// SPDX-License-Identifier: GPL-2.0-only OR MIT
/*
 * Copyright (C) 2020-2024 Texas Instruments Incorporated - https://www.ti.com/
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>

#include "k3-j7200.dtsi"

/ {
	memory@80000000 {
		device_type = "memory";
		bootph-all;
		/* 4G RAM */
		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
		      <0x00000008 0x80000000 0x00000000 0x80000000>;
	};

	reserved_memory: reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		secure_ddr: optee@9e800000 {
			reg = <0x00 0x9e800000 0x00 0x01800000>;
			alignment = <0x1000>;
			no-map;
		};

		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0xa0000000 0x00 0x100000>;
			no-map;
		};

		mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0xa0100000 0x00 0xf00000>;
			no-map;
		};

		mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0xa1000000 0x00 0x100000>;
			no-map;
		};

		mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0xa1100000 0x00 0xf00000>;
			no-map;
		};

		main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0xa2000000 0x00 0x100000>;
			no-map;
		};

		main_r5fss0_core0_memory_region: r5f-memory@a2100000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0xa2100000 0x00 0xf00000>;
			no-map;
		};

		main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0xa3000000 0x00 0x100000>;
			no-map;
		};

		main_r5fss0_core1_memory_region: r5f-memory@a3100000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0xa3100000 0x00 0xf00000>;
			no-map;
		};

		rtos_ipc_memory_region: ipc-memories@a4000000 {
			reg = <0x00 0xa4000000 0x00 0x00800000>;
			alignment = <0x1000>;
			no-map;
		};
	};

	mux0: mux-controller-0 {
		compatible = "gpio-mux";
		#mux-state-cells = <1>;
		mux-gpios = <&exp_som 1 GPIO_ACTIVE_HIGH>;
	};

	mux1: mux-controller-1 {
		compatible = "gpio-mux";
		#mux-state-cells = <1>;
		mux-gpios = <&exp_som 2 GPIO_ACTIVE_HIGH>;
	};

	transceiver0: can-phy0 {
		/* standby pin has been grounded by default */
		compatible = "ti,tcan1042";
		#phy-cells = <0>;
		max-bitrate = <5000000>;
	};
};

&wkup_pmx0 {
	mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-default-pins {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (B6) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */
			J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C8) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */
			J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (D6) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */
			J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (D7) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */
			J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (B7) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */
			J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D8) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */
			J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (C7) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */
			J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (C5) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */
			J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (A5) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */
			J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (A6) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */
			J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
			J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
			J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
		>;
	};

	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
			J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
			J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0)  /* MCU_OSPI0_D0 */
			J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0)  /* MCU_OSPI0_D1 */
			J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0)  /* MCU_OSPI0_D2 */
			J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0)  /* MCU_OSPI0_D3 */
			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0)  /* MCU_OSPI0_D4 */
			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0)  /* MCU_OSPI0_D5 */
			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0)  /* MCU_OSPI0_D6 */
			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0)  /* MCU_OSPI0_D7 */
			J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0)  /* MCU_OSPI0_DQS */
		>;
	};
};

&wkup_pmx2 {
	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
			pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
			J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
		>;
	};
};

&wkup_pmx3 {
	pmic_irq_pins_default: pmic-irq-default-pins {
		pinctrl-single,pins = <
			J721E_WKUP_IOPAD(0x01c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
		>;
	};
};

&main_pmx0 {
	main_i2c0_pins_default: main-i2c0-default-pins {
		pinctrl-single,pins = <
			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
		>;
	};

	main_mcan0_pins_default: main-mcan0-default-pins {
		pinctrl-single,pins = <
			J721E_IOPAD(0x24, PIN_INPUT, 0) /* (V20) MCAN0_RX */
			J721E_IOPAD(0x20, PIN_OUTPUT, 0) /* (V18) MCAN0_TX */
		>;
	};
};

&hbmc {
	/* OSPI and HBMC are muxed inside FSS, Bootloader will enable
	 * appropriate node based on board detection
	 */
	status = "disabled";
	pinctrl-names = "default";
	pinctrl-0 = <&mcu_fss0_hpb0_pins_default>;
	ranges = <0x00 0x00 0x05 0x00000000 0x4000000>, /* 64MB Flash on CS0 */
		 <0x01 0x00 0x05 0x04000000 0x800000>; /* 8MB RAM on CS1 */

	flash@0,0 {
		compatible = "cypress,hyperflash", "cfi-flash";
		reg = <0x00 0x00 0x4000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "hbmc.tiboot3";
				reg = <0x0 0x100000>;
			};

			partition@100000 {
				label = "hbmc.tispl";
				reg = <0x100000 0x200000>;
			};

			partition@300000 {
				label = "hbmc.u-boot";
				reg = <0x300000 0x400000>;
			};

			partition@700000 {
				label = "hbmc.env";
				reg = <0x700000 0x40000>;
			};

			partition@800000 {
				label = "hbmc.rootfs";
				reg = <0x800000 0x3800000>;
			};
		};
	};
};

&mailbox0_cluster0 {
	status = "okay";
	interrupts = <436>;

	mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
		ti,mbox-rx = <0 0 0>;
		ti,mbox-tx = <1 0 0>;
	};

	mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
		ti,mbox-rx = <2 0 0>;
		ti,mbox-tx = <3 0 0>;
	};
};

&mailbox0_cluster1 {
	status = "okay";
	interrupts = <432>;

	mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
		ti,mbox-rx = <0 0 0>;
		ti,mbox-tx = <1 0 0>;
	};

	mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
		ti,mbox-rx = <2 0 0>;
		ti,mbox-tx = <3 0 0>;
	};
};

&mcu_r5fss0_core0 {
	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
			<&mcu_r5fss0_core0_memory_region>;
};

&mcu_r5fss0_core1 {
	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>;
	memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
			<&mcu_r5fss0_core1_memory_region>;
};

&main_r5fss0 {
	ti,cluster-mode = <0>;
};

/* Timers are used by Remoteproc firmware */
&main_timer0 {
	status = "reserved";
};

&main_timer1 {
	status = "reserved";
};

&main_timer2 {
	status = "reserved";
};

&main_r5fss0_core0 {
	mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>;
	memory-region = <&main_r5fss0_core0_dma_memory_region>,
			<&main_r5fss0_core0_memory_region>;
};

&main_r5fss0_core1 {
	mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>;
	memory-region = <&main_r5fss0_core1_dma_memory_region>,
			<&main_r5fss0_core1_memory_region>;
};

&main_i2c0 {
	pinctrl-names = "default";
	pinctrl-0 = <&main_i2c0_pins_default>;
	clock-frequency = <400000>;

	exp_som: gpio@21 {
		compatible = "ti,tca6408";
		reg = <0x21>;
		gpio-controller;
		#gpio-cells = <2>;
		gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
				  "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
				  "UART/LIN_MUX_SEL", "TRC_D17/AUDIO_REFCLK_SEL",
				  "GPIO_LIN_EN", "CAN_STB";
	};
};

&wkup_i2c0 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&wkup_i2c0_pins_default>;
	clock-frequency = <400000>;

	eeprom@50 {
		compatible = "atmel,24c256";
		reg = <0x50>;
	};

	tps659414: pmic@48 {
		compatible = "ti,tps6594-q1";
		reg = <0x48>;
		system-power-controller;
		pinctrl-names = "default";
		pinctrl-0 = <&pmic_irq_pins_default>;
		interrupt-parent = <&wkup_gpio0>;
		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
		gpio-controller;
		#gpio-cells = <2>;
		ti,primary-pmic;
		buck1-supply = <&vsys_3v3>;
		buck2-supply = <&vsys_3v3>;
		buck3-supply = <&vsys_3v3>;
		buck4-supply = <&vsys_3v3>;
		buck5-supply = <&vsys_3v3>;
		ldo1-supply = <&vsys_3v3>;
		ldo2-supply = <&vsys_3v3>;
		ldo3-supply = <&vsys_3v3>;
		ldo4-supply = <&vsys_3v3>;

		regulators {
			bucka1: buck1 {
				regulator-name = "vda_mcu_1v8";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-boot-on;
				regulator-always-on;
			};

			bucka2: buck2 {
				regulator-name = "vdd_mcuio_1v8";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-boot-on;
				regulator-always-on;
			};

			bucka3: buck3 {
				regulator-name = "vdd_mcu_0v85";
				regulator-min-microvolt = <850000>;
				regulator-max-microvolt = <850000>;
				regulator-boot-on;
				regulator-always-on;
			};

			bucka4: buck4 {
				regulator-name = "vdd_ddr_1v1";
				regulator-min-microvolt = <1100000>;
				regulator-max-microvolt = <1100000>;
				regulator-boot-on;
				regulator-always-on;
			};

			bucka5: buck5 {
				regulator-name = "vdd_phyio_1v8";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-boot-on;
				regulator-always-on;
			};

			ldoa1: ldo1 {
				regulator-name = "vdd1_lpddr4_1v8";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-boot-on;
				regulator-always-on;
			};

			ldoa2: ldo2 {
				regulator-name = "vda_dll_0v8";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <800000>;
				regulator-boot-on;
				regulator-always-on;
			};

			ldoa3: ldo3 {
				regulator-name = "vdd_wk_0v8";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <800000>;
				regulator-boot-on;
				regulator-always-on;
			};

			ldoa4: ldo4 {
				regulator-name = "vda_pll_1v8";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-boot-on;
				regulator-always-on;
			};
		};
	};

	lp876441: pmic@4c {
		compatible = "ti,lp8764-q1";
		reg = <0x4c>;
		system-power-controller;
		interrupt-parent = <&wkup_gpio0>;
		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
		gpio-controller;
		#gpio-cells = <2>;
		buck1-supply = <&vsys_3v3>;
		buck2-supply = <&vsys_3v3>;
		buck3-supply = <&vsys_3v3>;
		buck4-supply = <&vsys_3v3>;

		regulators: regulators {
			buckb1: buck1 {
				regulator-name = "vdd_cpu_avs";
				regulator-min-microvolt = <600000>;
				regulator-max-microvolt = <900000>;
				regulator-always-on;
				regulator-boot-on;
				bootph-pre-ram;
			};

			buckb2: buck2 {
				regulator-name = "vdd_ram_0v85";
				regulator-min-microvolt = <850000>;
				regulator-max-microvolt = <850000>;
				regulator-boot-on;
				regulator-always-on;
			};

			buckb3: buck3 {
				regulator-name = "vdd_core_0v85";
				regulator-min-microvolt = <850000>;
				regulator-max-microvolt = <850000>;
				regulator-boot-on;
				regulator-always-on;
			};

			buckb4: buck4 {
				regulator-name = "vdd_io_1v8";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-boot-on;
				regulator-always-on;
			};
		};
	};
};

&ospi0 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0x0>;
		spi-tx-bus-width = <8>;
		spi-rx-bus-width = <8>;
		spi-max-frequency = <25000000>;
		cdns,tshsl-ns = <60>;
		cdns,tsd2d-ns = <60>;
		cdns,tchsh-ns = <60>;
		cdns,tslch-ns = <60>;
		cdns,read-delay = <4>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "ospi.tiboot3";
				reg = <0x0 0x100000>;
			};

			partition@100000 {
				label = "ospi.tispl";
				reg = <0x100000 0x200000>;
			};

			partition@300000 {
				label = "ospi.u-boot";
				reg = <0x300000 0x400000>;
			};

			partition@700000 {
				label = "ospi.env";
				reg = <0x700000 0x40000>;
			};

			partition@740000 {
				label = "ospi.env.backup";
				reg = <0x740000 0x40000>;
			};

			partition@800000 {
				label = "ospi.rootfs";
				reg = <0x800000 0x37c0000>;
			};

			partition@3fc0000 {
				label = "ospi.phypattern";
				reg = <0x3fc0000 0x40000>;
			};
		};
	};
};

&main_mcan0 {
	status = "okay";
	pinctrl-0 = <&main_mcan0_pins_default>;
	pinctrl-names = "default";
	phys = <&transceiver0>;
};