diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
index 491c97b..878549b 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt
@@ -6,7 +6,7 @@
 	ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
 		  support on the platform.
 	ti,x-plate-resistance: X plate resistance
-	ti,coordiante-readouts: The sequencer supports a total of 16
+	ti,coordinate-readouts: The sequencer supports a total of 16
 				programmable steps each step is used to
 				read a single coordinate. A single
                                 readout is enough but multiple reads can
diff --git a/Documentation/input/gamepad.txt b/Documentation/input/gamepad.txt
index 8002c89..31bb6a4 100644
--- a/Documentation/input/gamepad.txt
+++ b/Documentation/input/gamepad.txt
@@ -122,12 +122,14 @@
       BTN_DPAD_*
     Analog buttons are reported as:
       ABS_HAT0X and ABS_HAT0Y
+      (for ABS values negative is left/up, positive is right/down)
 
 Analog-Sticks:
   The left analog-stick is reported as ABS_X, ABS_Y. The right analog stick is
   reported as ABS_RX, ABS_RY. Zero, one or two sticks may be present.
   If analog-sticks provide digital buttons, they are mapped accordingly as
   BTN_THUMBL (first/left) and BTN_THUMBR (second/right).
+    (for ABS values negative is left/up, positive is right/down)
 
 Triggers:
   Trigger buttons can be available as digital or analog buttons or both. User-
@@ -138,6 +140,7 @@
   ABS_HAT2X (right/ZR) and BTN_TL2 or ABS_HAT2Y (left/ZL).
   If only one trigger-button combination is present (upper+lower), they are
   reported as "right" triggers (BTN_TR/ABS_HAT1X).
+    (ABS trigger values start at 0, pressure is reported as positive values)
 
 Menu-Pad:
   Menu buttons are always digital and are mapped according to their location
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index 9874294..7e6c64e 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -630,7 +630,7 @@
 	tsc {
 		ti,wires = <4>;
 		ti,x-plate-resistance = <200>;
-		ti,coordiante-readouts = <5>;
+		ti,coordinate-readouts = <5>;
 		ti,wire-config = <0x00 0x11 0x22 0x33>;
 	};
 
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index 03febf8..4718ec4 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -485,3 +485,13 @@
 		tx-num-evt = <1>;
 		rx-num-evt = <1>;
 };
+
+&tscadc {
+	status = "okay";
+	tsc {
+		ti,wires = <4>;
+		ti,x-plate-resistance = <200>;
+		ti,coordinate-readouts = <5>;
+		ti,wire-config = <0x00 0x11 0x22 0x33>;
+	};
+};
diff --git a/drivers/input/Kconfig b/drivers/input/Kconfig
index 38b523a..a11ff74 100644
--- a/drivers/input/Kconfig
+++ b/drivers/input/Kconfig
@@ -80,7 +80,7 @@
 comment "Userland interfaces"
 
 config INPUT_MOUSEDEV
-	tristate "Mouse interface" if EXPERT
+	tristate "Mouse interface"
 	default y
 	help
 	  Say Y here if you want your mouse to be accessible as char devices
diff --git a/drivers/input/evdev.c b/drivers/input/evdev.c
index b6ded17..a06e125 100644
--- a/drivers/input/evdev.c
+++ b/drivers/input/evdev.c
@@ -18,6 +18,8 @@
 #include <linux/poll.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
+#include <linux/vmalloc.h>
+#include <linux/mm.h>
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/input/mt.h>
@@ -369,7 +371,11 @@
 	mutex_unlock(&evdev->mutex);
 
 	evdev_detach_client(evdev, client);
-	kfree(client);
+
+	if (is_vmalloc_addr(client))
+		vfree(client);
+	else
+		kfree(client);
 
 	evdev_close_device(evdev);
 
@@ -389,12 +395,14 @@
 {
 	struct evdev *evdev = container_of(inode->i_cdev, struct evdev, cdev);
 	unsigned int bufsize = evdev_compute_buffer_size(evdev->handle.dev);
+	unsigned int size = sizeof(struct evdev_client) +
+					bufsize * sizeof(struct input_event);
 	struct evdev_client *client;
 	int error;
 
-	client = kzalloc(sizeof(struct evdev_client) +
-				bufsize * sizeof(struct input_event),
-			 GFP_KERNEL);
+	client = kzalloc(size, GFP_KERNEL | __GFP_NOWARN);
+	if (!client)
+		client = vzalloc(size);
 	if (!client)
 		return -ENOMEM;
 
diff --git a/drivers/input/input.c b/drivers/input/input.c
index e75d015..846ccdd 100644
--- a/drivers/input/input.c
+++ b/drivers/input/input.c
@@ -2052,7 +2052,7 @@
 	if (dev->hint_events_per_packet < packet_size)
 		dev->hint_events_per_packet = packet_size;
 
-	dev->max_vals = max(dev->hint_events_per_packet, packet_size) + 2;
+	dev->max_vals = dev->hint_events_per_packet + 2;
 	dev->vals = kcalloc(dev->max_vals, sizeof(*dev->vals), GFP_KERNEL);
 	if (!dev->vals) {
 		error = -ENOMEM;
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index c1edd39..bb174c1 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -2,7 +2,7 @@
 # Input core configuration
 #
 menuconfig INPUT_KEYBOARD
-	bool "Keyboards" if EXPERT || !X86
+	bool "Keyboards"
 	default y
 	help
 	  Say Y here, and a list of supported keyboards will be displayed.
@@ -67,7 +67,7 @@
 	  module will be called atakbd.
 
 config KEYBOARD_ATKBD
-	tristate "AT keyboard" if EXPERT || !X86
+	tristate "AT keyboard"
 	default y
 	select SERIO
 	select SERIO_LIBPS2
@@ -525,7 +525,7 @@
 
 config KEYBOARD_SH_KEYSC
 	tristate "SuperH KEYSC keypad support"
-	depends on SUPERH || ARCH_SHMOBILE
+	depends on SUPERH || ARM || COMPILE_TEST
 	help
 	  Say Y here if you want to use a keypad attached to the KEYSC block
 	  on SuperH processors such as sh7722 and sh7343.
diff --git a/drivers/input/keyboard/gpio_keys.c b/drivers/input/keyboard/gpio_keys.c
index 440ce32..2db1324 100644
--- a/drivers/input/keyboard/gpio_keys.c
+++ b/drivers/input/keyboard/gpio_keys.c
@@ -26,6 +26,7 @@
 #include <linux/gpio_keys.h>
 #include <linux/workqueue.h>
 #include <linux/gpio.h>
+#include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/of_gpio.h>
 #include <linux/spinlock.h>
diff --git a/drivers/input/keyboard/gpio_keys_polled.c b/drivers/input/keyboard/gpio_keys_polled.c
index cd5ed9e..4e42819 100644
--- a/drivers/input/keyboard/gpio_keys_polled.c
+++ b/drivers/input/keyboard/gpio_keys_polled.c
@@ -25,6 +25,7 @@
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
 #include <linux/gpio_keys.h>
+#include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/of_gpio.h>
 
diff --git a/drivers/input/keyboard/lpc32xx-keys.c b/drivers/input/keyboard/lpc32xx-keys.c
index 4218143..8b1b013 100644
--- a/drivers/input/keyboard/lpc32xx-keys.c
+++ b/drivers/input/keyboard/lpc32xx-keys.c
@@ -383,7 +383,7 @@
 		.name	= DRV_NAME,
 		.owner	= THIS_MODULE,
 		.pm	= &lpc32xx_kscan_pm_ops,
-		.of_match_table = of_match_ptr(lpc32xx_kscan_match),
+		.of_match_table = lpc32xx_kscan_match,
 	}
 };
 
diff --git a/drivers/input/keyboard/nspire-keypad.c b/drivers/input/keyboard/nspire-keypad.c
index b3e3eda..b310649 100644
--- a/drivers/input/keyboard/nspire-keypad.c
+++ b/drivers/input/keyboard/nspire-keypad.c
@@ -143,8 +143,10 @@
 		return error;
 
 	error = nspire_keypad_chip_init(keypad);
-	if (error)
+	if (error) {
+		clk_disable_unprepare(keypad->clk);
 		return error;
+	}
 
 	return 0;
 }
@@ -267,7 +269,7 @@
 	.driver = {
 		.name = "nspire-keypad",
 		.owner = THIS_MODULE,
-		.of_match_table = of_match_ptr(nspire_keypad_dt_match),
+		.of_match_table = nspire_keypad_dt_match,
 	},
 	.probe = nspire_keypad_probe,
 };
diff --git a/drivers/input/keyboard/pxa27x_keypad.c b/drivers/input/keyboard/pxa27x_keypad.c
index a2e758d..186138c 100644
--- a/drivers/input/keyboard/pxa27x_keypad.c
+++ b/drivers/input/keyboard/pxa27x_keypad.c
@@ -27,6 +27,7 @@
 #include <linux/err.h>
 #include <linux/input/matrix_keypad.h>
 #include <linux/slab.h>
+#include <linux/of.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
diff --git a/drivers/input/keyboard/tegra-kbc.c b/drivers/input/keyboard/tegra-kbc.c
index 9cd20e6..8508879 100644
--- a/drivers/input/keyboard/tegra-kbc.c
+++ b/drivers/input/keyboard/tegra-kbc.c
@@ -614,7 +614,7 @@
 	unsigned int keymap_rows;
 	const struct of_device_id *match;
 
-	match = of_match_device(of_match_ptr(tegra_kbc_of_match), &pdev->dev);
+	match = of_match_device(tegra_kbc_of_match, &pdev->dev);
 
 	kbc = devm_kzalloc(&pdev->dev, sizeof(*kbc), GFP_KERNEL);
 	if (!kbc) {
diff --git a/drivers/input/keyboard/tnetv107x-keypad.c b/drivers/input/keyboard/tnetv107x-keypad.c
index 5f7b427..8bd24d5 100644
--- a/drivers/input/keyboard/tnetv107x-keypad.c
+++ b/drivers/input/keyboard/tnetv107x-keypad.c
@@ -60,8 +60,8 @@
 	struct clk			*clk;
 	struct device			*dev;
 	spinlock_t			lock;
-	u32				irq_press;
-	u32				irq_release;
+	int				irq_press;
+	int				irq_release;
 	int				rows, cols, row_shift;
 	int				debounce_ms, active_low;
 	u32				prev_keys[3];
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index aa51baa..5f4967d 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -156,7 +156,7 @@
 
 config INPUT_MAX8997_HAPTIC
 	tristate "MAXIM MAX8997 haptic controller support"
-	depends on HAVE_PWM && MFD_MAX8997
+	depends on PWM && HAVE_PWM && MFD_MAX8997
 	select INPUT_FF_MEMLESS
 	help
 	  This option enables device driver support for the haptic controller
@@ -461,7 +461,7 @@
 
 config INPUT_PWM_BEEPER
 	tristate "PWM beeper support"
-	depends on HAVE_PWM || PWM
+	depends on PWM && HAVE_PWM
 	help
 	  Say Y here to get support for PWM based beeper devices.
 
diff --git a/drivers/input/misc/ad714x-spi.c b/drivers/input/misc/ad714x-spi.c
index 6189148..3a90b710 100644
--- a/drivers/input/misc/ad714x-spi.c
+++ b/drivers/input/misc/ad714x-spi.c
@@ -108,7 +108,6 @@
 	struct ad714x_chip *chip = spi_get_drvdata(spi);
 
 	ad714x_remove(chip);
-	spi_set_drvdata(spi, NULL);
 
 	return 0;
 }
diff --git a/drivers/input/misc/cobalt_btns.c b/drivers/input/misc/cobalt_btns.c
index 4f77f87..b5d71d2 100644
--- a/drivers/input/misc/cobalt_btns.c
+++ b/drivers/input/misc/cobalt_btns.c
@@ -131,7 +131,6 @@
  err_free_mem:
 	input_free_polled_device(poll_dev);
 	kfree(bdev);
-	dev_set_drvdata(&pdev->dev, NULL);
 	return error;
 }
 
@@ -144,7 +143,6 @@
 	input_free_polled_device(bdev->poll_dev);
 	iounmap(bdev->reg);
 	kfree(bdev);
-	dev_set_drvdata(dev, NULL);
 
 	return 0;
 }
diff --git a/drivers/input/misc/mma8450.c b/drivers/input/misc/mma8450.c
index f330969..59d4dcd 100644
--- a/drivers/input/misc/mma8450.c
+++ b/drivers/input/misc/mma8450.c
@@ -168,7 +168,7 @@
  * I2C init/probing/exit functions
  */
 static int mma8450_probe(struct i2c_client *c,
-				   const struct i2c_device_id *id)
+			 const struct i2c_device_id *id)
 {
 	struct input_polled_dev *idev;
 	struct mma8450 *m;
@@ -204,6 +204,8 @@
 		goto err_free_mem;
 	}
 
+	i2c_set_clientdata(c, m);
+
 	return 0;
 
 err_free_mem:
diff --git a/drivers/input/misc/mpu3050.c b/drivers/input/misc/mpu3050.c
index dce0d95..6983ffb 100644
--- a/drivers/input/misc/mpu3050.c
+++ b/drivers/input/misc/mpu3050.c
@@ -383,6 +383,7 @@
 
 	pm_runtime_enable(&client->dev);
 	pm_runtime_set_autosuspend_delay(&client->dev, MPU3050_AUTO_DELAY);
+	i2c_set_clientdata(client, sensor);
 
 	return 0;
 
diff --git a/drivers/input/misc/pwm-beeper.c b/drivers/input/misc/pwm-beeper.c
index 2ff4d1c..940566e 100644
--- a/drivers/input/misc/pwm-beeper.c
+++ b/drivers/input/misc/pwm-beeper.c
@@ -16,6 +16,7 @@
 #include <linux/input.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pwm.h>
 #include <linux/slab.h>
diff --git a/drivers/input/misc/rb532_button.c b/drivers/input/misc/rb532_button.c
index fb4f8ac..83fff38 100644
--- a/drivers/input/misc/rb532_button.c
+++ b/drivers/input/misc/rb532_button.c
@@ -87,7 +87,6 @@
 
 	input_unregister_polled_device(poll_dev);
 	input_free_polled_device(poll_dev);
-	dev_set_drvdata(&pdev->dev, NULL);
 
 	return 0;
 }
diff --git a/drivers/input/misc/rotary_encoder.c b/drivers/input/misc/rotary_encoder.c
index 5b1aff8..f920ba7 100644
--- a/drivers/input/misc/rotary_encoder.c
+++ b/drivers/input/misc/rotary_encoder.c
@@ -24,6 +24,7 @@
 #include <linux/gpio.h>
 #include <linux/rotary_encoder.h>
 #include <linux/slab.h>
+#include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/of_gpio.h>
 
diff --git a/drivers/input/misc/sirfsoc-onkey.c b/drivers/input/misc/sirfsoc-onkey.c
index 0621c36..7b8b03e 100644
--- a/drivers/input/misc/sirfsoc-onkey.c
+++ b/drivers/input/misc/sirfsoc-onkey.c
@@ -153,7 +153,7 @@
 		.name	= "sirfsoc-pwrc",
 		.owner	= THIS_MODULE,
 		.pm	= &sirfsoc_pwrc_pm_ops,
-		.of_match_table = of_match_ptr(sirfsoc_pwrc_of_match),
+		.of_match_table = sirfsoc_pwrc_of_match,
 	}
 };
 
diff --git a/drivers/input/misc/uinput.c b/drivers/input/misc/uinput.c
index a0a4bba..7728359 100644
--- a/drivers/input/misc/uinput.c
+++ b/drivers/input/misc/uinput.c
@@ -430,20 +430,30 @@
 	return retval;
 }
 
-static ssize_t uinput_inject_event(struct uinput_device *udev,
-				   const char __user *buffer, size_t count)
+static ssize_t uinput_inject_events(struct uinput_device *udev,
+				    const char __user *buffer, size_t count)
 {
 	struct input_event ev;
+	size_t bytes = 0;
 
-	if (count < input_event_size())
+	if (count != 0 && count < input_event_size())
 		return -EINVAL;
 
-	if (input_event_from_user(buffer, &ev))
-		return -EFAULT;
+	while (bytes + input_event_size() <= count) {
+		/*
+		 * Note that even if some events were fetched successfully
+		 * we are still going to return EFAULT instead of partial
+		 * count to let userspace know that it got it's buffers
+		 * all wrong.
+		 */
+		if (input_event_from_user(buffer + bytes, &ev))
+			return -EFAULT;
 
-	input_event(udev->dev, ev.type, ev.code, ev.value);
+		input_event(udev->dev, ev.type, ev.code, ev.value);
+		bytes += input_event_size();
+	}
 
-	return input_event_size();
+	return bytes;
 }
 
 static ssize_t uinput_write(struct file *file, const char __user *buffer,
@@ -460,7 +470,7 @@
 		return retval;
 
 	retval = udev->state == UIST_CREATED ?
-			uinput_inject_event(udev, buffer, count) :
+			uinput_inject_events(udev, buffer, count) :
 			uinput_setup_device(udev, buffer, count);
 
 	mutex_unlock(&udev->mutex);
diff --git a/drivers/input/mouse/alps.c b/drivers/input/mouse/alps.c
index 8365847..ca7a26f 100644
--- a/drivers/input/mouse/alps.c
+++ b/drivers/input/mouse/alps.c
@@ -103,7 +103,6 @@
 	/* Dell Latitude E5500, E6400, E6500, Precision M4400 */
 	{ { 0x62, 0x02, 0x14 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf,
 		ALPS_PASS | ALPS_DUALPOINT | ALPS_PS2_INTERLEAVED },
-	{ { 0x73, 0x00, 0x14 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf, ALPS_DUALPOINT },		/* Dell XT2 */
 	{ { 0x73, 0x02, 0x50 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf, ALPS_FOUR_BUTTONS },		/* Dell Vostro 1400 */
 	{ { 0x52, 0x01, 0x14 }, 0x00, ALPS_PROTO_V2, 0xff, 0xff,
 		ALPS_PASS | ALPS_DUALPOINT | ALPS_PS2_INTERLEAVED },				/* Toshiba Tecra A11-11L */
@@ -1793,7 +1792,7 @@
 	snprintf(priv->phys, sizeof(priv->phys), "%s/input1", psmouse->ps2dev.serio->phys);
 	dev2->phys = priv->phys;
 	dev2->name = (priv->flags & ALPS_DUALPOINT) ?
-		     "DualPoint Stick" : "PS/2 Mouse";
+		     "DualPoint Stick" : "ALPS PS/2 Device";
 	dev2->id.bustype = BUS_I8042;
 	dev2->id.vendor  = 0x0002;
 	dev2->id.product = PSMOUSE_ALPS;
diff --git a/drivers/input/mouse/cypress_ps2.c b/drivers/input/mouse/cypress_ps2.c
index f51765f..a5869a8 100644
--- a/drivers/input/mouse/cypress_ps2.c
+++ b/drivers/input/mouse/cypress_ps2.c
@@ -439,7 +439,7 @@
 			case 2: return 5;
 			default:
 				/* Invalid contact (e.g. palm). Ignore it. */
-				return -1;
+				return 0;
 		}
 	}
 
@@ -452,17 +452,10 @@
 {
 	unsigned char *packet = psmouse->packet;
 	unsigned char header_byte = packet[0];
-	int contact_cnt;
 
 	memset(report_data, 0, sizeof(struct cytp_report_data));
 
-	contact_cnt = cypress_get_finger_count(header_byte);
-
-	if (contact_cnt < 0) /* e.g. palm detect */
-		return -EINVAL;
-
-	report_data->contact_cnt = contact_cnt;
-
+	report_data->contact_cnt = cypress_get_finger_count(header_byte);
 	report_data->tap = (header_byte & ABS_MULTIFINGER_TAP) ? 1 : 0;
 
 	if (report_data->contact_cnt == 1) {
@@ -535,11 +528,9 @@
 	int slots[CYTP_MAX_MT_SLOTS];
 	int n;
 
-	if (cypress_parse_packet(psmouse, cytp, &report_data))
-		return;
+	cypress_parse_packet(psmouse, cytp, &report_data);
 
 	n = report_data.contact_cnt;
-
 	if (n > CYTP_MAX_MT_SLOTS)
 		n = CYTP_MAX_MT_SLOTS;
 
@@ -605,10 +596,6 @@
 		return PSMOUSE_BAD_DATA;
 
 	contact_cnt = cypress_get_finger_count(packet[0]);
-
-	if (contact_cnt < 0)
-		return PSMOUSE_BAD_DATA;
-
 	if (cytp->mode & CYTP_BIT_ABS_NO_PRESSURE)
 		cypress_set_packet_size(psmouse, contact_cnt == 2 ? 7 : 4);
 	else
@@ -679,15 +666,15 @@
 {
 	struct cytp_data *cytp;
 
-	cytp = (struct cytp_data *)kzalloc(sizeof(struct cytp_data), GFP_KERNEL);
-	psmouse->private = (void *)cytp;
-	if (cytp == NULL)
+	cytp = kzalloc(sizeof(struct cytp_data), GFP_KERNEL);
+	if (!cytp)
 		return -ENOMEM;
 
-	cypress_reset(psmouse);
-
+	psmouse->private = cytp;
 	psmouse->pktsize = 8;
 
+	cypress_reset(psmouse);
+
 	if (cypress_query_hardware(psmouse)) {
 		psmouse_err(psmouse, "Unable to query Trackpad hardware.\n");
 		goto err_exit;
diff --git a/drivers/input/serio/Kconfig b/drivers/input/serio/Kconfig
index 1de1e5f..8541f94 100644
--- a/drivers/input/serio/Kconfig
+++ b/drivers/input/serio/Kconfig
@@ -2,7 +2,7 @@
 # Input core configuration
 #
 config SERIO
-	tristate "Serial I/O support" if EXPERT || !X86
+	tristate "Serial I/O support"
 	default y
 	help
 	  Say Yes here if you have any input device that uses serial I/O to
@@ -19,7 +19,7 @@
 if SERIO
 
 config SERIO_I8042
-	tristate "i8042 PC Keyboard controller" if EXPERT || !X86
+	tristate "i8042 PC Keyboard controller"
 	default y
 	depends on !PARISC && (!ARM || FOOTBRIDGE_HOST) && \
 		   (!SUPERH || SH_CAYMAN) && !M68K && !BLACKFIN && !S390 && \
@@ -170,7 +170,7 @@
 	  module will be called maceps2.
 
 config SERIO_LIBPS2
-	tristate "PS/2 driver library" if EXPERT
+	tristate "PS/2 driver library"
 	depends on SERIO_I8042 || SERIO_I8042=n
 	help
 	  Say Y here if you are using a driver for device connected
@@ -266,4 +266,14 @@
 	  To compile this driver as a module, choose M here: the module will
 	  be called olpc_apsp.
 
+config HYPERV_KEYBOARD
+	tristate "Microsoft Synthetic Keyboard driver"
+	depends on HYPERV
+	default HYPERV
+	help
+	  Select this option to enable the Hyper-V Keyboard driver.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called hyperv_keyboard.
+
 endif
diff --git a/drivers/input/serio/Makefile b/drivers/input/serio/Makefile
index 12298b1..815d874 100644
--- a/drivers/input/serio/Makefile
+++ b/drivers/input/serio/Makefile
@@ -28,3 +28,4 @@
 obj-$(CONFIG_SERIO_ARC_PS2)	+= arc_ps2.o
 obj-$(CONFIG_SERIO_APBPS2)	+= apbps2.o
 obj-$(CONFIG_SERIO_OLPC_APSP)	+= olpc_apsp.o
+obj-$(CONFIG_HYPERV_KEYBOARD)	+= hyperv-keyboard.o
diff --git a/drivers/input/serio/hyperv-keyboard.c b/drivers/input/serio/hyperv-keyboard.c
new file mode 100644
index 0000000..3a83c3c
--- /dev/null
+++ b/drivers/input/serio/hyperv-keyboard.c
@@ -0,0 +1,437 @@
+/*
+ *  Copyright (c) 2013, Microsoft Corporation.
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms and conditions of the GNU General Public License,
+ *  version 2, as published by the Free Software Foundation.
+ *
+ *  This program is distributed in the hope it will be useful, but WITHOUT
+ *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ *  more details.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/completion.h>
+#include <linux/hyperv.h>
+#include <linux/serio.h>
+#include <linux/slab.h>
+
+/*
+ * Current version 1.0
+ *
+ */
+#define SYNTH_KBD_VERSION_MAJOR 1
+#define SYNTH_KBD_VERSION_MINOR	0
+#define SYNTH_KBD_VERSION		(SYNTH_KBD_VERSION_MINOR | \
+					 (SYNTH_KBD_VERSION_MAJOR << 16))
+
+
+/*
+ * Message types in the synthetic input protocol
+ */
+enum synth_kbd_msg_type {
+	SYNTH_KBD_PROTOCOL_REQUEST = 1,
+	SYNTH_KBD_PROTOCOL_RESPONSE = 2,
+	SYNTH_KBD_EVENT = 3,
+	SYNTH_KBD_LED_INDICATORS = 4,
+};
+
+/*
+ * Basic message structures.
+ */
+struct synth_kbd_msg_hdr {
+	__le32 type;
+};
+
+struct synth_kbd_msg {
+	struct synth_kbd_msg_hdr header;
+	char data[]; /* Enclosed message */
+};
+
+union synth_kbd_version {
+	__le32 version;
+};
+
+/*
+ * Protocol messages
+ */
+struct synth_kbd_protocol_request {
+	struct synth_kbd_msg_hdr header;
+	union synth_kbd_version version_requested;
+};
+
+#define PROTOCOL_ACCEPTED	BIT(0)
+struct synth_kbd_protocol_response {
+	struct synth_kbd_msg_hdr header;
+	__le32 proto_status;
+};
+
+#define IS_UNICODE	BIT(0)
+#define IS_BREAK	BIT(1)
+#define IS_E0		BIT(2)
+#define IS_E1		BIT(3)
+struct synth_kbd_keystroke {
+	struct synth_kbd_msg_hdr header;
+	__le16 make_code;
+	__le16 reserved0;
+	__le32 info; /* Additional information */
+};
+
+
+#define HK_MAXIMUM_MESSAGE_SIZE 256
+
+#define KBD_VSC_SEND_RING_BUFFER_SIZE		(10 * PAGE_SIZE)
+#define KBD_VSC_RECV_RING_BUFFER_SIZE		(10 * PAGE_SIZE)
+
+#define XTKBD_EMUL0     0xe0
+#define XTKBD_EMUL1     0xe1
+#define XTKBD_RELEASE   0x80
+
+
+/*
+ * Represents a keyboard device
+ */
+struct hv_kbd_dev {
+	struct hv_device *hv_dev;
+	struct serio *hv_serio;
+	struct synth_kbd_protocol_request protocol_req;
+	struct synth_kbd_protocol_response protocol_resp;
+	/* Synchronize the request/response if needed */
+	struct completion wait_event;
+	spinlock_t lock; /* protects 'started' field */
+	bool started;
+};
+
+static void hv_kbd_on_receive(struct hv_device *hv_dev,
+			      struct synth_kbd_msg *msg, u32 msg_length)
+{
+	struct hv_kbd_dev *kbd_dev = hv_get_drvdata(hv_dev);
+	struct synth_kbd_keystroke *ks_msg;
+	unsigned long flags;
+	u32 msg_type = __le32_to_cpu(msg->header.type);
+	u32 info;
+	u16 scan_code;
+
+	switch (msg_type) {
+	case SYNTH_KBD_PROTOCOL_RESPONSE:
+		/*
+		 * Validate the information provided by the host.
+		 * If the host is giving us a bogus packet,
+		 * drop the packet (hoping the problem
+		 * goes away).
+		 */
+		if (msg_length < sizeof(struct synth_kbd_protocol_response)) {
+			dev_err(&hv_dev->device,
+				"Illegal protocol response packet (len: %d)\n",
+				msg_length);
+			break;
+		}
+
+		memcpy(&kbd_dev->protocol_resp, msg,
+			sizeof(struct synth_kbd_protocol_response));
+		complete(&kbd_dev->wait_event);
+		break;
+
+	case SYNTH_KBD_EVENT:
+		/*
+		 * Validate the information provided by the host.
+		 * If the host is giving us a bogus packet,
+		 * drop the packet (hoping the problem
+		 * goes away).
+		 */
+		if (msg_length < sizeof(struct  synth_kbd_keystroke)) {
+			dev_err(&hv_dev->device,
+				"Illegal keyboard event packet (len: %d)\n",
+				msg_length);
+			break;
+		}
+
+		ks_msg = (struct synth_kbd_keystroke *)msg;
+		info = __le32_to_cpu(ks_msg->info);
+
+		/*
+		 * Inject the information through the serio interrupt.
+		 */
+		spin_lock_irqsave(&kbd_dev->lock, flags);
+		if (kbd_dev->started) {
+			if (info & IS_E0)
+				serio_interrupt(kbd_dev->hv_serio,
+						XTKBD_EMUL0, 0);
+
+			scan_code = __le16_to_cpu(ks_msg->make_code);
+			if (info & IS_BREAK)
+				scan_code |= XTKBD_RELEASE;
+
+			serio_interrupt(kbd_dev->hv_serio, scan_code, 0);
+		}
+		spin_unlock_irqrestore(&kbd_dev->lock, flags);
+		break;
+
+	default:
+		dev_err(&hv_dev->device,
+			"unhandled message type %d\n", msg_type);
+	}
+}
+
+static void hv_kbd_handle_received_packet(struct hv_device *hv_dev,
+					  struct vmpacket_descriptor *desc,
+					  u32 bytes_recvd,
+					  u64 req_id)
+{
+	struct synth_kbd_msg *msg;
+	u32 msg_sz;
+
+	switch (desc->type) {
+	case VM_PKT_COMP:
+		break;
+
+	case VM_PKT_DATA_INBAND:
+		/*
+		 * We have a packet that has "inband" data. The API used
+		 * for retrieving the packet guarantees that the complete
+		 * packet is read. So, minimally, we should be able to
+		 * parse the payload header safely (assuming that the host
+		 * can be trusted.  Trusting the host seems to be a
+		 * reasonable assumption because in a virtualized
+		 * environment there is not whole lot you can do if you
+		 * don't trust the host.
+		 *
+		 * Nonetheless, let us validate if the host can be trusted
+		 * (in a trivial way).  The interesting aspect of this
+		 * validation is how do you recover if we discover that the
+		 * host is not to be trusted? Simply dropping the packet, I
+		 * don't think is an appropriate recovery.  In the interest
+		 * of failing fast, it may be better to crash the guest.
+		 * For now, I will just drop the packet!
+		 */
+
+		msg_sz = bytes_recvd - (desc->offset8 << 3);
+		if (msg_sz <= sizeof(struct synth_kbd_msg_hdr)) {
+			/*
+			 * Drop the packet and hope
+			 * the problem magically goes away.
+			 */
+			dev_err(&hv_dev->device,
+				"Illegal packet (type: %d, tid: %llx, size: %d)\n",
+				desc->type, req_id, msg_sz);
+			break;
+		}
+
+		msg = (void *)desc + (desc->offset8 << 3);
+		hv_kbd_on_receive(hv_dev, msg, msg_sz);
+		break;
+
+	default:
+		dev_err(&hv_dev->device,
+			"unhandled packet type %d, tid %llx len %d\n",
+			desc->type, req_id, bytes_recvd);
+		break;
+	}
+}
+
+static void hv_kbd_on_channel_callback(void *context)
+{
+	struct hv_device *hv_dev = context;
+	void *buffer;
+	int bufferlen = 0x100; /* Start with sensible size */
+	u32 bytes_recvd;
+	u64 req_id;
+	int error;
+
+	buffer = kmalloc(bufferlen, GFP_ATOMIC);
+	if (!buffer)
+		return;
+
+	while (1) {
+		error = vmbus_recvpacket_raw(hv_dev->channel, buffer, bufferlen,
+					     &bytes_recvd, &req_id);
+		switch (error) {
+		case 0:
+			if (bytes_recvd == 0) {
+				kfree(buffer);
+				return;
+			}
+
+			hv_kbd_handle_received_packet(hv_dev, buffer,
+						      bytes_recvd, req_id);
+			break;
+
+		case -ENOBUFS:
+			kfree(buffer);
+			/* Handle large packet */
+			bufferlen = bytes_recvd;
+			buffer = kmalloc(bytes_recvd, GFP_ATOMIC);
+			if (!buffer)
+				return;
+			break;
+		}
+	}
+}
+
+static int hv_kbd_connect_to_vsp(struct hv_device *hv_dev)
+{
+	struct hv_kbd_dev *kbd_dev = hv_get_drvdata(hv_dev);
+	struct synth_kbd_protocol_request *request;
+	struct synth_kbd_protocol_response *response;
+	u32 proto_status;
+	int error;
+
+	request = &kbd_dev->protocol_req;
+	memset(request, 0, sizeof(struct synth_kbd_protocol_request));
+	request->header.type = __cpu_to_le32(SYNTH_KBD_PROTOCOL_REQUEST);
+	request->version_requested.version = __cpu_to_le32(SYNTH_KBD_VERSION);
+
+	error = vmbus_sendpacket(hv_dev->channel, request,
+				 sizeof(struct synth_kbd_protocol_request),
+				 (unsigned long)request,
+				 VM_PKT_DATA_INBAND,
+				 VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED);
+	if (error)
+		return error;
+
+	if (!wait_for_completion_timeout(&kbd_dev->wait_event, 10 * HZ))
+		return -ETIMEDOUT;
+
+	response = &kbd_dev->protocol_resp;
+	proto_status = __le32_to_cpu(response->proto_status);
+	if (!(proto_status & PROTOCOL_ACCEPTED)) {
+		dev_err(&hv_dev->device,
+			"synth_kbd protocol request failed (version %d)\n",
+		        SYNTH_KBD_VERSION);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int hv_kbd_start(struct serio *serio)
+{
+	struct hv_kbd_dev *kbd_dev = serio->port_data;
+	unsigned long flags;
+
+	spin_lock_irqsave(&kbd_dev->lock, flags);
+	kbd_dev->started = true;
+	spin_unlock_irqrestore(&kbd_dev->lock, flags);
+
+	return 0;
+}
+
+static void hv_kbd_stop(struct serio *serio)
+{
+	struct hv_kbd_dev *kbd_dev = serio->port_data;
+	unsigned long flags;
+
+	spin_lock_irqsave(&kbd_dev->lock, flags);
+	kbd_dev->started = false;
+	spin_unlock_irqrestore(&kbd_dev->lock, flags);
+}
+
+static int hv_kbd_probe(struct hv_device *hv_dev,
+			const struct hv_vmbus_device_id *dev_id)
+{
+	struct hv_kbd_dev *kbd_dev;
+	struct serio *hv_serio;
+	int error;
+
+	kbd_dev = kzalloc(sizeof(struct hv_kbd_dev), GFP_KERNEL);
+	hv_serio = kzalloc(sizeof(struct serio), GFP_KERNEL);
+	if (!kbd_dev || !hv_serio) {
+		error = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	kbd_dev->hv_dev = hv_dev;
+	kbd_dev->hv_serio = hv_serio;
+	spin_lock_init(&kbd_dev->lock);
+	init_completion(&kbd_dev->wait_event);
+	hv_set_drvdata(hv_dev, kbd_dev);
+
+	hv_serio->dev.parent  = &hv_dev->device;
+	hv_serio->id.type = SERIO_8042_XL;
+	hv_serio->port_data = kbd_dev;
+	strlcpy(hv_serio->name, dev_name(&hv_dev->device),
+		sizeof(hv_serio->name));
+	strlcpy(hv_serio->phys, dev_name(&hv_dev->device),
+		sizeof(hv_serio->phys));
+
+	hv_serio->start = hv_kbd_start;
+	hv_serio->stop = hv_kbd_stop;
+
+	error = vmbus_open(hv_dev->channel,
+			   KBD_VSC_SEND_RING_BUFFER_SIZE,
+			   KBD_VSC_RECV_RING_BUFFER_SIZE,
+			   NULL, 0,
+			   hv_kbd_on_channel_callback,
+			   hv_dev);
+	if (error)
+		goto err_free_mem;
+
+	error = hv_kbd_connect_to_vsp(hv_dev);
+	if (error)
+		goto err_close_vmbus;
+
+	serio_register_port(kbd_dev->hv_serio);
+	return 0;
+
+err_close_vmbus:
+	vmbus_close(hv_dev->channel);
+err_free_mem:
+	kfree(hv_serio);
+	kfree(kbd_dev);
+	return error;
+}
+
+static int hv_kbd_remove(struct hv_device *hv_dev)
+{
+	struct hv_kbd_dev *kbd_dev = hv_get_drvdata(hv_dev);
+
+	serio_unregister_port(kbd_dev->hv_serio);
+	vmbus_close(hv_dev->channel);
+	kfree(kbd_dev);
+
+	hv_set_drvdata(hv_dev, NULL);
+
+	return 0;
+}
+
+/*
+ * Keyboard GUID
+ * {f912ad6d-2b17-48ea-bd65-f927a61c7684}
+ */
+#define HV_KBD_GUID \
+	.guid = { \
+			0x6d, 0xad, 0x12, 0xf9, 0x17, 0x2b, 0xea, 0x48, \
+			0xbd, 0x65, 0xf9, 0x27, 0xa6, 0x1c, 0x76, 0x84 \
+	}
+
+static const struct hv_vmbus_device_id id_table[] = {
+	/* Keyboard guid */
+	{ HV_KBD_GUID, },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(vmbus, id_table);
+
+static struct  hv_driver hv_kbd_drv = {
+	.name = KBUILD_MODNAME,
+	.id_table = id_table,
+	.probe = hv_kbd_probe,
+	.remove = hv_kbd_remove,
+};
+
+static int __init hv_kbd_init(void)
+{
+	return vmbus_driver_register(&hv_kbd_drv);
+}
+
+static void __exit hv_kbd_exit(void)
+{
+	vmbus_driver_unregister(&hv_kbd_drv);
+}
+
+MODULE_LICENSE("GPL");
+module_init(hv_kbd_init);
+module_exit(hv_kbd_exit);
diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h
index 5f306f7..0ec9abb 100644
--- a/drivers/input/serio/i8042-x86ia64io.h
+++ b/drivers/input/serio/i8042-x86ia64io.h
@@ -765,6 +765,7 @@
 	{ .id = "CPQA0D7", .driver_data = 0 },
 	{ .id = "", },
 };
+MODULE_DEVICE_TABLE(pnp, pnp_kbd_devids);
 
 static struct pnp_driver i8042_pnp_kbd_driver = {
 	.name           = "i8042 kbd",
@@ -786,6 +787,7 @@
 	{ .id = "SYN0801", .driver_data = 0 },
 	{ .id = "", },
 };
+MODULE_DEVICE_TABLE(pnp, pnp_aux_devids);
 
 static struct pnp_driver i8042_pnp_aux_driver = {
 	.name           = "i8042 aux",
diff --git a/drivers/input/tablet/wacom_sys.c b/drivers/input/tablet/wacom_sys.c
index e53416a..867e7c3 100644
--- a/drivers/input/tablet/wacom_sys.c
+++ b/drivers/input/tablet/wacom_sys.c
@@ -524,9 +524,6 @@
 
 		error = wacom_set_report(intf, WAC_HID_FEATURE_REPORT,
 		                         report_id, rep_data, length, 1);
-		if (error >= 0)
-			error = wacom_get_report(intf, WAC_HID_FEATURE_REPORT,
-			                         report_id, rep_data, length, 1);
 	} while ((error < 0 || rep_data[1] != mode) && limit++ < WAC_MSG_RETRIES);
 
 	kfree(rep_data);
@@ -548,7 +545,7 @@
 			/* MT Tablet PC touch */
 			return wacom_set_device_mode(intf, 3, 4, 4);
 		}
-		else if (features->type == WACOM_24HDT) {
+		else if (features->type == WACOM_24HDT || features->type == CINTIQ_HYBRID) {
 			return wacom_set_device_mode(intf, 18, 3, 2);
 		}
 	} else if (features->device_type == BTN_TOOL_PEN) {
@@ -719,7 +716,7 @@
 		return -ENOMEM;
 
 	if (wacom->wacom_wac.features.type >= INTUOS5S &&
-	    wacom->wacom_wac.features.type <= INTUOS5L)	{
+	    wacom->wacom_wac.features.type <= INTUOSPL) {
 		/*
 		 * Touch Ring and crop mark LED luminance may take on
 		 * one of four values:
@@ -981,14 +978,20 @@
 	case INTUOS5S:
 	case INTUOS5:
 	case INTUOS5L:
-		wacom->led.select[0] = 0;
-		wacom->led.select[1] = 0;
-		wacom->led.llv = 32;
-		wacom->led.hlv = 0;
-		wacom->led.img_lum = 0;
+	case INTUOSPS:
+	case INTUOSPM:
+	case INTUOSPL:
+		if (wacom->wacom_wac.features.device_type == BTN_TOOL_PEN) {
+			wacom->led.select[0] = 0;
+			wacom->led.select[1] = 0;
+			wacom->led.llv = 32;
+			wacom->led.hlv = 0;
+			wacom->led.img_lum = 0;
 
-		error = sysfs_create_group(&wacom->intf->dev.kobj,
-					   &intuos5_led_attr_group);
+			error = sysfs_create_group(&wacom->intf->dev.kobj,
+						  &intuos5_led_attr_group);
+		} else
+			return 0;
 		break;
 
 	default:
@@ -1024,8 +1027,12 @@
 	case INTUOS5S:
 	case INTUOS5:
 	case INTUOS5L:
-		sysfs_remove_group(&wacom->intf->dev.kobj,
-				   &intuos5_led_attr_group);
+	case INTUOSPS:
+	case INTUOSPM:
+	case INTUOSPL:
+		if (wacom->wacom_wac.features.device_type == BTN_TOOL_PEN)
+			sysfs_remove_group(&wacom->intf->dev.kobj,
+					   &intuos5_led_attr_group);
 		break;
 	}
 }
@@ -1185,34 +1192,47 @@
 		wacom_wac1->features =
 			*((struct wacom_features *)id->driver_info);
 		wacom_wac1->features.device_type = BTN_TOOL_PEN;
+		snprintf(wacom_wac1->name, WACOM_NAME_MAX, "%s (WL) Pen",
+			 wacom_wac1->features.name);
 		error = wacom_register_input(wacom1);
 		if (error)
-			goto fail1;
+			goto fail;
 
 		/* Touch interface */
-		wacom_wac2->features =
-			*((struct wacom_features *)id->driver_info);
-		wacom_wac2->features.pktlen = WACOM_PKGLEN_BBTOUCH3;
-		wacom_wac2->features.device_type = BTN_TOOL_FINGER;
-		wacom_wac2->features.x_max = wacom_wac2->features.y_max = 4096;
-		error = wacom_register_input(wacom2);
-		if (error)
-			goto fail2;
+		if (wacom_wac1->features.touch_max) {
+			wacom_wac2->features =
+				*((struct wacom_features *)id->driver_info);
+			wacom_wac2->features.pktlen = WACOM_PKGLEN_BBTOUCH3;
+			wacom_wac2->features.device_type = BTN_TOOL_FINGER;
+			wacom_wac2->features.x_max = wacom_wac2->features.y_max = 4096;
+			if (wacom_wac2->features.touch_max)
+				snprintf(wacom_wac2->name, WACOM_NAME_MAX,
+					 "%s (WL) Finger",wacom_wac2->features.name);
+			else
+				snprintf(wacom_wac2->name, WACOM_NAME_MAX,
+					 "%s (WL) Pad",wacom_wac2->features.name);
+			error = wacom_register_input(wacom2);
+			if (error)
+				goto fail;
+		}
 
 		error = wacom_initialize_battery(wacom);
 		if (error)
-			goto fail3;
+			goto fail;
 	}
 
 	return;
 
-fail3:
-	input_unregister_device(wacom_wac2->input);
-	wacom_wac2->input = NULL;
-fail2:
-	input_unregister_device(wacom_wac1->input);
-	wacom_wac1->input = NULL;
-fail1:
+fail:
+	if (wacom_wac2->input) {
+		input_unregister_device(wacom_wac2->input);
+		wacom_wac2->input = NULL;
+	}
+
+	if (wacom_wac1->input) {
+		input_unregister_device(wacom_wac1->input);
+		wacom_wac1->input = NULL;
+	}
 	return;
 }
 
@@ -1302,7 +1322,7 @@
 	 * HID descriptor. If this is the touch interface (wMaxPacketSize
 	 * of WACOM_PKGLEN_BBTOUCH3), override the table values.
 	 */
-	if (features->type >= INTUOS5S && features->type <= INTUOS5L) {
+	if (features->type >= INTUOS5S && features->type <= INTUOSPL) {
 		if (endpoint->wMaxPacketSize == WACOM_PKGLEN_BBTOUCH3) {
 			features->device_type = BTN_TOOL_FINGER;
 			features->pktlen = WACOM_PKGLEN_BBTOUCH3;
@@ -1329,10 +1349,12 @@
 		struct usb_device *other_dev;
 
 		/* Append the device type to the name */
-		strlcat(wacom_wac->name,
-			features->device_type == BTN_TOOL_PEN ?
-				" Pen" : " Finger",
-			sizeof(wacom_wac->name));
+		if (features->device_type != BTN_TOOL_FINGER)
+			strlcat(wacom_wac->name, " Pen", WACOM_NAME_MAX);
+		else if (features->touch_max)
+			strlcat(wacom_wac->name, " Finger", WACOM_NAME_MAX);
+		else
+			strlcat(wacom_wac->name, " Pad", WACOM_NAME_MAX);
 
 		other_dev = wacom_get_sibling(dev, features->oVid, features->oPid);
 		if (other_dev == NULL || wacom_get_usbdev_data(other_dev) == NULL)
diff --git a/drivers/input/tablet/wacom_wac.c b/drivers/input/tablet/wacom_wac.c
index c59b797..782c253 100644
--- a/drivers/input/tablet/wacom_wac.c
+++ b/drivers/input/tablet/wacom_wac.c
@@ -427,6 +427,13 @@
 			(features->type == WACOM_21UX2))
 		return 1;
 
+	/* Range Report */
+	if ((data[1] & 0xfe) == 0x20) {
+		input_report_key(input, BTN_TOUCH, 0);
+		input_report_abs(input, ABS_PRESSURE, 0);
+		input_report_abs(input, ABS_DISTANCE, wacom->features.distance_max);
+	}
+
 	/* Exit report */
 	if ((data[1] & 0xfe) == 0x80) {
 		if (features->quirks == WACOM_QUIRK_MULTI_INPUT)
@@ -477,7 +484,7 @@
 	/* general pen packet */
 	if ((data[1] & 0xb8) == 0xa0) {
 		t = (data[6] << 2) | ((data[7] >> 6) & 3);
-		if (features->type >= INTUOS4S && features->type <= WACOM_24HD) {
+		if (features->type >= INTUOS4S && features->type <= CINTIQ_HYBRID) {
 			t = (t << 1) | (data[1] & 1);
 		}
 		input_report_abs(input, ABS_PRESSURE, t);
@@ -621,14 +628,30 @@
 			} else {
 				input_report_abs(input, ABS_MISC, 0);
 			}
-		} else if (features->type >= INTUOS5S && features->type <= INTUOS5L) {
+		} else if (features->type == CINTIQ_HYBRID) {
+			/*
+			 * Do not send hardware buttons under Android. They
+			 * are already sent to the system through GPIO (and
+			 * have different meaning).
+			 */
+			input_report_key(input, BTN_1, (data[4] & 0x01));
+			input_report_key(input, BTN_2, (data[4] & 0x02));
+			input_report_key(input, BTN_3, (data[4] & 0x04));
+			input_report_key(input, BTN_4, (data[4] & 0x08));
+
+			input_report_key(input, BTN_5, (data[4] & 0x10));  /* Right  */
+			input_report_key(input, BTN_6, (data[4] & 0x20));  /* Up     */
+			input_report_key(input, BTN_7, (data[4] & 0x40));  /* Left   */
+			input_report_key(input, BTN_8, (data[4] & 0x80));  /* Down   */
+			input_report_key(input, BTN_0, (data[3] & 0x01));  /* Center */
+		} else if (features->type >= INTUOS5S && features->type <= INTUOSPL) {
 			int i;
 
 			/* Touch ring mode switch has no capacitive sensor */
 			input_report_key(input, BTN_0, (data[3] & 0x01));
 
 			/*
-			 * ExpressKeys on Intuos5 have a capacitive sensor in
+			 * ExpressKeys on Intuos5/Intuos Pro have a capacitive sensor in
 			 * addition to the mechanical switch. Switch data is
 			 * stored in data[4], capacitive data in data[5].
 			 */
@@ -716,7 +739,9 @@
 	     features->type == INTUOS4 ||
 	     features->type == INTUOS4S ||
 	     features->type == INTUOS5 ||
-	     features->type == INTUOS5S)) {
+	     features->type == INTUOS5S ||
+	     features->type == INTUOSPM ||
+	     features->type == INTUOSPS)) {
 
 		return 0;
 	}
@@ -769,8 +794,7 @@
 
 		} else if (wacom->tool[idx] == BTN_TOOL_MOUSE) {
 			/* I4 mouse */
-			if ((features->type >= INTUOS4S && features->type <= INTUOS4L) ||
-			    (features->type >= INTUOS5S && features->type <= INTUOS5L)) {
+			if (features->type >= INTUOS4S && features->type <= INTUOSPL) {
 				input_report_key(input, BTN_LEFT,   data[6] & 0x01);
 				input_report_key(input, BTN_MIDDLE, data[6] & 0x02);
 				input_report_key(input, BTN_RIGHT,  data[6] & 0x04);
@@ -797,7 +821,8 @@
 				}
 			}
 		} else if ((features->type < INTUOS3S || features->type == INTUOS3L ||
-				features->type == INTUOS4L || features->type == INTUOS5L) &&
+				features->type == INTUOS4L || features->type == INTUOS5L ||
+				features->type == INTUOSPL) &&
 			   wacom->tool[idx] == BTN_TOOL_LENS) {
 			/* Lens cursor packets */
 			input_report_key(input, BTN_LEFT,   data[8] & 0x01);
@@ -1107,6 +1132,7 @@
 
 static void wacom_bpt3_touch_msg(struct wacom_wac *wacom, unsigned char *data)
 {
+	struct wacom_features *features = &wacom->features;
 	struct input_dev *input = wacom->input;
 	bool touch = data[1] & 0x80;
 	int slot = input_mt_get_slot_by_key(input, data[0]);
@@ -1122,14 +1148,23 @@
 	if (touch) {
 		int x = (data[2] << 4) | (data[4] >> 4);
 		int y = (data[3] << 4) | (data[4] & 0x0f);
-		int a = data[5];
+		int width, height;
 
-		// "a" is a scaled-down area which we assume is roughly
-		// circular and which can be described as: a=(pi*r^2)/C.
-		int x_res  = input_abs_get_res(input, ABS_X);
-		int y_res  = input_abs_get_res(input, ABS_Y);
-		int width  = 2 * int_sqrt(a * WACOM_CONTACT_AREA_SCALE);
-		int height = width * y_res / x_res;
+		if (features->type >= INTUOSPS && features->type <= INTUOSPL) {
+			width  = data[5];
+			height = data[6];
+		} else {
+			/*
+			 * "a" is a scaled-down area which we assume is
+			 * roughly circular and which can be described as:
+			 * a=(pi*r^2)/C.
+			 */
+			int a = data[5];
+			int x_res  = input_abs_get_res(input, ABS_X);
+			int y_res  = input_abs_get_res(input, ABS_Y);
+			width  = 2 * int_sqrt(a * WACOM_CONTACT_AREA_SCALE);
+			height = width * y_res / x_res;
+		}
 
 		input_report_abs(input, ABS_MT_POSITION_X, x);
 		input_report_abs(input, ABS_MT_POSITION_Y, y);
@@ -1327,6 +1362,7 @@
 	case WACOM_22HD:
 	case WACOM_24HD:
 	case DTK:
+	case CINTIQ_HYBRID:
 		sync = wacom_intuos_irq(wacom_wac);
 		break;
 
@@ -1337,6 +1373,9 @@
 	case INTUOS5S:
 	case INTUOS5:
 	case INTUOS5L:
+	case INTUOSPS:
+	case INTUOSPM:
+	case INTUOSPL:
 		if (len == WACOM_PKGLEN_BBTOUCH3)
 			sync = wacom_bpt3_touch(wacom_wac);
 		else
@@ -1420,7 +1459,7 @@
 
 	/* these device have multiple inputs */
 	if (features->type >= WIRELESS ||
-	    (features->type >= INTUOS5S && features->type <= INTUOS5L) ||
+	    (features->type >= INTUOS5S && features->type <= INTUOSPL) ||
 	    (features->oVid && features->oPid))
 		features->quirks |= WACOM_QUIRK_MULTI_INPUT;
 
@@ -1627,6 +1666,8 @@
 
 	case INTUOS5:
 	case INTUOS5L:
+	case INTUOSPM:
+	case INTUOSPL:
 		if (features->device_type == BTN_TOOL_PEN) {
 			__set_bit(BTN_7, input_dev->keybit);
 			__set_bit(BTN_8, input_dev->keybit);
@@ -1634,6 +1675,7 @@
 		/* fall through */
 
 	case INTUOS5S:
+	case INTUOSPS:
 		__set_bit(INPUT_PROP_POINTER, input_dev->propbit);
 
 		if (features->device_type == BTN_TOOL_PEN) {
@@ -1765,6 +1807,24 @@
 					      0, 0);
 		}
 		break;
+
+	case CINTIQ_HYBRID:
+		__set_bit(BTN_1, input_dev->keybit);
+		__set_bit(BTN_2, input_dev->keybit);
+		__set_bit(BTN_3, input_dev->keybit);
+		__set_bit(BTN_4, input_dev->keybit);
+
+		__set_bit(BTN_5, input_dev->keybit);
+		__set_bit(BTN_6, input_dev->keybit);
+		__set_bit(BTN_7, input_dev->keybit);
+		__set_bit(BTN_8, input_dev->keybit);
+		__set_bit(BTN_0, input_dev->keybit);
+
+		input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
+		__set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
+
+		wacom_setup_cintiq(wacom_wac);
+		break;
 	}
 	return 0;
 }
@@ -1952,6 +2012,18 @@
 static const struct wacom_features wacom_features_0x2A =
 	{ "Wacom Intuos5 M", WACOM_PKGLEN_INTUOS,  44704, 27940, 2047,
 	  63, INTUOS5, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0x314 =
+	{ "Wacom Intuos Pro S", WACOM_PKGLEN_INTUOS,  31496, 19685, 2047,
+	  63, INTUOSPS, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+	  .touch_max = 16 };
+static const struct wacom_features wacom_features_0x315 =
+	{ "Wacom Intuos Pro M", WACOM_PKGLEN_INTUOS,  44704, 27940, 2047,
+	  63, INTUOSPM, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+	  .touch_max = 16 };
+static const struct wacom_features wacom_features_0x317 =
+	{ "Wacom Intuos Pro L", WACOM_PKGLEN_INTUOS,  65024, 40640, 2047,
+	  63, INTUOSPL, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+	  .touch_max = 16 };
 static const struct wacom_features wacom_features_0xF4 =
 	{ "Wacom Cintiq 24HD",       WACOM_PKGLEN_INTUOS,   104480, 65600, 2047,
 	  63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
@@ -2131,6 +2203,13 @@
 static const struct wacom_features wacom_features_0x6004 =
 	{ "ISD-V4",               WACOM_PKGLEN_GRAPHIRE,  12800,  8000,  255,
 	  0, TABLETPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
+static const struct wacom_features wacom_features_0x0307 =
+	{ "Wacom ISDv5 307", WACOM_PKGLEN_INTUOS,  59552,  33848, 2047,
+	  63, CINTIQ_HYBRID, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+	  .oVid = USB_VENDOR_ID_WACOM, .oPid = 0x309 };
+static const struct wacom_features wacom_features_0x0309 =
+	{ "Wacom ISDv5 309", .type = WACOM_24HDT, /* Touch */
+	  .oVid = USB_VENDOR_ID_WACOM, .oPid = 0x0307, .touch_max = 10 };
 
 #define USB_DEVICE_WACOM(prod)					\
 	USB_DEVICE(USB_VENDOR_ID_WACOM, prod),			\
@@ -2259,12 +2338,17 @@
 	{ USB_DEVICE_WACOM(0x300) },
 	{ USB_DEVICE_WACOM(0x301) },
 	{ USB_DEVICE_WACOM(0x304) },
+	{ USB_DEVICE_DETAILED(0x314, USB_CLASS_HID, 0, 0) },
+	{ USB_DEVICE_DETAILED(0x315, USB_CLASS_HID, 0, 0) },
+	{ USB_DEVICE_DETAILED(0x317, USB_CLASS_HID, 0, 0) },
 	{ USB_DEVICE_WACOM(0x4001) },
 	{ USB_DEVICE_WACOM(0x47) },
 	{ USB_DEVICE_WACOM(0xF4) },
 	{ USB_DEVICE_WACOM(0xF8) },
 	{ USB_DEVICE_DETAILED(0xF6, USB_CLASS_HID, 0, 0) },
 	{ USB_DEVICE_WACOM(0xFA) },
+	{ USB_DEVICE_WACOM(0x0307) },
+	{ USB_DEVICE_DETAILED(0x0309, USB_CLASS_HID, 0, 0) },
 	{ USB_DEVICE_LENOVO(0x6004) },
 	{ }
 };
diff --git a/drivers/input/tablet/wacom_wac.h b/drivers/input/tablet/wacom_wac.h
index dfc9e08..fd23a37 100644
--- a/drivers/input/tablet/wacom_wac.h
+++ b/drivers/input/tablet/wacom_wac.h
@@ -14,6 +14,8 @@
 /* maximum packet length for USB devices */
 #define WACOM_PKGLEN_MAX	64
 
+#define WACOM_NAME_MAX		64
+
 /* packet length for individual models */
 #define WACOM_PKGLEN_PENPRTN	 7
 #define WACOM_PKGLEN_GRAPHIRE	 8
@@ -76,10 +78,14 @@
 	INTUOS5S,
 	INTUOS5,
 	INTUOS5L,
+	INTUOSPS,
+	INTUOSPM,
+	INTUOSPL,
 	WACOM_21UX2,
 	WACOM_22HD,
 	DTK,
 	WACOM_24HD,
+	CINTIQ_HYBRID,
 	CINTIQ,
 	WACOM_BEE,
 	WACOM_13HD,
@@ -126,7 +132,7 @@
 };
 
 struct wacom_wac {
-	char name[64];
+	char name[WACOM_NAME_MAX];
 	unsigned char *data;
 	int tool[2];
 	int id[2];
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index e09ec67..00d1e54 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -919,4 +919,17 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called tps6507x_ts.
 
+config TOUCHSCREEN_ZFORCE
+	tristate "Neonode zForce infrared touchscreens"
+	depends on I2C
+	depends on GPIOLIB
+	help
+	  Say Y here if you have a touchscreen using the zforce
+	  infraread technology from Neonode.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called zforce_ts.
+
 endif
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index f5216c1..7587883 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -75,3 +75,4 @@
 obj-$(CONFIG_TOUCHSCREEN_WM97XX_ZYLONITE)	+= zylonite-wm97xx.o
 obj-$(CONFIG_TOUCHSCREEN_W90X900)	+= w90p910_ts.o
 obj-$(CONFIG_TOUCHSCREEN_TPS6507X)	+= tps6507x-ts.o
+obj-$(CONFIG_TOUCHSCREEN_ZFORCE)	+= zforce_ts.o
diff --git a/drivers/input/touchscreen/ad7877.c b/drivers/input/touchscreen/ad7877.c
index f3a174a..69834dd 100644
--- a/drivers/input/touchscreen/ad7877.c
+++ b/drivers/input/touchscreen/ad7877.c
@@ -806,7 +806,6 @@
 err_free_mem:
 	input_free_device(input_dev);
 	kfree(ts);
-	spi_set_drvdata(spi, NULL);
 	return err;
 }
 
@@ -823,7 +822,6 @@
 	kfree(ts);
 
 	dev_dbg(&spi->dev, "unregistered touchscreen\n");
-	spi_set_drvdata(spi, NULL);
 
 	return 0;
 }
diff --git a/drivers/input/touchscreen/ad7879-spi.c b/drivers/input/touchscreen/ad7879-spi.c
index 606da5b..1a7b114 100644
--- a/drivers/input/touchscreen/ad7879-spi.c
+++ b/drivers/input/touchscreen/ad7879-spi.c
@@ -142,7 +142,6 @@
 	struct ad7879 *ts = spi_get_drvdata(spi);
 
 	ad7879_remove(ts);
-	spi_set_drvdata(spi, NULL);
 
 	return 0;
 }
diff --git a/drivers/input/touchscreen/cyttsp4_core.c b/drivers/input/touchscreen/cyttsp4_core.c
index d038575..42d830e 100644
--- a/drivers/input/touchscreen/cyttsp4_core.c
+++ b/drivers/input/touchscreen/cyttsp4_core.c
@@ -2113,7 +2113,6 @@
 error_request_irq:
 	if (cd->cpdata->init)
 		cd->cpdata->init(cd->cpdata, 0, dev);
-	dev_set_drvdata(dev, NULL);
 error_free_xfer:
 	kfree(cd->xfer_buf);
 error_free_cd:
@@ -2151,7 +2150,6 @@
 	free_irq(cd->irq, cd);
 	if (cd->cpdata->init)
 		cd->cpdata->init(cd->cpdata, 0, dev);
-	dev_set_drvdata(dev, NULL);
 	cyttsp4_free_si_ptrs(cd);
 	kfree(cd);
 	return 0;
diff --git a/drivers/input/touchscreen/cyttsp4_spi.c b/drivers/input/touchscreen/cyttsp4_spi.c
index a71e114..b19434c 100644
--- a/drivers/input/touchscreen/cyttsp4_spi.c
+++ b/drivers/input/touchscreen/cyttsp4_spi.c
@@ -171,10 +171,7 @@
 	ts = cyttsp4_probe(&cyttsp_spi_bus_ops, &spi->dev, spi->irq,
 			  CY_SPI_DATA_BUF_SIZE);
 
-	if (IS_ERR(ts))
-		return PTR_ERR(ts);
-
-	return 0;
+	return PTR_ERR_OR_ZERO(ts);
 }
 
 static int cyttsp4_spi_remove(struct spi_device *spi)
diff --git a/drivers/input/touchscreen/egalax_ts.c b/drivers/input/touchscreen/egalax_ts.c
index ef5fcb0..054d225 100644
--- a/drivers/input/touchscreen/egalax_ts.c
+++ b/drivers/input/touchscreen/egalax_ts.c
@@ -273,7 +273,7 @@
 		.name	= "egalax_ts",
 		.owner	= THIS_MODULE,
 		.pm	= &egalax_ts_pm_ops,
-		.of_match_table	= of_match_ptr(egalax_ts_dt_ids),
+		.of_match_table	= egalax_ts_dt_ids,
 	},
 	.id_table	= egalax_ts_id,
 	.probe		= egalax_ts_probe,
diff --git a/drivers/input/touchscreen/htcpen.c b/drivers/input/touchscreen/htcpen.c
index 6650085..92e2243 100644
--- a/drivers/input/touchscreen/htcpen.c
+++ b/drivers/input/touchscreen/htcpen.c
@@ -186,8 +186,6 @@
 	release_region(HTCPEN_PORT_INIT, 1);
 	release_region(HTCPEN_PORT_IRQ_CLEAR, 1);
 
-	dev_set_drvdata(dev, NULL);
-
 	return 0;
 }
 
diff --git a/drivers/input/touchscreen/st1232.c b/drivers/input/touchscreen/st1232.c
index 1740a24..2f03b2f 100644
--- a/drivers/input/touchscreen/st1232.c
+++ b/drivers/input/touchscreen/st1232.c
@@ -24,6 +24,7 @@
 #include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/of_gpio.h>
 #include <linux/pm_qos.h>
 #include <linux/slab.h>
diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index 24e625c..68beada 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -354,9 +354,16 @@
 	if (err < 0)
 		return err;
 
-	err = of_property_read_u32(node, "ti,coordiante-readouts",
+	/*
+	 * Try with the new binding first. If it fails, try again with
+	 * bogus, miss-spelled version.
+	 */
+	err = of_property_read_u32(node, "ti,coordinate-readouts",
 			&ts_dev->coordinate_readouts);
 	if (err < 0)
+		err = of_property_read_u32(node, "ti,coordiante-readouts",
+				&ts_dev->coordinate_readouts);
+	if (err < 0)
 		return err;
 
 	return of_property_read_u32_array(node, "ti,wire-config",
@@ -511,7 +518,7 @@
 		.name   = "TI-am335x-tsc",
 		.owner	= THIS_MODULE,
 		.pm	= TITSC_PM_OPS,
-		.of_match_table = of_match_ptr(ti_tsc_dt_ids),
+		.of_match_table = ti_tsc_dt_ids,
 	},
 };
 module_platform_driver(ti_tsc_driver);
diff --git a/drivers/input/touchscreen/tsc2005.c b/drivers/input/touchscreen/tsc2005.c
index 7213e8b..8113533 100644
--- a/drivers/input/touchscreen/tsc2005.c
+++ b/drivers/input/touchscreen/tsc2005.c
@@ -678,7 +678,6 @@
 err_remove_sysfs:
 	sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
 err_clear_drvdata:
-	spi_set_drvdata(spi, NULL);
 	free_irq(spi->irq, ts);
 err_free_mem:
 	input_free_device(input_dev);
@@ -696,7 +695,6 @@
 	input_unregister_device(ts->idev);
 	kfree(ts);
 
-	spi_set_drvdata(spi, NULL);
 	return 0;
 }
 
diff --git a/drivers/input/touchscreen/zforce_ts.c b/drivers/input/touchscreen/zforce_ts.c
new file mode 100644
index 0000000..75762d6
--- /dev/null
+++ b/drivers/input/touchscreen/zforce_ts.c
@@ -0,0 +1,836 @@
+/*
+ * Copyright (C) 2012-2013 MundoReader S.L.
+ * Author: Heiko Stuebner <heiko@sntech.de>
+ *
+ * based in parts on Nook zforce driver
+ *
+ * Copyright (C) 2010 Barnes & Noble, Inc.
+ * Author: Pieter Truter<ptruter@intrinsyc.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/hrtimer.h>
+#include <linux/slab.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/device.h>
+#include <linux/sysfs.h>
+#include <linux/input/mt.h>
+#include <linux/platform_data/zforce_ts.h>
+
+#define WAIT_TIMEOUT		msecs_to_jiffies(1000)
+
+#define FRAME_START		0xee
+
+/* Offsets of the different parts of the payload the controller sends */
+#define PAYLOAD_HEADER		0
+#define PAYLOAD_LENGTH		1
+#define PAYLOAD_BODY		2
+
+/* Response offsets */
+#define RESPONSE_ID		0
+#define RESPONSE_DATA		1
+
+/* Commands */
+#define COMMAND_DEACTIVATE	0x00
+#define COMMAND_INITIALIZE	0x01
+#define COMMAND_RESOLUTION	0x02
+#define COMMAND_SETCONFIG	0x03
+#define COMMAND_DATAREQUEST	0x04
+#define COMMAND_SCANFREQ	0x08
+#define COMMAND_STATUS		0X1e
+
+/*
+ * Responses the controller sends as a result of
+ * command requests
+ */
+#define RESPONSE_DEACTIVATE	0x00
+#define RESPONSE_INITIALIZE	0x01
+#define RESPONSE_RESOLUTION	0x02
+#define RESPONSE_SETCONFIG	0x03
+#define RESPONSE_SCANFREQ	0x08
+#define RESPONSE_STATUS		0X1e
+
+/*
+ * Notifications are send by the touch controller without
+ * being requested by the driver and include for example
+ * touch indications
+ */
+#define NOTIFICATION_TOUCH		0x04
+#define NOTIFICATION_BOOTCOMPLETE	0x07
+#define NOTIFICATION_OVERRUN		0x25
+#define NOTIFICATION_PROXIMITY		0x26
+#define NOTIFICATION_INVALID_COMMAND	0xfe
+
+#define ZFORCE_REPORT_POINTS		2
+#define ZFORCE_MAX_AREA			0xff
+
+#define STATE_DOWN			0
+#define STATE_MOVE			1
+#define STATE_UP			2
+
+#define SETCONFIG_DUALTOUCH		(1 << 0)
+
+struct zforce_point {
+	int coord_x;
+	int coord_y;
+	int state;
+	int id;
+	int area_major;
+	int area_minor;
+	int orientation;
+	int pressure;
+	int prblty;
+};
+
+/*
+ * @client		the i2c_client
+ * @input		the input device
+ * @suspending		in the process of going to suspend (don't emit wakeup
+ *			events for commands executed to suspend the device)
+ * @suspended		device suspended
+ * @access_mutex	serialize i2c-access, to keep multipart reads together
+ * @command_done	completion to wait for the command result
+ * @command_mutex	serialize commands send to the ic
+ * @command_waiting	the id of the command that that is currently waiting
+ *			for a result
+ * @command_result	returned result of the command
+ */
+struct zforce_ts {
+	struct i2c_client	*client;
+	struct input_dev	*input;
+	const struct zforce_ts_platdata *pdata;
+	char			phys[32];
+
+	bool			suspending;
+	bool			suspended;
+	bool			boot_complete;
+
+	/* Firmware version information */
+	u16			version_major;
+	u16			version_minor;
+	u16			version_build;
+	u16			version_rev;
+
+	struct mutex		access_mutex;
+
+	struct completion	command_done;
+	struct mutex		command_mutex;
+	int			command_waiting;
+	int			command_result;
+};
+
+static int zforce_command(struct zforce_ts *ts, u8 cmd)
+{
+	struct i2c_client *client = ts->client;
+	char buf[3];
+	int ret;
+
+	dev_dbg(&client->dev, "%s: 0x%x\n", __func__, cmd);
+
+	buf[0] = FRAME_START;
+	buf[1] = 1; /* data size, command only */
+	buf[2] = cmd;
+
+	mutex_lock(&ts->access_mutex);
+	ret = i2c_master_send(client, &buf[0], ARRAY_SIZE(buf));
+	mutex_unlock(&ts->access_mutex);
+	if (ret < 0) {
+		dev_err(&client->dev, "i2c send data request error: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int zforce_send_wait(struct zforce_ts *ts, const char *buf, int len)
+{
+	struct i2c_client *client = ts->client;
+	int ret;
+
+	ret = mutex_trylock(&ts->command_mutex);
+	if (!ret) {
+		dev_err(&client->dev, "already waiting for a command\n");
+		return -EBUSY;
+	}
+
+	dev_dbg(&client->dev, "sending %d bytes for command 0x%x\n",
+		buf[1], buf[2]);
+
+	ts->command_waiting = buf[2];
+
+	mutex_lock(&ts->access_mutex);
+	ret = i2c_master_send(client, buf, len);
+	mutex_unlock(&ts->access_mutex);
+	if (ret < 0) {
+		dev_err(&client->dev, "i2c send data request error: %d\n", ret);
+		goto unlock;
+	}
+
+	dev_dbg(&client->dev, "waiting for result for command 0x%x\n", buf[2]);
+
+	if (wait_for_completion_timeout(&ts->command_done, WAIT_TIMEOUT) == 0) {
+		ret = -ETIME;
+		goto unlock;
+	}
+
+	ret = ts->command_result;
+
+unlock:
+	mutex_unlock(&ts->command_mutex);
+	return ret;
+}
+
+static int zforce_command_wait(struct zforce_ts *ts, u8 cmd)
+{
+	struct i2c_client *client = ts->client;
+	char buf[3];
+	int ret;
+
+	dev_dbg(&client->dev, "%s: 0x%x\n", __func__, cmd);
+
+	buf[0] = FRAME_START;
+	buf[1] = 1; /* data size, command only */
+	buf[2] = cmd;
+
+	ret = zforce_send_wait(ts, &buf[0], ARRAY_SIZE(buf));
+	if (ret < 0) {
+		dev_err(&client->dev, "i2c send data request error: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int zforce_resolution(struct zforce_ts *ts, u16 x, u16 y)
+{
+	struct i2c_client *client = ts->client;
+	char buf[7] = { FRAME_START, 5, COMMAND_RESOLUTION,
+			(x & 0xff), ((x >> 8) & 0xff),
+			(y & 0xff), ((y >> 8) & 0xff) };
+
+	dev_dbg(&client->dev, "set resolution to (%d,%d)\n", x, y);
+
+	return zforce_send_wait(ts, &buf[0], ARRAY_SIZE(buf));
+}
+
+static int zforce_scan_frequency(struct zforce_ts *ts, u16 idle, u16 finger,
+				 u16 stylus)
+{
+	struct i2c_client *client = ts->client;
+	char buf[9] = { FRAME_START, 7, COMMAND_SCANFREQ,
+			(idle & 0xff), ((idle >> 8) & 0xff),
+			(finger & 0xff), ((finger >> 8) & 0xff),
+			(stylus & 0xff), ((stylus >> 8) & 0xff) };
+
+	dev_dbg(&client->dev, "set scan frequency to (idle: %d, finger: %d, stylus: %d)\n",
+		idle, finger, stylus);
+
+	return zforce_send_wait(ts, &buf[0], ARRAY_SIZE(buf));
+}
+
+static int zforce_setconfig(struct zforce_ts *ts, char b1)
+{
+	struct i2c_client *client = ts->client;
+	char buf[7] = { FRAME_START, 5, COMMAND_SETCONFIG,
+			b1, 0, 0, 0 };
+
+	dev_dbg(&client->dev, "set config to (%d)\n", b1);
+
+	return zforce_send_wait(ts, &buf[0], ARRAY_SIZE(buf));
+}
+
+static int zforce_start(struct zforce_ts *ts)
+{
+	struct i2c_client *client = ts->client;
+	const struct zforce_ts_platdata *pdata = dev_get_platdata(&client->dev);
+	int ret;
+
+	dev_dbg(&client->dev, "starting device\n");
+
+	ret = zforce_command_wait(ts, COMMAND_INITIALIZE);
+	if (ret) {
+		dev_err(&client->dev, "Unable to initialize, %d\n", ret);
+		return ret;
+	}
+
+	ret = zforce_resolution(ts, pdata->x_max, pdata->y_max);
+	if (ret) {
+		dev_err(&client->dev, "Unable to set resolution, %d\n", ret);
+		goto error;
+	}
+
+	ret = zforce_scan_frequency(ts, 10, 50, 50);
+	if (ret) {
+		dev_err(&client->dev, "Unable to set scan frequency, %d\n",
+			ret);
+		goto error;
+	}
+
+	if (zforce_setconfig(ts, SETCONFIG_DUALTOUCH)) {
+		dev_err(&client->dev, "Unable to set config\n");
+		goto error;
+	}
+
+	/* start sending touch events */
+	ret = zforce_command(ts, COMMAND_DATAREQUEST);
+	if (ret) {
+		dev_err(&client->dev, "Unable to request data\n");
+		goto error;
+	}
+
+	/*
+	 * Per NN, initial cal. take max. of 200msec.
+	 * Allow time to complete this calibration
+	 */
+	msleep(200);
+
+	return 0;
+
+error:
+	zforce_command_wait(ts, COMMAND_DEACTIVATE);
+	return ret;
+}
+
+static int zforce_stop(struct zforce_ts *ts)
+{
+	struct i2c_client *client = ts->client;
+	int ret;
+
+	dev_dbg(&client->dev, "stopping device\n");
+
+	/* Deactivates touch sensing and puts the device into sleep. */
+	ret = zforce_command_wait(ts, COMMAND_DEACTIVATE);
+	if (ret != 0) {
+		dev_err(&client->dev, "could not deactivate device, %d\n",
+			ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int zforce_touch_event(struct zforce_ts *ts, u8 *payload)
+{
+	struct i2c_client *client = ts->client;
+	const struct zforce_ts_platdata *pdata = dev_get_platdata(&client->dev);
+	struct zforce_point point;
+	int count, i, num = 0;
+
+	count = payload[0];
+	if (count > ZFORCE_REPORT_POINTS) {
+		dev_warn(&client->dev, "to many coordinates %d, expected max %d\n",
+			 count, ZFORCE_REPORT_POINTS);
+		count = ZFORCE_REPORT_POINTS;
+	}
+
+	for (i = 0; i < count; i++) {
+		point.coord_x =
+			payload[9 * i + 2] << 8 | payload[9 * i + 1];
+		point.coord_y =
+			payload[9 * i + 4] << 8 | payload[9 * i + 3];
+
+		if (point.coord_x > pdata->x_max ||
+		    point.coord_y > pdata->y_max) {
+			dev_warn(&client->dev, "coordinates (%d,%d) invalid\n",
+				point.coord_x, point.coord_y);
+			point.coord_x = point.coord_y = 0;
+		}
+
+		point.state = payload[9 * i + 5] & 0x03;
+		point.id = (payload[9 * i + 5] & 0xfc) >> 2;
+
+		/* determine touch major, minor and orientation */
+		point.area_major = max(payload[9 * i + 6],
+					  payload[9 * i + 7]);
+		point.area_minor = min(payload[9 * i + 6],
+					  payload[9 * i + 7]);
+		point.orientation = payload[9 * i + 6] > payload[9 * i + 7];
+
+		point.pressure = payload[9 * i + 8];
+		point.prblty = payload[9 * i + 9];
+
+		dev_dbg(&client->dev,
+			"point %d/%d: state %d, id %d, pressure %d, prblty %d, x %d, y %d, amajor %d, aminor %d, ori %d\n",
+			i, count, point.state, point.id,
+			point.pressure, point.prblty,
+			point.coord_x, point.coord_y,
+			point.area_major, point.area_minor,
+			point.orientation);
+
+		/* the zforce id starts with "1", so needs to be decreased */
+		input_mt_slot(ts->input, point.id - 1);
+
+		input_mt_report_slot_state(ts->input, MT_TOOL_FINGER,
+						point.state != STATE_UP);
+
+		if (point.state != STATE_UP) {
+			input_report_abs(ts->input, ABS_MT_POSITION_X,
+					 point.coord_x);
+			input_report_abs(ts->input, ABS_MT_POSITION_Y,
+					 point.coord_y);
+			input_report_abs(ts->input, ABS_MT_TOUCH_MAJOR,
+					 point.area_major);
+			input_report_abs(ts->input, ABS_MT_TOUCH_MINOR,
+					 point.area_minor);
+			input_report_abs(ts->input, ABS_MT_ORIENTATION,
+					 point.orientation);
+			num++;
+		}
+	}
+
+	input_mt_sync_frame(ts->input);
+
+	input_mt_report_finger_count(ts->input, num);
+
+	input_sync(ts->input);
+
+	return 0;
+}
+
+static int zforce_read_packet(struct zforce_ts *ts, u8 *buf)
+{
+	struct i2c_client *client = ts->client;
+	int ret;
+
+	mutex_lock(&ts->access_mutex);
+
+	/* read 2 byte message header */
+	ret = i2c_master_recv(client, buf, 2);
+	if (ret < 0) {
+		dev_err(&client->dev, "error reading header: %d\n", ret);
+		goto unlock;
+	}
+
+	if (buf[PAYLOAD_HEADER] != FRAME_START) {
+		dev_err(&client->dev, "invalid frame start: %d\n", buf[0]);
+		ret = -EIO;
+		goto unlock;
+	}
+
+	if (buf[PAYLOAD_LENGTH] <= 0 || buf[PAYLOAD_LENGTH] > 255) {
+		dev_err(&client->dev, "invalid payload length: %d\n",
+			buf[PAYLOAD_LENGTH]);
+		ret = -EIO;
+		goto unlock;
+	}
+
+	/* read the message */
+	ret = i2c_master_recv(client, &buf[PAYLOAD_BODY], buf[PAYLOAD_LENGTH]);
+	if (ret < 0) {
+		dev_err(&client->dev, "error reading payload: %d\n", ret);
+		goto unlock;
+	}
+
+	dev_dbg(&client->dev, "read %d bytes for response command 0x%x\n",
+		buf[PAYLOAD_LENGTH], buf[PAYLOAD_BODY]);
+
+unlock:
+	mutex_unlock(&ts->access_mutex);
+	return ret;
+}
+
+static void zforce_complete(struct zforce_ts *ts, int cmd, int result)
+{
+	struct i2c_client *client = ts->client;
+
+	if (ts->command_waiting == cmd) {
+		dev_dbg(&client->dev, "completing command 0x%x\n", cmd);
+		ts->command_result = result;
+		complete(&ts->command_done);
+	} else {
+		dev_dbg(&client->dev, "command %d not for us\n", cmd);
+	}
+}
+
+static irqreturn_t zforce_interrupt(int irq, void *dev_id)
+{
+	struct zforce_ts *ts = dev_id;
+	struct i2c_client *client = ts->client;
+	const struct zforce_ts_platdata *pdata = dev_get_platdata(&client->dev);
+	int ret;
+	u8 payload_buffer[512];
+	u8 *payload;
+
+	/*
+	 * When suspended, emit a wakeup signal if necessary and return.
+	 * Due to the level-interrupt we will get re-triggered later.
+	 */
+	if (ts->suspended) {
+		if (device_may_wakeup(&client->dev))
+			pm_wakeup_event(&client->dev, 500);
+		msleep(20);
+		return IRQ_HANDLED;
+	}
+
+	dev_dbg(&client->dev, "handling interrupt\n");
+
+	/* Don't emit wakeup events from commands run by zforce_suspend */
+	if (!ts->suspending && device_may_wakeup(&client->dev))
+		pm_stay_awake(&client->dev);
+
+	while (!gpio_get_value(pdata->gpio_int)) {
+		ret = zforce_read_packet(ts, payload_buffer);
+		if (ret < 0) {
+			dev_err(&client->dev, "could not read packet, ret: %d\n",
+				ret);
+			break;
+		}
+
+		payload =  &payload_buffer[PAYLOAD_BODY];
+
+		switch (payload[RESPONSE_ID]) {
+		case NOTIFICATION_TOUCH:
+			/*
+			 * Always report touch-events received while
+			 * suspending, when being a wakeup source
+			 */
+			if (ts->suspending && device_may_wakeup(&client->dev))
+				pm_wakeup_event(&client->dev, 500);
+			zforce_touch_event(ts, &payload[RESPONSE_DATA]);
+			break;
+
+		case NOTIFICATION_BOOTCOMPLETE:
+			ts->boot_complete = payload[RESPONSE_DATA];
+			zforce_complete(ts, payload[RESPONSE_ID], 0);
+			break;
+
+		case RESPONSE_INITIALIZE:
+		case RESPONSE_DEACTIVATE:
+		case RESPONSE_SETCONFIG:
+		case RESPONSE_RESOLUTION:
+		case RESPONSE_SCANFREQ:
+			zforce_complete(ts, payload[RESPONSE_ID],
+					payload[RESPONSE_DATA]);
+			break;
+
+		case RESPONSE_STATUS:
+			/*
+			 * Version Payload Results
+			 * [2:major] [2:minor] [2:build] [2:rev]
+			 */
+			ts->version_major = (payload[RESPONSE_DATA + 1] << 8) |
+						payload[RESPONSE_DATA];
+			ts->version_minor = (payload[RESPONSE_DATA + 3] << 8) |
+						payload[RESPONSE_DATA + 2];
+			ts->version_build = (payload[RESPONSE_DATA + 5] << 8) |
+						payload[RESPONSE_DATA + 4];
+			ts->version_rev   = (payload[RESPONSE_DATA + 7] << 8) |
+						payload[RESPONSE_DATA + 6];
+			dev_dbg(&ts->client->dev, "Firmware Version %04x:%04x %04x:%04x\n",
+				ts->version_major, ts->version_minor,
+				ts->version_build, ts->version_rev);
+
+			zforce_complete(ts, payload[RESPONSE_ID], 0);
+			break;
+
+		case NOTIFICATION_INVALID_COMMAND:
+			dev_err(&ts->client->dev, "invalid command: 0x%x\n",
+				payload[RESPONSE_DATA]);
+			break;
+
+		default:
+			dev_err(&ts->client->dev, "unrecognized response id: 0x%x\n",
+				payload[RESPONSE_ID]);
+			break;
+		}
+	}
+
+	if (!ts->suspending && device_may_wakeup(&client->dev))
+		pm_relax(&client->dev);
+
+	dev_dbg(&client->dev, "finished interrupt\n");
+
+	return IRQ_HANDLED;
+}
+
+static int zforce_input_open(struct input_dev *dev)
+{
+	struct zforce_ts *ts = input_get_drvdata(dev);
+	int ret;
+
+	ret = zforce_start(ts);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void zforce_input_close(struct input_dev *dev)
+{
+	struct zforce_ts *ts = input_get_drvdata(dev);
+	struct i2c_client *client = ts->client;
+	int ret;
+
+	ret = zforce_stop(ts);
+	if (ret)
+		dev_warn(&client->dev, "stopping zforce failed\n");
+
+	return;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int zforce_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct zforce_ts *ts = i2c_get_clientdata(client);
+	struct input_dev *input = ts->input;
+	int ret = 0;
+
+	mutex_lock(&input->mutex);
+	ts->suspending = true;
+
+	/*
+	 * When configured as a wakeup source device should always wake
+	 * the system, therefore start device if necessary.
+	 */
+	if (device_may_wakeup(&client->dev)) {
+		dev_dbg(&client->dev, "suspend while being a wakeup source\n");
+
+		/* Need to start device, if not open, to be a wakeup source. */
+		if (!input->users) {
+			ret = zforce_start(ts);
+			if (ret)
+				goto unlock;
+		}
+
+		enable_irq_wake(client->irq);
+	} else if (input->users) {
+		dev_dbg(&client->dev, "suspend without being a wakeup source\n");
+
+		ret = zforce_stop(ts);
+		if (ret)
+			goto unlock;
+
+		disable_irq(client->irq);
+	}
+
+	ts->suspended = true;
+
+unlock:
+	ts->suspending = false;
+	mutex_unlock(&input->mutex);
+
+	return ret;
+}
+
+static int zforce_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct zforce_ts *ts = i2c_get_clientdata(client);
+	struct input_dev *input = ts->input;
+	int ret = 0;
+
+	mutex_lock(&input->mutex);
+
+	ts->suspended = false;
+
+	if (device_may_wakeup(&client->dev)) {
+		dev_dbg(&client->dev, "resume from being a wakeup source\n");
+
+		disable_irq_wake(client->irq);
+
+		/* need to stop device if it was not open on suspend */
+		if (!input->users) {
+			ret = zforce_stop(ts);
+			if (ret)
+				goto unlock;
+		}
+	} else if (input->users) {
+		dev_dbg(&client->dev, "resume without being a wakeup source\n");
+
+		enable_irq(client->irq);
+
+		ret = zforce_start(ts);
+		if (ret < 0)
+			goto unlock;
+	}
+
+unlock:
+	mutex_unlock(&input->mutex);
+
+	return ret;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(zforce_pm_ops, zforce_suspend, zforce_resume);
+
+static void zforce_reset(void *data)
+{
+	struct zforce_ts *ts = data;
+
+	gpio_set_value(ts->pdata->gpio_rst, 0);
+}
+
+static int zforce_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	const struct zforce_ts_platdata *pdata = dev_get_platdata(&client->dev);
+	struct zforce_ts *ts;
+	struct input_dev *input_dev;
+	int ret;
+
+	if (!pdata)
+		return -EINVAL;
+
+	ts = devm_kzalloc(&client->dev, sizeof(struct zforce_ts), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	ret = devm_gpio_request_one(&client->dev, pdata->gpio_int, GPIOF_IN,
+				    "zforce_ts_int");
+	if (ret) {
+		dev_err(&client->dev, "request of gpio %d failed, %d\n",
+			pdata->gpio_int, ret);
+		return ret;
+	}
+
+	ret = devm_gpio_request_one(&client->dev, pdata->gpio_rst,
+				    GPIOF_OUT_INIT_LOW, "zforce_ts_rst");
+	if (ret) {
+		dev_err(&client->dev, "request of gpio %d failed, %d\n",
+			pdata->gpio_rst, ret);
+		return ret;
+	}
+
+	ret = devm_add_action(&client->dev, zforce_reset, ts);
+	if (ret) {
+		dev_err(&client->dev, "failed to register reset action, %d\n",
+			ret);
+		return ret;
+	}
+
+	snprintf(ts->phys, sizeof(ts->phys),
+		 "%s/input0", dev_name(&client->dev));
+
+	input_dev = devm_input_allocate_device(&client->dev);
+	if (!input_dev) {
+		dev_err(&client->dev, "could not allocate input device\n");
+		return -ENOMEM;
+	}
+
+	mutex_init(&ts->access_mutex);
+	mutex_init(&ts->command_mutex);
+
+	ts->pdata = pdata;
+	ts->client = client;
+	ts->input = input_dev;
+
+	input_dev->name = "Neonode zForce touchscreen";
+	input_dev->phys = ts->phys;
+	input_dev->id.bustype = BUS_I2C;
+
+	input_dev->open = zforce_input_open;
+	input_dev->close = zforce_input_close;
+
+	__set_bit(EV_KEY, input_dev->evbit);
+	__set_bit(EV_SYN, input_dev->evbit);
+	__set_bit(EV_ABS, input_dev->evbit);
+
+	/* For multi touch */
+	input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0,
+			     pdata->x_max, 0, 0);
+	input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0,
+			     pdata->y_max, 0, 0);
+
+	input_set_abs_params(input_dev, ABS_MT_TOUCH_MAJOR, 0,
+			     ZFORCE_MAX_AREA, 0, 0);
+	input_set_abs_params(input_dev, ABS_MT_TOUCH_MINOR, 0,
+			     ZFORCE_MAX_AREA, 0, 0);
+	input_set_abs_params(input_dev, ABS_MT_ORIENTATION, 0, 1, 0, 0);
+	input_mt_init_slots(input_dev, ZFORCE_REPORT_POINTS, INPUT_MT_DIRECT);
+
+	input_set_drvdata(ts->input, ts);
+
+	init_completion(&ts->command_done);
+
+	/*
+	 * The zforce pulls the interrupt low when it has data ready.
+	 * After it is triggered the isr thread runs until all the available
+	 * packets have been read and the interrupt is high again.
+	 * Therefore we can trigger the interrupt anytime it is low and do
+	 * not need to limit it to the interrupt edge.
+	 */
+	ret = devm_request_threaded_irq(&client->dev, client->irq, NULL,
+					zforce_interrupt,
+					IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+					input_dev->name, ts);
+	if (ret) {
+		dev_err(&client->dev, "irq %d request failed\n", client->irq);
+		return ret;
+	}
+
+	i2c_set_clientdata(client, ts);
+
+	/* let the controller boot */
+	gpio_set_value(pdata->gpio_rst, 1);
+
+	ts->command_waiting = NOTIFICATION_BOOTCOMPLETE;
+	if (wait_for_completion_timeout(&ts->command_done, WAIT_TIMEOUT) == 0)
+		dev_warn(&client->dev, "bootcomplete timed out\n");
+
+	/* need to start device to get version information */
+	ret = zforce_command_wait(ts, COMMAND_INITIALIZE);
+	if (ret) {
+		dev_err(&client->dev, "unable to initialize, %d\n", ret);
+		return ret;
+	}
+
+	/* this gets the firmware version among other informations */
+	ret = zforce_command_wait(ts, COMMAND_STATUS);
+	if (ret < 0) {
+		dev_err(&client->dev, "couldn't get status, %d\n", ret);
+		zforce_stop(ts);
+		return ret;
+	}
+
+	/* stop device and put it into sleep until it is opened */
+	ret = zforce_stop(ts);
+	if (ret < 0)
+		return ret;
+
+	device_set_wakeup_capable(&client->dev, true);
+
+	ret = input_register_device(input_dev);
+	if (ret) {
+		dev_err(&client->dev, "could not register input device, %d\n",
+			ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static struct i2c_device_id zforce_idtable[] = {
+	{ "zforce-ts", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, zforce_idtable);
+
+static struct i2c_driver zforce_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= "zforce-ts",
+		.pm	= &zforce_pm_ops,
+	},
+	.probe		= zforce_probe,
+	.id_table	= zforce_idtable,
+};
+
+module_i2c_driver(zforce_driver);
+
+MODULE_AUTHOR("Heiko Stuebner <heiko@sntech.de>");
+MODULE_DESCRIPTION("zForce TouchScreen Driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/platform_data/zforce_ts.h b/include/linux/platform_data/zforce_ts.h
new file mode 100644
index 0000000..0472ab2
--- /dev/null
+++ b/include/linux/platform_data/zforce_ts.h
@@ -0,0 +1,26 @@
+/* drivers/input/touchscreen/zforce.c
+ *
+ * Copyright (C) 2012-2013 MundoReader S.L.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _LINUX_INPUT_ZFORCE_TS_H
+#define _LINUX_INPUT_ZFORCE_TS_H
+
+struct zforce_ts_platdata {
+	int gpio_int;
+	int gpio_rst;
+
+	unsigned int x_max;
+	unsigned int y_max;
+};
+
+#endif /* _LINUX_INPUT_ZFORCE_TS_H */