// SPDX-License-Identifier: GPL-2.0-only
/*
 * Loongson-2K/Loongson LS7A I2C controller mode driver
 *
 * Copyright (C) 2013 Loongson Technology Corporation Limited.
 * Copyright (C) 2014-2017 Lemote, Inc.
 * Copyright (C) 2018-2022 Loongson Technology Corporation Limited.
 *
 * Originally written by liushaozong
 * Rewritten for mainline by Binbin Zhou <zhoubinbin@loongson.cn>
 */

#include <linux/bits.h>
#include <linux/completion.h>
#include <linux/device.h>
#include <linux/iopoll.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pm_runtime.h>
#include <linux/platform_device.h>
#include <linux/property.h>
#include <linux/units.h>

/* I2C Registers */
#define I2C_LS2X_PRER		0x0 /* Freq Division Register(16 bits) */
#define I2C_LS2X_CTR		0x2 /* Control Register */
#define I2C_LS2X_TXR		0x3 /* Transport Data Register */
#define I2C_LS2X_RXR		0x3 /* Receive Data Register */
#define I2C_LS2X_CR		0x4 /* Command Control Register */
#define I2C_LS2X_SR		0x4 /* State Register */

/* Command Control Register Bit */
#define LS2X_CR_START		BIT(7) /* Start signal */
#define LS2X_CR_STOP		BIT(6) /* Stop signal */
#define LS2X_CR_READ		BIT(5) /* Read signal */
#define LS2X_CR_WRITE		BIT(4) /* Write signal */
#define LS2X_CR_ACK		BIT(3) /* Response signal */
#define LS2X_CR_IACK		BIT(0) /* Interrupt response signal */

/* State Register Bit */
#define LS2X_SR_NOACK		BIT(7) /* Receive NACK */
#define LS2X_SR_BUSY		BIT(6) /* Bus busy state */
#define LS2X_SR_AL		BIT(5) /* Arbitration lost */
#define LS2X_SR_TIP		BIT(1) /* Transmission state */
#define LS2X_SR_IF		BIT(0) /* Interrupt flag */

/* Control Register Bit */
#define LS2X_CTR_EN		BIT(7) /* 0: I2c frequency setting 1: Normal */
#define LS2X_CTR_IEN		BIT(6) /* Enable i2c interrupt */
#define LS2X_CTR_MST		BIT(5) /* 0: Target mode 1: Controller mode */
#define CTR_FREQ_MASK		GENMASK(7, 6)
#define CTR_READY_MASK		GENMASK(7, 5)

/* The PCLK frequency from LPB */
#define LS2X_I2C_PCLK_FREQ	(50 * HZ_PER_MHZ)

/* The default bus frequency, which is an empirical value */
#define LS2X_I2C_FREQ_STD	(33 * HZ_PER_KHZ)

struct ls2x_i2c_priv {
	struct i2c_adapter	adapter;
	void __iomem		*base;
	struct i2c_timings	i2c_t;
	struct completion	cmd_complete;
};

/*
 * Interrupt service routine.
 * This gets called whenever an I2C interrupt occurs.
 */
static irqreturn_t ls2x_i2c_isr(int this_irq, void *dev_id)
{
	struct ls2x_i2c_priv *priv = dev_id;

	if (!(readb(priv->base + I2C_LS2X_SR) & LS2X_SR_IF))
		return IRQ_NONE;

	writeb(LS2X_CR_IACK, priv->base + I2C_LS2X_CR);
	complete(&priv->cmd_complete);
	return IRQ_HANDLED;
}

/*
 * The ls2x i2c controller supports standard mode and fast mode, so the
 * maximum bus frequency is '400kHz'.
 * The bus frequency is set to the empirical value of '33KHz' by default,
 * but it can also be taken from ACPI or FDT for compatibility with more
 * devices.
 */
static void ls2x_i2c_adjust_bus_speed(struct ls2x_i2c_priv *priv)
{
	struct i2c_timings *t = &priv->i2c_t;
	struct device *dev = priv->adapter.dev.parent;
	u32 acpi_speed = i2c_acpi_find_bus_speed(dev);

	i2c_parse_fw_timings(dev, t, false);

	if (acpi_speed || t->bus_freq_hz)
		t->bus_freq_hz = max(t->bus_freq_hz, acpi_speed);
	else
		t->bus_freq_hz = LS2X_I2C_FREQ_STD;

	/* Calculate and set i2c frequency. */
	writew(LS2X_I2C_PCLK_FREQ / (5 * t->bus_freq_hz) - 1,
	       priv->base + I2C_LS2X_PRER);
}

static void ls2x_i2c_init(struct ls2x_i2c_priv *priv)
{
	/* Set i2c frequency setting mode and disable interrupts. */
	writeb(readb(priv->base + I2C_LS2X_CTR) & ~CTR_FREQ_MASK,
	       priv->base + I2C_LS2X_CTR);

	ls2x_i2c_adjust_bus_speed(priv);

	/* Set i2c normal operating mode and enable interrupts. */
	writeb(readb(priv->base + I2C_LS2X_CTR) | CTR_READY_MASK,
	       priv->base + I2C_LS2X_CTR);
}

static int ls2x_i2c_xfer_byte(struct ls2x_i2c_priv *priv, u8 txdata, u8 *rxdatap)
{
	u8 rxdata;
	unsigned long time_left;

	writeb(txdata, priv->base + I2C_LS2X_CR);

	time_left = wait_for_completion_timeout(&priv->cmd_complete,
						priv->adapter.timeout);
	if (!time_left)
		return -ETIMEDOUT;

	rxdata = readb(priv->base + I2C_LS2X_SR);
	if (rxdatap)
		*rxdatap = rxdata;

	return 0;
}

static int ls2x_i2c_send_byte(struct ls2x_i2c_priv *priv, u8 txdata)
{
	int ret;
	u8 rxdata;

	ret = ls2x_i2c_xfer_byte(priv, txdata, &rxdata);
	if (ret)
		return ret;

	if (rxdata & LS2X_SR_AL)
		return -EAGAIN;

	if (rxdata & LS2X_SR_NOACK)
		return -ENXIO;

	return 0;
}

static int ls2x_i2c_stop(struct ls2x_i2c_priv *priv)
{
	u8 value;

	writeb(LS2X_CR_STOP, priv->base + I2C_LS2X_CR);
	return readb_poll_timeout(priv->base + I2C_LS2X_SR, value,
				  !(value & LS2X_SR_BUSY), 100,
				  jiffies_to_usecs(priv->adapter.timeout));
}

static int ls2x_i2c_start(struct ls2x_i2c_priv *priv, struct i2c_msg *msgs)
{
	reinit_completion(&priv->cmd_complete);

	writeb(i2c_8bit_addr_from_msg(msgs), priv->base + I2C_LS2X_TXR);
	return ls2x_i2c_send_byte(priv, LS2X_CR_START | LS2X_CR_WRITE);
}

static int ls2x_i2c_rx(struct ls2x_i2c_priv *priv, struct i2c_msg *msg)
{
	int ret;
	u8 rxdata, *buf = msg->buf;
	u16 len = msg->len;

	/* Contains steps to send start condition and address. */
	ret = ls2x_i2c_start(priv, msg);
	if (ret)
		return ret;

	while (len--) {
		ret = ls2x_i2c_xfer_byte(priv,
					 LS2X_CR_READ | (len ? 0 : LS2X_CR_ACK),
					 &rxdata);
		if (ret)
			return ret;

		*buf++ = readb(priv->base + I2C_LS2X_RXR);
	}

	return 0;
}

static int ls2x_i2c_tx(struct ls2x_i2c_priv *priv, struct i2c_msg *msg)
{
	int ret;
	u8 *buf = msg->buf;
	u16 len = msg->len;

	/* Contains steps to send start condition and address. */
	ret = ls2x_i2c_start(priv, msg);
	if (ret)
		return ret;

	while (len--) {
		writeb(*buf++, priv->base + I2C_LS2X_TXR);

		ret = ls2x_i2c_send_byte(priv, LS2X_CR_WRITE);
		if (ret)
			return ret;
	}

	return 0;
}

static int ls2x_i2c_xfer_one(struct ls2x_i2c_priv *priv,
			     struct i2c_msg *msg, bool stop)
{
	int ret;

	if (msg->flags & I2C_M_RD)
		ret = ls2x_i2c_rx(priv, msg);
	else
		ret = ls2x_i2c_tx(priv, msg);

	if (ret < 0) {
		/* Fatel error. Needs reinit. */
		if (ret == -ETIMEDOUT)
			ls2x_i2c_init(priv);

		return ret;
	}

	if (stop) {
		/* Failed to issue STOP. Needs reinit. */
		ret = ls2x_i2c_stop(priv);
		if (ret)
			ls2x_i2c_init(priv);
	}

	return ret;
}

static int ls2x_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
{
	int ret;
	struct i2c_msg *msg, *emsg = msgs + num;
	struct ls2x_i2c_priv *priv = i2c_get_adapdata(adap);

	for (msg = msgs; msg < emsg; msg++) {
		ret = ls2x_i2c_xfer_one(priv, msg, msg == emsg - 1);
		if (ret)
			return ret;
	}

	return num;
}

static unsigned int ls2x_i2c_func(struct i2c_adapter *adap)
{
	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
}

static const struct i2c_algorithm ls2x_i2c_algo = {
	.xfer = ls2x_i2c_xfer,
	.functionality = ls2x_i2c_func,
};

static int ls2x_i2c_probe(struct platform_device *pdev)
{
	int ret, irq;
	struct i2c_adapter *adap;
	struct ls2x_i2c_priv *priv;
	struct device *dev = &pdev->dev;

	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
	if (!priv)
		return -ENOMEM;

	/* Map hardware registers */
	priv->base = devm_platform_ioremap_resource(pdev, 0);
	if (IS_ERR(priv->base))
		return PTR_ERR(priv->base);

	irq = platform_get_irq(pdev, 0);
	if (irq < 0)
		return irq;

	/* Add the i2c adapter */
	adap = &priv->adapter;
	adap->retries = 5;
	adap->nr = pdev->id;
	adap->dev.parent = dev;
	adap->owner = THIS_MODULE;
	adap->algo = &ls2x_i2c_algo;
	adap->timeout = msecs_to_jiffies(100);
	device_set_node(&adap->dev, dev_fwnode(dev));
	i2c_set_adapdata(adap, priv);
	strscpy(adap->name, pdev->name, sizeof(adap->name));
	init_completion(&priv->cmd_complete);
	platform_set_drvdata(pdev, priv);

	ls2x_i2c_init(priv);

	ret = devm_request_irq(dev, irq, ls2x_i2c_isr, IRQF_SHARED, "ls2x-i2c",
			       priv);
	if (ret < 0)
		return dev_err_probe(dev, ret, "Unable to request irq %d\n", irq);

	return devm_i2c_add_adapter(dev, adap);
}

static int ls2x_i2c_suspend(struct device *dev)
{
	struct ls2x_i2c_priv *priv = dev_get_drvdata(dev);

	/* Disable interrupts */
	writeb(readb(priv->base + I2C_LS2X_CTR) & ~LS2X_CTR_IEN,
	       priv->base + I2C_LS2X_CTR);

	return 0;
}

static int ls2x_i2c_resume(struct device *dev)
{
	ls2x_i2c_init(dev_get_drvdata(dev));
	return 0;
}

static DEFINE_RUNTIME_DEV_PM_OPS(ls2x_i2c_pm_ops,
				 ls2x_i2c_suspend, ls2x_i2c_resume, NULL);

static const struct of_device_id ls2x_i2c_id_table[] = {
	{ .compatible = "loongson,ls2k-i2c" },
	{ .compatible = "loongson,ls7a-i2c" },
	{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, ls2x_i2c_id_table);

static const struct acpi_device_id ls2x_i2c_acpi_match[] = {
	{ "LOON0004" }, /* Loongson LS7A */
	{ }
};
MODULE_DEVICE_TABLE(acpi, ls2x_i2c_acpi_match);

static struct platform_driver ls2x_i2c_driver = {
	.probe		= ls2x_i2c_probe,
	.driver		= {
		.name	= "ls2x-i2c",
		.pm	= pm_sleep_ptr(&ls2x_i2c_pm_ops),
		.of_match_table = ls2x_i2c_id_table,
		.acpi_match_table = ls2x_i2c_acpi_match,
	},
};
module_platform_driver(ls2x_i2c_driver);

MODULE_DESCRIPTION("Loongson LS2X I2C Bus driver");
MODULE_AUTHOR("Loongson Technology Corporation Limited");
MODULE_LICENSE("GPL");