// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
 * Copyright (C) 2023 DH electronics GmbH
 */

#include "imx6ull-dhcor-som.dtsi"

/ {
	aliases {
		/delete-property/ mmc0; /* Avoid double definitions */
		/delete-property/ mmc1;
		/delete-property/ spi2;
		/delete-property/ spi3;
		i2c0 = &i2c2;
		i2c1 = &i2c1;
		mmc2 = &usdhc2;
		rtc0 = &rtc_i2c;
		rtc1 = &snvs_rtc;
		serial0 = &uart1;
		serial1 = &uart6; /* DHCOM UART2, special hardware required */
		serial2 = &uart3;
		serial3 = &uart2; /* Use BT UART always as ttymxc3 */
		serial4 = &uart4;
		serial5 = &uart5;
		spi0 = &ecspi1;
		spi1 = &ecspi4; /* DHCOM SPI2, special hardware required */
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	reg_ext_3v3_ref: regulator-ext-3v3-ref {
		compatible = "regulator-fixed";
		regulator-always-on;
		regulator-max-microvolt = <3300000>;
		regulator-min-microvolt = <3300000>;
		regulator-name = "VCC_3V3_REF";
	};

	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
		compatible = "regulator-fixed";
		regulator-max-microvolt = <5000000>;
		regulator-min-microvolt = <5000000>;
		regulator-name = "usb-otg1-vbus";
	};

	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
		compatible = "regulator-fixed";
		gpio = <&gpio1 5 GPIO_ACTIVE_LOW>;
		regulator-max-microvolt = <5000000>;
		regulator-min-microvolt = <5000000>;
		regulator-name = "usb-otg2-vbus";
	};

	/* SoM with WiFi/BT: WiFi pin WL_REG_ON is connected to a DHCOM GPIO */
	/omit-if-no-ref/ usdhc1_pwrseq: usdhc1-pwrseq {
		compatible = "mmc-pwrseq-simple";
		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; /* GPIO H */
	};
};

/* SoM with WiFi/BT: BT pin BT_REG_ON is connected to a DHCOM GPIO */
&bluetooth {
	shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
};

&can1 {
	pinctrl-0 = <&pinctrl_flexcan1>;
	pinctrl-names = "default";
	status = "okay";
};

/*
 * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
 * Only if this pins are used as CAN interface enable it on board layer.
 */
&can2 {
	pinctrl-0 = <&pinctrl_flexcan2>;
	pinctrl-names = "default";
};

/* DHCOM SPI1 */
&ecspi1 {
	cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
	pinctrl-0 = <&pinctrl_ecspi1>;
	pinctrl-names = "default";
	status = "okay";
};

/*
 * DHCOM SPI2
 * Special hardware required that uses the pins of FEC2. Therefore this SPI
 * interface can only be used if FEC2 is disabled.
 */
&ecspi4 {
	cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
	pinctrl-0 = <&pinctrl_ecspi4>;
	pinctrl-names = "default";
};

/* DHCOM ETH1 */
&fec1 {
	phy-handle = <&mdio2_phy0>;
	phy-mode = "rmii";
	pinctrl-0 = <&pinctrl_fec1>;
	pinctrl-names = "default";
	status = "okay";
};

/* DHCOM ETH2 */
&fec2 {
	phy-handle = <&mdio2_phy1>;
	phy-mode = "rmii";
	pinctrl-0 = <&pinctrl_fec2>;
	pinctrl-names = "default";
	status = "okay";

	mdio {
		#address-cells = <1>;
		#size-cells = <0>;

		mdio2_phy0: ethernet-phy@0 {
			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
				     "ethernet-phy-ieee802.3-c22";
			reg = <0>;
			clock-names = "rmii-ref";
			clocks = <&clks IMX6UL_CLK_ENET_REF>;
			interrupt-parent = <&gpio5>;
			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
			pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
			pinctrl-names = "default";
			reset-assert-us = <500>;
			reset-deassert-us = <500>;
			reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
			smsc,disable-energy-detect; /* Make plugin detection reliable */
		};

		mdio2_phy1: ethernet-phy@1 {
			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
				     "ethernet-phy-ieee802.3-c22";
			reg = <1>;
			clock-names = "rmii-ref";
			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
			interrupt-parent = <&gpio5>;
			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
			pinctrl-0 = <&pinctrl_fec2_phy &pinctrl_snvs_fec2_phy>;
			pinctrl-names = "default";
			reset-assert-us = <500>;
			reset-deassert-us = <500>;
			reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
			smsc,disable-energy-detect; /* Make plugin detection reliable */
		};
	};
};

&gpio1 {
	gpio-line-names =
		"", "", "", "",
		"", "", "", "",
		"", "", "", "DHCOM-INT",
		"", "", "", "",
		"", "", "DHCOM-I", "",
		"", "", "", "",
		"", "", "", "",
		"", "", "", "";
	pinctrl-0 = <&pinctrl_spi1_switch
		     &pinctrl_dhcom_i &pinctrl_dhcom_int>;
	pinctrl-names = "default";
};

&gpio4 {
	gpio-line-names =
		"", "", "", "",
		"", "", "", "",
		"", "", "", "",
		"", "", "", "",
		"", "DHCOM-L", "DHCOM-K", "DHCOM-M",
		"DHCOM-J", "DHCOM-U", "DHCOM-T", "DHCOM-S",
		"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
		"DHCOM-N", "", "", "";
	pinctrl-0 = <&pinctrl_dhcom_j &pinctrl_dhcom_k
		     &pinctrl_dhcom_l &pinctrl_dhcom_m
		     &pinctrl_dhcom_n &pinctrl_dhcom_o
		     &pinctrl_dhcom_p &pinctrl_dhcom_q
		     &pinctrl_dhcom_r &pinctrl_dhcom_s
		     &pinctrl_dhcom_t &pinctrl_dhcom_u>;
	pinctrl-names = "default";
};

&gpio5 {
	gpio-line-names =
		"DHCOM-A", "DHCOM-B", "DHCOM-C", "DHCOM-D",
		"DHCOM-E", "", "", "DHCOM-F",
		"DHCOM-G", "DHCOM-H", "", "",
		"", "", "", "",
		"", "", "", "",
		"", "", "", "",
		"", "", "", "",
		"", "", "", "";
	pinctrl-0 = <&pinctrl_snvs_dhcom_a &pinctrl_snvs_dhcom_b
		     &pinctrl_snvs_dhcom_c &pinctrl_snvs_dhcom_d
		     &pinctrl_snvs_dhcom_e &pinctrl_snvs_dhcom_f
		     &pinctrl_snvs_dhcom_g &pinctrl_snvs_dhcom_h>;
	pinctrl-names = "default";
};

/* DHCOM I2C2 */
&i2c1 {
	rtc_i2c: rtc@32 {
		compatible = "microcrystal,rv8803";
		reg = <0x32>;
	};

	/* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH1 */
	eeprom@50 {
		compatible = "atmel,24c02";
		reg = <0x50>;
		pagesize = <16>;
	};

	/* TI ADC101C027 */
	adc@51 {
		compatible = "ti,adc101c";
		reg = <0x51>;
		vref-supply = <&reg_ext_3v3_ref>;
	};

	/* TI ADC101C027 */
	adc@52 {
		compatible = "ti,adc101c";
		reg = <0x52>;
		vref-supply = <&reg_ext_3v3_ref>;
	};

	/* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH2 */
	eeprom@53 {
		compatible = "atmel,24c02";
		reg = <0x53>;
		pagesize = <16>;
	};
};

/* DHCOM I2C1 */
&i2c2 {
	clock-frequency = <100000>;
	pinctrl-0 = <&pinctrl_i2c2>;
	pinctrl-1 = <&pinctrl_i2c2_gpio>;
	pinctrl-names = "default", "gpio";
	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
	sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
	status = "okay";
};

&lcdif {
	pinctrl-0 = <&pinctrl_lcdif>;
	pinctrl-names = "default";
};

&pwm1 {
	pinctrl-0 = <&pinctrl_pwm1>;
	pinctrl-names = "default";
};

&sai2 {
	assigned-clock-rates = <320000000>;
	assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>;
	pinctrl-0 = <&pinctrl_sai2>;
	pinctrl-names = "default";
};

&tsc {
	measure-delay-time = <0xffff>;
	pinctrl-0 = <&pinctrl_tsc>;
	pinctrl-names = "default";
	pre-charge-time = <0xfff>;
	touchscreen-average-samples = <32>;
	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
};

/* DHCOM UART1 */
&uart1 {
	pinctrl-0 = <&pinctrl_uart1>;
	pinctrl-names = "default";
	status = "okay";
};

/*
 * DHCOM UART2 (alternative)
 * Special hardware required that uses DHCOM GPIO pins for DHCOM UART2.
 * Therefore this UART interface can only be used if DHCOM GPIOs J/K/L/M are
 * removed from GPIO hog muxing.
 */
&uart6 {
	pinctrl-0 = <&pinctrl_uart6>;
	pinctrl-names = "default";
	uart-has-rtscts;
};

&usbotg1 {
	adp-disable;
	disable-over-current;
	dr_mode = "otg";
	hnp-disable;
	pinctrl-0 = <&pinctrl_usbotg1>;
	pinctrl-names = "default";
	srp-disable;
	vbus-supply = <&reg_usb_otg1_vbus>;
	status = "okay";
};

&usbotg2 {
	disable-over-current; /* Overcurrent pin is used for TSC */
	dr_mode = "host";
	pinctrl-0 = <&pinctrl_usbotg2>;
	pinctrl-names = "default";
	tpl-support;
	vbus-supply = <&reg_usb_otg2_vbus>;
	status = "okay";
};

&usbphy1 {
	fsl,tx-d-cal = <106>;
};

&usbphy2 {
	fsl,tx-d-cal = <106>;
};

/* WiFi on LGA */
&usdhc1 {
	mmc-pwrseq = <&usdhc1_pwrseq>;
};

/* eMMC on module */
&usdhc2 {
	bus-width = <8>;
	no-1-8-v;
	non-removable;
	pinctrl-0 = <&pinctrl_usdhc2>;
	pinctrl-names = "default";
	vmmc-supply = <&vcc_3v3>;
	vqmmc-supply = <&vcc_3v3>;
	status = "okay";
};

&iomuxc {
	/* DHCOM GPIOs I..U + INT_HIGHEST_PRIORITY */
	pinctrl_dhcom_i: dhcom-i-grp {
		fsl,pins = <MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x400120b0>;
	};

	pinctrl_dhcom_j: dhcom-j-grp {
		fsl,pins = <MX6UL_PAD_CSI_HSYNC__GPIO4_IO20	0x400120b0>;
	};

	pinctrl_dhcom_k: dhcom-k-grp {
		fsl,pins = <MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x400120b0>;
	};

	pinctrl_dhcom_l: dhcom-l-grp {
		fsl,pins = <MX6UL_PAD_CSI_MCLK__GPIO4_IO17	0x400120b0>;
	};

	pinctrl_dhcom_m: dhcom-m-grp {
		fsl,pins = <MX6UL_PAD_CSI_VSYNC__GPIO4_IO19	0x400120b0>;
	};

	pinctrl_dhcom_n: dhcom-n-grp {
		fsl,pins = <MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x400120b0>;
	};

	pinctrl_dhcom_o: dhcom-o-grp {
		fsl,pins = <MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x400120b0>;
	};

	pinctrl_dhcom_p: dhcom-p-grp {
		fsl,pins = <MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x400120b0>;
	};

	pinctrl_dhcom_q: dhcom-q-grp {
		fsl,pins = <MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x400120b0>;
	};

	pinctrl_dhcom_r: dhcom-r-grp {
		fsl,pins = <MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x400120b0>;
	};

	pinctrl_dhcom_s: dhcom-s-grp {
		fsl,pins = <MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x400120b0>;
	};

	pinctrl_dhcom_t: dhcom-t-grp {
		fsl,pins = <MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x400120b0>;
	};

	pinctrl_dhcom_u: dhcom-u-grp {
		fsl,pins = <MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x400120b0>;
	};

	pinctrl_dhcom_int: dhcom-int-grp {
		fsl,pins = <MX6UL_PAD_JTAG_TMS__GPIO1_IO11	0x400120b0>;
	};

	pinctrl_ecspi1: ecspi1-grp {
		fsl,pins = <
			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100b1
			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x100b1
			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x100b1
			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x1b0b0 /* SS0 */
		>;
	};

	pinctrl_ecspi4: ecspi4-grp {
		fsl,pins = <
			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO	0x100b1
			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI	0x100b1
			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK	0x100b1
			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b0b0 /* SS0 */
		>;
	};

	pinctrl_fec1: fec1-grp {
		fsl,pins = <
			/* FEC1 uses MDIO bus from FEC2 */
			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b010
			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b010
			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b010
			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b010
		>;
	};

	pinctrl_fec1_phy: fec1-phy-grp {
		fsl,pins = <
			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0xb0 /* SMSC PHY reset */
		>;
	};

	pinctrl_fec2: fec2-grp {
		fsl,pins = <
			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b010
			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b010
			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b010
			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b010
		>;
	};

	pinctrl_fec2_phy: fec2-phy-grp {
		fsl,pins = <
			MX6UL_PAD_LCD_DATA19__GPIO3_IO24	0xb0 /* SMSC PHY reset */
		>;
	};

	pinctrl_flexcan1: flexcan1-grp {
		fsl,pins = <
			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
		>;
	};

	pinctrl_flexcan2: flexcan2-grp {
		fsl,pins = <
			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
		>;
	};

	pinctrl_i2c2: i2c2-grp {
		fsl,pins = <
			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001b8b0
			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001b8b0
		>;
	};

	pinctrl_i2c2_gpio: i2c2-gpio-grp {
		fsl,pins = <
			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x4001b8b0
			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	0x4001b8b0
		>;
	};

	pinctrl_lcdif: lcdif-grp {
		fsl,pins = <
			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
		>;
	};

	pinctrl_pwm1: pwm1-grp {
		fsl,pins = <
			MX6UL_PAD_GPIO1_IO08__PWM1_OUT		0x110b0
		>;
	};

	pinctrl_sai2: sai2-grp {
		fsl,pins = <
			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
		>;
	};

	pinctrl_tsc: tsc-grp {
		fsl,pins = <
			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0xb0
		>;
	};

	pinctrl_uart1: uart1-grp {
		fsl,pins = <
			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
		>;
	};

	pinctrl_uart6: uart6-grp {
		fsl,pins = <
			MX6UL_PAD_CSI_MCLK__UART6_DCE_TX	0x1b0b1
			MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX	0x1b0b1
			MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS	0x1b0b1
			MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS	0x1b0b1
		>;
	};

	pinctrl_usbotg1: usbotg1-grp {
		fsl,pins = <
			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
		>;
	};

	pinctrl_usbotg2: usbotg2-grp {
		fsl,pins = <
			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x120b0
		>;
	};

	pinctrl_usdhc2: usdhc2-grp {
		fsl,pins = <
			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B	0x17059 /* SD2 Reset */
		>;
	};
};

&iomuxc_snvs {
	/* DHCOM GPIOs A..H */
	pinctrl_snvs_dhcom_a: snvs-dhcom-a-grp {
		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x400120b0>;
	};

	pinctrl_snvs_dhcom_b: snvs-dhcom-b-grp {
		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x400120b0>;
	};

	pinctrl_snvs_dhcom_c: snvs-dhcom-c-grp {
		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x400120b0>;
	};

	pinctrl_snvs_dhcom_d: snvs-dhcom-d-grp {
		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x400120b0>;
	};

	pinctrl_snvs_dhcom_e: snvs-dhcom-e-grp {
		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x400120b0>;
	};

	pinctrl_snvs_dhcom_f: snvs-dhcom-f-grp {
		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x400120b0>;
	};

	pinctrl_snvs_dhcom_g: snvs-dhcom-g-grp {
		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x400120b0>;
	};

	pinctrl_snvs_dhcom_h: snvs-dhcom-h-grp {
		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400120b0>;
	};

	pinctrl_snvs_fec1_phy: snvs-fec1-phy-grp {
		fsl,pins = <
			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0xb1 /* SMSC PHY Int */
		>;
	};

	pinctrl_snvs_fec2_phy: snvs-fec2-phy-grp {
		fsl,pins = <
			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0xb1 /* SMSC PHY Int */
		>;
	};
};