drm/i915/bxt: add display initialize/uninitialize sequence (PHY)
Add PHY specific display initialization sequence as per BSpec.
Note that the PHY initialization/uninitialization are done
at their current place only for simplicity, in a future patch - when more
of the runtime PM features will be enabled - these will be moved to
power well#1 and modeset encoder enabling/disabling hooks respectively.
The call to uninitialize the PHY during system/runtime suspend will be
added later in this patchset.
v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set
v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- fix DDI PHY timeout value
- squash in Vandana's "PORT_CL2CM_DW6_A BUN fix",
"DDI PHY programming register defn", "Do ddi_phy_init always",
- move PHY register macros next to the corresponding CHV/VLV macros
- move DE PLL register macros here from another patch since they are
used here first
- add BXT_ prefix to CDCLK flags
- s/COMMON_RESET/COMMON_RESET_DIS/ and clarify related code comments
- fix incorrect read value for the RMW of BXT_PHY_CTL_FAMILY_DDI
- fix using GT_DISPLAY_EDP_POWER_ON vs. GT_DISPLAY_DDI_POWER_ON
when powering on DDI ports
- fix incorrect port when setting BXT_PORT_TX_DW14_LN for DDI ports
- add missing masking when programming CDCLK_FREQ_DECIMAL
- add missing powering on for DDI-C port, rename OCL2_LDOFUSE_PWR_EN
to OCL2_LDOFUSE_PWR_DIS to reduce confusion
- add note about mismatch with bspec in the PORT_REF_DW6 fields
- factor out PHY init code to a new function, so we can call it for
PHY1 and PHY0, instead of open-coding the same
v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
accordingly
- use the existing dpio_phy enum instead of adding a new one for the
same purpose
- flip the meaning of PHYs so that PHY_A is PHY1 and PHY_BC is PHY0 to
better match CHV
- s/BXT_PHY/_BXT_PHY/
- use _PIPE for _BXT_PHY instead of open-coding it
- drop _0_2_0_GTTMMADR suffix from BXT_P_CR_GT_DISP_PWRON
- define GT_DISPLAY_POWER_ON in a more standard way
- make a note that the CHV ConfigDB also disagrees about GRC_CODE field
definitions
- fix lane optimization refactoring fumble from v3
- add per PHY uninit functions to match the init counterparts
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 164350c..6e0913d 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -1117,6 +1117,102 @@
#define DPIO_FRC_LATENCY_SHFIT 8
#define CHV_TX_DW14(ch, lane) _TXLANE(ch, lane, 0xb8)
#define DPIO_UPAR_SHIFT 30
+
+/* BXT PHY registers */
+#define _BXT_PHY(phy, a, b) _PIPE((phy), (a), (b))
+
+#define BXT_P_CR_GT_DISP_PWRON 0x138090
+#define GT_DISPLAY_POWER_ON(phy) (1 << (phy))
+
+#define _PHY_CTL_FAMILY_EDP 0x64C80
+#define _PHY_CTL_FAMILY_DDI 0x64C90
+#define COMMON_RESET_DIS (1 << 31)
+#define BXT_PHY_CTL_FAMILY(phy) _BXT_PHY((phy), _PHY_CTL_FAMILY_DDI, \
+ _PHY_CTL_FAMILY_EDP)
+
+/* BXT PHY common lane registers */
+#define _PORT_CL1CM_DW0_A 0x162000
+#define _PORT_CL1CM_DW0_BC 0x6C000
+#define PHY_POWER_GOOD (1 << 16)
+#define BXT_PORT_CL1CM_DW0(phy) _BXT_PHY((phy), _PORT_CL1CM_DW0_BC, \
+ _PORT_CL1CM_DW0_A)
+
+#define _PORT_CL1CM_DW9_A 0x162024
+#define _PORT_CL1CM_DW9_BC 0x6C024
+#define IREF0RC_OFFSET_SHIFT 8
+#define IREF0RC_OFFSET_MASK (0xFF << IREF0RC_OFFSET_SHIFT)
+#define BXT_PORT_CL1CM_DW9(phy) _BXT_PHY((phy), _PORT_CL1CM_DW9_BC, \
+ _PORT_CL1CM_DW9_A)
+
+#define _PORT_CL1CM_DW10_A 0x162028
+#define _PORT_CL1CM_DW10_BC 0x6C028
+#define IREF1RC_OFFSET_SHIFT 8
+#define IREF1RC_OFFSET_MASK (0xFF << IREF1RC_OFFSET_SHIFT)
+#define BXT_PORT_CL1CM_DW10(phy) _BXT_PHY((phy), _PORT_CL1CM_DW10_BC, \
+ _PORT_CL1CM_DW10_A)
+
+#define _PORT_CL1CM_DW28_A 0x162070
+#define _PORT_CL1CM_DW28_BC 0x6C070
+#define OCL1_POWER_DOWN_EN (1 << 23)
+#define DW28_OLDO_DYN_PWR_DOWN_EN (1 << 22)
+#define SUS_CLK_CONFIG 0x3
+#define BXT_PORT_CL1CM_DW28(phy) _BXT_PHY((phy), _PORT_CL1CM_DW28_BC, \
+ _PORT_CL1CM_DW28_A)
+
+#define _PORT_CL1CM_DW30_A 0x162078
+#define _PORT_CL1CM_DW30_BC 0x6C078
+#define OCL2_LDOFUSE_PWR_DIS (1 << 6)
+#define BXT_PORT_CL1CM_DW30(phy) _BXT_PHY((phy), _PORT_CL1CM_DW30_BC, \
+ _PORT_CL1CM_DW30_A)
+
+/* Defined for PHY0 only */
+#define BXT_PORT_CL2CM_DW6_BC 0x6C358
+#define DW6_OLDO_DYN_PWR_DOWN_EN (1 << 28)
+
+/* BXT PHY Ref registers */
+#define _PORT_REF_DW3_A 0x16218C
+#define _PORT_REF_DW3_BC 0x6C18C
+#define GRC_DONE (1 << 22)
+#define BXT_PORT_REF_DW3(phy) _BXT_PHY((phy), _PORT_REF_DW3_BC, \
+ _PORT_REF_DW3_A)
+
+#define _PORT_REF_DW6_A 0x162198
+#define _PORT_REF_DW6_BC 0x6C198
+/*
+ * FIXME: BSpec/CHV ConfigDB disagrees on the following two fields, fix them
+ * after testing.
+ */
+#define GRC_CODE_SHIFT 23
+#define GRC_CODE_MASK (0x1FF << GRC_CODE_SHIFT)
+#define GRC_CODE_FAST_SHIFT 16
+#define GRC_CODE_FAST_MASK (0x7F << GRC_CODE_FAST_SHIFT)
+#define GRC_CODE_SLOW_SHIFT 8
+#define GRC_CODE_SLOW_MASK (0xFF << GRC_CODE_SLOW_SHIFT)
+#define GRC_CODE_NOM_MASK 0xFF
+#define BXT_PORT_REF_DW6(phy) _BXT_PHY((phy), _PORT_REF_DW6_BC, \
+ _PORT_REF_DW6_A)
+
+#define _PORT_REF_DW8_A 0x1621A0
+#define _PORT_REF_DW8_BC 0x6C1A0
+#define GRC_DIS (1 << 15)
+#define GRC_RDY_OVRD (1 << 1)
+#define BXT_PORT_REF_DW8(phy) _BXT_PHY((phy), _PORT_REF_DW8_BC, \
+ _PORT_REF_DW8_A)
+
+/* BXT PHY TX registers */
+#define _BXT_LANE_OFFSET(lane) (((lane) >> 1) * 0x200 + \
+ ((lane) & 1) * 0x80)
+
+#define _PORT_TX_DW14_LN0_A 0x162538
+#define _PORT_TX_DW14_LN0_B 0x6C538
+#define _PORT_TX_DW14_LN0_C 0x6C938
+#define LATENCY_OPTIM_SHIFT 30
+#define LATENCY_OPTIM (1 << LATENCY_OPTIM_SHIFT)
+#define BXT_PORT_TX_DW14_LN(port, lane) (_PORT3((port), _PORT_TX_DW14_LN0_A, \
+ _PORT_TX_DW14_LN0_B, \
+ _PORT_TX_DW14_LN0_C) + \
+ _BXT_LANE_OFFSET(lane))
+
/*
* Fence registers
*/
