diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile
index 5140df5f..39c9834 100644
--- a/arch/arm/kernel/Makefile
+++ b/arch/arm/kernel/Makefile
@@ -17,7 +17,8 @@
 
 obj-y		:= elf.o entry-common.o irq.o opcodes.o \
 		   process.o ptrace.o return_address.o \
-		   setup.o signal.o stacktrace.o sys_arm.o time.o traps.o
+		   setup.o signal.o sigreturn_codes.o \
+		   stacktrace.o sys_arm.o time.o traps.o
 
 obj-$(CONFIG_ATAGS)		+= atags_parse.o
 obj-$(CONFIG_ATAGS_PROC)	+= atags_proc.o
diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c
index ab33042..64845fc 100644
--- a/arch/arm/kernel/signal.c
+++ b/arch/arm/kernel/signal.c
@@ -21,29 +21,7 @@
 #include <asm/unistd.h>
 #include <asm/vfp.h>
 
-/*
- * For ARM syscalls, we encode the syscall number into the instruction.
- */
-#define SWI_SYS_SIGRETURN	(0xef000000|(__NR_sigreturn)|(__NR_OABI_SYSCALL_BASE))
-#define SWI_SYS_RT_SIGRETURN	(0xef000000|(__NR_rt_sigreturn)|(__NR_OABI_SYSCALL_BASE))
-
-/*
- * With EABI, the syscall number has to be loaded into r7.
- */
-#define MOV_R7_NR_SIGRETURN	(0xe3a07000 | (__NR_sigreturn - __NR_SYSCALL_BASE))
-#define MOV_R7_NR_RT_SIGRETURN	(0xe3a07000 | (__NR_rt_sigreturn - __NR_SYSCALL_BASE))
-
-/*
- * For Thumb syscalls, we pass the syscall number via r7.  We therefore
- * need two 16-bit instructions.
- */
-#define SWI_THUMB_SIGRETURN	(0xdf00 << 16 | 0x2700 | (__NR_sigreturn - __NR_SYSCALL_BASE))
-#define SWI_THUMB_RT_SIGRETURN	(0xdf00 << 16 | 0x2700 | (__NR_rt_sigreturn - __NR_SYSCALL_BASE))
-
-static const unsigned long sigreturn_codes[7] = {
-	MOV_R7_NR_SIGRETURN,    SWI_SYS_SIGRETURN,    SWI_THUMB_SIGRETURN,
-	MOV_R7_NR_RT_SIGRETURN, SWI_SYS_RT_SIGRETURN, SWI_THUMB_RT_SIGRETURN,
-};
+extern const unsigned long sigreturn_codes[7];
 
 static unsigned long signal_return_offset;
 
diff --git a/arch/arm/kernel/sigreturn_codes.S b/arch/arm/kernel/sigreturn_codes.S
new file mode 100644
index 0000000..3c5d0f2
--- /dev/null
+++ b/arch/arm/kernel/sigreturn_codes.S
@@ -0,0 +1,80 @@
+/*
+ * sigreturn_codes.S - code sinpets for sigreturn syscalls
+ *
+ * Created by:	Victor Kamensky, 2013-08-13
+ * Copyright:	(C) 2013  Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <asm/unistd.h>
+
+/*
+ * For ARM syscalls, we encode the syscall number into the instruction.
+ * With EABI, the syscall number has to be loaded into r7. As result
+ * ARM syscall sequence snippet will have move and svc in .arm encoding
+ *
+ * For Thumb syscalls, we pass the syscall number via r7.  We therefore
+ * need two 16-bit instructions in .thumb encoding
+ *
+ * Please note sigreturn_codes code are not executed in place. Instead
+ * they just copied by kernel into appropriate places. Code inside of
+ * arch/arm/kernel/signal.c is very sensitive to layout of these code
+ * snippets.
+ */
+
+#if __LINUX_ARM_ARCH__ <= 4
+	/*
+	 * Note we manually set minimally required arch that supports
+	 * required thumb opcodes for early arch versions. It is OK
+	 * for this file to be used in combination with other
+	 * lower arch variants, since these code snippets are only
+	 * used as input data.
+	 */
+	.arch armv4t
+#endif
+
+	.section .rodata
+	.global sigreturn_codes
+	.type	sigreturn_codes, #object
+
+	.arm
+
+sigreturn_codes:
+
+	/* ARM sigreturn syscall code snippet */
+	mov	r7, #(__NR_sigreturn - __NR_SYSCALL_BASE)
+	swi	#(__NR_sigreturn)|(__NR_OABI_SYSCALL_BASE)
+
+	/* Thumb sigreturn syscall code snippet */
+	.thumb
+	movs	r7, #(__NR_sigreturn - __NR_SYSCALL_BASE)
+	swi	#0
+
+	/* ARM sigreturn_rt syscall code snippet */
+	.arm
+	mov	r7, #(__NR_rt_sigreturn - __NR_SYSCALL_BASE)
+	swi	#(__NR_rt_sigreturn)|(__NR_OABI_SYSCALL_BASE)
+
+	/* Thumb sigreturn_rt syscall code snippet */
+	.thumb
+	movs	r7, #(__NR_rt_sigreturn - __NR_SYSCALL_BASE)
+	swi	#0
+
+	/*
+	 * Note on addtional space: setup_return in signal.c
+	 * algorithm uses two words copy regardless whether
+	 * it is thumb case or not, so we need additional
+	 * word after real last entry.
+	 */
+	.arm
+	.space	4
+
+	.size	sigreturn_codes, . - sigreturn_codes