// SPDX-License-Identifier: GPL-2.0-only
/*
 * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
 */

#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8996.h>
#include <dt-bindings/clock/qcom,mmcc-msm8996.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/interconnect/qcom,msm8996.h>
#include <dt-bindings/interconnect/qcom,msm8996-cbf.h>
#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,apr.h>
#include <dt-bindings/thermal/thermal.h>

/ {
	interrupt-parent = <&intc>;

	#address-cells = <2>;
	#size-cells = <2>;

	chosen { };

	clocks {
		xo_board: xo-board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <19200000>;
			clock-output-names = "xo_board";
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <32764>;
			clock-output-names = "sleep_clk";
		};
	};

	cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x0>;
			enable-method = "psci";
			cpu-idle-states = <&CPU_SLEEP_0>;
			capacity-dmips-mhz = <1024>;
			clocks = <&kryocc 0>;
			interconnects = <&cbf MASTER_CBF_M4M &cbf SLAVE_CBF_M4M>;
			operating-points-v2 = <&cluster0_opp>;
			#cooling-cells = <2>;
			next-level-cache = <&L2_0>;
			L2_0: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
			};
		};

		CPU1: cpu@1 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x1>;
			enable-method = "psci";
			cpu-idle-states = <&CPU_SLEEP_0>;
			capacity-dmips-mhz = <1024>;
			clocks = <&kryocc 0>;
			interconnects = <&cbf MASTER_CBF_M4M &cbf SLAVE_CBF_M4M>;
			operating-points-v2 = <&cluster0_opp>;
			#cooling-cells = <2>;
			next-level-cache = <&L2_0>;
		};

		CPU2: cpu@100 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x100>;
			enable-method = "psci";
			cpu-idle-states = <&CPU_SLEEP_0>;
			capacity-dmips-mhz = <1024>;
			clocks = <&kryocc 1>;
			interconnects = <&cbf MASTER_CBF_M4M &cbf SLAVE_CBF_M4M>;
			operating-points-v2 = <&cluster1_opp>;
			#cooling-cells = <2>;
			next-level-cache = <&L2_1>;
			L2_1: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
			};
		};

		CPU3: cpu@101 {
			device_type = "cpu";
			compatible = "qcom,kryo";
			reg = <0x0 0x101>;
			enable-method = "psci";
			cpu-idle-states = <&CPU_SLEEP_0>;
			capacity-dmips-mhz = <1024>;
			clocks = <&kryocc 1>;
			interconnects = <&cbf MASTER_CBF_M4M &cbf SLAVE_CBF_M4M>;
			operating-points-v2 = <&cluster1_opp>;
			#cooling-cells = <2>;
			next-level-cache = <&L2_1>;
		};

		cpu-map {
			cluster0 {
				core0 {
					cpu = <&CPU0>;
				};

				core1 {
					cpu = <&CPU1>;
				};
			};

			cluster1 {
				core0 {
					cpu = <&CPU2>;
				};

				core1 {
					cpu = <&CPU3>;
				};
			};
		};

		idle-states {
			entry-method = "psci";

			CPU_SLEEP_0: cpu-sleep-0 {
				compatible = "arm,idle-state";
				idle-state-name = "standalone-power-collapse";
				arm,psci-suspend-param = <0x00000004>;
				entry-latency-us = <130>;
				exit-latency-us = <80>;
				min-residency-us = <300>;
			};
		};
	};

	cluster0_opp: opp-table-cluster0 {
		compatible = "operating-points-v2-kryo-cpu";
		nvmem-cells = <&speedbin_efuse>;
		opp-shared;

		/* Nominal fmax for now */
		opp-307200000 {
			opp-hz = /bits/ 64 <307200000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-422400000 {
			opp-hz = /bits/ 64 <422400000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-480000000 {
			opp-hz = /bits/ 64 <480000000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-556800000 {
			opp-hz = /bits/ 64 <556800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-652800000 {
			opp-hz = /bits/ 64 <652800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <384000>;
		};
		opp-729600000 {
			opp-hz = /bits/ 64 <729600000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <460800>;
		};
		opp-844800000 {
			opp-hz = /bits/ 64 <844800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <537600>;
		};
		opp-960000000 {
			opp-hz = /bits/ 64 <960000000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <672000>;
		};
		opp-1036800000 {
			opp-hz = /bits/ 64 <1036800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <672000>;
		};
		opp-1113600000 {
			opp-hz = /bits/ 64 <1113600000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <825600>;
		};
		opp-1190400000 {
			opp-hz = /bits/ 64 <1190400000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <825600>;
		};
		opp-1228800000 {
			opp-hz = /bits/ 64 <1228800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <902400>;
		};
		opp-1324800000 {
			opp-hz = /bits/ 64 <1324800000>;
			opp-supported-hw = <0xd>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1056000>;
		};
		opp-1363200000 {
			opp-hz = /bits/ 64 <1363200000>;
			opp-supported-hw = <0x2>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1132800>;
		};
		opp-1401600000 {
			opp-hz = /bits/ 64 <1401600000>;
			opp-supported-hw = <0xd>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1132800>;
		};
		opp-1478400000 {
			opp-hz = /bits/ 64 <1478400000>;
			opp-supported-hw = <0x9>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1190400>;
		};
		opp-1497600000 {
			opp-hz = /bits/ 64 <1497600000>;
			opp-supported-hw = <0x04>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1305600>;
		};
		opp-1593600000 {
			opp-hz = /bits/ 64 <1593600000>;
			opp-supported-hw = <0x9>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1382400>;
		};
	};

	cluster1_opp: opp-table-cluster1 {
		compatible = "operating-points-v2-kryo-cpu";
		nvmem-cells = <&speedbin_efuse>;
		opp-shared;

		/* Nominal fmax for now */
		opp-307200000 {
			opp-hz = /bits/ 64 <307200000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-403200000 {
			opp-hz = /bits/ 64 <403200000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-480000000 {
			opp-hz = /bits/ 64 <480000000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-556800000 {
			opp-hz = /bits/ 64 <556800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-652800000 {
			opp-hz = /bits/ 64 <652800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-729600000 {
			opp-hz = /bits/ 64 <729600000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <307200>;
		};
		opp-806400000 {
			opp-hz = /bits/ 64 <806400000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <384000>;
		};
		opp-883200000 {
			opp-hz = /bits/ 64 <883200000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <460800>;
		};
		opp-940800000 {
			opp-hz = /bits/ 64 <940800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <537600>;
		};
		opp-1036800000 {
			opp-hz = /bits/ 64 <1036800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <595200>;
		};
		opp-1113600000 {
			opp-hz = /bits/ 64 <1113600000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <672000>;
		};
		opp-1190400000 {
			opp-hz = /bits/ 64 <1190400000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <672000>;
		};
		opp-1248000000 {
			opp-hz = /bits/ 64 <1248000000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <748800>;
		};
		opp-1324800000 {
			opp-hz = /bits/ 64 <1324800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <825600>;
		};
		opp-1401600000 {
			opp-hz = /bits/ 64 <1401600000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <902400>;
		};
		opp-1478400000 {
			opp-hz = /bits/ 64 <1478400000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <979200>;
		};
		opp-1555200000 {
			opp-hz = /bits/ 64 <1555200000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1056000>;
		};
		opp-1632000000 {
			opp-hz = /bits/ 64 <1632000000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1190400>;
		};
		opp-1708800000 {
			opp-hz = /bits/ 64 <1708800000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1228800>;
		};
		opp-1785600000 {
			opp-hz = /bits/ 64 <1785600000>;
			opp-supported-hw = <0xf>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1305600>;
		};
		opp-1804800000 {
			opp-hz = /bits/ 64 <1804800000>;
			opp-supported-hw = <0xe>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1305600>;
		};
		opp-1824000000 {
			opp-hz = /bits/ 64 <1824000000>;
			opp-supported-hw = <0x1>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1382400>;
		};
		opp-1900800000 {
			opp-hz = /bits/ 64 <1900800000>;
			opp-supported-hw = <0x4>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1305600>;
		};
		opp-1920000000 {
			opp-hz = /bits/ 64 <1920000000>;
			opp-supported-hw = <0x1>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1459200>;
		};
		opp-1996800000 {
			opp-hz = /bits/ 64 <1996800000>;
			opp-supported-hw = <0x1>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1593600>;
		};
		opp-2073600000 {
			opp-hz = /bits/ 64 <2073600000>;
			opp-supported-hw = <0x1>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1593600>;
		};
		opp-2150400000 {
			opp-hz = /bits/ 64 <2150400000>;
			opp-supported-hw = <0x1>;
			clock-latency-ns = <200000>;
			opp-peak-kBps = <1593600>;
		};
	};

	firmware {
		scm {
			compatible = "qcom,scm-msm8996", "qcom,scm";
			qcom,dload-mode = <&tcsr_2 0x13000>;
		};
	};

	memory@80000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the reg */
		reg = <0x0 0x80000000 0x0 0x0>;
	};

	etm {
		compatible = "qcom,coresight-remote-etm";

		out-ports {
			port {
				modem_etm_out_funnel_in2: endpoint {
					remote-endpoint =
					  <&funnel_in2_in_modem_etm>;
				};
			};
		};
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";
	};

	rpm: remoteproc {
		compatible = "qcom,msm8996-rpm-proc", "qcom,rpm-proc";

		glink-edge {
			compatible = "qcom,glink-rpm";
			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
			qcom,rpm-msg-ram = <&rpm_msg_ram>;
			mboxes = <&apcs_glb 0>;

			rpm_requests: rpm-requests {
				compatible = "qcom,rpm-msm8996", "qcom,glink-smd-rpm";
				qcom,glink-channels = "rpm_requests";

				rpmcc: clock-controller {
					compatible = "qcom,rpmcc-msm8996", "qcom,rpmcc";
					#clock-cells = <1>;
					clocks = <&xo_board>;
					clock-names = "xo";
				};

				rpmpd: power-controller {
					compatible = "qcom,msm8996-rpmpd";
					#power-domain-cells = <1>;
					operating-points-v2 = <&rpmpd_opp_table>;

					rpmpd_opp_table: opp-table {
						compatible = "operating-points-v2";

						rpmpd_opp1: opp1 {
							opp-level = <1>;
						};

						rpmpd_opp2: opp2 {
							opp-level = <2>;
						};

						rpmpd_opp3: opp3 {
							opp-level = <3>;
						};

						rpmpd_opp4: opp4 {
							opp-level = <4>;
						};

						rpmpd_opp5: opp5 {
							opp-level = <5>;
						};

						rpmpd_opp6: opp6 {
							opp-level = <6>;
						};
					};
				};
			};
		};
	};

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		hyp_mem: memory@85800000 {
			reg = <0x0 0x85800000 0x0 0x600000>;
			no-map;
		};

		xbl_mem: memory@85e00000 {
			reg = <0x0 0x85e00000 0x0 0x200000>;
			no-map;
		};

		smem_mem: smem-mem@86000000 {
			reg = <0x0 0x86000000 0x0 0x200000>;
			no-map;
		};

		tz_mem: memory@86200000 {
			reg = <0x0 0x86200000 0x0 0x2600000>;
			no-map;
		};

		rmtfs_mem: rmtfs {
			compatible = "qcom,rmtfs-mem";

			size = <0x0 0x200000>;
			alloc-ranges = <0x0 0xa0000000 0x0 0x2000000>;
			no-map;

			qcom,client-id = <1>;
			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
		};

		mpss_mem: mpss@88800000 {
			reg = <0x0 0x88800000 0x0 0x6200000>;
			no-map;
		};

		adsp_mem: adsp@8ea00000 {
			reg = <0x0 0x8ea00000 0x0 0x1b00000>;
			no-map;
		};

		slpi_mem: slpi@90500000 {
			reg = <0x0 0x90500000 0x0 0xa00000>;
			no-map;
		};

		gpu_mem: gpu@90f00000 {
			compatible = "shared-dma-pool";
			reg = <0x0 0x90f00000 0x0 0x100000>;
			no-map;
		};

		venus_mem: venus@91000000 {
			reg = <0x0 0x91000000 0x0 0x500000>;
			no-map;
		};

		mba_mem: mba@91500000 {
			reg = <0x0 0x91500000 0x0 0x200000>;
			no-map;
		};

		mdata_mem: mpss-metadata {
			alloc-ranges = <0x0 0xa0000000 0x0 0x20000000>;
			size = <0x0 0x4000>;
			no-map;
		};
	};

	smem {
		compatible = "qcom,smem";
		memory-region = <&smem_mem>;
		hwlocks = <&tcsr_mutex 3>;
	};

	smp2p-adsp {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;

		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apcs_glb 10>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		adsp_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		adsp_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-mpss {
		compatible = "qcom,smp2p";
		qcom,smem = <435>, <428>;

		interrupts = <GIC_SPI 451 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apcs_glb 14>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <1>;

		mpss_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		mpss_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-slpi {
		compatible = "qcom,smp2p";
		qcom,smem = <481>, <430>;

		interrupts = <GIC_SPI 178 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apcs_glb 26>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <3>;

		slpi_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		slpi_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges = <0 0 0 0xffffffff>;
		compatible = "simple-bus";

		pcie_phy: phy-wrapper@34000 {
			compatible = "qcom,msm8996-qmp-pcie-phy";
			reg = <0x00034000 0x488>;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x00034000 0x4000>;

			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				<&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
				<&gcc GCC_PCIE_CLKREF_CLK>;
			clock-names = "aux", "cfg_ahb", "ref";

			resets = <&gcc GCC_PCIE_PHY_BCR>,
				<&gcc GCC_PCIE_PHY_COM_BCR>,
				<&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
			reset-names = "phy", "common", "cfg";

			status = "disabled";

			pciephy_0: phy@1000 {
				reg = <0x1000 0x130>,
				      <0x1200 0x200>,
				      <0x1400 0x1dc>;

				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
				clock-names = "pipe0";
				resets = <&gcc GCC_PCIE_0_PHY_BCR>;
				reset-names = "lane0";

				#clock-cells = <0>;
				clock-output-names = "pcie_0_pipe_clk_src";

				#phy-cells = <0>;
			};

			pciephy_1: phy@2000 {
				reg = <0x2000 0x130>,
				      <0x2200 0x200>,
				      <0x2400 0x1dc>;

				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
				clock-names = "pipe1";
				resets = <&gcc GCC_PCIE_1_PHY_BCR>;
				reset-names = "lane1";

				#clock-cells = <0>;
				clock-output-names = "pcie_1_pipe_clk_src";

				#phy-cells = <0>;
			};

			pciephy_2: phy@3000 {
				reg = <0x3000 0x130>,
				      <0x3200 0x200>,
				      <0x3400 0x1dc>;

				clocks = <&gcc GCC_PCIE_2_PIPE_CLK>;
				clock-names = "pipe2";
				resets = <&gcc GCC_PCIE_2_PHY_BCR>;
				reset-names = "lane2";

				#clock-cells = <0>;
				clock-output-names = "pcie_2_pipe_clk_src";

				#phy-cells = <0>;
			};
		};

		rpm_msg_ram: sram@68000 {
			compatible = "qcom,rpm-msg-ram";
			reg = <0x00068000 0x6000>;
		};

		qfprom@74000 {
			compatible = "qcom,msm8996-qfprom", "qcom,qfprom";
			reg = <0x00074000 0x8ff>;
			#address-cells = <1>;
			#size-cells = <1>;

			qusb2p_hstx_trim: hstx-trim@24e {
				reg = <0x24e 0x2>;
				bits = <5 4>;
			};

			qusb2s_hstx_trim: hstx-trim@24f {
				reg = <0x24f 0x1>;
				bits = <1 4>;
			};

			speedbin_efuse: speedbin@133 {
				reg = <0x133 0x1>;
				bits = <5 3>;
			};
		};

		rng: rng@83000 {
			compatible = "qcom,prng-ee";
			reg = <0x00083000 0x1000>;
			clocks = <&gcc GCC_PRNG_AHB_CLK>;
			clock-names = "core";
		};

		gcc: clock-controller@300000 {
			compatible = "qcom,gcc-msm8996";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			reg = <0x00300000 0x90000>;

			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
				 <&rpmcc RPM_SMD_LN_BB_CLK>,
				 <&sleep_clk>,
				 <&pciephy_0>,
				 <&pciephy_1>,
				 <&pciephy_2>,
				 <&usb3phy>,
				 <&ufsphy 0>,
				 <&ufsphy 1>,
				 <&ufsphy 2>;
			clock-names = "cxo",
				      "cxo2",
				      "sleep_clk",
				      "pcie_0_pipe_clk_src",
				      "pcie_1_pipe_clk_src",
				      "pcie_2_pipe_clk_src",
				      "usb3_phy_pipe_clk_src",
				      "ufs_rx_symbol_0_clk_src",
				      "ufs_rx_symbol_1_clk_src",
				      "ufs_tx_symbol_0_clk_src";
		};

		bimc: interconnect@408000 {
			compatible = "qcom,msm8996-bimc";
			reg = <0x00408000 0x5a000>;
			#interconnect-cells = <1>;
		};

		tsens0: thermal-sensor@4a9000 {
			compatible = "qcom,msm8996-tsens", "qcom,tsens-v2";
			reg = <0x004a9000 0x1000>, /* TM */
			      <0x004a8000 0x1000>; /* SROT */
			#qcom,sensors = <13>;
			interrupts = <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens1: thermal-sensor@4ad000 {
			compatible = "qcom,msm8996-tsens", "qcom,tsens-v2";
			reg = <0x004ad000 0x1000>, /* TM */
			      <0x004ac000 0x1000>; /* SROT */
			#qcom,sensors = <8>;
			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		cryptobam: dma-controller@644000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x00644000 0x24000>;
			interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_CE1_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
			qcom,controlled-remotely;
		};

		crypto: crypto@67a000 {
			compatible = "qcom,crypto-v5.4";
			reg = <0x0067a000 0x6000>;
			clocks = <&gcc GCC_CE1_AHB_CLK>,
				 <&gcc GCC_CE1_AXI_CLK>,
				 <&gcc GCC_CE1_CLK>;
			clock-names = "iface", "bus", "core";
			dmas = <&cryptobam 6>, <&cryptobam 7>;
			dma-names = "rx", "tx";
		};

		cnoc: interconnect@500000 {
			compatible = "qcom,msm8996-cnoc";
			reg = <0x00500000 0x1000>;
			#interconnect-cells = <1>;
		};

		snoc: interconnect@524000 {
			compatible = "qcom,msm8996-snoc";
			reg = <0x00524000 0x1c000>;
			#interconnect-cells = <1>;
		};

		a0noc: interconnect@543000 {
			compatible = "qcom,msm8996-a0noc";
			reg = <0x00543000 0x6000>;
			#interconnect-cells = <1>;
			clock-names = "aggre0_snoc_axi",
				      "aggre0_cnoc_ahb",
				      "aggre0_noc_mpu_cfg";
			clocks = <&gcc GCC_AGGRE0_SNOC_AXI_CLK>,
				 <&gcc GCC_AGGRE0_CNOC_AHB_CLK>,
				 <&gcc GCC_AGGRE0_NOC_MPU_CFG_AHB_CLK>;
			power-domains = <&gcc AGGRE0_NOC_GDSC>;
		};

		a1noc: interconnect@562000 {
			compatible = "qcom,msm8996-a1noc";
			reg = <0x00562000 0x5000>;
			#interconnect-cells = <1>;
		};

		a2noc: interconnect@583000 {
			compatible = "qcom,msm8996-a2noc";
			reg = <0x00583000 0x7000>;
			#interconnect-cells = <1>;
			clock-names = "aggre2_ufs_axi", "ufs_axi";
			clocks = <&gcc GCC_AGGRE2_UFS_AXI_CLK>,
				 <&gcc GCC_UFS_AXI_CLK>;
		};

		mnoc: interconnect@5a4000 {
			compatible = "qcom,msm8996-mnoc";
			reg = <0x005a4000 0x1c000>;
			#interconnect-cells = <1>;
			clock-names = "iface";
			clocks = <&mmcc AHB_CLK_SRC>;
		};

		pnoc: interconnect@5c0000 {
			compatible = "qcom,msm8996-pnoc";
			reg = <0x005c0000 0x3000>;
			#interconnect-cells = <1>;
		};

		tcsr_mutex: hwlock@740000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0x00740000 0x20000>;
			#hwlock-cells = <1>;
		};

		tcsr_1: syscon@760000 {
			compatible = "qcom,tcsr-msm8996", "syscon";
			reg = <0x00760000 0x20000>;
		};

		tcsr_2: syscon@7a0000 {
			compatible = "qcom,tcsr-msm8996", "syscon";
			reg = <0x007a0000 0x18000>;
		};

		mmcc: clock-controller@8c0000 {
			compatible = "qcom,mmcc-msm8996";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			reg = <0x008c0000 0x40000>;
			clocks = <&xo_board>,
				 <&gcc GPLL0>,
				 <&gcc GCC_MMSS_NOC_CFG_AHB_CLK>,
				 <&mdss_dsi0_phy 1>,
				 <&mdss_dsi0_phy 0>,
				 <&mdss_dsi1_phy 1>,
				 <&mdss_dsi1_phy 0>,
				 <&mdss_hdmi_phy>;
			clock-names = "xo",
				      "gpll0",
				      "gcc_mmss_noc_cfg_ahb_clk",
				      "dsi0pll",
				      "dsi0pllbyte",
				      "dsi1pll",
				      "dsi1pllbyte",
				      "hdmipll";
			assigned-clocks = <&mmcc MMPLL9_PLL>,
					  <&mmcc MMPLL1_PLL>,
					  <&mmcc MMPLL3_PLL>,
					  <&mmcc MMPLL4_PLL>,
					  <&mmcc MMPLL5_PLL>;
			assigned-clock-rates = <624000000>,
					       <810000000>,
					       <980000000>,
					       <960000000>,
					       <825000000>;
		};

		mdss: display-subsystem@900000 {
			compatible = "qcom,mdss";

			reg = <0x00900000 0x1000>,
			      <0x009b0000 0x1040>,
			      <0x009b8000 0x1040>;
			reg-names = "mdss_phys",
				    "vbif_phys",
				    "vbif_nrt_phys";

			power-domains = <&mmcc MDSS_GDSC>;
			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;

			interrupt-controller;
			#interrupt-cells = <1>;

			clocks = <&mmcc MDSS_AHB_CLK>,
				 <&mmcc MDSS_MDP_CLK>;
			clock-names = "iface", "core";

			resets = <&mmcc MDSS_BCR>;

			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			status = "disabled";

			mdp: display-controller@901000 {
				compatible = "qcom,msm8996-mdp5", "qcom,mdp5";
				reg = <0x00901000 0x90000>;
				reg-names = "mdp_phys";

				interrupt-parent = <&mdss>;
				interrupts = <0>;

				clocks = <&mmcc MDSS_AHB_CLK>,
					 <&mmcc MDSS_AXI_CLK>,
					 <&mmcc MDSS_MDP_CLK>,
					 <&mmcc SMMU_MDP_AXI_CLK>,
					 <&mmcc MDSS_VSYNC_CLK>;
				clock-names = "iface",
					      "bus",
					      "core",
					      "iommu",
					      "vsync";

				iommus = <&mdp_smmu 0>;

				assigned-clocks = <&mmcc MDSS_MDP_CLK>,
					 <&mmcc MDSS_VSYNC_CLK>;
				assigned-clock-rates = <300000000>,
					 <19200000>;

				interconnects = <&mnoc MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
						<&mnoc MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
						<&mnoc MASTER_ROTATOR &bimc SLAVE_EBI_CH0>;
				interconnect-names = "mdp0-mem", "mdp1-mem", "rotator-mem";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdp5_intf3_out: endpoint {
							remote-endpoint = <&mdss_hdmi_in>;
						};
					};

					port@1 {
						reg = <1>;
						mdp5_intf1_out: endpoint {
							remote-endpoint = <&mdss_dsi0_in>;
						};
					};

					port@2 {
						reg = <2>;
						mdp5_intf2_out: endpoint {
							remote-endpoint = <&mdss_dsi1_in>;
						};
					};
				};
			};

			mdss_dsi0: dsi@994000 {
				compatible = "qcom,msm8996-dsi-ctrl",
					     "qcom,mdss-dsi-ctrl";
				reg = <0x00994000 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <4>;

				clocks = <&mmcc MDSS_MDP_CLK>,
					 <&mmcc MDSS_BYTE0_CLK>,
					 <&mmcc MDSS_AHB_CLK>,
					 <&mmcc MDSS_AXI_CLK>,
					 <&mmcc MMSS_MISC_AHB_CLK>,
					 <&mmcc MDSS_PCLK0_CLK>,
					 <&mmcc MDSS_ESC0_CLK>;
				clock-names = "mdp_core",
					      "byte",
					      "iface",
					      "bus",
					      "core_mmss",
					      "pixel",
					      "core";
				assigned-clocks = <&mmcc BYTE0_CLK_SRC>, <&mmcc PCLK0_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;

				phys = <&mdss_dsi0_phy>;
				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi0_in: endpoint {
							remote-endpoint = <&mdp5_intf1_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi0_out: endpoint {
						};
					};
				};
			};

			mdss_dsi0_phy: phy@994400 {
				compatible = "qcom,dsi-phy-14nm";
				reg = <0x00994400 0x100>,
				      <0x00994500 0x300>,
				      <0x00994800 0x188>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
				clock-names = "iface", "ref";
				status = "disabled";
			};

			mdss_dsi1: dsi@996000 {
				compatible = "qcom,msm8996-dsi-ctrl",
					     "qcom,mdss-dsi-ctrl";
				reg = <0x00996000 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <5>;

				clocks = <&mmcc MDSS_MDP_CLK>,
					 <&mmcc MDSS_BYTE1_CLK>,
					 <&mmcc MDSS_AHB_CLK>,
					 <&mmcc MDSS_AXI_CLK>,
					 <&mmcc MMSS_MISC_AHB_CLK>,
					 <&mmcc MDSS_PCLK1_CLK>,
					 <&mmcc MDSS_ESC1_CLK>;
				clock-names = "mdp_core",
					      "byte",
					      "iface",
					      "bus",
					      "core_mmss",
					      "pixel",
					      "core";
				assigned-clocks = <&mmcc BYTE1_CLK_SRC>, <&mmcc PCLK1_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;

				phys = <&mdss_dsi1_phy>;
				status = "disabled";

				#address-cells = <1>;
				#size-cells = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi1_in: endpoint {
							remote-endpoint = <&mdp5_intf2_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi1_out: endpoint {
						};
					};
				};
			};

			mdss_dsi1_phy: phy@996400 {
				compatible = "qcom,dsi-phy-14nm";
				reg = <0x00996400 0x100>,
				      <0x00996500 0x300>,
				      <0x00996800 0x188>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
				clock-names = "iface", "ref";
				status = "disabled";
			};

			mdss_hdmi: hdmi-tx@9a0000 {
				compatible = "qcom,hdmi-tx-8996";
				reg = <0x009a0000 0x50c>,
				      <0x00070000 0x6158>,
				      <0x009e0000 0xfff>;
				reg-names = "core_physical",
					    "qfprom_physical",
					    "hdcp_physical";

				interrupt-parent = <&mdss>;
				interrupts = <8>;

				clocks = <&mmcc MDSS_MDP_CLK>,
					 <&mmcc MDSS_AHB_CLK>,
					 <&mmcc MDSS_HDMI_CLK>,
					 <&mmcc MDSS_HDMI_AHB_CLK>,
					 <&mmcc MDSS_EXTPCLK_CLK>;
				clock-names =
					"mdp_core",
					"iface",
					"core",
					"alt_iface",
					"extp";

				phys = <&mdss_hdmi_phy>;
				#sound-dai-cells = <1>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_hdmi_in: endpoint {
							remote-endpoint = <&mdp5_intf3_out>;
						};
					};
				};
			};

			mdss_hdmi_phy: phy@9a0600 {
				#phy-cells = <0>;
				compatible = "qcom,hdmi-phy-8996";
				reg = <0x009a0600 0x1c4>,
				      <0x009a0a00 0x124>,
				      <0x009a0c00 0x124>,
				      <0x009a0e00 0x124>,
				      <0x009a1000 0x124>,
				      <0x009a1200 0x0c8>;
				reg-names = "hdmi_pll",
					    "hdmi_tx_l0",
					    "hdmi_tx_l1",
					    "hdmi_tx_l2",
					    "hdmi_tx_l3",
					    "hdmi_phy";

				clocks = <&mmcc MDSS_AHB_CLK>,
					 <&gcc GCC_HDMI_CLKREF_CLK>,
					 <&xo_board>;
				clock-names = "iface",
					      "ref",
					      "xo";

				#clock-cells = <0>;

				status = "disabled";
			};
		};

		gpu: gpu@b00000 {
			compatible = "qcom,adreno-530.2", "qcom,adreno";

			reg = <0x00b00000 0x3f000>;
			reg-names = "kgsl_3d0_reg_memory";

			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&mmcc GPU_GX_GFX3D_CLK>,
				<&mmcc GPU_AHB_CLK>,
				<&mmcc GPU_GX_RBBMTIMER_CLK>,
				<&gcc GCC_BIMC_GFX_CLK>,
				<&gcc GCC_MMSS_BIMC_GFX_CLK>;

			clock-names = "core",
				"iface",
				"rbbmtimer",
				"mem",
				"mem_iface";

			interconnects = <&bimc MASTER_GRAPHICS_3D &bimc SLAVE_EBI_CH0>;
			interconnect-names = "gfx-mem";

			power-domains = <&mmcc GPU_GX_GDSC>;
			iommus = <&adreno_smmu 0>;

			nvmem-cells = <&speedbin_efuse>;
			nvmem-cell-names = "speed_bin";

			operating-points-v2 = <&gpu_opp_table>;

			status = "disabled";

			#cooling-cells = <2>;

			gpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				/*
				 * 624Mhz is only available on speed bins 0 and 3.
				 * 560Mhz is only available on speed bins 0, 2 and 3.
				 * All the rest are available on all bins of the hardware.
				 */
				opp-624000000 {
					opp-hz = /bits/ 64 <624000000>;
					opp-supported-hw = <0x09>;
				};
				opp-560000000 {
					opp-hz = /bits/ 64 <560000000>;
					opp-supported-hw = <0x0d>;
				};
				opp-510000000 {
					opp-hz = /bits/ 64 <510000000>;
					opp-supported-hw = <0xff>;
				};
				opp-401800000 {
					opp-hz = /bits/ 64 <401800000>;
					opp-supported-hw = <0xff>;
				};
				opp-315000000 {
					opp-hz = /bits/ 64 <315000000>;
					opp-supported-hw = <0xff>;
				};
				opp-214000000 {
					opp-hz = /bits/ 64 <214000000>;
					opp-supported-hw = <0xff>;
				};
				opp-133000000 {
					opp-hz = /bits/ 64 <133000000>;
					opp-supported-hw = <0xff>;
				};
			};

			zap-shader {
				memory-region = <&gpu_mem>;
			};
		};

		tlmm: pinctrl@1010000 {
			compatible = "qcom,msm8996-pinctrl";
			reg = <0x01010000 0x300000>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			gpio-ranges = <&tlmm 0 0 150>;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;

			blsp1_spi1_default: blsp1-spi1-default-state {
				spi-pins {
					pins = "gpio0", "gpio1", "gpio3";
					function = "blsp_spi1";
					drive-strength = <12>;
					bias-disable;
				};

				cs-pins {
					pins = "gpio2";
					function = "gpio";
					drive-strength = <16>;
					bias-disable;
					output-high;
				};
			};

			blsp1_spi1_sleep: blsp1-spi1-sleep-state {
				pins = "gpio0", "gpio1", "gpio2", "gpio3";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			blsp2_uart2_2pins_default: blsp2-uart2-2pins-state {
				pins = "gpio4", "gpio5";
				function = "blsp_uart8";
				drive-strength = <16>;
				bias-disable;
			};

			blsp2_uart2_2pins_sleep: blsp2-uart2-2pins-sleep-state {
				pins = "gpio4", "gpio5";
				function = "gpio";
				drive-strength = <2>;
				bias-disable;
			};

			blsp2_i2c2_default: blsp2-i2c2-state {
				pins = "gpio6", "gpio7";
				function = "blsp_i2c8";
				drive-strength = <16>;
				bias-disable;
			};

			blsp2_i2c2_sleep: blsp2-i2c2-sleep-state {
				pins = "gpio6", "gpio7";
				function = "gpio";
				drive-strength = <2>;
				bias-disable;
			};

			blsp1_i2c6_default: blsp1-i2c6-state {
				pins = "gpio27", "gpio28";
				function = "blsp_i2c6";
				drive-strength = <16>;
				bias-disable;
			};

			blsp1_i2c6_sleep: blsp1-i2c6-sleep-state {
				pins = "gpio27", "gpio28";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-up;
			};

			cci0_default: cci0-default-state {
				pins = "gpio17", "gpio18";
				function = "cci_i2c";
				drive-strength = <16>;
				bias-disable;
			};

			camera0_state_on:
			camera_rear_default: camera-rear-default-state {
				camera0_mclk: mclk0-pins {
					pins = "gpio13";
					function = "cam_mclk";
					drive-strength = <16>;
					bias-disable;
				};

				camera0_rst: rst-pins {
					pins = "gpio25";
					function = "gpio";
					drive-strength = <16>;
					bias-disable;
				};

				camera0_pwdn: pwdn-pins {
					pins = "gpio26";
					function = "gpio";
					drive-strength = <16>;
					bias-disable;
				};
			};

			cci1_default: cci1-default-state {
				pins = "gpio19", "gpio20";
				function = "cci_i2c";
				drive-strength = <16>;
				bias-disable;
			};

			camera1_state_on:
			camera_board_default: camera-board-default-state {
				mclk1-pins {
					pins = "gpio14";
					function = "cam_mclk";
					drive-strength = <16>;
					bias-disable;
				};

				pwdn-pins {
					pins = "gpio98";
					function = "gpio";
					drive-strength = <16>;
					bias-disable;
				};

				rst-pins {
					pins = "gpio104";
					function = "gpio";
					drive-strength = <16>;
					bias-disable;
				};
			};

			camera2_state_on:
			camera_front_default: camera-front-default-state {
				camera2_mclk: mclk2-pins {
					pins = "gpio15";
					function = "cam_mclk";
					drive-strength = <16>;
					bias-disable;
				};

				camera2_rst: rst-pins {
					pins = "gpio23";
					function = "gpio";
					drive-strength = <16>;
					bias-disable;
				};

				pwdn-pins {
					pins = "gpio133";
					function = "gpio";
					drive-strength = <16>;
					bias-disable;
				};
			};

			pcie0_state_on: pcie0-state-on-state {
				perst-pins {
					pins = "gpio35";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio36";
					function = "pci_e0";
					drive-strength = <2>;
					bias-pull-up;
				};

				wake-pins {
					pins = "gpio37";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			pcie0_state_off: pcie0-state-off-state {
				perst-pins {
					pins = "gpio35";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio36";
					function = "gpio";
					drive-strength = <2>;
					bias-disable;
				};

				wake-pins {
					pins = "gpio37";
					function = "gpio";
					drive-strength = <2>;
					bias-disable;
				};
			};

			blsp1_uart2_default: blsp1-uart2-default-state {
				pins = "gpio41", "gpio42", "gpio43", "gpio44";
				function = "blsp_uart2";
				drive-strength = <16>;
				bias-disable;
			};

			blsp1_uart2_sleep: blsp1-uart2-sleep-state {
				pins = "gpio41", "gpio42", "gpio43", "gpio44";
				function = "gpio";
				drive-strength = <2>;
				bias-disable;
			};

			blsp1_i2c3_default: blsp1-i2c3-default-state {
				pins = "gpio47", "gpio48";
				function = "blsp_i2c3";
				drive-strength = <16>;
				bias-disable;
			};

			blsp1_i2c3_sleep: blsp1-i2c3-sleep-state {
				pins = "gpio47", "gpio48";
				function = "gpio";
				drive-strength = <2>;
				bias-disable;
			};

			blsp2_uart3_4pins_default: blsp2-uart3-4pins-state {
				pins = "gpio49", "gpio50", "gpio51", "gpio52";
				function = "blsp_uart9";
				drive-strength = <16>;
				bias-disable;
			};

			blsp2_uart3_4pins_sleep: blsp2-uart3-4pins-sleep-state {
				pins = "gpio49", "gpio50", "gpio51", "gpio52";
				function = "blsp_uart9";
				drive-strength = <2>;
				bias-disable;
			};

			blsp2_i2c3_default: blsp2-i2c3-state-state {
				pins = "gpio51", "gpio52";
				function = "blsp_i2c9";
				drive-strength = <16>;
				bias-disable;
			};

			blsp2_i2c3_sleep: blsp2-i2c3-sleep-state {
				pins = "gpio51", "gpio52";
				function = "gpio";
				drive-strength = <2>;
				bias-disable;
			};

			wcd_intr_default: wcd-intr-default-state {
				pins = "gpio54";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			blsp2_i2c1_default: blsp2-i2c1-state {
				pins = "gpio55", "gpio56";
				function = "blsp_i2c7";
				drive-strength = <16>;
				bias-disable;
			};

			blsp2_i2c1_sleep: blsp2-i2c1-sleep-state {
				pins = "gpio55", "gpio56";
				function = "gpio";
				drive-strength = <2>;
				bias-disable;
			};

			blsp2_i2c5_default: blsp2-i2c5-state {
				pins = "gpio60", "gpio61";
				function = "blsp_i2c11";
				drive-strength = <2>;
				bias-disable;
			};

			/* Sleep state for BLSP2_I2C5 is missing.. */

			cdc_reset_active: cdc-reset-active-state {
				pins = "gpio64";
				function = "gpio";
				drive-strength = <16>;
				bias-pull-down;
				output-high;
			};

			cdc_reset_sleep: cdc-reset-sleep-state {
				pins = "gpio64";
				function = "gpio";
				drive-strength = <16>;
				bias-disable;
				output-low;
			};

			blsp2_spi6_default: blsp2-spi6-default-state {
				spi-pins {
					pins = "gpio85", "gpio86", "gpio88";
					function = "blsp_spi12";
					drive-strength = <12>;
					bias-disable;
				};

				cs-pins {
					pins = "gpio87";
					function = "gpio";
					drive-strength = <16>;
					bias-disable;
					output-high;
				};
			};

			blsp2_spi6_sleep: blsp2-spi6-sleep-state {
				pins = "gpio85", "gpio86", "gpio87", "gpio88";
				function = "gpio";
				drive-strength = <2>;
				bias-pull-down;
			};

			blsp2_i2c6_default: blsp2-i2c6-state {
				pins = "gpio87", "gpio88";
				function = "blsp_i2c12";
				drive-strength = <16>;
				bias-disable;
			};

			blsp2_i2c6_sleep: blsp2-i2c6-sleep-state {
				pins = "gpio87", "gpio88";
				function = "gpio";
				drive-strength = <2>;
				bias-disable;
			};

			pcie1_state_on: pcie1-on-state {
				perst-pins {
					pins = "gpio130";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio131";
					function = "pci_e1";
					drive-strength = <2>;
					bias-pull-up;
				};

				wake-pins {
					pins = "gpio132";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};
			};

			pcie1_state_off: pcie1-off-state {
				/* Perst is missing? */
				clkreq-pins {
					pins = "gpio131";
					function = "gpio";
					drive-strength = <2>;
					bias-disable;
				};

				wake-pins {
					pins = "gpio132";
					function = "gpio";
					drive-strength = <2>;
					bias-disable;
				};
			};

			pcie2_state_on: pcie2-on-state {
				perst-pins {
					pins = "gpio114";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};

				clkreq-pins {
					pins = "gpio115";
					function = "pci_e2";
					drive-strength = <2>;
					bias-pull-up;
				};

				wake-pins {
					pins = "gpio116";
					function = "gpio";
					drive-strength = <2>;
					bias-pull-down;
				};
			};

			pcie2_state_off: pcie2-off-state {
				/* Perst is missing? */
				clkreq-pins {
					pins = "gpio115";
					function = "gpio";
					drive-strength = <2>;
					bias-disable;
				};

				wake-pins {
					pins = "gpio116";
					function = "gpio";
					drive-strength = <2>;
					bias-disable;
				};
			};

			sdc1_state_on: sdc1-on-state {
				clk-pins {
					pins = "sdc1_clk";
					bias-disable;
					drive-strength = <16>;
				};

				cmd-pins {
					pins = "sdc1_cmd";
					bias-pull-up;
					drive-strength = <10>;
				};

				data-pins {
					pins = "sdc1_data";
					bias-pull-up;
					drive-strength = <10>;
				};

				rclk-pins {
					pins = "sdc1_rclk";
					bias-pull-down;
				};
			};

			sdc1_state_off: sdc1-off-state {
				clk-pins {
					pins = "sdc1_clk";
					bias-disable;
					drive-strength = <2>;
				};

				cmd-pins {
					pins = "sdc1_cmd";
					bias-pull-up;
					drive-strength = <2>;
				};

				data-pins {
					pins = "sdc1_data";
					bias-pull-up;
					drive-strength = <2>;
				};

				rclk-pins {
					pins = "sdc1_rclk";
					bias-pull-down;
				};
			};

			sdc2_state_on: sdc2-on-state {
				clk-pins {
					pins = "sdc2_clk";
					bias-disable;
					drive-strength = <16>;
				};

				cmd-pins {
					pins = "sdc2_cmd";
					bias-pull-up;
					drive-strength = <10>;
				};

				data-pins {
					pins = "sdc2_data";
					bias-pull-up;
					drive-strength = <10>;
				};
			};

			sdc2_state_off: sdc2-off-state {
				clk-pins {
					pins = "sdc2_clk";
					bias-disable;
					drive-strength = <2>;
				};

				cmd-pins {
					pins = "sdc2_cmd";
					bias-pull-up;
					drive-strength = <2>;
				};

				data-pins {
					pins = "sdc2_data";
					bias-pull-up;
					drive-strength = <2>;
				};
			};
		};

		sram@290000 {
			compatible = "qcom,rpm-stats";
			reg = <0x00290000 0x10000>;
		};

		spmi_bus: spmi@400f000 {
			compatible = "qcom,spmi-pmic-arb";
			reg = <0x0400f000 0x1000>,
			      <0x04400000 0x800000>,
			      <0x04c00000 0x800000>,
			      <0x05800000 0x200000>,
			      <0x0400a000 0x002100>;
			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
			interrupt-names = "periph_irq";
			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			#address-cells = <2>;
			#size-cells = <0>;
			interrupt-controller;
			#interrupt-cells = <4>;
		};

		bus@0 {
			power-domains = <&gcc AGGRE0_NOC_GDSC>;
			compatible = "simple-pm-bus";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x0 0xffffffff>;

			pcie0: pcie@600000 {
				compatible = "qcom,pcie-msm8996";
				status = "disabled";
				power-domains = <&gcc PCIE0_GDSC>;
				bus-range = <0x00 0xff>;
				num-lanes = <1>;

				reg = <0x00600000 0x2000>,
				      <0x0c000000 0xf1d>,
				      <0x0c000f20 0xa8>,
				      <0x0c100000 0x100000>;
				reg-names = "parf", "dbi", "elbi","config";

				phys = <&pciephy_0>;
				phy-names = "pciephy";

				#address-cells = <3>;
				#size-cells = <2>;
				ranges = <0x01000000 0x0 0x00000000 0x0c200000 0x0 0x100000>,
					 <0x02000000 0x0 0x0c300000 0x0c300000 0x0 0xd00000>;

				device_type = "pci";

				interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names = "msi";
				#interrupt-cells = <1>;
				interrupt-map-mask = <0 0 0 0x7>;
				interrupt-map = <0 0 0 1 &intc 0 244 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
						<0 0 0 2 &intc 0 245 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
						<0 0 0 3 &intc 0 247 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
						<0 0 0 4 &intc 0 248 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

				pinctrl-names = "default", "sleep";
				pinctrl-0 = <&pcie0_state_on>;
				pinctrl-1 = <&pcie0_state_off>;

				linux,pci-domain = <0>;

				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
					<&gcc GCC_PCIE_0_AUX_CLK>,
					<&gcc GCC_PCIE_0_CFG_AHB_CLK>,
					<&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
					<&gcc GCC_PCIE_0_SLV_AXI_CLK>;

				clock-names = "pipe",
						"aux",
						"cfg",
						"bus_master",
						"bus_slave";

				pcie@0 {
					device_type = "pci";
					reg = <0x0 0x0 0x0 0x0 0x0>;
					bus-range = <0x01 0xff>;

					#address-cells = <3>;
					#size-cells = <2>;
					ranges;
				};
			};

			pcie1: pcie@608000 {
				compatible = "qcom,pcie-msm8996";
				power-domains = <&gcc PCIE1_GDSC>;
				bus-range = <0x00 0xff>;
				num-lanes = <1>;

				status = "disabled";

				reg = <0x00608000 0x2000>,
				      <0x0d000000 0xf1d>,
				      <0x0d000f20 0xa8>,
				      <0x0d100000 0x100000>;

				reg-names = "parf", "dbi", "elbi","config";

				phys = <&pciephy_1>;
				phy-names = "pciephy";

				#address-cells = <3>;
				#size-cells = <2>;
				ranges = <0x01000000 0x0 0x00000000 0x0d200000 0x0 0x100000>,
					 <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>;

				device_type = "pci";

				interrupts = <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names = "msi";
				#interrupt-cells = <1>;
				interrupt-map-mask = <0 0 0 0x7>;
				interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
						<0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
						<0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
						<0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

				pinctrl-names = "default", "sleep";
				pinctrl-0 = <&pcie1_state_on>;
				pinctrl-1 = <&pcie1_state_off>;

				linux,pci-domain = <1>;

				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
					<&gcc GCC_PCIE_1_AUX_CLK>,
					<&gcc GCC_PCIE_1_CFG_AHB_CLK>,
					<&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
					<&gcc GCC_PCIE_1_SLV_AXI_CLK>;

				clock-names = "pipe",
						"aux",
						"cfg",
						"bus_master",
						"bus_slave";

				pcie@0 {
					device_type = "pci";
					reg = <0x0 0x0 0x0 0x0 0x0>;
					bus-range = <0x01 0xff>;

					#address-cells = <3>;
					#size-cells = <2>;
					ranges;
				};
			};

			pcie2: pcie@610000 {
				compatible = "qcom,pcie-msm8996";
				power-domains = <&gcc PCIE2_GDSC>;
				bus-range = <0x00 0xff>;
				num-lanes = <1>;
				status = "disabled";
				reg = <0x00610000 0x2000>,
				      <0x0e000000 0xf1d>,
				      <0x0e000f20 0xa8>,
				      <0x0e100000 0x100000>;

				reg-names = "parf", "dbi", "elbi","config";

				phys = <&pciephy_2>;
				phy-names = "pciephy";

				#address-cells = <3>;
				#size-cells = <2>;
				ranges = <0x01000000 0x0 0x00000000 0x0e200000 0x0 0x100000>,
					 <0x02000000 0x0 0x0e300000 0x0e300000 0x0 0x1d00000>;

				device_type = "pci";

				interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names = "msi";
				#interrupt-cells = <1>;
				interrupt-map-mask = <0 0 0 0x7>;
				interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
						<0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
						<0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
						<0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

				pinctrl-names = "default", "sleep";
				pinctrl-0 = <&pcie2_state_on>;
				pinctrl-1 = <&pcie2_state_off>;

				linux,pci-domain = <2>;
				clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
					<&gcc GCC_PCIE_2_AUX_CLK>,
					<&gcc GCC_PCIE_2_CFG_AHB_CLK>,
					<&gcc GCC_PCIE_2_MSTR_AXI_CLK>,
					<&gcc GCC_PCIE_2_SLV_AXI_CLK>;

				clock-names = "pipe",
						"aux",
						"cfg",
						"bus_master",
						"bus_slave";

				pcie@0 {
					device_type = "pci";
					reg = <0x0 0x0 0x0 0x0 0x0>;
					bus-range = <0x01 0xff>;

					#address-cells = <3>;
					#size-cells = <2>;
					ranges;
				};
			};
		};

		ufshc: ufshc@624000 {
			compatible = "qcom,msm8996-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0x00624000 0x2500>;
			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;

			phys = <&ufsphy>;
			phy-names = "ufsphy";

			power-domains = <&gcc UFS_GDSC>;

			clock-names =
				"core_clk",
				"bus_clk",
				"bus_aggr_clk",
				"iface_clk",
				"core_clk_unipro",
				"core_clk_ice",
				"ref_clk",
				"tx_lane0_sync_clk",
				"rx_lane0_sync_clk";
			clocks =
				<&gcc GCC_UFS_AXI_CLK>,
				<&gcc GCC_SYS_NOC_UFS_AXI_CLK>,
				<&gcc GCC_AGGRE2_UFS_AXI_CLK>,
				<&gcc GCC_UFS_AHB_CLK>,
				<&gcc GCC_UFS_UNIPRO_CORE_CLK>,
				<&gcc GCC_UFS_ICE_CORE_CLK>,
				<&rpmcc RPM_SMD_LN_BB_CLK>,
				<&gcc GCC_UFS_TX_SYMBOL_0_CLK>,
				<&gcc GCC_UFS_RX_SYMBOL_0_CLK>;
			freq-table-hz =
				<100000000 200000000>,
				<0 0>,
				<0 0>,
				<0 0>,
				<75000000 150000000>,
				<150000000 300000000>,
				<0 0>,
				<0 0>,
				<0 0>;

			interconnects = <&a2noc MASTER_UFS &bimc SLAVE_EBI_CH0>,
					<&bimc MASTER_AMPSS_M0 &cnoc SLAVE_UFS_CFG>;
			interconnect-names = "ufs-ddr", "cpu-ufs";

			lanes-per-direction = <1>;
			#reset-cells = <1>;
			status = "disabled";
		};

		ufsphy: phy@627000 {
			compatible = "qcom,msm8996-qmp-ufs-phy";
			reg = <0x00627000 0x1000>;

			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>, <&gcc GCC_UFS_CLKREF_CLK>;
			clock-names = "ref", "qref";

			resets = <&ufshc 0>;
			reset-names = "ufsphy";

			#clock-cells = <1>;
			#phy-cells = <0>;

			status = "disabled";
		};

		camss: camss@a34000 {
			compatible = "qcom,msm8996-camss";
			reg = <0x00a34000 0x1000>,
			      <0x00a00030 0x4>,
			      <0x00a35000 0x1000>,
			      <0x00a00038 0x4>,
			      <0x00a36000 0x1000>,
			      <0x00a00040 0x4>,
			      <0x00a30000 0x100>,
			      <0x00a30400 0x100>,
			      <0x00a30800 0x100>,
			      <0x00a30c00 0x100>,
			      <0x00a31000 0x500>,
			      <0x00a00020 0x10>,
			      <0x00a10000 0x1000>,
			      <0x00a14000 0x1000>;
			reg-names = "csiphy0",
				"csiphy0_clk_mux",
				"csiphy1",
				"csiphy1_clk_mux",
				"csiphy2",
				"csiphy2_clk_mux",
				"csid0",
				"csid1",
				"csid2",
				"csid3",
				"ispif",
				"csi_clk_mux",
				"vfe0",
				"vfe1";
			interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 79 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 80 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 296 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 297 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 298 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 299 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 309 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 314 IRQ_TYPE_EDGE_RISING>,
				<GIC_SPI 315 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "csiphy0",
				"csiphy1",
				"csiphy2",
				"csid0",
				"csid1",
				"csid2",
				"csid3",
				"ispif",
				"vfe0",
				"vfe1";
			power-domains = <&mmcc VFE0_GDSC>,
					<&mmcc VFE1_GDSC>;
			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
				<&mmcc CAMSS_ISPIF_AHB_CLK>,
				<&mmcc CAMSS_CSI0PHYTIMER_CLK>,
				<&mmcc CAMSS_CSI1PHYTIMER_CLK>,
				<&mmcc CAMSS_CSI2PHYTIMER_CLK>,
				<&mmcc CAMSS_CSI0_AHB_CLK>,
				<&mmcc CAMSS_CSI0_CLK>,
				<&mmcc CAMSS_CSI0PHY_CLK>,
				<&mmcc CAMSS_CSI0PIX_CLK>,
				<&mmcc CAMSS_CSI0RDI_CLK>,
				<&mmcc CAMSS_CSI1_AHB_CLK>,
				<&mmcc CAMSS_CSI1_CLK>,
				<&mmcc CAMSS_CSI1PHY_CLK>,
				<&mmcc CAMSS_CSI1PIX_CLK>,
				<&mmcc CAMSS_CSI1RDI_CLK>,
				<&mmcc CAMSS_CSI2_AHB_CLK>,
				<&mmcc CAMSS_CSI2_CLK>,
				<&mmcc CAMSS_CSI2PHY_CLK>,
				<&mmcc CAMSS_CSI2PIX_CLK>,
				<&mmcc CAMSS_CSI2RDI_CLK>,
				<&mmcc CAMSS_CSI3_AHB_CLK>,
				<&mmcc CAMSS_CSI3_CLK>,
				<&mmcc CAMSS_CSI3PHY_CLK>,
				<&mmcc CAMSS_CSI3PIX_CLK>,
				<&mmcc CAMSS_CSI3RDI_CLK>,
				<&mmcc CAMSS_AHB_CLK>,
				<&mmcc CAMSS_VFE0_CLK>,
				<&mmcc CAMSS_CSI_VFE0_CLK>,
				<&mmcc CAMSS_VFE0_AHB_CLK>,
				<&mmcc CAMSS_VFE0_STREAM_CLK>,
				<&mmcc CAMSS_VFE1_CLK>,
				<&mmcc CAMSS_CSI_VFE1_CLK>,
				<&mmcc CAMSS_VFE1_AHB_CLK>,
				<&mmcc CAMSS_VFE1_STREAM_CLK>,
				<&mmcc CAMSS_VFE_AHB_CLK>,
				<&mmcc CAMSS_VFE_AXI_CLK>;
			clock-names = "top_ahb",
				"ispif_ahb",
				"csiphy0_timer",
				"csiphy1_timer",
				"csiphy2_timer",
				"csi0_ahb",
				"csi0",
				"csi0_phy",
				"csi0_pix",
				"csi0_rdi",
				"csi1_ahb",
				"csi1",
				"csi1_phy",
				"csi1_pix",
				"csi1_rdi",
				"csi2_ahb",
				"csi2",
				"csi2_phy",
				"csi2_pix",
				"csi2_rdi",
				"csi3_ahb",
				"csi3",
				"csi3_phy",
				"csi3_pix",
				"csi3_rdi",
				"ahb",
				"vfe0",
				"csi_vfe0",
				"vfe0_ahb",
				"vfe0_stream",
				"vfe1",
				"csi_vfe1",
				"vfe1_ahb",
				"vfe1_stream",
				"vfe_ahb",
				"vfe_axi";
			iommus = <&vfe_smmu 0>,
				 <&vfe_smmu 1>,
				 <&vfe_smmu 2>,
				 <&vfe_smmu 3>;
			status = "disabled";
			ports {
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		cci: cci@a0c000 {
			compatible = "qcom,msm8996-cci";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0xa0c000 0x1000>;
			interrupts = <GIC_SPI 295 IRQ_TYPE_EDGE_RISING>;
			power-domains = <&mmcc CAMSS_GDSC>;
			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
				 <&mmcc CAMSS_CCI_AHB_CLK>,
				 <&mmcc CAMSS_CCI_CLK>,
				 <&mmcc CAMSS_AHB_CLK>;
			clock-names = "camss_top_ahb",
				      "cci_ahb",
				      "cci",
				      "camss_ahb";
			assigned-clocks = <&mmcc CAMSS_CCI_AHB_CLK>,
					  <&mmcc CAMSS_CCI_CLK>;
			assigned-clock-rates = <80000000>, <37500000>;
			pinctrl-names = "default";
			pinctrl-0 = <&cci0_default &cci1_default>;
			status = "disabled";

			cci_i2c0: i2c-bus@0 {
				reg = <0>;
				clock-frequency = <400000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};

			cci_i2c1: i2c-bus@1 {
				reg = <1>;
				clock-frequency = <400000>;
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		adreno_smmu: iommu@b40000 {
			compatible = "qcom,msm8996-smmu-v2", "qcom,adreno-smmu", "qcom,smmu-v2";
			reg = <0x00b40000 0x10000>;

			#global-interrupts = <1>;
			interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
			#iommu-cells = <1>;

			clocks = <&gcc GCC_MMSS_BIMC_GFX_CLK>,
				 <&mmcc GPU_AHB_CLK>;
			clock-names = "bus", "iface";

			power-domains = <&mmcc GPU_GDSC>;
		};

		venus: video-codec@c00000 {
			compatible = "qcom,msm8996-venus";
			reg = <0x00c00000 0xff000>;
			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
			power-domains = <&mmcc VENUS_GDSC>;
			clocks = <&mmcc VIDEO_CORE_CLK>,
				 <&mmcc VIDEO_AHB_CLK>,
				 <&mmcc VIDEO_AXI_CLK>,
				 <&mmcc VIDEO_MAXI_CLK>;
			clock-names = "core", "iface", "bus", "mbus";
			interconnects = <&mnoc MASTER_VIDEO_P0 &bimc SLAVE_EBI_CH0>,
					<&bimc MASTER_AMPSS_M0 &mnoc SLAVE_VENUS_CFG>;
			interconnect-names = "video-mem", "cpu-cfg";
			iommus = <&venus_smmu 0x00>,
				 <&venus_smmu 0x01>,
				 <&venus_smmu 0x0a>,
				 <&venus_smmu 0x07>,
				 <&venus_smmu 0x0e>,
				 <&venus_smmu 0x0f>,
				 <&venus_smmu 0x08>,
				 <&venus_smmu 0x09>,
				 <&venus_smmu 0x0b>,
				 <&venus_smmu 0x0c>,
				 <&venus_smmu 0x0d>,
				 <&venus_smmu 0x10>,
				 <&venus_smmu 0x11>,
				 <&venus_smmu 0x21>,
				 <&venus_smmu 0x28>,
				 <&venus_smmu 0x29>,
				 <&venus_smmu 0x2b>,
				 <&venus_smmu 0x2c>,
				 <&venus_smmu 0x2d>,
				 <&venus_smmu 0x31>;
			memory-region = <&venus_mem>;
			status = "disabled";

			video-decoder {
				compatible = "venus-decoder";
				clocks = <&mmcc VIDEO_SUBCORE0_CLK>;
				clock-names = "core";
				power-domains = <&mmcc VENUS_CORE0_GDSC>;
			};

			video-encoder {
				compatible = "venus-encoder";
				clocks = <&mmcc VIDEO_SUBCORE1_CLK>;
				clock-names = "core";
				power-domains = <&mmcc VENUS_CORE1_GDSC>;
			};
		};

		mdp_smmu: iommu@d00000 {
			compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
			reg = <0x00d00000 0x10000>;

			#global-interrupts = <1>;
			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
			#iommu-cells = <1>;
			clocks = <&mmcc SMMU_MDP_AXI_CLK>,
				 <&mmcc SMMU_MDP_AHB_CLK>;
			clock-names = "bus", "iface";

			power-domains = <&mmcc MDSS_GDSC>;
		};

		venus_smmu: iommu@d40000 {
			compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
			reg = <0x00d40000 0x20000>;
			#global-interrupts = <1>;
			interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>;
			power-domains = <&mmcc MMAGIC_VIDEO_GDSC>;
			clocks = <&mmcc SMMU_VIDEO_AXI_CLK>,
				 <&mmcc SMMU_VIDEO_AHB_CLK>;
			clock-names = "bus", "iface";
			#iommu-cells = <1>;
			status = "okay";
		};

		vfe_smmu: iommu@da0000 {
			compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
			reg = <0x00da0000 0x10000>;

			#global-interrupts = <1>;
			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>;
			power-domains = <&mmcc MMAGIC_CAMSS_GDSC>;
			clocks = <&mmcc SMMU_VFE_AXI_CLK>,
				 <&mmcc SMMU_VFE_AHB_CLK>;
			clock-names = "bus", "iface";
			#iommu-cells = <1>;
		};

		lpass_q6_smmu: iommu@1600000 {
			compatible = "qcom,msm8996-smmu-v2", "qcom,smmu-v2";
			reg = <0x01600000 0x20000>;
			#iommu-cells = <1>;
			power-domains = <&gcc HLOS1_VOTE_LPASS_CORE_GDSC>;

			#global-interrupts = <1>;
			interrupts = <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
		                <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_HLOS1_VOTE_LPASS_ADSP_SMMU_CLK>,
				 <&gcc GCC_HLOS1_VOTE_LPASS_CORE_SMMU_CLK>;
			clock-names = "bus", "iface";
		};

		slpi_pil: remoteproc@1c00000 {
			compatible = "qcom,msm8996-slpi-pil";
			reg = <0x01c00000 0x4000>;

			interrupts-extended = <&intc 0 390 IRQ_TYPE_EDGE_RISING>,
					      <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog",
					  "fatal",
					  "ready",
					  "handover",
					  "stop-ack";

			clocks = <&xo_board>;
			clock-names = "xo";

			memory-region = <&slpi_mem>;

			qcom,smem-states = <&slpi_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			power-domains = <&rpmpd MSM8996_VDDSSCX>;
			power-domain-names = "ssc_cx";

			status = "disabled";

			glink-edge {
				interrupts = <GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
				label = "dsps";
				qcom,remote-pid = <3>;
				mboxes = <&apcs_glb 27>;
			};

			smd-edge {
				interrupts = <GIC_SPI 176 IRQ_TYPE_EDGE_RISING>;

				label = "dsps";
				mboxes = <&apcs_glb 25>;
				qcom,smd-edge = <3>;
				qcom,remote-pid = <3>;
			};
		};

		mss_pil: remoteproc@2080000 {
			compatible = "qcom,msm8996-mss-pil";
			reg = <0x2080000 0x100>,
			      <0x2180000 0x020>;
			reg-names = "qdsp6", "rmb";

			interrupts-extended = <&intc 0 448 IRQ_TYPE_EDGE_RISING>,
					      <&mpss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&mpss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&mpss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&mpss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
					      <&mpss_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack",
					  "shutdown-ack";

			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
				 <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
				 <&xo_board>,
				 <&gcc GCC_MSS_GPLL0_DIV_CLK>,
				 <&gcc GCC_MSS_SNOC_AXI_CLK>,
				 <&gcc GCC_MSS_MNOC_BIMC_AXI_CLK>,
				 <&rpmcc RPM_SMD_QDSS_CLK>;
			clock-names = "iface",
				      "bus",
				      "mem",
				      "xo",
				      "gpll0_mss",
				      "snoc_axi",
				      "mnoc_axi",
				      "qdss";

			resets = <&gcc GCC_MSS_RESTART>;
			reset-names = "mss_restart";

			power-domains = <&rpmpd MSM8996_VDDCX>,
					<&rpmpd MSM8996_VDDMX>;
			power-domain-names = "cx", "mx";

			qcom,smem-states = <&mpss_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			qcom,halt-regs = <&tcsr_1 0x3000 0x5000 0x4000>;

			status = "disabled";

			mba {
				memory-region = <&mba_mem>;
			};

			mpss {
				memory-region = <&mpss_mem>;
			};

			metadata {
				memory-region = <&mdata_mem>;
			};

			glink-edge {
				interrupts = <GIC_SPI 452 IRQ_TYPE_EDGE_RISING>;
				label = "modem";
				qcom,remote-pid = <1>;
				mboxes = <&apcs_glb 15>;
			};

			smd-edge {
				interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;

				label = "mpss";
				mboxes = <&apcs_glb 12>;
				qcom,smd-edge = <0>;
				qcom,remote-pid = <1>;
			};
		};

		stm@3002000 {
			compatible = "arm,coresight-stm", "arm,primecell";
			reg = <0x3002000 0x1000>,
			      <0x8280000 0x180000>;
			reg-names = "stm-base", "stm-stimulus-base";

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			out-ports {
				port {
					stm_out: endpoint {
						remote-endpoint =
						  <&funnel0_in>;
					};
				};
			};
		};

		tpiu@3020000 {
			compatible = "arm,coresight-tpiu", "arm,primecell";
			reg = <0x3020000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				port {
					tpiu_in: endpoint {
						remote-endpoint =
						  <&replicator_out1>;
					};
				};
			};
		};

		funnel@3021000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0x3021000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@7 {
					reg = <7>;
					funnel0_in: endpoint {
						remote-endpoint =
						  <&stm_out>;
					};
				};
			};

			out-ports {
				port {
					funnel0_out: endpoint {
						remote-endpoint =
						  <&merge_funnel_in0>;
					};
				};
			};
		};

		funnel@3022000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0x3022000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@6 {
					reg = <6>;
					funnel1_in: endpoint {
						remote-endpoint =
						  <&apss_merge_funnel_out>;
					};
				};
			};

			out-ports {
				port {
					funnel1_out: endpoint {
						remote-endpoint =
						  <&merge_funnel_in1>;
					};
				};
			};
		};

		funnel@3023000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0x3023000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				port {
					funnel_in2_in_modem_etm: endpoint {
						remote-endpoint =
						  <&modem_etm_out_funnel_in2>;
					};
				};
			};

			out-ports {
				port {
					funnel2_out: endpoint {
						remote-endpoint =
						  <&merge_funnel_in2>;
					};
				};
			};
		};

		funnel@3025000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0x3025000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					merge_funnel_in0: endpoint {
						remote-endpoint =
						  <&funnel0_out>;
					};
				};

				port@1 {
					reg = <1>;
					merge_funnel_in1: endpoint {
						remote-endpoint =
						  <&funnel1_out>;
					};
				};

				port@2 {
					reg = <2>;
					merge_funnel_in2: endpoint {
						remote-endpoint =
						  <&funnel2_out>;
					};
				};
			};

			out-ports {
				port {
					merge_funnel_out: endpoint {
						remote-endpoint =
						  <&etf_in>;
					};
				};
			};
		};

		replicator@3026000 {
			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
			reg = <0x3026000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				port {
					replicator_in: endpoint {
						remote-endpoint =
						  <&etf_out>;
					};
				};
			};

			out-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					replicator_out0: endpoint {
						remote-endpoint =
						  <&etr_in>;
					};
				};

				port@1 {
					reg = <1>;
					replicator_out1: endpoint {
						remote-endpoint =
						  <&tpiu_in>;
					};
				};
			};
		};

		etf@3027000 {
			compatible = "arm,coresight-tmc", "arm,primecell";
			reg = <0x3027000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				port {
					etf_in: endpoint {
						remote-endpoint =
						  <&merge_funnel_out>;
					};
				};
			};

			out-ports {
				port {
					etf_out: endpoint {
						remote-endpoint =
						  <&replicator_in>;
					};
				};
			};
		};

		etr@3028000 {
			compatible = "arm,coresight-tmc", "arm,primecell";
			reg = <0x3028000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";
			arm,scatter-gather;

			in-ports {
				port {
					etr_in: endpoint {
						remote-endpoint =
						  <&replicator_out0>;
					};
				};
			};
		};

		debug@3810000 {
			compatible = "arm,coresight-cpu-debug", "arm,primecell";
			reg = <0x3810000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			cpu = <&CPU0>;
		};

		etm@3840000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0x3840000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			cpu = <&CPU0>;

			out-ports {
				port {
					etm0_out: endpoint {
						remote-endpoint =
						  <&apss_funnel0_in0>;
					};
				};
			};
		};

		debug@3910000 {
			compatible = "arm,coresight-cpu-debug", "arm,primecell";
			reg = <0x3910000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			cpu = <&CPU1>;
		};

		etm@3940000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0x3940000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			cpu = <&CPU1>;

			out-ports {
				port {
					etm1_out: endpoint {
						remote-endpoint =
						  <&apss_funnel0_in1>;
					};
				};
			};
		};

		funnel@39b0000 { /* APSS Funnel 0 */
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0x39b0000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					apss_funnel0_in0: endpoint {
						remote-endpoint = <&etm0_out>;
					};
				};

				port@1 {
					reg = <1>;
					apss_funnel0_in1: endpoint {
						remote-endpoint = <&etm1_out>;
					};
				};
			};

			out-ports {
				port {
					apss_funnel0_out: endpoint {
						remote-endpoint =
						  <&apss_merge_funnel_in0>;
					};
				};
			};
		};

		debug@3a10000 {
			compatible = "arm,coresight-cpu-debug", "arm,primecell";
			reg = <0x3a10000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			cpu = <&CPU2>;
		};

		etm@3a40000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0x3a40000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			cpu = <&CPU2>;

			out-ports {
				port {
					etm2_out: endpoint {
						remote-endpoint =
						  <&apss_funnel1_in0>;
					};
				};
			};
		};

		debug@3b10000 {
			compatible = "arm,coresight-cpu-debug", "arm,primecell";
			reg = <0x3b10000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>;
			clock-names = "apb_pclk";

			cpu = <&CPU3>;
		};

		etm@3b40000 {
			compatible = "arm,coresight-etm4x", "arm,primecell";
			reg = <0x3b40000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			cpu = <&CPU3>;

			out-ports {
				port {
					etm3_out: endpoint {
						remote-endpoint =
						  <&apss_funnel1_in1>;
					};
				};
			};
		};

		funnel@3bb0000 { /* APSS Funnel 1 */
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0x3bb0000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					apss_funnel1_in0: endpoint {
						remote-endpoint = <&etm2_out>;
					};
				};

				port@1 {
					reg = <1>;
					apss_funnel1_in1: endpoint {
						remote-endpoint = <&etm3_out>;
					};
				};
			};

			out-ports {
				port {
					apss_funnel1_out: endpoint {
						remote-endpoint =
						  <&apss_merge_funnel_in1>;
					};
				};
			};
		};

		funnel@3bc0000 {
			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
			reg = <0x3bc0000 0x1000>;

			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
			clock-names = "apb_pclk", "atclk";

			in-ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;
					apss_merge_funnel_in0: endpoint {
						remote-endpoint =
						  <&apss_funnel0_out>;
					};
				};

				port@1 {
					reg = <1>;
					apss_merge_funnel_in1: endpoint {
						remote-endpoint =
						  <&apss_funnel1_out>;
					};
				};
			};

			out-ports {
				port {
					apss_merge_funnel_out: endpoint {
						remote-endpoint =
						  <&funnel1_in>;
					};
				};
			};
		};

		kryocc: clock-controller@6400000 {
			compatible = "qcom,msm8996-apcc";
			reg = <0x06400000 0x90000>;

			clock-names = "xo", "sys_apcs_aux";
			clocks = <&rpmcc RPM_SMD_XO_A_CLK_SRC>, <&apcs_glb>;

			#clock-cells = <1>;
		};

		usb3: usb@6af8800 {
			compatible = "qcom,msm8996-dwc3", "qcom,dwc3";
			reg = <0x06af8800 0x400>;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hs_phy_irq", "ss_phy_irq";

			clocks = <&gcc GCC_SYS_NOC_USB3_AXI_CLK>,
				 <&gcc GCC_USB30_MASTER_CLK>,
				 <&gcc GCC_AGGRE2_USB3_AXI_CLK>,
				 <&gcc GCC_USB30_SLEEP_CLK>,
				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi";

			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <120000000>;

			interconnects = <&a2noc MASTER_USB3 &bimc SLAVE_EBI_CH0>,
					<&bimc MASTER_AMPSS_M0 &snoc SLAVE_USB3>;
			interconnect-names = "usb-ddr", "apps-usb";

			power-domains = <&gcc USB30_GDSC>;
			status = "disabled";

			usb3_dwc3: usb@6a00000 {
				compatible = "snps,dwc3";
				reg = <0x06a00000 0xcc00>;
				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
				phys = <&hsusb_phy1>, <&usb3phy>;
				phy-names = "usb2-phy", "usb3-phy";
				snps,hird-threshold = /bits/ 8 <0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				snps,is-utmi-l1-suspend;
				snps,parkmode-disable-ss-quirk;
				tx-fifo-resize;
			};
		};

		usb3phy: phy@7410000 {
			compatible = "qcom,msm8996-qmp-usb3-phy";
			reg = <0x07410000 0x1000>;

			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
				 <&gcc GCC_USB3_CLKREF_CLK>,
				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
				 <&gcc GCC_USB3_PHY_PIPE_CLK>;
			clock-names = "aux",
				      "ref",
				      "cfg_ahb",
				      "pipe";
			clock-output-names = "usb3_phy_pipe_clk_src";
			#clock-cells = <0>;
			#phy-cells = <0>;

			resets = <&gcc GCC_USB3_PHY_BCR>,
				 <&gcc GCC_USB3PHY_PHY_BCR>;
			reset-names = "phy",
				      "phy_phy";

			status = "disabled";
		};

		hsusb_phy1: phy@7411000 {
			compatible = "qcom,msm8996-qusb2-phy";
			reg = <0x07411000 0x180>;
			#phy-cells = <0>;

			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
				<&gcc GCC_RX1_USB2_CLKREF_CLK>;
			clock-names = "cfg_ahb", "ref";

			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
			nvmem-cells = <&qusb2p_hstx_trim>;
			status = "disabled";
		};

		hsusb_phy2: phy@7412000 {
			compatible = "qcom,msm8996-qusb2-phy";
			reg = <0x07412000 0x180>;
			#phy-cells = <0>;

			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
				<&gcc GCC_RX2_USB2_CLKREF_CLK>;
			clock-names = "cfg_ahb", "ref";

			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
			nvmem-cells = <&qusb2s_hstx_trim>;
			status = "disabled";
		};

		sdhc1: mmc@7464900 {
			compatible = "qcom,msm8996-sdhci", "qcom,sdhci-msm-v4";
			reg = <0x07464900 0x11c>, <0x07464000 0x800>;
			reg-names = "hc", "core";

			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
					<GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";

			clock-names = "iface", "core", "xo";
			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
				<&gcc GCC_SDCC1_APPS_CLK>,
				<&rpmcc RPM_SMD_XO_CLK_SRC>;
			resets = <&gcc GCC_SDCC1_BCR>;

			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&sdc1_state_on>;
			pinctrl-1 = <&sdc1_state_off>;

			bus-width = <8>;
			non-removable;
			status = "disabled";
		};

		sdhc2: mmc@74a4900 {
			compatible = "qcom,msm8996-sdhci", "qcom,sdhci-msm-v4";
			reg = <0x074a4900 0x314>, <0x074a4000 0x800>;
			reg-names = "hc", "core";

			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
				      <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";

			clock-names = "iface", "core", "xo";
			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
				<&gcc GCC_SDCC2_APPS_CLK>,
				<&rpmcc RPM_SMD_XO_CLK_SRC>;
			resets = <&gcc GCC_SDCC2_BCR>;

			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&sdc2_state_on>;
			pinctrl-1 = <&sdc2_state_off>;

			bus-width = <4>;
			status = "disabled";
		 };

		blsp1_dma: dma-controller@7544000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x07544000 0x2b000>;
			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "bam_clk";
			qcom,controlled-remotely;
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		blsp1_uart2: serial@7570000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0x07570000 0x1000>;
			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp1_uart2_default>;
			pinctrl-1 = <&blsp1_uart2_sleep>;
			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		blsp1_spi1: spi@7575000 {
			compatible = "qcom,spi-qup-v2.2.1";
			reg = <0x07575000 0x600>;
			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp1_spi1_default>;
			pinctrl-1 = <&blsp1_spi1_sleep>;
			dmas = <&blsp1_dma 12>, <&blsp1_dma 13>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		blsp1_i2c3: i2c@7577000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			reg = <0x07577000 0x1000>;
			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp1_i2c3_default>;
			pinctrl-1 = <&blsp1_i2c3_sleep>;
			dmas = <&blsp1_dma 16>, <&blsp1_dma 17>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		blsp1_i2c6: i2c@757a000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			reg = <0x757a000 0x1000>;
			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp1_i2c6_default>;
			pinctrl-1 = <&blsp1_i2c6_sleep>;
			dmas = <&blsp1_dma 22>, <&blsp1_dma 23>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		blsp2_dma: dma-controller@7584000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x07584000 0x2b000>;
			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "bam_clk";
			qcom,controlled-remotely;
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		blsp2_uart2: serial@75b0000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0x075b0000 0x1000>;
			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>,
				 <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			status = "disabled";
		};

		blsp2_uart3: serial@75b1000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0x075b1000 0x1000>;
			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_UART3_APPS_CLK>,
				 <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			status = "disabled";
		};

		blsp2_i2c1: i2c@75b5000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			reg = <0x075b5000 0x1000>;
			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_i2c1_default>;
			pinctrl-1 = <&blsp2_i2c1_sleep>;
			dmas = <&blsp2_dma 12>, <&blsp2_dma 13>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		blsp2_i2c2: i2c@75b6000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			reg = <0x075b6000 0x1000>;
			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_i2c2_default>;
			pinctrl-1 = <&blsp2_i2c2_sleep>;
			dmas = <&blsp2_dma 14>, <&blsp2_dma 15>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		blsp2_i2c3: i2c@75b7000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			reg = <0x075b7000 0x1000>;
			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			clock-frequency = <400000>;
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_i2c3_default>;
			pinctrl-1 = <&blsp2_i2c3_sleep>;
			dmas = <&blsp2_dma 16>, <&blsp2_dma 17>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		blsp2_i2c5: i2c@75b9000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			reg = <0x75b9000 0x1000>;
			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default";
			pinctrl-0 = <&blsp2_i2c5_default>;
			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		blsp2_i2c6: i2c@75ba000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			reg = <0x75ba000 0x1000>;
			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_i2c6_default>;
			pinctrl-1 = <&blsp2_i2c6_sleep>;
			dmas = <&blsp2_dma 22>, <&blsp2_dma 23>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		blsp2_spi6: spi@75ba000 {
			compatible = "qcom,spi-qup-v2.2.1";
			reg = <0x075ba000 0x600>;
			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP2_QUP6_SPI_APPS_CLK>,
				 <&gcc GCC_BLSP2_AHB_CLK>;
			clock-names = "core", "iface";
			pinctrl-names = "default", "sleep";
			pinctrl-0 = <&blsp2_spi6_default>;
			pinctrl-1 = <&blsp2_spi6_sleep>;
			dmas = <&blsp2_dma 22>, <&blsp2_dma 23>;
			dma-names = "tx", "rx";
			#address-cells = <1>;
			#size-cells = <0>;
			status = "disabled";
		};

		usb2: usb@76f8800 {
			compatible = "qcom,msm8996-dwc3", "qcom,dwc3";
			reg = <0x076f8800 0x400>;
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "pwr_event",
					  "qusb2_phy",
					  "hs_phy_irq";

			clocks = <&gcc GCC_PERIPH_NOC_USB20_AHB_CLK>,
				<&gcc GCC_USB20_MASTER_CLK>,
				<&gcc GCC_USB20_MOCK_UTMI_CLK>,
				<&gcc GCC_USB20_SLEEP_CLK>,
				<&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi";

			assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB20_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <60000000>;

			power-domains = <&gcc USB30_GDSC>;
			qcom,select-utmi-as-pipe-clk;
			status = "disabled";

			usb2_dwc3: usb@7600000 {
				compatible = "snps,dwc3";
				reg = <0x07600000 0xcc00>;
				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
				phys = <&hsusb_phy2>;
				phy-names = "usb2-phy";
				maximum-speed = "high-speed";
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
			};
		};

		slimbam: dma-controller@9184000 {
			compatible = "qcom,bam-v1.7.0";
			qcom,controlled-remotely;
			reg = <0x09184000 0x32000>;
			num-channels = <31>;
			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
			#dma-cells = <1>;
			qcom,ee = <1>;
			qcom,num-ees = <2>;
		};

		slim_msm: slim-ngd@91c0000 {
			compatible = "qcom,slim-ngd-v1.5.0";
			reg = <0x091c0000 0x2c000>;
			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
			dmas = <&slimbam 3>, <&slimbam 4>;
			dma-names = "rx", "tx";
			#address-cells = <1>;
			#size-cells = <0>;

			status = "disabled";
		};

		adsp_pil: remoteproc@9300000 {
			compatible = "qcom,msm8996-adsp-pil";
			reg = <0x09300000 0x80000>;

			interrupts-extended = <&intc 0 162 IRQ_TYPE_EDGE_RISING>,
					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
			clock-names = "xo";

			memory-region = <&adsp_mem>;

			qcom,smem-states = <&adsp_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			power-domains = <&rpmpd MSM8996_VDDCX>;
			power-domain-names = "cx";

			status = "disabled";

			glink-edge {
				interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
				label = "lpass";
				qcom,remote-pid = <2>;
				mboxes = <&apcs_glb 9>;
			};


			smd-edge {
				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;

				label = "lpass";
				mboxes = <&apcs_glb 8>;
				qcom,smd-edge = <1>;
				qcom,remote-pid = <2>;

				apr {
					power-domains = <&gcc HLOS1_VOTE_LPASS_ADSP_GDSC>;
					compatible = "qcom,apr-v2";
					qcom,smd-channels = "apr_audio_svc";
					qcom,domain = <APR_DOMAIN_ADSP>;
					#address-cells = <1>;
					#size-cells = <0>;

					service@3 {
						reg = <APR_SVC_ADSP_CORE>;
						compatible = "qcom,q6core";
					};

					q6afe: service@4 {
						compatible = "qcom,q6afe";
						reg = <APR_SVC_AFE>;
						q6afedai: dais {
							compatible = "qcom,q6afe-dais";
							#address-cells = <1>;
							#size-cells = <0>;
							#sound-dai-cells = <1>;
							dai@1 {
								reg = <1>;
							};
						};
					};

					q6asm: service@7 {
						compatible = "qcom,q6asm";
						reg = <APR_SVC_ASM>;
						q6asmdai: dais {
							compatible = "qcom,q6asm-dais";
							#address-cells = <1>;
							#size-cells = <0>;
							#sound-dai-cells = <1>;
							iommus = <&lpass_q6_smmu 1>;
						};
					};

					q6adm: service@8 {
						compatible = "qcom,q6adm";
						reg = <APR_SVC_ADM>;
						q6routing: routing {
							compatible = "qcom,q6adm-routing";
							#sound-dai-cells = <0>;
						};
					};
				};

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,smd-channels = "fastrpcsmd-apps-dsp";
					label = "adsp";
					qcom,non-secure-domain;
					#address-cells = <1>;
					#size-cells = <0>;

					cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&lpass_q6_smmu 5>;
					};

					cb@6 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <6>;
						iommus = <&lpass_q6_smmu 6>;
					};

					cb@7 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <7>;
						iommus = <&lpass_q6_smmu 7>;
					};

					cb@8 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <8>;
						iommus = <&lpass_q6_smmu 8>;
					};

					cb@9 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <9>;
						iommus = <&lpass_q6_smmu 9>;
					};

					cb@10 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <10>;
						iommus = <&lpass_q6_smmu 10>;
					};

					cb@11 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <11>;
						iommus = <&lpass_q6_smmu 11>;
					};

					cb@12 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <12>;
						iommus = <&lpass_q6_smmu 12>;
					};
				};
			};
		};

		apcs_glb: mailbox@9820000 {
			compatible = "qcom,msm8996-apcs-hmss-global";
			reg = <0x09820000 0x1000>;

			#mbox-cells = <1>;
			#clock-cells = <0>;
		};

		timer@9840000 {
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			compatible = "arm,armv7-timer-mem";
			reg = <0x09840000 0x1000>;
			clock-frequency = <19200000>;

			frame@9850000 {
				frame-number = <0>;
				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x09850000 0x1000>,
				      <0x09860000 0x1000>;
			};

			frame@9870000 {
				frame-number = <1>;
				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x09870000 0x1000>;
				status = "disabled";
			};

			frame@9880000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x09880000 0x1000>;
				status = "disabled";
			};

			frame@9890000 {
				frame-number = <3>;
				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x09890000 0x1000>;
				status = "disabled";
			};

			frame@98a0000 {
				frame-number = <4>;
				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x098a0000 0x1000>;
				status = "disabled";
			};

			frame@98b0000 {
				frame-number = <5>;
				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x098b0000 0x1000>;
				status = "disabled";
			};

			frame@98c0000 {
				frame-number = <6>;
				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x098c0000 0x1000>;
				status = "disabled";
			};
		};

		saw3: syscon@9a10000 {
			compatible = "syscon";
			reg = <0x09a10000 0x1000>;
		};

		cbf: clock-controller@9a11000 {
			compatible = "qcom,msm8996-cbf";
			reg = <0x09a11000 0x10000>;
			clocks = <&rpmcc RPM_SMD_XO_A_CLK_SRC>, <&apcs_glb>;
			#clock-cells = <0>;
			#interconnect-cells = <1>;
		};

		intc: interrupt-controller@9bc0000 {
			compatible = "qcom,msm8996-gic-v3", "arm,gic-v3";
			#interrupt-cells = <3>;
			interrupt-controller;
			#redistributor-regions = <1>;
			redistributor-stride = <0x0 0x40000>;
			reg = <0x09bc0000 0x10000>,
			      <0x09c00000 0x100000>;
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
		};
	};

	sound: sound {
	};

	thermal-zones {
		cpu0-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 3>;

			trips {
				cpu0_alert0: trip-point0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 5>;

			trips {
				cpu1_alert0: trip-point0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 8>;

			trips {
				cpu2_alert0: trip-point0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cpu3-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 10>;

			trips {
				cpu3_alert0: trip-point0 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		gpu-top-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens1 6>;

			trips {
				gpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};
			};

			cooling-maps {
				map0 {
					trip = <&gpu1_alert0>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		gpu-bottom-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens1 7>;

			trips {
				gpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};
			};

			cooling-maps {
				map0 {
					trip = <&gpu2_alert0>;
					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		m4m-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 1>;

			trips {
				m4m_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		l3-or-venus-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 2>;

			trips {
				l3_or_venus_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		cluster0-l2-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 7>;

			trips {
				cluster0_l2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		cluster1-l2-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens0 12>;

			trips {
				cluster1_l2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		camera-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens1 1>;

			trips {
				camera_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		q6-dsp-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens1 2>;

			trips {
				q6_dsp_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		mem-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens1 3>;

			trips {
				mem_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		modemtx-thermal {
			polling-delay-passive = <250>;

			thermal-sensors = <&tsens1 4>;

			trips {
				modemtx_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
	};
};