// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/gpio-keys.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>

#include "x1e80100.dtsi"
#include "x1e80100-pmics.dtsi"

/ {
	model = "Qualcomm Technologies, Inc. X1E80100 CRD";
	compatible = "qcom,x1e80100-crd", "qcom,x1e80100";

	aliases {
		serial0 = &uart21;
	};

	wcd938x: audio-codec {
		compatible = "qcom,wcd9385-codec";

		pinctrl-names = "default";
		pinctrl-0 = <&wcd_default>;

		qcom,micbias1-microvolt = <1800000>;
		qcom,micbias2-microvolt = <1800000>;
		qcom,micbias3-microvolt = <1800000>;
		qcom,micbias4-microvolt = <1800000>;
		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
		qcom,rx-device = <&wcd_rx>;
		qcom,tx-device = <&wcd_tx>;

		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;

		vdd-buck-supply = <&vreg_l15b_1p8>;
		vdd-rxtx-supply = <&vreg_l15b_1p8>;
		vdd-io-supply = <&vreg_l15b_1p8>;
		vdd-mic-bias-supply = <&vreg_bob1>;

		#sound-dai-cells = <1>;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	gpio-keys {
		compatible = "gpio-keys";

		pinctrl-0 = <&hall_int_n_default>;
		pinctrl-names = "default";

		switch-lid {
			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
			linux,input-type = <EV_SW>;
			linux,code = <SW_LID>;
			wakeup-source;
			wakeup-event-action = <EV_ACT_DEASSERTED>;
		};
	};

	pmic-glink {
		compatible = "qcom,x1e80100-pmic-glink",
			     "qcom,sm8550-pmic-glink",
			     "qcom,pmic-glink";
		#address-cells = <1>;
		#size-cells = <0>;
		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
				    <&tlmm 125 GPIO_ACTIVE_HIGH>;

		/* Left-side rear port */
		connector@0 {
			compatible = "usb-c-connector";
			reg = <0>;
			power-role = "dual";
			data-role = "dual";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;

					pmic_glink_ss0_hs_in: endpoint {
						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
					};
				};

				port@1 {
					reg = <1>;

					pmic_glink_ss0_ss_in: endpoint {
						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
					};
				};
			};
		};

		/* Left-side front port */
		connector@1 {
			compatible = "usb-c-connector";
			reg = <1>;
			power-role = "dual";
			data-role = "dual";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;

					pmic_glink_ss1_hs_in: endpoint {
						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
					};
				};

				port@1 {
					reg = <1>;

					pmic_glink_ss1_ss_in: endpoint {
						remote-endpoint = <&usb_1_ss1_qmpphy_out>;
					};
				};
			};
		};

		/* Right-side port */
		connector@2 {
			compatible = "usb-c-connector";
			reg = <2>;
			power-role = "dual";
			data-role = "dual";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;

					pmic_glink_ss2_hs_in: endpoint {
						remote-endpoint = <&usb_1_ss2_dwc3_hs>;
					};
				};

				port@1 {
					reg = <1>;

					pmic_glink_ss2_ss_in: endpoint {
						remote-endpoint = <&usb_1_ss2_qmpphy_out>;
					};
				};
			};
		};
	};

	reserved-memory {
		linux,cma {
			compatible = "shared-dma-pool";
			size = <0x0 0x8000000>;
			reusable;
			linux,cma-default;
		};
	};

	sound {
		compatible = "qcom,x1e80100-sndcard";
		model = "X1E80100-CRD";
		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
				"IN1_HPHL", "HPHL_OUT",
				"IN2_HPHR", "HPHR_OUT",
				"AMIC2", "MIC BIAS2",
				"VA DMIC0", "MIC BIAS3",
				"VA DMIC1", "MIC BIAS3",
				"VA DMIC2", "MIC BIAS1",
				"VA DMIC3", "MIC BIAS1",
				"VA DMIC0", "VA MIC BIAS3",
				"VA DMIC1", "VA MIC BIAS3",
				"VA DMIC2", "VA MIC BIAS1",
				"VA DMIC3", "VA MIC BIAS1",
				"TX SWR_INPUT1", "ADC2_OUTPUT";

		wcd-playback-dai-link {
			link-name = "WCD Playback";

			cpu {
				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
			};

			codec {
				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
			};

			platform {
				sound-dai = <&q6apm>;
			};
		};

		wcd-capture-dai-link {
			link-name = "WCD Capture";

			cpu {
				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
			};

			codec {
				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
			};

			platform {
				sound-dai = <&q6apm>;
			};
		};

		wsa-dai-link {
			link-name = "WSA Playback";

			cpu {
				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
			};

			codec {
				sound-dai = <&left_woofer>, <&left_tweeter>,
					    <&swr0 0>, <&lpass_wsamacro 0>,
					    <&right_woofer>, <&right_tweeter>,
					    <&swr3 0>, <&lpass_wsa2macro 0>;
			};

			platform {
				sound-dai = <&q6apm>;
			};
		};

		va-dai-link {
			link-name = "VA Capture";

			cpu {
				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
			};

			codec {
				sound-dai = <&lpass_vamacro 0>;
			};

			platform {
				sound-dai = <&q6apm>;
			};
		};
	};

	vph_pwr: vph-pwr-regulator {
		compatible = "regulator-fixed";

		regulator-name = "vph_pwr";
		regulator-min-microvolt = <3700000>;
		regulator-max-microvolt = <3700000>;

		regulator-always-on;
		regulator-boot-on;
	};

	vreg_edp_3p3: regulator-edp-3p3 {
		compatible = "regulator-fixed";

		regulator-name = "VREG_EDP_3P3";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;

		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
		enable-active-high;

		pinctrl-0 = <&edp_reg_en>;
		pinctrl-names = "default";

		regulator-boot-on;
	};

	vreg_nvme: regulator-nvme {
		compatible = "regulator-fixed";

		regulator-name = "VREG_NVME_3P3";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;

		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
		enable-active-high;

		pinctrl-names = "default";
		pinctrl-0 = <&nvme_reg_en>;

		regulator-boot-on;
	};

	vreg_wwan: regulator-wwan {
		compatible = "regulator-fixed";

		regulator-name = "SDX_VPH_PWR";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;

		gpio = <&tlmm 221 GPIO_ACTIVE_HIGH>;
		enable-active-high;

		pinctrl-0 = <&wwan_sw_en>;
		pinctrl-names = "default";

		regulator-boot-on;
	};
};

&apps_rsc {
	regulators-0 {
		compatible = "qcom,pm8550-rpmh-regulators";
		qcom,pmic-id = "b";

		vdd-bob1-supply = <&vph_pwr>;
		vdd-bob2-supply = <&vph_pwr>;
		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
		vdd-l2-l13-l14-supply = <&vreg_bob1>;
		vdd-l5-l16-supply = <&vreg_bob1>;
		vdd-l6-l7-supply = <&vreg_bob2>;
		vdd-l8-l9-supply = <&vreg_bob1>;
		vdd-l12-supply = <&vreg_s5j_1p2>;
		vdd-l15-supply = <&vreg_s4c_1p8>;
		vdd-l17-supply = <&vreg_bob2>;

		vreg_bob1: bob1 {
			regulator-name = "vreg_bob1";
			regulator-min-microvolt = <3008000>;
			regulator-max-microvolt = <3960000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_bob2: bob2 {
			regulator-name = "vreg_bob2";
			regulator-min-microvolt = <2504000>;
			regulator-max-microvolt = <3008000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1b_1p8: ldo1 {
			regulator-name = "vreg_l1b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2b_3p0: ldo2 {
			regulator-name = "vreg_l2b_3p0";
			regulator-min-microvolt = <3072000>;
			regulator-max-microvolt = <3100000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l4b_1p8: ldo4 {
			regulator-name = "vreg_l4b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l5b_3p0: ldo5 {
			regulator-name = "vreg_l5b_3p0";
			regulator-min-microvolt = <3000000>;
			regulator-max-microvolt = <3000000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l6b_1p8: ldo6 {
			regulator-name = "vreg_l6b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <2960000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l7b_2p8: ldo7 {
			regulator-name = "vreg_l7b_2p8";
			regulator-min-microvolt = <2800000>;
			regulator-max-microvolt = <2800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l8b_3p0: ldo8 {
			regulator-name = "vreg_l8b_3p0";
			regulator-min-microvolt = <3072000>;
			regulator-max-microvolt = <3072000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l9b_2p9: ldo9 {
			regulator-name = "vreg_l9b_2p9";
			regulator-min-microvolt = <2960000>;
			regulator-max-microvolt = <2960000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l10b_1p8: ldo10 {
			regulator-name = "vreg_l10b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l12b_1p2: ldo12 {
			regulator-name = "vreg_l12b_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l13b_3p0: ldo13 {
			regulator-name = "vreg_l13b_3p0";
			regulator-min-microvolt = <3072000>;
			regulator-max-microvolt = <3100000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l14b_3p0: ldo14 {
			regulator-name = "vreg_l14b_3p0";
			regulator-min-microvolt = <3072000>;
			regulator-max-microvolt = <3072000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l15b_1p8: ldo15 {
			regulator-name = "vreg_l15b_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l16b_2p9: ldo16 {
			regulator-name = "vreg_l16b_2p9";
			regulator-min-microvolt = <2912000>;
			regulator-max-microvolt = <2912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l17b_2p5: ldo17 {
			regulator-name = "vreg_l17b_2p5";
			regulator-min-microvolt = <2504000>;
			regulator-max-microvolt = <2504000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-1 {
		compatible = "qcom,pm8550ve-rpmh-regulators";
		qcom,pmic-id = "c";

		vdd-l1-supply = <&vreg_s5j_1p2>;
		vdd-l2-supply = <&vreg_s1f_0p7>;
		vdd-l3-supply = <&vreg_s1f_0p7>;
		vdd-s4-supply = <&vph_pwr>;

		vreg_s4c_1p8: smps4 {
			regulator-name = "vreg_s4c_1p8";
			regulator-min-microvolt = <1856000>;
			regulator-max-microvolt = <2000000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1c_1p2: ldo1 {
			regulator-name = "vreg_l1c_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2c_0p8: ldo2 {
			regulator-name = "vreg_l2c_0p8";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3c_0p8: ldo3 {
			regulator-name = "vreg_l3c_0p8";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-2 {
		compatible = "qcom,pmc8380-rpmh-regulators";
		qcom,pmic-id = "d";

		vdd-l1-supply = <&vreg_s1f_0p7>;
		vdd-l2-supply = <&vreg_s1f_0p7>;
		vdd-l3-supply = <&vreg_s4c_1p8>;
		vdd-s1-supply = <&vph_pwr>;

		vreg_l1d_0p8: ldo1 {
			regulator-name = "vreg_l1d_0p8";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2d_0p9: ldo2 {
			regulator-name = "vreg_l2d_0p9";
			regulator-min-microvolt = <912000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3d_1p8: ldo3 {
			regulator-name = "vreg_l3d_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-3 {
		compatible = "qcom,pmc8380-rpmh-regulators";
		qcom,pmic-id = "e";

		vdd-l2-supply = <&vreg_s1f_0p7>;
		vdd-l3-supply = <&vreg_s5j_1p2>;

		vreg_l2e_0p8: ldo2 {
			regulator-name = "vreg_l2e_0p8";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3e_1p2: ldo3 {
			regulator-name = "vreg_l3e_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-4 {
		compatible = "qcom,pmc8380-rpmh-regulators";
		qcom,pmic-id = "f";

		vdd-l1-supply = <&vreg_s5j_1p2>;
		vdd-l2-supply = <&vreg_s5j_1p2>;
		vdd-l3-supply = <&vreg_s5j_1p2>;
		vdd-s1-supply = <&vph_pwr>;

		vreg_s1f_0p7: smps1 {
			regulator-name = "vreg_s1f_0p7";
			regulator-min-microvolt = <700000>;
			regulator-max-microvolt = <1100000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1f_1p0: ldo1 {
			regulator-name = "vreg_l1f_1p0";
			regulator-min-microvolt = <1024000>;
			regulator-max-microvolt = <1024000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2f_1p0: ldo2 {
			regulator-name = "vreg_l2f_1p0";
			regulator-min-microvolt = <1024000>;
			regulator-max-microvolt = <1024000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3f_1p0: ldo3 {
			regulator-name = "vreg_l3f_1p0";
			regulator-min-microvolt = <1024000>;
			regulator-max-microvolt = <1024000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-6 {
		compatible = "qcom,pm8550ve-rpmh-regulators";
		qcom,pmic-id = "i";

		vdd-l1-supply = <&vreg_s4c_1p8>;
		vdd-l2-supply = <&vreg_s5j_1p2>;
		vdd-l3-supply = <&vreg_s1f_0p7>;
		vdd-s1-supply = <&vph_pwr>;
		vdd-s2-supply = <&vph_pwr>;

		vreg_s1i_0p9: smps1 {
			regulator-name = "vreg_s1i_0p9";
			regulator-min-microvolt = <900000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_s2i_1p0: smps2 {
			regulator-name = "vreg_s2i_1p0";
			regulator-min-microvolt = <1000000>;
			regulator-max-microvolt = <1100000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1i_1p8: ldo1 {
			regulator-name = "vreg_l1i_1p8";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2i_1p2: ldo2 {
			regulator-name = "vreg_l2i_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3i_0p8: ldo3 {
			regulator-name = "vreg_l3i_0p8";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};
	};

	regulators-7 {
		compatible = "qcom,pm8550ve-rpmh-regulators";
		qcom,pmic-id = "j";

		vdd-l1-supply = <&vreg_s1f_0p7>;
		vdd-l2-supply = <&vreg_s5j_1p2>;
		vdd-l3-supply = <&vreg_s1f_0p7>;
		vdd-s5-supply = <&vph_pwr>;

		vreg_s5j_1p2: smps5 {
			regulator-name = "vreg_s5j_1p2";
			regulator-min-microvolt = <1256000>;
			regulator-max-microvolt = <1304000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l1j_0p8: ldo1 {
			regulator-name = "vreg_l1j_0p8";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l2j_1p2: ldo2 {
			regulator-name = "vreg_l2j_1p2";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3j_0p8: ldo3 {
			regulator-name = "vreg_l3j_0p8";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <920000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};
	};
};

&gpu {
	status = "okay";

	zap-shader {
		firmware-name = "qcom/x1e80100/gen70500_zap.mbn";
	};
};

&i2c0 {
	clock-frequency = <400000>;

	status = "okay";

	touchpad@15 {
		compatible = "hid-over-i2c";
		reg = <0x15>;

		hid-descr-addr = <0x1>;
		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;

		pinctrl-0 = <&tpad_default>;
		pinctrl-names = "default";

		wakeup-source;
	};

	keyboard@3a {
		compatible = "hid-over-i2c";
		reg = <0x3a>;

		hid-descr-addr = <0x1>;
		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;

		pinctrl-0 = <&kybd_default>;
		pinctrl-names = "default";

		wakeup-source;
	};
};

&i2c8 {
	clock-frequency = <400000>;

	status = "okay";

	touchscreen@10 {
		compatible = "hid-over-i2c";
		reg = <0x10>;

		hid-descr-addr = <0x1>;
		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;

		pinctrl-0 = <&ts0_default>;
		pinctrl-names = "default";
	};
};

&lpass_tlmm {
	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
		pins = "gpio12";
		function = "gpio";
		drive-strength = <16>;
		bias-disable;
		output-low;
	};

	spkr_23_sd_n_active: spkr-23-sd-n-active-state {
		pins = "gpio13";
		function = "gpio";
		drive-strength = <16>;
		bias-disable;
		output-low;
	};
};

&lpass_vamacro {
	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
	pinctrl-names = "default";

	vdd-micb-supply = <&vreg_l1b_1p8>;
	qcom,dmic-sample-rate = <4800000>;
};

&mdss {
	status = "okay";
};

&mdss_dp3 {
	compatible = "qcom,x1e80100-dp";
	/delete-property/ #sound-dai-cells;

	status = "okay";

	aux-bus {
		panel {
			compatible = "samsung,atna45af01", "samsung,atna33xc20";
			enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
			power-supply = <&vreg_edp_3p3>;

			pinctrl-0 = <&edp_bl_en>;
			pinctrl-names = "default";

			port {
				edp_panel_in: endpoint {
					remote-endpoint = <&mdss_dp3_out>;
				};
			};
		};
	};

	ports {
		port@1 {
			reg = <1>;
			mdss_dp3_out: endpoint {
				data-lanes = <0 1 2 3>;
				link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;

				remote-endpoint = <&edp_panel_in>;
			};
		};
	};
};

&mdss_dp3_phy {
	vdda-phy-supply = <&vreg_l3j_0p8>;
	vdda-pll-supply = <&vreg_l2j_1p2>;

	status = "okay";
};

&pcie4 {
	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;

	pinctrl-0 = <&pcie4_default>;
	pinctrl-names = "default";

	status = "okay";
};

&pcie4_phy {
	vdda-phy-supply = <&vreg_l3i_0p8>;
	vdda-pll-supply = <&vreg_l3e_1p2>;

	status = "okay";
};

&pcie5 {
	perst-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
	wake-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>;

	vddpe-3v3-supply = <&vreg_wwan>;

	pinctrl-0 = <&pcie5_default>;
	pinctrl-names = "default";

	status = "okay";
};

&pcie5_phy {
	vdda-phy-supply = <&vreg_l3i_0p8>;
	vdda-pll-supply = <&vreg_l3e_1p2>;

	status = "okay";
};

&pcie6a {
	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;

	vddpe-3v3-supply = <&vreg_nvme>;

	pinctrl-names = "default";
	pinctrl-0 = <&pcie6a_default>;

	status = "okay";
};

&pcie6a_phy {
	vdda-phy-supply = <&vreg_l1d_0p8>;
	vdda-pll-supply = <&vreg_l2j_1p2>;

	status = "okay";
};

&pmc8380_3_gpios {
	edp_bl_en: edp-bl-en-state {
		pins = "gpio4";
		function = "normal";
		power-source = <1>; /* 1.8V */
		input-disable;
		output-enable;
	};
};

&qupv3_0 {
	status = "okay";
};

&qupv3_1 {
	status = "okay";
};

&qupv3_2 {
	status = "okay";
};

&remoteproc_adsp {
	firmware-name = "qcom/x1e80100/adsp.mbn",
			"qcom/x1e80100/adsp_dtb.mbn";

	status = "okay";
};

&remoteproc_cdsp {
	firmware-name = "qcom/x1e80100/cdsp.mbn",
			"qcom/x1e80100/cdsp_dtb.mbn";

	status = "okay";
};

&smb2360_0_eusb2_repeater {
	vdd18-supply = <&vreg_l3d_1p8>;
	vdd3-supply = <&vreg_l2b_3p0>;
};

&smb2360_1_eusb2_repeater {
	vdd18-supply = <&vreg_l3d_1p8>;
	vdd3-supply = <&vreg_l14b_3p0>;
};

&smb2360_2 {
	status = "okay";
};

&smb2360_2_eusb2_repeater {
	vdd18-supply = <&vreg_l3d_1p8>;
	vdd3-supply = <&vreg_l8b_3p0>;
};

&swr0 {
	status = "okay";

	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
	pinctrl-names = "default";

	/* WSA8845, Left Woofer */
	left_woofer: speaker@0,0 {
		compatible = "sdw20217020400";
		reg = <0 0>;
		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
		#sound-dai-cells = <0>;
		sound-name-prefix = "WooferLeft";
		vdd-1p8-supply = <&vreg_l15b_1p8>;
		vdd-io-supply = <&vreg_l12b_1p2>;
		qcom,port-mapping = <1 2 3 7 10 13>;
	};

	/* WSA8845, Left Tweeter */
	left_tweeter: speaker@0,1 {
		compatible = "sdw20217020400";
		reg = <0 1>;
		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
		#sound-dai-cells = <0>;
		sound-name-prefix = "TweeterLeft";
		vdd-1p8-supply = <&vreg_l15b_1p8>;
		vdd-io-supply = <&vreg_l12b_1p2>;
		qcom,port-mapping = <4 5 6 7 11 13>;
	};
};

&swr1 {
	status = "okay";

	/* WCD9385 RX */
	wcd_rx: codec@0,4 {
		compatible = "sdw20217010d00";
		reg = <0 4>;
		qcom,rx-port-mapping = <1 2 3 4 5>;
	};
};

&swr2 {
	status = "okay";

	/* WCD9385 TX */
	wcd_tx: codec@0,3 {
		compatible = "sdw20217010d00";
		reg = <0 3>;
		qcom,tx-port-mapping = <2 2 3 4>;
	};
};

&swr3 {
	status = "okay";

	pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
	pinctrl-names = "default";

	/* WSA8845, Right Woofer */
	right_woofer: speaker@0,0 {
		compatible = "sdw20217020400";
		reg = <0 0>;
		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
		#sound-dai-cells = <0>;
		sound-name-prefix = "WooferRight";
		vdd-1p8-supply = <&vreg_l15b_1p8>;
		vdd-io-supply = <&vreg_l12b_1p2>;
		qcom,port-mapping = <1 2 3 7 10 13>;
	};

	/* WSA8845, Right Tweeter */
	right_tweeter: speaker@0,1 {
		compatible = "sdw20217020400";
		reg = <0 1>;
		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
		#sound-dai-cells = <0>;
		sound-name-prefix = "TweeterRight";
		vdd-1p8-supply = <&vreg_l15b_1p8>;
		vdd-io-supply = <&vreg_l12b_1p2>;
		qcom,port-mapping = <4 5 6 7 11 13>;
	};
};

&tlmm {
	gpio-reserved-ranges = <34 2>, /* Unused */
			       <44 4>, /* SPI (TPM) */
			       <238 1>; /* UFS Reset */

	edp_reg_en: edp-reg-en-state {
		pins = "gpio70";
		function = "gpio";
		drive-strength = <16>;
		bias-disable;
	};

	hall_int_n_default: hall-int-n-state {
		pins = "gpio92";
		function = "gpio";
		bias-disable;
	};

	kybd_default: kybd-default-state {
		pins = "gpio67";
		function = "gpio";
		bias-disable;
	};

	nvme_reg_en: nvme-reg-en-state {
		pins = "gpio18";
		function = "gpio";
		drive-strength = <2>;
		bias-disable;
	};

	pcie4_default: pcie4-default-state {
		clkreq-n-pins {
			pins = "gpio147";
			function = "pcie4_clk";
			drive-strength = <2>;
			bias-pull-up;
		};

		perst-n-pins {
			pins = "gpio146";
			function = "gpio";
			drive-strength = <2>;
			bias-disable;
		};

		wake-n-pins {
			pins = "gpio148";
			function = "gpio";
			drive-strength = <2>;
			bias-pull-up;
		};
	};

	pcie5_default: pcie5-default-state {
		clkreq-n-pins {
			pins = "gpio150";
			function = "pcie5_clk";
			drive-strength = <2>;
			bias-pull-up;
		};

		perst-n-pins {
			pins = "gpio149";
			function = "gpio";
			drive-strength = <2>;
			bias-disable;
		};

		wake-n-pins {
			pins = "gpio151";
			function = "gpio";
			drive-strength = <2>;
			bias-pull-up;
		};
	};

	pcie6a_default: pcie6a-default-state {
		clkreq-n-pins {
			pins = "gpio153";
			function = "pcie6a_clk";
			drive-strength = <2>;
			bias-pull-up;
		};

		perst-n-pins {
			pins = "gpio152";
			function = "gpio";
			drive-strength = <2>;
			bias-disable;
		};

		wake-n-pins {
			pins = "gpio154";
			function = "gpio";
			drive-strength = <2>;
			bias-pull-up;
		};
	};

	tpad_default: tpad-default-state {
		pins = "gpio3";
		function = "gpio";
		bias-disable;
	};

	ts0_default: ts0-default-state {
		int-n-pins {
			pins = "gpio51";
			function = "gpio";
			bias-disable;
		};

		reset-n-pins {
			pins = "gpio48";
			function = "gpio";
			output-high;
			drive-strength = <16>;
		};
	};

	wcd_default: wcd-reset-n-active-state {
		pins = "gpio191";
		function = "gpio";
		drive-strength = <16>;
		bias-disable;
		output-low;
	};

	wwan_sw_en: wwan-sw-en-state {
		pins = "gpio221";
		function = "gpio";
		drive-strength = <4>;
		bias-disable;
	};
};

&uart21 {
	compatible = "qcom,geni-debug-uart";
	status = "okay";
};

&usb_1_ss0_hsphy {
	vdd-supply = <&vreg_l3j_0p8>;
	vdda12-supply = <&vreg_l2j_1p2>;

	phys = <&smb2360_0_eusb2_repeater>;

	status = "okay";
};

&usb_1_ss0_qmpphy {
	vdda-phy-supply = <&vreg_l3e_1p2>;
	vdda-pll-supply = <&vreg_l1j_0p8>;

	status = "okay";
};

&usb_1_ss0 {
	status = "okay";
};

&usb_1_ss0_dwc3 {
	dr_mode = "host";
};

&usb_1_ss0_dwc3_hs {
	remote-endpoint = <&pmic_glink_ss0_hs_in>;
};

&usb_1_ss0_qmpphy_out {
	remote-endpoint = <&pmic_glink_ss0_ss_in>;
};

&usb_1_ss1_hsphy {
	vdd-supply = <&vreg_l3j_0p8>;
	vdda12-supply = <&vreg_l2j_1p2>;

	phys = <&smb2360_1_eusb2_repeater>;

	status = "okay";
};

&usb_1_ss1_qmpphy {
	vdda-phy-supply = <&vreg_l3e_1p2>;
	vdda-pll-supply = <&vreg_l2d_0p9>;

	status = "okay";
};

&usb_1_ss1 {
	status = "okay";
};

&usb_1_ss1_dwc3 {
	dr_mode = "host";
};

&usb_1_ss1_dwc3_hs {
	remote-endpoint = <&pmic_glink_ss1_hs_in>;
};

&usb_1_ss1_qmpphy_out {
	remote-endpoint = <&pmic_glink_ss1_ss_in>;
};

&usb_1_ss2_hsphy {
	vdd-supply = <&vreg_l3j_0p8>;
	vdda12-supply = <&vreg_l2j_1p2>;

	phys = <&smb2360_2_eusb2_repeater>;

	status = "okay";
};

&usb_1_ss2_qmpphy {
	vdda-phy-supply = <&vreg_l3e_1p2>;
	vdda-pll-supply = <&vreg_l2d_0p9>;

	status = "okay";
};

&usb_1_ss2 {
	status = "okay";
};

&usb_1_ss2_dwc3 {
	dr_mode = "host";
};

&usb_1_ss2_dwc3_hs {
	remote-endpoint = <&pmic_glink_ss2_hs_in>;
};

&usb_1_ss2_qmpphy_out {
	remote-endpoint = <&pmic_glink_ss2_ss_in>;
};