| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2021, The Linux Foundation. All rights reserved. |
| * Copyright (c) 2022, Linaro Limited |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> |
| #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h> |
| #include <dt-bindings/input/gpio-keys.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| |
| #include "sc8280xp.dtsi" |
| #include "sc8280xp-pmics.dtsi" |
| |
| / { |
| model = "Lenovo ThinkPad X13s"; |
| compatible = "lenovo,thinkpad-x13s", "qcom,sc8280xp"; |
| |
| aliases { |
| i2c4 = &i2c4; |
| i2c21 = &i2c21; |
| serial1 = &uart2; |
| }; |
| |
| wcd938x: audio-codec { |
| compatible = "qcom,wcd9380-codec"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wcd_default>; |
| |
| reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>; |
| |
| vdd-buck-supply = <&vreg_s10b>; |
| vdd-rxtx-supply = <&vreg_s10b>; |
| vdd-io-supply = <&vreg_s10b>; |
| vdd-mic-bias-supply = <&vreg_bob>; |
| |
| qcom,micbias1-microvolt = <1800000>; |
| qcom,micbias2-microvolt = <1800000>; |
| qcom,micbias3-microvolt = <1800000>; |
| qcom,micbias4-microvolt = <1800000>; |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| qcom,rx-device = <&wcd_rx>; |
| qcom,tx-device = <&wcd_tx>; |
| |
| #sound-dai-cells = <1>; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&pmc8280c_lpg 3 1000000>; |
| enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>; |
| power-supply = <&vreg_edp_bl>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hall_int_n_default>; |
| |
| switch-lid { |
| gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| wakeup-source; |
| wakeup-event-action = <EV_ACT_DEASSERTED>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| led-camera-indicator { |
| label = "white:camera-indicator"; |
| function = LED_FUNCTION_INDICATOR; |
| color = <LED_COLOR_ID_WHITE>; |
| gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "none"; |
| default-state = "off"; |
| /* Reuse as a panic indicator until we get a "camera on" trigger */ |
| panic-indicator; |
| }; |
| }; |
| |
| pmic-glink { |
| compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| connector@0 { |
| compatible = "usb-c-connector"; |
| reg = <0>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_con0_hs: endpoint { |
| remote-endpoint = <&usb_0_role_switch>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_con0_ss: endpoint { |
| remote-endpoint = <&usb_0_qmpphy_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| pmic_glink_con0_sbu: endpoint { |
| remote-endpoint = <&usb0_sbu_mux>; |
| }; |
| }; |
| }; |
| }; |
| |
| connector@1 { |
| compatible = "usb-c-connector"; |
| reg = <1>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_con1_hs: endpoint { |
| remote-endpoint = <&usb_1_role_switch>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_con1_ss: endpoint { |
| remote-endpoint = <&usb_1_qmpphy_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| pmic_glink_con1_sbu: endpoint { |
| remote-endpoint = <&usb1_sbu_mux>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| vreg_edp_3p3: regulator-edp-3p3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VCC3LCD"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&edp_reg_en>; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_edp_bl: regulator-edp-bl { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VBL9"; |
| regulator-min-microvolt = <3600000>; |
| regulator-max-microvolt = <3600000>; |
| |
| gpio = <&pmc8280_1_gpios 9 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&edp_bl_reg_en>; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_misc_3p3: regulator-misc-3p3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VCC3B"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&pmc8280_1_gpios 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&misc_3p3_reg_en>; |
| |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vreg_nvme: regulator-nvme { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VCC3_SSD"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 135 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&nvme_reg_en>; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_vph_pwr: regulator-vph-pwr { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VPH_VCC3R9"; |
| regulator-min-microvolt = <3900000>; |
| regulator-max-microvolt = <3900000>; |
| |
| regulator-always-on; |
| }; |
| |
| vreg_wlan: regulator-wlan { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VCC_WLAN_3R9"; |
| regulator-min-microvolt = <3900000>; |
| regulator-max-microvolt = <3900000>; |
| |
| gpio = <&pmr735a_gpios 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hastings_reg_en>; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_wwan: regulator-wwan { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VCC3B_WAN"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&pmc8280_2_gpios 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wwan_sw_en>; |
| |
| regulator-boot-on; |
| }; |
| |
| reserved-memory { |
| gpu_mem: gpu-mem@8bf00000 { |
| reg = <0 0x8bf00000 0 0x2000>; |
| no-map; |
| }; |
| |
| linux,cma { |
| compatible = "shared-dma-pool"; |
| size = <0x0 0x8000000>; |
| reusable; |
| linux,cma-default; |
| }; |
| }; |
| |
| thermal-zones { |
| skin-temp-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <0>; |
| thermal-sensors = <&pmk8280_adc_tm 5>; |
| |
| trips { |
| skin_temp_alert0: trip-point0 { |
| temperature = <55000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| skin_temp_alert1: trip-point1 { |
| temperature = <58000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| |
| skin-temp-crit { |
| temperature = <73000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&skin_temp_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| |
| map1 { |
| trip = <&skin_temp_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| }; |
| |
| usb0-sbu-mux { |
| compatible = "pericom,pi3usb102", "gpio-sbu-mux"; |
| |
| enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>; |
| select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb0_sbu_default>; |
| |
| mode-switch; |
| orientation-switch; |
| |
| port { |
| usb0_sbu_mux: endpoint { |
| remote-endpoint = <&pmic_glink_con0_sbu>; |
| }; |
| }; |
| }; |
| |
| usb1-sbu-mux { |
| compatible = "pericom,pi3usb102", "gpio-sbu-mux"; |
| |
| enable-gpios = <&tlmm 48 GPIO_ACTIVE_LOW>; |
| select-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb1_sbu_default>; |
| |
| mode-switch; |
| orientation-switch; |
| |
| port { |
| usb1_sbu_mux: endpoint { |
| remote-endpoint = <&pmic_glink_con1_sbu>; |
| }; |
| }; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8350-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| vdd-l1-l4-supply = <&vreg_s12b>; |
| vdd-l2-l7-supply = <&vreg_bob>; |
| vdd-l3-l5-supply = <&vreg_s11b>; |
| vdd-l6-l9-l10-supply = <&vreg_s12b>; |
| vdd-l8-supply = <&vreg_s12b>; |
| |
| vreg_s10b: smps10 { |
| regulator-name = "vreg_s10b"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_s11b: smps11 { |
| regulator-name = "vreg_s11b"; |
| regulator-min-microvolt = <1272000>; |
| regulator-max-microvolt = <1272000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_s12b: smps12 { |
| regulator-name = "vreg_s12b"; |
| regulator-min-microvolt = <984000>; |
| regulator-max-microvolt = <984000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_l3b: ldo3 { |
| regulator-name = "vreg_l3b"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-boot-on; |
| }; |
| |
| vreg_l4b: ldo4 { |
| regulator-name = "vreg_l4b"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6b: ldo6 { |
| regulator-name = "vreg_l6b"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-boot-on; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8350c-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-bob-supply = <&vreg_vph_pwr>; |
| vdd-l1-l12-supply = <&vreg_s1c>; |
| vdd-l2-l8-supply = <&vreg_s1c>; |
| vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>; |
| vdd-l6-l9-l11-supply = <&vreg_bob>; |
| vdd-l10-supply = <&vreg_s11b>; |
| |
| vreg_s1c: smps1 { |
| regulator-name = "vreg_s1c"; |
| regulator-min-microvolt = <1880000>; |
| regulator-max-microvolt = <1900000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_l1c: ldo1 { |
| regulator-name = "vreg_l1c"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12c: ldo12 { |
| regulator-name = "vreg_l12c"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13c: ldo13 { |
| regulator-name = "vreg_l13c"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob: bob { |
| regulator-name = "vreg_bob"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; |
| regulator-always-on; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pm8350-rpmh-regulators"; |
| qcom,pmic-id = "d"; |
| |
| vdd-l1-l4-supply = <&vreg_s11b>; |
| vdd-l2-l7-supply = <&vreg_bob>; |
| vdd-l3-l5-supply = <&vreg_s11b>; |
| vdd-l6-l9-l10-supply = <&vreg_s12b>; |
| vdd-l8-supply = <&vreg_s12b>; |
| |
| vreg_l3d: ldo3 { |
| regulator-name = "vreg_l3d"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4d: ldo4 { |
| regulator-name = "vreg_l4d"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6d: ldo6 { |
| regulator-name = "vreg_l6d"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7d: ldo7 { |
| regulator-name = "vreg_l7d"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9d: ldo9 { |
| regulator-name = "vreg_l9d"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &dispcc0 { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| memory-region = <&gpu_mem>; |
| firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcdxkmsuc8280.mbn"; |
| }; |
| }; |
| |
| &mdss0 { |
| status = "okay"; |
| }; |
| |
| &mdss0_dp0 { |
| status = "okay"; |
| }; |
| |
| &mdss0_dp0_out { |
| data-lanes = <0 1>; |
| remote-endpoint = <&usb_0_qmpphy_dp_in>; |
| }; |
| |
| &mdss0_dp1 { |
| status = "okay"; |
| }; |
| |
| &mdss0_dp1_out { |
| data-lanes = <0 1>; |
| remote-endpoint = <&usb_1_qmpphy_dp_in>; |
| }; |
| |
| &mdss0_dp3 { |
| compatible = "qcom,sc8280xp-edp"; |
| |
| data-lanes = <0 1 2 3>; |
| |
| status = "okay"; |
| |
| aux-bus { |
| panel { |
| compatible = "edp-panel"; |
| |
| backlight = <&backlight>; |
| power-supply = <&vreg_edp_3p3>; |
| |
| port { |
| edp_panel_in: endpoint { |
| remote-endpoint = <&mdss0_dp3_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| mdss0_dp3_out: endpoint { |
| remote-endpoint = <&edp_panel_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss0_dp3_phy { |
| vdda-phy-supply = <&vreg_l6b>; |
| vdda-pll-supply = <&vreg_l3b>; |
| |
| status = "okay"; |
| }; |
| |
| &i2c4 { |
| clock-frequency = <400000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c4_default>; |
| |
| status = "okay"; |
| |
| /* FIXME: verify */ |
| touchscreen@10 { |
| compatible = "hid-over-i2c"; |
| reg = <0x10>; |
| |
| hid-descr-addr = <0x1>; |
| interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>; |
| vdd-supply = <&vreg_misc_3p3>; |
| vddl-supply = <&vreg_s10b>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts0_default>; |
| }; |
| }; |
| |
| &i2c21 { |
| clock-frequency = <400000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c21_default>, <&tpad_default>; |
| |
| status = "okay"; |
| |
| touchpad@15 { |
| compatible = "hid-over-i2c"; |
| reg = <0x15>; |
| |
| hid-descr-addr = <0x1>; |
| interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; |
| vdd-supply = <&vreg_misc_3p3>; |
| vddl-supply = <&vreg_s10b>; |
| |
| wakeup-source; |
| }; |
| |
| touchpad@2c { |
| compatible = "hid-over-i2c"; |
| reg = <0x2c>; |
| |
| hid-descr-addr = <0x20>; |
| interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>; |
| vdd-supply = <&vreg_misc_3p3>; |
| vddl-supply = <&vreg_s10b>; |
| |
| wakeup-source; |
| }; |
| |
| keyboard@68 { |
| compatible = "hid-over-i2c"; |
| reg = <0x68>; |
| |
| hid-descr-addr = <0x1>; |
| interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>; |
| vdd-supply = <&vreg_misc_3p3>; |
| vddl-supply = <&vreg_s10b>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&kybd_default>; |
| |
| wakeup-source; |
| }; |
| }; |
| |
| &pcie2a { |
| perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>; |
| |
| vddpe-3v3-supply = <&vreg_nvme>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie2a_default>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie2a_phy { |
| vdda-phy-supply = <&vreg_l6d>; |
| vdda-pll-supply = <&vreg_l4d>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie3a { |
| perst-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; |
| |
| vddpe-3v3-supply = <&vreg_wwan>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie3a_default>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie3a_phy { |
| vdda-phy-supply = <&vreg_l6d>; |
| vdda-pll-supply = <&vreg_l4d>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie4 { |
| perst-gpios = <&tlmm 141 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 139 GPIO_ACTIVE_LOW>; |
| |
| vddpe-3v3-supply = <&vreg_wlan>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie4_default>; |
| |
| status = "okay"; |
| |
| pcie@0 { |
| device_type = "pci"; |
| reg = <0x0 0x0 0x0 0x0 0x0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges; |
| |
| bus-range = <0x01 0xff>; |
| |
| wifi@0 { |
| compatible = "pci17cb,1103"; |
| reg = <0x10000 0x0 0x0 0x0 0x0>; |
| |
| qcom,ath11k-calibration-variant = "LE_X13S"; |
| }; |
| }; |
| }; |
| |
| &pcie4_phy { |
| vdda-phy-supply = <&vreg_l6d>; |
| vdda-pll-supply = <&vreg_l4d>; |
| |
| status = "okay"; |
| }; |
| |
| &pmc8280c_lpg { |
| status = "okay"; |
| }; |
| |
| &pmk8280_adc_tm { |
| status = "okay"; |
| |
| sys-therm@0 { |
| reg = <0>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>; |
| qcom,hw-settle-time-us = <200>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| }; |
| |
| sys-therm@1 { |
| reg = <1>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>; |
| qcom,hw-settle-time-us = <200>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| }; |
| |
| sys-therm@2 { |
| reg = <2>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>; |
| qcom,hw-settle-time-us = <200>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| }; |
| |
| sys-therm@3 { |
| reg = <3>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>; |
| qcom,hw-settle-time-us = <200>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| }; |
| |
| sys-therm@4 { |
| reg = <4>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(3)>; |
| qcom,hw-settle-time-us = <200>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| }; |
| |
| sys-therm@5 { |
| reg = <5>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(3)>; |
| qcom,hw-settle-time-us = <200>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| }; |
| |
| sys-therm@6 { |
| reg = <6>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(3)>; |
| qcom,hw-settle-time-us = <200>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| }; |
| |
| sys-therm@7 { |
| reg = <7>; |
| io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(3)>; |
| qcom,hw-settle-time-us = <200>; |
| qcom,avg-samples = <2>; |
| qcom,ratiometric; |
| }; |
| }; |
| |
| &pmk8280_pon_pwrkey { |
| status = "okay"; |
| }; |
| |
| &pmk8280_pon_resin { |
| status = "okay"; |
| }; |
| |
| &pmk8280_rtc { |
| nvmem-cells = <&rtc_offset>; |
| nvmem-cell-names = "offset"; |
| |
| status = "okay"; |
| }; |
| |
| &pmk8280_sdam_6 { |
| status = "okay"; |
| |
| rtc_offset: rtc-offset@bc { |
| reg = <0xbc 0x4>; |
| }; |
| }; |
| |
| &pmk8280_vadc { |
| status = "okay"; |
| |
| channel@3 { |
| reg = <PMK8350_ADC7_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| label = "pmk8350_die_temp"; |
| }; |
| |
| channel@44 { |
| reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "pmk8350_xo_therm"; |
| }; |
| |
| channel@103 { |
| reg = <PM8350_ADC7_DIE_TEMP(1)>; |
| qcom,pre-scaling = <1 1>; |
| label = "pmc8280_1_die_temp"; |
| }; |
| |
| channel@144 { |
| reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "sys_therm1"; |
| }; |
| |
| channel@145 { |
| reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "sys_therm2"; |
| }; |
| |
| channel@146 { |
| reg = <PM8350_ADC7_AMUX_THM3_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "sys_therm3"; |
| }; |
| |
| channel@147 { |
| reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "sys_therm4"; |
| }; |
| |
| channel@303 { |
| reg = <PM8350_ADC7_DIE_TEMP(3)>; |
| qcom,pre-scaling = <1 1>; |
| label = "pmc8280_2_die_temp"; |
| }; |
| |
| channel@344 { |
| reg = <PM8350_ADC7_AMUX_THM1_100K_PU(3)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "sys_therm5"; |
| }; |
| |
| channel@345 { |
| reg = <PM8350_ADC7_AMUX_THM2_100K_PU(3)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "sys_therm6"; |
| }; |
| |
| channel@346 { |
| reg = <PM8350_ADC7_AMUX_THM3_100K_PU(3)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "sys_therm7"; |
| }; |
| |
| channel@347 { |
| reg = <PM8350_ADC7_AMUX_THM4_100K_PU(3)>; |
| qcom,hw-settle-time = <200>; |
| qcom,ratiometric; |
| label = "sys_therm8"; |
| }; |
| |
| channel@403 { |
| reg = <PMR735A_ADC7_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| label = "pmr735a_die_temp"; |
| }; |
| }; |
| |
| &qup0 { |
| status = "okay"; |
| }; |
| |
| &qup1 { |
| status = "okay"; |
| }; |
| |
| &qup2 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn"; |
| |
| status = "okay"; |
| }; |
| |
| &remoteproc_nsp0 { |
| firmware-name = "qcom/sc8280xp/LENOVO/21BX/qccdsp8280.mbn"; |
| |
| status = "okay"; |
| }; |
| |
| &rxmacro { |
| status = "okay"; |
| }; |
| |
| &sound { |
| compatible = "qcom,sc8280xp-sndcard"; |
| model = "SC8280XP-LENOVO-X13S"; |
| audio-routing = |
| "SpkrLeft IN", "WSA_SPK1 OUT", |
| "SpkrRight IN", "WSA_SPK2 OUT", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "AMIC2", "MIC BIAS2", |
| "VA DMIC0", "MIC BIAS1", |
| "VA DMIC1", "MIC BIAS1", |
| "VA DMIC2", "MIC BIAS3", |
| "VA DMIC0", "VA MIC BIAS1", |
| "VA DMIC1", "VA MIC BIAS1", |
| "VA DMIC2", "VA MIC BIAS3", |
| "TX SWR_ADC1", "ADC2_OUTPUT"; |
| |
| wcd-playback-dai-link { |
| link-name = "WCD Playback"; |
| cpu { |
| sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wcd-capture-dai-link { |
| link-name = "WCD Capture"; |
| cpu { |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wsa-dai-link { |
| link-name = "WSA Playback"; |
| cpu { |
| sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| va-dai-link { |
| link-name = "VA Capture"; |
| cpu { |
| sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| |
| codec { |
| sound-dai = <&vamacro 0>; |
| }; |
| }; |
| }; |
| |
| &swr0 { |
| status = "okay"; |
| |
| left_spkr: wsa8830-left@0,1 { |
| compatible = "sdw10217020200"; |
| reg = <0 1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spkr_1_sd_n_default>; |
| powerdown-gpios = <&tlmm 178 GPIO_ACTIVE_LOW>; |
| #thermal-sensor-cells = <0>; |
| sound-name-prefix = "SpkrLeft"; |
| #sound-dai-cells = <0>; |
| vdd-supply = <&vreg_s10b>; |
| }; |
| |
| right_spkr: wsa8830-right@0,2 { |
| compatible = "sdw10217020200"; |
| reg = <0 2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spkr_2_sd_n_default>; |
| powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>; |
| #thermal-sensor-cells = <0>; |
| sound-name-prefix = "SpkrRight"; |
| #sound-dai-cells = <0>; |
| vdd-supply = <&vreg_s10b>; |
| }; |
| }; |
| |
| &swr1 { |
| status = "okay"; |
| |
| wcd_rx: wcd9380-rx@0,4 { |
| compatible = "sdw20217010d00"; |
| reg = <0 4>; |
| qcom,rx-port-mapping = <1 2 3 4 5>; |
| }; |
| }; |
| |
| &swr2 { |
| status = "okay"; |
| |
| wcd_tx: wcd9380-tx@0,3 { |
| compatible = "sdw20217010d00"; |
| reg = <0 3>; |
| qcom,tx-port-mapping = <1 1 2 3>; |
| }; |
| }; |
| |
| &txmacro { |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-0 = <&uart2_default>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,wcn6855-bt"; |
| |
| vddio-supply = <&vreg_s10b>; |
| vddbtcxmx-supply = <&vreg_s12b>; |
| vddrfacmn-supply = <&vreg_s12b>; |
| vddrfa0p8-supply = <&vreg_s12b>; |
| vddrfa1p2-supply = <&vreg_s11b>; |
| vddrfa1p7-supply = <&vreg_s1c>; |
| |
| max-speed = <3200000>; |
| |
| enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>; |
| swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&bt_default>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &usb_0 { |
| status = "okay"; |
| }; |
| |
| &usb_0_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_0_hsphy { |
| vdda-pll-supply = <&vreg_l9d>; |
| vdda18-supply = <&vreg_l1c>; |
| vdda33-supply = <&vreg_l7d>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_0_qmpphy { |
| vdda-phy-supply = <&vreg_l9d>; |
| vdda-pll-supply = <&vreg_l4d>; |
| |
| orientation-switch; |
| |
| status = "okay"; |
| }; |
| |
| &usb_0_qmpphy_dp_in { |
| remote-endpoint = <&mdss0_dp0_out>; |
| }; |
| |
| &usb_0_qmpphy_out { |
| remote-endpoint = <&pmic_glink_con0_ss>; |
| }; |
| |
| &usb_0_role_switch { |
| remote-endpoint = <&pmic_glink_con0_hs>; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_hsphy { |
| vdda-pll-supply = <&vreg_l4b>; |
| vdda18-supply = <&vreg_l1c>; |
| vdda33-supply = <&vreg_l13c>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_qmpphy { |
| vdda-phy-supply = <&vreg_l4b>; |
| vdda-pll-supply = <&vreg_l3b>; |
| |
| orientation-switch; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_qmpphy_dp_in { |
| remote-endpoint = <&mdss0_dp1_out>; |
| }; |
| |
| &usb_1_qmpphy_out { |
| remote-endpoint = <&pmic_glink_con1_ss>; |
| }; |
| |
| &usb_1_role_switch { |
| remote-endpoint = <&pmic_glink_con1_hs>; |
| }; |
| |
| &vamacro { |
| pinctrl-0 = <&dmic01_default>, <&dmic02_default>; |
| pinctrl-names = "default"; |
| |
| vdd-micb-supply = <&vreg_s10b>; |
| |
| qcom,dmic-sample-rate = <4800000>; |
| |
| status = "okay"; |
| }; |
| |
| &wsamacro { |
| status = "okay"; |
| }; |
| |
| &xo_board_clk { |
| clock-frequency = <38400000>; |
| }; |
| |
| /* PINCTRL */ |
| |
| &lpass_tlmm { |
| status = "okay"; |
| }; |
| |
| &pmc8280_1_gpios { |
| edp_bl_en: edp-bl-en-state { |
| pins = "gpio8"; |
| function = "normal"; |
| }; |
| |
| edp_bl_reg_en: edp-bl-reg-en-state { |
| pins = "gpio9"; |
| function = "normal"; |
| }; |
| |
| misc_3p3_reg_en: misc-3p3-reg-en-state { |
| pins = "gpio1"; |
| function = "normal"; |
| }; |
| }; |
| |
| &pmc8280_2_gpios { |
| wwan_sw_en: wwan-sw-en-state { |
| pins = "gpio1"; |
| function = "normal"; |
| }; |
| }; |
| |
| &pmc8280c_gpios { |
| edp_bl_pwm: edp-bl-pwm-state { |
| pins = "gpio8"; |
| function = "func1"; |
| }; |
| }; |
| |
| &pmr735a_gpios { |
| hastings_reg_en: hastings-reg-en-state { |
| pins = "gpio1"; |
| function = "normal"; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <70 2>, <74 6>, <125 2>, <128 2>, <154 4>; |
| |
| bt_default: bt-default-state { |
| hstp-bt-en-pins { |
| pins = "gpio133"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| hstp-sw-ctrl-pins { |
| pins = "gpio132"; |
| function = "gpio"; |
| bias-pull-down; |
| }; |
| }; |
| |
| edp_reg_en: edp-reg-en-state { |
| pins = "gpio25"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| hall_int_n_default: hall-int-n-state { |
| pins = "gpio107"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| i2c4_default: i2c4-default-state { |
| pins = "gpio171", "gpio172"; |
| function = "qup4"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| i2c21_default: i2c21-default-state { |
| pins = "gpio81", "gpio82"; |
| function = "qup21"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| kybd_default: kybd-default-state { |
| disable-pins { |
| pins = "gpio102"; |
| function = "gpio"; |
| output-low; |
| }; |
| |
| int-n-pins { |
| pins = "gpio104"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| reset-pins { |
| pins = "gpio105"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| }; |
| |
| nvme_reg_en: nvme-reg-en-state { |
| pins = "gpio135"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| pcie2a_default: pcie2a-default-state { |
| clkreq-n-pins { |
| pins = "gpio142"; |
| function = "pcie2a_clkreq"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| perst-n-pins { |
| pins = "gpio143"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio145"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pcie3a_default: pcie3a-default-state { |
| clkreq-n-pins { |
| pins = "gpio150"; |
| function = "pcie3a_clkreq"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| perst-n-pins { |
| pins = "gpio151"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio148"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pcie4_default: pcie4-default-state { |
| clkreq-n-pins { |
| pins = "gpio140"; |
| function = "pcie4_clkreq"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| perst-n-pins { |
| pins = "gpio141"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio139"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| spkr_1_sd_n_default: spkr-1-sd-n-default-state { |
| perst-n-pins { |
| pins = "gpio178"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-high; |
| }; |
| }; |
| |
| spkr_2_sd_n_default: spkr-2-sd-n-default-state { |
| perst-n-pins { |
| pins = "gpio179"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-high; |
| }; |
| }; |
| |
| tpad_default: tpad-default-state { |
| int-n-pins { |
| pins = "gpio182"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| }; |
| |
| ts0_default: ts0-default-state { |
| int-n-pins { |
| pins = "gpio175"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| reset-n-pins { |
| pins = "gpio99"; |
| function = "gpio"; |
| output-high; |
| drive-strength = <16>; |
| }; |
| }; |
| |
| uart2_default: uart2-default-state { |
| cts-pins { |
| pins = "gpio121"; |
| function = "qup2"; |
| bias-bus-hold; |
| }; |
| |
| rts-pins { |
| pins = "gpio122"; |
| function = "qup2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rx-pins { |
| pins = "gpio124"; |
| function = "qup2"; |
| bias-pull-up; |
| }; |
| |
| tx-pins { |
| pins = "gpio123"; |
| function = "qup2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| usb0_sbu_default: usb0-sbu-state { |
| oe-n-pins { |
| pins = "gpio101"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <16>; |
| output-high; |
| }; |
| |
| sel-pins { |
| pins = "gpio164"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| }; |
| |
| usb1_sbu_default: usb1-sbu-state { |
| oe-n-pins { |
| pins = "gpio48"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <16>; |
| output-high; |
| }; |
| |
| sel-pins { |
| pins = "gpio47"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| }; |
| |
| wcd_default: wcd-default-state { |
| reset-pins { |
| pins = "gpio106"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| }; |
| }; |
