diff --git a/drivers/cxl/cxl.h b/drivers/cxl/cxl.h
index 8fd4a17..6f14838 100644
--- a/drivers/cxl/cxl.h
+++ b/drivers/cxl/cxl.h
@@ -69,6 +69,7 @@ struct cxl_memdev;
  *                (CXL 2.0 8.2.8.4.3 Mailbox Capabilities Register)
  * @mbox_mutex: Mutex to synchronize mailbox access.
  * @firmware_version: Firmware version for the memory device.
+ * @enabled_commands: Hardware commands found enabled in CEL.
  * @pmem_range: Persistent memory capacity information.
  * @ram_range: Volatile memory capacity information.
  */
@@ -84,6 +85,7 @@ struct cxl_mem {
 	size_t payload_size;
 	struct mutex mbox_mutex; /* Protects device mailbox and firmware */
 	char firmware_version[0x10];
+	unsigned long *enabled_cmds;
 
 	struct range pmem_range;
 	struct range ram_range;
diff --git a/drivers/cxl/mem.c b/drivers/cxl/mem.c
index 5319412..e31b304 100644
--- a/drivers/cxl/mem.c
+++ b/drivers/cxl/mem.c
@@ -46,6 +46,8 @@ enum opcode {
 	CXL_MBOX_OP_INVALID		= 0x0000,
 	CXL_MBOX_OP_RAW			= CXL_MBOX_OP_INVALID,
 	CXL_MBOX_OP_ACTIVATE_FW		= 0x0202,
+	CXL_MBOX_OP_GET_SUPPORTED_LOGS	= 0x0400,
+	CXL_MBOX_OP_GET_LOG		= 0x0401,
 	CXL_MBOX_OP_IDENTIFY		= 0x4000,
 	CXL_MBOX_OP_SET_PARTITION_INFO	= 0x4101,
 	CXL_MBOX_OP_SET_LSA		= 0x4103,
@@ -108,10 +110,28 @@ static DEFINE_IDA(cxl_memdev_ida);
 static struct dentry *cxl_debugfs;
 static bool cxl_raw_allow_all;
 
+enum {
+	CEL_UUID,
+	VENDOR_DEBUG_UUID,
+};
+
+/* See CXL 2.0 Table 170. Get Log Input Payload */
+static const uuid_t log_uuid[] = {
+	[CEL_UUID] = UUID_INIT(0xda9c0b5, 0xbf41, 0x4b78, 0x8f, 0x79, 0x96,
+			       0xb1, 0x62, 0x3b, 0x3f, 0x17),
+	[VENDOR_DEBUG_UUID] = UUID_INIT(0xe1819d9, 0x11a9, 0x400c, 0x81, 0x1f,
+					0xd6, 0x07, 0x19, 0x40, 0x3d, 0x86),
+};
+
 /**
  * struct cxl_mem_command - Driver representation of a memory device command
  * @info: Command information as it exists for the UAPI
  * @opcode: The actual bits used for the mailbox protocol
+ * @flags: Set of flags effecting driver behavior.
+ *
+ *  * %CXL_CMD_FLAG_FORCE_ENABLE: In cases of error, commands with this flag
+ *    will be enabled by the driver regardless of what hardware may have
+ *    advertised.
  *
  * The cxl_mem_command is the driver's internal representation of commands that
  * are supported by the driver. Some of these commands may not be supported by
@@ -123,9 +143,12 @@ static bool cxl_raw_allow_all;
 struct cxl_mem_command {
 	struct cxl_command_info info;
 	enum opcode opcode;
+	u32 flags;
+#define CXL_CMD_FLAG_NONE 0
+#define CXL_CMD_FLAG_FORCE_ENABLE BIT(0)
 };
 
-#define CXL_CMD(_id, sin, sout)                                                \
+#define CXL_CMD(_id, sin, sout, _flags)                                        \
 	[CXL_MEM_COMMAND_ID_##_id] = {                                         \
 	.info =	{                                                              \
 			.id = CXL_MEM_COMMAND_ID_##_id,                        \
@@ -133,6 +156,7 @@ struct cxl_mem_command {
 			.size_out = sout,                                      \
 		},                                                             \
 	.opcode = CXL_MBOX_OP_##_id,                                           \
+	.flags = _flags,                                                       \
 	}
 
 /*
@@ -142,10 +166,11 @@ struct cxl_mem_command {
  * 0, and the user passed in 1, it is an error.
  */
 static struct cxl_mem_command mem_commands[] = {
-	CXL_CMD(IDENTIFY, 0, 0x43),
+	CXL_CMD(IDENTIFY, 0, 0x43, CXL_CMD_FLAG_FORCE_ENABLE),
 #ifdef CONFIG_CXL_MEM_RAW_COMMANDS
-	CXL_CMD(RAW, ~0, ~0),
+	CXL_CMD(RAW, ~0, ~0, 0),
 #endif
+	CXL_CMD(GET_SUPPORTED_LOGS, 0, ~0, CXL_CMD_FLAG_FORCE_ENABLE),
 };
 
 /*
@@ -633,6 +658,10 @@ static int cxl_validate_cmd_from_user(struct cxl_mem *cxlm,
 	c = &mem_commands[send_cmd->id];
 	info = &c->info;
 
+	/* Check that the command is enabled for hardware */
+	if (!test_bit(info->id, cxlm->enabled_cmds))
+		return -ENOTTY;
+
 	/* Check the input buffer is the expected size */
 	if (info->size_in >= 0 && info->size_in != send_cmd->in.size)
 		return -ENOMEM;
@@ -757,6 +786,17 @@ static const struct file_operations cxl_memdev_fops = {
 	.llseek = noop_llseek,
 };
 
+static inline struct cxl_mem_command *cxl_mem_find_command(u16 opcode)
+{
+	struct cxl_mem_command *c;
+
+	cxl_for_each_cmd(c)
+		if (c->opcode == opcode)
+			return c;
+
+	return NULL;
+}
+
 /**
  * cxl_mem_mbox_send_cmd() - Send a mailbox command to a memory device.
  * @cxlm: The CXL memory device to communicate with.
@@ -777,9 +817,7 @@ static const struct file_operations cxl_memdev_fops = {
  *
  * Mailbox commands may execute successfully yet the device itself reported an
  * error. While this distinction can be useful for commands from userspace, the
- * kernel will only be able to use results when both are successful. It's
- * expected that all callers of this function know exactly the size of the data
- * they will consume from the hardware.
+ * kernel will only be able to use results when both are successful.
  *
  * See __cxl_mem_mbox_send_cmd()
  */
@@ -787,6 +825,7 @@ static int cxl_mem_mbox_send_cmd(struct cxl_mem *cxlm, u16 opcode,
 				 void *in, size_t in_size,
 				 void *out, size_t out_size)
 {
+	const struct cxl_mem_command *cmd = cxl_mem_find_command(opcode);
 	struct mbox_cmd mbox_cmd = {
 		.opcode = opcode,
 		.payload_in = in,
@@ -812,7 +851,11 @@ static int cxl_mem_mbox_send_cmd(struct cxl_mem *cxlm, u16 opcode,
 	if (mbox_cmd.return_code != CXL_MBOX_SUCCESS)
 		return -ENXIO;
 
-	if (mbox_cmd.size_out != out_size)
+	/*
+	 * Variable sized commands can't be validated and so it's up to the
+	 * caller to do that if they wish.
+	 */
+	if (cmd->info.size_out >= 0 && mbox_cmd.size_out != out_size)
 		return -EIO;
 
 	return 0;
@@ -947,6 +990,14 @@ static struct cxl_mem *cxl_mem_create(struct pci_dev *pdev, u32 reg_lo,
 	mutex_init(&cxlm->mbox_mutex);
 	cxlm->pdev = pdev;
 	cxlm->regs = regs + offset;
+	cxlm->enabled_cmds =
+		devm_kmalloc_array(dev, BITS_TO_LONGS(cxl_cmd_count),
+				   sizeof(unsigned long),
+				   GFP_KERNEL | __GFP_ZERO);
+	if (!cxlm->enabled_cmds) {
+		dev_err(dev, "No memory available for bitmap\n");
+		return NULL;
+	}
 
 	dev_dbg(dev, "Mapped CXL Memory Device resource\n");
 	return cxlm;
@@ -1166,6 +1217,160 @@ static int cxl_mem_add_memdev(struct cxl_mem *cxlm)
 	return rc;
 }
 
+static int cxl_xfer_log(struct cxl_mem *cxlm, uuid_t *uuid, u32 size, u8 *out)
+{
+	u32 remaining = size;
+	u32 offset = 0;
+
+	while (remaining) {
+		u32 xfer_size = min_t(u32, remaining, cxlm->payload_size);
+		struct cxl_mbox_get_log {
+			uuid_t uuid;
+			__le32 offset;
+			__le32 length;
+		} __packed log = {
+			.uuid = *uuid,
+			.offset = cpu_to_le32(offset),
+			.length = cpu_to_le32(xfer_size)
+		};
+		int rc;
+
+		rc = cxl_mem_mbox_send_cmd(cxlm, CXL_MBOX_OP_GET_LOG, &log,
+					   sizeof(log), out, xfer_size);
+		if (rc < 0)
+			return rc;
+
+		out += xfer_size;
+		remaining -= xfer_size;
+		offset += xfer_size;
+	}
+
+	return 0;
+}
+
+/**
+ * cxl_walk_cel() - Walk through the Command Effects Log.
+ * @cxlm: Device.
+ * @size: Length of the Command Effects Log.
+ * @cel: CEL
+ *
+ * Iterate over each entry in the CEL and determine if the driver supports the
+ * command. If so, the command is enabled for the device and can be used later.
+ */
+static void cxl_walk_cel(struct cxl_mem *cxlm, size_t size, u8 *cel)
+{
+	struct cel_entry {
+		__le16 opcode;
+		__le16 effect;
+	} __packed * cel_entry;
+	const int cel_entries = size / sizeof(*cel_entry);
+	int i;
+
+	cel_entry = (struct cel_entry *)cel;
+
+	for (i = 0; i < cel_entries; i++) {
+		u16 opcode = le16_to_cpu(cel_entry[i].opcode);
+		struct cxl_mem_command *cmd = cxl_mem_find_command(opcode);
+
+		if (!cmd) {
+			dev_dbg(&cxlm->pdev->dev,
+				"Opcode 0x%04x unsupported by driver", opcode);
+			continue;
+		}
+
+		set_bit(cmd->info.id, cxlm->enabled_cmds);
+	}
+}
+
+struct cxl_mbox_get_supported_logs {
+	__le16 entries;
+	u8 rsvd[6];
+	struct gsl_entry {
+		uuid_t uuid;
+		__le32 size;
+	} __packed entry[];
+} __packed;
+
+static struct cxl_mbox_get_supported_logs *cxl_get_gsl(struct cxl_mem *cxlm)
+{
+	struct cxl_mbox_get_supported_logs *ret;
+	int rc;
+
+	ret = kvmalloc(cxlm->payload_size, GFP_KERNEL);
+	if (!ret)
+		return ERR_PTR(-ENOMEM);
+
+	rc = cxl_mem_mbox_send_cmd(cxlm, CXL_MBOX_OP_GET_SUPPORTED_LOGS, NULL,
+				   0, ret, cxlm->payload_size);
+	if (rc < 0) {
+		kvfree(ret);
+		return ERR_PTR(rc);
+	}
+
+	return ret;
+}
+
+/**
+ * cxl_mem_enumerate_cmds() - Enumerate commands for a device.
+ * @cxlm: The device.
+ *
+ * Returns 0 if enumerate completed successfully.
+ *
+ * CXL devices have optional support for certain commands. This function will
+ * determine the set of supported commands for the hardware and update the
+ * enabled_cmds bitmap in the @cxlm.
+ */
+static int cxl_mem_enumerate_cmds(struct cxl_mem *cxlm)
+{
+	struct cxl_mbox_get_supported_logs *gsl;
+	struct device *dev = &cxlm->pdev->dev;
+	struct cxl_mem_command *cmd;
+	int i, rc;
+
+	gsl = cxl_get_gsl(cxlm);
+	if (IS_ERR(gsl))
+		return PTR_ERR(gsl);
+
+	rc = -ENOENT;
+	for (i = 0; i < le16_to_cpu(gsl->entries); i++) {
+		u32 size = le32_to_cpu(gsl->entry[i].size);
+		uuid_t uuid = gsl->entry[i].uuid;
+		u8 *log;
+
+		dev_dbg(dev, "Found LOG type %pU of size %d", &uuid, size);
+
+		if (!uuid_equal(&uuid, &log_uuid[CEL_UUID]))
+			continue;
+
+		log = kvmalloc(size, GFP_KERNEL);
+		if (!log) {
+			rc = -ENOMEM;
+			goto out;
+		}
+
+		rc = cxl_xfer_log(cxlm, &uuid, size, log);
+		if (rc) {
+			kvfree(log);
+			goto out;
+		}
+
+		cxl_walk_cel(cxlm, size, log);
+		kvfree(log);
+
+		/* In case CEL was bogus, enable some default commands. */
+		cxl_for_each_cmd(cmd)
+			if (cmd->flags & CXL_CMD_FLAG_FORCE_ENABLE)
+				set_bit(cmd->info.id, cxlm->enabled_cmds);
+
+		/* Found the required CEL */
+		rc = 0;
+	}
+
+out:
+	kvfree(gsl);
+	return rc;
+}
+
 /**
  * cxl_mem_identify() - Send the IDENTIFY command to the device.
  * @cxlm: The device to identify.
@@ -1266,6 +1471,10 @@ static int cxl_mem_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	if (rc)
 		return rc;
 
+	rc = cxl_mem_enumerate_cmds(cxlm);
+	if (rc)
+		return rc;
+
 	rc = cxl_mem_identify(cxlm);
 	if (rc)
 		return rc;
diff --git a/include/uapi/linux/cxl_mem.h b/include/uapi/linux/cxl_mem.h
index c316028..59227f8 100644
--- a/include/uapi/linux/cxl_mem.h
+++ b/include/uapi/linux/cxl_mem.h
@@ -23,6 +23,7 @@
 	___C(INVALID, "Invalid Command"),                                 \
 	___C(IDENTIFY, "Identify Command"),                               \
 	___C(RAW, "Raw device command"),                                  \
+	___C(GET_SUPPORTED_LOGS, "Get Supported Logs"),                   \
 	___C(MAX, "invalid / last command")
 
 #define ___C(a, b) CXL_MEM_COMMAND_ID_##a