| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> |
| */ |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include "sdm845.dtsi" |
| #include "pm8005.dtsi" |
| #include "pm8998.dtsi" |
| #include "pmi8998.dtsi" |
| |
| / { |
| qcom,msm-id = <321 0x20001>; /* SDM845 v2.1 */ |
| qcom,board-id = <8 0>; |
| |
| aliases { |
| serial0 = &uart6; |
| serial1 = &uart9; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&focus_n &snapshot_n &vol_down_n &vol_up_n>; |
| pinctrl-names = "default"; |
| |
| key-camera-focus { |
| label = "Camera Focus"; |
| gpios = <&pm8998_gpios 2 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_CAMERA_FOCUS>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| wakeup-source; |
| }; |
| |
| key-camera-snapshot { |
| label = "Camera Snapshot"; |
| gpios = <&pm8998_gpios 7 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_CAMERA>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| wakeup-source; |
| }; |
| |
| key-volume-down { |
| label = "Volume Down"; |
| gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| wakeup-source; |
| }; |
| |
| key-volume-up { |
| label = "Volume Up"; |
| gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| wakeup-source; |
| }; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| }; |
| |
| vreg_s4a_1p8: pm8998-smps4 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_s4a_1p8"; |
| |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| |
| vin-supply = <&vph_pwr>; |
| }; |
| |
| reserved-memory { |
| /* SONY was cool and didn't diverge from MTP this time, yay! */ |
| cont_splash_mem: memory@9d400000 { |
| reg = <0x0 0x9d400000 0x0 0x2400000>; |
| no-map; |
| }; |
| |
| ramoops@ffc00000 { |
| compatible = "ramoops"; |
| reg = <0x0 0xffc00000 0x0 0x100000>; |
| record-size = <0x10000>; |
| console-size = <0x60000>; |
| ftrace-size = <0x10000>; |
| pmsg-size = <0x20000>; |
| ecc-size = <16>; |
| no-map; |
| }; |
| }; |
| }; |
| |
| &adsp_pas { |
| firmware-name = "qcom/sdm845/Sony/tama/adsp.mbn"; |
| status = "okay"; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8998-rpmh-regulators"; |
| qcom,pmic-id = "a"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| vdd-s7-supply = <&vph_pwr>; |
| vdd-s8-supply = <&vph_pwr>; |
| vdd-s9-supply = <&vph_pwr>; |
| vdd-s10-supply = <&vph_pwr>; |
| vdd-s11-supply = <&vph_pwr>; |
| vdd-s12-supply = <&vph_pwr>; |
| vdd-s13-supply = <&vph_pwr>; |
| vdd-l1-l27-supply = <&vreg_s7a_0p9>; |
| vdd-l2-l8-l17-supply = <&vreg_s3a_1p3>; |
| vdd-l3-l11-supply = <&vreg_s7a_0p9>; |
| vdd-l4-l5-supply = <&vreg_s7a_0p9>; |
| vdd-l6-supply = <&vph_pwr>; |
| vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; |
| vdd-l9-supply = <&vreg_s5a_1p9>; |
| vdd-l10-l23-l25-supply = <&src_vreg_bob>; |
| vdd-l13-l19-l21-supply = <&src_vreg_bob>; |
| vdd-l16-l28-supply = <&src_vreg_bob>; |
| vdd-l18-l22-supply = <&src_vreg_bob>; |
| vdd-l20-l24-supply = <&src_vreg_bob>; |
| vdd-l26-supply = <&vreg_s3a_1p3>; |
| vin-lvs-1-2-supply = <&vreg_s4a_1p8>; |
| |
| vreg_s2a_1p1: smps2 { |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| }; |
| |
| vreg_s3a_1p3: smps3 { |
| regulator-min-microvolt = <1352000>; |
| regulator-max-microvolt = <1352000>; |
| }; |
| |
| vreg_s5a_1p9: smps5 { |
| regulator-min-microvolt = <1904000>; |
| regulator-max-microvolt = <2040000>; |
| }; |
| |
| vreg_s7a_0p9: smps7 { |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1028000>; |
| }; |
| |
| vreg_l1a_0p9: ldo1 { |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2a_1p2: ldo2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_l3a_1p0: ldo3 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5a_0p8: ldo5 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6a_1p8: ldo6 { |
| regulator-min-microvolt = <1856000>; |
| regulator-max-microvolt = <1856000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7a_1p8: ldo7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8a_1p2: ldo8 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1248000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9a_1p7: ldo9 { |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <2928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10a_1p7: ldo10 { |
| regulator-min-microvolt = <1704000>; |
| regulator-max-microvolt = <2928000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11a_1p0: ldo11 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1048000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12a_1p8: ldo12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13a_1p8: ldo13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14a_1p8: ldo14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-system-load = <62000>; |
| }; |
| |
| vreg_l15a_1p8: ldo15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16a_2p7: ldo16 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2704000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17a_1p3: ldo17 { |
| regulator-min-microvolt = <1304000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l18a_2p7: ldo18 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l19a_2p7: ldo19 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| |
| /* |
| * The driver *really* doesn't want this regualtor to exist, |
| * saying that it could not get the current voltage (-ENOTRECOVERABLE) |
| * even though it surely is used on these devices (as a voltage |
| * source for camera autofocus) |
| */ |
| status = "disabled"; |
| }; |
| |
| vreg_l20a_2p7: ldo20 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l21a_2p7: ldo21 { |
| regulator-min-microvolt = <2704000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l22a_2p8: ldo22 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l23a_3p0: ldo23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l24a_3p1: ldo24 { |
| regulator-min-microvolt = <3088000>; |
| regulator-max-microvolt = <3088000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l25a_3p0: ldo25 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l26a_1p2: ldo26 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l28a_2p8: ldo28 { |
| regulator-min-microvolt = <2856000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-system-load = <100000>; |
| }; |
| |
| vreg_lvs1a_1p8: lvs1 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_lvs2a_1p8: lvs2 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pmi8998-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| src_vreg_bob: bob { |
| regulator-min-microvolt = <3312000>; |
| regulator-max-microvolt = <3600000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pm8005-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| |
| vreg_s3c_0p6: smps3 { |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <600000>; |
| }; |
| }; |
| }; |
| |
| &cdsp_pas { |
| firmware-name = "qcom/sdm845/Sony/tama/cdsp.mbn"; |
| status = "okay"; |
| }; |
| |
| &gcc { |
| protected-clocks = <GCC_QSPI_CORE_CLK>, |
| <GCC_QSPI_CORE_CLK_SRC>, |
| <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, |
| <GCC_LPASS_Q6_AXI_CLK>, |
| <GCC_LPASS_SWAY_CLK>; |
| }; |
| |
| &gmu { |
| status = "okay"; |
| }; |
| |
| &gpi_dma0 { |
| status = "okay"; |
| }; |
| |
| &gpi_dma1 { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| memory-region = <&gpu_mem>; |
| firmware-name = "qcom/sdm845/Sony/tama/a630_zap.mbn"; |
| }; |
| }; |
| |
| &i2c5 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| touchscreen: touchscreen@2c { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x2c>; |
| |
| interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>; |
| vdd-supply = <&vreg_l14a_1p8>; |
| /* |
| * This is a blatant abuse of OF, but the panel driver *needs* |
| * to probe first, as the power/gpio switching needs to be precisely |
| * timed in order for both the display and touch panel to function properly. |
| */ |
| incell-supply = <&panel>; |
| |
| syna,reset-delay-ms = <220>; |
| syna,startup-delay-ms = <1000>; |
| |
| pinctrl-0 = <&ts_default>; |
| pinctrl-1 = <&ts_sleep>; |
| pinctrl-names = "default", "sleep"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| rmi4-f01@1 { |
| reg = <0x01>; |
| syna,nosleep-mode = <1>; |
| }; |
| |
| rmi4-f12@12 { |
| reg = <0x12>; |
| syna,sensor-type = <1>; |
| }; |
| }; |
| }; |
| |
| &i2c10 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| /* Qcom SMB1355 @ 8, c */ |
| /* NXP PN547 NFC @ 28 */ |
| /* Renesas IDTP9221 Qi charger @ 61 */ |
| }; |
| |
| &i2c14 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| /* SONY ToF sensor @ 52 */ |
| /* AMS TCS3490 RGB+IR color sensor @ 72 */ |
| }; |
| |
| &ibb { |
| qcom,discharge-resistor-kohms = <300>; |
| regulator-min-microvolt = <5500000>; |
| regulator-max-microvolt = <5700000>; |
| regulator-min-microamp = <0>; |
| regulator-max-microamp = <800000>; |
| regulator-over-current-protection; |
| regulator-soft-start; |
| regulator-pull-down; |
| }; |
| |
| &lab { |
| regulator-min-microvolt = <5500000>; |
| regulator-max-microvolt = <5700000>; |
| regulator-min-microamp = <200000>; |
| regulator-max-microamp = <200000>; |
| regulator-over-current-protection; |
| regulator-soft-start; |
| regulator-pull-down; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| vdda-supply = <&vreg_l26a_1p2>; |
| status = "okay"; |
| |
| panel: panel@0 { |
| /* The compatible is assigned in device DTs. */ |
| reg = <0>; |
| |
| backlight = <&pmi8998_wled>; |
| vddio-supply = <&vreg_l14a_1p8>; |
| vsp-supply = <&lab>; |
| vsn-supply = <&ibb>; |
| panel-reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; |
| touch-reset-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&sde_dsi_active &sde_te_active_sleep>; |
| pinctrl-1 = <&sde_dsi_sleep &sde_te_active_sleep>; |
| pinctrl-names = "default", "sleep"; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_out { |
| remote-endpoint = <&panel_in>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &mdss_dsi0_phy { |
| vdds-supply = <&vreg_l1a_0p9>; |
| status = "okay"; |
| }; |
| |
| &pm8998_gpios { |
| focus_n: focus-n-state { |
| pins = "gpio2"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| power-source = <0>; |
| bias-pull-up; |
| input-enable; |
| }; |
| |
| vol_down_n: vol-down-n-state { |
| pins = "gpio5"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| power-source = <0>; |
| bias-pull-up; |
| input-enable; |
| }; |
| |
| vol_up_n: vol-up-n-state { |
| pins = "gpio6"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| power-source = <0>; |
| bias-pull-up; |
| input-enable; |
| }; |
| |
| snapshot_n: snapshot-n-state { |
| pins = "gpio7"; |
| function = PMIC_GPIO_FUNC_NORMAL; |
| power-source = <0>; |
| bias-pull-up; |
| input-enable; |
| }; |
| }; |
| |
| &pmi8998_wled { |
| default-brightness = <800>; |
| qcom,switching-freq = <800>; |
| qcom,ovp-millivolt = <29600>; |
| qcom,current-boost-limit = <970>; |
| qcom,current-limit-microamp = <20000>; |
| qcom,enabled-strings = <0 1 2 3>; |
| status = "okay"; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_id_1 { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| |
| vmmc-supply = <&vreg_l21a_2p7>; |
| vqmmc-supply = <&vreg_l13a_1p8>; |
| cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>; |
| pinctrl-0 = <&sdc2_default_state>; |
| pinctrl-names = "default"; |
| bus-width = <4>; |
| no-sdio; |
| no-mmc; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <0 4>, <81 4>; |
| |
| sdc2_default_state: sdc2-default-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| cmd-pins { |
| pins = "sdc2_cmd"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| |
| data-pins { |
| pins = "sdc2_data"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sde_dsi_active: sde-dsi-active-state { |
| pins = "gpio6"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| sde_dsi_sleep: sde-dsi-sleep-state { |
| pins = "gpio6"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| sde_te_active_sleep: sde-te-active-sleep-state { |
| pins = "gpio10"; |
| function = "mdp_vsync"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| ts_default: ts-default-state { |
| reset-pins { |
| pins = "gpio99"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| int-pins { |
| pins = "gpio125"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| ts_sleep: ts-sleep-state { |
| reset-pins { |
| pins = "gpio99"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| int-pins { |
| pins = "gpio125"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| }; |
| }; |
| |
| &uart6 { |
| status = "okay"; |
| }; |
| |
| &uart9 { |
| status = "okay"; |
| }; |
| |
| /* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */ |
| &ufs_mem_hc { status = "disabled"; }; |
| &ufs_mem_phy { status = "disabled"; }; |
| |
| &usb_1 { |
| status = "okay"; |
| |
| qcom,select-utmi-as-pipe-clk; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "peripheral"; |
| |
| maximum-speed = "high-speed"; |
| phys = <&usb_1_hsphy>; |
| phy-names = "usb2-phy"; |
| }; |
| |
| &usb_1_hsphy { |
| status = "okay"; |
| |
| vdd-supply = <&vreg_l1a_0p9>; |
| vdda-pll-supply = <&vreg_l12a_1p8>; |
| vdda-phy-dpdm-supply = <&vreg_l24a_3p1>; |
| }; |
| |
| &venus { |
| firmware-name = "qcom/sdm845/Sony/tama/venus.mbn"; |
| status = "okay"; |
| }; |
