USB: xhci: Make TRB completion code comparison readable.
Use trb_comp_code instead of getting the completion code from the transfer
event every time.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 35374dd..e876fd3 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -874,6 +874,7 @@
struct urb *urb = 0;
int status = -EINPROGRESS;
struct xhci_ep_ctx *ep_ctx;
+ u32 trb_comp_code;
xhci_dbg(xhci, "In %s\n", __func__);
slot_id = TRB_TO_SLOT_ID(event->flags);
@@ -931,7 +932,8 @@
(unsigned int) event->flags);
/* Look for common error cases */
- switch (GET_COMP_CODE(event->transfer_len)) {
+ trb_comp_code = GET_COMP_CODE(event->transfer_len);
+ switch (trb_comp_code) {
/* Skip codes that require special handling depending on
* transfer type
*/
@@ -974,7 +976,7 @@
/* Was this a control transfer? */
if (usb_endpoint_xfer_control(&td->urb->ep->desc)) {
xhci_debug_trb(xhci, xhci->event_ring->dequeue);
- switch (GET_COMP_CODE(event->transfer_len)) {
+ switch (trb_comp_code) {
case COMP_SUCCESS:
if (event_trb == ep_ring->dequeue) {
xhci_warn(xhci, "WARN: Success on ctrl setup TRB without IOC set??\n");
@@ -1031,7 +1033,7 @@
}
} else {
/* Maybe the event was for the data stage? */
- if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) {
+ if (trb_comp_code != COMP_STOP_INVAL) {
/* We didn't stop on a link TRB in the middle */
td->urb->actual_length =
td->urb->transfer_buffer_length -
@@ -1043,7 +1045,7 @@
}
}
} else {
- switch (GET_COMP_CODE(event->transfer_len)) {
+ switch (trb_comp_code) {
case COMP_SUCCESS:
/* Double check that the HW transferred everything. */
if (event_trb != td->last_trb) {
@@ -1120,14 +1122,14 @@
/* If the ring didn't stop on a Link or No-op TRB, add
* in the actual bytes transferred from the Normal TRB
*/
- if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL)
+ if (trb_comp_code != COMP_STOP_INVAL)
td->urb->actual_length +=
TRB_LEN(cur_trb->generic.field[2]) -
TRB_LEN(event->transfer_len);
}
}
- if (GET_COMP_CODE(event->transfer_len) == COMP_STOP_INVAL ||
- GET_COMP_CODE(event->transfer_len) == COMP_STOP) {
+ if (trb_comp_code == COMP_STOP_INVAL ||
+ trb_comp_code == COMP_STOP) {
/* The Endpoint Stop Command completion will take care of any
* stopped TDs. A stopped TD may be restarted, so don't update
* the ring dequeue pointer or take this TD off any lists yet.
