| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Definitions for the PLX-9052 PCI interface chip |
| * |
| * Copyright (C) 2002 MEV Ltd. <https://www.mev.co.uk/> |
| * |
| * COMEDI - Linux Control and Measurement Device Interface |
| * Copyright (C) 2000 David A. Schleef <ds@schleef.org> |
| */ |
| |
| #ifndef _PLX9052_H_ |
| #define _PLX9052_H_ |
| |
| /* |
| * INTCSR - Interrupt Control/Status register |
| */ |
| #define PLX9052_INTCSR 0x4c |
| #define PLX9052_INTCSR_LI1ENAB BIT(0) /* LI1 enabled */ |
| #define PLX9052_INTCSR_LI1POL BIT(1) /* LI1 active high */ |
| #define PLX9052_INTCSR_LI1STAT BIT(2) /* LI1 active */ |
| #define PLX9052_INTCSR_LI2ENAB BIT(3) /* LI2 enabled */ |
| #define PLX9052_INTCSR_LI2POL BIT(4) /* LI2 active high */ |
| #define PLX9052_INTCSR_LI2STAT BIT(5) /* LI2 active */ |
| #define PLX9052_INTCSR_PCIENAB BIT(6) /* PCIINT enabled */ |
| #define PLX9052_INTCSR_SOFTINT BIT(7) /* generate soft int */ |
| #define PLX9052_INTCSR_LI1SEL BIT(8) /* LI1 edge */ |
| #define PLX9052_INTCSR_LI2SEL BIT(9) /* LI2 edge */ |
| #define PLX9052_INTCSR_LI1CLRINT BIT(10) /* LI1 clear int */ |
| #define PLX9052_INTCSR_LI2CLRINT BIT(11) /* LI2 clear int */ |
| #define PLX9052_INTCSR_ISAMODE BIT(12) /* ISA interface mode */ |
| |
| /* |
| * CNTRL - User I/O, Direct Slave Response, Serial EEPROM, and |
| * Initialization Control register |
| */ |
| #define PLX9052_CNTRL 0x50 |
| #define PLX9052_CNTRL_WAITO BIT(0) /* UIO0 or WAITO# select */ |
| #define PLX9052_CNTRL_UIO0_DIR BIT(1) /* UIO0 direction */ |
| #define PLX9052_CNTRL_UIO0_DATA BIT(2) /* UIO0 data */ |
| #define PLX9052_CNTRL_LLOCKO BIT(3) /* UIO1 or LLOCKo# select */ |
| #define PLX9052_CNTRL_UIO1_DIR BIT(4) /* UIO1 direction */ |
| #define PLX9052_CNTRL_UIO1_DATA BIT(5) /* UIO1 data */ |
| #define PLX9052_CNTRL_CS2 BIT(6) /* UIO2 or CS2# select */ |
| #define PLX9052_CNTRL_UIO2_DIR BIT(7) /* UIO2 direction */ |
| #define PLX9052_CNTRL_UIO2_DATA BIT(8) /* UIO2 data */ |
| #define PLX9052_CNTRL_CS3 BIT(9) /* UIO3 or CS3# select */ |
| #define PLX9052_CNTRL_UIO3_DIR BIT(10) /* UIO3 direction */ |
| #define PLX9052_CNTRL_UIO3_DATA BIT(11) /* UIO3 data */ |
| #define PLX9052_CNTRL_PCIBAR(x) (((x) & 0x3) << 12) |
| #define PLX9052_CNTRL_PCIBAR01 PLX9052_CNTRL_PCIBAR(0) /* mem and IO */ |
| #define PLX9052_CNTRL_PCIBAR0 PLX9052_CNTRL_PCIBAR(1) /* mem only */ |
| #define PLX9052_CNTRL_PCIBAR1 PLX9052_CNTRL_PCIBAR(2) /* IO only */ |
| #define PLX9052_CNTRL_PCI2_1_FEATURES BIT(14) /* PCI v2.1 features enabled */ |
| #define PLX9052_CNTRL_PCI_R_W_FLUSH BIT(15) /* read w/write flush mode */ |
| #define PLX9052_CNTRL_PCI_R_NO_FLUSH BIT(16) /* read no flush mode */ |
| #define PLX9052_CNTRL_PCI_R_NO_WRITE BIT(17) /* read no write mode */ |
| #define PLX9052_CNTRL_PCI_W_RELEASE BIT(18) /* write release bus mode */ |
| #define PLX9052_CNTRL_RETRY_CLKS(x) (((x) & 0xf) << 19) /* retry clks */ |
| #define PLX9052_CNTRL_LOCK_ENAB BIT(23) /* slave LOCK# enable */ |
| #define PLX9052_CNTRL_EEPROM_MASK (0x1f << 24) /* EEPROM bits */ |
| #define PLX9052_CNTRL_EEPROM_CLK BIT(24) /* EEPROM clock */ |
| #define PLX9052_CNTRL_EEPROM_CS BIT(25) /* EEPROM chip select */ |
| #define PLX9052_CNTRL_EEPROM_DOUT BIT(26) /* EEPROM write bit */ |
| #define PLX9052_CNTRL_EEPROM_DIN BIT(27) /* EEPROM read bit */ |
| #define PLX9052_CNTRL_EEPROM_PRESENT BIT(28) /* EEPROM present */ |
| #define PLX9052_CNTRL_RELOAD_CFG BIT(29) /* reload configuration */ |
| #define PLX9052_CNTRL_PCI_RESET BIT(30) /* PCI adapter reset */ |
| #define PLX9052_CNTRL_MASK_REV BIT(31) /* mask revision */ |
| |
| #endif /* _PLX9052_H_ */ |