nvidiafb: Add boot option to reverse i2c port assignment
There are a few nvidia hardware where the i2c port assignments are reversed,
i.e., the 1st i2c port is assigned to the secondary display and the 2nd i2c
port to the primary display. In most cases, if only 1 display is attached, or
if only 1 flatpanel and 1 analog display is attached, the port reversal is of
no consequence. However if 2 flatpanels are attached, it can cause display
problems.
There is no sane way of determining if the hardware reversed the i2c port
assignment, so the simplest fix is to add a boot/module option, "reverse_i2c
to explicitly reverse the i2c port.
This also restores i2c ordering back to the pre-2.6.22 state.
Signed-off-by: Antonino Daplas <adaplas@gail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/video/nvidia/nv_i2c.c b/drivers/video/nvidia/nv_i2c.c
index afe4567..0cbcb3d 100644
--- a/drivers/video/nvidia/nv_i2c.c
+++ b/drivers/video/nvidia/nv_i2c.c
@@ -125,11 +125,11 @@
par->chan[1].par = par;
par->chan[2].par = par;
- par->chan[0].ddc_base = 0x36;
- nvidia_setup_i2c_bus(&par->chan[0], "nvidia #0", I2C_CLASS_HWMON);
+ par->chan[0].ddc_base = (par->reverse_i2c) ? 0x36 : 0x3e;
+ nvidia_setup_i2c_bus(&par->chan[0], "nvidia #0", 0);
- par->chan[1].ddc_base = 0x3e;
- nvidia_setup_i2c_bus(&par->chan[1], "nvidia #1", 0);
+ par->chan[1].ddc_base = (par->reverse_i2c) ? 0x3e : 0x36;
+ nvidia_setup_i2c_bus(&par->chan[1], "nvidia #1", I2C_CLASS_HWMON);
par->chan[2].ddc_base = 0x50;
nvidia_setup_i2c_bus(&par->chan[2], "nvidia #2", 0);
diff --git a/drivers/video/nvidia/nv_type.h b/drivers/video/nvidia/nv_type.h
index 2fdf77ec3..f132aab 100644
--- a/drivers/video/nvidia/nv_type.h
+++ b/drivers/video/nvidia/nv_type.h
@@ -135,6 +135,7 @@
int paneltweak;
int LVDS;
int pm_state;
+ int reverse_i2c;
u32 crtcSync_read;
u32 fpSyncs;
u32 dmaPut;
diff --git a/drivers/video/nvidia/nvidia.c b/drivers/video/nvidia/nvidia.c
index a7fe214..30e14eb 100644
--- a/drivers/video/nvidia/nvidia.c
+++ b/drivers/video/nvidia/nvidia.c
@@ -79,6 +79,7 @@
static int paneltweak __devinitdata = 0;
static int vram __devinitdata = 0;
static int bpp __devinitdata = 8;
+static int reverse_i2c __devinitdata;
#ifdef CONFIG_MTRR
static int nomtrr __devinitdata = 0;
#endif
@@ -1305,6 +1306,7 @@
par->CRTCnumber = forceCRTC;
par->FpScale = (!noscale);
par->paneltweak = paneltweak;
+ par->reverse_i2c = reverse_i2c;
/* enable IO and mem if not already done */
pci_read_config_word(pd, PCI_COMMAND, &cmd);
@@ -1486,6 +1488,8 @@
noaccel = 1;
} else if (!strncmp(this_opt, "noscale", 7)) {
noscale = 1;
+ } else if (!strncmp(this_opt, "reverse_i2c", 11)) {
+ reverse_i2c = 1;
} else if (!strncmp(this_opt, "paneltweak:", 11)) {
paneltweak = simple_strtoul(this_opt+11, NULL, 0);
} else if (!strncmp(this_opt, "vram:", 5)) {
@@ -1582,6 +1586,8 @@
module_param(bpp, int, 0);
MODULE_PARM_DESC(bpp, "pixel width in bits"
"(default=8)");
+module_param(reverse_i2c, int, 0);
+MODULE_PARM_DESC(reverse_i2c, "reverse port assignment of the i2c bus");
#ifdef CONFIG_MTRR
module_param(nomtrr, bool, 0);
MODULE_PARM_DESC(nomtrr, "Disables MTRR support (0 or 1=disabled) "
