generator  5 */
+	CPM_BRG6,	/* Baud Rate Generator  6 */
+	CPM_BRG7,	/* Baud Rate Generator  7 */
+	CPM_BRG8,	/* Baud Rate Generator  8 */
+	CPM_CLK1,	/* Clock  1 */
+	CPM_CLK2,	/* Clock  2 */
+	CPM_CLK3,	/* Clock  3 */
+	CPM_CLK4,	/* Clock  4 */
+	CPM_CLK5,	/* Clock  5 */
+	CPM_CLK6,	/* Clock  6 */
+	CPM_CLK7,	/* Clock  7 */
+	CPM_CLK8,	/* Clock  8 */
+	CPM_CLK9,	/* Clock  9 */
+	CPM_CLK10,	/* Clock 10 */
+	CPM_CLK11,	/* Clock 11 */
+	CPM_CLK12,	/* Clock 12 */
+	CPM_CLK13,	/* Clock 13 */
+	CPM_CLK14,	/* Clock 14 */
+	CPM_CLK15,	/* Clock 15 */
+	CPM_CLK16,	/* Clock 16 */
+	CPM_CLK17,	/* Clock 17 */
+	CPM_CLK18,	/* Clock 18 */
+	CPM_CLK19,	/* Clock 19 */
+	CPM_CLK20,	/* Clock 20 */
+	CPM_CLK_DUMMY
+};
+
+extern int cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode);
+
+#endif /* __CPM2__ */
+#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/highmem.h b/include/asm-powerpc/highmem.h
new file mode 100644
index 0000000..f7b21ee
--- /dev/null
+++ b/include/asm-powerpc/highmem.h
@@ -0,0 +1,135 @@
+/*
+ * highmem.h: virtual kernel memory mappings for high memory
+ *
+ * PowerPC version, stolen from the i386 version.
+ *
+ * Used in CONFIG_HIGHMEM systems for memory pages which
+ * are not addressable by direct kernel virtual addresses.
+ *
+ * Copyright (C) 1999 Gerhard Wichert, Siemens AG
+ *		      Gerhard.Wichert@pdb.siemens.de
+ *
+ *
+ * Redesigned the x86 32-bit VM architecture to deal with
+ * up to 16 Terrabyte physical memory. With current x86 CPUs
+ * we now support up to 64 Gigabytes physical RAM.
+ *
+ * Copyright (C) 1999 Ingo Molnar <mingo@redhat.com>
+ */
+
+#ifndef _ASM_HIGHMEM_H
+#define _ASM_HIGHMEM_H
+
+#ifdef __KERNEL__
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <asm/kmap_types.h>
+#include <asm/tlbflush.h>
+#include <asm/page.h>
+
+/* undef for production */
+#define HIGHMEM_DEBUG 1
+
+extern pte_t *kmap_pte;
+extern pgprot_t kmap_prot;
+extern pte_t *pkmap_page_table;
+
+/*
+ * Right now we initialize only a single pte table. It can be extended
+ * easily, subsequent pte tables have to be allocated in one physical
+ * chunk of RAM.
+ */
+#define PKMAP_BASE 	CONFIG_HIGHMEM_START
+#define LAST_PKMAP 	(1 << PTE_SHIFT)
+#define LAST_PKMAP_MASK (LAST_PKMAP-1)
+#define PKMAP_NR(virt)  ((virt-PKMAP_BASE) >> PAGE_SHIFT)
+#define PKMAP_ADDR(nr)  (PKMAP_BASE + ((nr) << PAGE_SHIFT))
+
+#define KMAP_FIX_BEGIN	(PKMAP_BASE + 0x00400000UL)
+
+extern void *kmap_high(struct page *page);
+extern void kunmap_high(struct page *page);
+
+static inline void *kmap(struct page *page)
+{
+	might_sleep();
+	if (!PageHighMem(page))
+		return page_address(page);
+	return kmap_high(page);
+}
+
+static inline void kunmap(struct page *page)
+{
+	BUG_ON(in_interrupt());
+	if (!PageHighMem(page))
+		return;
+	kunmap_high(page);
+}
+
+/*
+ * The use of kmap_atomic/kunmap_atomic is discouraged - kmap/kunmap
+ * gives a more generic (and caching) interface. But kmap_atomic can
+ * be used in IRQ contexts, so in some (very limited) cases we need
+ * it.
+ */
+static inline void *kmap_atomic(struct page *page, enum km_type type)
+{
+	unsigned int idx;
+	unsigned long vaddr;
+
+	/* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */
+	pagefault_disable();
+	if (!PageHighMem(page))
+		return page_address(page);
+
+	idx = type + KM_TYPE_NR*smp_processor_id();
+	vaddr = KMAP_FIX_BEGIN + idx * PAGE_SIZE;
+#ifdef HIGHMEM_DEBUG
+	BUG_ON(!pte_none(*(kmap_pte+idx)));
+#endif
+	set_pte_at(&init_mm, vaddr, kmap_pte+idx, mk_pte(page, kmap_prot));
+	flush_tlb_page(NULL, vaddr);
+
+	return (void*) vaddr;
+}
+
+static inline void kunmap_atomic(void *kvaddr, enum km_type type)
+{
+#ifdef HIGHMEM_DEBUG
+	unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK;
+	unsigned int idx = type + KM_TYPE_NR*smp_processor_id();
+
+	if (vaddr < KMAP_FIX_BEGIN) { // FIXME
+		pagefault_enable();
+		return;
+	}
+
+	BUG_ON(vaddr != KMAP_FIX_BEGIN + idx * PAGE_SIZE);
+
+	/*
+	 * force other mappings to Oops if they'll try to access
+	 * this pte without first remap it
+	 */
+	pte_clear(&init_mm, vaddr, kmap_pte+idx);
+	flush_tlb_page(NULL, vaddr);
+#endif
+	pagefault_enable();
+}
+
+static inline struct page *kmap_atomic_to_page(void *ptr)
+{
+	unsigned long idx, vaddr = (unsigned long) ptr;
+
+	if (vaddr < KMAP_FIX_BEGIN)
+		return virt_to_page(ptr);
+
+	idx = (vaddr - KMAP_FIX_BEGIN) >> PAGE_SHIFT;
+	return pte_page(kmap_pte[idx]);
+}
+
+#define flush_cache_kmaps()	flush_cache_all()
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASM_HIGHMEM_H */
diff --git a/include/asm-powerpc/hydra.h b/include/asm-powerpc/hydra.h
new file mode 100644
index 0000000..1ad4eed
--- /dev/null
+++ b/include/asm-powerpc/hydra.h
@@ -0,0 +1,102 @@
+/*
+ *  include/asm-ppc/hydra.h -- Mac I/O `Hydra' definitions
+ *
+ *  Copyright (C) 1997 Geert Uytterhoeven
+ *
+ *  This file is based on the following documentation:
+ *
+ *	Macintosh Technology in the Common Hardware Reference Platform
+ *	Apple Computer, Inc.
+ *
+ *	© Copyright 1995 Apple Computer, Inc. All rights reserved.
+ *
+ *  It's available online from http://chrp.apple.com/MacTech.pdf.
+ *  You can obtain paper copies of this book from computer bookstores or by
+ *  writing Morgan Kaufmann Publishers, Inc., 340 Pine Street, Sixth Floor, San
+ *  Francisco, CA 94104. Reference ISBN 1-55860-393-X.
+ *
+ *  This file is subject to the terms and conditions of the GNU General Public
+ *  License.  See the file COPYING in the main directory of this archive
+ *  for more details.
+ */
+
+#ifndef _ASMPPC_HYDRA_H
+#define _ASMPPC_HYDRA_H
+
+#ifdef __KERNEL__
+
+struct Hydra {
+    /* DBDMA Controller Register Space */
+    char Pad1[0x30];
+    u_int CachePD;
+    u_int IDs;
+    u_int Feature_Control;
+    char Pad2[0x7fc4];
+    /* DBDMA Channel Register Space */
+    char SCSI_DMA[0x100];
+    char Pad3[0x300];
+    char SCCA_Tx_DMA[0x100];
+    char SCCA_Rx_DMA[0x100];
+    char SCCB_Tx_DMA[0x100];
+    char SCCB_Rx_DMA[0x100];
+    char Pad4[0x7800];
+    /* Device Register Space */
+    char SCSI[0x1000];
+    char ADB[0x1000];
+    char SCC_Legacy[0x1000];
+    char SCC[0x1000];
+    char Pad9[0x2000];
+    char VIA[0x2000];
+    char Pad10[0x28000];
+    char OpenPIC[0x40000];
+};
+
+extern volatile struct Hydra __iomem *Hydra;
+
+
+    /*
+     *  Feature Control Register
+     */
+
+#define HYDRA_FC_SCC_CELL_EN	0x00000001	/* Enable SCC Clock */
+#define HYDRA_FC_SCSI_CELL_EN	0x00000002	/* Enable SCSI Clock */
+#define HYDRA_FC_SCCA_ENABLE	0x00000004	/* Enable SCC A Lines */
+#define HYDRA_FC_SCCB_ENABLE	0x00000008	/* Enable SCC B Lines */
+#define HYDRA_FC_ARB_BYPASS	0x00000010	/* Bypass Internal Arbiter */
+#define HYDRA_FC_RESET_SCC	0x00000020	/* Reset SCC */
+#define HYDRA_FC_MPIC_ENABLE	0x00000040	/* Enable OpenPIC */
+#define HYDRA_FC_SLOW_SCC_PCLK	0x00000080	/* 1=15.6672, 0=25 MHz */
+#define HYDRA_FC_MPIC_IS_MASTER	0x00000100	/* OpenPIC Master Mode */
+
+
+    /*
+     *  OpenPIC Interrupt Sources
+     */
+
+#define HYDRA_INT_SIO		0
+#define HYDRA_INT_SCSI_DMA	1
+#define HYDRA_INT_SCCA_TX_DMA	2
+#define HYDRA_INT_SCCA_RX_DMA	3
+#define HYDRA_INT_SCCB_TX_DMA	4
+#define HYDRA_INT_SCCB_RX_DMA	5
+#define HYDRA_INT_SCSI		6
+#define HYDRA_INT_SCCA		7
+#define HYDRA_INT_SCCB		8
+#define HYDRA_INT_VIA		9
+#define HYDRA_INT_ADB		10
+#define HYDRA_INT_ADB_NMI	11
+#define HYDRA_INT_EXT1		12	/* PCI IRQW */
+#define HYDRA_INT_EXT2		13	/* PCI IRQX */
+#define HYDRA_INT_EXT3		14	/* PCI IRQY */
+#define HYDRA_INT_EXT4		15	/* PCI IRQZ */
+#define HYDRA_INT_EXT5		16	/* IDE Primay/Secondary */
+#define HYDRA_INT_EXT6		17	/* IDE Secondary */
+#define HYDRA_INT_EXT7		18	/* Power Off Request */
+#define HYDRA_INT_SPARE		19
+
+extern int hydra_init(void);
+extern void macio_adb_init(void);
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASMPPC_HYDRA_H */
diff --git a/include/asm-powerpc/immap_cpm2.h b/include/asm-powerpc/immap_cpm2.h
new file mode 100644
index 0000000..f316a91
--- /dev/null
+++ b/include/asm-powerpc/immap_cpm2.h
@@ -0,0 +1,648 @@
+/*
+ * CPM2 Internal Memory Map
+ * Copyright (c) 1999 Dan Malek (dmalek@jlc.net)
+ *
+ * The Internal Memory Map for devices with CPM2 on them.  This
+ * is the superset of all CPM2 devices (8260, 8266, 8280, 8272,
+ * 8560).
+ */
+#ifdef __KERNEL__
+#ifndef __IMMAP_CPM2__
+#define __IMMAP_CPM2__
+
+/* System configuration registers.
+*/
+typedef	struct sys_82xx_conf {
+	u32	sc_siumcr;
+	u32	sc_sypcr;
+	u8	res1[6];
+	u16	sc_swsr;
+	u8	res2[20];
+	u32	sc_bcr;
+	u8	sc_ppc_acr;
+	u8	res3[3];
+	u32	sc_ppc_alrh;
+	u32	sc_ppc_alrl;
+	u8	sc_lcl_acr;
+	u8	res4[3];
+	u32	sc_lcl_alrh;
+	u32	sc_lcl_alrl;
+	u32	sc_tescr1;
+	u32	sc_tescr2;
+	u32	sc_ltescr1;
+	u32	sc_ltescr2;
+	u32	sc_pdtea;
+	u8	sc_pdtem;
+	u8	res5[3];
+	u32	sc_ldtea;
+	u8	sc_ldtem;
+	u8	res6[163];
+} sysconf_82xx_cpm2_t;
+
+typedef	struct sys_85xx_conf {
+	u32	sc_cear;
+	u16	sc_ceer;
+	u16	sc_cemr;
+	u8	res1[70];
+	u32	sc_smaer;
+	u8	res2[4];
+	u32	sc_smevr;
+	u32	sc_smctr;
+	u32	sc_lmaer;
+	u8	res3[4];
+	u32	sc_lmevr;
+	u32	sc_lmctr;
+	u8	res4[144];
+} sysconf_85xx_cpm2_t;
+
+typedef union sys_conf {
+	sysconf_82xx_cpm2_t	siu_82xx;
+	sysconf_85xx_cpm2_t	siu_85xx;
+} sysconf_cpm2_t;
+
+
+
+/* Memory controller registers.
+*/
+typedef struct	mem_ctlr {
+	u32	memc_br0;
+	u32	memc_or0;
+	u32	memc_br1;
+	u32	memc_or1;
+	u32	memc_br2;
+	u32	memc_or2;
+	u32	memc_br3;
+	u32	memc_or3;
+	u32	memc_br4;
+	u32	memc_or4;
+	u32	memc_br5;
+	u32	memc_or5;
+	u32	memc_br6;
+	u32	memc_or6;
+	u32	memc_br7;
+	u32	memc_or7;
+	u32	memc_br8;
+	u32	memc_or8;
+	u32	memc_br9;
+	u32	memc_or9;
+	u32	memc_br10;
+	u32	memc_or10;
+	u32	memc_br11;
+	u32	memc_or11;
+	u8	res1[8];
+	u32	memc_mar;
+	u8	res2[4];
+	u32	memc_mamr;
+	u32	memc_mbmr;
+	u32	memc_mcmr;
+	u8	res3[8];
+	u16	memc_mptpr;
+	u8	res4[2];
+	u32	memc_mdr;
+	u8	res5[4];
+	u32	memc_psdmr;
+	u32	memc_lsdmr;
+	u8	memc_purt;
+	u8	res6[3];
+	u8	memc_psrt;
+	u8	res7[3];
+	u8	memc_lurt;
+	u8	res8[3];
+	u8	memc_lsrt;
+	u8	res9[3];
+	u32	memc_immr;
+	u32	memc_pcibr0;
+	u32	memc_pcibr1;
+	u8	res10[16];
+	u32	memc_pcimsk0;
+	u32	memc_pcimsk1;
+	u8	res11[52];
+} memctl_cpm2_t;
+
+/* System Integration Timers.
+*/
+typedef struct	sys_int_timers {
+	u8	res1[32];
+	u16	sit_tmcntsc;
+	u8	res2[2];
+	u32	sit_tmcnt;
+	u8	res3[4];
+	u32	sit_tmcntal;
+	u8	res4[16];
+	u16	sit_piscr;
+	u8	res5[2];
+	u32	sit_pitc;
+	u32	sit_pitr;
+	u8      res6[94];
+	u8	res7[390];
+} sit_cpm2_t;
+
+#define PISCR_PIRQ_MASK		((u16)0xff00)
+#define PISCR_PS		((u16)0x0080)
+#define PISCR_PIE		((u16)0x0004)
+#define PISCR_PTF		((u16)0x0002)
+#define PISCR_PTE		((u16)0x0001)
+
+/* PCI Controller.
+*/
+typedef struct pci_ctlr {
+	u32	pci_omisr;
+	u32	pci_omimr;
+	u8	res1[8];
+	u32	pci_ifqpr;
+	u32	pci_ofqpr;
+	u8	res2[8];
+	u32	pci_imr0;
+	u32	pci_imr1;
+	u32	pci_omr0;
+	u32	pci_omr1;
+	u32	pci_odr;
+	u8	res3[4];
+	u32	pci_idr;
+	u8	res4[20];
+	u32	pci_imisr;
+	u32	pci_imimr;
+	u8	res5[24];
+	u32	pci_ifhpr;
+	u8	res6[4];
+	u32	pci_iftpr;
+	u8	res7[4];
+	u32	pci_iphpr;
+	u8	res8[4];
+	u32	pci_iptpr;
+	u8	res9[4];
+	u32	pci_ofhpr;
+	u8	res10[4];
+	u32	pci_oftpr;
+	u8	res11[4];
+	u32	pci_ophpr;
+	u8	res12[4];
+	u32	pci_optpr;
+	u8	res13[8];
+	u32	pci_mucr;
+	u8	res14[8];
+	u32	pci_qbar;
+	u8	res15[12];
+	u32	pci_dmamr0;
+	u32	pci_dmasr0;
+	u32	pci_dmacdar0;
+	u8	res16[4];
+	u32	pci_dmasar0;
+	u8	res17[4];
+	u32	pci_dmadar0;
+	u8	res18[4];
+	u32	pci_dmabcr0;
+	u32	pci_dmandar0;
+	u8	res19[86];
+	u32	pci_dmamr1;
+	u32	pci_dmasr1;
+	u32	pci_dmacdar1;
+	u8	res20[4];
+	u32	pci_dmasar1;
+	u8	res21[4];
+	u32	pci_dmadar1;
+	u8	res22[4];
+	u32	pci_dmabcr1;
+	u32	pci_dmandar1;
+	u8	res23[88];
+	u32	pci_dmamr2;
+	u32	pci_dmasr2;
+	u32	pci_dmacdar2;
+	u8	res24[4];
+	u32	pci_dmasar2;
+	u8	res25[4];
+	u32	pci_dmadar2;
+	u8	res26[4];
+	u32	pci_dmabcr2;
+	u32	pci_dmandar2;
+	u8	res27[88];
+	u32	pci_dmamr3;
+	u32	pci_dmasr3;
+	u32	pci_dmacdar3;
+	u8	res28[4];
+	u32	pci_dmasar3;
+	u8	res29[4];
+	u32	pci_dmadar3;
+	u8	res30[4];
+	u32	pci_dmabcr3;
+	u32	pci_dmandar3;
+	u8	res31[344];
+	u32	pci_potar0;
+	u8	res32[4];
+	u32	pci_pobar0;
+	u8	res33[4];
+	u32	pci_pocmr0;
+	u8	res34[4];
+	u32	pci_potar1;
+	u8	res35[4];
+	u32	pci_pobar1;
+	u8	res36[4];
+	u32	pci_pocmr1;
+	u8	res37[4];
+	u32	pci_potar2;
+	u8	res38[4];
+	u32	pci_pobar2;
+	u8	res39[4];
+	u32	pci_pocmr2;
+	u8	res40[50];
+	u32	pci_ptcr;
+	u32	pci_gpcr;
+	u32	pci_gcr;
+	u32	pci_esr;
+	u32	pci_emr;
+	u32	pci_ecr;
+	u32	pci_eacr;
+	u8	res41[4];
+	u32	pci_edcr;
+	u8	res42[4];
+	u32	pci_eccr;
+	u8	res43[44];
+	u32	pci_pitar1;
+	u8	res44[4];
+	u32	pci_pibar1;
+	u8	res45[4];
+	u32	pci_picmr1;
+	u8	res46[4];
+	u32	pci_pitar0;
+	u8	res47[4];
+	u32	pci_pibar0;
+	u8	res48[4];
+	u32	pci_picmr0;
+	u8	res49[4];
+	u32	pci_cfg_addr;
+	u32	pci_cfg_data;
+	u32	pci_int_ack;
+	u8	res50[756];
+} pci_cpm2_t;
+
+/* Interrupt Controller.
+*/
+typedef struct interrupt_controller {
+	u16	ic_sicr;
+	u8	res1[2];
+	u32	ic_sivec;
+	u32	ic_sipnrh;
+	u32	ic_sipnrl;
+	u32	ic_siprr;
+	u32	ic_scprrh;
+	u32	ic_scprrl;
+	u32	ic_simrh;
+	u32	ic_simrl;
+	u32	ic_siexr;
+	u8	res2[88];
+} intctl_cpm2_t;
+
+/* Clocks and Reset.
+*/
+typedef struct clk_and_reset {
+	u32	car_sccr;
+	u8	res1[4];
+	u32	car_scmr;
+	u8	res2[4];
+	u32	car_rsr;
+	u32	car_rmr;
+	u8	res[104];
+} car_cpm2_t;
+
+/* Input/Output Port control/status registers.
+ * Names consistent with processor manual, although they are different
+ * from the original 8xx names.......
+ */
+typedef struct io_port {
+	u32	iop_pdira;
+	u32	iop_ppara;
+	u32	iop_psora;
+	u32	iop_podra;
+	u32	iop_pdata;
+	u8	res1[12];
+	u32	iop_pdirb;
+	u32	iop_pparb;
+	u32	iop_psorb;
+	u32	iop_podrb;
+	u32	iop_pdatb;
+	u8	res2[12];
+	u32	iop_pdirc;
+	u32	iop_pparc;
+	u32	iop_psorc;
+	u32	iop_podrc;
+	u32	iop_pdatc;
+	u8	res3[12];
+	u32	iop_pdird;
+	u32	iop_ppard;
+	u32	iop_psord;
+	u32	iop_podrd;
+	u32	iop_pdatd;
+	u8	res4[12];
+} iop_cpm2_t;
+
+/* Communication Processor Module Timers
+*/
+typedef struct cpm_timers {
+	u8	cpmt_tgcr1;
+	u8	res1[3];
+	u8	cpmt_tgcr2;
+	u8	res2[11];
+	u16	cpmt_tmr1;
+	u16	cpmt_tmr2;
+	u16	cpmt_trr1;
+	u16	cpmt_trr2;
+	u16	cpmt_tcr1;
+	u16	cpmt_tcr2;
+	u16	cpmt_tcn1;
+	u16	cpmt_tcn2;
+	u16	cpmt_tmr3;
+	u16	cpmt_tmr4;
+	u16	cpmt_trr3;
+	u16	cpmt_trr4;
+	u16	cpmt_tcr3;
+	u16	cpmt_tcr4;
+	u16	cpmt_tcn3;
+	u16	cpmt_tcn4;
+	u16	cpmt_ter1;
+	u16	cpmt_ter2;
+	u16	cpmt_ter3;
+	u16	cpmt_ter4;
+	u8	res3[584];
+} cpmtimer_cpm2_t;
+
+/* DMA control/status registers.
+*/
+typedef struct sdma_csr {
+	u8	res0[24];
+	u8	sdma_sdsr;
+	u8	res1[3];
+	u8	sdma_sdmr;
+	u8	res2[3];
+	u8	sdma_idsr1;
+	u8	res3[3];
+	u8	sdma_idmr1;
+	u8	res4[3];
+	u8	sdma_idsr2;
+	u8	res5[3];
+	u8	sdma_idmr2;
+	u8	res6[3];
+	u8	sdma_idsr3;
+	u8	res7[3];
+	u8	sdma_idmr3;
+	u8	res8[3];
+	u8	sdma_idsr4;
+	u8	res9[3];
+	u8	sdma_idmr4;
+	u8	res10[707];
+} sdma_cpm2_t;
+
+/* Fast controllers
+*/
+typedef struct fcc {
+	u32	fcc_gfmr;
+	u32	fcc_fpsmr;
+	u16	fcc_ftodr;
+	u8	res1[2];
+	u16	fcc_fdsr;
+	u8	res2[2];
+	u16	fcc_fcce;
+	u8	res3[2];
+	u16	fcc_fccm;
+	u8	res4[2];
+	u8	fcc_fccs;
+	u8	res5[3];
+	u8	fcc_ftirr_phy[4];
+} fcc_t;
+
+/* Fast controllers continued
+ */
+typedef struct fcc_c {
+	u32	fcc_firper;
+	u32	fcc_firer;
+	u32	fcc_firsr_hi;
+	u32	fcc_firsr_lo;
+	u8	fcc_gfemr;
+	u8	res1[15];
+} fcc_c_t;
+
+/* TC Layer
+ */
+typedef struct tclayer {
+	u16	tc_tcmode;
+	u16	tc_cdsmr;
+	u16	tc_tcer;
+	u16	tc_rcc;
+	u16	tc_tcmr;
+	u16	tc_fcc;
+	u16	tc_ccc;
+	u16	tc_icc;
+	u16	tc_tcc;
+	u16	tc_ecc;
+	u8	res1[12];
+} tclayer_t;
+
+
+/* I2C
+*/
+typedef struct i2c {
+	u8	i2c_i2mod;
+	u8	res1[3];
+	u8	i2c_i2add;
+	u8	res2[3];
+	u8	i2c_i2brg;
+	u8	res3[3];
+	u8	i2c_i2com;
+	u8	res4[3];
+	u8	i2c_i2cer;
+	u8	res5[3];
+	u8	i2c_i2cmr;
+	u8	res6[331];
+} i2c_cpm2_t;
+
+typedef struct scc {		/* Serial communication channels */
+	u32	scc_gsmrl;
+	u32	scc_gsmrh;
+	u16	scc_psmr;
+	u8	res1[2];
+	u16	scc_todr;
+	u16	scc_dsr;
+	u16	scc_scce;
+	u8	res2[2];
+	u16	scc_sccm;
+	u8	res3;
+	u8	scc_sccs;
+	u8	res4[8];
+} scc_t;
+
+typedef struct smc {		/* Serial management channels */
+	u8	res1[2];
+	u16	smc_smcmr;
+	u8	res2[2];
+	u8	smc_smce;
+	u8	res3[3];
+	u8	smc_smcm;
+	u8	res4[5];
+} smc_t;
+
+/* Serial Peripheral Interface.
+*/
+typedef struct spi_ctrl {
+	u16	spi_spmode;
+	u8	res1[4];
+	u8	spi_spie;
+	u8	res2[3];
+	u8	spi_spim;
+	u8	res3[2];
+	u8	spi_spcom;
+	u8	res4[82];
+} spictl_cpm2_t;
+
+/* CPM Mux.
+*/
+typedef struct cpmux {
+	u8	cmx_si1cr;
+	u8	res1;
+	u8	cmx_si2cr;
+	u8	res2;
+	u32	cmx_fcr;
+	u32	cmx_scr;
+	u8	cmx_smr;
+	u8	res3;
+	u16	cmx_uar;
+	u8	res4[16];
+} cpmux_t;
+
+/* SIRAM control
+*/
+typedef struct siram {
+	u16	si_amr;
+	u16	si_bmr;
+	u16	si_cmr;
+	u16	si_dmr;
+	u8	si_gmr;
+	u8	res1;
+	u8	si_cmdr;
+	u8	res2;
+	u8	si_str;
+	u8	res3;
+	u16	si_rsr;
+} siramctl_t;
+
+typedef struct mcc {
+	u16	mcc_mcce;
+	u8	res1[2];
+	u16	mcc_mccm;
+	u8	res2[2];
+	u8	mcc_mccf;
+	u8	res3[7];
+} mcc_t;
+
+typedef struct comm_proc {
+	u32	cp_cpcr;
+	u32	cp_rccr;
+	u8	res1[14];
+	u16	cp_rter;
+	u8	res2[2];
+	u16	cp_rtmr;
+	u16	cp_rtscr;
+	u8	res3[2];
+	u32	cp_rtsr;
+	u8	res4[12];
+} cpm_cpm2_t;
+
+/* USB Controller.
+*/
+typedef struct usb_ctlr {
+	u8	usb_usmod;
+	u8	usb_usadr;
+	u8	usb_uscom;
+	u8	res1[1];
+	u16	usb_usep1;
+	u16	usb_usep2;
+	u16	usb_usep3;
+	u16	usb_usep4;
+	u8	res2[4];
+	u16	usb_usber;
+	u8	res3[2];
+	u16	usb_usbmr;
+	u8	usb_usbs;
+	u8	res4[7];
+} usb_cpm2_t;
+
+/* ...and the whole thing wrapped up....
+*/
+
+typedef struct immap {
+	/* Some references are into the unique and known dpram spaces,
+	 * others are from the generic base.
+	 */
+#define im_dprambase	im_dpram1
+	u8		im_dpram1[16*1024];
+	u8		res1[16*1024];
+	u8		im_dpram2[4*1024];
+	u8		res2[8*1024];
+	u8		im_dpram3[4*1024];
+	u8		res3[16*1024];
+
+	sysconf_cpm2_t	im_siu_conf;	/* SIU Configuration */
+	memctl_cpm2_t	im_memctl;	/* Memory Controller */
+	sit_cpm2_t	im_sit;		/* System Integration Timers */
+	pci_cpm2_t	im_pci;		/* PCI Controller */
+	intctl_cpm2_t	im_intctl;	/* Interrupt Controller */
+	car_cpm2_t	im_clkrst;	/* Clocks and reset */
+	iop_cpm2_t	im_ioport;	/* IO Port control/status */
+	cpmtimer_cpm2_t	im_cpmtimer;	/* CPM timers */
+	sdma_cpm2_t	im_sdma;	/* SDMA control/status */
+
+	fcc_t		im_fcc[3];	/* Three FCCs */
+	u8		res4z[32];
+	fcc_c_t		im_fcc_c[3];	/* Continued FCCs */
+
+	u8		res4[32];
+
+	tclayer_t	im_tclayer[8];	/* Eight TCLayers */
+	u16		tc_tcgsr;
+	u16		tc_tcger;
+
+	/* First set of baud rate generators.
+	*/
+	u8		res[236];
+	u32		im_brgc5;
+	u32		im_brgc6;
+	u32		im_brgc7;
+	u32		im_brgc8;
+
+	u8		res5[608];
+
+	i2c_cpm2_t	im_i2c;		/* I2C control/status */
+	cpm_cpm2_t	im_cpm;		/* Communication processor */
+
+	/* Second set of baud rate generators.
+	*/
+	u32		im_brgc1;
+	u32		im_brgc2;
+	u32		im_brgc3;
+	u32		im_brgc4;
+
+	scc_t		im_scc[4];	/* Four SCCs */
+	smc_t		im_smc[2];	/* Couple of SMCs */
+	spictl_cpm2_t	im_spi;		/* A SPI */
+	cpmux_t		im_cpmux;	/* CPM clock route mux */
+	siramctl_t	im_siramctl1;	/* First SI RAM Control */
+	mcc_t		im_mcc1;	/* First MCC */
+	siramctl_t	im_siramctl2;	/* Second SI RAM Control */
+	mcc_t		im_mcc2;	/* Second MCC */
+	usb_cpm2_t	im_usb;		/* USB Controller */
+
+	u8		res6[1153];
+
+	u16		im_si1txram[256];
+	u8		res7[512];
+	u16		im_si1rxram[256];
+	u8		res8[512];
+	u16		im_si2txram[256];
+	u8		res9[512];
+	u16		im_si2rxram[256];
+	u8		res10[512];
+	u8		res11[4096];
+} cpm2_map_t;
+
+extern cpm2_map_t	*cpm2_immr;
+
+#endif /* __IMMAP_CPM2__ */
+#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/kgdb.h b/include/asm-powerpc/kgdb.h
new file mode 100644
index 0000000..b617dac
--- /dev/null
+++ b/include/asm-powerpc/kgdb.h
@@ -0,0 +1,57 @@
+/*
+ * kgdb.h: Defines and declarations for serial line source level
+ *         remote debugging of the Linux kernel using gdb.
+ *
+ * PPC Mods (C) 1998 Michael Tesch (tesch@cs.wisc.edu)
+ *
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ */
+#ifdef __KERNEL__
+#ifndef _PPC_KGDB_H
+#define _PPC_KGDB_H
+
+#ifndef __ASSEMBLY__
+
+/* Things specific to the gen550 backend. */
+struct uart_port;
+
+extern void gen550_progress(char *, unsigned short);
+extern void gen550_kgdb_map_scc(void);
+extern void gen550_init(int, struct uart_port *);
+
+/* Things specific to the pmac backend. */
+extern void zs_kgdb_hook(int tty_num);
+
+/* To init the kgdb engine. (called by serial hook)*/
+extern void set_debug_traps(void);
+
+/* To enter the debugger explicitly. */
+extern void breakpoint(void);
+
+/* For taking exceptions
+ * these are defined in traps.c
+ */
+extern int (*debugger)(struct pt_regs *regs);
+extern int (*debugger_bpt)(struct pt_regs *regs);
+extern int (*debugger_sstep)(struct pt_regs *regs);
+extern int (*debugger_iabr_match)(struct pt_regs *regs);
+extern int (*debugger_dabr_match)(struct pt_regs *regs);
+extern void (*debugger_fault_handler)(struct pt_regs *regs);
+
+/* What we bring to the party */
+int kgdb_bpt(struct pt_regs *regs);
+int kgdb_sstep(struct pt_regs *regs);
+void kgdb(struct pt_regs *regs);
+int kgdb_iabr_match(struct pt_regs *regs);
+int kgdb_dabr_match(struct pt_regs *regs);
+
+/*
+ * external low-level support routines (ie macserial.c)
+ */
+extern void kgdb_interruptible(int); /* control interrupts from serial */
+extern void putDebugChar(char);   /* write a single character      */
+extern char getDebugChar(void);   /* read and return a single char */
+
+#endif /* !(__ASSEMBLY__) */
+#endif /* !(_PPC_KGDB_H) */
+#endif /* __KERNEL__ */
diff --git a/include/asm-powerpc/mpc52xx_psc.h b/include/asm-powerpc/mpc52xx_psc.h
new file mode 100644
index 0000000..26690d2
--- /dev/null
+++ b/include/asm-powerpc/mpc52xx_psc.h
@@ -0,0 +1,191 @@
+/*
+ * include/asm-ppc/mpc52xx_psc.h
+ *
+ * Definitions of consts/structs to drive the Freescale MPC52xx OnChip
+ * PSCs. Theses are shared between multiple drivers since a PSC can be
+ * UART, AC97, IR, I2S, ... So this header is in asm-ppc.
+ *
+ *
+ * Maintainer : Sylvain Munaut <tnt@246tNt.com>
+ *
+ * Based/Extracted from some header of the 2.4 originally written by
+ * Dale Farnsworth <dfarnsworth@mvista.com>
+ *
+ * Copyright (C) 2004 Sylvain Munaut <tnt@246tNt.com>
+ * Copyright (C) 2003 MontaVista, Software, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef __ASM_MPC52xx_PSC_H__
+#define __ASM_MPC52xx_PSC_H__
+
+#include <asm/types.h>
+
+/* Max number of PSCs */
+#define MPC52xx_PSC_MAXNUM	6
+
+/* Programmable Serial Controller (PSC) status register bits */
+#define MPC52xx_PSC_SR_CDE	0x0080
+#define MPC52xx_PSC_SR_RXRDY	0x0100
+#define MPC52xx_PSC_SR_RXFULL	0x0200
+#define MPC52xx_PSC_SR_TXRDY	0x0400
+#define MPC52xx_PSC_SR_TXEMP	0x0800
+#define MPC52xx_PSC_SR_OE	0x1000
+#define MPC52xx_PSC_SR_PE	0x2000
+#define MPC52xx_PSC_SR_FE	0x4000
+#define MPC52xx_PSC_SR_RB	0x8000
+
+/* PSC Command values */
+#define MPC52xx_PSC_RX_ENABLE		0x0001
+#define MPC52xx_PSC_RX_DISABLE		0x0002
+#define MPC52xx_PSC_TX_ENABLE		0x0004
+#define MPC52xx_PSC_TX_DISABLE		0x0008
+#define MPC52xx_PSC_SEL_MODE_REG_1	0x0010
+#define MPC52xx_PSC_RST_RX		0x0020
+#define MPC52xx_PSC_RST_TX		0x0030
+#define MPC52xx_PSC_RST_ERR_STAT	0x0040
+#define MPC52xx_PSC_RST_BRK_CHG_INT	0x0050
+#define MPC52xx_PSC_START_BRK		0x0060
+#define MPC52xx_PSC_STOP_BRK		0x0070
+
+/* PSC TxRx FIFO status bits */
+#define MPC52xx_PSC_RXTX_FIFO_ERR	0x0040
+#define MPC52xx_PSC_RXTX_FIFO_UF	0x0020
+#define MPC52xx_PSC_RXTX_FIFO_OF	0x0010
+#define MPC52xx_PSC_RXTX_FIFO_FR	0x0008
+#define MPC52xx_PSC_RXTX_FIFO_FULL	0x0004
+#define MPC52xx_PSC_RXTX_FIFO_ALARM	0x0002
+#define MPC52xx_PSC_RXTX_FIFO_EMPTY	0x0001
+
+/* PSC interrupt mask bits */
+#define MPC52xx_PSC_IMR_TXRDY		0x0100
+#define MPC52xx_PSC_IMR_RXRDY		0x0200
+#define MPC52xx_PSC_IMR_DB		0x0400
+#define MPC52xx_PSC_IMR_IPC		0x8000
+
+/* PSC input port change bit */
+#define MPC52xx_PSC_CTS			0x01
+#define MPC52xx_PSC_DCD			0x02
+#define MPC52xx_PSC_D_CTS		0x10
+#define MPC52xx_PSC_D_DCD		0x20
+
+/* PSC mode fields */
+#define MPC52xx_PSC_MODE_5_BITS			0x00
+#define MPC52xx_PSC_MODE_6_BITS			0x01
+#define MPC52xx_PSC_MODE_7_BITS			0x02
+#define MPC52xx_PSC_MODE_8_BITS			0x03
+#define MPC52xx_PSC_MODE_BITS_MASK		0x03
+#define MPC52xx_PSC_MODE_PAREVEN		0x00
+#define MPC52xx_PSC_MODE_PARODD			0x04
+#define MPC52xx_PSC_MODE_PARFORCE		0x08
+#define MPC52xx_PSC_MODE_PARNONE		0x10
+#define MPC52xx_PSC_MODE_ERR			0x20
+#define MPC52xx_PSC_MODE_FFULL			0x40
+#define MPC52xx_PSC_MODE_RXRTS			0x80
+
+#define MPC52xx_PSC_MODE_ONE_STOP_5_BITS	0x00
+#define MPC52xx_PSC_MODE_ONE_STOP		0x07
+#define MPC52xx_PSC_MODE_TWO_STOP		0x0f
+
+#define MPC52xx_PSC_RFNUM_MASK	0x01ff
+
+
+/* Structure of the hardware registers */
+struct mpc52xx_psc {
+	u8		mode;		/* PSC + 0x00 */
+	u8		reserved0[3];
+	union {				/* PSC + 0x04 */
+		u16	status;
+		u16	clock_select;
+	} sr_csr;
+#define mpc52xx_psc_status	sr_csr.status
+#define mpc52xx_psc_clock_select sr_csr.clock_select
+	u16		reserved1;
+	u8		command;	/* PSC + 0x08 */
+	u8		reserved2[3];
+	union {				/* PSC + 0x0c */
+		u8	buffer_8;
+		u16	buffer_16;
+		u32	buffer_32;
+	} buffer;
+#define mpc52xx_psc_buffer_8	buffer.buffer_8
+#define mpc52xx_psc_buffer_16	buffer.buffer_16
+#define mpc52xx_psc_buffer_32	buffer.buffer_32
+	union {				/* PSC + 0x10 */
+		u8	ipcr;
+		u8	acr;
+	} ipcr_acr;
+#define mpc52xx_psc_ipcr	ipcr_acr.ipcr
+#define mpc52xx_psc_acr		ipcr_acr.acr
+	u8		reserved3[3];
+	union {				/* PSC + 0x14 */
+		u16	isr;
+		u16	imr;
+	} isr_imr;
+#define mpc52xx_psc_isr		isr_imr.isr
+#define mpc52xx_psc_imr		isr_imr.imr
+	u16		reserved4;
+	u8		ctur;		/* PSC + 0x18 */
+	u8		reserved5[3];
+	u8		ctlr;		/* PSC + 0x1c */
+	u8		reserved6[3];
+	u16		ccr;		/* PSC + 0x20 */
+	u8		reserved7[14];
+	u8		ivr;		/* PSC + 0x30 */
+	u8		reserved8[3];
+	u8		ip;		/* PSC + 0x34 */
+	u8		reserved9[3];
+	u8		op1;		/* PSC + 0x38 */
+	u8		reserved10[3];
+	u8		op0;		/* PSC + 0x3c */
+	u8		reserved11[3];
+	u32		sicr;		/* PSC + 0x40 */
+	u8		ircr1;		/* PSC + 0x44 */
+	u8		reserved13[3];
+	u8		ircr2;		/* PSC + 0x44 */
+	u8		reserved14[3];
+	u8		irsdr;		/* PSC + 0x4c */
+	u8		reserved15[3];
+	u8		irmdr;		/* PSC + 0x50 */
+	u8		reserved16[3];
+	u8		irfdr;		/* PSC + 0x54 */
+	u8		reserved17[3];
+	u16		rfnum;		/* PSC + 0x58 */
+	u16		reserved18;
+	u16		tfnum;		/* PSC + 0x5c */
+	u16		reserved19;
+	u32		rfdata;		/* PSC + 0x60 */
+	u16		rfstat;		/* PSC + 0x64 */
+	u16		reserved20;
+	u8		rfcntl;		/* PSC + 0x68 */
+	u8		reserved21[5];
+	u16		rfalarm;	/* PSC + 0x6e */
+	u16		reserved22;
+	u16		rfrptr;		/* PSC + 0x72 */
+	u16		reserved23;
+	u16		rfwptr;		/* PSC + 0x76 */
+	u16		reserved24;
+	u16		rflrfptr;	/* PSC + 0x7a */
+	u16		reserved25;
+	u16		rflwfptr;	/* PSC + 0x7e */
+	u32		tfdata;		/* PSC + 0x80 */
+	u16		tfstat;		/* PSC + 0x84 */
+	u16		reserved26;
+	u8		tfcntl;		/* PSC + 0x88 */
+	u8		reserved27[5];
+	u16		tfalarm;	/* PSC + 0x8e */
+	u16		reserved28;
+	u16		tfrptr;		/* PSC + 0x92 */
+	u16		reserved29;
+	u16		tfwptr;		/* PSC + 0x96 */
+	u16		reserved30;
+	u16		tflrfptr;	/* PSC + 0x9a */
+	u16		reserved31;
+	u16		tflwfptr;	/* PSC + 0x9e */
+};
+
+
+#endif  /* __ASM_MPC52xx_PSC_H__ */