blob: 57196883a00e36e869491aab0b1ea027436d8f8f [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* PowerPC version
* Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org)
*
* Rewritten by Cort Dougan (cort@cs.nmt.edu) for PReP
* Copyright (C) 1996 Cort Dougan <cort@cs.nmt.edu>
* Adapted for Power Macintosh by Paul Mackerras.
* Low-level exception handlers and MMU support
* rewritten by Paul Mackerras.
* Copyright (C) 1996 Paul Mackerras.
* MPC8xx modifications Copyright (C) 1997 Dan Malek (dmalek@jlc.net).
*
* This file contains the low-level support and setup for the
* PowerPC platform, including trap and interrupt dispatch.
* (The PPC 8xx embedded CPUs use head_8xx.S instead.)
*/
#include <linux/init.h>
#include <linux/pgtable.h>
#include <linux/linkage.h>
#include <asm/reg.h>
#include <asm/page.h>
#include <asm/mmu.h>
#include <asm/cputable.h>
#include <asm/cache.h>
#include <asm/thread_info.h>
#include <asm/ppc_asm.h>
#include <asm/asm-offsets.h>
#include <asm/ptrace.h>
#include <asm/bug.h>
#include <asm/kvm_book3s_asm.h>
#include <asm/feature-fixups.h>
#include <asm/interrupt.h>
#include "head_32.h"
#define LOAD_BAT(n, reg, RA, RB) \
/* see the comment for clear_bats() -- Cort */ \
li RA,0; \
mtspr SPRN_IBAT##n##U,RA; \
mtspr SPRN_DBAT##n##U,RA; \
lwz RA,(n*16)+0(reg); \
lwz RB,(n*16)+4(reg); \
mtspr SPRN_IBAT##n##U,RA; \
mtspr SPRN_IBAT##n##L,RB; \
lwz RA,(n*16)+8(reg); \
lwz RB,(n*16)+12(reg); \
mtspr SPRN_DBAT##n##U,RA; \
mtspr SPRN_DBAT##n##L,RB
__HEAD
_GLOBAL(_stext);
/*
* _start is defined this way because the XCOFF loader in the OpenFirmware
* on the powermac expects the entry point to be a procedure descriptor.
*/
_GLOBAL(_start);
/*
* These are here for legacy reasons, the kernel used to
* need to look like a coff function entry for the pmac
* but we're always started by some kind of bootloader now.
* -- Cort
*/
nop /* used by __secondary_hold on prep (mtx) and chrp smp */
nop /* used by __secondary_hold on prep (mtx) and chrp smp */
nop
/* PMAC
* Enter here with the kernel text, data and bss loaded starting at
* 0, running with virtual == physical mapping.
* r5 points to the prom entry point (the client interface handler
* address). Address translation is turned on, with the prom
* managing the hash table. Interrupts are disabled. The stack
* pointer (r1) points to just below the end of the half-meg region
* from 0x380000 - 0x400000, which is mapped in already.
*
* If we are booted from MacOS via BootX, we enter with the kernel
* image loaded somewhere, and the following values in registers:
* r3: 'BooX' (0x426f6f58)
* r4: virtual address of boot_infos_t
* r5: 0
*
* PREP
* This is jumped to on prep systems right after the kernel is relocated
* to its proper place in memory by the boot loader. The expected layout
* of the regs is:
* r3: ptr to residual data
* r4: initrd_start or if no initrd then 0
* r5: initrd_end - unused if r4 is 0
* r6: Start of command line string
* r7: End of command line string
*
* This just gets a minimal mmu environment setup so we can call
* start_here() to do the real work.
* -- Cort
*/
.globl __start
__start:
/*
* We have to do any OF calls before we map ourselves to KERNELBASE,
* because OF may have I/O devices mapped into that area
* (particularly on CHRP).
*/
cmpwi 0,r5,0
beq 1f
#ifdef CONFIG_PPC_OF_BOOT_TRAMPOLINE
/* find out where we are now */
bcl 20,31,$+4
0: mflr r8 /* r8 = runtime addr here */
addis r8,r8,(_stext - 0b)@ha
addi r8,r8,(_stext - 0b)@l /* current runtime base addr */
bl prom_init
#endif /* CONFIG_PPC_OF_BOOT_TRAMPOLINE */
/* We never return. We also hit that trap if trying to boot
* from OF while CONFIG_PPC_OF_BOOT_TRAMPOLINE isn't selected */
trap
/*
* Check for BootX signature when supporting PowerMac and branch to
* appropriate trampoline if it's present
*/
#ifdef CONFIG_PPC_PMAC
1: lis r31,0x426f
ori r31,r31,0x6f58
cmpw 0,r3,r31
bne 1f
bl bootx_init
trap
#endif /* CONFIG_PPC_PMAC */
1: mr r31,r3 /* save device tree ptr */
li r24,0 /* cpu # */
/*
* early_init() does the early machine identification and does
* the necessary low-level setup and clears the BSS
* -- Cort <cort@fsmlabs.com>
*/
bl early_init
/* Switch MMU off, clear BATs and flush TLB. At this point, r3 contains
* the physical address we are running at, returned by early_init()
*/
bl mmu_off
__after_mmu_off:
bl clear_bats
bl flush_tlbs
bl initial_bats
bl load_segment_registers
bl reloc_offset
bl early_hash_table
#if defined(CONFIG_BOOTX_TEXT)
bl setup_disp_bat
#endif
#ifdef CONFIG_PPC_EARLY_DEBUG_CPM
bl setup_cpm_bat
#endif
#ifdef CONFIG_PPC_EARLY_DEBUG_USBGECKO
bl setup_usbgecko_bat
#endif
/*
* Call setup_cpu for CPU 0 and initialize 6xx Idle
*/
bl reloc_offset
li r24,0 /* cpu# */
bl call_setup_cpu /* Call setup_cpu for this CPU */
bl reloc_offset
bl init_idle_6xx
/*
* We need to run with _start at physical address 0.
* On CHRP, we are loaded at 0x10000 since OF on CHRP uses
* the exception vectors at 0 (and therefore this copy
* overwrites OF's exception vectors with our own).
* The MMU is off at this point.
*/
bl reloc_offset
mr r26,r3
addis r4,r3,KERNELBASE@h /* current address of _start */
lis r5,PHYSICAL_START@h
cmplw 0,r4,r5 /* already running at PHYSICAL_START? */
bne relocate_kernel
/*
* we now have the 1st 16M of ram mapped with the bats.
* prep needs the mmu to be turned on here, but pmac already has it on.
* this shouldn't bother the pmac since it just gets turned on again
* as we jump to our code at KERNELBASE. -- Cort
* Actually no, pmac doesn't have it on any more. BootX enters with MMU
* off, and in other cases, we now turn it off before changing BATs above.
*/
turn_on_mmu:
mfmsr r0
ori r0,r0,MSR_DR|MSR_IR|MSR_RI
mtspr SPRN_SRR1,r0
lis r0,start_here@h
ori r0,r0,start_here@l
mtspr SPRN_SRR0,r0
rfi /* enables MMU */
/*
* We need __secondary_hold as a place to hold the other cpus on
* an SMP machine, even when we are running a UP kernel.
*/
. = 0xc0 /* for prep bootloader */
li r3,1 /* MTX only has 1 cpu */
.globl __secondary_hold
__secondary_hold:
/* tell the master we're here */
stw r3,__secondary_hold_acknowledge@l(0)
#ifdef CONFIG_SMP
100: lwz r4,0(0)
/* wait until we're told to start */
cmpw 0,r4,r3
bne 100b
/* our cpu # was at addr 0 - go */
mr r24,r3 /* cpu # */
b __secondary_start
#else
b .
#endif /* CONFIG_SMP */
.globl __secondary_hold_spinloop
__secondary_hold_spinloop:
.long 0
.globl __secondary_hold_acknowledge
__secondary_hold_acknowledge:
.long -1
/* System reset */
/* core99 pmac starts the seconary here by changing the vector, and
putting it back to what it was (unknown_async_exception) when done. */
EXCEPTION(INTERRUPT_SYSTEM_RESET, Reset, unknown_async_exception)
/* Machine check */
/*
* On CHRP, this is complicated by the fact that we could get a
* machine check inside RTAS, and we have no guarantee that certain
* critical registers will have the values we expect. The set of
* registers that might have bad values includes all the GPRs
* and all the BATs. We indicate that we are in RTAS by putting
* a non-zero value, the address of the exception frame to use,
* in thread.rtas_sp. The machine check handler checks thread.rtas_sp
* and uses its value if it is non-zero.
* (Other exception handlers assume that r1 is a valid kernel stack
* pointer when we take an exception from supervisor mode.)
* -- paulus.
*/
START_EXCEPTION(INTERRUPT_MACHINE_CHECK, MachineCheck)
EXCEPTION_PROLOG_0
#ifdef CONFIG_PPC_CHRP
mtspr SPRN_SPRG_SCRATCH2,r1
mfspr r1, SPRN_SPRG_THREAD
lwz r1, RTAS_SP(r1)
cmpwi cr1, r1, 0
bne cr1, 7f
mfspr r1, SPRN_SPRG_SCRATCH2
#endif /* CONFIG_PPC_CHRP */
EXCEPTION_PROLOG_1
7: EXCEPTION_PROLOG_2 0x200 MachineCheck
#ifdef CONFIG_PPC_CHRP
beq cr1, 1f
twi 31, 0, 0
#endif
1: prepare_transfer_to_handler
bl machine_check_exception
b interrupt_return
/* Data access exception. */
START_EXCEPTION(INTERRUPT_DATA_STORAGE, DataAccess)
#ifdef CONFIG_PPC_BOOK3S_604
BEGIN_MMU_FTR_SECTION
mtspr SPRN_SPRG_SCRATCH2,r10
mfspr r10, SPRN_SPRG_THREAD
stw r11, THR11(r10)
mfspr r10, SPRN_DSISR
mfcr r11
andis. r10, r10, (DSISR_BAD_FAULT_32S | DSISR_DABRMATCH)@h
mfspr r10, SPRN_SPRG_THREAD
beq hash_page_dsi
.Lhash_page_dsi_cont:
mtcr r11
lwz r11, THR11(r10)
mfspr r10, SPRN_SPRG_SCRATCH2
MMU_FTR_SECTION_ELSE
b 1f
ALT_MMU_FTR_SECTION_END_IFSET(MMU_FTR_HPTE_TABLE)
#endif
1: EXCEPTION_PROLOG_0 handle_dar_dsisr=1
EXCEPTION_PROLOG_1
EXCEPTION_PROLOG_2 INTERRUPT_DATA_STORAGE DataAccess handle_dar_dsisr=1
prepare_transfer_to_handler
lwz r5, _DSISR(r1)
andis. r0, r5, DSISR_DABRMATCH@h
bne- 1f
bl do_page_fault
b interrupt_return
1: bl do_break
REST_NVGPRS(r1)
b interrupt_return
/* Instruction access exception. */
START_EXCEPTION(INTERRUPT_INST_STORAGE, InstructionAccess)
mtspr SPRN_SPRG_SCRATCH0,r10
mtspr SPRN_SPRG_SCRATCH1,r11
mfspr r10, SPRN_SPRG_THREAD
mfspr r11, SPRN_SRR0
stw r11, SRR0(r10)
mfspr r11, SPRN_SRR1 /* check whether user or kernel */
stw r11, SRR1(r10)
mfcr r10
#ifdef CONFIG_PPC_BOOK3S_604
BEGIN_MMU_FTR_SECTION
andis. r11, r11, SRR1_ISI_NOPT@h /* no pte found? */
bne hash_page_isi
.Lhash_page_isi_cont:
mfspr r11, SPRN_SRR1 /* check whether user or kernel */
END_MMU_FTR_SECTION_IFSET(MMU_FTR_HPTE_TABLE)
#endif
andi. r11, r11, MSR_PR
EXCEPTION_PROLOG_1
EXCEPTION_PROLOG_2 INTERRUPT_INST_STORAGE InstructionAccess
andis. r5,r9,DSISR_SRR1_MATCH_32S@h /* Filter relevant SRR1 bits */
stw r5, _DSISR(r11)
stw r12, _DAR(r11)
prepare_transfer_to_handler
bl do_page_fault
b interrupt_return
/* External interrupt */
EXCEPTION(INTERRUPT_EXTERNAL, HardwareInterrupt, do_IRQ)
/* Alignment exception */
START_EXCEPTION(INTERRUPT_ALIGNMENT, Alignment)
EXCEPTION_PROLOG INTERRUPT_ALIGNMENT Alignment handle_dar_dsisr=1
prepare_transfer_to_handler
bl alignment_exception
REST_NVGPRS(r1)
b interrupt_return
/* Program check exception */
START_EXCEPTION(INTERRUPT_PROGRAM, ProgramCheck)
EXCEPTION_PROLOG INTERRUPT_PROGRAM ProgramCheck
prepare_transfer_to_handler
bl program_check_exception
REST_NVGPRS(r1)
b interrupt_return
/* Floating-point unavailable */
START_EXCEPTION(0x800, FPUnavailable)
#ifdef CONFIG_PPC_FPU
BEGIN_FTR_SECTION
/*
* Certain Freescale cores don't have a FPU and treat fp instructions
* as a FP Unavailable exception. Redirect to illegal/emulation handling.
*/
b ProgramCheck
END_FTR_SECTION_IFSET(CPU_FTR_FPU_UNAVAILABLE)
EXCEPTION_PROLOG INTERRUPT_FP_UNAVAIL FPUnavailable
beq 1f
bl load_up_fpu /* if from user, just load it up */
b fast_exception_return
1: prepare_transfer_to_handler
bl kernel_fp_unavailable_exception
b interrupt_return
#else
b ProgramCheck
#endif
/* Decrementer */
EXCEPTION(INTERRUPT_DECREMENTER, Decrementer, timer_interrupt)
EXCEPTION(0xa00, Trap_0a, unknown_exception)
EXCEPTION(0xb00, Trap_0b, unknown_exception)
/* System call */
START_EXCEPTION(INTERRUPT_SYSCALL, SystemCall)
SYSCALL_ENTRY INTERRUPT_SYSCALL
EXCEPTION(INTERRUPT_TRACE, SingleStep, single_step_exception)
EXCEPTION(0xe00, Trap_0e, unknown_exception)
/*
* The Altivec unavailable trap is at 0x0f20. Foo.
* We effectively remap it to 0x3000.
* We include an altivec unavailable exception vector even if
* not configured for Altivec, so that you can't panic a
* non-altivec kernel running on a machine with altivec just
* by executing an altivec instruction.
*/
START_EXCEPTION(INTERRUPT_PERFMON, PerformanceMonitorTrap)
b PerformanceMonitor
START_EXCEPTION(INTERRUPT_ALTIVEC_UNAVAIL, AltiVecUnavailableTrap)
b AltiVecUnavailable
__HEAD
/*
* Handle TLB miss for instruction on 603/603e.
* Note: we get an alternate set of r0 - r3 to use automatically.
*/
. = INTERRUPT_INST_TLB_MISS_603
InstructionTLBMiss:
/*
* r0: userspace flag (later scratch)
* r1: linux style pte ( later becomes ppc hardware pte )
* r2: ptr to linux-style pte
* r3: fault address
*/
/* Get PTE (linux-style) and check access */
mfspr r3,SPRN_IMISS
#ifdef CONFIG_EXECMEM
lis r1, TASK_SIZE@h /* check if kernel address */
cmplw 0,r1,r3
#endif
mfspr r2, SPRN_SDR1
li r1,_PAGE_PRESENT | _PAGE_ACCESSED | _PAGE_EXEC
rlwinm r2, r2, 28, 0xfffff000
#ifdef CONFIG_EXECMEM
li r0, 3
bgt- 112f
lis r2, (swapper_pg_dir - PAGE_OFFSET)@ha /* if kernel address, use */
li r0, 0
addi r2, r2, (swapper_pg_dir - PAGE_OFFSET)@l /* kernel page table */
#endif
112: rlwimi r2,r3,12,20,29 /* insert top 10 bits of address */
lwz r2,0(r2) /* get pmd entry */
rlwinm. r2,r2,0,0,19 /* extract address of pte page */
beq- InstructionAddressInvalid /* return if no mapping */
rlwimi r2,r3,22,20,29 /* insert next 10 bits of address */
lwz r2,0(r2) /* get linux-style pte */
andc. r1,r1,r2 /* check access & ~permission */
bne- InstructionAddressInvalid /* return if access not permitted */
/* Convert linux-style PTE to low word of PPC-style PTE */
#ifdef CONFIG_EXECMEM
rlwimi r2, r0, 0, 31, 31 /* userspace ? -> PP lsb */
#endif
ori r1, r1, 0xe06 /* clear out reserved bits */
andc r1, r2, r1 /* PP = user? 1 : 0 */
BEGIN_FTR_SECTION
rlwinm r1,r1,0,~_PAGE_COHERENT /* clear M (coherence not required) */
END_FTR_SECTION_IFCLR(CPU_FTR_NEED_COHERENT)
mtspr SPRN_RPA,r1
tlbli r3
mfspr r3,SPRN_SRR1 /* Need to restore CR0 */
mtcrf 0x80,r3
rfi
InstructionAddressInvalid:
mfspr r3,SPRN_SRR1
rlwinm r1,r3,9,6,6 /* Get load/store bit */
addis r1,r1,0x2000
mtspr SPRN_DSISR,r1 /* (shouldn't be needed) */
andi. r2,r3,0xFFFF /* Clear upper bits of SRR1 */
or r2,r2,r1
mtspr SPRN_SRR1,r2
mfspr r1,SPRN_IMISS /* Get failing address */
rlwinm. r2,r2,0,31,31 /* Check for little endian access */
rlwimi r2,r2,1,30,30 /* change 1 -> 3 */
xor r1,r1,r2
mtspr SPRN_DAR,r1 /* Set fault address */
mfmsr r0 /* Restore "normal" registers */
xoris r0,r0,MSR_TGPR>>16
mtcrf 0x80,r3 /* Restore CR0 */
mtmsr r0
b InstructionAccess
/*
* Handle TLB miss for DATA Load operation on 603/603e
*/
. = INTERRUPT_DATA_LOAD_TLB_MISS_603
DataLoadTLBMiss:
/*
* r0: userspace flag (later scratch)
* r1: linux style pte ( later becomes ppc hardware pte )
* r2: ptr to linux-style pte
* r3: fault address
*/
/* Get PTE (linux-style) and check access */
mfspr r3,SPRN_DMISS
lis r1, TASK_SIZE@h /* check if kernel address */
cmplw 0,r1,r3
mfspr r2, SPRN_SDR1
li r1, _PAGE_PRESENT | _PAGE_ACCESSED | _PAGE_READ
rlwinm r2, r2, 28, 0xfffff000
li r0, 3
bgt- 112f
lis r2, (swapper_pg_dir - PAGE_OFFSET)@ha /* if kernel address, use */
li r0, 0
addi r2, r2, (swapper_pg_dir - PAGE_OFFSET)@l /* kernel page table */
112: rlwimi r2,r3,12,20,29 /* insert top 10 bits of address */
lwz r2,0(r2) /* get pmd entry */
rlwinm. r2,r2,0,0,19 /* extract address of pte page */
beq- DataAddressInvalid /* return if no mapping */
rlwimi r2,r3,22,20,29 /* insert next 10 bits of address */
lwz r2,0(r2) /* get linux-style pte */
andc. r1,r1,r2 /* check access & ~permission */
bne- DataAddressInvalid /* return if access not permitted */
/* Convert linux-style PTE to low word of PPC-style PTE */
rlwinm r1,r2,32-9,30,30 /* _PAGE_WRITE -> PP msb */
rlwimi r2,r0,0,30,31 /* userspace ? -> PP */
rlwimi r1,r2,32-3,24,24 /* _PAGE_WRITE -> _PAGE_DIRTY */
xori r1,r1,_PAGE_DIRTY /* clear dirty when not rw */
ori r1,r1,0xe04 /* clear out reserved bits */
andc r1,r2,r1 /* PP = user? rw? 1: 3: 0 */
BEGIN_FTR_SECTION
rlwinm r1,r1,0,~_PAGE_COHERENT /* clear M (coherence not required) */
END_FTR_SECTION_IFCLR(CPU_FTR_NEED_COHERENT)
mtspr SPRN_RPA,r1
BEGIN_MMU_FTR_SECTION
li r0,1
mfspr r1,SPRN_SPRG_603_LRU
rlwinm r2,r3,20,27,31 /* Get Address bits 15:19 */
slw r0,r0,r2
xor r1,r0,r1
srw r0,r1,r2
mtspr SPRN_SPRG_603_LRU,r1
mfspr r2,SPRN_SRR1
rlwimi r2,r0,31-14,14,14
mtspr SPRN_SRR1,r2
mtcrf 0x80,r2
tlbld r3
rfi
MMU_FTR_SECTION_ELSE
mfspr r2,SPRN_SRR1 /* Need to restore CR0 */
mtcrf 0x80,r2
tlbld r3
rfi
ALT_MMU_FTR_SECTION_END_IFSET(MMU_FTR_NEED_DTLB_SW_LRU)
DataAddressInvalid:
mfspr r3,SPRN_SRR1
rlwinm r1,r3,9,6,6 /* Get load/store bit */
addis r1,r1,0x2000
mtspr SPRN_DSISR,r1
andi. r2,r3,0xFFFF /* Clear upper bits of SRR1 */
mtspr SPRN_SRR1,r2
mfspr r1,SPRN_DMISS /* Get failing address */
rlwinm. r2,r2,0,31,31 /* Check for little endian access */
beq 20f /* Jump if big endian */
xori r1,r1,3
20: mtspr SPRN_DAR,r1 /* Set fault address */
mfmsr r0 /* Restore "normal" registers */
xoris r0,r0,MSR_TGPR>>16
mtcrf 0x80,r3 /* Restore CR0 */
mtmsr r0
b DataAccess
/*
* Handle TLB miss for DATA Store on 603/603e
*/
. = INTERRUPT_DATA_STORE_TLB_MISS_603
DataStoreTLBMiss:
/*
* r0: userspace flag (later scratch)
* r1: linux style pte ( later becomes ppc hardware pte )
* r2: ptr to linux-style pte
* r3: fault address
*/
/* Get PTE (linux-style) and check access */
mfspr r3,SPRN_DMISS
lis r1, TASK_SIZE@h /* check if kernel address */
cmplw 0,r1,r3
mfspr r2, SPRN_SDR1
li r1, _PAGE_RW | _PAGE_DIRTY | _PAGE_PRESENT | _PAGE_ACCESSED
rlwinm r2, r2, 28, 0xfffff000
li r0, 3
bgt- 112f
lis r2, (swapper_pg_dir - PAGE_OFFSET)@ha /* if kernel address, use */
li r0, 0
addi r2, r2, (swapper_pg_dir - PAGE_OFFSET)@l /* kernel page table */
112: rlwimi r2,r3,12,20,29 /* insert top 10 bits of address */
lwz r2,0(r2) /* get pmd entry */
rlwinm. r2,r2,0,0,19 /* extract address of pte page */
beq- DataAddressInvalid /* return if no mapping */
rlwimi r2,r3,22,20,29 /* insert next 10 bits of address */
lwz r2,0(r2) /* get linux-style pte */
andc. r1,r1,r2 /* check access & ~permission */
bne- DataAddressInvalid /* return if access not permitted */
/* Convert linux-style PTE to low word of PPC-style PTE */
rlwimi r2,r0,0,31,31 /* userspace ? -> PP lsb */
li r1,0xe06 /* clear out reserved bits & PP msb */
andc r1,r2,r1 /* PP = user? 1: 0 */
BEGIN_FTR_SECTION
rlwinm r1,r1,0,~_PAGE_COHERENT /* clear M (coherence not required) */
END_FTR_SECTION_IFCLR(CPU_FTR_NEED_COHERENT)
mtspr SPRN_RPA,r1
mfspr r2,SPRN_SRR1 /* Need to restore CR0 */
mtcrf 0x80,r2
BEGIN_MMU_FTR_SECTION
li r0,1
mfspr r1,SPRN_SPRG_603_LRU
rlwinm r2,r3,20,27,31 /* Get Address bits 15:19 */
slw r0,r0,r2
xor r1,r0,r1
srw r0,r1,r2
mtspr SPRN_SPRG_603_LRU,r1
mfspr r2,SPRN_SRR1
rlwimi r2,r0,31-14,14,14
mtspr SPRN_SRR1,r2
mtcrf 0x80,r2
tlbld r3
rfi
MMU_FTR_SECTION_ELSE
mfspr r2,SPRN_SRR1 /* Need to restore CR0 */
mtcrf 0x80,r2
tlbld r3
rfi
ALT_MMU_FTR_SECTION_END_IFSET(MMU_FTR_NEED_DTLB_SW_LRU)
#ifndef CONFIG_ALTIVEC
#define altivec_assist_exception unknown_exception
#endif
#ifndef CONFIG_TAU_INT
#define TAUException unknown_async_exception
#endif
EXCEPTION(0x1300, Trap_13, instruction_breakpoint_exception)
EXCEPTION(0x1400, SMI, SMIException)
EXCEPTION(0x1500, Trap_15, unknown_exception)
EXCEPTION(0x1600, Trap_16, altivec_assist_exception)
EXCEPTION(0x1700, Trap_17, TAUException)
EXCEPTION(0x1800, Trap_18, unknown_exception)
EXCEPTION(0x1900, Trap_19, unknown_exception)
EXCEPTION(0x1a00, Trap_1a, unknown_exception)
EXCEPTION(0x1b00, Trap_1b, unknown_exception)
EXCEPTION(0x1c00, Trap_1c, unknown_exception)
EXCEPTION(0x1d00, Trap_1d, unknown_exception)
EXCEPTION(0x1e00, Trap_1e, unknown_exception)
EXCEPTION(0x1f00, Trap_1f, unknown_exception)
EXCEPTION(0x2000, RunMode, RunModeException)
EXCEPTION(0x2100, Trap_21, unknown_exception)
EXCEPTION(0x2200, Trap_22, unknown_exception)
EXCEPTION(0x2300, Trap_23, unknown_exception)
EXCEPTION(0x2400, Trap_24, unknown_exception)
EXCEPTION(0x2500, Trap_25, unknown_exception)
EXCEPTION(0x2600, Trap_26, unknown_exception)
EXCEPTION(0x2700, Trap_27, unknown_exception)
EXCEPTION(0x2800, Trap_28, unknown_exception)
EXCEPTION(0x2900, Trap_29, unknown_exception)
EXCEPTION(0x2a00, Trap_2a, unknown_exception)
EXCEPTION(0x2b00, Trap_2b, unknown_exception)
EXCEPTION(0x2c00, Trap_2c, unknown_exception)
EXCEPTION(0x2d00, Trap_2d, unknown_exception)
EXCEPTION(0x2e00, Trap_2e, unknown_exception)
EXCEPTION(0x2f00, Trap_2f, unknown_exception)
__HEAD
. = 0x3000
#ifdef CONFIG_PPC_BOOK3S_604
.macro save_regs_thread thread
stw r0, THR0(\thread)
stw r3, THR3(\thread)
stw r4, THR4(\thread)
stw r5, THR5(\thread)
stw r6, THR6(\thread)
stw r8, THR8(\thread)
stw r9, THR9(\thread)
mflr r0
stw r0, THLR(\thread)
mfctr r0
stw r0, THCTR(\thread)
.endm
.macro restore_regs_thread thread
lwz r0, THLR(\thread)
mtlr r0
lwz r0, THCTR(\thread)
mtctr r0
lwz r0, THR0(\thread)
lwz r3, THR3(\thread)
lwz r4, THR4(\thread)
lwz r5, THR5(\thread)
lwz r6, THR6(\thread)
lwz r8, THR8(\thread)
lwz r9, THR9(\thread)
.endm
hash_page_dsi:
save_regs_thread r10
mfdsisr r3
mfdar r4
mfsrr0 r5
mfsrr1 r9
rlwinm r3, r3, 32 - 15, _PAGE_WRITE /* DSISR_STORE -> _PAGE_WRITE */
ori r3, r3, _PAGE_PRESENT | _PAGE_READ
bl hash_page
mfspr r10, SPRN_SPRG_THREAD
restore_regs_thread r10
b .Lhash_page_dsi_cont
hash_page_isi:
mr r11, r10
mfspr r10, SPRN_SPRG_THREAD
save_regs_thread r10
li r3, _PAGE_PRESENT | _PAGE_EXEC
lwz r4, SRR0(r10)
lwz r9, SRR1(r10)
bl hash_page
mfspr r10, SPRN_SPRG_THREAD
restore_regs_thread r10
mr r10, r11
b .Lhash_page_isi_cont
.globl fast_hash_page_return
fast_hash_page_return:
andis. r10, r9, SRR1_ISI_NOPT@h /* Set on ISI, cleared on DSI */
mfspr r10, SPRN_SPRG_THREAD
restore_regs_thread r10
bne 1f
/* DSI */
mtcr r11
lwz r11, THR11(r10)
mfspr r10, SPRN_SPRG_SCRATCH2
rfi
1: /* ISI */
mtcr r11
mfspr r11, SPRN_SPRG_SCRATCH1
mfspr r10, SPRN_SPRG_SCRATCH0
rfi
#endif /* CONFIG_PPC_BOOK3S_604 */
#ifdef CONFIG_VMAP_STACK
vmap_stack_overflow_exception
#endif
__HEAD
AltiVecUnavailable:
EXCEPTION_PROLOG 0xf20 AltiVecUnavailable
#ifdef CONFIG_ALTIVEC
beq 1f
bl load_up_altivec /* if from user, just load it up */
b fast_exception_return
#endif /* CONFIG_ALTIVEC */
1: prepare_transfer_to_handler
bl altivec_unavailable_exception
b interrupt_return
__HEAD
PerformanceMonitor:
EXCEPTION_PROLOG 0xf00 PerformanceMonitor
prepare_transfer_to_handler
bl performance_monitor_exception
b interrupt_return
__HEAD
/*
* This code is jumped to from the startup code to copy
* the kernel image to physical address PHYSICAL_START.
*/
relocate_kernel:
lis r3,PHYSICAL_START@h /* Destination base address */
li r6,0 /* Destination offset */
li r5,0x4000 /* # bytes of memory to copy */
bl copy_and_flush /* copy the first 0x4000 bytes */
addi r0,r3,4f@l /* jump to the address of 4f */
mtctr r0 /* in copy and do the rest. */
bctr /* jump to the copy */
4: lis r5,_end-KERNELBASE@h
ori r5,r5,_end-KERNELBASE@l
bl copy_and_flush /* copy the rest */
b turn_on_mmu
/*
* Copy routine used to copy the kernel to start at physical address 0
* and flush and invalidate the caches as needed.
* r3 = dest addr, r4 = source addr, r5 = copy limit, r6 = start offset
* on exit, r3, r4, r5 are unchanged, r6 is updated to be >= r5.
*/
_GLOBAL(copy_and_flush)
addi r5,r5,-4
addi r6,r6,-4
4: li r0,L1_CACHE_BYTES/4
mtctr r0
3: addi r6,r6,4 /* copy a cache line */
lwzx r0,r6,r4
stwx r0,r6,r3
bdnz 3b
dcbst r6,r3 /* write it to memory */
sync
icbi r6,r3 /* flush the icache line */
cmplw 0,r6,r5
blt 4b
sync /* additional sync needed on g4 */
isync
addi r5,r5,4
addi r6,r6,4
blr
#ifdef CONFIG_SMP
.globl __secondary_start_mpc86xx
__secondary_start_mpc86xx:
mfspr r3, SPRN_PIR
stw r3, __secondary_hold_acknowledge@l(0)
mr r24, r3 /* cpu # */
b __secondary_start
.globl __secondary_start_pmac_0
__secondary_start_pmac_0:
/* NB the entries for cpus 0, 1, 2 must each occupy 8 bytes. */
li r24,0
b 1f
li r24,1
b 1f
li r24,2
b 1f
li r24,3
1:
/* on powersurge, we come in here with IR=0 and DR=1, and DBAT 0
set to map the 0xf0000000 - 0xffffffff region */
mfmsr r0
rlwinm r0,r0,0,28,26 /* clear DR (0x10) */
mtmsr r0
isync
.globl __secondary_start
__secondary_start:
/* Copy some CPU settings from CPU 0 */
bl __restore_cpu_setup
lis r3,-KERNELBASE@h
mr r4,r24
bl call_setup_cpu /* Call setup_cpu for this CPU */
lis r3,-KERNELBASE@h
bl init_idle_6xx
/* get current's stack and current */
lis r2,secondary_current@ha
tophys(r2,r2)
lwz r2,secondary_current@l(r2)
tophys(r1,r2)
lwz r1,TASK_STACK(r1)
/* stack */
addi r1,r1,THREAD_SIZE-STACK_FRAME_MIN_SIZE
li r0,0
tophys(r3,r1)
stw r0,0(r3)
/* load up the MMU */
bl load_segment_registers
bl load_up_mmu
/* ptr to phys current thread */
tophys(r4,r2)
addi r4,r4,THREAD /* phys address of our thread_struct */
mtspr SPRN_SPRG_THREAD,r4
BEGIN_MMU_FTR_SECTION
lis r4, (swapper_pg_dir - PAGE_OFFSET)@h
ori r4, r4, (swapper_pg_dir - PAGE_OFFSET)@l
rlwinm r4, r4, 4, 0xffff01ff
mtspr SPRN_SDR1, r4
END_MMU_FTR_SECTION_IFCLR(MMU_FTR_HPTE_TABLE)
/* enable MMU and jump to start_secondary */
li r4,MSR_KERNEL
lis r3,start_secondary@h
ori r3,r3,start_secondary@l
mtspr SPRN_SRR0,r3
mtspr SPRN_SRR1,r4
rfi
#endif /* CONFIG_SMP */
#ifdef CONFIG_KVM_BOOK3S_HANDLER
#include "../kvm/book3s_rmhandlers.S"
#endif
/*
* Load stuff into the MMU. Intended to be called with
* IR=0 and DR=0.
*/
SYM_FUNC_START_LOCAL(early_hash_table)
sync /* Force all PTE updates to finish */
isync
tlbia /* Clear all TLB entries */
sync /* wait for tlbia/tlbie to finish */
TLBSYNC /* ... on all CPUs */
/* Load the SDR1 register (hash table base & size) */
lis r6, early_hash - PAGE_OFFSET@h
ori r6, r6, 3 /* 256kB table */
mtspr SPRN_SDR1, r6
blr
SYM_FUNC_END(early_hash_table)
SYM_FUNC_START_LOCAL(load_up_mmu)
sync /* Force all PTE updates to finish */
isync
tlbia /* Clear all TLB entries */
sync /* wait for tlbia/tlbie to finish */
TLBSYNC /* ... on all CPUs */
BEGIN_MMU_FTR_SECTION
/* Load the SDR1 register (hash table base & size) */
lis r6,_SDR1@ha
tophys(r6,r6)
lwz r6,_SDR1@l(r6)
mtspr SPRN_SDR1,r6
END_MMU_FTR_SECTION_IFSET(MMU_FTR_HPTE_TABLE)
/* Load the BAT registers with the values set up by MMU_init. */
lis r3,BATS@ha
addi r3,r3,BATS@l
tophys(r3,r3)
LOAD_BAT(0,r3,r4,r5)
LOAD_BAT(1,r3,r4,r5)
LOAD_BAT(2,r3,r4,r5)
LOAD_BAT(3,r3,r4,r5)
BEGIN_MMU_FTR_SECTION
LOAD_BAT(4,r3,r4,r5)
LOAD_BAT(5,r3,r4,r5)
LOAD_BAT(6,r3,r4,r5)
LOAD_BAT(7,r3,r4,r5)
END_MMU_FTR_SECTION_IFSET(MMU_FTR_USE_HIGH_BATS)
blr
SYM_FUNC_END(load_up_mmu)
_GLOBAL(load_segment_registers)
li r0, NUM_USER_SEGMENTS /* load up user segment register values */
mtctr r0 /* for context 0 */
#ifdef CONFIG_PPC_KUEP
lis r3, SR_NX@h /* Kp = 0, Ks = 0, VSID = 0 */
#else
li r3, 0 /* Kp = 0, Ks = 0, VSID = 0 */
#endif
li r4, 0
3: mtsrin r3, r4
addi r3, r3, 0x111 /* increment VSID */
addis r4, r4, 0x1000 /* address of next segment */
bdnz 3b
li r0, 16 - NUM_USER_SEGMENTS /* load up kernel segment registers */
mtctr r0 /* for context 0 */
rlwinm r3, r3, 0, ~SR_NX /* Nx = 0 */
rlwinm r3, r3, 0, ~SR_KS /* Ks = 0 */
oris r3, r3, SR_KP@h /* Kp = 1 */
3: mtsrin r3, r4
addi r3, r3, 0x111 /* increment VSID */
addis r4, r4, 0x1000 /* address of next segment */
bdnz 3b
blr
/*
* This is where the main kernel code starts.
*/
start_here:
/* ptr to current */
lis r2,init_task@h
ori r2,r2,init_task@l
/* Set up for using our exception vectors */
/* ptr to phys current thread */
tophys(r4,r2)
addi r4,r4,THREAD /* init task's THREAD */
mtspr SPRN_SPRG_THREAD,r4
BEGIN_MMU_FTR_SECTION
lis r4, (swapper_pg_dir - PAGE_OFFSET)@h
ori r4, r4, (swapper_pg_dir - PAGE_OFFSET)@l
rlwinm r4, r4, 4, 0xffff01ff
mtspr SPRN_SDR1, r4
END_MMU_FTR_SECTION_IFCLR(MMU_FTR_HPTE_TABLE)
/* stack */
lis r1,init_thread_union@ha
addi r1,r1,init_thread_union@l
li r0,0
stwu r0,THREAD_SIZE-STACK_FRAME_MIN_SIZE(r1)
/*
* Do early platform-specific initialization,
* and set up the MMU.
*/
#ifdef CONFIG_KASAN
bl kasan_early_init
#endif
li r3,0
mr r4,r31
bl machine_init
bl __save_cpu_setup
bl MMU_init
bl MMU_init_hw_patch
/*
* Go back to running unmapped so we can load up new values
* for SDR1 (hash table pointer) and the segment registers
* and change to using our exception vectors.
*/
lis r4,2f@h
ori r4,r4,2f@l
tophys(r4,r4)
li r3,MSR_KERNEL & ~(MSR_IR|MSR_DR)
.align 4
mtspr SPRN_SRR0,r4
mtspr SPRN_SRR1,r3
rfi
/* Load up the kernel context */
2: bl load_up_mmu
#ifdef CONFIG_BDI_SWITCH
/* Add helper information for the Abatron bdiGDB debugger.
* We do this here because we know the mmu is disabled, and
* will be enabled for real in just a few instructions.
*/
lis r5, abatron_pteptrs@h
ori r5, r5, abatron_pteptrs@l
stw r5, 0xf0(0) /* This much match your Abatron config */
lis r6, swapper_pg_dir@h
ori r6, r6, swapper_pg_dir@l
tophys(r5, r5)
stw r6, 0(r5)
#endif /* CONFIG_BDI_SWITCH */
/* Now turn on the MMU for real! */
li r4,MSR_KERNEL
lis r3,start_kernel@h
ori r3,r3,start_kernel@l
mtspr SPRN_SRR0,r3
mtspr SPRN_SRR1,r4
rfi
/*
* An undocumented "feature" of 604e requires that the v bit
* be cleared before changing BAT values.
*
* Also, newer IBM firmware does not clear bat3 and 4 so
* this makes sure it's done.
* -- Cort
*/
SYM_FUNC_START_LOCAL(clear_bats)
li r10,0
mtspr SPRN_DBAT0U,r10
mtspr SPRN_DBAT0L,r10
mtspr SPRN_DBAT1U,r10
mtspr SPRN_DBAT1L,r10
mtspr SPRN_DBAT2U,r10
mtspr SPRN_DBAT2L,r10
mtspr SPRN_DBAT3U,r10
mtspr SPRN_DBAT3L,r10
mtspr SPRN_IBAT0U,r10
mtspr SPRN_IBAT0L,r10
mtspr SPRN_IBAT1U,r10
mtspr SPRN_IBAT1L,r10
mtspr SPRN_IBAT2U,r10
mtspr SPRN_IBAT2L,r10
mtspr SPRN_IBAT3U,r10
mtspr SPRN_IBAT3L,r10
BEGIN_MMU_FTR_SECTION
/* Here's a tweak: at this point, CPU setup have
* not been called yet, so HIGH_BAT_EN may not be
* set in HID0 for the 745x processors. However, it
* seems that doesn't affect our ability to actually
* write to these SPRs.
*/
mtspr SPRN_DBAT4U,r10
mtspr SPRN_DBAT4L,r10
mtspr SPRN_DBAT5U,r10
mtspr SPRN_DBAT5L,r10
mtspr SPRN_DBAT6U,r10
mtspr SPRN_DBAT6L,r10
mtspr SPRN_DBAT7U,r10
mtspr SPRN_DBAT7L,r10
mtspr SPRN_IBAT4U,r10
mtspr SPRN_IBAT4L,r10
mtspr SPRN_IBAT5U,r10
mtspr SPRN_IBAT5L,r10
mtspr SPRN_IBAT6U,r10
mtspr SPRN_IBAT6L,r10
mtspr SPRN_IBAT7U,r10
mtspr SPRN_IBAT7L,r10
END_MMU_FTR_SECTION_IFSET(MMU_FTR_USE_HIGH_BATS)
blr
SYM_FUNC_END(clear_bats)
_GLOBAL(update_bats)
lis r4, 1f@h
ori r4, r4, 1f@l
tophys(r4, r4)
mfmsr r6
mflr r7
li r3, MSR_KERNEL & ~(MSR_IR | MSR_DR)
rlwinm r0, r6, 0, ~MSR_RI
rlwinm r0, r0, 0, ~MSR_EE
mtmsr r0
.align 4
mtspr SPRN_SRR0, r4
mtspr SPRN_SRR1, r3
rfi
1: bl clear_bats
lis r3, BATS@ha
addi r3, r3, BATS@l
tophys(r3, r3)
LOAD_BAT(0, r3, r4, r5)
LOAD_BAT(1, r3, r4, r5)
LOAD_BAT(2, r3, r4, r5)
LOAD_BAT(3, r3, r4, r5)
BEGIN_MMU_FTR_SECTION
LOAD_BAT(4, r3, r4, r5)
LOAD_BAT(5, r3, r4, r5)
LOAD_BAT(6, r3, r4, r5)
LOAD_BAT(7, r3, r4, r5)
END_MMU_FTR_SECTION_IFSET(MMU_FTR_USE_HIGH_BATS)
li r3, MSR_KERNEL & ~(MSR_IR | MSR_DR | MSR_RI)
mtmsr r3
mtspr SPRN_SRR0, r7
mtspr SPRN_SRR1, r6
rfi
SYM_FUNC_START_LOCAL(flush_tlbs)
lis r10, 0x40
1: addic. r10, r10, -0x1000
tlbie r10
bgt 1b
sync
blr
SYM_FUNC_END(flush_tlbs)
SYM_FUNC_START_LOCAL(mmu_off)
addi r4, r3, __after_mmu_off - _start
mfmsr r3
andi. r0,r3,MSR_DR|MSR_IR /* MMU enabled? */
beqlr
andc r3,r3,r0
.align 4
mtspr SPRN_SRR0,r4
mtspr SPRN_SRR1,r3
sync
rfi
SYM_FUNC_END(mmu_off)
/* We use one BAT to map up to 256M of RAM at _PAGE_OFFSET */
SYM_FUNC_START_LOCAL(initial_bats)
lis r11,PAGE_OFFSET@h
tophys(r8,r11)
#ifdef CONFIG_SMP
ori r8,r8,0x12 /* R/W access, M=1 */
#else
ori r8,r8,2 /* R/W access */
#endif /* CONFIG_SMP */
ori r11,r11,BL_256M<<2|0x2 /* set up BAT registers for 604 */
mtspr SPRN_DBAT0L,r8 /* N.B. 6xx have valid */
mtspr SPRN_DBAT0U,r11 /* bit in upper BAT register */
mtspr SPRN_IBAT0L,r8
mtspr SPRN_IBAT0U,r11
isync
blr
SYM_FUNC_END(initial_bats)
#ifdef CONFIG_BOOTX_TEXT
SYM_FUNC_START_LOCAL(setup_disp_bat)
/*
* setup the display bat prepared for us in prom.c
*/
mflr r8
bl reloc_offset
mtlr r8
addis r8,r3,disp_BAT@ha
addi r8,r8,disp_BAT@l
cmpwi cr0,r8,0
beqlr
lwz r11,0(r8)
lwz r8,4(r8)
mtspr SPRN_DBAT3L,r8
mtspr SPRN_DBAT3U,r11
blr
SYM_FUNC_END(setup_disp_bat)
#endif /* CONFIG_BOOTX_TEXT */
#ifdef CONFIG_PPC_EARLY_DEBUG_CPM
SYM_FUNC_START_LOCAL(setup_cpm_bat)
lis r8, 0xf000
ori r8, r8, 0x002a
mtspr SPRN_DBAT1L, r8
lis r11, 0xf000
ori r11, r11, (BL_1M << 2) | 2
mtspr SPRN_DBAT1U, r11
blr
SYM_FUNC_END(setup_cpm_bat)
#endif
#ifdef CONFIG_PPC_EARLY_DEBUG_USBGECKO
SYM_FUNC_START_LOCAL(setup_usbgecko_bat)
/* prepare a BAT for early io */
#if defined(CONFIG_GAMECUBE)
lis r8, 0x0c00
#elif defined(CONFIG_WII)
lis r8, 0x0d00
#else
#error Invalid platform for USB Gecko based early debugging.
#endif
/*
* The virtual address used must match the virtual address
* associated to the fixmap entry FIX_EARLY_DEBUG_BASE.
*/
lis r11, 0xfffe /* top 128K */
ori r8, r8, 0x002a /* uncached, guarded ,rw */
ori r11, r11, 0x2 /* 128K, Vs=1, Vp=0 */
mtspr SPRN_DBAT1L, r8
mtspr SPRN_DBAT1U, r11
blr
SYM_FUNC_END(setup_usbgecko_bat)
#endif
.data