s2io: Fixes in updating skb->truesize and code cleanup.
1. Fix for updating skb->truesize properly.
2. Disable NAPI only if more than one ring configured in case of MSI/MSI-X
interrupts. Previously we were disabling NAPI irrespective of number of
rings when MSI/MSI-X interrupts were used.
3. Code cleanup.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c
index 350723b..9b9b28e 100644
--- a/drivers/net/s2io.c
+++ b/drivers/net/s2io.c
@@ -459,7 +459,7 @@
void *tmp_v_addr, *tmp_v_addr_next;
dma_addr_t tmp_p_addr, tmp_p_addr_next;
RxD_block_t *pre_rxd_blk = NULL;
- int i, j, blk_cnt, rx_sz, tx_sz;
+ int i, j, blk_cnt;
int lst_size, lst_per_page;
struct net_device *dev = nic->dev;
unsigned long tmp;
@@ -484,7 +484,6 @@
}
lst_size = (sizeof(TxD_t) * config->max_txds);
- tx_sz = lst_size * size;
lst_per_page = PAGE_SIZE / lst_size;
for (i = 0; i < config->tx_fifo_num; i++) {
@@ -583,7 +582,6 @@
size = (size * (sizeof(RxD1_t)));
else
size = (size * (sizeof(RxD3_t)));
- rx_sz = size;
for (i = 0; i < config->rx_ring_num; i++) {
mac_control->rings[i].rx_curr_get_info.block_index = 0;
@@ -624,6 +622,8 @@
rx_blocks->rxds = kmalloc(sizeof(rxd_info_t)*
rxd_count[nic->rxd_mode],
GFP_KERNEL);
+ if (!rx_blocks->rxds)
+ return -ENOMEM;
for (l=0; l<rxd_count[nic->rxd_mode];l++) {
rx_blocks->rxds[l].virt_addr =
rx_blocks->block_virt_addr +
@@ -2259,6 +2259,7 @@
return -ENOMEM ;
}
frag_list = skb_shinfo(skb)->frag_list;
+ skb->truesize += frag_list->truesize;
frag_list->next = NULL;
tmp = (void *)ALIGN((long)frag_list->data, ALIGN_SIZE + 1);
frag_list->data = tmp;
@@ -3185,6 +3186,8 @@
register u64 val64 = 0, err_reg = 0;
u64 cnt;
int i;
+ if (atomic_read(&nic->card_state) == CARD_DOWN)
+ return;
nic->mac_control.stats_info->sw_stat.ring_full_cnt = 0;
/* Handling the XPAK counters update */
if(nic->mac_control.stats_info->xpak_stat.xpak_timer_count < 72000) {
@@ -6576,7 +6579,6 @@
skb_put(skb, buf1_len);
skb->len += buf2_len;
skb->data_len += buf2_len;
- skb->truesize += buf2_len;
skb_put(skb_shinfo(skb)->frag_list, buf2_len);
sp->stats.rx_bytes += buf1_len;
@@ -6797,6 +6799,8 @@
"Defaulting to INTA\n");
*dev_intr_type = INTA;
}
+ if ( (rx_ring_num > 1) && (*dev_intr_type != INTA) )
+ napi = 0;
if (rx_ring_mode > 3) {
DBG_PRINT(ERR_DBG, "s2io: Requested ring mode not supported\n");
DBG_PRINT(ERR_DBG, "s2io: Defaulting to 3-buffer mode\n");
@@ -7312,7 +7316,7 @@
* Description: This function is the cleanup routine for the driver. It unregist * ers the driver.
*/
-static void s2io_closer(void)
+static __exit void s2io_closer(void)
{
pci_unregister_driver(&s2io_driver);
DBG_PRINT(INIT_DBG, "cleanup done\n");
@@ -7633,6 +7637,7 @@
lro->last_frag->next = skb;
else
skb_shinfo(first)->frag_list = skb;
+ first->truesize += skb->truesize;
lro->last_frag = skb;
sp->mac_control.stats_info->sw_stat.clubbed_frms_cnt++;
return;
