blob: 3da6112fbe39dbb02200f74b4fe8dccba55644e2 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-only
/*
*
* Copyright (c) 2011, The Linux Foundation. All rights reserved.
*/
#include <linux/of.h>
#include <linux/of_dma.h>
#include <linux/bitops.h>
#include <linux/mmc/host.h>
#include <linux/mmc/card.h>
#include "mmci.h"
/* Registers */
#define DML_CONFIG 0x00
#define PRODUCER_CRCI_MSK GENMASK(1, 0)
#define PRODUCER_CRCI_DISABLE 0
#define PRODUCER_CRCI_X_SEL BIT(0)
#define PRODUCER_CRCI_Y_SEL BIT(1)
#define CONSUMER_CRCI_MSK GENMASK(3, 2)
#define CONSUMER_CRCI_DISABLE 0
#define CONSUMER_CRCI_X_SEL BIT(2)
#define CONSUMER_CRCI_Y_SEL BIT(3)
#define PRODUCER_TRANS_END_EN BIT(4)
#define BYPASS BIT(16)
#define DIRECT_MODE BIT(17)
#define INFINITE_CONS_TRANS BIT(18)
#define DML_SW_RESET 0x08
#define DML_PRODUCER_START 0x0c
#define DML_CONSUMER_START 0x10
#define DML_PRODUCER_PIPE_LOGICAL_SIZE 0x14
#define DML_CONSUMER_PIPE_LOGICAL_SIZE 0x18
#define DML_PIPE_ID 0x1c
#define PRODUCER_PIPE_ID_SHFT 0
#define PRODUCER_PIPE_ID_MSK GENMASK(4, 0)
#define CONSUMER_PIPE_ID_SHFT 16
#define CONSUMER_PIPE_ID_MSK GENMASK(20, 16)
#define DML_PRODUCER_BAM_BLOCK_SIZE 0x24
#define DML_PRODUCER_BAM_TRANS_SIZE 0x28
/* other definitions */
#define PRODUCER_PIPE_LOGICAL_SIZE 4096
#define CONSUMER_PIPE_LOGICAL_SIZE 4096
#define DML_OFFSET 0x800
static int qcom_dma_start(struct mmci_host *host, unsigned int *datactrl)
{
u32 config;
void __iomem *base = host->base + DML_OFFSET;
struct mmc_data *data = host->data;
int ret = mmci_dmae_start(host, datactrl);
if (ret)
return ret;
if (data->flags & MMC_DATA_READ) {
/* Read operation: configure DML for producer operation */
/* Set producer CRCI-x and disable consumer CRCI */
config = readl_relaxed(base + DML_CONFIG);
config = (config & ~PRODUCER_CRCI_MSK) | PRODUCER_CRCI_X_SEL;
config = (config & ~CONSUMER_CRCI_MSK) | CONSUMER_CRCI_DISABLE;
writel_relaxed(config, base + DML_CONFIG);
/* Set the Producer BAM block size */
writel_relaxed(data->blksz, base + DML_PRODUCER_BAM_BLOCK_SIZE);
/* Set Producer BAM Transaction size */
writel_relaxed(data->blocks * data->blksz,
base + DML_PRODUCER_BAM_TRANS_SIZE);
/* Set Producer Transaction End bit */
config = readl_relaxed(base + DML_CONFIG);
config |= PRODUCER_TRANS_END_EN;
writel_relaxed(config, base + DML_CONFIG);
/* Trigger producer */
writel_relaxed(1, base + DML_PRODUCER_START);
} else {
/* Write operation: configure DML for consumer operation */
/* Set consumer CRCI-x and disable producer CRCI*/
config = readl_relaxed(base + DML_CONFIG);
config = (config & ~CONSUMER_CRCI_MSK) | CONSUMER_CRCI_X_SEL;
config = (config & ~PRODUCER_CRCI_MSK) | PRODUCER_CRCI_DISABLE;
writel_relaxed(config, base + DML_CONFIG);
/* Clear Producer Transaction End bit */
config = readl_relaxed(base + DML_CONFIG);
config &= ~PRODUCER_TRANS_END_EN;
writel_relaxed(config, base + DML_CONFIG);
/* Trigger consumer */
writel_relaxed(1, base + DML_CONSUMER_START);
}
/* make sure the dml is configured before dma is triggered */
wmb();
return 0;
}
static int of_get_dml_pipe_index(struct device_node *np, const char *name)
{
int index;
struct of_phandle_args dma_spec;
index = of_property_match_string(np, "dma-names", name);
if (index < 0)
return -ENODEV;
if (of_parse_phandle_with_args(np, "dmas", "#dma-cells", index,
&dma_spec))
return -ENODEV;
if (dma_spec.args_count)
return dma_spec.args[0];
return -ENODEV;
}
/* Initialize the dml hardware connected to SD Card controller */
static int qcom_dma_setup(struct mmci_host *host)
{
u32 config;
void __iomem *base;
int consumer_id, producer_id;
struct device_node *np = host->mmc->parent->of_node;
if (mmci_dmae_setup(host))
return -EINVAL;
consumer_id = of_get_dml_pipe_index(np, "tx");
producer_id = of_get_dml_pipe_index(np, "rx");
if (producer_id < 0 || consumer_id < 0) {
mmci_dmae_release(host);
return -EINVAL;
}
base = host->base + DML_OFFSET;
/* Reset the DML block */
writel_relaxed(1, base + DML_SW_RESET);
/* Disable the producer and consumer CRCI */
config = (PRODUCER_CRCI_DISABLE | CONSUMER_CRCI_DISABLE);
/*
* Disable the bypass mode. Bypass mode will only be used
* if data transfer is to happen in PIO mode and don't
* want the BAM interface to connect with SDCC-DML.
*/
config &= ~BYPASS;
/*
* Disable direct mode as we don't DML to MASTER the AHB bus.
* BAM connected with DML should MASTER the AHB bus.
*/
config &= ~DIRECT_MODE;
/*
* Disable infinite mode transfer as we won't be doing any
* infinite size data transfers. All data transfer will be
* of finite data size.
*/
config &= ~INFINITE_CONS_TRANS;
writel_relaxed(config, base + DML_CONFIG);
/*
* Initialize the logical BAM pipe size for producer
* and consumer.
*/
writel_relaxed(PRODUCER_PIPE_LOGICAL_SIZE,
base + DML_PRODUCER_PIPE_LOGICAL_SIZE);
writel_relaxed(CONSUMER_PIPE_LOGICAL_SIZE,
base + DML_CONSUMER_PIPE_LOGICAL_SIZE);
/* Initialize Producer/consumer pipe id */
writel_relaxed(producer_id | (consumer_id << CONSUMER_PIPE_ID_SHFT),
base + DML_PIPE_ID);
/* Make sure dml initialization is finished */
mb();
return 0;
}
static u32 qcom_get_dctrl_cfg(struct mmci_host *host)
{
return MCI_DPSM_ENABLE | (host->data->blksz << 4);
}
static struct mmci_host_ops qcom_variant_ops = {
.prep_data = mmci_dmae_prep_data,
.unprep_data = mmci_dmae_unprep_data,
.get_datactrl_cfg = qcom_get_dctrl_cfg,
.get_next_data = mmci_dmae_get_next_data,
.dma_setup = qcom_dma_setup,
.dma_release = mmci_dmae_release,
.dma_start = qcom_dma_start,
.dma_finalize = mmci_dmae_finalize,
.dma_error = mmci_dmae_error,
};
void qcom_variant_init(struct mmci_host *host)
{
host->ops = &qcom_variant_ops;
}