// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
 * Copyright 2022 Toradex
 */

/ {
	sound_card: sound-card {
		compatible = "simple-audio-card";
		simple-audio-card,bitclock-master = <&dailink_master>;
		simple-audio-card,format = "i2s";
		simple-audio-card,frame-master = <&dailink_master>;
		simple-audio-card,mclk-fs = <256>;
		simple-audio-card,name = "verdin-nau8822";
		simple-audio-card,routing =
			"Headphones", "LHP",
			"Headphones", "RHP",
			"Speaker", "LSPK",
			"Speaker", "RSPK",
			"Line Out", "AUXOUT1",
			"Line Out", "AUXOUT2",
			"LAUX", "Line In",
			"RAUX", "Line In",
			"LMICP", "Mic In",
			"RMICP", "Mic In";
		simple-audio-card,widgets =
			"Headphones", "Headphones",
			"Line Out", "Line Out",
			"Speaker", "Speaker",
			"Microphone", "Mic In",
			"Line", "Line In";

		dailink_master: simple-audio-card,codec {
			clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
			sound-dai = <&nau8822_1a>;
		};

		simple-audio-card,cpu {
			sound-dai = <&sai2>;
		};
	};
};

/* Verdin SPI_1 */
&ecspi2 {
	status = "okay";
};

/* EEPROM on display adapter boards */
&eeprom_display_adapter {
	status = "okay";
};

/* EEPROM on Verdin Development board */
&eeprom_carrier_board {
	status = "okay";
};

&fec1 {
	status = "okay";
};

/* Verdin QSPI_1 */
&flexspi {
	status = "okay";
};

/* Current measurement into module VCC */
&hwmon {
	status = "okay";
};

&hwmon_temp {
	vs-supply = <&reg_1p8v>;
	status = "okay";
};

&i2c3 {
	status = "okay";
};

&gpio5 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
};

&gpio_expander_21 {
	status = "okay";
};

/* Verdin I2C_1 */
&i2c4 {
	status = "okay";

	/* Audio Codec */
	nau8822_1a: audio-codec@1a {
		compatible = "nuvoton,nau8822";
		reg = <0x1a>;
		#sound-dai-cells = <0>;
	};
};

/* Verdin PCIE_1 */
&pcie0 {
	status = "okay";
};

&pcie_phy {
	status = "okay";
};

/* Verdin PWM_3_DSI */
&pwm1 {
	status = "okay";
};

/* Verdin PWM_1 */
&pwm2 {
	status = "okay";
};

/* Verdin PWM_2 */
&pwm3 {
	status = "okay";
};

/* Verdin I2S_1 */
&sai2 {
	status = "okay";
};

/* Verdin UART_3 */
&uart1 {
	status = "okay";
};

/* Verdin UART_1, connector X50 through RS485 transceiver */
&uart2 {
	linux,rs485-enabled-at-boot-time;
	rs485-rts-active-low;
	rs485-rx-during-tx;
	status = "okay";
};

/* Verdin UART_2 */
&uart3 {
	status = "okay";
};

/* Verdin USB_1 */
&usbotg1 {
	disable-over-current;
	status = "okay";
};

/* Verdin USB_2 */
&usbotg2 {
	disable-over-current;
	status = "okay";
};

/* Limit frequency on dev board due to long traces and bad signal integrity */
&usdhc2 {
	max-frequency = <100000000>;
	status = "okay";
};