/*
 * Hardkernel Odroid XU3 board device tree source
 *
 * Copyright (c) 2014 Collabora Ltd.
 * Copyright (c) 2013 Samsung Electronics Co., Ltd.
 *		http://www.samsung.com
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
*/

#include <dt-bindings/clock/samsung,s2mps11.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/sound/samsung-i2s.h>
#include "exynos5800.dtsi"
#include "exynos5422-cpus.dtsi"
#include "exynos5422-cpu-thermal.dtsi"

/ {
	memory {
		reg = <0x40000000 0x7EA00000>;
	};

	chosen {
		linux,stdout-path = &serial_2;
	};

	firmware@02073000 {
		compatible = "samsung,secure-firmware";
		reg = <0x02073000 0x1000>;
	};

	fixed-rate-clocks {
		oscclk {
			compatible = "samsung,exynos5420-oscclk";
			clock-frequency = <24000000>;
		};
	};

	emmc_pwrseq: pwrseq {
		pinctrl-0 = <&emmc_nrst_pin>;
		pinctrl-names = "default";
		compatible = "mmc-pwrseq-emmc";
		reset-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>;
	};

	fan0: pwm-fan {
		compatible = "pwm-fan";
		pwms = <&pwm 0 20972 0>;
		cooling-min-state = <0>;
		cooling-max-state = <3>;
		#cooling-cells = <2>;
		cooling-levels = <0 130 170 230>;
	};
};

&clock_audss {
	assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>,
			<&clock_audss EXYNOS_MOUT_I2S>,
			<&clock_audss EXYNOS_DOUT_AUD_BUS>;
	assigned-clock-parents = <&clock CLK_FIN_PLL>,
			<&clock_audss EXYNOS_MOUT_AUDSS>;
	assigned-clock-rates = <0>,
			<0>,
			<19200000>;
};

&hdmi {
	status = "okay";
	hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
	pinctrl-names = "default";
	pinctrl-0 = <&hdmi_hpd_irq>;

	vdd_osc-supply = <&ldo7_reg>;
	vdd_pll-supply = <&ldo6_reg>;
	vdd-supply = <&ldo6_reg>;
};

&hsi2c_4 {
	status = "okay";

	s2mps11_pmic@66 {
		compatible = "samsung,s2mps11-pmic";
		reg = <0x66>;
		s2mps11,buck2-ramp-delay = <12>;
		s2mps11,buck34-ramp-delay = <12>;
		s2mps11,buck16-ramp-delay = <12>;
		s2mps11,buck6-ramp-enable = <1>;
		s2mps11,buck2-ramp-enable = <1>;
		s2mps11,buck3-ramp-enable = <1>;
		s2mps11,buck4-ramp-enable = <1>;
		samsung,s2mps11-acokb-ground;

		interrupt-parent = <&gpx0>;
		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
		pinctrl-names = "default";
		pinctrl-0 = <&s2mps11_irq>;

		s2mps11_osc: clocks {
			#clock-cells = <1>;
			clock-output-names = "s2mps11_ap",
					"s2mps11_cp", "s2mps11_bt";
		};

		regulators {
			ldo1_reg: LDO1 {
				regulator-name = "vdd_ldo1";
				regulator-min-microvolt = <1000000>;
				regulator-max-microvolt = <1000000>;
				regulator-always-on;
			};

			ldo3_reg: LDO3 {
				regulator-name = "vdd_ldo3";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-always-on;
			};

			ldo5_reg: LDO5 {
				regulator-name = "vdd_ldo5";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-always-on;
			};

			ldo6_reg: LDO6 {
				regulator-name = "vdd_ldo6";
				regulator-min-microvolt = <1000000>;
				regulator-max-microvolt = <1000000>;
				regulator-always-on;
			};

			ldo7_reg: LDO7 {
				regulator-name = "vdd_ldo7";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-always-on;
			};

			ldo8_reg: LDO8 {
				regulator-name = "vdd_ldo8";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-always-on;
			};

			ldo9_reg: LDO9 {
				regulator-name = "vdd_ldo9";
				regulator-min-microvolt = <3000000>;
				regulator-max-microvolt = <3000000>;
				regulator-always-on;
			};

			ldo10_reg: LDO10 {
				regulator-name = "vdd_ldo10";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-always-on;
			};

			ldo11_reg: LDO11 {
				regulator-name = "vdd_ldo11";
				regulator-min-microvolt = <1000000>;
				regulator-max-microvolt = <1000000>;
				regulator-always-on;
			};

			ldo12_reg: LDO12 {
				regulator-name = "vdd_ldo12";
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-always-on;
			};

			ldo13_reg: LDO13 {
				regulator-name = "vdd_ldo13";
				regulator-min-microvolt = <2800000>;
				regulator-max-microvolt = <2800000>;
				regulator-always-on;
			};

			ldo15_reg: LDO15 {
				regulator-name = "vdd_ldo15";
				regulator-min-microvolt = <3100000>;
				regulator-max-microvolt = <3100000>;
				regulator-always-on;
			};

			ldo16_reg: LDO16 {
				regulator-name = "vdd_ldo16";
				regulator-min-microvolt = <2200000>;
				regulator-max-microvolt = <2200000>;
				regulator-always-on;
			};

			ldo17_reg: LDO17 {
				regulator-name = "tsp_avdd";
				regulator-min-microvolt = <3300000>;
				regulator-max-microvolt = <3300000>;
				regulator-always-on;
			};

			ldo19_reg: LDO19 {
				regulator-name = "vdd_sd";
				regulator-min-microvolt = <2800000>;
				regulator-max-microvolt = <2800000>;
				regulator-always-on;
			};

			ldo24_reg: LDO24 {
				regulator-name = "tsp_io";
				regulator-min-microvolt = <2800000>;
				regulator-max-microvolt = <2800000>;
				regulator-always-on;
			};

			ldo26_reg: LDO26 {
				regulator-name = "vdd_ldo26";
				regulator-min-microvolt = <3000000>;
				regulator-max-microvolt = <3000000>;
				regulator-always-on;
			};

			buck1_reg: BUCK1 {
				regulator-name = "vdd_mif";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <1300000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck2_reg: BUCK2 {
				regulator-name = "vdd_arm";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <1500000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck3_reg: BUCK3 {
				regulator-name = "vdd_int";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <1400000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck4_reg: BUCK4 {
				regulator-name = "vdd_g3d";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <1400000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck5_reg: BUCK5 {
				regulator-name = "vdd_mem";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <1400000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck6_reg: BUCK6 {
				regulator-name = "vdd_kfc";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <1500000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck7_reg: BUCK7 {
				regulator-name = "vdd_1.0v_ldo";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <1500000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck8_reg: BUCK8 {
				regulator-name = "vdd_1.8v_ldo";
				regulator-min-microvolt = <800000>;
				regulator-max-microvolt = <1500000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck9_reg: BUCK9 {
				regulator-name = "vdd_2.8v_ldo";
				regulator-min-microvolt = <3000000>;
				regulator-max-microvolt = <3750000>;
				regulator-always-on;
				regulator-boot-on;
			};

			buck10_reg: BUCK10 {
				regulator-name = "vdd_vmem";
				regulator-min-microvolt = <2850000>;
				regulator-max-microvolt = <2850000>;
				regulator-always-on;
				regulator-boot-on;
			};
		};
	};
};

&i2c_2 {
	samsung,i2c-sda-delay = <100>;
	samsung,i2c-max-bus-freq = <66000>;
	status = "okay";

	hdmiddc@50 {
		compatible = "samsung,exynos4210-hdmiddc";
		reg = <0x50>;
	};
};

&mfc {
	samsung,mfc-r = <0x43000000 0x800000>;
	samsung,mfc-l = <0x51000000 0x800000>;
};

&mmc_0 {
	status = "okay";
	mmc-pwrseq = <&emmc_pwrseq>;
	cd-gpios = <&gpc0 2 GPIO_ACTIVE_LOW>;
	card-detect-delay = <200>;
	samsung,dw-mshc-ciu-div = <3>;
	samsung,dw-mshc-sdr-timing = <0 4>;
	samsung,dw-mshc-ddr-timing = <0 2>;
	samsung,dw-mshc-hs400-timing = <0 2>;
	samsung,read-strobe-delay = <90>;
	pinctrl-names = "default";
	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>;
	bus-width = <8>;
	cap-mmc-highspeed;
	mmc-hs200-1_8v;
	mmc-hs400-1_8v;
};

&mmc_2 {
	status = "okay";
	card-detect-delay = <200>;
	samsung,dw-mshc-ciu-div = <3>;
	samsung,dw-mshc-sdr-timing = <0 4>;
	samsung,dw-mshc-ddr-timing = <0 2>;
	pinctrl-names = "default";
	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
	bus-width = <4>;
	cap-sd-highspeed;
};

&pinctrl_0 {
	hdmi_hpd_irq: hdmi-hpd-irq {
		samsung,pins = "gpx3-7";
		samsung,pin-function = <0>;
		samsung,pin-pud = <1>;
		samsung,pin-drv = <0>;
	};

	s2mps11_irq: s2mps11-irq {
		samsung,pins = "gpx0-4";
		samsung,pin-function = <0xf>;
		samsung,pin-pud = <0>;
		samsung,pin-drv = <0>;
	};
};

&pinctrl_1 {
	emmc_nrst_pin: emmc-nrst {
		samsung,pins = "gpd1-0";
		samsung,pin-function = <0>;
		samsung,pin-pud = <0>;
		samsung,pin-drv = <0>;
	};
};

&tmu_cpu0 {
	vtmu-supply = <&ldo7_reg>;
	status = "okay";
};

&tmu_cpu1 {
	vtmu-supply = <&ldo7_reg>;
	status = "okay";
};

&tmu_cpu2 {
	vtmu-supply = <&ldo7_reg>;
	status = "okay";
};

&tmu_cpu3 {
	vtmu-supply = <&ldo7_reg>;
	status = "okay";
};

&tmu_gpu {
	vtmu-supply = <&ldo7_reg>;
	status = "okay";
};

&rtc {
	status = "okay";
	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
	clock-names = "rtc", "rtc_src";
};

&usbdrd_dwc3_0 {
	dr_mode = "host";
};

/* usbdrd_dwc3_1 mode customized in each board */

&usbdrd3_0 {
	vdd33-supply = <&ldo9_reg>;
	vdd10-supply = <&ldo11_reg>;
};

&usbdrd3_1 {
	vdd33-supply = <&ldo9_reg>;
	vdd10-supply = <&ldo11_reg>;
};