| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/net/dsa/qca8k.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: Qualcomm Atheros QCA83xx switch family |
| |
| maintainers: |
| - John Crispin <john@phrozen.org> |
| |
| description: |
| If the QCA8K switch is connect to an SoC's external mdio-bus, each subnode |
| describing a port needs to have a valid phandle referencing the internal PHY |
| it is connected to. This is because there is no N:N mapping of port and PHY |
| ID. To declare the internal mdio-bus configuration, declare an MDIO node in |
| the switch node and declare the phandle for the port, referencing the internal |
| PHY it is connected to. In this config, an internal mdio-bus is registered and |
| the MDIO master is used for communication. Mixed external and internal |
| mdio-bus configurations are not supported by the hardware. |
| Each phy has at most 3 LEDs connected and can be declared |
| using the standard LEDs structure. |
| |
| properties: |
| compatible: |
| oneOf: |
| - enum: |
| - qca,qca8327 |
| - qca,qca8328 |
| - qca,qca8334 |
| - qca,qca8337 |
| description: | |
| qca,qca8328: referenced as AR8328(N)-AK1(A/B) QFN 176 pin package |
| qca,qca8327: referenced as AR8327(N)-AL1A DR-QFN 148 pin package |
| qca,qca8334: referenced as QCA8334-AL3C QFN 88 pin package |
| qca,qca8337: referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package |
| |
| reg: |
| maxItems: 1 |
| |
| reset-gpios: |
| description: |
| GPIO to be used to reset the whole device |
| maxItems: 1 |
| |
| qca,ignore-power-on-sel: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| Ignore power-on pin strapping to configure LED open-drain or EEPROM |
| presence. This is needed for devices with incorrect configuration or when |
| the OEM has decided not to use pin strapping and falls back to SW regs. |
| |
| qca,led-open-drain: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| Set LEDs to open-drain mode. This requires the qca,ignore-power-on-sel to |
| be set, otherwise the driver will fail at probe. This is required if the |
| OEM does not use pin strapping to set this mode and prefers to set it |
| using SW regs. The pin strappings related to LED open-drain mode are |
| B68 on the QCA832x and B49 on the QCA833x. |
| |
| mdio: |
| $ref: /schemas/net/mdio.yaml# |
| unevaluatedProperties: false |
| description: Qca8k switch have an internal mdio to access switch port. |
| If this is not present, the legacy mapping is used and the |
| internal mdio access is used. |
| With the legacy mapping the reg corresponding to the internal |
| mdio is the switch reg with an offset of -1. |
| |
| $ref: dsa.yaml# |
| |
| patternProperties: |
| "^(ethernet-)?ports$": |
| type: object |
| additionalProperties: true |
| patternProperties: |
| "^(ethernet-)?port@[0-6]$": |
| type: object |
| description: Ethernet switch ports |
| |
| $ref: dsa-port.yaml# |
| |
| properties: |
| qca,sgmii-rxclk-falling-edge: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| Set the receive clock phase to falling edge. Mostly commonly used on |
| the QCA8327 with CPU port 0 set to SGMII. |
| |
| qca,sgmii-txclk-falling-edge: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| Set the transmit clock phase to falling edge. |
| |
| qca,sgmii-enable-pll: |
| $ref: /schemas/types.yaml#/definitions/flag |
| description: |
| For SGMII CPU port, explicitly enable PLL, TX and RX chain along with |
| Signal Detection. On the QCA8327 this should not be enabled, otherwise |
| the SGMII port will not initialize. When used on the QCA8337, revision 3 |
| or greater, a warning will be displayed. When the CPU port is set to |
| SGMII on the QCA8337, it is advised to set this unless a communication |
| issue is observed. |
| |
| unevaluatedProperties: false |
| |
| oneOf: |
| - required: |
| - ports |
| - required: |
| - ethernet-ports |
| |
| required: |
| - compatible |
| - reg |
| |
| unevaluatedProperties: false |
| |
| examples: |
| - | |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| external_phy_port1: ethernet-phy@0 { |
| reg = <0>; |
| }; |
| |
| external_phy_port2: ethernet-phy@1 { |
| reg = <1>; |
| }; |
| |
| external_phy_port3: ethernet-phy@2 { |
| reg = <2>; |
| }; |
| |
| external_phy_port4: ethernet-phy@3 { |
| reg = <3>; |
| }; |
| |
| external_phy_port5: ethernet-phy@4 { |
| reg = <4>; |
| }; |
| |
| switch@10 { |
| compatible = "qca,qca8337"; |
| reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; |
| reg = <0x10>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| ethernet = <&gmac1>; |
| phy-mode = "rgmii"; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| label = "lan1"; |
| phy-handle = <&external_phy_port1>; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| label = "lan2"; |
| phy-handle = <&external_phy_port2>; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| label = "lan3"; |
| phy-handle = <&external_phy_port3>; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| label = "lan4"; |
| phy-handle = <&external_phy_port4>; |
| }; |
| |
| port@5 { |
| reg = <5>; |
| label = "wan"; |
| phy-handle = <&external_phy_port5>; |
| }; |
| }; |
| }; |
| }; |
| - | |
| #include <dt-bindings/gpio/gpio.h> |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch@10 { |
| compatible = "qca,qca8337"; |
| reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; |
| reg = <0x10>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| ethernet = <&gmac1>; |
| phy-mode = "rgmii"; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| label = "lan1"; |
| phy-mode = "internal"; |
| phy-handle = <&internal_phy_port1>; |
| |
| leds { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@0 { |
| reg = <0>; |
| color = <LED_COLOR_ID_WHITE>; |
| function = LED_FUNCTION_LAN; |
| default-state = "keep"; |
| }; |
| |
| led@1 { |
| reg = <1>; |
| color = <LED_COLOR_ID_AMBER>; |
| function = LED_FUNCTION_LAN; |
| default-state = "keep"; |
| }; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| label = "lan2"; |
| phy-mode = "internal"; |
| phy-handle = <&internal_phy_port2>; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| label = "lan3"; |
| phy-mode = "internal"; |
| phy-handle = <&internal_phy_port3>; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| label = "lan4"; |
| phy-mode = "internal"; |
| phy-handle = <&internal_phy_port4>; |
| }; |
| |
| port@5 { |
| reg = <5>; |
| label = "wan"; |
| phy-mode = "internal"; |
| phy-handle = <&internal_phy_port5>; |
| }; |
| |
| port@6 { |
| reg = <0>; |
| ethernet = <&gmac1>; |
| phy-mode = "sgmii"; |
| |
| qca,sgmii-rxclk-falling-edge; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| }; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| internal_phy_port1: ethernet-phy@0 { |
| reg = <0>; |
| }; |
| |
| internal_phy_port2: ethernet-phy@1 { |
| reg = <1>; |
| }; |
| |
| internal_phy_port3: ethernet-phy@2 { |
| reg = <2>; |
| }; |
| |
| internal_phy_port4: ethernet-phy@3 { |
| reg = <3>; |
| }; |
| |
| internal_phy_port5: ethernet-phy@4 { |
| reg = <4>; |
| }; |
| }; |
| }; |
| }; |
