regulator: 88pm800: Fix indentation of assignments of data structures
This patch makes code more clean from readability point of view,
make all assignments of LDO, BUCk and regulator_ops structure
at the same indentation.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
diff --git a/drivers/regulator/88pm800.c b/drivers/regulator/88pm800.c
index 832932b..11f7ab2 100644
--- a/drivers/regulator/88pm800.c
+++ b/drivers/regulator/88pm800.c
@@ -95,11 +95,11 @@
#define PM800_BUCK(vreg, ereg, ebit, amax, volt_ranges, n_volt) \
{ \
.desc = { \
- .name = #vreg, \
- .ops = &pm800_volt_range_ops, \
- .type = REGULATOR_VOLTAGE, \
- .id = PM800_ID_##vreg, \
- .owner = THIS_MODULE, \
+ .name = #vreg, \
+ .ops = &pm800_volt_range_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = PM800_ID_##vreg, \
+ .owner = THIS_MODULE, \
.n_voltages = n_volt, \
.linear_ranges = volt_ranges, \
.n_linear_ranges = ARRAY_SIZE(volt_ranges), \
@@ -108,7 +108,7 @@
.enable_reg = PM800_##ereg, \
.enable_mask = 1 << (ebit), \
}, \
- .max_ua = (amax), \
+ .max_ua = (amax), \
}
/*
@@ -123,19 +123,19 @@
#define PM800_LDO(vreg, ereg, ebit, amax, ldo_volt_table) \
{ \
.desc = { \
- .name = #vreg, \
- .ops = &pm800_volt_table_ops, \
- .type = REGULATOR_VOLTAGE, \
- .id = PM800_ID_##vreg, \
- .owner = THIS_MODULE, \
- .n_voltages = ARRAY_SIZE(ldo_volt_table), \
- .vsel_reg = PM800_##vreg##_VOUT, \
- .vsel_mask = 0x1f, \
- .enable_reg = PM800_##ereg, \
- .enable_mask = 1 << (ebit), \
- .volt_table = ldo_volt_table, \
+ .name = #vreg, \
+ .ops = &pm800_volt_table_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = PM800_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = ARRAY_SIZE(ldo_volt_table), \
+ .vsel_reg = PM800_##vreg##_VOUT, \
+ .vsel_mask = 0x1f, \
+ .enable_reg = PM800_##ereg, \
+ .enable_mask = 1 << (ebit), \
+ .volt_table = ldo_volt_table, \
}, \
- .max_ua = (amax), \
+ .max_ua = (amax), \
}
/* Ranges are sorted in ascending order. */
@@ -178,25 +178,25 @@
}
static struct regulator_ops pm800_volt_range_ops = {
- .list_voltage = regulator_list_voltage_linear_range,
- .map_voltage = regulator_map_voltage_linear_range,
- .set_voltage_sel = regulator_set_voltage_sel_regmap,
- .get_voltage_sel = regulator_get_voltage_sel_regmap,
- .enable = regulator_enable_regmap,
- .disable = regulator_disable_regmap,
- .is_enabled = regulator_is_enabled_regmap,
- .get_current_limit = pm800_get_current_limit,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_current_limit = pm800_get_current_limit,
};
static struct regulator_ops pm800_volt_table_ops = {
- .list_voltage = regulator_list_voltage_table,
- .map_voltage = regulator_map_voltage_iterate,
- .set_voltage_sel = regulator_set_voltage_sel_regmap,
- .get_voltage_sel = regulator_get_voltage_sel_regmap,
- .enable = regulator_enable_regmap,
- .disable = regulator_disable_regmap,
- .is_enabled = regulator_is_enabled_regmap,
- .get_current_limit = pm800_get_current_limit,
+ .list_voltage = regulator_list_voltage_table,
+ .map_voltage = regulator_map_voltage_iterate,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_current_limit = pm800_get_current_limit,
};
/* The array is indexed by id(PM800_ID_XXX) */
