| /* |
| * Power Management Service Unit(PMSU) support for Armada 370/XP platforms. |
| * |
| * Copyright (C) 2012 Marvell |
| * |
| * Yehuda Yitschak <yehuday@marvell.com> |
| * Gregory Clement <gregory.clement@free-electrons.com> |
| * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> |
| * |
| * This file is licensed under the terms of the GNU General Public |
| * License version 2. This program is licensed "as is" without any |
| * warranty of any kind, whether express or implied. |
| * |
| * The Armada 370 and Armada XP SOCs have a power management service |
| * unit which is responsible for powering down and waking up CPUs and |
| * other SOC units |
| */ |
| |
| #define pr_fmt(fmt) "mvebu-pmsu: " fmt |
| |
| #include <linux/clk.h> |
| #include <linux/cpu_pm.h> |
| #include <linux/cpufreq-dt.h> |
| #include <linux/delay.h> |
| #include <linux/init.h> |
| #include <linux/io.h> |
| #include <linux/kernel.h> |
| #include <linux/mbus.h> |
| #include <linux/of_address.h> |
| #include <linux/of_device.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_opp.h> |
| #include <linux/resource.h> |
| #include <linux/slab.h> |
| #include <linux/smp.h> |
| #include <asm/cacheflush.h> |
| #include <asm/cp15.h> |
| #include <asm/smp_scu.h> |
| #include <asm/smp_plat.h> |
| #include <asm/suspend.h> |
| #include <asm/tlbflush.h> |
| #include "common.h" |
| |
| |
| #define PMSU_BASE_OFFSET 0x100 |
| #define PMSU_REG_SIZE 0x1000 |
| |
| /* PMSU MP registers */ |
| #define PMSU_CONTROL_AND_CONFIG(cpu) ((cpu * 0x100) + 0x104) |
| #define PMSU_CONTROL_AND_CONFIG_DFS_REQ BIT(18) |
| #define PMSU_CONTROL_AND_CONFIG_PWDDN_REQ BIT(16) |
| #define PMSU_CONTROL_AND_CONFIG_L2_PWDDN BIT(20) |
| |
| #define PMSU_CPU_POWER_DOWN_CONTROL(cpu) ((cpu * 0x100) + 0x108) |
| |
| #define PMSU_CPU_POWER_DOWN_DIS_SNP_Q_SKIP BIT(0) |
| |
| #define PMSU_STATUS_AND_MASK(cpu) ((cpu * 0x100) + 0x10c) |
| #define PMSU_STATUS_AND_MASK_CPU_IDLE_WAIT BIT(16) |
| #define PMSU_STATUS_AND_MASK_SNP_Q_EMPTY_WAIT BIT(17) |
| #define PMSU_STATUS_AND_MASK_IRQ_WAKEUP BIT(20) |
| #define PMSU_STATUS_AND_MASK_FIQ_WAKEUP BIT(21) |
| #define PMSU_STATUS_AND_MASK_DBG_WAKEUP BIT(22) |
| #define PMSU_STATUS_AND_MASK_IRQ_MASK BIT(24) |
| #define PMSU_STATUS_AND_MASK_FIQ_MASK BIT(25) |
| |
| #define PMSU_EVENT_STATUS_AND_MASK(cpu) ((cpu * 0x100) + 0x120) |
| #define PMSU_EVENT_STATUS_AND_MASK_DFS_DONE BIT(1) |
| #define PMSU_EVENT_STATUS_AND_MASK_DFS_DONE_MASK BIT(17) |
| |
| #define PMSU_BOOT_ADDR_REDIRECT_OFFSET(cpu) ((cpu * 0x100) + 0x124) |
| |
| /* PMSU fabric registers */ |
| #define L2C_NFABRIC_PM_CTL 0x4 |
| #define L2C_NFABRIC_PM_CTL_PWR_DOWN BIT(20) |
| |
| /* PMSU delay registers */ |
| #define PMSU_POWERDOWN_DELAY 0xF04 |
| #define PMSU_POWERDOWN_DELAY_PMU BIT(1) |
| #define PMSU_POWERDOWN_DELAY_MASK 0xFFFE |
| #define PMSU_DFLT_ARMADA38X_DELAY 0x64 |
| |
| /* CA9 MPcore SoC Control registers */ |
| |
| #define MPCORE_RESET_CTL 0x64 |
| #define MPCORE_RESET_CTL_L2 BIT(0) |
| #define MPCORE_RESET_CTL_DEBUG BIT(16) |
| |
| #define SRAM_PHYS_BASE 0xFFFF0000 |
| #define BOOTROM_BASE 0xFFF00000 |
| #define BOOTROM_SIZE 0x100000 |
| |
| #define ARMADA_370_CRYPT0_ENG_TARGET 0x9 |
| #define ARMADA_370_CRYPT0_ENG_ATTR 0x1 |
| |
| extern void ll_disable_coherency(void); |
| extern void ll_enable_coherency(void); |
| |
| extern void armada_370_xp_cpu_resume(void); |
| extern void armada_38x_cpu_resume(void); |
| |
| static phys_addr_t pmsu_mp_phys_base; |
| static void __iomem *pmsu_mp_base; |
| |
| static void *mvebu_cpu_resume; |
| |
| static const struct of_device_id of_pmsu_table[] = { |
| { .compatible = "marvell,armada-370-pmsu", }, |
| { .compatible = "marvell,armada-370-xp-pmsu", }, |
| { .compatible = "marvell,armada-380-pmsu", }, |
| { /* end of list */ }, |
| }; |
| |
| void mvebu_pmsu_set_cpu_boot_addr(int hw_cpu, void *boot_addr) |
| { |
| writel(virt_to_phys(boot_addr), pmsu_mp_base + |
| PMSU_BOOT_ADDR_REDIRECT_OFFSET(hw_cpu)); |
| } |
| |
| extern unsigned char mvebu_boot_wa_start; |
| extern unsigned char mvebu_boot_wa_end; |
| |
| /* |
| * This function sets up the boot address workaround needed for SMP |
| * boot on Armada 375 Z1 and cpuidle on Armada 370. It unmaps the |
| * BootROM Mbus window, and instead remaps a crypto SRAM into which a |
| * custom piece of code is copied to replace the problematic BootROM. |
| */ |
| int mvebu_setup_boot_addr_wa(unsigned int crypto_eng_target, |
| unsigned int crypto_eng_attribute, |
| phys_addr_t resume_addr_reg) |
| { |
| void __iomem *sram_virt_base; |
| u32 code_len = &mvebu_boot_wa_end - &mvebu_boot_wa_start; |
| |
| mvebu_mbus_del_window(BOOTROM_BASE, BOOTROM_SIZE); |
| mvebu_mbus_add_window_by_id(crypto_eng_target, crypto_eng_attribute, |
| SRAM_PHYS_BASE, SZ_64K); |
| |
| sram_virt_base = ioremap(SRAM_PHYS_BASE, SZ_64K); |
| if (!sram_virt_base) { |
| pr_err("Unable to map SRAM to setup the boot address WA\n"); |
| return -ENOMEM; |
| } |
| |
| memcpy(sram_virt_base, &mvebu_boot_wa_start, code_len); |
| |
| /* |
| * The last word of the code copied in SRAM must contain the |
| * physical base address of the PMSU register. We |
| * intentionally store this address in the native endianness |
| * of the system. |
| */ |
| __raw_writel((unsigned long)resume_addr_reg, |
| sram_virt_base + code_len - 4); |
| |
| iounmap(sram_virt_base); |
| |
| return 0; |
| } |
| |
| static int __init mvebu_v7_pmsu_init(void) |
| { |
| struct device_node *np; |
| struct resource res; |
| int ret = 0; |
| |
| np = of_find_matching_node(NULL, of_pmsu_table); |
| if (!np) |
| return 0; |
| |
| pr_info("Initializing Power Management Service Unit\n"); |
| |
| if (of_address_to_resource(np, 0, &res)) { |
| pr_err("unable to get resource\n"); |
| ret = -ENOENT; |
| goto out; |
| } |
| |
| if (of_device_is_compatible(np, "marvell,armada-370-xp-pmsu")) { |
| pr_warn(FW_WARN "deprecated pmsu binding\n"); |
| res.start = res.start - PMSU_BASE_OFFSET; |
| res.end = res.start + PMSU_REG_SIZE - 1; |
| } |
| |
| if (!request_mem_region(res.start, resource_size(&res), |
| np->full_name)) { |
| pr_err("unable to request region\n"); |
| ret = -EBUSY; |
| goto out; |
| } |
| |
| pmsu_mp_phys_base = res.start; |
| |
| pmsu_mp_base = ioremap(res.start, resource_size(&res)); |
| if (!pmsu_mp_base) { |
| pr_err("unable to map registers\n"); |
| release_mem_region(res.start, resource_size(&res)); |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| out: |
| of_node_put(np); |
| return ret; |
| } |
| |
| static void mvebu_v7_pmsu_enable_l2_powerdown_onidle(void) |
| { |
| u32 reg; |
| |
| if (pmsu_mp_base == NULL) |
| return; |
| |
| /* Enable L2 & Fabric powerdown in Deep-Idle mode - Fabric */ |
| reg = readl(pmsu_mp_base + L2C_NFABRIC_PM_CTL); |
| reg |= L2C_NFABRIC_PM_CTL_PWR_DOWN; |
| writel(reg, pmsu_mp_base + L2C_NFABRIC_PM_CTL); |
| } |
| |
| enum pmsu_idle_prepare_flags { |
| PMSU_PREPARE_NORMAL = 0, |
| PMSU_PREPARE_DEEP_IDLE = BIT(0), |
| PMSU_PREPARE_SNOOP_DISABLE = BIT(1), |
| }; |
| |
| /* No locking is needed because we only access per-CPU registers */ |
| static int mvebu_v7_pmsu_idle_prepare(unsigned long flags) |
| { |
| unsigned int hw_cpu = cpu_logical_map(smp_processor_id()); |
| u32 reg; |
| |
| if (pmsu_mp_base == NULL) |
| return -EINVAL; |
| |
| /* |
| * Adjust the PMSU configuration to wait for WFI signal, enable |
| * IRQ and FIQ as wakeup events, set wait for snoop queue empty |
| * indication and mask IRQ and FIQ from CPU |
| */ |
| reg = readl(pmsu_mp_base + PMSU_STATUS_AND_MASK(hw_cpu)); |
| reg |= PMSU_STATUS_AND_MASK_CPU_IDLE_WAIT | |
| PMSU_STATUS_AND_MASK_IRQ_WAKEUP | |
| PMSU_STATUS_AND_MASK_FIQ_WAKEUP | |
| PMSU_STATUS_AND_MASK_SNP_Q_EMPTY_WAIT | |
| PMSU_STATUS_AND_MASK_IRQ_MASK | |
| PMSU_STATUS_AND_MASK_FIQ_MASK; |
| writel(reg, pmsu_mp_base + PMSU_STATUS_AND_MASK(hw_cpu)); |
| |
| reg = readl(pmsu_mp_base + PMSU_CONTROL_AND_CONFIG(hw_cpu)); |
| /* ask HW to power down the L2 Cache if needed */ |
| if (flags & PMSU_PREPARE_DEEP_IDLE) |
| reg |= PMSU_CONTROL_AND_CONFIG_L2_PWDDN; |
| |
| /* request power down */ |
| reg |= PMSU_CONTROL_AND_CONFIG_PWDDN_REQ; |
| writel(reg, pmsu_mp_base + PMSU_CONTROL_AND_CONFIG(hw_cpu)); |
| |
| if (flags & PMSU_PREPARE_SNOOP_DISABLE) { |
| /* Disable snoop disable by HW - SW is taking care of it */ |
| reg = readl(pmsu_mp_base + PMSU_CPU_POWER_DOWN_CONTROL(hw_cpu)); |
| reg |= PMSU_CPU_POWER_DOWN_DIS_SNP_Q_SKIP; |
| writel(reg, pmsu_mp_base + PMSU_CPU_POWER_DOWN_CONTROL(hw_cpu)); |
| } |
| |
| return 0; |
| } |
| |
| int armada_370_xp_pmsu_idle_enter(unsigned long deepidle) |
| { |
| unsigned long flags = PMSU_PREPARE_SNOOP_DISABLE; |
| int ret; |
| |
| if (deepidle) |
| flags |= PMSU_PREPARE_DEEP_IDLE; |
| |
| ret = mvebu_v7_pmsu_idle_prepare(flags); |
| if (ret) |
| return ret; |
| |
| v7_exit_coherency_flush(all); |
| |
| ll_disable_coherency(); |
| |
| dsb(); |
| |
| wfi(); |
| |
| /* If we are here, wfi failed. As processors run out of |
| * coherency for some time, tlbs might be stale, so flush them |
| */ |
| local_flush_tlb_all(); |
| |
| ll_enable_coherency(); |
| |
| /* Test the CR_C bit and set it if it was cleared */ |
| asm volatile( |
| "mrc p15, 0, r0, c1, c0, 0 \n\t" |
| "tst r0, #(1 << 2) \n\t" |
| "orreq r0, r0, #(1 << 2) \n\t" |
| "mcreq p15, 0, r0, c1, c0, 0 \n\t" |
| "isb " |
| : : : "r0"); |
| |
| pr_debug("Failed to suspend the system\n"); |
| |
| return 0; |
| } |
| |
| static int armada_370_xp_cpu_suspend(unsigned long deepidle) |
| { |
| return cpu_suspend(deepidle, armada_370_xp_pmsu_idle_enter); |
| } |
| |
| int armada_38x_do_cpu_suspend(unsigned long deepidle) |
| { |
| unsigned long flags = 0; |
| |
| if (deepidle) |
| flags |= PMSU_PREPARE_DEEP_IDLE; |
| |
| mvebu_v7_pmsu_idle_prepare(flags); |
| /* |
| * Already flushed cache, but do it again as the outer cache |
| * functions dirty the cache with spinlocks |
| */ |
| v7_exit_coherency_flush(louis); |
| |
| scu_power_mode(mvebu_get_scu_base(), SCU_PM_POWEROFF); |
| |
| cpu_do_idle(); |
| |
| return 1; |
| } |
| |
| static int armada_38x_cpu_suspend(unsigned long deepidle) |
| { |
| return cpu_suspend(false, armada_38x_do_cpu_suspend); |
| } |
| |
| /* No locking is needed because we only access per-CPU registers */ |
| void mvebu_v7_pmsu_idle_exit(void) |
| { |
| unsigned int hw_cpu = cpu_logical_map(smp_processor_id()); |
| u32 reg; |
| |
| if (pmsu_mp_base == NULL) |
| return; |
| /* cancel ask HW to power down the L2 Cache if possible */ |
| reg = readl(pmsu_mp_base + PMSU_CONTROL_AND_CONFIG(hw_cpu)); |
| reg &= ~PMSU_CONTROL_AND_CONFIG_L2_PWDDN; |
| writel(reg, pmsu_mp_base + PMSU_CONTROL_AND_CONFIG(hw_cpu)); |
| |
| /* cancel Enable wakeup events and mask interrupts */ |
| reg = readl(pmsu_mp_base + PMSU_STATUS_AND_MASK(hw_cpu)); |
| reg &= ~(PMSU_STATUS_AND_MASK_IRQ_WAKEUP | PMSU_STATUS_AND_MASK_FIQ_WAKEUP); |
| reg &= ~PMSU_STATUS_AND_MASK_CPU_IDLE_WAIT; |
| reg &= ~PMSU_STATUS_AND_MASK_SNP_Q_EMPTY_WAIT; |
| reg &= ~(PMSU_STATUS_AND_MASK_IRQ_MASK | PMSU_STATUS_AND_MASK_FIQ_MASK); |
| writel(reg, pmsu_mp_base + PMSU_STATUS_AND_MASK(hw_cpu)); |
| } |
| |
| static int mvebu_v7_cpu_pm_notify(struct notifier_block *self, |
| unsigned long action, void *hcpu) |
| { |
| if (action == CPU_PM_ENTER) { |
| unsigned int hw_cpu = cpu_logical_map(smp_processor_id()); |
| mvebu_pmsu_set_cpu_boot_addr(hw_cpu, mvebu_cpu_resume); |
| } else if (action == CPU_PM_EXIT) { |
| mvebu_v7_pmsu_idle_exit(); |
| } |
| |
| return NOTIFY_OK; |
| } |
| |
| static struct notifier_block mvebu_v7_cpu_pm_notifier = { |
| .notifier_call = mvebu_v7_cpu_pm_notify, |
| }; |
| |
| static struct platform_device mvebu_v7_cpuidle_device; |
| |
| static __init int armada_370_cpuidle_init(void) |
| { |
| struct device_node *np; |
| phys_addr_t redirect_reg; |
| |
| np = of_find_compatible_node(NULL, NULL, "marvell,coherency-fabric"); |
| if (!np) |
| return -ENODEV; |
| of_node_put(np); |
| |
| /* |
| * On Armada 370, there is "a slow exit process from the deep |
| * idle state due to heavy L1/L2 cache cleanup operations |
| * performed by the BootROM software". To avoid this, we |
| * replace the restart code of the bootrom by a a simple jump |
| * to the boot address. Then the code located at this boot |
| * address will take care of the initialization. |
| */ |
| redirect_reg = pmsu_mp_phys_base + PMSU_BOOT_ADDR_REDIRECT_OFFSET(0); |
| mvebu_setup_boot_addr_wa(ARMADA_370_CRYPT0_ENG_TARGET, |
| ARMADA_370_CRYPT0_ENG_ATTR, |
| redirect_reg); |
| |
| mvebu_cpu_resume = armada_370_xp_cpu_resume; |
| mvebu_v7_cpuidle_device.dev.platform_data = armada_370_xp_cpu_suspend; |
| mvebu_v7_cpuidle_device.name = "cpuidle-armada-370"; |
| |
| return 0; |
| } |
| |
| static __init int armada_38x_cpuidle_init(void) |
| { |
| struct device_node *np; |
| void __iomem *mpsoc_base; |
| u32 reg; |
| |
| pr_warn("CPU idle is currently broken on Armada 38x: disabling\n"); |
| return 0; |
| |
| np = of_find_compatible_node(NULL, NULL, |
| "marvell,armada-380-coherency-fabric"); |
| if (!np) |
| return -ENODEV; |
| of_node_put(np); |
| |
| np = of_find_compatible_node(NULL, NULL, |
| "marvell,armada-380-mpcore-soc-ctrl"); |
| if (!np) |
| return -ENODEV; |
| mpsoc_base = of_iomap(np, 0); |
| BUG_ON(!mpsoc_base); |
| of_node_put(np); |
| |
| /* Set up reset mask when powering down the cpus */ |
| reg = readl(mpsoc_base + MPCORE_RESET_CTL); |
| reg |= MPCORE_RESET_CTL_L2; |
| reg |= MPCORE_RESET_CTL_DEBUG; |
| writel(reg, mpsoc_base + MPCORE_RESET_CTL); |
| iounmap(mpsoc_base); |
| |
| /* Set up delay */ |
| reg = readl(pmsu_mp_base + PMSU_POWERDOWN_DELAY); |
| reg &= ~PMSU_POWERDOWN_DELAY_MASK; |
| reg |= PMSU_DFLT_ARMADA38X_DELAY; |
| reg |= PMSU_POWERDOWN_DELAY_PMU; |
| writel(reg, pmsu_mp_base + PMSU_POWERDOWN_DELAY); |
| |
| mvebu_cpu_resume = armada_38x_cpu_resume; |
| mvebu_v7_cpuidle_device.dev.platform_data = armada_38x_cpu_suspend; |
| mvebu_v7_cpuidle_device.name = "cpuidle-armada-38x"; |
| |
| return 0; |
| } |
| |
| static __init int armada_xp_cpuidle_init(void) |
| { |
| struct device_node *np; |
| |
| np = of_find_compatible_node(NULL, NULL, "marvell,coherency-fabric"); |
| if (!np) |
| return -ENODEV; |
| of_node_put(np); |
| |
| mvebu_cpu_resume = armada_370_xp_cpu_resume; |
| mvebu_v7_cpuidle_device.dev.platform_data = armada_370_xp_cpu_suspend; |
| mvebu_v7_cpuidle_device.name = "cpuidle-armada-xp"; |
| |
| return 0; |
| } |
| |
| static int __init mvebu_v7_cpu_pm_init(void) |
| { |
| struct device_node *np; |
| int ret; |
| |
| np = of_find_matching_node(NULL, of_pmsu_table); |
| if (!np) |
| return 0; |
| of_node_put(np); |
| |
| /* |
| * Currently the CPU idle support for Armada 38x is broken, as |
| * the CPU hotplug uses some of the CPU idle functions it is |
| * broken too, so let's disable it |
| */ |
| if (of_machine_is_compatible("marvell,armada380")) { |
| cpu_hotplug_disable(); |
| pr_warn("CPU hotplug support is currently broken on Armada 38x: disabling\n"); |
| } |
| |
| if (of_machine_is_compatible("marvell,armadaxp")) |
| ret = armada_xp_cpuidle_init(); |
| else if (of_machine_is_compatible("marvell,armada370")) |
| ret = armada_370_cpuidle_init(); |
| else if (of_machine_is_compatible("marvell,armada380")) |
| ret = armada_38x_cpuidle_init(); |
| else |
| return 0; |
| |
| if (ret) |
| return ret; |
| |
| mvebu_v7_pmsu_enable_l2_powerdown_onidle(); |
| if (mvebu_v7_cpuidle_device.name) |
| platform_device_register(&mvebu_v7_cpuidle_device); |
| cpu_pm_register_notifier(&mvebu_v7_cpu_pm_notifier); |
| |
| return 0; |
| } |
| |
| arch_initcall(mvebu_v7_cpu_pm_init); |
| early_initcall(mvebu_v7_pmsu_init); |
| |
| static void mvebu_pmsu_dfs_request_local(void *data) |
| { |
| u32 reg; |
| u32 cpu = smp_processor_id(); |
| unsigned long flags; |
| |
| local_irq_save(flags); |
| |
| /* Prepare to enter idle */ |
| reg = readl(pmsu_mp_base + PMSU_STATUS_AND_MASK(cpu)); |
| reg |= PMSU_STATUS_AND_MASK_CPU_IDLE_WAIT | |
| PMSU_STATUS_AND_MASK_IRQ_MASK | |
| PMSU_STATUS_AND_MASK_FIQ_MASK; |
| writel(reg, pmsu_mp_base + PMSU_STATUS_AND_MASK(cpu)); |
| |
| /* Request the DFS transition */ |
| reg = readl(pmsu_mp_base + PMSU_CONTROL_AND_CONFIG(cpu)); |
| reg |= PMSU_CONTROL_AND_CONFIG_DFS_REQ; |
| writel(reg, pmsu_mp_base + PMSU_CONTROL_AND_CONFIG(cpu)); |
| |
| /* The fact of entering idle will trigger the DFS transition */ |
| wfi(); |
| |
| /* |
| * We're back from idle, the DFS transition has completed, |
| * clear the idle wait indication. |
| */ |
| reg = readl(pmsu_mp_base + PMSU_STATUS_AND_MASK(cpu)); |
| reg &= ~PMSU_STATUS_AND_MASK_CPU_IDLE_WAIT; |
| writel(reg, pmsu_mp_base + PMSU_STATUS_AND_MASK(cpu)); |
| |
| local_irq_restore(flags); |
| } |
| |
| int mvebu_pmsu_dfs_request(int cpu) |
| { |
| unsigned long timeout; |
| int hwcpu = cpu_logical_map(cpu); |
| u32 reg; |
| |
| /* Clear any previous DFS DONE event */ |
| reg = readl(pmsu_mp_base + PMSU_EVENT_STATUS_AND_MASK(hwcpu)); |
| reg &= ~PMSU_EVENT_STATUS_AND_MASK_DFS_DONE; |
| writel(reg, pmsu_mp_base + PMSU_EVENT_STATUS_AND_MASK(hwcpu)); |
| |
| /* Mask the DFS done interrupt, since we are going to poll */ |
| reg = readl(pmsu_mp_base + PMSU_EVENT_STATUS_AND_MASK(hwcpu)); |
| reg |= PMSU_EVENT_STATUS_AND_MASK_DFS_DONE_MASK; |
| writel(reg, pmsu_mp_base + PMSU_EVENT_STATUS_AND_MASK(hwcpu)); |
| |
| /* Trigger the DFS on the appropriate CPU */ |
| smp_call_function_single(cpu, mvebu_pmsu_dfs_request_local, |
| NULL, false); |
| |
| /* Poll until the DFS done event is generated */ |
| timeout = jiffies + HZ; |
| while (time_before(jiffies, timeout)) { |
| reg = readl(pmsu_mp_base + PMSU_EVENT_STATUS_AND_MASK(hwcpu)); |
| if (reg & PMSU_EVENT_STATUS_AND_MASK_DFS_DONE) |
| break; |
| udelay(10); |
| } |
| |
| if (time_after(jiffies, timeout)) |
| return -ETIME; |
| |
| /* Restore the DFS mask to its original state */ |
| reg = readl(pmsu_mp_base + PMSU_EVENT_STATUS_AND_MASK(hwcpu)); |
| reg &= ~PMSU_EVENT_STATUS_AND_MASK_DFS_DONE_MASK; |
| writel(reg, pmsu_mp_base + PMSU_EVENT_STATUS_AND_MASK(hwcpu)); |
| |
| return 0; |
| } |
| |
| struct cpufreq_dt_platform_data cpufreq_dt_pd = { |
| .independent_clocks = true, |
| }; |
| |
| static int __init armada_xp_pmsu_cpufreq_init(void) |
| { |
| struct device_node *np; |
| struct resource res; |
| int ret, cpu; |
| |
| if (!of_machine_is_compatible("marvell,armadaxp")) |
| return 0; |
| |
| /* |
| * In order to have proper cpufreq handling, we need to ensure |
| * that the Device Tree description of the CPU clock includes |
| * the definition of the PMU DFS registers. If not, we do not |
| * register the clock notifier and the cpufreq driver. This |
| * piece of code is only for compatibility with old Device |
| * Trees. |
| */ |
| np = of_find_compatible_node(NULL, NULL, "marvell,armada-xp-cpu-clock"); |
| if (!np) |
| return 0; |
| |
| ret = of_address_to_resource(np, 1, &res); |
| if (ret) { |
| pr_warn(FW_WARN "not enabling cpufreq, deprecated armada-xp-cpu-clock binding\n"); |
| of_node_put(np); |
| return 0; |
| } |
| |
| of_node_put(np); |
| |
| /* |
| * For each CPU, this loop registers the operating points |
| * supported (which are the nominal CPU frequency and half of |
| * it), and registers the clock notifier that will take care |
| * of doing the PMSU part of a frequency transition. |
| */ |
| for_each_possible_cpu(cpu) { |
| struct device *cpu_dev; |
| struct clk *clk; |
| int ret; |
| |
| cpu_dev = get_cpu_device(cpu); |
| if (!cpu_dev) { |
| pr_err("Cannot get CPU %d\n", cpu); |
| continue; |
| } |
| |
| clk = clk_get(cpu_dev, 0); |
| if (IS_ERR(clk)) { |
| pr_err("Cannot get clock for CPU %d\n", cpu); |
| return PTR_ERR(clk); |
| } |
| |
| /* |
| * In case of a failure of dev_pm_opp_add(), we don't |
| * bother with cleaning up the registered OPP (there's |
| * no function to do so), and simply cancel the |
| * registration of the cpufreq device. |
| */ |
| ret = dev_pm_opp_add(cpu_dev, clk_get_rate(clk), 0); |
| if (ret) { |
| clk_put(clk); |
| return ret; |
| } |
| |
| ret = dev_pm_opp_add(cpu_dev, clk_get_rate(clk) / 2, 0); |
| if (ret) { |
| clk_put(clk); |
| return ret; |
| } |
| } |
| |
| platform_device_register_data(NULL, "cpufreq-dt", -1, |
| &cpufreq_dt_pd, sizeof(cpufreq_dt_pd)); |
| return 0; |
| } |
| |
| device_initcall(armada_xp_pmsu_cpufreq_init); |