# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/ti,icssg-prueth.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Texas Instruments ICSSG PRUSS Ethernet

maintainers:
  - Md Danish Anwar <danishanwar@ti.com>

description:
  Ethernet based on the Programmable Real-Time Unit and Industrial
  Communication Subsystem.

properties:
  compatible:
    enum:
      - ti,am642-icssg-prueth      # for AM64x SoC family
      - ti,am654-icssg-prueth      # for AM65x SoC family
      - ti,am654-sr1-icssg-prueth  # for AM65x SoC family, SR1.0

  sram:
    $ref: /schemas/types.yaml#/definitions/phandle
    description:
      phandle to MSMC SRAM node

  dmas:
    minItems: 10
    maxItems: 12

  dma-names:
    minItems: 10
    items:
      - const: tx0-0
      - const: tx0-1
      - const: tx0-2
      - const: tx0-3
      - const: tx1-0
      - const: tx1-1
      - const: tx1-2
      - const: tx1-3
      - const: rx0
      - const: rx1
      - const: rxmgm0
      - const: rxmgm1

  ti,mii-g-rt:
    $ref: /schemas/types.yaml#/definitions/phandle
    description:
      phandle to MII_G_RT module's syscon regmap.

  ti,mii-rt:
    $ref: /schemas/types.yaml#/definitions/phandle
    description:
      phandle to MII_RT module's syscon regmap

  ti,pa-stats:
    $ref: /schemas/types.yaml#/definitions/phandle
    description:
      phandle to PA_STATS module's syscon regmap. PA_STATS is a set of
      registers where different statistics related to ICSSG, are dumped by
      ICSSG firmware. PA_STATS module's syscon regmap will help the device to
      access/read/write those statistics.

  ti,iep:
    $ref: /schemas/types.yaml#/definitions/phandle-array
    maxItems: 2
    items:
      maxItems: 1
    description:
      phandle to IEP (Industrial Ethernet Peripheral) for ICSSG

  interrupts:
    maxItems: 2
    description:
      Interrupt specifiers to TX timestamp IRQ.

  interrupt-names:
    items:
      - const: tx_ts0
      - const: tx_ts1

  ethernet-ports:
    type: object
    additionalProperties: false

    properties:
      '#address-cells':
        const: 1
      '#size-cells':
        const: 0

    patternProperties:
      ^port@[0-1]$:
        type: object
        description: ICSSG PRUETH external ports
        $ref: ethernet-controller.yaml#
        unevaluatedProperties: false

        properties:
          reg:
            items:
              - enum: [0, 1]
            description: ICSSG PRUETH port number

          interrupts:
            maxItems: 1

          ti,syscon-rgmii-delay:
            items:
              - items:
                  - description: phandle to system controller node
                  - description: The offset to ICSSG control register
            $ref: /schemas/types.yaml#/definitions/phandle-array
            description:
              phandle to system controller node and register offset
              to ICSSG control register for RGMII transmit delay

          ti,half-duplex-capable:
            type: boolean
            description:
              Indicates that the PHY output pin COL is routed to ICSSG GPIO pin
              (PRGx_PRU0/1_GPIO10) as input so that the ICSSG MII port is
              capable of half duplex operations.

        required:
          - reg
    anyOf:
      - required:
          - port@0
      - required:
          - port@1

required:
  - compatible
  - sram
  - dmas
  - dma-names
  - ethernet-ports
  - ti,mii-g-rt
  - interrupts
  - interrupt-names

allOf:
  - $ref: /schemas/remoteproc/ti,pru-consumer.yaml#

  - if:
      properties:
        compatible:
          contains:
            const: ti,am654-sr1-icssg-prueth
    then:
      properties:
        dmas:
          minItems: 12
        dma-names:
          minItems: 12
    else:
      properties:
        dmas:
          maxItems: 10
        dma-names:
          maxItems: 10

unevaluatedProperties: false

examples:
  - |
    /* Example k3-am654 base board SR2.0, dual-emac */
    pruss2_eth: ethernet {
        compatible = "ti,am654-icssg-prueth";
        pinctrl-names = "default";
        pinctrl-0 = <&icssg2_rgmii_pins_default>;
        sram = <&msmc_ram>;

        ti,prus = <&pru2_0>, <&rtu2_0>, <&tx_pru2_0>,
                  <&pru2_1>, <&rtu2_1>, <&tx_pru2_1>;
        firmware-name = "ti-pruss/am65x-pru0-prueth-fw.elf",
                        "ti-pruss/am65x-rtu0-prueth-fw.elf",
                        "ti-pruss/am65x-txpru0-prueth-fw.elf",
                        "ti-pruss/am65x-pru1-prueth-fw.elf",
                        "ti-pruss/am65x-rtu1-prueth-fw.elf",
                        "ti-pruss/am65x-txpru1-prueth-fw.elf";
        ti,pruss-gp-mux-sel = <2>,      /* MII mode */
                              <2>,
                              <2>,
                              <2>,      /* MII mode */
                              <2>,
                              <2>;
        dmas = <&main_udmap 0xc300>, /* egress slice 0 */
               <&main_udmap 0xc301>, /* egress slice 0 */
               <&main_udmap 0xc302>, /* egress slice 0 */
               <&main_udmap 0xc303>, /* egress slice 0 */
               <&main_udmap 0xc304>, /* egress slice 1 */
               <&main_udmap 0xc305>, /* egress slice 1 */
               <&main_udmap 0xc306>, /* egress slice 1 */
               <&main_udmap 0xc307>, /* egress slice 1 */
               <&main_udmap 0x4300>, /* ingress slice 0 */
               <&main_udmap 0x4301>; /* ingress slice 1 */
        dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
                    "tx1-0", "tx1-1", "tx1-2", "tx1-3",
                    "rx0", "rx1";
        ti,mii-g-rt = <&icssg2_mii_g_rt>;
        ti,pa-stats = <&icssg2_pa_stats>;
        ti,iep = <&icssg2_iep0>, <&icssg2_iep1>;
        interrupt-parent = <&icssg2_intc>;
        interrupts = <24 0 2>, <25 1 3>;
        interrupt-names = "tx_ts0", "tx_ts1";
        ethernet-ports {
            #address-cells = <1>;
            #size-cells = <0>;
            pruss2_emac0: port@0 {
                reg = <0>;
                phy-handle = <&pruss2_eth0_phy>;
                phy-mode = "rgmii-id";
                interrupts-extended = <&icssg2_intc 24>;
                ti,syscon-rgmii-delay = <&scm_conf 0x4120>;
                /* Filled in by bootloader */
                local-mac-address = [00 00 00 00 00 00];
            };

            pruss2_emac1: port@1 {
                reg = <1>;
                phy-handle = <&pruss2_eth1_phy>;
                phy-mode = "rgmii-id";
                interrupts-extended = <&icssg2_intc 25>;
                ti,syscon-rgmii-delay = <&scm_conf 0x4124>;
                /* Filled in by bootloader */
                local-mac-address = [00 00 00 00 00 00];
            };
        };
    };