Merge tag 'phy-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.12
- Updates:
- Conversion to YAML binding for:
- mtk-xsphy
- mtk-tphy
- mtk-ufs
- HDMI PHY
- MIPI DSI PHY
- brcmstb-usb-phy
- Support for BCM4908 usb phy
- Support for Qualcomm SDX55 USB and QMP phy
- Support for Qualcomm SM8350 aka Snapdragon 888 UFS and USB phy
- Support for Qualcomm SDM660 USB and UFS phy
- Support for Qualcomm SC8180X USB and UFS phy
- Support for Qualcomm IPQ6018 USB phy
- Stm32 phy updates
* tag 'phy-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (41 commits)
phy: cpcap-usb: Simplify bool conversion
phy: qcom-qmp: make a const array static, makes object smaller
phy: zynqmp: Simplify code by using dev_err_probe()
phy: qcom-qmp: Add support for SM8350 UFS phy
phy: qcom-qmp: Add UFS V5 registers found in SM8350
dt-bindings: phy: qcom,qmp: Add SM8350 UFS PHY bindings
phy: qualcomm: usb28nm: Add MDM9607 init sequence
dt-bindings: phy: qcom,qusb2: document ipq6018 compatible
phy: qcom-qusb2: add QUSB2 support for IPQ6018
phy: qcom-qmp: Add SC8180X USB phy
phy: qcom-qmp: Add SC8180X UFS phy
dt-bindings: phy: qcom,qmp: Add SC8180X USB phy
dt-bindings: phy: qcom,qmp: Add SC8180X UFS to the QMP binding
dt-bindings: phy: qcom-qusb2: Document SDM660 compatible
phy: qcom-qusb2: Add configuration for SDM660
phy: qcom-qusb2: Allow specifying default clock scheme
dt-bindings: phy: qcom,usb-snps-femto-v2: Add SM8250 and SM8350 bindings
phy: qcom-qmp: Add SM8350 USB QMP PHYs
dt-bindings: phy: qcom,qmp: Add SM8150, SM8250 and SM8350 USB PHY bindings
phy: qcom-qmp: Add support for SDX55 QMP PHY
...
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
index f06f24d..8238a86 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
@@ -22,23 +22,7 @@
MIPI TX Configuration Module
============================
-The MIPI TX configuration module controls the MIPI D-PHY.
-
-Required properties:
-- compatible: "mediatek,<chip>-mipi-tx"
-- the supported chips are mt2701, 7623, mt8173 and mt8183.
-- reg: Physical base address and length of the controller's registers
-- clocks: PLL reference clock
-- clock-output-names: name of the output clock line to the DSI encoder
-- #clock-cells: must be <0>;
-- #phy-cells: must be <0>.
-
-Optional properties:
-- drive-strength-microamp: adjust driving current, should be 3000 ~ 6000. And
- the step is 200.
-- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If
- unspecified default values shall be used.
-- nvmem-cell-names: Should be "calibration-data"
+See phy/mediatek,dsi-phy.yaml
Example:
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt
index 6b1c586..b284ca5 100644
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt
@@ -53,23 +53,7 @@
HDMI PHY
========
-
-The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
-output and drives the HDMI pads.
-
-Required properties:
-- compatible: "mediatek,<chip>-hdmi-phy"
-- the supported chips are mt2701, mt7623 and mt8173
-- reg: Physical base address and length of the module's registers
-- clocks: PLL reference clock
-- clock-names: must contain "pll_ref"
-- clock-output-names: must be "hdmitx_dig_cts" on mt8173
-- #phy-cells: must be <0>
-- #clock-cells: must be <0>
-
-Optional properties:
-- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa
-- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c
+See phy/mediatek,hdmi-phy.yaml
Example:
diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
deleted file mode 100644
index 698aacb..0000000
--- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
+++ /dev/null
@@ -1,86 +0,0 @@
-Broadcom STB USB PHY
-
-Required properties:
-- compatible: should be one of
- "brcm,brcmstb-usb-phy"
- "brcm,bcm7216-usb-phy"
- "brcm,bcm7211-usb-phy"
-
-- reg and reg-names properties requirements are specific to the
- compatible string.
- "brcm,brcmstb-usb-phy":
- - reg: 1 or 2 offset and length pairs. One for the base CTRL registers
- and an optional pair for systems with USB 3.x support
- - reg-names: not specified
- "brcm,bcm7216-usb-phy":
- - reg: 3 offset and length pairs for CTRL, XHCI_EC and XHCI_GBL
- registers
- - reg-names: "ctrl", "xhci_ec", "xhci_gbl"
- "brcm,bcm7211-usb-phy":
- - reg: 5 offset and length pairs for CTRL, XHCI_EC, XHCI_GBL,
- USB_PHY and USB_MDIO registers and an optional pair
- for the BDC registers
- - reg-names: "ctrl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio", "bdc_ec"
-
-- #phy-cells: Shall be 1 as it expects one argument for setting
- the type of the PHY. Possible values are:
- - PHY_TYPE_USB2 for USB1.1/2.0 PHY
- - PHY_TYPE_USB3 for USB3.x PHY
-
-Optional Properties:
-- clocks : clock phandles.
-- clock-names: String, clock name.
-- interrupts: wakeup interrupt
-- interrupt-names: "wakeup"
-- brcm,ipp: Boolean, Invert Port Power.
- Possible values are: 0 (Don't invert), 1 (Invert)
-- brcm,ioc: Boolean, Invert Over Current detection.
- Possible values are: 0 (Don't invert), 1 (Invert)
-- dr_mode: String, PHY Device mode.
- Possible values are: "host", "peripheral ", "drd" or "typec-pd"
- If this property is not defined, the phy will default to "host" mode.
-- brcm,syscon-piarbctl: phandle to syscon for handling config registers
-NOTE: one or both of the following two properties must be set
-- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
-- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
-
-
-Example:
-
-usbphy_0: usb-phy@f0470200 {
- reg = <0xf0470200 0xb8>,
- <0xf0471940 0x6c0>;
- compatible = "brcm,brcmstb-usb-phy";
- #phy-cells = <1>;
- dr_mode = "host"
- brcm,ioc = <1>;
- brcm,ipp = <1>;
- brcm,has-xhci;
- brcm,has-eohci;
- clocks = <&usb20>, <&usb30>;
- clock-names = "sw_usb", "sw_usb3";
-};
-
-usb-phy@29f0200 {
- reg = <0x29f0200 0x200>,
- <0x29c0880 0x30>,
- <0x29cc100 0x534>,
- <0x2808000 0x24>,
- <0x2980080 0x8>;
- reg-names = "ctrl",
- "xhci_ec",
- "xhci_gbl",
- "usb_phy",
- "usb_mdio";
- brcm,ioc = <0x0>;
- brcm,ipp = <0x0>;
- compatible = "brcm,bcm7211-usb-phy";
- interrupts = <0x30>;
- interrupt-parent = <&vpu_intr1_nosec_intc>;
- interrupt-names = "wake";
- #phy-cells = <0x1>;
- brcm,has-xhci;
- syscon-piarbctl = <&syscon_piarbctl>;
- clocks = <&scmi_clk 256>;
- clock-names = "sw_usb";
-};
diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.yaml b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.yaml
new file mode 100644
index 0000000..0497368
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.yaml
@@ -0,0 +1,196 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/brcm,brcmstb-usb-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom STB USB PHY
+
+description: Broadcom's PHY that handles EHCI/OHCI and/or XHCI
+
+maintainers:
+ - Al Cooper <alcooperx@gmail.com>
+ - Rafał Miłecki <rafal@milecki.pl>
+
+properties:
+ compatible:
+ enum:
+ - brcm,bcm4908-usb-phy
+ - brcm,bcm7211-usb-phy
+ - brcm,bcm7216-usb-phy
+ - brcm,brcmstb-usb-phy
+
+ reg:
+ minItems: 1
+ maxItems: 6
+ items:
+ - description: the base CTRL register
+ - description: XHCI EC register
+ - description: XHCI GBL register
+ - description: USB PHY register
+ - description: USB MDIO register
+ - description: BDC register
+
+ reg-names:
+ minItems: 1
+ maxItems: 6
+ items:
+ - const: ctrl
+ - const: xhci_ec
+ - const: xhci_gbl
+ - const: usb_phy
+ - const: usb_mdio
+ - const: bdc_ec
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ minItems: 1
+ maxItems: 2
+ items:
+ - const: sw_usb
+ - const: sw_usb3
+
+ interrupts:
+ description: wakeup interrupt
+
+ interrupt-names:
+ const: wake
+
+ brcm,ipp:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Invert Port Power
+ minimum: 0
+ maximum: 1
+
+ brcm,ioc:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Invert Over Current detection
+ minimum: 0
+ maximum: 1
+
+ dr_mode:
+ description: PHY Device mode. If this property is not defined, the PHY will
+ default to "host" mode.
+ enum:
+ - host
+ - peripheral
+ - drd
+ - typec-pd
+
+ brcm,syscon-piarbctl:
+ description: phandle to syscon for handling config registers
+ $ref: /schemas/types.yaml#/definitions/phandle
+
+ brcm,has-xhci:
+ description: Indicates the PHY has an XHCI PHY.
+ type: boolean
+
+ brcm,has-eohci:
+ description: Indicates the PHY has an EHCI/OHCI PHY.
+ type: boolean
+
+ "#phy-cells":
+ description: |
+ Cell allows setting the type of the PHY. Possible values are:
+ - PHY_TYPE_USB2 for USB1.1/2.0 PHY
+ - PHY_TYPE_USB3 for USB3.x PHY
+ const: 1
+
+required:
+ - reg
+ - "#phy-cells"
+
+anyOf:
+ - required:
+ - brcm,has-xhci
+ - required:
+ - brcm,has-eohci
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - const: brcm,bcm4908-usb-phy
+ - const: brcm,brcmstb-usb-phy
+ then:
+ properties:
+ reg:
+ minItems: 1
+ maxItems: 2
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: brcm,bcm7211-usb-phy
+ then:
+ properties:
+ reg:
+ minItems: 5
+ maxItems: 6
+ reg-names:
+ minItems: 5
+ maxItems: 6
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: brcm,bcm7216-usb-phy
+ then:
+ properties:
+ reg:
+ minItems: 3
+ maxItems: 3
+ reg-names:
+ minItems: 3
+ maxItems: 3
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/phy/phy.h>
+
+ usb-phy@f0470200 {
+ compatible = "brcm,brcmstb-usb-phy";
+ reg = <0xf0470200 0xb8>,
+ <0xf0471940 0x6c0>;
+ #phy-cells = <1>;
+ dr_mode = "host";
+ brcm,ioc = <1>;
+ brcm,ipp = <1>;
+ brcm,has-xhci;
+ brcm,has-eohci;
+ clocks = <&usb20>, <&usb30>;
+ clock-names = "sw_usb", "sw_usb3";
+ };
+ - |
+ #include <dt-bindings/phy/phy.h>
+
+ usb-phy@29f0200 {
+ compatible = "brcm,bcm7211-usb-phy";
+ reg = <0x29f0200 0x200>,
+ <0x29c0880 0x30>,
+ <0x29cc100 0x534>,
+ <0x2808000 0x24>,
+ <0x2980080 0x8>;
+ reg-names = "ctrl",
+ "xhci_ec",
+ "xhci_gbl",
+ "usb_phy",
+ "usb_mdio";
+ brcm,ioc = <0x0>;
+ brcm,ipp = <0x0>;
+ interrupts = <0x30>;
+ interrupt-parent = <&vpu_intr1_nosec_intc>;
+ interrupt-names = "wake";
+ #phy-cells = <0x1>;
+ brcm,has-xhci;
+ brcm,syscon-piarbctl = <&syscon_piarbctl>;
+ clocks = <&scmi_clk 256>;
+ clock-names = "sw_usb";
+ };
diff --git a/Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml
new file mode 100644
index 0000000..71d4acea
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/mediatek,dsi-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek MIPI Display Serial Interface (DSI) PHY binding
+
+maintainers:
+ - Chun-Kuang Hu <chunkuang.hu@kernel.org>
+ - Philipp Zabel <p.zabel@pengutronix.de>
+ - Chunfeng Yun <chunfeng.yun@mediatek.com>
+
+description: The MIPI DSI PHY supports up to 4-lane output.
+
+properties:
+ $nodename:
+ pattern: "^dsi-phy@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - mediatek,mt2701-mipi-tx
+ - mediatek,mt7623-mipi-tx
+ - mediatek,mt8173-mipi-tx
+ - mediatek,mt8183-mipi-tx
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: PLL reference clock
+
+ clock-output-names:
+ maxItems: 1
+
+ "#phy-cells":
+ const: 0
+
+ "#clock-cells":
+ const: 0
+
+ nvmem-cells:
+ maxItems: 1
+ description: A phandle to the calibration data provided by a nvmem device,
+ if unspecified, default values shall be used.
+
+ nvmem-cell-names:
+ items:
+ - const: calibration-data
+
+ drive-strength-microamp:
+ description: adjust driving current
+ multipleOf: 200
+ minimum: 2000
+ maximum: 6000
+ default: 4600
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-output-names
+ - "#phy-cells"
+ - "#clock-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt8173-clk.h>
+ dsi-phy@10215000 {
+ compatible = "mediatek,mt8173-mipi-tx";
+ reg = <0x10215000 0x1000>;
+ clocks = <&clk26m>;
+ clock-output-names = "mipi_tx0_pll";
+ drive-strength-microamp = <4000>;
+ nvmem-cells= <&mipi_tx_calibration>;
+ nvmem-cell-names = "calibration-data";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/phy/mediatek,hdmi-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,hdmi-phy.yaml
new file mode 100644
index 0000000..4752517
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/mediatek,hdmi-phy.yaml
@@ -0,0 +1,92 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/mediatek,hdmi-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek High Definition Multimedia Interface (HDMI) PHY binding
+
+maintainers:
+ - Chun-Kuang Hu <chunkuang.hu@kernel.org>
+ - Philipp Zabel <p.zabel@pengutronix.de>
+ - Chunfeng Yun <chunfeng.yun@mediatek.com>
+
+description: |
+ The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
+ output and drives the HDMI pads.
+
+properties:
+ $nodename:
+ pattern: "^hdmi-phy@[0-9a-f]+$"
+
+ compatible:
+ enum:
+ - mediatek,mt2701-hdmi-phy
+ - mediatek,mt7623-hdmi-phy
+ - mediatek,mt8173-hdmi-phy
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: PLL reference clock
+
+ clock-names:
+ items:
+ - const: pll_ref
+
+ clock-output-names:
+ items:
+ - const: hdmitx_dig_cts
+
+ "#phy-cells":
+ const: 0
+
+ "#clock-cells":
+ const: 0
+
+ mediatek,ibias:
+ description:
+ TX DRV bias current for < 1.65Gbps
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 63
+ default: 0xa
+
+ mediatek,ibias_up:
+ description:
+ TX DRV bias current for >= 1.65Gbps
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 63
+ default: 0x1c
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - clock-output-names
+ - "#phy-cells"
+ - "#clock-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt8173-clk.h>
+ hdmi_phy: hdmi-phy@10209100 {
+ compatible = "mediatek,mt8173-hdmi-phy";
+ reg = <0x10209100 0x24>;
+ clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
+ clock-names = "pll_ref";
+ clock-output-names = "hdmitx_dig_cts";
+ mediatek,ibias = <0xa>;
+ mediatek,ibias_up = <0x1c>;
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
new file mode 100644
index 0000000..602e6ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -0,0 +1,260 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/mediatek,tphy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek T-PHY Controller Device Tree Bindings
+
+maintainers:
+ - Chunfeng Yun <chunfeng.yun@mediatek.com>
+
+description: |
+ The T-PHY controller supports physical layer functionality for a number of
+ controllers on MediaTek SoCs, includes USB2.0, USB3.0, PCIe and SATA.
+
+ Layout differences of banks between T-PHY V1 (mt8173/mt2701) and
+ T-PHY V2 (mt2712) when works on USB mode:
+ -----------------------------------
+ Version 1:
+ port offset bank
+ shared 0x0000 SPLLC
+ 0x0100 FMREG
+ u2 port0 0x0800 U2PHY_COM
+ u3 port0 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+ u2 port1 0x1000 U2PHY_COM
+ u3 port1 0x1100 U3PHYD
+ 0x1200 U3PHYD_BANK2
+ 0x1300 U3PHYA
+ 0x1400 U3PHYA_DA
+ u2 port2 0x1800 U2PHY_COM
+ ...
+
+ Version 2:
+ port offset bank
+ u2 port0 0x0000 MISC
+ 0x0100 FMREG
+ 0x0300 U2PHY_COM
+ u3 port0 0x0700 SPLLC
+ 0x0800 CHIP
+ 0x0900 U3PHYD
+ 0x0a00 U3PHYD_BANK2
+ 0x0b00 U3PHYA
+ 0x0c00 U3PHYA_DA
+ u2 port1 0x1000 MISC
+ 0x1100 FMREG
+ 0x1300 U2PHY_COM
+ u3 port1 0x1700 SPLLC
+ 0x1800 CHIP
+ 0x1900 U3PHYD
+ 0x1a00 U3PHYD_BANK2
+ 0x1b00 U3PHYA
+ 0x1c00 U3PHYA_DA
+ u2 port2 0x2000 MISC
+ ...
+
+ SPLLC shared by u3 ports and FMREG shared by u2 ports on V1 are put back
+ into each port; a new bank MISC for u2 ports and CHIP for u3 ports are
+ added on V2.
+
+properties:
+ $nodename:
+ pattern: "^t-phy@[0-9a-f]+$"
+
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - mediatek,mt2701-tphy
+ - mediatek,mt7623-tphy
+ - mediatek,mt7622-tphy
+ - mediatek,mt8516-tphy
+ - const: mediatek,generic-tphy-v1
+ - items:
+ - enum:
+ - mediatek,mt2712-tphy
+ - mediatek,mt7629-tphy
+ - mediatek,mt8183-tphy
+ - const: mediatek,generic-tphy-v2
+ - const: mediatek,mt2701-u3phy
+ deprecated: true
+ - const: mediatek,mt2712-u3phy
+ deprecated: true
+ - const: mediatek,mt8173-u3phy
+
+ reg:
+ description:
+ Register shared by multiple ports, exclude port's private register.
+ It is needed for T-PHY V1, such as mt2701 and mt8173, but not for
+ T-PHY V2, such as mt2712.
+ maxItems: 1
+
+ "#address-cells":
+ enum: [1, 2]
+
+ "#size-cells":
+ enum: [1, 2]
+
+ # Used with non-empty value if optional 'reg' is not provided.
+ # The format of the value is an arbitrary number of triplets of
+ # (child-bus-address, parent-bus-address, length).
+ ranges: true
+
+ mediatek,src-ref-clk-mhz:
+ description:
+ Frequency of reference clock for slew rate calibrate
+ default: 26
+
+ mediatek,src-coef:
+ description:
+ Coefficient for slew rate calibrate, depends on SoC process
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 28
+
+# Required child node:
+patternProperties:
+ "^usb-phy@[0-9a-f]+$":
+ type: object
+ description:
+ A sub-node is required for each port the controller provides.
+ Address range information including the usual 'reg' property
+ is used inside these nodes to describe the controller's topology.
+
+ properties:
+ reg:
+ maxItems: 1
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+ items:
+ - description: Reference clock, (HS is 48Mhz, SS/P is 24~27Mhz)
+ - description: Reference clock of analog phy
+ description:
+ Uses both clocks if the clock of analog and digital phys are
+ separated, otherwise uses "ref" clock only if needed.
+
+ clock-names:
+ minItems: 1
+ maxItems: 2
+ items:
+ - const: ref
+ - const: da_ref
+
+ "#phy-cells":
+ const: 1
+ description: |
+ The cells contain the following arguments.
+
+ - description: The PHY type
+ enum:
+ - PHY_TYPE_USB2
+ - PHY_TYPE_USB3
+ - PHY_TYPE_PCIE
+ - PHY_TYPE_SATA
+
+ # The following optional vendor properties are only for debug or HQA test
+ mediatek,eye-src:
+ description:
+ The value of slew rate calibrate (U2 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 7
+
+ mediatek,eye-vrt:
+ description:
+ The selection of VRT reference voltage (U2 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 7
+
+ mediatek,eye-term:
+ description:
+ The selection of HS_TX TERM reference voltage (U2 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 7
+
+ mediatek,intr:
+ description:
+ The selection of internal resistor (U2 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 31
+
+ mediatek,discth:
+ description:
+ The selection of disconnect threshold (U2 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 15
+
+ mediatek,bc12:
+ description:
+ Specify the flag to enable BC1.2 if support it
+ type: boolean
+
+ required:
+ - reg
+ - "#phy-cells"
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - "#address-cells"
+ - "#size-cells"
+ - ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt8173-clk.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/phy/phy.h>
+ usb@11271000 {
+ compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3";
+ reg = <0x11271000 0x3000>, <0x11280700 0x0100>;
+ reg-names = "mac", "ippc";
+ phys = <&u2port0 PHY_TYPE_USB2>,
+ <&u3port0 PHY_TYPE_USB3>,
+ <&u2port1 PHY_TYPE_USB2>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>;
+ clock-names = "sys_ck";
+ };
+
+ t-phy@11290000 {
+ compatible = "mediatek,mt8173-u3phy";
+ reg = <0x11290000 0x800>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ u2port0: usb-phy@11290800 {
+ reg = <0x11290800 0x100>;
+ clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>, <&clk48m>;
+ clock-names = "ref", "da_ref";
+ #phy-cells = <1>;
+ };
+
+ u3port0: usb-phy@11290900 {
+ reg = <0x11290900 0x700>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ };
+
+ u2port1: usb-phy@11291000 {
+ reg = <0x11291000 0x100>;
+ #phy-cells = <1>;
+ };
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/phy/mediatek,ufs-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,ufs-phy.yaml
new file mode 100644
index 0000000..3a9be82e
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/mediatek,ufs-phy.yaml
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/mediatek,ufs-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek Universal Flash Storage (UFS) M-PHY binding
+
+maintainers:
+ - Stanley Chu <stanley.chu@mediatek.com>
+ - Chunfeng Yun <chunfeng.yun@mediatek.com>
+
+description: |
+ UFS M-PHY nodes are defined to describe on-chip UFS M-PHY hardware macro.
+ Each UFS M-PHY node should have its own node.
+ To bind UFS M-PHY with UFS host controller, the controller node should
+ contain a phandle reference to UFS M-PHY node.
+
+properties:
+ $nodename:
+ pattern: "^ufs-phy@[0-9a-f]+$"
+
+ compatible:
+ const: mediatek,mt8183-ufsphy
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Unipro core control clock.
+ - description: M-PHY core control clock.
+
+ clock-names:
+ items:
+ - const: unipro
+ - const: mp
+
+ "#phy-cells":
+ const: 0
+
+required:
+ - compatible
+ - reg
+ - "#phy-cells"
+ - clocks
+ - clock-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt8183-clk.h>
+ ufsphy: ufs-phy@11fa0000 {
+ compatible = "mediatek,mt8183-ufsphy";
+ reg = <0x11fa0000 0xc000>;
+ clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>,
+ <&infracfg CLK_INFRA_UFS_MP_SAP_BCLK>;
+ clock-names = "unipro", "mp";
+ #phy-cells = <0>;
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/phy/mediatek,xsphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,xsphy.yaml
new file mode 100644
index 0000000..598fd2b
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/mediatek,xsphy.yaml
@@ -0,0 +1,199 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/mediatek,xsphy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek XS-PHY Controller Device Tree Bindings
+
+maintainers:
+ - Chunfeng Yun <chunfeng.yun@mediatek.com>
+
+description: |
+ The XS-PHY controller supports physical layer functionality for USB3.1
+ GEN2 controller on MediaTek SoCs.
+
+ Banks layout of xsphy
+ ----------------------------------
+ port offset bank
+ u2 port0 0x0000 MISC
+ 0x0100 FMREG
+ 0x0300 U2PHY_COM
+ u2 port1 0x1000 MISC
+ 0x1100 FMREG
+ 0x1300 U2PHY_COM
+ u2 port2 0x2000 MISC
+ ...
+ u31 common 0x3000 DIG_GLB
+ 0x3100 PHYA_GLB
+ u31 port0 0x3400 DIG_LN_TOP
+ 0x3500 DIG_LN_TX0
+ 0x3600 DIG_LN_RX0
+ 0x3700 DIG_LN_DAIF
+ 0x3800 PHYA_LN
+ u31 port1 0x3a00 DIG_LN_TOP
+ 0x3b00 DIG_LN_TX0
+ 0x3c00 DIG_LN_RX0
+ 0x3d00 DIG_LN_DAIF
+ 0x3e00 PHYA_LN
+ ...
+ DIG_GLB & PHYA_GLB are shared by U31 ports.
+
+properties:
+ $nodename:
+ pattern: "^xs-phy@[0-9a-f]+$"
+
+ compatible:
+ items:
+ - enum:
+ - mediatek,mt3611-xsphy
+ - mediatek,mt3612-xsphy
+ - const: mediatek,xsphy
+
+ reg:
+ description:
+ Register shared by multiple U3 ports, exclude port's private register,
+ if only U2 ports provided, shouldn't use the property.
+ maxItems: 1
+
+ "#address-cells":
+ enum: [1, 2]
+
+ "#size-cells":
+ enum: [1, 2]
+
+ ranges: true
+
+ mediatek,src-ref-clk-mhz:
+ description:
+ Frequency of reference clock for slew rate calibrate
+ default: 26
+
+ mediatek,src-coef:
+ description:
+ Coefficient for slew rate calibrate, depends on SoC process
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 17
+
+# Required child node:
+patternProperties:
+ "^usb-phy@[0-9a-f]+$":
+ type: object
+ description:
+ A sub-node is required for each port the controller provides.
+ Address range information including the usual 'reg' property
+ is used inside these nodes to describe the controller's topology.
+
+ properties:
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Reference clock, (HS is 48Mhz, SS/P is 24~27Mhz)
+
+ clock-names:
+ items:
+ - const: ref
+
+ "#phy-cells":
+ const: 1
+ description: |
+ The cells contain the following arguments.
+
+ - description: The PHY type
+ enum:
+ - PHY_TYPE_USB2
+ - PHY_TYPE_USB3
+
+ # The following optional vendor properties are only for debug or HQA test
+ mediatek,eye-src:
+ description:
+ The value of slew rate calibrate (U2 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 7
+
+ mediatek,eye-vrt:
+ description:
+ The selection of VRT reference voltage (U2 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 7
+
+ mediatek,eye-term:
+ description:
+ The selection of HS_TX TERM reference voltage (U2 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 7
+
+ mediatek,efuse-intr:
+ description:
+ The selection of Internal Resistor (U2/U3 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 63
+
+ mediatek,efuse-tx-imp:
+ description:
+ The selection of TX Impedance (U3 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 31
+
+ mediatek,efuse-rx-imp:
+ description:
+ The selection of RX Impedance (U3 phy)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 31
+
+ required:
+ - reg
+ - clocks
+ - clock-names
+ - "#phy-cells"
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - "#address-cells"
+ - "#size-cells"
+ - ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/phy/phy.h>
+
+ u3phy: xs-phy@11c40000 {
+ compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy";
+ reg = <0x11c43000 0x0200>;
+ mediatek,src-ref-clk-mhz = <26>;
+ mediatek,src-coef = <17>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ u2port0: usb-phy@11c40000 {
+ reg = <0x11c40000 0x0400>;
+ clocks = <&clk48m>;
+ clock-names = "ref";
+ mediatek,eye-src = <4>;
+ #phy-cells = <1>;
+ };
+
+ u3port0: usb-phy@11c43000 {
+ reg = <0x11c43400 0x0500>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ mediatek,efuse-intr = <28>;
+ #phy-cells = <1>;
+ };
+ };
+
+...
diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt
deleted file mode 100644
index dd75b67..0000000
--- a/Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt
+++ /dev/null
@@ -1,162 +0,0 @@
-MediaTek T-PHY binding
---------------------------
-
-T-phy controller supports physical layer functionality for a number of
-controllers on MediaTek SoCs, such as, USB2.0, USB3.0, PCIe, and SATA.
-
-Required properties (controller (parent) node):
- - compatible : should be one of
- "mediatek,generic-tphy-v1"
- "mediatek,generic-tphy-v2"
- "mediatek,mt2701-u3phy" (deprecated)
- "mediatek,mt2712-u3phy" (deprecated)
- "mediatek,mt8173-u3phy";
- make use of "mediatek,generic-tphy-v1" on mt2701 instead and
- "mediatek,generic-tphy-v2" on mt2712 instead.
-
-- #address-cells: the number of cells used to represent physical
- base addresses.
-- #size-cells: the number of cells used to represent the size of an address.
-- ranges: the address mapping relationship to the parent, defined with
- - empty value: if optional 'reg' is used.
- - non-empty value: if optional 'reg' is not used. should set
- the child's base address to 0, the physical address
- within parent's address space, and the length of
- the address map.
-
-Required nodes : a sub-node is required for each port the controller
- provides. Address range information including the usual
- 'reg' property is used inside these nodes to describe
- the controller's topology.
-
-Optional properties (controller (parent) node):
- - reg : offset and length of register shared by multiple ports,
- exclude port's private register. It is needed on mt2701
- and mt8173, but not on mt2712.
- - mediatek,src-ref-clk-mhz : frequency of reference clock for slew rate
- calibrate
- - mediatek,src-coef : coefficient for slew rate calibrate, depends on
- SoC process
-
-Required properties (port (child) node):
-- reg : address and length of the register set for the port.
-- #phy-cells : should be 1 (See second example)
- cell after port phandle is phy type from:
- - PHY_TYPE_USB2
- - PHY_TYPE_USB3
- - PHY_TYPE_PCIE
- - PHY_TYPE_SATA
-
-Optional properties (PHY_TYPE_USB2 port (child) node):
-- clocks : a list of phandle + clock-specifier pairs, one for each
- entry in clock-names
-- clock-names : may contain
- "ref": 48M reference clock for HighSpeed (digital) phy; and 26M
- reference clock for SuperSpeed (digital) phy, sometimes is
- 24M, 25M or 27M, depended on platform.
- "da_ref": the reference clock of analog phy, used if the clocks
- of analog and digital phys are separated, otherwise uses
- "ref" clock only if needed.
-
-- mediatek,eye-src : u32, the value of slew rate calibrate
-- mediatek,eye-vrt : u32, the selection of VRT reference voltage
-- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage
-- mediatek,bc12 : bool, enable BC12 of u2phy if support it
-- mediatek,discth : u32, the selection of disconnect threshold
-- mediatek,intr : u32, the selection of internal R (resistance)
-
-Example:
-
-u3phy: usb-phy@11290000 {
- compatible = "mediatek,mt8173-u3phy";
- reg = <0 0x11290000 0 0x800>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- u2port0: usb-phy@11290800 {
- reg = <0 0x11290800 0 0x100>;
- clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
- clock-names = "ref";
- #phy-cells = <1>;
- };
-
- u3port0: usb-phy@11290900 {
- reg = <0 0x11290800 0 0x700>;
- clocks = <&clk26m>;
- clock-names = "ref";
- #phy-cells = <1>;
- };
-
- u2port1: usb-phy@11291000 {
- reg = <0 0x11291000 0 0x100>;
- clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
- clock-names = "ref";
- #phy-cells = <1>;
- };
-};
-
-Specifying phy control of devices
----------------------------------
-
-Device nodes should specify the configuration required in their "phys"
-property, containing a phandle to the phy port node and a device type;
-phy-names for each port are optional.
-
-Example:
-
-#include <dt-bindings/phy/phy.h>
-
-usb30: usb@11270000 {
- ...
- phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
- phy-names = "usb2-0", "usb3-0";
- ...
-};
-
-
-Layout differences of banks between mt8173/mt2701 and mt2712
--------------------------------------------------------------
-mt8173 and mt2701:
-port offset bank
-shared 0x0000 SPLLC
- 0x0100 FMREG
-u2 port0 0x0800 U2PHY_COM
-u3 port0 0x0900 U3PHYD
- 0x0a00 U3PHYD_BANK2
- 0x0b00 U3PHYA
- 0x0c00 U3PHYA_DA
-u2 port1 0x1000 U2PHY_COM
-u3 port1 0x1100 U3PHYD
- 0x1200 U3PHYD_BANK2
- 0x1300 U3PHYA
- 0x1400 U3PHYA_DA
-u2 port2 0x1800 U2PHY_COM
- ...
-
-mt2712:
-port offset bank
-u2 port0 0x0000 MISC
- 0x0100 FMREG
- 0x0300 U2PHY_COM
-u3 port0 0x0700 SPLLC
- 0x0800 CHIP
- 0x0900 U3PHYD
- 0x0a00 U3PHYD_BANK2
- 0x0b00 U3PHYA
- 0x0c00 U3PHYA_DA
-u2 port1 0x1000 MISC
- 0x1100 FMREG
- 0x1300 U2PHY_COM
-u3 port1 0x1700 SPLLC
- 0x1800 CHIP
- 0x1900 U3PHYD
- 0x1a00 U3PHYD_BANK2
- 0x1b00 U3PHYA
- 0x1c00 U3PHYA_DA
-u2 port2 0x2000 MISC
- ...
-
- SPLLC shared by u3 ports and FMREG shared by u2 ports on
-mt8173/mt2701 are put back into each port; a new bank MISC for
-u2 ports and CHIP for u3 ports are added on mt2712.
diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-ufs.txt b/Documentation/devicetree/bindings/phy/phy-mtk-ufs.txt
deleted file mode 100644
index 5789029..0000000
--- a/Documentation/devicetree/bindings/phy/phy-mtk-ufs.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-MediaTek Universal Flash Storage (UFS) M-PHY binding
---------------------------------------------------------
-
-UFS M-PHY nodes are defined to describe on-chip UFS M-PHY hardware macro.
-Each UFS M-PHY node should have its own node.
-
-To bind UFS M-PHY with UFS host controller, the controller node should
-contain a phandle reference to UFS M-PHY node.
-
-Required properties for UFS M-PHY nodes:
-- compatible : Compatible list, contains the following controller:
- "mediatek,mt8183-ufsphy" for ufs phy
- persent on MT81xx chipsets.
-- reg : Address and length of the UFS M-PHY register set.
-- #phy-cells : This property shall be set to 0.
-- clocks : List of phandle and clock specifier pairs.
-- clock-names : List of clock input name strings sorted in the same
- order as the clocks property. Following clocks are
- mandatory.
- "unipro": Unipro core control clock.
- "mp": M-PHY core control clock.
-
-Example:
-
- ufsphy: phy@11fa0000 {
- compatible = "mediatek,mt8183-ufsphy";
- reg = <0 0x11fa0000 0 0xc000>;
- #phy-cells = <0>;
-
- clocks = <&infracfg_ao INFRACFG_AO_UNIPRO_SCK_CG>,
- <&infracfg_ao INFRACFG_AO_UFS_MP_SAP_BCLK_CG>;
- clock-names = "unipro", "mp";
- };
-
- ufshci@11270000 {
- ...
- phys = <&ufsphy>;
- };
diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
deleted file mode 100644
index e7caefa..0000000
--- a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt
+++ /dev/null
@@ -1,109 +0,0 @@
-MediaTek XS-PHY binding
---------------------------
-
-The XS-PHY controller supports physical layer functionality for USB3.1
-GEN2 controller on MediaTek SoCs.
-
-Required properties (controller (parent) node):
- - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy",
- soc-model is the name of SoC, such as mt3611 etc;
- when using "mediatek,xsphy" compatible string, you need SoC specific
- ones in addition, one of:
- - "mediatek,mt3611-xsphy"
-
- - #address-cells, #size-cells : should use the same values as the root node
- - ranges: must be present
-
-Optional properties (controller (parent) node):
- - reg : offset and length of register shared by multiple U3 ports,
- exclude port's private register, if only U2 ports provided,
- shouldn't use the property.
- - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate
- calibrate
- - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on
- SoC process
-
-Required nodes : a sub-node is required for each port the controller
- provides. Address range information including the usual
- 'reg' property is used inside these nodes to describe
- the controller's topology.
-
-Required properties (port (child) node):
-- reg : address and length of the register set for the port.
-- clocks : a list of phandle + clock-specifier pairs, one for each
- entry in clock-names
-- clock-names : must contain
- "ref": 48M reference clock for HighSpeed analog phy; and 26M
- reference clock for SuperSpeedPlus analog phy, sometimes is
- 24M, 25M or 27M, depended on platform.
-- #phy-cells : should be 1
- cell after port phandle is phy type from:
- - PHY_TYPE_USB2
- - PHY_TYPE_USB3
-
-The following optional properties are only for debug or HQA test
-Optional properties (PHY_TYPE_USB2 port (child) node):
-- mediatek,eye-src : u32, the value of slew rate calibrate
-- mediatek,eye-vrt : u32, the selection of VRT reference voltage
-- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage
-- mediatek,efuse-intr : u32, the selection of Internal Resistor
-
-Optional properties (PHY_TYPE_USB3 port (child) node):
-- mediatek,efuse-intr : u32, the selection of Internal Resistor
-- mediatek,efuse-tx-imp : u32, the selection of TX Impedance
-- mediatek,efuse-rx-imp : u32, the selection of RX Impedance
-
-Banks layout of xsphy
--------------------------------------------------------------
-port offset bank
-u2 port0 0x0000 MISC
- 0x0100 FMREG
- 0x0300 U2PHY_COM
-u2 port1 0x1000 MISC
- 0x1100 FMREG
- 0x1300 U2PHY_COM
-u2 port2 0x2000 MISC
- ...
-u31 common 0x3000 DIG_GLB
- 0x3100 PHYA_GLB
-u31 port0 0x3400 DIG_LN_TOP
- 0x3500 DIG_LN_TX0
- 0x3600 DIG_LN_RX0
- 0x3700 DIG_LN_DAIF
- 0x3800 PHYA_LN
-u31 port1 0x3a00 DIG_LN_TOP
- 0x3b00 DIG_LN_TX0
- 0x3c00 DIG_LN_RX0
- 0x3d00 DIG_LN_DAIF
- 0x3e00 PHYA_LN
- ...
-
-DIG_GLB & PHYA_GLB are shared by U31 ports.
-
-Example:
-
-u3phy: usb-phy@11c40000 {
- compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy";
- reg = <0 0x11c43000 0 0x0200>;
- mediatek,src-ref-clk-mhz = <26>;
- mediatek,src-coef = <17>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- u2port0: usb-phy@11c40000 {
- reg = <0 0x11c40000 0 0x0400>;
- clocks = <&clk48m>;
- clock-names = "ref";
- mediatek,eye-src = <4>;
- #phy-cells = <1>;
- };
-
- u3port0: usb-phy@11c43000 {
- reg = <0 0x11c43400 0 0x0500>;
- clocks = <&clk26m>;
- clock-names = "ref";
- mediatek,efuse-intr = <28>;
- #phy-cells = <1>;
- };
-};
diff --git a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
index 0ba6197..46df678 100644
--- a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
@@ -45,6 +45,12 @@
"#size-cells":
const: 0
+ vdda1v1-supply:
+ description: regulator providing 1V1 power supply to the PLL block
+
+ vdda1v8-supply:
+ description: regulator providing 1V8 power supply to the PLL block
+
#Required child nodes:
patternProperties:
@@ -61,12 +67,6 @@
phy-supply:
description: regulator providing 3V3 power supply to the PHY.
- vdda1v1-supply:
- description: regulator providing 1V1 power supply to the PLL block
-
- vdda1v8-supply:
- description: regulator providing 1V8 power supply to the PLL block
-
"#phy-cells":
enum: [ 0x0, 0x1 ]
@@ -90,8 +90,6 @@
required:
- reg
- phy-supply
- - vdda1v1-supply
- - vdda1v8-supply
- "#phy-cells"
additionalProperties: false
@@ -102,6 +100,8 @@
- clocks
- "#address-cells"
- "#size-cells"
+ - vdda1v1-supply
+ - vdda1v8-supply
- usb-phy@0
- usb-phy@1
@@ -116,22 +116,20 @@
reg = <0x5a006000 0x1000>;
clocks = <&rcc USBPHY_K>;
resets = <&rcc USBPHY_R>;
+ vdda1v1-supply = <®11>;
+ vdda1v8-supply = <®18>;
#address-cells = <1>;
#size-cells = <0>;
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
#phy-cells = <0>;
};
usbphyc_port1: usb-phy@1 {
reg = <1>;
phy-supply = <&vdd_usb>;
- vdda1v1-supply = <®11>;
- vdda1v8-supply = <®18>;
#phy-cells = <1>;
};
};
diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
index ec05db3..626447f 100644
--- a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
@@ -25,19 +25,32 @@
- qcom,msm8998-qmp-pcie-phy
- qcom,msm8998-qmp-ufs-phy
- qcom,msm8998-qmp-usb3-phy
+ - qcom,sc8180x-qmp-ufs-phy
+ - qcom,sc8180x-qmp-usb3-phy
- qcom,sdm845-qhp-pcie-phy
- qcom,sdm845-qmp-pcie-phy
- qcom,sdm845-qmp-ufs-phy
- qcom,sdm845-qmp-usb3-uni-phy
- qcom,sm8150-qmp-ufs-phy
+ - qcom,sm8150-qmp-usb3-phy
+ - qcom,sm8150-qmp-usb3-uni-phy
- qcom,sm8250-qmp-ufs-phy
- qcom,sm8250-qmp-gen3x1-pcie-phy
- qcom,sm8250-qmp-gen3x2-pcie-phy
- qcom,sm8250-qmp-modem-pcie-phy
+ - qcom,sm8250-qmp-usb3-phy
+ - qcom,sm8250-qmp-usb3-uni-phy
+ - qcom,sm8350-qmp-ufs-phy
+ - qcom,sm8350-qmp-usb3-phy
+ - qcom,sm8350-qmp-usb3-uni-phy
+ - qcom,sdx55-qmp-usb3-uni-phy
reg:
+ minItems: 1
+ maxItems: 2
items:
- description: Address and length of PHY's common serdes block.
+ - description: Address and length of PHY's DP_COM control block.
"#clock-cells":
enum: [ 1, 2 ]
@@ -136,6 +149,32 @@
compatible:
contains:
enum:
+ - qcom,sdx55-qmp-usb3-uni-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: Phy aux clock.
+ - description: Phy config clock.
+ - description: 19.2 MHz ref clk.
+ clock-names:
+ items:
+ - const: aux
+ - const: cfg_ahb
+ - const: ref
+ resets:
+ items:
+ - description: reset of phy block.
+ - description: phy common block reset.
+ reset-names:
+ items:
+ - const: phy
+ - const: common
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
- qcom,msm8996-qmp-pcie-phy
then:
properties:
@@ -285,6 +324,64 @@
reset-names:
items:
- const: phy
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,sm8150-qmp-usb3-phy
+ - qcom,sm8150-qmp-usb3-uni-phy
+ - qcom,sm8250-qmp-usb3-uni-phy
+ - qcom,sm8350-qmp-usb3-uni-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: Phy aux clock.
+ - description: 19.2 MHz ref clk source.
+ - description: 19.2 MHz ref clk.
+ - description: Phy common block aux clock.
+ clock-names:
+ items:
+ - const: aux
+ - const: ref_clk_src
+ - const: ref
+ - const: com_aux
+ resets:
+ items:
+ - description: reset of phy block.
+ - description: phy common block reset.
+ reset-names:
+ items:
+ - const: phy
+ - const: common
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,sm8250-qmp-usb3-phy
+ - qcom,sm8350-qmp-usb3-phy
+ then:
+ properties:
+ clocks:
+ items:
+ - description: Phy aux clock.
+ - description: 19.2 MHz ref clk.
+ - description: Phy common block aux clock.
+ clock-names:
+ items:
+ - const: aux
+ - const: ref_clk_src
+ - const: com_aux
+ resets:
+ items:
+ - description: reset of phy block.
+ - description: phy common block reset.
+ reset-names:
+ items:
+ - const: phy
+ - const: common
examples:
- |
diff --git a/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml
index d457fb6..9f9cf07 100644
--- a/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml
@@ -21,6 +21,8 @@
- qcom,ipq8074-qusb2-phy
- qcom,msm8996-qusb2-phy
- qcom,msm8998-qusb2-phy
+ - qcom,sdm660-qusb2-phy
+ - qcom,ipq6018-qusb2-phy
- items:
- enum:
- qcom,sc7180-qusb2-phy
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml
index ca6a083..abcc437 100644
--- a/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml
@@ -16,6 +16,7 @@
compatible:
enum:
- qcom,usb-hs-28nm-femtophy
+ - qcom,usb-hs-28nm-mdm9607
reg:
maxItems: 1
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
index 4949a28..ee77c64 100644
--- a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml
@@ -17,6 +17,8 @@
enum:
- qcom,usb-snps-hs-7nm-phy
- qcom,sm8150-usb-hs-phy
+ - qcom,sm8250-usb-hs-phy
+ - qcom,sm8350-usb-hs-phy
- qcom,usb-snps-femto-v2-phy
reg:
diff --git a/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml b/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml
index c33e9bc..bbbd855 100644
--- a/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml
+++ b/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml
@@ -151,7 +151,7 @@
WIZ node should have '1' subnode for the SERDES. It could be either
Sierra SERDES or Torrent SERDES. Sierra SERDES should follow the
bindings specified in
- Documentation/devicetree/bindings/phy/phy-cadence-sierra.txt
+ Documentation/devicetree/bindings/phy/phy-cadence-sierra.yaml
Torrent SERDES should follow the bindings specified in
Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml
diff --git a/drivers/phy/broadcom/Kconfig b/drivers/phy/broadcom/Kconfig
index a1f1a9c..0925633 100644
--- a/drivers/phy/broadcom/Kconfig
+++ b/drivers/phy/broadcom/Kconfig
@@ -91,10 +91,11 @@
config PHY_BRCM_USB
tristate "Broadcom STB USB PHY driver"
- depends on ARCH_BRCMSTB || COMPILE_TEST
+ depends on ARCH_BCM4908 || ARCH_BRCMSTB || COMPILE_TEST
depends on OF
select GENERIC_PHY
select SOC_BRCMSTB
+ default ARCH_BCM4908
default ARCH_BRCMSTB
help
Enable this to support the Broadcom STB USB PHY.
diff --git a/drivers/phy/broadcom/phy-brcm-usb.c b/drivers/phy/broadcom/phy-brcm-usb.c
index 99fbc7e..116fb23 100644
--- a/drivers/phy/broadcom/phy-brcm-usb.c
+++ b/drivers/phy/broadcom/phy-brcm-usb.c
@@ -11,6 +11,7 @@
#include <linux/io.h>
#include <linux/module.h>
#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
@@ -34,7 +35,7 @@ struct value_to_name_map {
};
struct match_chip_info {
- void *init_func;
+ void (*init_func)(struct brcm_usb_init_params *params);
u8 required_regs[BRCM_REGS_MAX + 1];
u8 optional_reg;
};
@@ -286,6 +287,10 @@ static const struct match_chip_info chip_info_7445 = {
static const struct of_device_id brcm_usb_dt_ids[] = {
{
+ .compatible = "brcm,bcm4908-usb-phy",
+ .data = &chip_info_7445,
+ },
+ {
.compatible = "brcm,bcm7216-usb-phy",
.data = &chip_info_7216,
},
@@ -427,8 +432,6 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
struct device_node *dn = pdev->dev.of_node;
int err;
const char *mode;
- const struct of_device_id *match;
- void (*dvr_init)(struct brcm_usb_init_params *params);
const struct match_chip_info *info;
struct regmap *rmap;
int x;
@@ -441,10 +444,11 @@ static int brcm_usb_phy_probe(struct platform_device *pdev)
priv->ini.family_id = brcmstb_get_family_id();
priv->ini.product_id = brcmstb_get_product_id();
- match = of_match_node(brcm_usb_dt_ids, dev->of_node);
- info = match->data;
- dvr_init = info->init_func;
- (*dvr_init)(&priv->ini);
+ info = of_device_get_match_data(&pdev->dev);
+ if (!info)
+ return -ENOENT;
+
+ info->init_func(&priv->ini);
dev_dbg(dev, "Best mapping table is for %s\n",
priv->ini.family_name);
diff --git a/drivers/phy/cadence/phy-cadence-torrent.c b/drivers/phy/cadence/phy-cadence-torrent.c
index f310e15..591a158 100644
--- a/drivers/phy/cadence/phy-cadence-torrent.c
+++ b/drivers/phy/cadence/phy-cadence-torrent.c
@@ -2298,6 +2298,7 @@ static int cdns_torrent_phy_probe(struct platform_device *pdev)
if (total_num_lanes > MAX_NUM_LANES) {
dev_err(dev, "Invalid lane configuration\n");
+ ret = -EINVAL;
goto put_lnk_rst;
}
diff --git a/drivers/phy/ingenic/phy-ingenic-usb.c b/drivers/phy/ingenic/phy-ingenic-usb.c
index 4d1587d..ea127b1 100644
--- a/drivers/phy/ingenic/phy-ingenic-usb.c
+++ b/drivers/phy/ingenic/phy-ingenic-usb.c
@@ -82,18 +82,7 @@
#define USBPCR1_PORT_RST BIT(21)
#define USBPCR1_WORD_IF_16BIT BIT(19)
-enum ingenic_usb_phy_version {
- ID_JZ4770,
- ID_JZ4775,
- ID_JZ4780,
- ID_X1000,
- ID_X1830,
- ID_X2000,
-};
-
struct ingenic_soc_info {
- enum ingenic_usb_phy_version version;
-
void (*usb_phy_init)(struct phy *phy);
};
@@ -300,38 +289,26 @@ static void x2000_usb_phy_init(struct phy *phy)
}
static const struct ingenic_soc_info jz4770_soc_info = {
- .version = ID_JZ4770,
-
.usb_phy_init = jz4770_usb_phy_init,
};
static const struct ingenic_soc_info jz4775_soc_info = {
- .version = ID_JZ4775,
-
.usb_phy_init = jz4775_usb_phy_init,
};
static const struct ingenic_soc_info jz4780_soc_info = {
- .version = ID_JZ4780,
-
.usb_phy_init = jz4780_usb_phy_init,
};
static const struct ingenic_soc_info x1000_soc_info = {
- .version = ID_X1000,
-
.usb_phy_init = x1000_usb_phy_init,
};
static const struct ingenic_soc_info x1830_soc_info = {
- .version = ID_X1830,
-
.usb_phy_init = x1830_usb_phy_init,
};
static const struct ingenic_soc_info x2000_soc_info = {
- .version = ID_X2000,
-
.usb_phy_init = x2000_usb_phy_init,
};
diff --git a/drivers/phy/mediatek/phy-mtk-mipi-dsi.c b/drivers/phy/mediatek/phy-mtk-mipi-dsi.c
index 18c4812..eeb357bf 100644
--- a/drivers/phy/mediatek/phy-mtk-mipi-dsi.c
+++ b/drivers/phy/mediatek/phy-mtk-mipi-dsi.c
@@ -234,7 +234,7 @@ static const struct of_device_id mtk_mipi_tx_match[] = {
{ },
};
-struct platform_driver mtk_mipi_tx_driver = {
+static struct platform_driver mtk_mipi_tx_driver = {
.probe = mtk_mipi_tx_probe,
.remove = mtk_mipi_tx_remove,
.driver = {
diff --git a/drivers/phy/motorola/phy-cpcap-usb.c b/drivers/phy/motorola/phy-cpcap-usb.c
index 4728e2b..6ee478b 100644
--- a/drivers/phy/motorola/phy-cpcap-usb.c
+++ b/drivers/phy/motorola/phy-cpcap-usb.c
@@ -143,7 +143,7 @@ static bool cpcap_usb_vbus_valid(struct cpcap_phy_ddata *ddata)
error = iio_read_channel_processed(ddata->vbus, &value);
if (error >= 0)
- return value > 3900 ? true : false;
+ return value > 3900;
dev_err(ddata->dev, "error reading VBUS: %i\n", error);
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 0939a9e..9cdebe7 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -212,6 +212,15 @@ static const unsigned int qmp_v4_usb3_uniphy_regs_layout[QPHY_LAYOUT_SIZE] = {
[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x614,
};
+static const unsigned int sm8350_usb3_uniphy_regs_layout[QPHY_LAYOUT_SIZE] = {
+ [QPHY_SW_RESET] = 0x00,
+ [QPHY_START_CTRL] = 0x44,
+ [QPHY_PCS_STATUS] = 0x14,
+ [QPHY_PCS_POWER_DOWN_CONTROL] = 0x40,
+ [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x1008,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x1014,
+};
+
static const unsigned int sdm845_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
[QPHY_START_CTRL] = 0x00,
[QPHY_PCS_READY_STATUS] = 0x160,
@@ -1974,6 +1983,291 @@ static const struct qmp_phy_init_tbl sm8250_qmp_gen3x2_pcie_pcs_misc_tbl[] = {
QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG4, 0x07),
};
+static const struct qmp_phy_init_tbl sdx55_usb3_uniphy_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x20),
+ QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x08),
+};
+
+static const struct qmp_phy_init_tbl sdx55_usb3_uniphy_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x26),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xbf),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x048),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x09),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f),
+};
+
+static const struct qmp_phy_init_tbl sm8350_ufsphy_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_SYSCLK_EN_SEL, 0xd9),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_HSCLK_SEL, 0x11),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_HSCLK_HS_SWITCH_SEL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_LOCK_CMP_EN, 0x42),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_VCO_TUNE_MAP, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_PLL_IVCO, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_VCO_TUNE_INITVAL2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_BIN_VCOCAL_HSCLK_SEL, 0x11),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_CP_CTRL_MODE0, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_PLL_RCTRL_MODE0, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_PLL_CCTRL_MODE0, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_LOCK_CMP1_MODE0, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_LOCK_CMP2_MODE0, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0xac),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_DEC_START_MODE1, 0x98),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_CP_CTRL_MODE1, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_PLL_RCTRL_MODE1, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_PLL_CCTRL_MODE1, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_LOCK_CMP1_MODE1, 0x65),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_LOCK_CMP2_MODE1, 0x1e),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xdd),
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x23),
+
+ /* Rate B */
+ QMP_PHY_INIT_CFG(QSERDES_V5_COM_VCO_TUNE_MAP, 0x06),
+};
+
+static const struct qmp_phy_init_tbl sm8350_ufsphy_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_PWM_GEAR_1_DIVIDER_BAND0_1, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_PWM_GEAR_2_DIVIDER_BAND0_1, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_PWM_GEAR_3_DIVIDER_BAND0_1, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_PWM_GEAR_4_DIVIDER_BAND0_1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_1, 0xf5),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_3, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RES_CODE_LANE_OFFSET_TX, 0x09),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RES_CODE_LANE_OFFSET_RX, 0x09),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_TRAN_DRVR_EMP_EN, 0x0c),
+};
+
+static const struct qmp_phy_init_tbl sm8350_ufsphy_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_SIGDET_LVL, 0x24),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_SIGDET_CNTRL, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_SIGDET_DEGLITCH_CNTRL, 0x1e),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_BAND, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FASTLOCK_FO_GAIN, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5a),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_PI_CONTROLS, 0xf1),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_PI_CTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FO_GAIN, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SO_GAIN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_TERM_BW, 0x1b),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL1, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1a),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x17),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_IDAC_MEASURE_TIME, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_LOW, 0x6d),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH, 0x6d),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH2, 0xed),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH3, 0x3b),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH4, 0x3c),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_LOW, 0xe0),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH, 0xc8),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH2, 0xc8),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH3, 0x3b),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH4, 0xb7),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_10_LOW, 0xe0),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_10_HIGH, 0xc8),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_10_HIGH2, 0xc8),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_10_HIGH3, 0x3b),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_10_HIGH4, 0xb7),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_DCC_CTRL1, 0x0c),
+};
+
+static const struct qmp_phy_init_tbl sm8350_ufsphy_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_SIGDET_CTRL2, 0x6d),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0a),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_SMALL_AMP_DRV_LVL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_DEBUG_BUS_CLKSEL, 0x1f),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_MIN_HIBERN8_TIME, 0xff),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_PLL_CNTL, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TIMER_20US_CORECLK_STEPS_MSB, 0x16),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TIMER_20US_CORECLK_STEPS_LSB, 0xd8),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_PWM_GEAR_BAND, 0xaa),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_HS_GEAR_BAND, 0x06),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_RX_SIGDET_CTRL1, 0x0e),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
+};
+
+static const struct qmp_phy_init_tbl sm8350_usb3_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RES_CODE_LANE_TX, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RES_CODE_LANE_RX, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RES_CODE_LANE_OFFSET_TX, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RES_CODE_LANE_OFFSET_RX, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_1, 0x35),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_3, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_4, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_5, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_PI_QEC_CTRL, 0x21),
+};
+
+static const struct qmp_phy_init_tbl sm8350_usb3_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FO_GAIN, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SO_GAIN, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_PI_CONTROLS, 0x99),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SB2_THRESH1, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SB2_THRESH2, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SB2_GAIN1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SB2_GAIN2, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_VGA_CAL_CNTRL1, 0x54),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_VGA_CAL_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_SIGDET_CNTRL, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_LOW, 0xbb),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH, 0x7b),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH2, 0xbb),
+ QMP_PHY_INIT_CFG_LANE(QSERDES_V5_RX_RX_MODE_00_HIGH3, 0x3d, 1),
+ QMP_PHY_INIT_CFG_LANE(QSERDES_V5_RX_RX_MODE_00_HIGH3, 0x3c, 2),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH4, 0xdb),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_LOW, 0x64),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH, 0x24),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH2, 0xd2),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH3, 0x13),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH4, 0xa9),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_DFE_EN_TIMER, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_AUX_DATA_TCOARSE_TFINE, 0xa0),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_DCC_CTRL1, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_GM_CAL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_VTH_CODE, 0x10),
+};
+
+static const struct qmp_phy_init_tbl sm8350_usb3_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_USB3_RCVR_DTCT_DLY_U3_L, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_USB3_RCVR_DTCT_DLY_U3_H, 0x00),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xaa),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl sm8350_usb3_uniphy_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_1, 0xa5),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_2, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_3, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_LANE_MODE_4, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_PI_QEC_CTRL, 0x21),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RES_CODE_LANE_OFFSET_TX, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_V5_TX_RES_CODE_LANE_OFFSET_RX, 0x0e),
+};
+
+static const struct qmp_phy_init_tbl sm8350_usb3_uniphy_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH4, 0xdc),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH3, 0xbd),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH2, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_HIGH, 0x7f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_00_LOW, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH4, 0xa9),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH3, 0x7b),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH2, 0xe4),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_HIGH, 0x24),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_MODE_01_LOW, 0x64),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_PI_CONTROLS, 0x99),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SB2_THRESH1, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SB2_THRESH2, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SB2_GAIN1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SB2_GAIN2, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_FO_GAIN, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_VGA_CAL_CNTRL1, 0x54),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_VGA_CAL_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_SIGDET_CNTRL, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_UCDR_SO_GAIN, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_GM_CAL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V5_RX_SIGDET_ENABLES, 0x00),
+};
+
+static const struct qmp_phy_init_tbl sm8350_usb3_uniphy_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xaa),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2, 0x07),
+ QMP_PHY_INIT_CFG(QPHY_V5_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10),
+ QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+};
+
/* struct qmp_phy_cfg - per-PHY initialization config */
struct qmp_phy_cfg {
/* phy-type - PCIE/UFS/USB */
@@ -2183,6 +2477,11 @@ static const char * const sdm845_ufs_phy_clk_l[] = {
"ref", "ref_aux",
};
+/* usb3 phy on sdx55 doesn't have com_aux clock */
+static const char * const qmp_v4_sdx55_usbphy_clk_l[] = {
+ "aux", "cfg_ahb", "ref"
+};
+
/* list of resets */
static const char * const msm8996_pciephy_reset_l[] = {
"phy", "common", "cfg",
@@ -2824,6 +3123,117 @@ static const struct qmp_phy_cfg sm8250_usb3_uniphy_cfg = {
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
};
+static const struct qmp_phy_cfg sdx55_usb3_uniphy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = sm8150_usb3_uniphy_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl),
+ .tx_tbl = sdx55_usb3_uniphy_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sdx55_usb3_uniphy_tx_tbl),
+ .rx_tbl = sdx55_usb3_uniphy_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sdx55_usb3_uniphy_rx_tbl),
+ .pcs_tbl = sm8250_usb3_uniphy_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sm8250_usb3_uniphy_pcs_tbl),
+ .clk_list = qmp_v4_sdx55_usbphy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v4_sdx55_usbphy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = qmp_v4_usb3_uniphy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+};
+
+static const struct qmp_phy_cfg sm8350_ufsphy_cfg = {
+ .type = PHY_TYPE_UFS,
+ .nlanes = 2,
+
+ .serdes_tbl = sm8350_ufsphy_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sm8350_ufsphy_serdes_tbl),
+ .tx_tbl = sm8350_ufsphy_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sm8350_ufsphy_tx_tbl),
+ .rx_tbl = sm8350_ufsphy_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sm8350_ufsphy_rx_tbl),
+ .pcs_tbl = sm8350_ufsphy_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sm8350_ufsphy_pcs_tbl),
+ .clk_list = sdm845_ufs_phy_clk_l,
+ .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = sm8150_ufsphy_regs_layout,
+
+ .start_ctrl = SERDES_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .is_dual_lane_phy = true,
+};
+
+static const struct qmp_phy_cfg sm8350_usb3phy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = sm8150_usb3_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_serdes_tbl),
+ .tx_tbl = sm8350_usb3_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sm8350_usb3_tx_tbl),
+ .rx_tbl = sm8350_usb3_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sm8350_usb3_rx_tbl),
+ .pcs_tbl = sm8350_usb3_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sm8350_usb3_pcs_tbl),
+ .clk_list = qmp_v4_sm8250_usbphy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v4_sm8250_usbphy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = qmp_v4_usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+
+ .has_phy_dp_com_ctrl = true,
+ .is_dual_lane_phy = true,
+};
+
+static const struct qmp_phy_cfg sm8350_usb3_uniphy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = sm8150_usb3_uniphy_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl),
+ .tx_tbl = sm8350_usb3_uniphy_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sm8350_usb3_uniphy_tx_tbl),
+ .rx_tbl = sm8350_usb3_uniphy_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sm8350_usb3_uniphy_rx_tbl),
+ .pcs_tbl = sm8350_usb3_uniphy_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sm8350_usb3_uniphy_pcs_tbl),
+ .clk_list = qmp_v4_phy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v4_phy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = sm8350_usb3_uniphy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+};
+
static void qcom_qmp_phy_configure_lane(void __iomem *base,
const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
@@ -3135,7 +3545,7 @@ static int qcom_qmp_phy_configure_dp_phy(struct qmp_phy *qphy)
static int qcom_qmp_dp_phy_calibrate(struct phy *phy)
{
struct qmp_phy *qphy = phy_get_drvdata(phy);
- const u8 cfg1_settings[] = { 0x13, 0x23, 0x1d };
+ static const u8 cfg1_settings[] = { 0x13, 0x23, 0x1d };
u8 val;
qphy->dp_aux_cfg++;
@@ -4129,6 +4539,12 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
.compatible = "qcom,sc7180-qmp-usb3-dp-phy",
/* It's a combo phy */
}, {
+ .compatible = "qcom,sc8180x-qmp-ufs-phy",
+ .data = &sm8150_ufsphy_cfg,
+ }, {
+ .compatible = "qcom,sc8180x-qmp-usb3-phy",
+ .data = &sm8150_usb3phy_cfg,
+ }, {
.compatible = "qcom,sdm845-qhp-pcie-phy",
.data = &sdm845_qhp_pciephy_cfg,
}, {
@@ -4171,8 +4587,20 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
.compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy",
.data = &sm8250_qmp_gen3x2_pciephy_cfg,
}, {
+ .compatible = "qcom,sm8350-qmp-ufs-phy",
+ .data = &sm8350_ufsphy_cfg,
+ }, {
.compatible = "qcom,sm8250-qmp-modem-pcie-phy",
.data = &sm8250_qmp_gen3x2_pciephy_cfg,
+ }, {
+ .compatible = "qcom,sdx55-qmp-usb3-uni-phy",
+ .data = &sdx55_usb3_uniphy_cfg,
+ }, {
+ .compatible = "qcom,sm8350-qmp-usb3-phy",
+ .data = &sm8350_usb3phy_cfg,
+ }, {
+ .compatible = "qcom,sm8350-qmp-usb3-uni-phy",
+ .data = &sm8350_usb3_uniphy_cfg,
},
{ },
};
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index db92a46..71ce3aa 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -824,4 +824,151 @@
#define QPHY_V4_PCS_PCIE_PRESET_P10_PRE 0xbc
#define QPHY_V4_PCS_PCIE_PRESET_P10_POST 0xe0
+/* Only for QMP V5 PHY - QSERDES COM registers */
+#define QSERDES_V5_COM_PLL_IVCO 0x058
+#define QSERDES_V5_COM_CP_CTRL_MODE0 0x074
+#define QSERDES_V5_COM_CP_CTRL_MODE1 0x078
+#define QSERDES_V5_COM_PLL_RCTRL_MODE0 0x07c
+#define QSERDES_V5_COM_PLL_RCTRL_MODE1 0x080
+#define QSERDES_V5_COM_PLL_CCTRL_MODE0 0x084
+#define QSERDES_V5_COM_PLL_CCTRL_MODE1 0x088
+#define QSERDES_V5_COM_SYSCLK_EN_SEL 0x094
+#define QSERDES_V5_COM_LOCK_CMP_EN 0x0a4
+#define QSERDES_V5_COM_LOCK_CMP1_MODE0 0x0ac
+#define QSERDES_V5_COM_LOCK_CMP2_MODE0 0x0b0
+#define QSERDES_V5_COM_LOCK_CMP1_MODE1 0x0b4
+#define QSERDES_V5_COM_DEC_START_MODE0 0x0bc
+#define QSERDES_V5_COM_LOCK_CMP2_MODE1 0x0b8
+#define QSERDES_V5_COM_DEC_START_MODE1 0x0c4
+#define QSERDES_V5_COM_VCO_TUNE_MAP 0x10c
+#define QSERDES_V5_COM_VCO_TUNE_INITVAL2 0x124
+#define QSERDES_V5_COM_HSCLK_SEL 0x158
+#define QSERDES_V5_COM_HSCLK_HS_SWITCH_SEL 0x15c
+#define QSERDES_V5_COM_BIN_VCOCAL_CMP_CODE1_MODE0 0x1ac
+#define QSERDES_V5_COM_BIN_VCOCAL_CMP_CODE2_MODE0 0x1b0
+#define QSERDES_V5_COM_BIN_VCOCAL_CMP_CODE1_MODE1 0x1b4
+#define QSERDES_V5_COM_BIN_VCOCAL_HSCLK_SEL 0x1bc
+#define QSERDES_V5_COM_BIN_VCOCAL_CMP_CODE2_MODE1 0x1b8
+
+/* Only for QMP V5 PHY - TX registers */
+#define QSERDES_V5_TX_RES_CODE_LANE_TX 0x34
+#define QSERDES_V5_TX_RES_CODE_LANE_RX 0x38
+#define QSERDES_V5_TX_RES_CODE_LANE_OFFSET_TX 0x3c
+#define QSERDES_V5_TX_RES_CODE_LANE_OFFSET_RX 0x40
+#define QSERDES_V5_TX_LANE_MODE_1 0x84
+#define QSERDES_V5_TX_LANE_MODE_2 0x88
+#define QSERDES_V5_TX_LANE_MODE_3 0x8c
+#define QSERDES_V5_TX_LANE_MODE_4 0x90
+#define QSERDES_V5_TX_LANE_MODE_5 0x94
+#define QSERDES_V5_TX_RCV_DETECT_LVL_2 0xa4
+#define QSERDES_V5_TX_TRAN_DRVR_EMP_EN 0xc0
+#define QSERDES_V5_TX_PI_QEC_CTRL 0xe4
+#define QSERDES_V5_TX_PWM_GEAR_1_DIVIDER_BAND0_1 0x178
+#define QSERDES_V5_TX_PWM_GEAR_2_DIVIDER_BAND0_1 0x17c
+#define QSERDES_V5_TX_PWM_GEAR_3_DIVIDER_BAND0_1 0x180
+#define QSERDES_V5_TX_PWM_GEAR_4_DIVIDER_BAND0_1 0x184
+
+/* Only for QMP V5 PHY - RX registers */
+#define QSERDES_V5_RX_UCDR_FO_GAIN 0x008
+#define QSERDES_V5_RX_UCDR_SO_GAIN 0x014
+#define QSERDES_V5_RX_UCDR_FASTLOCK_FO_GAIN 0x030
+#define QSERDES_V5_RX_UCDR_SO_SATURATION_AND_ENABLE 0x034
+#define QSERDES_V5_RX_UCDR_FASTLOCK_COUNT_LOW 0x03c
+#define QSERDES_V5_RX_UCDR_FASTLOCK_COUNT_HIGH 0x040
+#define QSERDES_V5_RX_UCDR_PI_CONTROLS 0x044
+#define QSERDES_V5_RX_UCDR_PI_CTRL2 0x048
+#define QSERDES_V5_RX_UCDR_SB2_THRESH1 0x04c
+#define QSERDES_V5_RX_UCDR_SB2_THRESH2 0x050
+#define QSERDES_V5_RX_UCDR_SB2_GAIN1 0x054
+#define QSERDES_V5_RX_UCDR_SB2_GAIN2 0x058
+#define QSERDES_V5_RX_AUX_DATA_TCOARSE_TFINE 0x060
+#define QSERDES_V5_RX_RCLK_AUXDATA_SEL 0x064
+#define QSERDES_V5_RX_AC_JTAG_ENABLE 0x068
+#define QSERDES_V5_RX_AC_JTAG_MODE 0x078
+#define QSERDES_V5_RX_RX_TERM_BW 0x080
+#define QSERDES_V5_RX_VGA_CAL_CNTRL1 0x0d4
+#define QSERDES_V5_RX_VGA_CAL_CNTRL2 0x0d8
+#define QSERDES_V5_RX_GM_CAL 0x0dc
+#define QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL1 0x0e8
+#define QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL2 0x0ec
+#define QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL3 0x0f0
+#define QSERDES_V5_RX_RX_EQU_ADAPTOR_CNTRL4 0x0f4
+#define QSERDES_V5_RX_RX_IDAC_TSETTLE_LOW 0x0f8
+#define QSERDES_V5_RX_RX_IDAC_TSETTLE_HIGH 0x0fc
+#define QSERDES_V5_RX_RX_IDAC_MEASURE_TIME 0x100
+#define QSERDES_V5_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x110
+#define QSERDES_V5_RX_RX_OFFSET_ADAPTOR_CNTRL2 0x114
+#define QSERDES_V5_RX_SIGDET_ENABLES 0x118
+#define QSERDES_V5_RX_SIGDET_CNTRL 0x11c
+#define QSERDES_V5_RX_SIGDET_LVL 0x120
+#define QSERDES_V5_RX_SIGDET_DEGLITCH_CNTRL 0x124
+#define QSERDES_V5_RX_RX_BAND 0x128
+#define QSERDES_V5_RX_RX_MODE_00_LOW 0x15c
+#define QSERDES_V5_RX_RX_MODE_00_HIGH 0x160
+#define QSERDES_V5_RX_RX_MODE_00_HIGH2 0x164
+#define QSERDES_V5_RX_RX_MODE_00_HIGH3 0x168
+#define QSERDES_V5_RX_RX_MODE_00_HIGH4 0x16c
+#define QSERDES_V5_RX_RX_MODE_01_LOW 0x170
+#define QSERDES_V5_RX_RX_MODE_01_HIGH 0x174
+#define QSERDES_V5_RX_RX_MODE_01_HIGH2 0x178
+#define QSERDES_V5_RX_RX_MODE_01_HIGH3 0x17c
+#define QSERDES_V5_RX_RX_MODE_01_HIGH4 0x180
+#define QSERDES_V5_RX_RX_MODE_10_LOW 0x184
+#define QSERDES_V5_RX_RX_MODE_10_HIGH 0x188
+#define QSERDES_V5_RX_RX_MODE_10_HIGH2 0x18c
+#define QSERDES_V5_RX_RX_MODE_10_HIGH3 0x190
+#define QSERDES_V5_RX_RX_MODE_10_HIGH4 0x194
+#define QSERDES_V5_RX_DFE_EN_TIMER 0x1a0
+#define QSERDES_V5_RX_DFE_CTLE_POST_CAL_OFFSET 0x1a4
+#define QSERDES_V5_RX_DCC_CTRL1 0x1a8
+#define QSERDES_V5_RX_VTH_CODE 0x1b0
+
+/* Only for QMP V5 PHY - UFS PCS registers */
+#define QPHY_V5_PCS_UFS_TIMER_20US_CORECLK_STEPS_MSB 0x00c
+#define QPHY_V5_PCS_UFS_TIMER_20US_CORECLK_STEPS_LSB 0x010
+#define QPHY_V5_PCS_UFS_PLL_CNTL 0x02c
+#define QPHY_V5_PCS_UFS_TX_LARGE_AMP_DRV_LVL 0x030
+#define QPHY_V5_PCS_UFS_TX_SMALL_AMP_DRV_LVL 0x038
+#define QPHY_V5_PCS_UFS_TX_HSGEAR_CAPABILITY 0x074
+#define QPHY_V5_PCS_UFS_RX_HSGEAR_CAPABILITY 0x0b4
+#define QPHY_V5_PCS_UFS_DEBUG_BUS_CLKSEL 0x124
+#define QPHY_V5_PCS_UFS_RX_MIN_HIBERN8_TIME 0x150
+#define QPHY_V5_PCS_UFS_RX_SIGDET_CTRL1 0x154
+#define QPHY_V5_PCS_UFS_RX_SIGDET_CTRL2 0x158
+#define QPHY_V5_PCS_UFS_TX_PWM_GEAR_BAND 0x160
+#define QPHY_V5_PCS_UFS_TX_HS_GEAR_BAND 0x168
+#define QPHY_V5_PCS_UFS_TX_MID_TERM_CTRL1 0x1d8
+#define QPHY_V5_PCS_UFS_MULTI_LANE_CTRL1 0x1e0
+
+/* Only for QMP V5 PHY - USB3 have different offsets than V4 */
+#define QPHY_V5_PCS_USB3_POWER_STATE_CONFIG1 0x300
+#define QPHY_V5_PCS_USB3_AUTONOMOUS_MODE_STATUS 0x304
+#define QPHY_V5_PCS_USB3_AUTONOMOUS_MODE_CTRL 0x308
+#define QPHY_V5_PCS_USB3_AUTONOMOUS_MODE_CTRL2 0x30c
+#define QPHY_V5_PCS_USB3_LFPS_RXTERM_IRQ_SOURCE_STATUS 0x310
+#define QPHY_V5_PCS_USB3_LFPS_RXTERM_IRQ_CLEAR 0x314
+#define QPHY_V5_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL 0x318
+#define QPHY_V5_PCS_USB3_LFPS_TX_ECSTART 0x31c
+#define QPHY_V5_PCS_USB3_LFPS_PER_TIMER_VAL 0x320
+#define QPHY_V5_PCS_USB3_LFPS_TX_END_CNT_U3_START 0x324
+#define QPHY_V5_PCS_USB3_LFPS_CONFIG1 0x328
+#define QPHY_V5_PCS_USB3_RXEQTRAINING_LOCK_TIME 0x32c
+#define QPHY_V5_PCS_USB3_RXEQTRAINING_WAIT_TIME 0x330
+#define QPHY_V5_PCS_USB3_RXEQTRAINING_CTLE_TIME 0x334
+#define QPHY_V5_PCS_USB3_RXEQTRAINING_WAIT_TIME_S2 0x338
+#define QPHY_V5_PCS_USB3_RXEQTRAINING_DFE_TIME_S2 0x33c
+#define QPHY_V5_PCS_USB3_RCVR_DTCT_DLY_U3_L 0x340
+#define QPHY_V5_PCS_USB3_RCVR_DTCT_DLY_U3_H 0x344
+#define QPHY_V5_PCS_USB3_ARCVR_DTCT_EN_PERIOD 0x348
+#define QPHY_V5_PCS_USB3_ARCVR_DTCT_CM_DLY 0x34c
+#define QPHY_V5_PCS_USB3_TXONESZEROS_RUN_LENGTH 0x350
+#define QPHY_V5_PCS_USB3_ALFPS_DEGLITCH_VAL 0x354
+#define QPHY_V5_PCS_USB3_SIGDET_STARTUP_TIMER_VAL 0x358
+#define QPHY_V5_PCS_USB3_TEST_CONTROL 0x35c
+#define QPHY_V5_PCS_USB3_RXTERMINATION_DLY_SEL 0x360
+
+/* Only for QMP V5 PHY - UNI has 0x1000 offset for PCS_USB3 regs */
+#define QPHY_V5_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL 0x1018
+#define QPHY_V5_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2 0x103c
+
#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
index 1097922..8f1bf7e 100644
--- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
+++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -22,6 +22,7 @@
#include <dt-bindings/phy/phy-qcom-qusb2.h>
+#define QUSB2PHY_PLL 0x0
#define QUSB2PHY_PLL_TEST 0x04
#define CLK_REF_SEL BIT(7)
@@ -135,6 +136,35 @@ enum qusb2phy_reg_layout {
QUSB2PHY_INTR_CTRL,
};
+static const struct qusb2_phy_init_tbl ipq6018_init_tbl[] = {
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL, 0x14),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xF8),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0xB3),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0x83),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0xC0),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x00),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TEST2, 0x14),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TEST, 0x80),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9F),
+};
+
+static const unsigned int ipq6018_regs_layout[] = {
+ [QUSB2PHY_PLL_STATUS] = 0x38,
+ [QUSB2PHY_PORT_TUNE1] = 0x80,
+ [QUSB2PHY_PORT_TUNE2] = 0x84,
+ [QUSB2PHY_PORT_TUNE3] = 0x88,
+ [QUSB2PHY_PORT_TUNE4] = 0x8C,
+ [QUSB2PHY_PORT_TUNE5] = 0x90,
+ [QUSB2PHY_PORT_TEST1] = 0x98,
+ [QUSB2PHY_PORT_TEST2] = 0x9C,
+ [QUSB2PHY_PORT_POWERDOWN] = 0xB4,
+ [QUSB2PHY_INTR_CTRL] = 0xBC,
+};
+
static const unsigned int msm8996_regs_layout[] = {
[QUSB2PHY_PLL_STATUS] = 0x38,
[QUSB2PHY_PORT_TUNE1] = 0x80,
@@ -245,6 +275,9 @@ struct qusb2_phy_cfg {
/* true if PHY has PLL_CORE_INPUT_OVERRIDE register to reset PLL */
bool has_pll_override;
+
+ /* true if PHY default clk scheme is single-ended */
+ bool se_clk_scheme_default;
};
static const struct qusb2_phy_cfg msm8996_phy_cfg = {
@@ -253,6 +286,7 @@ static const struct qusb2_phy_cfg msm8996_phy_cfg = {
.regs = msm8996_regs_layout,
.has_pll_test = true,
+ .se_clk_scheme_default = true,
.disable_ctrl = (CLAMP_N_EN | FREEZIO_N | POWER_DOWN),
.mask_core_ready = PLL_LOCKED,
.autoresume_en = BIT(3),
@@ -266,10 +300,22 @@ static const struct qusb2_phy_cfg msm8998_phy_cfg = {
.disable_ctrl = POWER_DOWN,
.mask_core_ready = CORE_READY_STATUS,
.has_pll_override = true,
+ .se_clk_scheme_default = true,
.autoresume_en = BIT(0),
.update_tune1_with_efuse = true,
};
+static const struct qusb2_phy_cfg ipq6018_phy_cfg = {
+ .tbl = ipq6018_init_tbl,
+ .tbl_num = ARRAY_SIZE(ipq6018_init_tbl),
+ .regs = ipq6018_regs_layout,
+
+ .disable_ctrl = POWER_DOWN,
+ .mask_core_ready = PLL_LOCKED,
+ /* autoresume not used */
+ .autoresume_en = BIT(0),
+};
+
static const struct qusb2_phy_cfg qusb2_v2_phy_cfg = {
.tbl = qusb2_v2_init_tbl,
.tbl_num = ARRAY_SIZE(qusb2_v2_init_tbl),
@@ -279,10 +325,23 @@ static const struct qusb2_phy_cfg qusb2_v2_phy_cfg = {
POWER_DOWN),
.mask_core_ready = CORE_READY_STATUS,
.has_pll_override = true,
+ .se_clk_scheme_default = true,
.autoresume_en = BIT(0),
.update_tune1_with_efuse = true,
};
+static const struct qusb2_phy_cfg sdm660_phy_cfg = {
+ .tbl = msm8996_init_tbl,
+ .tbl_num = ARRAY_SIZE(msm8996_init_tbl),
+ .regs = msm8996_regs_layout,
+
+ .has_pll_test = true,
+ .se_clk_scheme_default = false,
+ .disable_ctrl = (CLAMP_N_EN | FREEZIO_N | POWER_DOWN),
+ .mask_core_ready = PLL_LOCKED,
+ .autoresume_en = BIT(3),
+};
+
static const char * const qusb2_phy_vreg_names[] = {
"vdda-pll", "vdda-phy-dpdm",
};
@@ -701,8 +760,13 @@ static int qusb2_phy_init(struct phy *phy)
/* Required to get phy pll lock successfully */
usleep_range(150, 160);
- /* Default is single-ended clock on msm8996 */
- qphy->has_se_clk_scheme = true;
+ /*
+ * Not all the SoCs have got a readable TCSR_PHY_CLK_SCHEME
+ * register in the TCSR so, if there's none, use the default
+ * value hardcoded in the configuration.
+ */
+ qphy->has_se_clk_scheme = cfg->se_clk_scheme_default;
+
/*
* read TCSR_PHY_CLK_SCHEME register to check if single-ended
* clock scheme is selected. If yes, then disable differential
@@ -810,6 +874,9 @@ static const struct phy_ops qusb2_phy_gen_ops = {
static const struct of_device_id qusb2_phy_of_match_table[] = {
{
+ .compatible = "qcom,ipq6018-qusb2-phy",
+ .data = &ipq6018_phy_cfg,
+ }, {
.compatible = "qcom,ipq8074-qusb2-phy",
.data = &msm8996_phy_cfg,
}, {
@@ -819,6 +886,9 @@ static const struct of_device_id qusb2_phy_of_match_table[] = {
.compatible = "qcom,msm8998-qusb2-phy",
.data = &msm8998_phy_cfg,
}, {
+ .compatible = "qcom,sdm660-qusb2-phy",
+ .data = &sdm660_phy_cfg,
+ }, {
/*
* Deprecated. Only here to support legacy device
* trees that didn't include "qcom,qusb2-v2-phy"
diff --git a/drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c b/drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c
index a52a9bf..8807e59 100644
--- a/drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c
+++ b/drivers/phy/qualcomm/phy-qcom-usb-hs-28nm.c
@@ -401,13 +401,26 @@ static const struct hsphy_init_seq init_seq_femtophy[] = {
HSPHY_INIT_CFG(0x90, 0x60, 0),
};
+static const struct hsphy_init_seq init_seq_mdm9607[] = {
+ HSPHY_INIT_CFG(0x80, 0x44, 0),
+ HSPHY_INIT_CFG(0x81, 0x38, 0),
+ HSPHY_INIT_CFG(0x82, 0x24, 0),
+ HSPHY_INIT_CFG(0x83, 0x13, 0),
+};
+
static const struct hsphy_data hsphy_data_femtophy = {
.init_seq = init_seq_femtophy,
.init_seq_num = ARRAY_SIZE(init_seq_femtophy),
};
+static const struct hsphy_data hsphy_data_mdm9607 = {
+ .init_seq = init_seq_mdm9607,
+ .init_seq_num = ARRAY_SIZE(init_seq_mdm9607),
+};
+
static const struct of_device_id qcom_snps_hsphy_match[] = {
{ .compatible = "qcom,usb-hs-28nm-femtophy", .data = &hsphy_data_femtophy, },
+ { .compatible = "qcom,usb-hs-28nm-mdm9607", .data = &hsphy_data_mdm9607, },
{ },
};
MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_match);
diff --git a/drivers/phy/st/phy-stm32-usbphyc.c b/drivers/phy/st/phy-stm32-usbphyc.c
index a54317e..d08fbb1 100644
--- a/drivers/phy/st/phy-stm32-usbphyc.c
+++ b/drivers/phy/st/phy-stm32-usbphyc.c
@@ -8,7 +8,7 @@
#include <linux/bitfield.h>
#include <linux/clk.h>
#include <linux/delay.h>
-#include <linux/io.h>
+#include <linux/iopoll.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of_platform.h>
@@ -17,6 +17,7 @@
#define STM32_USBPHYC_PLL 0x0
#define STM32_USBPHYC_MISC 0x8
+#define STM32_USBPHYC_MONITOR(X) (0x108 + ((X) * 0x100))
#define STM32_USBPHYC_VERSION 0x3F4
/* STM32_USBPHYC_PLL bit fields */
@@ -32,19 +33,16 @@
/* STM32_USBPHYC_MISC bit fields */
#define SWITHOST BIT(0)
+/* STM32_USBPHYC_MONITOR bit fields */
+#define STM32_USBPHYC_MON_OUT GENMASK(3, 0)
+#define STM32_USBPHYC_MON_SEL GENMASK(8, 4)
+#define STM32_USBPHYC_MON_SEL_LOCKP 0x1F
+#define STM32_USBPHYC_MON_OUT_LOCKP BIT(3)
+
/* STM32_USBPHYC_VERSION bit fields */
#define MINREV GENMASK(3, 0)
#define MAJREV GENMASK(7, 4)
-static const char * const supplies_names[] = {
- "vdda1v1", /* 1V1 */
- "vdda1v8", /* 1V8 */
-};
-
-#define NUM_SUPPLIES ARRAY_SIZE(supplies_names)
-
-#define PLL_LOCK_TIME_US 100
-#define PLL_PWR_DOWN_TIME_US 5
#define PLL_FVCO_MHZ 2880
#define PLL_INFF_MIN_RATE_HZ 19200000
#define PLL_INFF_MAX_RATE_HZ 38400000
@@ -58,7 +56,6 @@ struct pll_params {
struct stm32_usbphyc_phy {
struct phy *phy;
struct stm32_usbphyc *usbphyc;
- struct regulator_bulk_data supplies[NUM_SUPPLIES];
u32 index;
bool active;
};
@@ -70,6 +67,9 @@ struct stm32_usbphyc {
struct reset_control *rst;
struct stm32_usbphyc_phy **phys;
int nphys;
+ struct regulator *vdda1v1;
+ struct regulator *vdda1v8;
+ atomic_t n_pll_cons;
int switch_setup;
};
@@ -83,6 +83,41 @@ static inline void stm32_usbphyc_clr_bits(void __iomem *reg, u32 bits)
writel_relaxed(readl_relaxed(reg) & ~bits, reg);
}
+static int stm32_usbphyc_regulators_enable(struct stm32_usbphyc *usbphyc)
+{
+ int ret;
+
+ ret = regulator_enable(usbphyc->vdda1v1);
+ if (ret)
+ return ret;
+
+ ret = regulator_enable(usbphyc->vdda1v8);
+ if (ret)
+ goto vdda1v1_disable;
+
+ return 0;
+
+vdda1v1_disable:
+ regulator_disable(usbphyc->vdda1v1);
+
+ return ret;
+}
+
+static int stm32_usbphyc_regulators_disable(struct stm32_usbphyc *usbphyc)
+{
+ int ret;
+
+ ret = regulator_disable(usbphyc->vdda1v8);
+ if (ret)
+ return ret;
+
+ ret = regulator_disable(usbphyc->vdda1v1);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
static void stm32_usbphyc_get_pll_params(u32 clk_rate,
struct pll_params *pll_params)
{
@@ -142,83 +177,106 @@ static int stm32_usbphyc_pll_init(struct stm32_usbphyc *usbphyc)
return 0;
}
-static bool stm32_usbphyc_has_one_phy_active(struct stm32_usbphyc *usbphyc)
+static int __stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc)
{
- int i;
+ void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL;
+ u32 pllen;
- for (i = 0; i < usbphyc->nphys; i++)
- if (usbphyc->phys[i]->active)
- return true;
+ stm32_usbphyc_clr_bits(pll_reg, PLLEN);
- return false;
+ /* Wait for minimum width of powerdown pulse (ENABLE = Low) */
+ if (readl_relaxed_poll_timeout(pll_reg, pllen, !(pllen & PLLEN), 5, 50))
+ dev_err(usbphyc->dev, "PLL not reset\n");
+
+ return stm32_usbphyc_regulators_disable(usbphyc);
+}
+
+static int stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc)
+{
+ /* Check if a phy port is still active or clk48 in use */
+ if (atomic_dec_return(&usbphyc->n_pll_cons) > 0)
+ return 0;
+
+ return __stm32_usbphyc_pll_disable(usbphyc);
}
static int stm32_usbphyc_pll_enable(struct stm32_usbphyc *usbphyc)
{
void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL;
- bool pllen = (readl_relaxed(pll_reg) & PLLEN);
+ bool pllen = readl_relaxed(pll_reg) & PLLEN;
int ret;
- /* Check if one phy port has already configured the pll */
- if (pllen && stm32_usbphyc_has_one_phy_active(usbphyc))
+ /*
+ * Check if a phy port or clk48 prepare has configured the pll
+ * and ensure the PLL is enabled
+ */
+ if (atomic_inc_return(&usbphyc->n_pll_cons) > 1 && pllen)
return 0;
if (pllen) {
- stm32_usbphyc_clr_bits(pll_reg, PLLEN);
- /* Wait for minimum width of powerdown pulse (ENABLE = Low) */
- udelay(PLL_PWR_DOWN_TIME_US);
+ /*
+ * PLL shouldn't be enabled without known consumer,
+ * disable it and reinit n_pll_cons
+ */
+ dev_warn(usbphyc->dev, "PLL enabled without known consumers\n");
+
+ ret = __stm32_usbphyc_pll_disable(usbphyc);
+ if (ret)
+ return ret;
}
+ ret = stm32_usbphyc_regulators_enable(usbphyc);
+ if (ret)
+ goto dec_n_pll_cons;
+
ret = stm32_usbphyc_pll_init(usbphyc);
if (ret)
- return ret;
+ goto reg_disable;
stm32_usbphyc_set_bits(pll_reg, PLLEN);
- /* Wait for maximum lock time */
- udelay(PLL_LOCK_TIME_US);
-
- if (!(readl_relaxed(pll_reg) & PLLEN)) {
- dev_err(usbphyc->dev, "PLLEN not set\n");
- return -EIO;
- }
-
return 0;
-}
-static int stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc)
-{
- void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL;
+reg_disable:
+ stm32_usbphyc_regulators_disable(usbphyc);
- /* Check if other phy port active */
- if (stm32_usbphyc_has_one_phy_active(usbphyc))
- return 0;
+dec_n_pll_cons:
+ atomic_dec(&usbphyc->n_pll_cons);
- stm32_usbphyc_clr_bits(pll_reg, PLLEN);
- /* Wait for minimum width of powerdown pulse (ENABLE = Low) */
- udelay(PLL_PWR_DOWN_TIME_US);
-
- if (readl_relaxed(pll_reg) & PLLEN) {
- dev_err(usbphyc->dev, "PLL not reset\n");
- return -EIO;
- }
-
- return 0;
+ return ret;
}
static int stm32_usbphyc_phy_init(struct phy *phy)
{
struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy);
struct stm32_usbphyc *usbphyc = usbphyc_phy->usbphyc;
+ u32 reg_mon = STM32_USBPHYC_MONITOR(usbphyc_phy->index);
+ u32 monsel = FIELD_PREP(STM32_USBPHYC_MON_SEL,
+ STM32_USBPHYC_MON_SEL_LOCKP);
+ u32 monout;
int ret;
ret = stm32_usbphyc_pll_enable(usbphyc);
if (ret)
return ret;
+ /* Check that PLL Lock input to PHY is High */
+ writel_relaxed(monsel, usbphyc->base + reg_mon);
+ ret = readl_relaxed_poll_timeout(usbphyc->base + reg_mon, monout,
+ (monout & STM32_USBPHYC_MON_OUT_LOCKP),
+ 100, 1000);
+ if (ret) {
+ dev_err(usbphyc->dev, "PLL Lock input to PHY is Low (val=%x)\n",
+ (u32)(monout & STM32_USBPHYC_MON_OUT));
+ goto pll_disable;
+ }
+
usbphyc_phy->active = true;
return 0;
+
+pll_disable:
+ return stm32_usbphyc_pll_disable(usbphyc);
}
static int stm32_usbphyc_phy_exit(struct phy *phy)
@@ -231,25 +289,9 @@ static int stm32_usbphyc_phy_exit(struct phy *phy)
return stm32_usbphyc_pll_disable(usbphyc);
}
-static int stm32_usbphyc_phy_power_on(struct phy *phy)
-{
- struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy);
-
- return regulator_bulk_enable(NUM_SUPPLIES, usbphyc_phy->supplies);
-}
-
-static int stm32_usbphyc_phy_power_off(struct phy *phy)
-{
- struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy);
-
- return regulator_bulk_disable(NUM_SUPPLIES, usbphyc_phy->supplies);
-}
-
static const struct phy_ops stm32_usbphyc_phy_ops = {
.init = stm32_usbphyc_phy_init,
.exit = stm32_usbphyc_phy_exit,
- .power_on = stm32_usbphyc_phy_power_on,
- .power_off = stm32_usbphyc_phy_power_off,
.owner = THIS_MODULE,
};
@@ -312,7 +354,7 @@ static int stm32_usbphyc_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct device_node *child, *np = dev->of_node;
struct phy_provider *phy_provider;
- u32 version;
+ u32 pllen, version;
int ret, port = 0;
usbphyc = devm_kzalloc(dev, sizeof(*usbphyc), GFP_KERNEL);
@@ -344,6 +386,19 @@ static int stm32_usbphyc_probe(struct platform_device *pdev)
ret = PTR_ERR(usbphyc->rst);
if (ret == -EPROBE_DEFER)
goto clk_disable;
+
+ stm32_usbphyc_clr_bits(usbphyc->base + STM32_USBPHYC_PLL, PLLEN);
+ }
+
+ /*
+ * Wait for minimum width of powerdown pulse (ENABLE = Low):
+ * we have to ensure the PLL is disabled before phys initialization.
+ */
+ if (readl_relaxed_poll_timeout(usbphyc->base + STM32_USBPHYC_PLL,
+ pllen, !(pllen & PLLEN), 5, 50)) {
+ dev_warn(usbphyc->dev, "PLL not reset\n");
+ ret = -EPROBE_DEFER;
+ goto clk_disable;
}
usbphyc->switch_setup = -EINVAL;
@@ -355,11 +410,26 @@ static int stm32_usbphyc_probe(struct platform_device *pdev)
goto clk_disable;
}
+ usbphyc->vdda1v1 = devm_regulator_get(dev, "vdda1v1");
+ if (IS_ERR(usbphyc->vdda1v1)) {
+ ret = PTR_ERR(usbphyc->vdda1v1);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "failed to get vdda1v1 supply: %d\n", ret);
+ goto clk_disable;
+ }
+
+ usbphyc->vdda1v8 = devm_regulator_get(dev, "vdda1v8");
+ if (IS_ERR(usbphyc->vdda1v8)) {
+ ret = PTR_ERR(usbphyc->vdda1v8);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "failed to get vdda1v8 supply: %d\n", ret);
+ goto clk_disable;
+ }
+
for_each_child_of_node(np, child) {
struct stm32_usbphyc_phy *usbphyc_phy;
struct phy *phy;
u32 index;
- int i;
phy = devm_phy_create(dev, child, &stm32_usbphyc_phy_ops);
if (IS_ERR(phy)) {
@@ -377,18 +447,6 @@ static int stm32_usbphyc_probe(struct platform_device *pdev)
goto put_child;
}
- for (i = 0; i < NUM_SUPPLIES; i++)
- usbphyc_phy->supplies[i].supply = supplies_names[i];
-
- ret = devm_regulator_bulk_get(&phy->dev, NUM_SUPPLIES,
- usbphyc_phy->supplies);
- if (ret) {
- if (ret != -EPROBE_DEFER)
- dev_err(&phy->dev,
- "failed to get regulators: %d\n", ret);
- goto put_child;
- }
-
ret = of_property_read_u32(child, "reg", &index);
if (ret || index > usbphyc->nphys) {
dev_err(&phy->dev, "invalid reg property: %d\n", ret);
@@ -432,6 +490,12 @@ static int stm32_usbphyc_probe(struct platform_device *pdev)
static int stm32_usbphyc_remove(struct platform_device *pdev)
{
struct stm32_usbphyc *usbphyc = dev_get_drvdata(&pdev->dev);
+ int port;
+
+ /* Ensure PHYs are not active, to allow PLL disabling */
+ for (port = 0; port < usbphyc->nphys; port++)
+ if (usbphyc->phys[port]->active)
+ stm32_usbphyc_phy_exit(usbphyc->phys[port]->phy);
clk_disable_unprepare(usbphyc->clk);
diff --git a/drivers/phy/xilinx/phy-zynqmp.c b/drivers/phy/xilinx/phy-zynqmp.c
index 2b0f921..2b65f84 100644
--- a/drivers/phy/xilinx/phy-zynqmp.c
+++ b/drivers/phy/xilinx/phy-zynqmp.c
@@ -874,13 +874,10 @@ static int xpsgtr_get_ref_clocks(struct xpsgtr_dev *gtr_dev)
snprintf(name, sizeof(name), "ref%u", refclk);
clk = devm_clk_get_optional(gtr_dev->dev, name);
- if (IS_ERR(clk)) {
- if (PTR_ERR(clk) != -EPROBE_DEFER)
- dev_err(gtr_dev->dev,
- "Failed to get reference clock %u: %ld\n",
- refclk, PTR_ERR(clk));
- return PTR_ERR(clk);
- }
+ if (IS_ERR(clk))
+ return dev_err_probe(gtr_dev->dev, PTR_ERR(clk),
+ "Failed to get reference clock %u\n",
+ refclk);
if (!clk)
continue;
