Merge tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX fixes for 3.7-rc
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: ehci: fix host power mask bit
ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile
index f2aa09e..9137df5 100644
--- a/arch/arm/boot/Makefile
+++ b/arch/arm/boot/Makefile
@@ -33,7 +33,7 @@
$(obj)/xipImage: vmlinux FORCE
$(call if_changed,objcopy)
- $(kecho) ' Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
+ @$(kecho) ' Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
$(obj)/Image $(obj)/zImage: FORCE
@echo 'Kernel configured for XIP (CONFIG_XIP_KERNEL=y)'
@@ -48,14 +48,14 @@
$(obj)/Image: vmlinux FORCE
$(call if_changed,objcopy)
- $(kecho) ' Kernel: $@ is ready'
+ @$(kecho) ' Kernel: $@ is ready'
$(obj)/compressed/vmlinux: $(obj)/Image FORCE
$(Q)$(MAKE) $(build)=$(obj)/compressed $@
$(obj)/zImage: $(obj)/compressed/vmlinux FORCE
$(call if_changed,objcopy)
- $(kecho) ' Kernel: $@ is ready'
+ @$(kecho) ' Kernel: $@ is ready'
endif
@@ -90,7 +90,7 @@
$(obj)/uImage: $(obj)/zImage FORCE
@$(check_for_multiple_loadaddr)
$(call if_changed,uimage)
- $(kecho) ' Image $@ is ready'
+ @$(kecho) ' Image $@ is ready'
$(obj)/bootp/bootp: $(obj)/zImage initrd FORCE
$(Q)$(MAKE) $(build)=$(obj)/bootp $@
@@ -98,7 +98,7 @@
$(obj)/bootpImage: $(obj)/bootp/bootp FORCE
$(call if_changed,objcopy)
- $(kecho) ' Kernel: $@ is ready'
+ @$(kecho) ' Kernel: $@ is ready'
PHONY += initrd FORCE
initrd:
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index b1497c7..df7f227 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -73,8 +73,8 @@
pinmux: pinmux {
compatible = "nvidia,tegra30-pinmux";
- reg = <0x70000868 0xd0 /* Pad control registers */
- 0x70003000 0x3e0>; /* Mux registers */
+ reg = <0x70000868 0xd4 /* Pad control registers */
+ 0x70003000 0x3e4>; /* Mux registers */
};
serial@70006000 {
diff --git a/arch/arm/mach-highbank/system.c b/arch/arm/mach-highbank/system.c
index 82c27230..86e37cd 100644
--- a/arch/arm/mach-highbank/system.c
+++ b/arch/arm/mach-highbank/system.c
@@ -28,6 +28,7 @@
hignbank_set_pwr_soft_reset();
scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
- cpu_do_idle();
+ while (1)
+ cpu_do_idle();
}
diff --git a/arch/arm/mach-omap2/clockdomains44xx_data.c b/arch/arm/mach-omap2/clockdomains44xx_data.c
index b56d06b..95192a06 100644
--- a/arch/arm/mach-omap2/clockdomains44xx_data.c
+++ b/arch/arm/mach-omap2/clockdomains44xx_data.c
@@ -359,7 +359,7 @@
.clkdm_offs = OMAP4430_CM2_CAM_CAM_CDOFFS,
.wkdep_srcs = iss_wkup_sleep_deps,
.sleepdep_srcs = iss_wkup_sleep_deps,
- .flags = CLKDM_CAN_HWSUP_SWSUP,
+ .flags = CLKDM_CAN_SWSUP,
};
static struct clockdomain l3_dss_44xx_clkdm = {
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index cba60e05..c72b5a7 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -19,6 +19,7 @@
#include <linux/of.h>
#include <linux/pinctrl/machine.h>
#include <linux/platform_data/omap4-keypad.h>
+#include <linux/platform_data/omap_ocp2scp.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
@@ -613,6 +614,83 @@
static inline void omap_init_vout(void) {}
#endif
+#if defined(CONFIG_OMAP_OCP2SCP) || defined(CONFIG_OMAP_OCP2SCP_MODULE)
+static int count_ocp2scp_devices(struct omap_ocp2scp_dev *ocp2scp_dev)
+{
+ int cnt = 0;
+
+ while (ocp2scp_dev->drv_name != NULL) {
+ cnt++;
+ ocp2scp_dev++;
+ }
+
+ return cnt;
+}
+
+static void omap_init_ocp2scp(void)
+{
+ struct omap_hwmod *oh;
+ struct platform_device *pdev;
+ int bus_id = -1, dev_cnt = 0, i;
+ struct omap_ocp2scp_dev *ocp2scp_dev;
+ const char *oh_name, *name;
+ struct omap_ocp2scp_platform_data *pdata;
+
+ if (!cpu_is_omap44xx())
+ return;
+
+ oh_name = "ocp2scp_usb_phy";
+ name = "omap-ocp2scp";
+
+ oh = omap_hwmod_lookup(oh_name);
+ if (!oh) {
+ pr_err("%s: could not find omap_hwmod for %s\n", __func__,
+ oh_name);
+ return;
+ }
+
+ pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
+ if (!pdata) {
+ pr_err("%s: No memory for ocp2scp pdata\n", __func__);
+ return;
+ }
+
+ ocp2scp_dev = oh->dev_attr;
+ dev_cnt = count_ocp2scp_devices(ocp2scp_dev);
+
+ if (!dev_cnt) {
+ pr_err("%s: No devices connected to ocp2scp\n", __func__);
+ kfree(pdata);
+ return;
+ }
+
+ pdata->devices = kzalloc(sizeof(struct omap_ocp2scp_dev *)
+ * dev_cnt, GFP_KERNEL);
+ if (!pdata->devices) {
+ pr_err("%s: No memory for ocp2scp pdata devices\n", __func__);
+ kfree(pdata);
+ return;
+ }
+
+ for (i = 0; i < dev_cnt; i++, ocp2scp_dev++)
+ pdata->devices[i] = ocp2scp_dev;
+
+ pdata->dev_cnt = dev_cnt;
+
+ pdev = omap_device_build(name, bus_id, oh, pdata, sizeof(*pdata), NULL,
+ 0, false);
+ if (IS_ERR(pdev)) {
+ pr_err("Could not build omap_device for %s %s\n",
+ name, oh_name);
+ kfree(pdata->devices);
+ kfree(pdata);
+ return;
+ }
+}
+#else
+static inline void omap_init_ocp2scp(void) { }
+#endif
+
/*-------------------------------------------------------------------------*/
static int __init omap2_init_devices(void)
@@ -640,6 +718,7 @@
omap_init_sham();
omap_init_aes();
omap_init_vout();
+ omap_init_ocp2scp();
return 0;
}
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index b969ab1..87cc6d0 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -422,6 +422,38 @@
}
/**
+ * _wait_softreset_complete - wait for an OCP softreset to complete
+ * @oh: struct omap_hwmod * to wait on
+ *
+ * Wait until the IP block represented by @oh reports that its OCP
+ * softreset is complete. This can be triggered by software (see
+ * _ocp_softreset()) or by hardware upon returning from off-mode (one
+ * example is HSMMC). Waits for up to MAX_MODULE_SOFTRESET_WAIT
+ * microseconds. Returns the number of microseconds waited.
+ */
+static int _wait_softreset_complete(struct omap_hwmod *oh)
+{
+ struct omap_hwmod_class_sysconfig *sysc;
+ u32 softrst_mask;
+ int c = 0;
+
+ sysc = oh->class->sysc;
+
+ if (sysc->sysc_flags & SYSS_HAS_RESET_STATUS)
+ omap_test_timeout((omap_hwmod_read(oh, sysc->syss_offs)
+ & SYSS_RESETDONE_MASK),
+ MAX_MODULE_SOFTRESET_WAIT, c);
+ else if (sysc->sysc_flags & SYSC_HAS_RESET_STATUS) {
+ softrst_mask = (0x1 << sysc->sysc_fields->srst_shift);
+ omap_test_timeout(!(omap_hwmod_read(oh, sysc->sysc_offs)
+ & softrst_mask),
+ MAX_MODULE_SOFTRESET_WAIT, c);
+ }
+
+ return c;
+}
+
+/**
* _set_dmadisable: set OCP_SYSCONFIG.DMADISABLE bit in @v
* @oh: struct omap_hwmod *
*
@@ -1282,6 +1314,18 @@
if (!oh->class->sysc)
return;
+ /*
+ * Wait until reset has completed, this is needed as the IP
+ * block is reset automatically by hardware in some cases
+ * (off-mode for example), and the drivers require the
+ * IP to be ready when they access it
+ */
+ if (oh->flags & HWMOD_CONTROL_OPT_CLKS_IN_RESET)
+ _enable_optional_clocks(oh);
+ _wait_softreset_complete(oh);
+ if (oh->flags & HWMOD_CONTROL_OPT_CLKS_IN_RESET)
+ _disable_optional_clocks(oh);
+
v = oh->_sysc_cache;
sf = oh->class->sysc->sysc_flags;
@@ -1804,7 +1848,7 @@
*/
static int _ocp_softreset(struct omap_hwmod *oh)
{
- u32 v, softrst_mask;
+ u32 v;
int c = 0;
int ret = 0;
@@ -1834,19 +1878,7 @@
if (oh->class->sysc->srst_udelay)
udelay(oh->class->sysc->srst_udelay);
- if (oh->class->sysc->sysc_flags & SYSS_HAS_RESET_STATUS)
- omap_test_timeout((omap_hwmod_read(oh,
- oh->class->sysc->syss_offs)
- & SYSS_RESETDONE_MASK),
- MAX_MODULE_SOFTRESET_WAIT, c);
- else if (oh->class->sysc->sysc_flags & SYSC_HAS_RESET_STATUS) {
- softrst_mask = (0x1 << oh->class->sysc->sysc_fields->srst_shift);
- omap_test_timeout(!(omap_hwmod_read(oh,
- oh->class->sysc->sysc_offs)
- & softrst_mask),
- MAX_MODULE_SOFTRESET_WAIT, c);
- }
-
+ c = _wait_softreset_complete(oh);
if (c == MAX_MODULE_SOFTRESET_WAIT)
pr_warning("omap_hwmod: %s: softreset failed (waited %d usec)\n",
oh->name, MAX_MODULE_SOFTRESET_WAIT);
@@ -2352,6 +2384,9 @@
if (oh->_state != _HWMOD_STATE_INITIALIZED)
return -EINVAL;
+ if (oh->flags & HWMOD_EXT_OPT_MAIN_CLK)
+ return -EPERM;
+
if (oh->rst_lines_cnt == 0) {
r = _enable(oh);
if (r) {
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index 652d028..0b1249e 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -21,6 +21,7 @@
#include <linux/io.h>
#include <linux/platform_data/gpio-omap.h>
#include <linux/power/smartreflex.h>
+#include <linux/platform_data/omap_ocp2scp.h>
#include <plat/omap_hwmod.h>
#include <plat/i2c.h>
@@ -2125,6 +2126,14 @@
.name = "mcpdm",
.class = &omap44xx_mcpdm_hwmod_class,
.clkdm_name = "abe_clkdm",
+ /*
+ * It's suspected that the McPDM requires an off-chip main
+ * functional clock, controlled via I2C. This IP block is
+ * currently reset very early during boot, before I2C is
+ * available, so it doesn't seem that we have any choice in
+ * the kernel other than to avoid resetting it.
+ */
+ .flags = HWMOD_EXT_OPT_MAIN_CLK,
.mpu_irqs = omap44xx_mcpdm_irqs,
.sdma_reqs = omap44xx_mcpdm_sdma_reqs,
.main_clk = "mcpdm_fck",
@@ -2681,6 +2690,32 @@
.sysc = &omap44xx_ocp2scp_sysc,
};
+/* ocp2scp dev_attr */
+static struct resource omap44xx_usb_phy_and_pll_addrs[] = {
+ {
+ .name = "usb_phy",
+ .start = 0x4a0ad080,
+ .end = 0x4a0ae000,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ /* XXX: Remove this once control module driver is in place */
+ .name = "ctrl_dev",
+ .start = 0x4a002300,
+ .end = 0x4a002303,
+ .flags = IORESOURCE_MEM,
+ },
+ { }
+};
+
+static struct omap_ocp2scp_dev ocp2scp_dev_attr[] = {
+ {
+ .drv_name = "omap-usb2",
+ .res = omap44xx_usb_phy_and_pll_addrs,
+ },
+ { }
+};
+
/* ocp2scp_usb_phy */
static struct omap_hwmod omap44xx_ocp2scp_usb_phy_hwmod = {
.name = "ocp2scp_usb_phy",
@@ -2694,6 +2729,7 @@
.modulemode = MODULEMODE_HWCTRL,
},
},
+ .dev_attr = ocp2scp_dev_attr,
};
/*
diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c
index 635e109..44c4205 100644
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -366,7 +366,7 @@
};
static struct regulator_consumer_supply omap4_vdd1_supply[] = {
- REGULATOR_SUPPLY("vcc", "mpu.0"),
+ REGULATOR_SUPPLY("vcc", "cpu0"),
};
static struct regulator_consumer_supply omap4_vdd2_supply[] = {
diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c
index 880249b..75878c3 100644
--- a/arch/arm/mach-omap2/vc.c
+++ b/arch/arm/mach-omap2/vc.c
@@ -264,7 +264,7 @@
if (initialized) {
if (voltdm->pmic->i2c_high_speed != i2c_high_speed)
- pr_warn("%s: I2C config for vdd_%s does not match other channels (%u).",
+ pr_warn("%s: I2C config for vdd_%s does not match other channels (%u).\n",
__func__, voltdm->name, i2c_high_speed);
return;
}
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index 5ecbd17..e2c6391 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -28,6 +28,7 @@
#include <linux/mfd/asic3.h>
#include <linux/mtd/physmap.h>
#include <linux/pda_power.h>
+#include <linux/pwm.h>
#include <linux/pwm_backlight.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/gpio-regulator.h>
@@ -556,7 +557,7 @@
*/
static struct platform_pwm_backlight_data backlight_data = {
- .pwm_id = 1,
+ .pwm_id = -1, /* Superseded by pwm_lookup */
.max_brightness = 200,
.dft_brightness = 100,
.pwm_period_ns = 30923,
@@ -571,6 +572,10 @@
},
};
+static struct pwm_lookup hx4700_pwm_lookup[] = {
+ PWM_LOOKUP("pxa27x-pwm.1", 0, "pwm-backlight", NULL),
+};
+
/*
* USB "Transceiver"
*/
@@ -872,6 +877,7 @@
pxa_set_stuart_info(NULL);
platform_add_devices(devices, ARRAY_SIZE(devices));
+ pwm_add_table(hx4700_pwm_lookup, ARRAY_SIZE(hx4700_pwm_lookup));
pxa_set_ficp_info(&ficp_info);
pxa27x_set_i2c_power_info(NULL);
diff --git a/arch/arm/mach-pxa/spitz_pm.c b/arch/arm/mach-pxa/spitz_pm.c
index 438f02f..842596d 100644
--- a/arch/arm/mach-pxa/spitz_pm.c
+++ b/arch/arm/mach-pxa/spitz_pm.c
@@ -86,10 +86,7 @@
gpio_set_value(SPITZ_GPIO_LED_GREEN, on);
}
-static unsigned long gpio18_config[] = {
- GPIO18_RDY,
- GPIO18_GPIO,
-};
+static unsigned long gpio18_config = GPIO18_GPIO;
static void spitz_presuspend(void)
{
@@ -112,7 +109,7 @@
PGSR3 &= ~SPITZ_GPIO_G3_STROBE_BIT;
PGSR2 |= GPIO_bit(SPITZ_GPIO_KEY_STROBE0);
- pxa2xx_mfp_config(&gpio18_config[0], 1);
+ pxa2xx_mfp_config(&gpio18_config, 1);
gpio_request_one(18, GPIOF_OUT_INIT_HIGH, "Unknown");
gpio_free(18);
@@ -131,7 +128,6 @@
static void spitz_postsuspend(void)
{
- pxa2xx_mfp_config(&gpio18_config[1], 1);
}
static int spitz_should_wakeup(unsigned int resume_on_alarm)
diff --git a/arch/arm/plat-omap/include/plat/omap_hwmod.h b/arch/arm/plat-omap/include/plat/omap_hwmod.h
index b3349f7..1db0294 100644
--- a/arch/arm/plat-omap/include/plat/omap_hwmod.h
+++ b/arch/arm/plat-omap/include/plat/omap_hwmod.h
@@ -443,6 +443,11 @@
* in order to complete the reset. Optional clocks will be disabled
* again after the reset.
* HWMOD_16BIT_REG: Module has 16bit registers
+ * HWMOD_EXT_OPT_MAIN_CLK: The only main functional clock source for
+ * this IP block comes from an off-chip source and is not always
+ * enabled. This prevents the hwmod code from being able to
+ * enable and reset the IP block early. XXX Eventually it should
+ * be possible to query the clock framework for this information.
*/
#define HWMOD_SWSUP_SIDLE (1 << 0)
#define HWMOD_SWSUP_MSTANDBY (1 << 1)
@@ -453,6 +458,7 @@
#define HWMOD_NO_IDLEST (1 << 6)
#define HWMOD_CONTROL_OPT_CLKS_IN_RESET (1 << 7)
#define HWMOD_16BIT_REG (1 << 8)
+#define HWMOD_EXT_OPT_MAIN_CLK (1 << 9)
/*
* omap_hwmod._int_flags definitions
diff --git a/arch/arm/tools/Makefile b/arch/arm/tools/Makefile
index cd60a811..32d05c8 100644
--- a/arch/arm/tools/Makefile
+++ b/arch/arm/tools/Makefile
@@ -5,6 +5,6 @@
#
include/generated/mach-types.h: $(src)/gen-mach-types $(src)/mach-types
- $(kecho) ' Generating $@'
+ @$(kecho) ' Generating $@'
@mkdir -p $(dir $@)
$(Q)$(AWK) -f $^ > $@ || { rm -f $@; /bin/false; }
diff --git a/drivers/bus/omap-ocp2scp.c b/drivers/bus/omap-ocp2scp.c
index ff63560..0c48b0e 100644
--- a/drivers/bus/omap-ocp2scp.c
+++ b/drivers/bus/omap-ocp2scp.c
@@ -22,6 +22,26 @@
#include <linux/pm_runtime.h>
#include <linux/of.h>
#include <linux/of_platform.h>
+#include <linux/platform_data/omap_ocp2scp.h>
+
+/**
+ * _count_resources - count for the number of resources
+ * @res: struct resource *
+ *
+ * Count and return the number of resources populated for the device that is
+ * connected to ocp2scp.
+ */
+static unsigned _count_resources(struct resource *res)
+{
+ int cnt = 0;
+
+ while (res->start != res->end) {
+ cnt++;
+ res++;
+ }
+
+ return cnt;
+}
static int ocp2scp_remove_devices(struct device *dev, void *c)
{
@@ -34,20 +54,62 @@
static int __devinit omap_ocp2scp_probe(struct platform_device *pdev)
{
- int ret;
- struct device_node *np = pdev->dev.of_node;
+ int ret;
+ unsigned res_cnt, i;
+ struct device_node *np = pdev->dev.of_node;
+ struct platform_device *pdev_child;
+ struct omap_ocp2scp_platform_data *pdata = pdev->dev.platform_data;
+ struct omap_ocp2scp_dev *dev;
if (np) {
ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
if (ret) {
- dev_err(&pdev->dev, "failed to add resources for ocp2scp child\n");
+ dev_err(&pdev->dev,
+ "failed to add resources for ocp2scp child\n");
goto err0;
}
+ } else if (pdata) {
+ for (i = 0, dev = *pdata->devices; i < pdata->dev_cnt; i++,
+ dev++) {
+ res_cnt = _count_resources(dev->res);
+
+ pdev_child = platform_device_alloc(dev->drv_name,
+ PLATFORM_DEVID_AUTO);
+ if (!pdev_child) {
+ dev_err(&pdev->dev,
+ "failed to allocate mem for ocp2scp child\n");
+ goto err0;
+ }
+
+ ret = platform_device_add_resources(pdev_child,
+ dev->res, res_cnt);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "failed to add resources for ocp2scp child\n");
+ goto err1;
+ }
+
+ pdev_child->dev.parent = &pdev->dev;
+
+ ret = platform_device_add(pdev_child);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "failed to register ocp2scp child device\n");
+ goto err1;
+ }
+ }
+ } else {
+ dev_err(&pdev->dev, "OCP2SCP initialized without plat data\n");
+ return -EINVAL;
}
+
pm_runtime_enable(&pdev->dev);
return 0;
+err1:
+ platform_device_put(pdev_child);
+
err0:
device_for_each_child(&pdev->dev, NULL, ocp2scp_remove_devices);
diff --git a/drivers/irqchip/irq-bcm2835.c b/drivers/irqchip/irq-bcm2835.c
index dc670cc..16c78f1 100644
--- a/drivers/irqchip/irq-bcm2835.c
+++ b/drivers/irqchip/irq-bcm2835.c
@@ -168,7 +168,8 @@
}
static struct of_device_id irq_of_match[] __initconst = {
- { .compatible = "brcm,bcm2835-armctrl-ic", .data = armctrl_of_init }
+ { .compatible = "brcm,bcm2835-armctrl-ic", .data = armctrl_of_init },
+ { }
};
void __init bcm2835_init_irq(void)
diff --git a/include/linux/platform_data/omap_ocp2scp.h b/include/linux/platform_data/omap_ocp2scp.h
new file mode 100644
index 0000000..5c6c393
--- /dev/null
+++ b/include/linux/platform_data/omap_ocp2scp.h
@@ -0,0 +1,31 @@
+/*
+ * omap_ocp2scp.h -- ocp2scp header file
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __DRIVERS_OMAP_OCP2SCP_H
+#define __DRIVERS_OMAP_OCP2SCP_H
+
+struct omap_ocp2scp_dev {
+ const char *drv_name;
+ struct resource *res;
+};
+
+struct omap_ocp2scp_platform_data {
+ int dev_cnt;
+ struct omap_ocp2scp_dev **devices;
+};
+#endif /* __DRIVERS_OMAP_OCP2SCP_H */
