| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Lenovo Yoga C630 |
| * |
| * Copyright (c) 2019, Linaro Ltd. |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/input/gpio-keys.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include <dt-bindings/sound/qcom,q6afe.h> |
| #include <dt-bindings/sound/qcom,q6asm.h> |
| #include "sdm850.dtsi" |
| #include "sdm845-wcd9340.dtsi" |
| #include "pm8998.dtsi" |
| |
| /* |
| * Update following upstream (sdm845.dtsi) reserved |
| * memory mappings for firmware loading to succeed |
| * and enable the IPA device. |
| */ |
| /delete-node/ &ipa_fw_mem; |
| /delete-node/ &ipa_gsi_mem; |
| /delete-node/ &gpu_mem; |
| /delete-node/ &adsp_mem; |
| /delete-node/ &wlan_msa_mem; |
| |
| / { |
| model = "Lenovo Yoga C630"; |
| compatible = "lenovo,yoga-c630", "qcom,sdm845"; |
| chassis-type = "convertible"; |
| |
| aliases { |
| serial0 = &uart9; |
| serial1 = &uart6; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lid_pin_active>, <&mode_pin_active>; |
| |
| switch-lid { |
| gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| wakeup-source; |
| wakeup-event-action = <EV_ACT_DEASSERTED>; |
| }; |
| |
| switch-mode { |
| gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_TABLET_MODE>; |
| }; |
| }; |
| |
| /* Reserved memory changes for IPA */ |
| reserved-memory { |
| wlan_msa_mem: memory@8c400000 { |
| reg = <0 0x8c400000 0 0x100000>; |
| no-map; |
| }; |
| |
| gpu_mem: memory@8c515000 { |
| reg = <0 0x8c515000 0 0x2000>; |
| no-map; |
| }; |
| |
| ipa_fw_mem: memory@8c517000 { |
| reg = <0 0x8c517000 0 0x5a000>; |
| no-map; |
| }; |
| |
| adsp_mem: memory@8c600000 { |
| reg = <0 0x8c600000 0 0x1a00000>; |
| no-map; |
| }; |
| }; |
| |
| sw_edp_1p2: edp-1p2-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "sw_edp_1p2"; |
| |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| |
| pinctrl-0 = <&sw_edp_1p2_en>; |
| pinctrl-names = "default"; |
| |
| gpio = <&pm8998_gpios 9 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| vin-supply = <&vreg_l2a_1p2>; |
| }; |
| |
| sn65dsi86_refclk: sn65dsi86-refclk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| |
| clock-frequency = <19200000>; |
| }; |
| |
| vph_pwr: regulator-vph-pwr { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| }; |
| |
| vlcm_3v3: regulator-vlcm-3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vlcm_3v3"; |
| |
| vin-supply = <&vph_pwr>; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 88 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&sn65dsi86 1000000>; |
| enable-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| &adsp_pas { |
| firmware-name = "qcom/sdm850/LENOVO/81JL/qcadsp850.mbn"; |
| status = "okay"; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8998-rpmh-regulators"; |
| qcom,pmic-id = "a"; |
| |
| vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; |
| vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; |
| |
| vreg_s2a_1p125: smps2 { |
| }; |
| |
| vreg_s3a_1p35: smps3 { |
| regulator-min-microvolt = <1352000>; |
| regulator-max-microvolt = <1352000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s4a_1p8: smps4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s5a_2p04: smps5 { |
| regulator-min-microvolt = <2040000>; |
| regulator-max-microvolt = <2040000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s7a_1p025: smps7 { |
| }; |
| |
| vdd_qusb_hs0: |
| vdda_hp_pcie_core: |
| vdda_mipi_csi0_0p9: |
| vdda_mipi_csi1_0p9: |
| vdda_mipi_csi2_0p9: |
| vdda_mipi_dsi0_pll: |
| vdda_mipi_dsi1_pll: |
| vdda_qlink_lv: |
| vdda_qlink_lv_ck: |
| vdda_qrefs_0p875: |
| vdda_pcie_core: |
| vdda_pll_cc_ebi01: |
| vdda_pll_cc_ebi23: |
| vdda_sp_sensor: |
| vdda_ufs1_core: |
| vdda_ufs2_core: |
| vdda_usb1_ss_core: |
| vdda_usb2_ss_core: |
| vreg_l1a_0p875: ldo1 { |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vddpx_10: |
| vreg_l2a_1p2: ldo2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_l3a_1p0: ldo3 { |
| }; |
| |
| vdd_wcss_cx: |
| vdd_wcss_mx: |
| vdda_wcss_pll: |
| vreg_l5a_0p8: ldo5 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vddpx_13: |
| vreg_l6a_1p8: ldo6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7a_1p8: ldo7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8a_1p2: ldo8 { |
| }; |
| |
| vreg_l9a_1p8: ldo9 { |
| }; |
| |
| vreg_l10a_1p8: ldo10 { |
| }; |
| |
| vreg_l11a_1p0: ldo11 { |
| }; |
| |
| vdd_qfprom: |
| vdd_qfprom_sp: |
| vdda_apc1_cs_1p8: |
| vdda_gfx_cs_1p8: |
| vdda_qrefs_1p8: |
| vdda_qusb_hs0_1p8: |
| vddpx_11: |
| vreg_l12a_1p8: ldo12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vddpx_2: |
| vreg_l13a_2p95: ldo13 { |
| }; |
| |
| vreg_l14a_1p88: ldo14 { |
| regulator-min-microvolt = <1880000>; |
| regulator-max-microvolt = <1880000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_l15a_1p8: ldo15 { |
| }; |
| |
| vreg_l16a_2p7: ldo16 { |
| }; |
| |
| vreg_l17a_1p3: ldo17 { |
| regulator-min-microvolt = <1304000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l18a_2p7: ldo18 { |
| }; |
| |
| vreg_l19a_3p0: ldo19 { |
| regulator-min-microvolt = <3100000>; |
| regulator-max-microvolt = <3108000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l20a_2p95: ldo20 { |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l21a_2p95: ldo21 { |
| }; |
| |
| vreg_l22a_2p85: ldo22 { |
| }; |
| |
| vreg_l23a_3p3: ldo23 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3312000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vdda_qusb_hs0_3p1: |
| vreg_l24a_3p075: ldo24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3083000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l25a_3p3: ldo25 { |
| regulator-min-microvolt = <3104000>; |
| regulator-max-microvolt = <3112000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vdda_hp_pcie_1p2: |
| vdda_hv_ebi0: |
| vdda_hv_ebi1: |
| vdda_hv_ebi2: |
| vdda_hv_ebi3: |
| vdda_mipi_csi_1p25: |
| vdda_mipi_dsi0_1p2: |
| vdda_mipi_dsi1_1p2: |
| vdda_pcie_1p2: |
| vdda_ufs1_1p2: |
| vdda_ufs2_1p2: |
| vdda_usb1_ss_1p2: |
| vdda_usb2_ss_1p2: |
| vreg_l26a_1p2: ldo26 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1208000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l28a_3p0: ldo28 { |
| }; |
| |
| vreg_lvs1a_1p8: lvs1 { |
| }; |
| |
| vreg_lvs2a_1p8: lvs2 { |
| }; |
| }; |
| }; |
| |
| &cdsp_pas { |
| firmware-name = "qcom/sdm850/LENOVO/81JL/qccdsp850.mbn"; |
| status = "okay"; |
| }; |
| |
| &gcc { |
| protected-clocks = <GCC_QSPI_CORE_CLK>, |
| <GCC_QSPI_CORE_CLK_SRC>, |
| <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, |
| <GCC_LPASS_Q6_AXI_CLK>, |
| <GCC_LPASS_SWAY_CLK>; |
| }; |
| |
| &gmu { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| zap-shader { |
| memory-region = <&gpu_mem>; |
| firmware-name = "qcom/sdm850/LENOVO/81JL/qcdxkmsuc850.mbn"; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| }; |
| |
| &i2c3 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| /* Overwrite pinctrl-0 from sdm845.dtsi */ |
| pinctrl-0 = <&qup_i2c3_default &i2c3_hid_active>; |
| |
| tsel: hid@15 { |
| compatible = "hid-over-i2c"; |
| reg = <0x15>; |
| hid-descr-addr = <0x1>; |
| |
| interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| tsc2: hid@2c { |
| compatible = "hid-over-i2c"; |
| reg = <0x2c>; |
| hid-descr-addr = <0x20>; |
| |
| interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| &i2c5 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| tsc1: hid@10 { |
| compatible = "hid-over-i2c"; |
| reg = <0x10>; |
| hid-descr-addr = <0x1>; |
| |
| interrupts-extended = <&tlmm 125 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c5_hid_active>; |
| }; |
| }; |
| |
| &i2c10 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| sn65dsi86: bridge@2c { |
| compatible = "ti,sn65dsi86"; |
| reg = <0x2c>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sn65dsi86_pin_active>; |
| |
| enable-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; |
| |
| vcca-supply = <&sw_edp_1p2>; |
| vcc-supply = <&sw_edp_1p2>; |
| vpll-supply = <&vreg_l14a_1p88>; |
| vccio-supply = <&vreg_l14a_1p88>; |
| |
| clocks = <&sn65dsi86_refclk>; |
| clock-names = "refclk"; |
| |
| no-hpd; |
| #pwm-cells = <1>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| sn65dsi86_in_a: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| sn65dsi86_out: endpoint { |
| remote-endpoint = <&panel_in_edp>; |
| }; |
| }; |
| }; |
| |
| aux-bus { |
| panel: panel { |
| compatible = "boe,nv133fhm-n61"; |
| backlight = <&backlight>; |
| power-supply = <&vlcm_3v3>; |
| |
| port { |
| panel_in_edp: endpoint { |
| remote-endpoint = <&sn65dsi86_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c11 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| ecsh: hid@5c { |
| compatible = "hid-over-i2c"; |
| reg = <0x5c>; |
| hid-descr-addr = <0x1>; |
| |
| interrupts-extended = <&tlmm 92 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c11_hid_active>; |
| }; |
| }; |
| |
| &ipa { |
| qcom,gsi-loader = "self"; |
| memory-region = <&ipa_fw_mem>; |
| status = "okay"; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| status = "okay"; |
| vdda-supply = <&vreg_l26a_1p2>; |
| |
| ports { |
| port@1 { |
| endpoint { |
| remote-endpoint = <&sn65dsi86_in_a>; |
| data-lanes = <0 1 2 3>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_phy { |
| status = "okay"; |
| vdds-supply = <&vreg_l1a_0p875>; |
| }; |
| |
| &mss_pil { |
| status = "okay"; |
| firmware-name = "qcom/sdm850/LENOVO/81JL/qcdsp1v2850.mbn", "qcom/sdm850/LENOVO/81JL/qcdsp2850.mbn"; |
| }; |
| |
| &pm8998_gpios { |
| /* This pin is pulled down by a fixed resistor */ |
| sw_edp_1p2_en: pm8998-gpio9-state { |
| pins = "gpio9"; |
| function = "normal"; |
| bias-disable; |
| qcom,drive-strength = <0>; |
| }; |
| }; |
| |
| &qup_i2c10_default { |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| &qup_i2c12_default { |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_id_1 { |
| status = "okay"; |
| }; |
| |
| &q6asmdai { |
| dai@0 { |
| reg = <0>; |
| }; |
| |
| dai@1 { |
| reg = <1>; |
| }; |
| |
| dai@2 { |
| reg = <2>; |
| }; |
| }; |
| |
| &sound { |
| compatible = "lenovo,yoga-c630-sndcard", "qcom,sdm845-sndcard"; |
| model = "Lenovo-YOGA-C630-13Q50"; |
| |
| audio-routing = |
| "RX_BIAS", "MCLK", |
| "AMIC2", "MIC BIAS2", |
| "SpkrLeft IN", "SPK1 OUT", |
| "SpkrRight IN", "SPK2 OUT", |
| "MM_DL1", "MultiMedia1 Playback", |
| "MM_DL3", "MultiMedia3 Playback", |
| "MultiMedia2 Capture", "MM_UL2"; |
| |
| mm1-dai-link { |
| link-name = "MultiMedia1"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; |
| }; |
| }; |
| |
| mm2-dai-link { |
| link-name = "MultiMedia2"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; |
| }; |
| }; |
| |
| mm3-dai-link { |
| link-name = "MultiMedia3"; |
| cpu { |
| sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; |
| }; |
| }; |
| |
| slim-dai-link { |
| link-name = "SLIM Playback"; |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_0_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>; |
| }; |
| }; |
| |
| slimcap-dai-link { |
| link-name = "SLIM Capture"; |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_0_TX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd9340 1>; |
| }; |
| }; |
| |
| slim-wcd-dai-link { |
| link-name = "SLIM WCD Playback"; |
| cpu { |
| sound-dai = <&q6afedai SLIMBUS_1_RX>; |
| }; |
| |
| platform { |
| sound-dai = <&q6routing>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd9340 2>; |
| }; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <0 4>, <81 4>; |
| |
| sn65dsi86_pin_active: sn65dsi86-enable-state { |
| pins = "gpio96"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| i2c3_hid_active: i2c2-hid-active-state { |
| pins = "gpio37"; |
| function = "gpio"; |
| |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| i2c5_hid_active: i2c5-hid-active-state { |
| pins = "gpio125"; |
| function = "gpio"; |
| |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| i2c11_hid_active: i2c11-hid-active-state { |
| pins = "gpio92"; |
| function = "gpio"; |
| |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| lid_pin_active: lid-pin-state { |
| pins = "gpio124"; |
| function = "gpio"; |
| |
| bias-disable; |
| }; |
| |
| mode_pin_active: mode-pin-state { |
| pins = "gpio95"; |
| function = "gpio"; |
| |
| bias-disable; |
| }; |
| }; |
| |
| &uart6 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart6_4pin>; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,wcn3990-bt"; |
| |
| vddio-supply = <&vreg_s4a_1p8>; |
| vddxo-supply = <&vreg_l7a_1p8>; |
| vddrf-supply = <&vreg_l17a_1p3>; |
| vddch0-supply = <&vreg_l25a_3p3>; |
| vddch1-supply = <&vreg_l23a_3p3>; |
| max-speed = <3200000>; |
| }; |
| }; |
| |
| &uart9 { |
| status = "okay"; |
| }; |
| |
| &ufs_mem_hc { |
| status = "okay"; |
| |
| reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; |
| |
| vcc-supply = <&vreg_l20a_2p95>; |
| vcc-max-microamp = <600000>; |
| }; |
| |
| &ufs_mem_phy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vdda_ufs1_core>; |
| vdda-pll-supply = <&vdda_ufs1_1p2>; |
| }; |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_hsphy { |
| status = "okay"; |
| |
| vdd-supply = <&vdda_usb1_ss_core>; |
| vdda-pll-supply = <&vdda_qusb_hs0_1p8>; |
| vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; |
| |
| qcom,imp-res-offset-value = <8>; |
| qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>; |
| qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>; |
| qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; |
| }; |
| |
| &usb_1_qmpphy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vdda_usb1_ss_1p2>; |
| vdda-pll-supply = <&vdda_usb1_ss_core>; |
| }; |
| |
| &usb_2 { |
| status = "okay"; |
| }; |
| |
| &usb_2_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_2_hsphy { |
| status = "okay"; |
| |
| vdd-supply = <&vdda_usb2_ss_core>; |
| vdda-pll-supply = <&vdda_qusb_hs0_1p8>; |
| vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; |
| |
| qcom,imp-res-offset-value = <8>; |
| qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>; |
| }; |
| |
| &usb_2_qmpphy { |
| status = "okay"; |
| |
| vdda-phy-supply = <&vdda_usb2_ss_1p2>; |
| vdda-pll-supply = <&vdda_usb2_ss_core>; |
| }; |
| |
| &venus { |
| firmware-name = "qcom/sdm850/LENOVO/81JL/qcvss850.mbn"; |
| status = "okay"; |
| }; |
| |
| &wcd9340 { |
| reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>; |
| vdd-buck-supply = <&vreg_s4a_1p8>; |
| vdd-buck-sido-supply = <&vreg_s4a_1p8>; |
| vdd-tx-supply = <&vreg_s4a_1p8>; |
| vdd-rx-supply = <&vreg_s4a_1p8>; |
| vdd-io-supply = <&vreg_s4a_1p8>; |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| |
| swm: swm@c85 { |
| left_spkr: speaker@0,3 { |
| compatible = "sdw10217211000"; |
| reg = <0 3>; |
| powerdown-gpios = <&wcdgpio 1 GPIO_ACTIVE_LOW>; |
| #thermal-sensor-cells = <0>; |
| sound-name-prefix = "SpkrLeft"; |
| #sound-dai-cells = <0>; |
| }; |
| |
| right_spkr: speaker@0,4 { |
| compatible = "sdw10217211000"; |
| powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_LOW>; |
| reg = <0 4>; |
| #thermal-sensor-cells = <0>; |
| sound-name-prefix = "SpkrRight"; |
| #sound-dai-cells = <0>; |
| }; |
| }; |
| }; |
| |
| &wifi { |
| status = "okay"; |
| |
| vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; |
| vdd-1.8-xo-supply = <&vreg_l7a_1p8>; |
| vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; |
| vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; |
| vdd-3.3-ch1-supply = <&vreg_l23a_3p3>; |
| |
| qcom,snoc-host-cap-8bit-quirk; |
| }; |
| |
| &crypto { |
| /* FIXME: qce_start triggers an SError */ |
| status = "disabled"; |
| }; |
