diff --git a/Documentation/devicetree/bindings/i2c/i2c-opal.txt b/Documentation/devicetree/bindings/i2c/i2c-opal.txt
new file mode 100644
index 0000000..12bc614
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-opal.txt
@@ -0,0 +1,37 @@
+Device-tree bindings for I2C OPAL driver
+----------------------------------------
+
+Most of the device node and properties layout is specific to the firmware and
+used by the firmware itself for configuring the port. From the linux
+perspective, the properties of use are "ibm,port-name" and "ibm,opal-id".
+
+Required properties:
+
+- reg: Port-id within a given master
+- compatible: must be "ibm,opal-i2c"
+- ibm,opal-id: Refers to a specific bus and used to identify it when calling
+	       the relevant OPAL functions.
+- bus-frequency: Operating frequency of the i2c bus (in HZ). Informational for
+		 linux, used by the FW though.
+
+Optional properties:
+- ibm,port-name: Firmware provides this name that uniquely identifies the i2c
+		 port.
+
+The node contains a number of other properties that are used by the FW itself
+and depend on the specific hardware implementation. The example below depicts
+a P8 on-chip bus.
+
+Example:
+
+i2c-bus@0 {
+	reg = <0x0>;
+	bus-frequency = <0x61a80>;
+	compatible = "ibm,power8-i2c-port", "ibm,opal-i2c";
+	ibm,opal-id = <0x1>;
+	ibm,port-name = "p8_00000000_e1p0";
+	#address-cells = <0x1>;
+	phandle = <0x10000006>;
+	#size-cells = <0x0>;
+	linux,phandle = <0x10000006>;
+};
diff --git a/arch/powerpc/include/asm/cpuidle.h b/arch/powerpc/include/asm/cpuidle.h
new file mode 100644
index 0000000..d2f99ca
--- /dev/null
+++ b/arch/powerpc/include/asm/cpuidle.h
@@ -0,0 +1,20 @@
+#ifndef _ASM_POWERPC_CPUIDLE_H
+#define _ASM_POWERPC_CPUIDLE_H
+
+#ifdef CONFIG_PPC_POWERNV
+/* Used in powernv idle state management */
+#define PNV_THREAD_RUNNING              0
+#define PNV_THREAD_NAP                  1
+#define PNV_THREAD_SLEEP                2
+#define PNV_THREAD_WINKLE               3
+#define PNV_CORE_IDLE_LOCK_BIT          0x100
+#define PNV_CORE_IDLE_THREAD_BITS       0x0FF
+
+#ifndef __ASSEMBLY__
+extern u32 pnv_fastsleep_workaround_at_entry[];
+extern u32 pnv_fastsleep_workaround_at_exit[];
+#endif
+
+#endif
+
+#endif
diff --git a/arch/powerpc/include/asm/opal.h b/arch/powerpc/include/asm/opal.h
index 5cd8d2f..eb95b67 100644
--- a/arch/powerpc/include/asm/opal.h
+++ b/arch/powerpc/include/asm/opal.h
@@ -56,6 +56,14 @@
 #define OPAL_HARDWARE_FROZEN	-13
 #define OPAL_WRONG_STATE	-14
 #define OPAL_ASYNC_COMPLETION	-15
+#define OPAL_I2C_TIMEOUT	-17
+#define OPAL_I2C_INVALID_CMD	-18
+#define OPAL_I2C_LBUS_PARITY	-19
+#define OPAL_I2C_BKEND_OVERRUN	-20
+#define OPAL_I2C_BKEND_ACCESS	-21
+#define OPAL_I2C_ARBT_LOST	-22
+#define OPAL_I2C_NACK_RCVD	-23
+#define OPAL_I2C_STOP_ERR	-24
 
 /* API Tokens (in r0) */
 #define OPAL_INVALID_CALL			-1
@@ -152,12 +160,25 @@
 #define OPAL_PCI_ERR_INJECT			96
 #define OPAL_PCI_EEH_FREEZE_SET			97
 #define OPAL_HANDLE_HMI				98
+#define OPAL_CONFIG_CPU_IDLE_STATE		99
+#define OPAL_SLW_SET_REG			100
 #define OPAL_REGISTER_DUMP_REGION		101
 #define OPAL_UNREGISTER_DUMP_REGION		102
 #define OPAL_WRITE_TPO				103
 #define OPAL_READ_TPO				104
 #define OPAL_IPMI_SEND				107
 #define OPAL_IPMI_RECV				108
+#define OPAL_I2C_REQUEST			109
+
+/* Device tree flags */
+
+/* Flags set in power-mgmt nodes in device tree if
+ * respective idle states are supported in the platform.
+ */
+#define OPAL_PM_NAP_ENABLED	0x00010000
+#define OPAL_PM_SLEEP_ENABLED	0x00020000
+#define OPAL_PM_WINKLE_ENABLED	0x00040000
+#define OPAL_PM_SLEEP_ENABLED_ER1	0x00080000
 
 #ifndef __ASSEMBLY__
 
@@ -712,6 +733,24 @@
 	uint64_t 	line_len;
 } oppanel_line_t;
 
+/* OPAL I2C request */
+struct opal_i2c_request {
+	uint8_t	type;
+#define OPAL_I2C_RAW_READ	0
+#define OPAL_I2C_RAW_WRITE	1
+#define OPAL_I2C_SM_READ	2
+#define OPAL_I2C_SM_WRITE	3
+	uint8_t flags;
+#define OPAL_I2C_ADDR_10	0x01	/* Not supported yet */
+	uint8_t	subaddr_sz;		/* Max 4 */
+	uint8_t reserved;
+	__be16 addr;			/* 7 or 10 bit address */
+	__be16 reserved2;
+	__be32 subaddr;		/* Sub-address if any */
+	__be32 size;			/* Data size */
+	__be64 buffer_ra;		/* Buffer real address */
+};
+
 /* /sys/firmware/opal */
 extern struct kobject *opal_kobj;
 
@@ -876,11 +915,14 @@
 int64_t opal_handle_hmi(void);
 int64_t opal_register_dump_region(uint32_t id, uint64_t start, uint64_t end);
 int64_t opal_unregister_dump_region(uint32_t id);
+int64_t opal_slw_set_reg(uint64_t cpu_pir, uint64_t sprn, uint64_t val);
 int64_t opal_pci_set_phb_cxl_mode(uint64_t phb_id, uint64_t mode, uint64_t pe_number);
 int64_t opal_ipmi_send(uint64_t interface, struct opal_ipmi_msg *msg,
 		uint64_t msg_len);
 int64_t opal_ipmi_recv(uint64_t interface, struct opal_ipmi_msg *msg,
 		uint64_t *msg_len);
+int64_t opal_i2c_request(uint64_t async_token, uint32_t bus_id,
+			 struct opal_i2c_request *oreq);
 
 /* Internal functions */
 extern int early_init_dt_scan_opal(unsigned long node, const char *uname,
diff --git a/arch/powerpc/include/asm/paca.h b/arch/powerpc/include/asm/paca.h
index 24a386c..e5f22c6 100644
--- a/arch/powerpc/include/asm/paca.h
+++ b/arch/powerpc/include/asm/paca.h
@@ -152,6 +152,16 @@
 	u64 tm_scratch;                 /* TM scratch area for reclaim */
 #endif
 
+#ifdef CONFIG_PPC_POWERNV
+	/* Per-core mask tracking idle threads and a lock bit-[L][TTTTTTTT] */
+	u32 *core_idle_state_ptr;
+	u8 thread_idle_state;		/* PNV_THREAD_RUNNING/NAP/SLEEP	*/
+	/* Mask to indicate thread id in core */
+	u8 thread_mask;
+	/* Mask to denote subcore sibling threads */
+	u8 subcore_sibling_mask;
+#endif
+
 #ifdef CONFIG_PPC_BOOK3S_64
 	/* Exclusive emergency stack pointer for machine check exception. */
 	void *mc_emergency_sp;
diff --git a/arch/powerpc/include/asm/ppc-opcode.h b/arch/powerpc/include/asm/ppc-opcode.h
index 1a52877..03cd858 100644
--- a/arch/powerpc/include/asm/ppc-opcode.h
+++ b/arch/powerpc/include/asm/ppc-opcode.h
@@ -194,6 +194,7 @@
 
 #define PPC_INST_NAP			0x4c000364
 #define PPC_INST_SLEEP			0x4c0003a4
+#define PPC_INST_WINKLE			0x4c0003e4
 
 /* A2 specific instructions */
 #define PPC_INST_ERATWE			0x7c0001a6
@@ -375,6 +376,7 @@
 
 #define PPC_NAP			stringify_in_c(.long PPC_INST_NAP)
 #define PPC_SLEEP		stringify_in_c(.long PPC_INST_SLEEP)
+#define PPC_WINKLE		stringify_in_c(.long PPC_INST_WINKLE)
 
 /* BHRB instructions */
 #define PPC_CLRBHRB		stringify_in_c(.long PPC_INST_CLRBHRB)
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index 29c3798..bf117d8 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -452,7 +452,8 @@
 
 extern int powersave_nap;	/* set if nap mode can be used in idle loop */
 extern unsigned long power7_nap(int check_irq);
-extern void power7_sleep(void);
+extern unsigned long power7_sleep(void);
+extern unsigned long power7_winkle(void);
 extern void flush_instruction_cache(void);
 extern void hard_reset_now(void);
 extern void poweroff_now(void);
diff --git a/arch/powerpc/include/asm/reg.h b/arch/powerpc/include/asm/reg.h
index c998279..1c874fb 100644
--- a/arch/powerpc/include/asm/reg.h
+++ b/arch/powerpc/include/asm/reg.h
@@ -118,8 +118,10 @@
 #define __MSR		(MSR_ME | MSR_RI | MSR_IR | MSR_DR | MSR_ISF |MSR_HV)
 #ifdef __BIG_ENDIAN__
 #define MSR_		__MSR
+#define MSR_IDLE	(MSR_ME | MSR_SF | MSR_HV)
 #else
 #define MSR_		(__MSR | MSR_LE)
+#define MSR_IDLE	(MSR_ME | MSR_SF | MSR_HV | MSR_LE)
 #endif
 #define MSR_KERNEL	(MSR_ | MSR_64BIT)
 #define MSR_USER32	(MSR_ | MSR_PR | MSR_EE)
@@ -371,6 +373,7 @@
 #define SPRN_DBAT7L	0x23F	/* Data BAT 7 Lower Register */
 #define SPRN_DBAT7U	0x23E	/* Data BAT 7 Upper Register */
 #define SPRN_PPR	0x380	/* SMT Thread status Register */
+#define SPRN_TSCR	0x399	/* Thread Switch Control Register */
 
 #define SPRN_DEC	0x016		/* Decrement Register */
 #define SPRN_DER	0x095		/* Debug Enable Regsiter */
@@ -728,6 +731,7 @@
 #define SPRN_BESCR	806	/* Branch event status and control register */
 #define   BESCR_GE	0x8000000000000000ULL /* Global Enable */
 #define SPRN_WORT	895	/* Workload optimization register - thread */
+#define SPRN_WORC	863	/* Workload optimization register - core */
 
 #define SPRN_PMC1	787
 #define SPRN_PMC2	788
diff --git a/arch/powerpc/include/asm/syscall.h b/arch/powerpc/include/asm/syscall.h
index 6240698..ff21b7a 100644
--- a/arch/powerpc/include/asm/syscall.h
+++ b/arch/powerpc/include/asm/syscall.h
@@ -90,6 +90,10 @@
 
 static inline int syscall_get_arch(void)
 {
-	return is_32bit_task() ? AUDIT_ARCH_PPC : AUDIT_ARCH_PPC64;
+	int arch = is_32bit_task() ? AUDIT_ARCH_PPC : AUDIT_ARCH_PPC64;
+#ifdef __LITTLE_ENDIAN__
+	arch |= __AUDIT_ARCH_LE;
+#endif
+	return arch;
 }
 #endif	/* _ASM_SYSCALL_H */
diff --git a/arch/powerpc/include/asm/uaccess.h b/arch/powerpc/include/asm/uaccess.h
index 9485b43..a0c071d 100644
--- a/arch/powerpc/include/asm/uaccess.h
+++ b/arch/powerpc/include/asm/uaccess.h
@@ -284,7 +284,7 @@
 	if (!is_kernel_addr((unsigned long)__gu_addr))		\
 		might_fault();					\
 	__get_user_size(__gu_val, __gu_addr, (size), __gu_err);	\
-	(x) = (__typeof__(*(ptr)))__gu_val;			\
+	(x) = (__force __typeof__(*(ptr)))__gu_val;			\
 	__gu_err;						\
 })
 #endif /* __powerpc64__ */
@@ -297,7 +297,7 @@
 	might_fault();							\
 	if (access_ok(VERIFY_READ, __gu_addr, (size)))			\
 		__get_user_size(__gu_val, __gu_addr, (size), __gu_err);	\
-	(x) = (__typeof__(*(ptr)))__gu_val;				\
+	(x) = (__force __typeof__(*(ptr)))__gu_val;				\
 	__gu_err;							\
 })
 
@@ -308,7 +308,7 @@
 	const __typeof__(*(ptr)) __user *__gu_addr = (ptr);	\
 	__chk_user_ptr(ptr);					\
 	__get_user_size(__gu_val, __gu_addr, (size), __gu_err);	\
-	(x) = (__typeof__(*(ptr)))__gu_val;			\
+	(x) = (__force __typeof__(*(ptr)))__gu_val;			\
 	__gu_err;						\
 })
 
diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c
index 24d78e1..e624f96 100644
--- a/arch/powerpc/kernel/asm-offsets.c
+++ b/arch/powerpc/kernel/asm-offsets.c
@@ -726,5 +726,16 @@
 					arch.timing_last_enter.tv32.tbl));
 #endif
 
+#ifdef CONFIG_PPC_POWERNV
+	DEFINE(PACA_CORE_IDLE_STATE_PTR,
+			offsetof(struct paca_struct, core_idle_state_ptr));
+	DEFINE(PACA_THREAD_IDLE_STATE,
+			offsetof(struct paca_struct, thread_idle_state));
+	DEFINE(PACA_THREAD_MASK,
+			offsetof(struct paca_struct, thread_mask));
+	DEFINE(PACA_SUBCORE_SIBLING_MASK,
+			offsetof(struct paca_struct, subcore_sibling_mask));
+#endif
+
 	return 0;
 }
diff --git a/arch/powerpc/kernel/exceptions-64s.S b/arch/powerpc/kernel/exceptions-64s.S
index db08382..c2df815 100644
--- a/arch/powerpc/kernel/exceptions-64s.S
+++ b/arch/powerpc/kernel/exceptions-64s.S
@@ -15,6 +15,7 @@
 #include <asm/hw_irq.h>
 #include <asm/exception-64s.h>
 #include <asm/ptrace.h>
+#include <asm/cpuidle.h>
 
 /*
  * We layout physical memory as follows:
@@ -101,23 +102,34 @@
 #ifdef CONFIG_PPC_P7_NAP
 BEGIN_FTR_SECTION
 	/* Running native on arch 2.06 or later, check if we are
-	 * waking up from nap. We only handle no state loss and
-	 * supervisor state loss. We do -not- handle hypervisor
-	 * state loss at this time.
+	 * waking up from nap/sleep/winkle.
 	 */
 	mfspr	r13,SPRN_SRR1
 	rlwinm.	r13,r13,47-31,30,31
 	beq	9f
 
-	/* waking up from powersave (nap) state */
-	cmpwi	cr1,r13,2
-	/* Total loss of HV state is fatal, we could try to use the
-	 * PIR to locate a PACA, then use an emergency stack etc...
-	 * OPAL v3 based powernv platforms have new idle states
-	 * which fall in this catagory.
+	cmpwi	cr3,r13,2
+
+	/*
+	 * Check if last bit of HSPGR0 is set. This indicates whether we are
+	 * waking up from winkle.
 	 */
-	bgt	cr1,8f
 	GET_PACA(r13)
+	clrldi	r5,r13,63
+	clrrdi	r13,r13,1
+	cmpwi	cr4,r5,1
+	mtspr	SPRN_HSPRG0,r13
+
+	lbz	r0,PACA_THREAD_IDLE_STATE(r13)
+	cmpwi   cr2,r0,PNV_THREAD_NAP
+	bgt     cr2,8f				/* Either sleep or Winkle */
+
+	/* Waking up from nap should not cause hypervisor state loss */
+	bgt	cr3,.
+
+	/* Waking up from nap */
+	li	r0,PNV_THREAD_RUNNING
+	stb	r0,PACA_THREAD_IDLE_STATE(r13)	/* Clear thread state */
 
 #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
 	li	r0,KVM_HWTHREAD_IN_KERNEL
@@ -133,7 +145,7 @@
 
 	/* Return SRR1 from power7_nap() */
 	mfspr	r3,SPRN_SRR1
-	beq	cr1,2f
+	beq	cr3,2f
 	b	power7_wakeup_noloss
 2:	b	power7_wakeup_loss
 
@@ -1382,6 +1394,7 @@
 	MACHINE_CHECK_HANDLER_WINDUP
 	GET_PACA(r13)
 	ld	r1,PACAR1(r13)
+	li	r3,PNV_THREAD_NAP
 	b	power7_enter_nap_mode
 4:
 #endif
diff --git a/arch/powerpc/kernel/idle_power7.S b/arch/powerpc/kernel/idle_power7.S
index 18c0687..05adc8b 100644
--- a/arch/powerpc/kernel/idle_power7.S
+++ b/arch/powerpc/kernel/idle_power7.S
@@ -18,9 +18,25 @@
 #include <asm/hw_irq.h>
 #include <asm/kvm_book3s_asm.h>
 #include <asm/opal.h>
+#include <asm/cpuidle.h>
+#include <asm/mmu-hash64.h>
 
 #undef DEBUG
 
+/*
+ * Use unused space in the interrupt stack to save and restore
+ * registers for winkle support.
+ */
+#define _SDR1	GPR3
+#define _RPR	GPR4
+#define _SPURR	GPR5
+#define _PURR	GPR6
+#define _TSCR	GPR7
+#define _DSCR	GPR8
+#define _AMOR	GPR9
+#define _WORT	GPR10
+#define _WORC	GPR11
+
 /* Idle state entry routines */
 
 #define	IDLE_STATE_ENTER_SEQ(IDLE_INST)				\
@@ -37,8 +53,7 @@
 
 /*
  * Pass requested state in r3:
- * 	0 - nap
- * 	1 - sleep
+ *	r3 - PNV_THREAD_NAP/SLEEP/WINKLE
  *
  * To check IRQ_HAPPENED in r4
  * 	0 - don't check
@@ -101,18 +116,105 @@
 	std	r9,_MSR(r1)
 	std	r1,PACAR1(r13)
 
-_GLOBAL(power7_enter_nap_mode)
+	/*
+	 * Go to real mode to do the nap, as required by the architecture.
+	 * Also, we need to be in real mode before setting hwthread_state,
+	 * because as soon as we do that, another thread can switch
+	 * the MMU context to the guest.
+	 */
+	LOAD_REG_IMMEDIATE(r5, MSR_IDLE)
+	li	r6, MSR_RI
+	andc	r6, r9, r6
+	LOAD_REG_ADDR(r7, power7_enter_nap_mode)
+	mtmsrd	r6, 1		/* clear RI before setting SRR0/1 */
+	mtspr	SPRN_SRR0, r7
+	mtspr	SPRN_SRR1, r5
+	rfid
+
+	.globl	power7_enter_nap_mode
+power7_enter_nap_mode:
 #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
 	/* Tell KVM we're napping */
 	li	r4,KVM_HWTHREAD_IN_NAP
 	stb	r4,HSTATE_HWTHREAD_STATE(r13)
 #endif
-	cmpwi	cr0,r3,1
-	beq	2f
+	stb	r3,PACA_THREAD_IDLE_STATE(r13)
+	cmpwi	cr3,r3,PNV_THREAD_SLEEP
+	bge	cr3,2f
 	IDLE_STATE_ENTER_SEQ(PPC_NAP)
 	/* No return */
-2:	IDLE_STATE_ENTER_SEQ(PPC_SLEEP)
-	/* No return */
+2:
+	/* Sleep or winkle */
+	lbz	r7,PACA_THREAD_MASK(r13)
+	ld	r14,PACA_CORE_IDLE_STATE_PTR(r13)
+lwarx_loop1:
+	lwarx	r15,0,r14
+	andc	r15,r15,r7			/* Clear thread bit */
+
+	andi.	r15,r15,PNV_CORE_IDLE_THREAD_BITS
+
+/*
+ * If cr0 = 0, then current thread is the last thread of the core entering
+ * sleep. Last thread needs to execute the hardware bug workaround code if
+ * required by the platform.
+ * Make the workaround call unconditionally here. The below branch call is
+ * patched out when the idle states are discovered if the platform does not
+ * require it.
+ */
+.global pnv_fastsleep_workaround_at_entry
+pnv_fastsleep_workaround_at_entry:
+	beq	fastsleep_workaround_at_entry
+
+	stwcx.	r15,0,r14
+	bne-	lwarx_loop1
+	isync
+
+common_enter: /* common code for all the threads entering sleep or winkle */
+	bgt	cr3,enter_winkle
+	IDLE_STATE_ENTER_SEQ(PPC_SLEEP)
+
+fastsleep_workaround_at_entry:
+	ori	r15,r15,PNV_CORE_IDLE_LOCK_BIT
+	stwcx.	r15,0,r14
+	bne-	lwarx_loop1
+	isync
+
+	/* Fast sleep workaround */
+	li	r3,1
+	li	r4,1
+	li	r0,OPAL_CONFIG_CPU_IDLE_STATE
+	bl	opal_call_realmode
+
+	/* Clear Lock bit */
+	li	r0,0
+	lwsync
+	stw	r0,0(r14)
+	b	common_enter
+
+enter_winkle:
+	/*
+	 * Note all register i.e per-core, per-subcore or per-thread is saved
+	 * here since any thread in the core might wake up first
+	 */
+	mfspr	r3,SPRN_SDR1
+	std	r3,_SDR1(r1)
+	mfspr	r3,SPRN_RPR
+	std	r3,_RPR(r1)
+	mfspr	r3,SPRN_SPURR
+	std	r3,_SPURR(r1)
+	mfspr	r3,SPRN_PURR
+	std	r3,_PURR(r1)
+	mfspr	r3,SPRN_TSCR
+	std	r3,_TSCR(r1)
+	mfspr	r3,SPRN_DSCR
+	std	r3,_DSCR(r1)
+	mfspr	r3,SPRN_AMOR
+	std	r3,_AMOR(r1)
+	mfspr	r3,SPRN_WORT
+	std	r3,_WORT(r1)
+	mfspr	r3,SPRN_WORC
+	std	r3,_WORC(r1)
+	IDLE_STATE_ENTER_SEQ(PPC_WINKLE)
 
 _GLOBAL(power7_idle)
 	/* Now check if user or arch enabled NAP mode */
@@ -125,48 +227,21 @@
 
 _GLOBAL(power7_nap)
 	mr	r4,r3
-	li	r3,0
+	li	r3,PNV_THREAD_NAP
 	b	power7_powersave_common
 	/* No return */
 
 _GLOBAL(power7_sleep)
-	li	r3,1
+	li	r3,PNV_THREAD_SLEEP
 	li	r4,1
 	b	power7_powersave_common
 	/* No return */
 
-/*
- * Make opal call in realmode. This is a generic function to be called
- * from realmode from reset vector. It handles endianess.
- *
- * r13 - paca pointer
- * r1  - stack pointer
- * r3  - opal token
- */
-opal_call_realmode:
-	mflr	r12
-	std	r12,_LINK(r1)
-	ld	r2,PACATOC(r13)
-	/* Set opal return address */
-	LOAD_REG_ADDR(r0,return_from_opal_call)
-	mtlr	r0
-	/* Handle endian-ness */
-	li	r0,MSR_LE
-	mfmsr	r12
-	andc	r12,r12,r0
-	mtspr	SPRN_HSRR1,r12
-	mr	r0,r3			/* Move opal token to r0 */
-	LOAD_REG_ADDR(r11,opal)
-	ld	r12,8(r11)
-	ld	r2,0(r11)
-	mtspr	SPRN_HSRR0,r12
-	hrfid
-
-return_from_opal_call:
-	FIXUP_ENDIAN
-	ld	r0,_LINK(r1)
-	mtlr	r0
-	blr
+_GLOBAL(power7_winkle)
+	li	r3,3
+	li	r4,1
+	b	power7_powersave_common
+	/* No return */
 
 #define CHECK_HMI_INTERRUPT						\
 	mfspr	r0,SPRN_SRR1;						\
@@ -181,7 +256,7 @@
 	ld	r2,PACATOC(r13);					\
 	ld	r1,PACAR1(r13);						\
 	std	r3,ORIG_GPR3(r1);	/* Save original r3 */		\
-	li	r3,OPAL_HANDLE_HMI;	/* Pass opal token argument*/	\
+	li	r0,OPAL_HANDLE_HMI;	/* Pass opal token argument*/	\
 	bl	opal_call_realmode;					\
 	ld	r3,ORIG_GPR3(r1);	/* Restore original r3 */	\
 20:	nop;
@@ -190,16 +265,190 @@
 _GLOBAL(power7_wakeup_tb_loss)
 	ld	r2,PACATOC(r13);
 	ld	r1,PACAR1(r13)
+	/*
+	 * Before entering any idle state, the NVGPRs are saved in the stack
+	 * and they are restored before switching to the process context. Hence
+	 * until they are restored, they are free to be used.
+	 *
+	 * Save SRR1 in a NVGPR as it might be clobbered in opal_call_realmode
+	 * (called in CHECK_HMI_INTERRUPT). SRR1 is required to determine the
+	 * wakeup reason if we branch to kvm_start_guest.
+	 */
 
+	mfspr	r16,SPRN_SRR1
 BEGIN_FTR_SECTION
 	CHECK_HMI_INTERRUPT
 END_FTR_SECTION_IFSET(CPU_FTR_HVMODE)
-	/* Time base re-sync */
-	li	r3,OPAL_RESYNC_TIMEBASE
-	bl	opal_call_realmode;
 
+	lbz	r7,PACA_THREAD_MASK(r13)
+	ld	r14,PACA_CORE_IDLE_STATE_PTR(r13)
+lwarx_loop2:
+	lwarx	r15,0,r14
+	andi.	r9,r15,PNV_CORE_IDLE_LOCK_BIT
+	/*
+	 * Lock bit is set in one of the 2 cases-
+	 * a. In the sleep/winkle enter path, the last thread is executing
+	 * fastsleep workaround code.
+	 * b. In the wake up path, another thread is executing fastsleep
+	 * workaround undo code or resyncing timebase or restoring context
+	 * In either case loop until the lock bit is cleared.
+	 */
+	bne	core_idle_lock_held
+
+	cmpwi	cr2,r15,0
+	lbz	r4,PACA_SUBCORE_SIBLING_MASK(r13)
+	and	r4,r4,r15
+	cmpwi	cr1,r4,0	/* Check if first in subcore */
+
+	/*
+	 * At this stage
+	 * cr1 - 0b0100 if first thread to wakeup in subcore
+	 * cr2 - 0b0100 if first thread to wakeup in core
+	 * cr3-  0b0010 if waking up from sleep or winkle
+	 * cr4 - 0b0100 if waking up from winkle
+	 */
+
+	or	r15,r15,r7		/* Set thread bit */
+
+	beq	cr1,first_thread_in_subcore
+
+	/* Not first thread in subcore to wake up */
+	stwcx.	r15,0,r14
+	bne-	lwarx_loop2
+	isync
+	b	common_exit
+
+core_idle_lock_held:
+	HMT_LOW
+core_idle_lock_loop:
+	lwz	r15,0(14)
+	andi.   r9,r15,PNV_CORE_IDLE_LOCK_BIT
+	bne	core_idle_lock_loop
+	HMT_MEDIUM
+	b	lwarx_loop2
+
+first_thread_in_subcore:
+	/* First thread in subcore to wakeup */
+	ori	r15,r15,PNV_CORE_IDLE_LOCK_BIT
+	stwcx.	r15,0,r14
+	bne-	lwarx_loop2
+	isync
+
+	/*
+	 * If waking up from sleep, subcore state is not lost. Hence
+	 * skip subcore state restore
+	 */
+	bne	cr4,subcore_state_restored
+
+	/* Restore per-subcore state */
+	ld      r4,_SDR1(r1)
+	mtspr   SPRN_SDR1,r4
+	ld      r4,_RPR(r1)
+	mtspr   SPRN_RPR,r4
+	ld	r4,_AMOR(r1)
+	mtspr	SPRN_AMOR,r4
+
+subcore_state_restored:
+	/*
+	 * Check if the thread is also the first thread in the core. If not,
+	 * skip to clear_lock.
+	 */
+	bne	cr2,clear_lock
+
+first_thread_in_core:
+
+	/*
+	 * First thread in the core waking up from fastsleep. It needs to
+	 * call the fastsleep workaround code if the platform requires it.
+	 * Call it unconditionally here. The below branch instruction will
+	 * be patched out when the idle states are discovered if platform
+	 * does not require workaround.
+	 */
+.global pnv_fastsleep_workaround_at_exit
+pnv_fastsleep_workaround_at_exit:
+	b	fastsleep_workaround_at_exit
+
+timebase_resync:
+	/* Do timebase resync if we are waking up from sleep. Use cr3 value
+	 * set in exceptions-64s.S */
+	ble	cr3,clear_lock
+	/* Time base re-sync */
+	li	r0,OPAL_RESYNC_TIMEBASE
+	bl	opal_call_realmode;
 	/* TODO: Check r3 for failure */
 
+	/*
+	 * If waking up from sleep, per core state is not lost, skip to
+	 * clear_lock.
+	 */
+	bne	cr4,clear_lock
+
+	/* Restore per core state */
+	ld	r4,_TSCR(r1)
+	mtspr	SPRN_TSCR,r4
+	ld	r4,_WORC(r1)
+	mtspr	SPRN_WORC,r4
+
+clear_lock:
+	andi.	r15,r15,PNV_CORE_IDLE_THREAD_BITS
+	lwsync
+	stw	r15,0(r14)
+
+common_exit:
+	/*
+	 * Common to all threads.
+	 *
+	 * If waking up from sleep, hypervisor state is not lost. Hence
+	 * skip hypervisor state restore.
+	 */
+	bne	cr4,hypervisor_state_restored
+
+	/* Waking up from winkle */
+
+	/* Restore per thread state */
+	bl	__restore_cpu_power8
+
+	/* Restore SLB  from PACA */
+	ld	r8,PACA_SLBSHADOWPTR(r13)
+
+	.rept	SLB_NUM_BOLTED
+	li	r3, SLBSHADOW_SAVEAREA
+	LDX_BE	r5, r8, r3
+	addi	r3, r3, 8
+	LDX_BE	r6, r8, r3
+	andis.	r7,r5,SLB_ESID_V@h
+	beq	1f
+	slbmte	r6,r5
+1:	addi	r8,r8,16
+	.endr
+
+	ld	r4,_SPURR(r1)
+	mtspr	SPRN_SPURR,r4
+	ld	r4,_PURR(r1)
+	mtspr	SPRN_PURR,r4
+	ld	r4,_DSCR(r1)
+	mtspr	SPRN_DSCR,r4
+	ld	r4,_WORT(r1)
+	mtspr	SPRN_WORT,r4
+
+hypervisor_state_restored:
+
+	li	r5,PNV_THREAD_RUNNING
+	stb     r5,PACA_THREAD_IDLE_STATE(r13)
+
+	mtspr	SPRN_SRR1,r16
+#ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE
+	li      r0,KVM_HWTHREAD_IN_KERNEL
+	stb     r0,HSTATE_HWTHREAD_STATE(r13)
+	/* Order setting hwthread_state vs. testing hwthread_req */
+	sync
+	lbz     r0,HSTATE_HWTHREAD_REQ(r13)
+	cmpwi   r0,0
+	beq     6f
+	b       kvm_start_guest
+6:
+#endif
+
 	REST_NVGPRS(r1)
 	REST_GPR(2, r1)
 	ld	r3,_CCR(r1)
@@ -212,6 +461,13 @@
 	mtspr	SPRN_SRR0,r5
 	rfid
 
+fastsleep_workaround_at_exit:
+	li	r3,1
+	li	r4,0
+	li	r0,OPAL_CONFIG_CPU_IDLE_STATE
+	bl	opal_call_realmode
+	b	timebase_resync
+
 /*
  * R3 here contains the value that will be returned to the caller
  * of power7_nap.
diff --git a/arch/powerpc/kernel/smp.c b/arch/powerpc/kernel/smp.c
index 8b2d2dc..8ec017c 100644
--- a/arch/powerpc/kernel/smp.c
+++ b/arch/powerpc/kernel/smp.c
@@ -700,7 +700,6 @@
 	smp_store_cpu_info(cpu);
 	set_dec(tb_ticks_per_jiffy);
 	preempt_disable();
-	cpu_callin_map[cpu] = 1;
 
 	if (smp_ops->setup_cpu)
 		smp_ops->setup_cpu(cpu);
@@ -739,6 +738,14 @@
 	notify_cpu_starting(cpu);
 	set_cpu_online(cpu, true);
 
+	/*
+	 * CPU must be marked active and online before we signal back to the
+	 * master, because the scheduler needs to see the cpu_online and
+	 * cpu_active bits set.
+	 */
+	smp_wmb();
+	cpu_callin_map[cpu] = 1;
+
 	local_irq_enable();
 
 	cpu_startup_entry(CPUHP_ONLINE);
diff --git a/arch/powerpc/perf/hv-24x7.c b/arch/powerpc/perf/hv-24x7.c
index dba3408..f162d0b 100644
--- a/arch/powerpc/perf/hv-24x7.c
+++ b/arch/powerpc/perf/hv-24x7.c
@@ -177,7 +177,7 @@
 	}							\
 	ret = sprintf(buf, _fmt, _expr);			\
 e_free:								\
-	kfree(page);						\
+	kmem_cache_free(hv_page_cache, page);			\
 	return ret;						\
 }								\
 static DEVICE_ATTR_RO(_name)
@@ -217,11 +217,14 @@
 		domain == HV_24X7_PERF_DOMAIN_PHYSICAL_CORE;
 }
 
+DEFINE_PER_CPU(char, hv_24x7_reqb[4096]) __aligned(4096);
+DEFINE_PER_CPU(char, hv_24x7_resb[4096]) __aligned(4096);
+
 static unsigned long single_24x7_request(u8 domain, u32 offset, u16 ix,
 					 u16 lpar, u64 *res,
 					 bool success_expected)
 {
-	unsigned long ret = -ENOMEM;
+	unsigned long ret;
 
 	/*
 	 * request_buffer and result_buffer are not required to be 4k aligned,
@@ -243,13 +246,11 @@
 	BUILD_BUG_ON(sizeof(*request_buffer) > 4096);
 	BUILD_BUG_ON(sizeof(*result_buffer) > 4096);
 
-	request_buffer = kmem_cache_zalloc(hv_page_cache, GFP_USER);
-	if (!request_buffer)
-		goto out;
+	request_buffer = (void *)get_cpu_var(hv_24x7_reqb);
+	result_buffer = (void *)get_cpu_var(hv_24x7_resb);
 
-	result_buffer = kmem_cache_zalloc(hv_page_cache, GFP_USER);
-	if (!result_buffer)
-		goto out_free_request_buffer;
+	memset(request_buffer, 0, 4096);
+	memset(result_buffer, 0, 4096);
 
 	*request_buffer = (struct reqb) {
 		.buf = {
@@ -278,15 +279,11 @@
 				domain, offset, ix, lpar, ret, ret,
 				result_buffer->buf.detailed_rc,
 				result_buffer->buf.failing_request_ix);
-		goto out_free_result_buffer;
+		goto out;
 	}
 
 	*res = be64_to_cpu(result_buffer->result);
 
-out_free_result_buffer:
-	kfree(result_buffer);
-out_free_request_buffer:
-	kfree(request_buffer);
 out:
 	return ret;
 }
diff --git a/arch/powerpc/platforms/powernv/opal-wrappers.S b/arch/powerpc/platforms/powernv/opal-wrappers.S
index 0a299be..54eca8b 100644
--- a/arch/powerpc/platforms/powernv/opal-wrappers.S
+++ b/arch/powerpc/platforms/powernv/opal-wrappers.S
@@ -158,6 +158,43 @@
 	blr
 #endif
 
+/*
+ * Make opal call in realmode. This is a generic function to be called
+ * from realmode. It handles endianness.
+ *
+ * r13 - paca pointer
+ * r1  - stack pointer
+ * r0  - opal token
+ */
+_GLOBAL(opal_call_realmode)
+	mflr	r12
+	std	r12,PPC_LR_STKOFF(r1)
+	ld	r2,PACATOC(r13)
+	/* Set opal return address */
+	LOAD_REG_ADDR(r12,return_from_opal_call)
+	mtlr	r12
+
+	mfmsr	r12
+#ifdef __LITTLE_ENDIAN__
+	/* Handle endian-ness */
+	li	r11,MSR_LE
+	andc	r12,r12,r11
+#endif
+	mtspr	SPRN_HSRR1,r12
+	LOAD_REG_ADDR(r11,opal)
+	ld	r12,8(r11)
+	ld	r2,0(r11)
+	mtspr	SPRN_HSRR0,r12
+	hrfid
+
+return_from_opal_call:
+#ifdef __LITTLE_ENDIAN__
+	FIXUP_ENDIAN
+#endif
+	ld	r12,PPC_LR_STKOFF(r1)
+	mtlr	r12
+	blr
+
 OPAL_CALL(opal_invalid_call,			OPAL_INVALID_CALL);
 OPAL_CALL(opal_console_write,			OPAL_CONSOLE_WRITE);
 OPAL_CALL(opal_console_read,			OPAL_CONSOLE_READ);
@@ -247,6 +284,7 @@
 OPAL_CALL(opal_get_param,			OPAL_GET_PARAM);
 OPAL_CALL(opal_set_param,			OPAL_SET_PARAM);
 OPAL_CALL(opal_handle_hmi,			OPAL_HANDLE_HMI);
+OPAL_CALL(opal_slw_set_reg,			OPAL_SLW_SET_REG);
 OPAL_CALL(opal_register_dump_region,		OPAL_REGISTER_DUMP_REGION);
 OPAL_CALL(opal_unregister_dump_region,		OPAL_UNREGISTER_DUMP_REGION);
 OPAL_CALL(opal_pci_set_phb_cxl_mode,		OPAL_PCI_SET_PHB_CXL_MODE);
@@ -254,3 +292,4 @@
 OPAL_CALL(opal_tpo_read,			OPAL_READ_TPO);
 OPAL_CALL(opal_ipmi_send,			OPAL_IPMI_SEND);
 OPAL_CALL(opal_ipmi_recv,			OPAL_IPMI_RECV);
+OPAL_CALL(opal_i2c_request,			OPAL_I2C_REQUEST);
diff --git a/arch/powerpc/platforms/powernv/opal.c b/arch/powerpc/platforms/powernv/opal.c
index cb0b6de..f10b9ec 100644
--- a/arch/powerpc/platforms/powernv/opal.c
+++ b/arch/powerpc/platforms/powernv/opal.c
@@ -9,8 +9,9 @@
  * 2 of the License, or (at your option) any later version.
  */
 
-#undef DEBUG
+#define pr_fmt(fmt)	"opal: " fmt
 
+#include <linux/printk.h>
 #include <linux/types.h>
 #include <linux/of.h>
 #include <linux/of_fdt.h>
@@ -625,6 +626,39 @@
 	return 0;
 }
 
+static ssize_t symbol_map_read(struct file *fp, struct kobject *kobj,
+			       struct bin_attribute *bin_attr,
+			       char *buf, loff_t off, size_t count)
+{
+	return memory_read_from_buffer(buf, count, &off, bin_attr->private,
+				       bin_attr->size);
+}
+
+static BIN_ATTR_RO(symbol_map, 0);
+
+static void opal_export_symmap(void)
+{
+	const __be64 *syms;
+	unsigned int size;
+	struct device_node *fw;
+	int rc;
+
+	fw = of_find_node_by_path("/ibm,opal/firmware");
+	if (!fw)
+		return;
+	syms = of_get_property(fw, "symbol-map", &size);
+	if (!syms || size != 2 * sizeof(__be64))
+		return;
+
+	/* Setup attributes */
+	bin_attr_symbol_map.private = __va(be64_to_cpu(syms[0]));
+	bin_attr_symbol_map.size = be64_to_cpu(syms[1]);
+
+	rc = sysfs_create_bin_file(opal_kobj, &bin_attr_symbol_map);
+	if (rc)
+		pr_warn("Error %d creating OPAL symbols file\n", rc);
+}
+
 static void __init opal_dump_region_init(void)
 {
 	void *addr;
@@ -653,6 +687,14 @@
 			of_platform_device_create(np, NULL, NULL);
 }
 
+static void opal_i2c_create_devs(void)
+{
+	struct device_node *np;
+
+	for_each_compatible_node(np, NULL, "ibm,opal-i2c")
+		of_platform_device_create(np, NULL, NULL);
+}
+
 static int __init opal_init(void)
 {
 	struct device_node *np, *consoles;
@@ -679,6 +721,9 @@
 		of_node_put(consoles);
 	}
 
+	/* Create i2c platform devices */
+	opal_i2c_create_devs();
+
 	/* Find all OPAL interrupts and request them */
 	irqs = of_get_property(opal_node, "opal-interrupts", &irqlen);
 	pr_debug("opal: Found %d interrupts reserved for OPAL\n",
@@ -702,6 +747,8 @@
 	/* Create "opal" kobject under /sys/firmware */
 	rc = opal_sysfs_init();
 	if (rc == 0) {
+		/* Export symbol map to userspace */
+		opal_export_symmap();
 		/* Setup dump region interface */
 		opal_dump_region_init();
 		/* Setup error log interface */
@@ -824,3 +871,4 @@
 EXPORT_SYMBOL_GPL(opal_rtc_write);
 EXPORT_SYMBOL_GPL(opal_tpo_read);
 EXPORT_SYMBOL_GPL(opal_tpo_write);
+EXPORT_SYMBOL_GPL(opal_i2c_request);
diff --git a/arch/powerpc/platforms/powernv/powernv.h b/arch/powerpc/platforms/powernv/powernv.h
index 6c8e2d1..604c48e 100644
--- a/arch/powerpc/platforms/powernv/powernv.h
+++ b/arch/powerpc/platforms/powernv/powernv.h
@@ -29,6 +29,8 @@
 }
 #endif
 
+extern u32 pnv_get_supported_cpuidle_states(void);
+
 extern void pnv_lpc_init(void);
 
 bool cpu_core_split_required(void);
diff --git a/arch/powerpc/platforms/powernv/setup.c b/arch/powerpc/platforms/powernv/setup.c
index 30b1c3e..b700a32 100644
--- a/arch/powerpc/platforms/powernv/setup.c
+++ b/arch/powerpc/platforms/powernv/setup.c
@@ -36,8 +36,12 @@
 #include <asm/opal.h>
 #include <asm/kexec.h>
 #include <asm/smp.h>
+#include <asm/cputhreads.h>
+#include <asm/cpuidle.h>
+#include <asm/code-patching.h>
 
 #include "powernv.h"
+#include "subcore.h"
 
 static void __init pnv_setup_arch(void)
 {
@@ -288,6 +292,168 @@
 }
 #endif /* CONFIG_PPC_POWERNV_RTAS */
 
+static u32 supported_cpuidle_states;
+
+int pnv_save_sprs_for_winkle(void)
+{
+	int cpu;
+	int rc;
+
+	/*
+	 * hid0, hid1, hid4, hid5, hmeer and lpcr values are symmetric accross
+	 * all cpus at boot. Get these reg values of current cpu and use the
+	 * same accross all cpus.
+	 */
+	uint64_t lpcr_val = mfspr(SPRN_LPCR);
+	uint64_t hid0_val = mfspr(SPRN_HID0);
+	uint64_t hid1_val = mfspr(SPRN_HID1);
+	uint64_t hid4_val = mfspr(SPRN_HID4);
+	uint64_t hid5_val = mfspr(SPRN_HID5);
+	uint64_t hmeer_val = mfspr(SPRN_HMEER);
+
+	for_each_possible_cpu(cpu) {
+		uint64_t pir = get_hard_smp_processor_id(cpu);
+		uint64_t hsprg0_val = (uint64_t)&paca[cpu];
+
+		/*
+		 * HSPRG0 is used to store the cpu's pointer to paca. Hence last
+		 * 3 bits are guaranteed to be 0. Program slw to restore HSPRG0
+		 * with 63rd bit set, so that when a thread wakes up at 0x100 we
+		 * can use this bit to distinguish between fastsleep and
+		 * deep winkle.
+		 */
+		hsprg0_val |= 1;
+
+		rc = opal_slw_set_reg(pir, SPRN_HSPRG0, hsprg0_val);
+		if (rc != 0)
+			return rc;
+
+		rc = opal_slw_set_reg(pir, SPRN_LPCR, lpcr_val);
+		if (rc != 0)
+			return rc;
+
+		/* HIDs are per core registers */
+		if (cpu_thread_in_core(cpu) == 0) {
+
+			rc = opal_slw_set_reg(pir, SPRN_HMEER, hmeer_val);
+			if (rc != 0)
+				return rc;
+
+			rc = opal_slw_set_reg(pir, SPRN_HID0, hid0_val);
+			if (rc != 0)
+				return rc;
+
+			rc = opal_slw_set_reg(pir, SPRN_HID1, hid1_val);
+			if (rc != 0)
+				return rc;
+
+			rc = opal_slw_set_reg(pir, SPRN_HID4, hid4_val);
+			if (rc != 0)
+				return rc;
+
+			rc = opal_slw_set_reg(pir, SPRN_HID5, hid5_val);
+			if (rc != 0)
+				return rc;
+		}
+	}
+
+	return 0;
+}
+
+static void pnv_alloc_idle_core_states(void)
+{
+	int i, j;
+	int nr_cores = cpu_nr_cores();
+	u32 *core_idle_state;
+
+	/*
+	 * core_idle_state - First 8 bits track the idle state of each thread
+	 * of the core. The 8th bit is the lock bit. Initially all thread bits
+	 * are set. They are cleared when the thread enters deep idle state
+	 * like sleep and winkle. Initially the lock bit is cleared.
+	 * The lock bit has 2 purposes
+	 * a. While the first thread is restoring core state, it prevents
+	 * other threads in the core from switching to process context.
+	 * b. While the last thread in the core is saving the core state, it
+	 * prevents a different thread from waking up.
+	 */
+	for (i = 0; i < nr_cores; i++) {
+		int first_cpu = i * threads_per_core;
+		int node = cpu_to_node(first_cpu);
+
+		core_idle_state = kmalloc_node(sizeof(u32), GFP_KERNEL, node);
+		*core_idle_state = PNV_CORE_IDLE_THREAD_BITS;
+
+		for (j = 0; j < threads_per_core; j++) {
+			int cpu = first_cpu + j;
+
+			paca[cpu].core_idle_state_ptr = core_idle_state;
+			paca[cpu].thread_idle_state = PNV_THREAD_RUNNING;
+			paca[cpu].thread_mask = 1 << j;
+		}
+	}
+
+	update_subcore_sibling_mask();
+
+	if (supported_cpuidle_states & OPAL_PM_WINKLE_ENABLED)
+		pnv_save_sprs_for_winkle();
+}
+
+u32 pnv_get_supported_cpuidle_states(void)
+{
+	return supported_cpuidle_states;
+}
+EXPORT_SYMBOL_GPL(pnv_get_supported_cpuidle_states);
+
+static int __init pnv_init_idle_states(void)
+{
+	struct device_node *power_mgt;
+	int dt_idle_states;
+	const __be32 *idle_state_flags;
+	u32 len_flags, flags;
+	int i;
+
+	supported_cpuidle_states = 0;
+
+	if (cpuidle_disable != IDLE_NO_OVERRIDE)
+		return 0;
+
+	if (!firmware_has_feature(FW_FEATURE_OPALv3))
+		return 0;
+
+	power_mgt = of_find_node_by_path("/ibm,opal/power-mgt");
+	if (!power_mgt) {
+		pr_warn("opal: PowerMgmt Node not found\n");
+		return 0;
+	}
+
+	idle_state_flags = of_get_property(power_mgt,
+			"ibm,cpu-idle-state-flags", &len_flags);
+	if (!idle_state_flags) {
+		pr_warn("DT-PowerMgmt: missing ibm,cpu-idle-state-flags\n");
+		return 0;
+	}
+
+	dt_idle_states = len_flags / sizeof(u32);
+
+	for (i = 0; i < dt_idle_states; i++) {
+		flags = be32_to_cpu(idle_state_flags[i]);
+		supported_cpuidle_states |= flags;
+	}
+	if (!(supported_cpuidle_states & OPAL_PM_SLEEP_ENABLED_ER1)) {
+		patch_instruction(
+			(unsigned int *)pnv_fastsleep_workaround_at_entry,
+			PPC_INST_NOP);
+		patch_instruction(
+			(unsigned int *)pnv_fastsleep_workaround_at_exit,
+			PPC_INST_NOP);
+	}
+	pnv_alloc_idle_core_states();
+	return 0;
+}
+
+subsys_initcall(pnv_init_idle_states);
+
 static int __init pnv_probe(void)
 {
 	unsigned long root = of_get_flat_dt_root();
diff --git a/arch/powerpc/platforms/powernv/smp.c b/arch/powerpc/platforms/powernv/smp.c
index b716f66..fc34025 100644
--- a/arch/powerpc/platforms/powernv/smp.c
+++ b/arch/powerpc/platforms/powernv/smp.c
@@ -150,6 +150,7 @@
 {
 	unsigned int cpu;
 	unsigned long srr1;
+	u32 idle_states;
 
 	/* Standard hot unplug procedure */
 	local_irq_disable();
@@ -160,13 +161,23 @@
 	generic_set_cpu_dead(cpu);
 	smp_wmb();
 
+	idle_states = pnv_get_supported_cpuidle_states();
 	/* We don't want to take decrementer interrupts while we are offline,
 	 * so clear LPCR:PECE1. We keep PECE2 enabled.
 	 */
 	mtspr(SPRN_LPCR, mfspr(SPRN_LPCR) & ~(u64)LPCR_PECE1);
 	while (!generic_check_cpu_restart(cpu)) {
+
 		ppc64_runlatch_off();
-		srr1 = power7_nap(1);
+
+		if (idle_states & OPAL_PM_WINKLE_ENABLED)
+			srr1 = power7_winkle();
+		else if ((idle_states & OPAL_PM_SLEEP_ENABLED) ||
+				(idle_states & OPAL_PM_SLEEP_ENABLED_ER1))
+			srr1 = power7_sleep();
+		else
+			srr1 = power7_nap(1);
+
 		ppc64_runlatch_on();
 
 		/*
@@ -198,13 +209,27 @@
 
 #endif /* CONFIG_HOTPLUG_CPU */
 
+static int pnv_cpu_bootable(unsigned int nr)
+{
+	/*
+	 * Starting with POWER8, the subcore logic relies on all threads of a
+	 * core being booted so that they can participate in split mode
+	 * switches. So on those machines we ignore the smt_enabled_at_boot
+	 * setting (smt-enabled on the kernel command line).
+	 */
+	if (cpu_has_feature(CPU_FTR_ARCH_207S))
+		return 1;
+
+	return smp_generic_cpu_bootable(nr);
+}
+
 static struct smp_ops_t pnv_smp_ops = {
 	.message_pass	= smp_muxed_ipi_message_pass,
 	.cause_ipi	= NULL,	/* Filled at runtime by xics_smp_probe() */
 	.probe		= xics_smp_probe,
 	.kick_cpu	= pnv_smp_kick_cpu,
 	.setup_cpu	= pnv_smp_setup_cpu,
-	.cpu_bootable	= smp_generic_cpu_bootable,
+	.cpu_bootable	= pnv_cpu_bootable,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_disable	= pnv_smp_cpu_disable,
 	.cpu_die	= generic_cpu_die,
diff --git a/arch/powerpc/platforms/powernv/subcore.c b/arch/powerpc/platforms/powernv/subcore.c
index c87f96b..f60f80a 100644
--- a/arch/powerpc/platforms/powernv/subcore.c
+++ b/arch/powerpc/platforms/powernv/subcore.c
@@ -160,6 +160,18 @@
 	mb();
 }
 
+static void update_hid_in_slw(u64 hid0)
+{
+	u64 idle_states = pnv_get_supported_cpuidle_states();
+
+	if (idle_states & OPAL_PM_WINKLE_ENABLED) {
+		/* OPAL call to patch slw with the new HID0 value */
+		u64 cpu_pir = hard_smp_processor_id();
+
+		opal_slw_set_reg(cpu_pir, SPRN_HID0, hid0);
+	}
+}
+
 static void unsplit_core(void)
 {
 	u64 hid0, mask;
@@ -179,6 +191,7 @@
 	hid0 = mfspr(SPRN_HID0);
 	hid0 &= ~HID0_POWER8_DYNLPARDIS;
 	mtspr(SPRN_HID0, hid0);
+	update_hid_in_slw(hid0);
 
 	while (mfspr(SPRN_HID0) & mask)
 		cpu_relax();
@@ -215,6 +228,7 @@
 	hid0  = mfspr(SPRN_HID0);
 	hid0 |= HID0_POWER8_DYNLPARDIS | split_parms[i].value;
 	mtspr(SPRN_HID0, hid0);
+	update_hid_in_slw(hid0);
 
 	/* Wait for it to happen */
 	while (!(mfspr(SPRN_HID0) & split_parms[i].mask))
@@ -251,6 +265,25 @@
 	return true;
 }
 
+void update_subcore_sibling_mask(void)
+{
+	int cpu;
+	/*
+	 * sibling mask for the first cpu. Left shift this by required bits
+	 * to get sibling mask for the rest of the cpus.
+	 */
+	int sibling_mask_first_cpu =  (1 << threads_per_subcore) - 1;
+
+	for_each_possible_cpu(cpu) {
+		int tid = cpu_thread_in_core(cpu);
+		int offset = (tid / threads_per_subcore) * threads_per_subcore;
+		int mask = sibling_mask_first_cpu << offset;
+
+		paca[cpu].subcore_sibling_mask = mask;
+
+	}
+}
+
 static int cpu_update_split_mode(void *data)
 {
 	int cpu, new_mode = *(int *)data;
@@ -284,6 +317,7 @@
 		/* Make the new mode public */
 		subcores_per_core = new_mode;
 		threads_per_subcore = threads_per_core / subcores_per_core;
+		update_subcore_sibling_mask();
 
 		/* Make sure the new mode is written before we exit */
 		mb();
diff --git a/arch/powerpc/platforms/powernv/subcore.h b/arch/powerpc/platforms/powernv/subcore.h
index 148abc9..84e02ae 100644
--- a/arch/powerpc/platforms/powernv/subcore.h
+++ b/arch/powerpc/platforms/powernv/subcore.h
@@ -14,5 +14,12 @@
 #define SYNC_STEP_FINISHED	3	/* Set by secondary when split/unsplit is done */
 
 #ifndef __ASSEMBLY__
+
+#ifdef CONFIG_SMP
 void split_core_secondary_loop(u8 *state);
-#endif
+extern void update_subcore_sibling_mask(void);
+#else
+static inline void update_subcore_sibling_mask(void) { };
+#endif /* CONFIG_SMP */
+
+#endif /* __ASSEMBLY__ */
diff --git a/drivers/cpuidle/cpuidle-powernv.c b/drivers/cpuidle/cpuidle-powernv.c
index e9248bb..aedec09 100644
--- a/drivers/cpuidle/cpuidle-powernv.c
+++ b/drivers/cpuidle/cpuidle-powernv.c
@@ -16,13 +16,10 @@
 
 #include <asm/machdep.h>
 #include <asm/firmware.h>
+#include <asm/opal.h>
 #include <asm/runlatch.h>
 
-/* Flags and constants used in PowerNV platform */
-
 #define MAX_POWERNV_IDLE_STATES	8
-#define IDLE_USE_INST_NAP	0x00010000 /* Use nap instruction */
-#define IDLE_USE_INST_SLEEP	0x00020000 /* Use sleep instruction */
 
 struct cpuidle_driver powernv_idle_driver = {
 	.name             = "powernv_idle",
@@ -197,7 +194,7 @@
 		 * target residency to be 10x exit_latency
 		 */
 		latency_ns = be32_to_cpu(idle_state_latency[i]);
-		if (flags & IDLE_USE_INST_NAP) {
+		if (flags & OPAL_PM_NAP_ENABLED) {
 			/* Add NAP state */
 			strcpy(powernv_states[nr_idle_states].name, "Nap");
 			strcpy(powernv_states[nr_idle_states].desc, "Nap");
@@ -210,7 +207,8 @@
 			nr_idle_states++;
 		}
 
-		if (flags & IDLE_USE_INST_SLEEP) {
+		if (flags & OPAL_PM_SLEEP_ENABLED ||
+			flags & OPAL_PM_SLEEP_ENABLED_ER1) {
 			/* Add FASTSLEEP state */
 			strcpy(powernv_states[nr_idle_states].name, "FastSleep");
 			strcpy(powernv_states[nr_idle_states].desc, "FastSleep");
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index c1351d9..91a488c 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -1072,4 +1072,15 @@
 	  This support is also available as a module.  If so, the module
 	  will be called scx200_acb.
 
+config I2C_OPAL
+	tristate "IBM OPAL I2C driver"
+	depends on PPC_POWERNV
+	default y
+	help
+	  This exposes the PowerNV platform i2c busses to the linux i2c layer,
+	  the driver is based on the OPAL interfaces.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called as i2c-opal.
+
 endmenu
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 5e6c822..56388f6 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -102,6 +102,7 @@
 obj-$(CONFIG_I2C_BCM_KONA)	+= i2c-bcm-kona.o
 obj-$(CONFIG_I2C_CROS_EC_TUNNEL)	+= i2c-cros-ec-tunnel.o
 obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o
+obj-$(CONFIG_I2C_OPAL)		+= i2c-opal.o
 obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
 obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
 obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
diff --git a/drivers/i2c/busses/i2c-opal.c b/drivers/i2c/busses/i2c-opal.c
new file mode 100644
index 0000000..16f90b1
--- /dev/null
+++ b/drivers/i2c/busses/i2c-opal.c
@@ -0,0 +1,294 @@
+/*
+ * IBM OPAL I2C driver
+ * Copyright (C) 2014 IBM
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.
+ */
+
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <asm/firmware.h>
+#include <asm/opal.h>
+
+static int i2c_opal_translate_error(int rc)
+{
+	switch (rc) {
+	case OPAL_NO_MEM:
+		return -ENOMEM;
+	case OPAL_PARAMETER:
+		return -EINVAL;
+	case OPAL_I2C_ARBT_LOST:
+		return -EAGAIN;
+	case OPAL_I2C_TIMEOUT:
+		return -ETIMEDOUT;
+	case OPAL_I2C_NACK_RCVD:
+		return -ENXIO;
+	case OPAL_I2C_STOP_ERR:
+		return -EBUSY;
+	default:
+		return -EIO;
+	}
+}
+
+static int i2c_opal_send_request(u32 bus_id, struct opal_i2c_request *req)
+{
+	struct opal_msg msg;
+	int token, rc;
+
+	token = opal_async_get_token_interruptible();
+	if (token < 0) {
+		if (token != -ERESTARTSYS)
+			pr_err("Failed to get the async token\n");
+
+		return token;
+	}
+
+	rc = opal_i2c_request(token, bus_id, req);
+	if (rc != OPAL_ASYNC_COMPLETION) {
+		rc = i2c_opal_translate_error(rc);
+		goto exit;
+	}
+
+	rc = opal_async_wait_response(token, &msg);
+	if (rc)
+		goto exit;
+
+	rc = be64_to_cpu(msg.params[1]);
+	if (rc != OPAL_SUCCESS) {
+		rc = i2c_opal_translate_error(rc);
+		goto exit;
+	}
+
+exit:
+	opal_async_release_token(token);
+	return rc;
+}
+
+static int i2c_opal_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
+				int num)
+{
+	unsigned long opal_id = (unsigned long)adap->algo_data;
+	struct opal_i2c_request req;
+	int rc, i;
+
+	/* We only support fairly simple combinations here of one
+	 * or two messages
+	 */
+	memset(&req, 0, sizeof(req));
+	switch(num) {
+	case 0:
+		return 0;
+	case 1:
+		req.type = (msgs[0].flags & I2C_M_RD) ?
+			OPAL_I2C_RAW_READ : OPAL_I2C_RAW_WRITE;
+		req.addr = cpu_to_be16(msgs[0].addr);
+		req.size = cpu_to_be32(msgs[0].len);
+		req.buffer_ra = cpu_to_be64(__pa(msgs[0].buf));
+		break;
+	case 2:
+		/* For two messages, we basically support only simple
+		 * smbus transactions of a write plus a read. We might
+		 * want to allow also two writes but we'd have to bounce
+		 * the data into a single buffer.
+		 */
+		if ((msgs[0].flags & I2C_M_RD) || !(msgs[1].flags & I2C_M_RD))
+			return -EOPNOTSUPP;
+		if (msgs[0].len > 4)
+			return -EOPNOTSUPP;
+		if (msgs[0].addr != msgs[1].addr)
+			return -EOPNOTSUPP;
+		req.type = OPAL_I2C_SM_READ;
+		req.addr = cpu_to_be16(msgs[0].addr);
+		req.subaddr_sz = msgs[0].len;
+		for (i = 0; i < msgs[0].len; i++)
+			req.subaddr = (req.subaddr << 8) | msgs[0].buf[i];
+		req.subaddr = cpu_to_be32(req.subaddr);
+		req.size = cpu_to_be32(msgs[1].len);
+		req.buffer_ra = cpu_to_be64(__pa(msgs[1].buf));
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	rc = i2c_opal_send_request(opal_id, &req);
+	if (rc)
+		return rc;
+
+	return num;
+}
+
+static int i2c_opal_smbus_xfer(struct i2c_adapter *adap, u16 addr,
+			       unsigned short flags, char read_write,
+			       u8 command, int size, union i2c_smbus_data *data)
+{
+	unsigned long opal_id = (unsigned long)adap->algo_data;
+	struct opal_i2c_request req;
+	u8 local[2];
+	int rc;
+
+	memset(&req, 0, sizeof(req));
+
+	req.addr = cpu_to_be16(addr);
+	switch (size) {
+	case I2C_SMBUS_BYTE:
+		req.buffer_ra = cpu_to_be64(__pa(&data->byte));
+		req.size = cpu_to_be32(1);
+		/* Fall through */
+	case I2C_SMBUS_QUICK:
+		req.type = (read_write == I2C_SMBUS_READ) ?
+			OPAL_I2C_RAW_READ : OPAL_I2C_RAW_WRITE;
+		break;
+	case I2C_SMBUS_BYTE_DATA:
+		req.buffer_ra = cpu_to_be64(__pa(&data->byte));
+		req.size = cpu_to_be32(1);
+		req.subaddr = cpu_to_be32(command);
+		req.subaddr_sz = 1;
+		req.type = (read_write == I2C_SMBUS_READ) ?
+			OPAL_I2C_SM_READ : OPAL_I2C_SM_WRITE;
+		break;
+	case I2C_SMBUS_WORD_DATA:
+		if (!read_write) {
+			local[0] = data->word & 0xff;
+			local[1] = (data->word >> 8) & 0xff;
+		}
+		req.buffer_ra = cpu_to_be64(__pa(local));
+		req.size = cpu_to_be32(2);
+		req.subaddr = cpu_to_be32(command);
+		req.subaddr_sz = 1;
+		req.type = (read_write == I2C_SMBUS_READ) ?
+			OPAL_I2C_SM_READ : OPAL_I2C_SM_WRITE;
+		break;
+	case I2C_SMBUS_I2C_BLOCK_DATA:
+		req.buffer_ra = cpu_to_be64(__pa(&data->block[1]));
+		req.size = cpu_to_be32(data->block[0]);
+		req.subaddr = cpu_to_be32(command);
+		req.subaddr_sz = 1;
+		req.type = (read_write == I2C_SMBUS_READ) ?
+			OPAL_I2C_SM_READ : OPAL_I2C_SM_WRITE;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	rc = i2c_opal_send_request(opal_id, &req);
+	if (!rc && read_write && size == I2C_SMBUS_WORD_DATA) {
+		data->word = ((u16)local[1]) << 8;
+		data->word |= local[0];
+	}
+
+	return rc;
+}
+
+static u32 i2c_opal_func(struct i2c_adapter *adapter)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE |
+	       I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA |
+	       I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static const struct i2c_algorithm i2c_opal_algo = {
+	.master_xfer	= i2c_opal_master_xfer,
+	.smbus_xfer	= i2c_opal_smbus_xfer,
+	.functionality	= i2c_opal_func,
+};
+
+static int i2c_opal_probe(struct platform_device *pdev)
+{
+	struct i2c_adapter	*adapter;
+	const char		*pname;
+	u32			opal_id;
+	int			rc;
+
+	if (!pdev->dev.of_node)
+		return -ENODEV;
+
+	rc = of_property_read_u32(pdev->dev.of_node, "ibm,opal-id", &opal_id);
+	if (rc) {
+		dev_err(&pdev->dev, "Missing ibm,opal-id property !\n");
+		return -EIO;
+	}
+
+	adapter = devm_kzalloc(&pdev->dev, sizeof(*adapter), GFP_KERNEL);
+	if (!adapter)
+		return -ENOMEM;
+
+	adapter->algo = &i2c_opal_algo;
+	adapter->algo_data = (void *)(unsigned long)opal_id;
+	adapter->dev.parent = &pdev->dev;
+	adapter->dev.of_node = of_node_get(pdev->dev.of_node);
+	pname = of_get_property(pdev->dev.of_node, "ibm,port-name", NULL);
+	if (pname)
+		strlcpy(adapter->name, pname, sizeof(adapter->name));
+	else
+		strlcpy(adapter->name, "opal", sizeof(adapter->name));
+
+	platform_set_drvdata(pdev, adapter);
+	rc = i2c_add_adapter(adapter);
+	if (rc)
+		dev_err(&pdev->dev, "Failed to register the i2c adapter\n");
+
+	return rc;
+}
+
+static int i2c_opal_remove(struct platform_device *pdev)
+{
+	struct i2c_adapter *adapter = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(adapter);
+
+	return 0;
+}
+
+static const struct of_device_id i2c_opal_of_match[] = {
+	{
+		.compatible = "ibm,opal-i2c",
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, i2c_opal_of_match);
+
+static struct platform_driver i2c_opal_driver = {
+	.probe	= i2c_opal_probe,
+	.remove	= i2c_opal_remove,
+	.driver	= {
+		.name		= "i2c-opal",
+		.of_match_table	= i2c_opal_of_match,
+	},
+};
+
+static int __init i2c_opal_init(void)
+{
+	if (!firmware_has_feature(FW_FEATURE_OPAL))
+		return -ENODEV;
+
+	return platform_driver_register(&i2c_opal_driver);
+}
+module_init(i2c_opal_init);
+
+static void __exit i2c_opal_exit(void)
+{
+	return platform_driver_unregister(&i2c_opal_driver);
+}
+module_exit(i2c_opal_exit);
+
+MODULE_AUTHOR("Neelesh Gupta <neelegup@linux.vnet.ibm.com>");
+MODULE_DESCRIPTION("IBM OPAL I2C driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/misc/cxl/context.c b/drivers/misc/cxl/context.c
index cca4721..51fd6b5 100644
--- a/drivers/misc/cxl/context.c
+++ b/drivers/misc/cxl/context.c
@@ -34,7 +34,8 @@
 /*
  * Initialises a CXL context.
  */
-int cxl_context_init(struct cxl_context *ctx, struct cxl_afu *afu, bool master)
+int cxl_context_init(struct cxl_context *ctx, struct cxl_afu *afu, bool master,
+		     struct address_space *mapping)
 {
 	int i;
 
@@ -42,6 +43,8 @@
 	ctx->afu = afu;
 	ctx->master = master;
 	ctx->pid = NULL; /* Set in start work ioctl */
+	mutex_init(&ctx->mapping_lock);
+	ctx->mapping = mapping;
 
 	/*
 	 * Allocate the segment table before we put it in the IDR so that we
@@ -82,12 +85,12 @@
 	 * Allocating IDR! We better make sure everything's setup that
 	 * dereferences from it.
 	 */
+	mutex_lock(&afu->contexts_lock);
 	idr_preload(GFP_KERNEL);
-	spin_lock(&afu->contexts_lock);
 	i = idr_alloc(&ctx->afu->contexts_idr, ctx, 0,
 		      ctx->afu->num_procs, GFP_NOWAIT);
-	spin_unlock(&afu->contexts_lock);
 	idr_preload_end();
+	mutex_unlock(&afu->contexts_lock);
 	if (i < 0)
 		return i;
 
@@ -147,6 +150,12 @@
 	afu_release_irqs(ctx);
 	flush_work(&ctx->fault_work); /* Only needed for dedicated process */
 	wake_up_all(&ctx->wq);
+
+	/* Release Problem State Area mapping */
+	mutex_lock(&ctx->mapping_lock);
+	if (ctx->mapping)
+		unmap_mapping_range(ctx->mapping, 0, 0, 1);
+	mutex_unlock(&ctx->mapping_lock);
 }
 
 /*
@@ -168,21 +177,22 @@
 	struct cxl_context *ctx;
 	int tmp;
 
-	rcu_read_lock();
-	idr_for_each_entry(&afu->contexts_idr, ctx, tmp)
+	mutex_lock(&afu->contexts_lock);
+	idr_for_each_entry(&afu->contexts_idr, ctx, tmp) {
 		/*
 		 * Anything done in here needs to be setup before the IDR is
 		 * created and torn down after the IDR removed
 		 */
 		__detach_context(ctx);
-	rcu_read_unlock();
+	}
+	mutex_unlock(&afu->contexts_lock);
 }
 
 void cxl_context_free(struct cxl_context *ctx)
 {
-	spin_lock(&ctx->afu->contexts_lock);
+	mutex_lock(&ctx->afu->contexts_lock);
 	idr_remove(&ctx->afu->contexts_idr, ctx->pe);
-	spin_unlock(&ctx->afu->contexts_lock);
+	mutex_unlock(&ctx->afu->contexts_lock);
 	synchronize_rcu();
 
 	free_page((u64)ctx->sstp);
diff --git a/drivers/misc/cxl/cxl.h b/drivers/misc/cxl/cxl.h
index b5b6bda..28078f8 100644
--- a/drivers/misc/cxl/cxl.h
+++ b/drivers/misc/cxl/cxl.h
@@ -351,7 +351,7 @@
 	struct device *chardev_s, *chardev_m, *chardev_d;
 	struct idr contexts_idr;
 	struct dentry *debugfs;
-	spinlock_t contexts_lock;
+	struct mutex contexts_lock;
 	struct mutex spa_mutex;
 	spinlock_t afu_cntl_lock;
 
@@ -398,6 +398,10 @@
 	phys_addr_t psn_phys;
 	u64 psn_size;
 
+	/* Used to unmap any mmaps when force detaching */
+	struct address_space *mapping;
+	struct mutex mapping_lock;
+
 	spinlock_t sste_lock; /* Protects segment table entries */
 	struct cxl_sste *sstp;
 	u64 sstp0, sstp1;
@@ -599,7 +603,8 @@
 void init_cxl_native(void);
 
 struct cxl_context *cxl_context_alloc(void);
-int cxl_context_init(struct cxl_context *ctx, struct cxl_afu *afu, bool master);
+int cxl_context_init(struct cxl_context *ctx, struct cxl_afu *afu, bool master,
+		     struct address_space *mapping);
 void cxl_context_free(struct cxl_context *ctx);
 int cxl_context_iomap(struct cxl_context *ctx, struct vm_area_struct *vma);
 
diff --git a/drivers/misc/cxl/file.c b/drivers/misc/cxl/file.c
index 378b099..e9f2f10 100644
--- a/drivers/misc/cxl/file.c
+++ b/drivers/misc/cxl/file.c
@@ -77,7 +77,7 @@
 		goto err_put_afu;
 	}
 
-	if ((rc = cxl_context_init(ctx, afu, master)))
+	if ((rc = cxl_context_init(ctx, afu, master, inode->i_mapping)))
 		goto err_put_afu;
 
 	pr_devel("afu_open pe: %i\n", ctx->pe);
@@ -113,6 +113,10 @@
 		 __func__, ctx->pe);
 	cxl_context_detach(ctx);
 
+	mutex_lock(&ctx->mapping_lock);
+	ctx->mapping = NULL;
+	mutex_unlock(&ctx->mapping_lock);
+
 	put_device(&ctx->afu->dev);
 
 	/*
diff --git a/drivers/misc/cxl/native.c b/drivers/misc/cxl/native.c
index 9a5a442..f2b37b4 100644
--- a/drivers/misc/cxl/native.c
+++ b/drivers/misc/cxl/native.c
@@ -277,6 +277,7 @@
 				  u64 cmd, u64 pe_state)
 {
 	u64 state;
+	unsigned long timeout = jiffies + (HZ * CXL_TIMEOUT);
 
 	WARN_ON(!ctx->afu->enabled);
 
@@ -286,6 +287,10 @@
 	smp_mb();
 	cxl_p1n_write(ctx->afu, CXL_PSL_LLCMD_An, cmd | ctx->pe);
 	while (1) {
+		if (time_after_eq(jiffies, timeout)) {
+			dev_warn(&ctx->afu->dev, "WARNING: Process Element Command timed out!\n");
+			return -EBUSY;
+		}
 		state = be64_to_cpup(ctx->afu->sw_command_status);
 		if (state == ~0ULL) {
 			pr_err("cxl: Error adding process element to AFU\n");
@@ -610,13 +615,6 @@
 	return 0;
 }
 
-/*
- * TODO: handle case when this is called inside a rcu_read_lock() which may
- * happen when we unbind the driver (ie. cxl_context_detach_all()) .  Terminate
- * & remove use a mutex lock and schedule which will not good with lock held.
- * May need to write do_process_element_cmd() that handles outstanding page
- * faults synchronously.
- */
 static inline int detach_process_native_afu_directed(struct cxl_context *ctx)
 {
 	if (!ctx->pe_inserted)
diff --git a/drivers/misc/cxl/pci.c b/drivers/misc/cxl/pci.c
index 10c98ab..0f2cc9f8 100644
--- a/drivers/misc/cxl/pci.c
+++ b/drivers/misc/cxl/pci.c
@@ -502,7 +502,7 @@
 	afu->dev.release = cxl_release_afu;
 	afu->slice = slice;
 	idr_init(&afu->contexts_idr);
-	spin_lock_init(&afu->contexts_lock);
+	mutex_init(&afu->contexts_lock);
 	spin_lock_init(&afu->afu_cntl_lock);
 	mutex_init(&afu->spa_mutex);
 
diff --git a/drivers/misc/cxl/sysfs.c b/drivers/misc/cxl/sysfs.c
index ce7ec06..461bdbd 100644
--- a/drivers/misc/cxl/sysfs.c
+++ b/drivers/misc/cxl/sysfs.c
@@ -121,7 +121,7 @@
 	int rc;
 
 	/* Not safe to reset if it is currently in use */
-	spin_lock(&afu->contexts_lock);
+	mutex_lock(&afu->contexts_lock);
 	if (!idr_is_empty(&afu->contexts_idr)) {
 		rc = -EBUSY;
 		goto err;
@@ -132,7 +132,7 @@
 
 	rc = count;
 err:
-	spin_unlock(&afu->contexts_lock);
+	mutex_unlock(&afu->contexts_lock);
 	return rc;
 }
 
@@ -247,7 +247,7 @@
 	int rc = -EBUSY;
 
 	/* can't change this if we have a user */
-	spin_lock(&afu->contexts_lock);
+	mutex_lock(&afu->contexts_lock);
 	if (!idr_is_empty(&afu->contexts_idr))
 		goto err;
 
@@ -271,7 +271,7 @@
 	afu->current_mode = 0;
 	afu->num_procs = 0;
 
-	spin_unlock(&afu->contexts_lock);
+	mutex_unlock(&afu->contexts_lock);
 
 	if ((rc = _cxl_afu_deactivate_mode(afu, old_mode)))
 		return rc;
@@ -280,7 +280,7 @@
 
 	return count;
 err:
-	spin_unlock(&afu->contexts_lock);
+	mutex_unlock(&afu->contexts_lock);
 	return rc;
 }
 
diff --git a/include/uapi/linux/audit.h b/include/uapi/linux/audit.h
index 12e2668..d3475e1 100644
--- a/include/uapi/linux/audit.h
+++ b/include/uapi/linux/audit.h
@@ -371,7 +371,9 @@
 #define AUDIT_ARCH_PARISC	(EM_PARISC)
 #define AUDIT_ARCH_PARISC64	(EM_PARISC|__AUDIT_ARCH_64BIT)
 #define AUDIT_ARCH_PPC		(EM_PPC)
+/* do not define AUDIT_ARCH_PPCLE since it is not supported by audit */
 #define AUDIT_ARCH_PPC64	(EM_PPC64|__AUDIT_ARCH_64BIT)
+#define AUDIT_ARCH_PPC64LE	(EM_PPC64|__AUDIT_ARCH_64BIT|__AUDIT_ARCH_LE)
 #define AUDIT_ARCH_S390		(EM_S390)
 #define AUDIT_ARCH_S390X	(EM_S390|__AUDIT_ARCH_64BIT)
 #define AUDIT_ARCH_SH		(EM_SH)