usb: dwc3: move generic dwc3 code from gadget into core
A few inits like the scale value or the removal of the DISSCRAMBLE is
done in the gadget code however it touches a general register.
Move this piece to the core.c file since it is likely to be requied by
both, parts of the core (device and host).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 2175475..6910a2d 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -349,6 +349,29 @@
dwc3_cache_hwparams(dwc);
+ reg = dwc3_readl(dwc->regs, DWC3_GCTL);
+ reg &= ~DWC3_GCTL_SCALEDOWN(3);
+ reg &= ~DWC3_GCTL_DISSCRAMBLE;
+
+ switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams0)) {
+ case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
+ reg &= ~DWC3_GCTL_DSBLCLKGTNG;
+ break;
+ default:
+ dev_dbg(dwc->dev, "No power optimization available\n");
+ }
+
+ /*
+ * WORKAROUND: DWC3 revisions <1.90a have a bug
+ * when The device fails to connect at SuperSpeed
+ * and falls back to high-speed mode which causes
+ * the device to enter in a Connect/Disconnect loop
+ */
+ if (dwc->revision < DWC3_REVISION_190A)
+ reg |= DWC3_GCTL_U2RSTECN;
+
+ dwc3_writel(dwc->regs, DWC3_GCTL, reg);
+
ret = dwc3_alloc_event_buffers(dwc, DWC3_EVENT_BUFFERS_SIZE);
if (ret) {
dev_err(dwc->dev, "failed to allocate event buffers\n");
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index fab4ee0..8aff490 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -1155,30 +1155,6 @@
dwc->gadget_driver = driver;
dwc->gadget.dev.driver = &driver->driver;
- reg = dwc3_readl(dwc->regs, DWC3_GCTL);
-
- reg &= ~DWC3_GCTL_SCALEDOWN(3);
- reg &= ~DWC3_GCTL_DISSCRAMBLE;
-
- switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams0)) {
- case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
- reg &= ~DWC3_GCTL_DSBLCLKGTNG;
- break;
- default:
- dev_dbg(dwc->dev, "No power optimization available\n");
- }
-
- /*
- * WORKAROUND: DWC3 revisions <1.90a have a bug
- * when The device fails to connect at SuperSpeed
- * and falls back to high-speed mode which causes
- * the device to enter in a Connect/Disconnect loop
- */
- if (dwc->revision < DWC3_REVISION_190A)
- reg |= DWC3_GCTL_U2RSTECN;
-
- dwc3_writel(dwc->regs, DWC3_GCTL, reg);
-
reg = dwc3_readl(dwc->regs, DWC3_DCFG);
reg &= ~(DWC3_DCFG_SPEED_MASK);
reg |= dwc->maximum_speed;
