| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Definitions for MCT (Magic Control Technology) USB-RS232 Converter Driver |
| * |
| * Copyright (C) 2000 Wolfgang Grandegger (wolfgang@ces.ch) |
| * |
| * This driver is for the device MCT USB-RS232 Converter (25 pin, Model No. |
| * U232-P25) from Magic Control Technology Corp. (there is also a 9 pin |
| * Model No. U232-P9). See http://www.mct.com.tw/products/product_us232.html |
| * for further information. The properties of this device are listed at the end |
| * of this file. This device was used in the Dlink DSB-S25. |
| * |
| * All of the information about the device was acquired by using SniffUSB |
| * on Windows98. The technical details of the reverse engineering are |
| * summarized at the end of this file. |
| */ |
| |
| #ifndef __LINUX_USB_SERIAL_MCT_U232_H |
| #define __LINUX_USB_SERIAL_MCT_U232_H |
| |
| #define MCT_U232_VID 0x0711 /* Vendor Id */ |
| #define MCT_U232_PID 0x0210 /* Original MCT Product Id */ |
| |
| /* U232-P25, Sitecom */ |
| #define MCT_U232_SITECOM_PID 0x0230 /* Sitecom Product Id */ |
| |
| /* DU-H3SP USB BAY hub */ |
| #define MCT_U232_DU_H3SP_PID 0x0200 /* D-Link DU-H3SP USB BAY */ |
| |
| /* Belkin badge the MCT U232-P9 as the F5U109 */ |
| #define MCT_U232_BELKIN_F5U109_VID 0x050d /* Vendor Id */ |
| #define MCT_U232_BELKIN_F5U109_PID 0x0109 /* Product Id */ |
| |
| /* |
| * Vendor Request Interface |
| */ |
| #define MCT_U232_SET_REQUEST_TYPE 0x40 |
| #define MCT_U232_GET_REQUEST_TYPE 0xc0 |
| |
| /* Get Modem Status Register (MSR) */ |
| #define MCT_U232_GET_MODEM_STAT_REQUEST 2 |
| #define MCT_U232_GET_MODEM_STAT_SIZE 1 |
| |
| /* Get Line Control Register (LCR) */ |
| /* ... not used by this driver */ |
| #define MCT_U232_GET_LINE_CTRL_REQUEST 6 |
| #define MCT_U232_GET_LINE_CTRL_SIZE 1 |
| |
| /* Set Baud Rate Divisor */ |
| #define MCT_U232_SET_BAUD_RATE_REQUEST 5 |
| #define MCT_U232_SET_BAUD_RATE_SIZE 4 |
| |
| /* Set Line Control Register (LCR) */ |
| #define MCT_U232_SET_LINE_CTRL_REQUEST 7 |
| #define MCT_U232_SET_LINE_CTRL_SIZE 1 |
| |
| /* Set Modem Control Register (MCR) */ |
| #define MCT_U232_SET_MODEM_CTRL_REQUEST 10 |
| #define MCT_U232_SET_MODEM_CTRL_SIZE 1 |
| |
| /* |
| * This USB device request code is not well understood. It is transmitted by |
| * the MCT-supplied Windows driver whenever the baud rate changes. |
| */ |
| #define MCT_U232_SET_UNKNOWN1_REQUEST 11 /* Unknown functionality */ |
| #define MCT_U232_SET_UNKNOWN1_SIZE 1 |
| |
| /* |
| * This USB device request code appears to control whether CTS is required |
| * during transmission. |
| * |
| * Sending a zero byte allows data transmission to a device which is not |
| * asserting CTS. Sending a '1' byte will cause transmission to be deferred |
| * until the device asserts CTS. |
| */ |
| #define MCT_U232_SET_CTS_REQUEST 12 |
| #define MCT_U232_SET_CTS_SIZE 1 |
| |
| #define MCT_U232_MAX_SIZE 4 /* of MCT_XXX_SIZE */ |
| |
| /* |
| * Baud rate (divisor) |
| * Actually, there are two of them, MCT website calls them "Philips solution" |
| * and "Intel solution". They are the regular MCT and "Sitecom" for us. |
| * This is pointless to document in the header, see the code for the bits. |
| */ |
| static int mct_u232_calculate_baud_rate(struct usb_serial *serial, |
| speed_t value, speed_t *result); |
| |
| /* |
| * Line Control Register (LCR) |
| */ |
| #define MCT_U232_SET_BREAK 0x40 |
| |
| #define MCT_U232_PARITY_SPACE 0x38 |
| #define MCT_U232_PARITY_MARK 0x28 |
| #define MCT_U232_PARITY_EVEN 0x18 |
| #define MCT_U232_PARITY_ODD 0x08 |
| #define MCT_U232_PARITY_NONE 0x00 |
| |
| #define MCT_U232_DATA_BITS_5 0x00 |
| #define MCT_U232_DATA_BITS_6 0x01 |
| #define MCT_U232_DATA_BITS_7 0x02 |
| #define MCT_U232_DATA_BITS_8 0x03 |
| |
| #define MCT_U232_STOP_BITS_2 0x04 |
| #define MCT_U232_STOP_BITS_1 0x00 |
| |
| /* |
| * Modem Control Register (MCR) |
| */ |
| #define MCT_U232_MCR_NONE 0x8 /* Deactivate DTR and RTS */ |
| #define MCT_U232_MCR_RTS 0xa /* Activate RTS */ |
| #define MCT_U232_MCR_DTR 0x9 /* Activate DTR */ |
| |
| /* |
| * Modem Status Register (MSR) |
| */ |
| #define MCT_U232_MSR_INDEX 0x0 /* data[index] */ |
| #define MCT_U232_MSR_CD 0x80 /* Current CD */ |
| #define MCT_U232_MSR_RI 0x40 /* Current RI */ |
| #define MCT_U232_MSR_DSR 0x20 /* Current DSR */ |
| #define MCT_U232_MSR_CTS 0x10 /* Current CTS */ |
| #define MCT_U232_MSR_DCD 0x08 /* Delta CD */ |
| #define MCT_U232_MSR_DRI 0x04 /* Delta RI */ |
| #define MCT_U232_MSR_DDSR 0x02 /* Delta DSR */ |
| #define MCT_U232_MSR_DCTS 0x01 /* Delta CTS */ |
| |
| /* |
| * Line Status Register (LSR) |
| */ |
| #define MCT_U232_LSR_INDEX 1 /* data[index] */ |
| #define MCT_U232_LSR_ERR 0x80 /* OE | PE | FE | BI */ |
| #define MCT_U232_LSR_TEMT 0x40 /* transmit register empty */ |
| #define MCT_U232_LSR_THRE 0x20 /* transmit holding register empty */ |
| #define MCT_U232_LSR_BI 0x10 /* break indicator */ |
| #define MCT_U232_LSR_FE 0x08 /* framing error */ |
| #define MCT_U232_LSR_OE 0x02 /* overrun error */ |
| #define MCT_U232_LSR_PE 0x04 /* parity error */ |
| #define MCT_U232_LSR_OE 0x02 /* overrun error */ |
| #define MCT_U232_LSR_DR 0x01 /* receive data ready */ |
| |
| |
| /* ----------------------------------------------------------------------------- |
| * Technical Specification reverse engineered with SniffUSB on Windows98 |
| * ===================================================================== |
| * |
| * The technical details of the device have been acquired be using "SniffUSB" |
| * and the vendor-supplied device driver (version 2.3A) under Windows98. To |
| * identify the USB vendor-specific requests and to assign them to terminal |
| * settings (flow control, baud rate, etc.) the program "SerialSettings" from |
| * William G. Greathouse has been proven to be very useful. I also used the |
| * Win98 "HyperTerminal" and "usb-robot" on Linux for testing. The results and |
| * observations are summarized below: |
| * |
| * The USB requests seem to be directly mapped to the registers of a 8250, |
| * 16450 or 16550 UART. The FreeBSD handbook (appendix F.4 "Input/Output |
| * devices") contains a comprehensive description of UARTs and its registers. |
| * The bit descriptions are actually taken from there. |
| * |
| * |
| * Baud rate (divisor) |
| * ------------------- |
| * |
| * BmRequestType: 0x40 (0100 0000B) |
| * bRequest: 0x05 |
| * wValue: 0x0000 |
| * wIndex: 0x0000 |
| * wLength: 0x0004 |
| * Data: divisor = 115200 / baud_rate |
| * |
| * SniffUSB observations (Nov 2003): Contrary to the 'wLength' value of 4 |
| * shown above, observations with a Belkin F5U109 adapter, using the |
| * MCT-supplied Windows98 driver (U2SPORT.VXD, "File version: 1.21P.0104 for |
| * Win98/Me"), show this request has a length of 1 byte, presumably because |
| * of the fact that the Belkin adapter and the 'Sitecom U232-P25' adapter |
| * use a baud-rate code instead of a conventional RS-232 baud rate divisor. |
| * The current source code for this driver does not reflect this fact, but |
| * the driver works fine with this adapter/driver combination nonetheless. |
| * |
| * |
| * Line Control Register (LCR) |
| * --------------------------- |
| * |
| * BmRequestType: 0x40 (0100 0000B) 0xc0 (1100 0000B) |
| * bRequest: 0x07 0x06 |
| * wValue: 0x0000 |
| * wIndex: 0x0000 |
| * wLength: 0x0001 |
| * Data: LCR (see below) |
| * |
| * Bit 7: Divisor Latch Access Bit (DLAB). When set, access to the data |
| * transmit/receive register (THR/RBR) and the Interrupt Enable Register |
| * (IER) is disabled. Any access to these ports is now redirected to the |
| * Divisor Latch Registers. Setting this bit, loading the Divisor |
| * Registers, and clearing DLAB should be done with interrupts disabled. |
| * Bit 6: Set Break. When set to "1", the transmitter begins to transmit |
| * continuous Spacing until this bit is set to "0". This overrides any |
| * bits of characters that are being transmitted. |
| * Bit 5: Stick Parity. When parity is enabled, setting this bit causes parity |
| * to always be "1" or "0", based on the value of Bit 4. |
| * Bit 4: Even Parity Select (EPS). When parity is enabled and Bit 5 is "0", |
| * setting this bit causes even parity to be transmitted and expected. |
| * Otherwise, odd parity is used. |
| * Bit 3: Parity Enable (PEN). When set to "1", a parity bit is inserted |
| * between the last bit of the data and the Stop Bit. The UART will also |
| * expect parity to be present in the received data. |
| * Bit 2: Number of Stop Bits (STB). If set to "1" and using 5-bit data words, |
| * 1.5 Stop Bits are transmitted and expected in each data word. For |
| * 6, 7 and 8-bit data words, 2 Stop Bits are transmitted and expected. |
| * When this bit is set to "0", one Stop Bit is used on each data word. |
| * Bit 1: Word Length Select Bit #1 (WLSB1) |
| * Bit 0: Word Length Select Bit #0 (WLSB0) |
| * Together these bits specify the number of bits in each data word. |
| * 1 0 Word Length |
| * 0 0 5 Data Bits |
| * 0 1 6 Data Bits |
| * 1 0 7 Data Bits |
| * 1 1 8 Data Bits |
| * |
| * SniffUSB observations: Bit 7 seems not to be used. There seem to be two bugs |
| * in the Win98 driver: the break does not work (bit 6 is not asserted) and the |
| * stick parity bit is not cleared when set once. The LCR can also be read |
| * back with USB request 6 but this has never been observed with SniffUSB. |
| * |
| * |
| * Modem Control Register (MCR) |
| * ---------------------------- |
| * |
| * BmRequestType: 0x40 (0100 0000B) |
| * bRequest: 0x0a |
| * wValue: 0x0000 |
| * wIndex: 0x0000 |
| * wLength: 0x0001 |
| * Data: MCR (Bit 4..7, see below) |
| * |
| * Bit 7: Reserved, always 0. |
| * Bit 6: Reserved, always 0. |
| * Bit 5: Reserved, always 0. |
| * Bit 4: Loop-Back Enable. When set to "1", the UART transmitter and receiver |
| * are internally connected together to allow diagnostic operations. In |
| * addition, the UART modem control outputs are connected to the UART |
| * modem control inputs. CTS is connected to RTS, DTR is connected to |
| * DSR, OUT1 is connected to RI, and OUT 2 is connected to DCD. |
| * Bit 3: OUT 2. An auxiliary output that the host processor may set high or |
| * low. In the IBM PC serial adapter (and most clones), OUT 2 is used |
| * to tri-state (disable) the interrupt signal from the |
| * 8250/16450/16550 UART. |
| * Bit 2: OUT 1. An auxiliary output that the host processor may set high or |
| * low. This output is not used on the IBM PC serial adapter. |
| * Bit 1: Request to Send (RTS). When set to "1", the output of the UART -RTS |
| * line is Low (Active). |
| * Bit 0: Data Terminal Ready (DTR). When set to "1", the output of the UART |
| * -DTR line is Low (Active). |
| * |
| * SniffUSB observations: Bit 2 and 4 seem not to be used but bit 3 has been |
| * seen _always_ set. |
| * |
| * |
| * Modem Status Register (MSR) |
| * --------------------------- |
| * |
| * BmRequestType: 0xc0 (1100 0000B) |
| * bRequest: 0x02 |
| * wValue: 0x0000 |
| * wIndex: 0x0000 |
| * wLength: 0x0001 |
| * Data: MSR (see below) |
| * |
| * Bit 7: Data Carrier Detect (CD). Reflects the state of the DCD line on the |
| * UART. |
| * Bit 6: Ring Indicator (RI). Reflects the state of the RI line on the UART. |
| * Bit 5: Data Set Ready (DSR). Reflects the state of the DSR line on the UART. |
| * Bit 4: Clear To Send (CTS). Reflects the state of the CTS line on the UART. |
| * Bit 3: Delta Data Carrier Detect (DDCD). Set to "1" if the -DCD line has |
| * changed state one more more times since the last time the MSR was |
| * read by the host. |
| * Bit 2: Trailing Edge Ring Indicator (TERI). Set to "1" if the -RI line has |
| * had a low to high transition since the last time the MSR was read by |
| * the host. |
| * Bit 1: Delta Data Set Ready (DDSR). Set to "1" if the -DSR line has changed |
| * state one more more times since the last time the MSR was read by the |
| * host. |
| * Bit 0: Delta Clear To Send (DCTS). Set to "1" if the -CTS line has changed |
| * state one more times since the last time the MSR was read by the |
| * host. |
| * |
| * SniffUSB observations: the MSR is also returned as first byte on the |
| * interrupt-in endpoint 0x83 to signal changes of modem status lines. The USB |
| * request to read MSR cannot be applied during normal device operation. |
| * |
| * |
| * Line Status Register (LSR) |
| * -------------------------- |
| * |
| * Bit 7 Error in Receiver FIFO. On the 8250/16450 UART, this bit is zero. |
| * This bit is set to "1" when any of the bytes in the FIFO have one |
| * or more of the following error conditions: PE, FE, or BI. |
| * Bit 6 Transmitter Empty (TEMT). When set to "1", there are no words |
| * remaining in the transmit FIFO or the transmit shift register. The |
| * transmitter is completely idle. |
| * Bit 5 Transmitter Holding Register Empty (THRE). When set to "1", the |
| * FIFO (or holding register) now has room for at least one additional |
| * word to transmit. The transmitter may still be transmitting when |
| * this bit is set to "1". |
| * Bit 4 Break Interrupt (BI). The receiver has detected a Break signal. |
| * Bit 3 Framing Error (FE). A Start Bit was detected but the Stop Bit did |
| * not appear at the expected time. The received word is probably |
| * garbled. |
| * Bit 2 Parity Error (PE). The parity bit was incorrect for the word |
| * received. |
| * Bit 1 Overrun Error (OE). A new word was received and there was no room |
| * in the receive buffer. The newly-arrived word in the shift register |
| * is discarded. On 8250/16450 UARTs, the word in the holding register |
| * is discarded and the newly- arrived word is put in the holding |
| * register. |
| * Bit 0 Data Ready (DR). One or more words are in the receive FIFO that the |
| * host may read. A word must be completely received and moved from |
| * the shift register into the FIFO (or holding register for |
| * 8250/16450 designs) before this bit is set. |
| * |
| * SniffUSB observations: the LSR is returned as second byte on the |
| * interrupt-in endpoint 0x83 to signal error conditions. Such errors have |
| * been seen with minicom/zmodem transfers (CRC errors). |
| * |
| * |
| * Unknown #1 |
| * ------------------- |
| * |
| * BmRequestType: 0x40 (0100 0000B) |
| * bRequest: 0x0b |
| * wValue: 0x0000 |
| * wIndex: 0x0000 |
| * wLength: 0x0001 |
| * Data: 0x00 |
| * |
| * SniffUSB observations (Nov 2003): With the MCT-supplied Windows98 driver |
| * (U2SPORT.VXD, "File version: 1.21P.0104 for Win98/Me"), this request |
| * occurs immediately after a "Baud rate (divisor)" message. It was not |
| * observed at any other time. It is unclear what purpose this message |
| * serves. |
| * |
| * |
| * Unknown #2 |
| * ------------------- |
| * |
| * BmRequestType: 0x40 (0100 0000B) |
| * bRequest: 0x0c |
| * wValue: 0x0000 |
| * wIndex: 0x0000 |
| * wLength: 0x0001 |
| * Data: 0x00 |
| * |
| * SniffUSB observations (Nov 2003): With the MCT-supplied Windows98 driver |
| * (U2SPORT.VXD, "File version: 1.21P.0104 for Win98/Me"), this request |
| * occurs immediately after the 'Unknown #1' message (see above). It was |
| * not observed at any other time. It is unclear what other purpose (if |
| * any) this message might serve, but without it, the USB/RS-232 adapter |
| * will not write to RS-232 devices which do not assert the 'CTS' signal. |
| * |
| * |
| * Flow control |
| * ------------ |
| * |
| * SniffUSB observations: no flow control specific requests have been realized |
| * apart from DTR/RTS settings. Both signals are dropped for no flow control |
| * but asserted for hardware or software flow control. |
| * |
| * |
| * Endpoint usage |
| * -------------- |
| * |
| * SniffUSB observations: the bulk-out endpoint 0x1 and interrupt-in endpoint |
| * 0x81 is used to transmit and receive characters. The second interrupt-in |
| * endpoint 0x83 signals exceptional conditions like modem line changes and |
| * errors. The first byte returned is the MSR and the second byte the LSR. |
| * |
| * |
| * Other observations |
| * ------------------ |
| * |
| * Queued bulk transfers like used in visor.c did not work. |
| * |
| * |
| * Properties of the USB device used (as found in /var/log/messages) |
| * ----------------------------------------------------------------- |
| * |
| * Manufacturer: MCT Corporation. |
| * Product: USB-232 Interfact Controller |
| * SerialNumber: U2S22050 |
| * |
| * Length = 18 |
| * DescriptorType = 01 |
| * USB version = 1.00 |
| * Vendor:Product = 0711:0210 |
| * MaxPacketSize0 = 8 |
| * NumConfigurations = 1 |
| * Device version = 1.02 |
| * Device Class:SubClass:Protocol = 00:00:00 |
| * Per-interface classes |
| * Configuration: |
| * bLength = 9 |
| * bDescriptorType = 02 |
| * wTotalLength = 0027 |
| * bNumInterfaces = 01 |
| * bConfigurationValue = 01 |
| * iConfiguration = 00 |
| * bmAttributes = c0 |
| * MaxPower = 100mA |
| * |
| * Interface: 0 |
| * Alternate Setting: 0 |
| * bLength = 9 |
| * bDescriptorType = 04 |
| * bInterfaceNumber = 00 |
| * bAlternateSetting = 00 |
| * bNumEndpoints = 03 |
| * bInterface Class:SubClass:Protocol = 00:00:00 |
| * iInterface = 00 |
| * Endpoint: |
| * bLength = 7 |
| * bDescriptorType = 05 |
| * bEndpointAddress = 81 (in) |
| * bmAttributes = 03 (Interrupt) |
| * wMaxPacketSize = 0040 |
| * bInterval = 02 |
| * Endpoint: |
| * bLength = 7 |
| * bDescriptorType = 05 |
| * bEndpointAddress = 01 (out) |
| * bmAttributes = 02 (Bulk) |
| * wMaxPacketSize = 0040 |
| * bInterval = 00 |
| * Endpoint: |
| * bLength = 7 |
| * bDescriptorType = 05 |
| * bEndpointAddress = 83 (in) |
| * bmAttributes = 03 (Interrupt) |
| * wMaxPacketSize = 0002 |
| * bInterval = 02 |
| * |
| * |
| * Hardware details (added by Martin Hamilton, 2001/12/06) |
| * ----------------------------------------------------------------- |
| * |
| * This info was gleaned from opening a Belkin F5U109 DB9 USB serial |
| * adaptor, which turns out to simply be a re-badged U232-P9. We |
| * know this because there is a sticky label on the circuit board |
| * which says "U232-P9" ;-) |
| * |
| * The circuit board inside the adaptor contains a Philips PDIUSBD12 |
| * USB endpoint chip and a Philips P87C52UBAA microcontroller with |
| * embedded UART. Exhaustive documentation for these is available at: |
| * |
| * http://www.semiconductors.philips.com/pip/p87c52ubaa |
| * http://www.nxp.com/acrobat_download/various/PDIUSBD12_PROGRAMMING_GUIDE.pdf |
| * |
| * Thanks to Julian Highfield for the pointer to the Philips database. |
| * |
| */ |
| |
| #endif /* __LINUX_USB_SERIAL_MCT_U232_H */ |
| |
